you’ve got to cnc this! - mta...the one-lok cnc vise is an evolution in workholding. the design of...
TRANSCRIPT
You’ve got to CNC this!
The New One-LokTM Single Station CNC ViseFEATURING Chip-Free Solid Base | BoltFastTM Jaw System | QwikSlide Moveable Jaw
The One-Lok CNC Vise is an evolution in
workholding. The design of every other vise on the
market today is based on 1950s knee mill technology,
but, as every machinist knows, CNC milling is a
completely different work environment.
The One-Lok was created from the ground
up for use in CNC milling. Its unique design
makes it possible to capture
dramatic improvements in
speed, precision, and versatility.
The following highlights some of
the key differences between knee
mill vises and the design of the One-Lok
CNC Vise.
CNC the difference.
KneeMillVise
CNC Vise
One-LokResults
Delivers consistent partplacement across multipleusers and a wide range ofholding forces.
Saves valuable time onexpensive CNC machines withthe ability to make rapidworkholding adjustments.
Makes more parts with lessfrustration—change jaws inseconds with better than0.0008” repeatability.
Push clamping resultsin jaw deflection.
It takes about 70 turns ofthe handle to fully openand close a knee mill vise.
Cap screws need to beremoved to change jaws. No way to accurately relocate.
Squeeze clampingminimizes deflection.
The QwikSlide moveablejaw opens and closes in seconds.
BoltFast jaw system changes over in seconds with excellent repeatability.
NEW
TEC
HN
OLO
GY
One-Lok Single Station CNC ViseCOL1520
Standard One-Lok CNC Vise includes:• BoltFast hard jaw set• Toe clamps, set of 4• Swivel wrench• T-wrench
One-Lok Single Station CNC Vise
New BoltFast Jaw SystemNo more knuckle scraping! With Chick’sBoltFast jaw system, soft and hard jaws canbe changed with a single turn of the lockingscrew—while providing repeatability of betterthan 0.0008” (0.02mm).
Fixed Jaw Deflection Virtually EliminatedThe CNC Vise is engineered to apply “squeezeclamping,” which allows up to 10,000 lbs. ofholding force.
No Chip Traps In the BaseUnique in the industry, the One-Lok’shardened, precision-ground, cast iron base is a solid working surface. No open waysmeans you’ll never have to fish out smallworkpieces or clean chip build-up from inside the CNC Vise.
QwikSlide Moveable JawThe moveable jaw may be unlocked to slideforward or back for rapid set-up. No speedhandles needed!
The One-Lok’s unique design offers speed, precision, and versatility.
1
2
3
4
Clamping Force/Torque
Holding Capacity
Standard One-Lok – 8”
With outboard hard jaws – 17”
8.00”
17.00”
RecommendedMaximum
1
2
3
4
17”
8”
6”
Time Is MoneyUsing a One-Lok (instead of a knee mill vise) will save a typical job shop at leastthree hours per week. Based on a $60 hourly rate, each One-Lok in your shopwill help you save $180 a week—which adds up to $9,360 a year.
One-Lok savings = $9,360/year
BoltFast Jaw System
The One-Lok’s BoltFast Jaw System holdslike a bolt—only better. We’ve designed aunique new way to change jaws quicklywithout sacrificing accuracy.
Slider interface pulls the jaw downinto the base while squeezing thejaw plate and fixed jaw together.
The accurate locating pin repeatsto within 0.0008”.
1
2
1
2
BoltFast jaws can be changed out in seconds, saving time and money.
Use a T-wrench to loosenthe BoltFast locking slider.
Remove the BoltFast jawby sliding it upward.
Place a new jawand tighten it down.
Foundation Locating StopsCLS0030
Outboard HardJaw SetCHJ1506
CNC Vise Accessories
Locating Keys (5/8”)CLK0625
Locating Keys (blank)CLKBLNK
WorkstopCWS1510
BoltFast Accessories
BoltFast SteppedHard Jaw SetCBFST-150-060.25” step jaweliminates the needfor parallels.
BoltFastSoft Jaw SetCBFSJ-150-50Machinable for fastrepeat setups andcustom partapplications.
BoltFast Bolt-OnJaw Spacer SetCBFSP-150Allows installation ofknee mill vise jawplates onto theBoltFast system.
Chick Workholding Solutions
Chick Workholding can help you improve productivityand profitability in your machining center. We workhand-in-hand with our customers and suppliers topursue innovation and deliver quality workholdingpackages, products, and accessories for vertical andhorizontal machining centers.
To order a One-Lok or discuss workholding challenges,give us a call at 724.772.1644.
chickworkholding.com | 724.772.1644