Summary

Build guide: http://danielnoree.com/the-openrc-f1-build-guide/

Questions & Answers: http://danielnoree.com/openrc-questions/ OpenRCElectronics: http://danielnoree.com/openrc-electronics/

Consider supporting me on Patreon: https://www.patreon.com/DanielNoree

Complete hardware/electronics lists and kits available here: http://danielnoree.com/openrc-electronics/

Please respect the license under which this project is released. Thank you!

Add your OpenR/C build to the buildmap: https://zeemaps.com/map?group=1888242

This is the OpenR/C Formula 1 car. It ́s the third generation OpenR/C carand this time around focus is on simplicity! You can print everything in PLAexcept the tires which are done in NinjaFlex! Of course you can print it inany material you like but for those that want to print a car but only havePLA at hand, this is the project for you!

Print the calibration cude to see if you need to finetune your printer for theM3 nuts to fit in their pockets.

A note on the servo saver. It ́s designed to be used with PLA, the upperand lower BOM applies force similar to a spring in a convetional servosaver. Of course the pressure depends on the type of material used, infilletc. Fine tuning can be done adding washer under or over the servo saver.

DanielNoree

OpenRC F1 car -1:10 RC Car

VIEW IN BROWSER

updated 16. 5. 2019 | published 16. 5. 2019

3D M

ODEL

ONLY

The "Main Turning Vane ́s" needs to have it ́s lower part trimmed using a"exacto knife". Then slide it in the chassie plate and push it over the "Lid"and it should snap into place-

Parts that need support added: Front Spoiler.stl Front.stl Rear Rim.stl RearWing.stl Servo Saver Lower.stl

Things to buy:

Ok, obviously you need some filament which you ́ll get from your favouritefilament supplier.

You also need M3 screws and nuts which you can get at your localhardware store. Check the BOM list for what to get.

Some bearings are needed aswell, check the BOM list or buy a kit fromFastEddyBearings.com: http://www.fasteddybearings.com/openrc-f1-sealed-bearing-kit/

Suggestion for electronics: http://danielnoree.com/openrc-electronics/

You can aslo ask questions in the Facebook group: https://www.facebook.com/groups/1111886228841596/

Short video: https://youtu.be/eTST_g2g2xQ

Please consider supporting me on Patreon: https://www.patreon.com/DanielNoree

Like my FaceBook page - https://www.facebook.com/Daniel-Nor%C3%A9e-576194949211855/ Subscribe to my YouTube channel - https://www.youtube.com/user/DanielNoree2

INSTAGRAM https://www.instagram.com/danielnoree/ TWITTER https://twitter.com/DanielNoree GOOGLE+ https://plus.google.com/u/1/+DanielNoree FACEBOOK https://www.facebook.com/daniel.noree

Hobby & Makers > RC & Robotics

f1 formula barspin openrc formula1 1 racecar rc

car

Model Files (.stl, .3mf, .obj, .amf) DOWNLOAD ALL FILES

39.5 KBupdated 16. 5. 2019

527.1 KBupdated 16. 5. 2019

262.8 KBupdated 16. 5. 2019

176.1 KBupdated 16. 5. 2019

119.2 KBupdated 16. 5. 2019

347.8 KBupdated 16. 5. 2019

255.0 KBupdated 16. 5. 2019

582.8 KBupdated 16. 5. 2019

119.3 KBupdated 16. 5. 2019

front_bom_block.stl

chassie_rear.stl

front_wheel_hub.stl

front_rim.stl

main_turning_vane_left.stl

chassie_front.stl

front_wheel_axle.stl

front_spoiler.stl

main_turning_vane_right.stl

64.4 KBupdated 16. 5. 2019

1.2 MBupdated 16. 5. 2019

587.0 KBupdated 16. 5. 2019

309.4 KBupdated 16. 5. 2019

289.0 KBupdated 16. 5. 2019

241.2 KBupdated 16. 5. 2019

349.2 KBupdated 16. 5. 2019

587.2 KBupdated 16. 5. 2019

1.2 MBupdated 16. 5. 2019

front_upper_bom.stl

center_lid.stl

rear_rim_for_f104_tire.stl

front_rim_for_f104_tire.stl

servo_saver_upper.stl

servo_holder.stl

rear_rim.stl

nose.stl

motor_cover.stl

781.7 KBupdated 16. 5. 2019

355.9 KBupdated 16. 5. 2019

21.4 KBupdated 16. 5. 2019

447.8 KBupdated 16. 5. 2019

526.8 KBupdated 16. 5. 2019

516.5 KBupdated 16. 5. 2019

515.3 KBupdated 16. 5. 2019

311.1 KBupdated 16. 5. 2019

817.8 KBupdated 16. 5. 2019

rainlight_and_diffuser.stl

camera.stl

steering_push_pin.stl

tire_v2.stl

tire.stl

wheel_axle_holder_left.stl

rear_wheel_axle.stl

servo_saver_lower.stl

rear_view_mirror_left.stl

37.4 KBupdated 16. 5. 2019

65.5 KBupdated 16. 5. 2019

225.7 KBupdated 16. 5. 2019

1.4 MBupdated 16. 5. 2019

1.2 MBupdated 16. 5. 2019

817.8 KBupdated 16. 5. 2019

93.8 KBupdated 16. 5. 2019

246.8 KBupdated 16. 5. 2019

58.6 KBupdated 16. 5. 2019

lock_pin.stl

wheel_lock_nut.stl

rear_wing.stl

front.stl

tire-ninjatek.stl

rear_view_mirror_right.stl

pinion_gear.stl

spur_gear.stl

front_lower_bom.stl

259.5 KBupdated 16. 5. 2019

1.2 MBupdated 16. 5. 2019

40.4 KBupdated 16. 5. 2019

3.7 MBupdated 16. 5. 2019

3.3 MBupdated 16. 5. 2019

1.4 MBupdated 16. 5. 2019

116.3 KBupdated 16. 5. 2019

291.9 KBupdated 16. 5. 2019

2.2 MBupdated 16. 5. 2019

wheel_axle_holder_right.stl

center_body.stl

dual_extr_nose_upper.stl

dual_extr_front_lower.stp

dual_extr_lid_lower.stp

dual_extr_front_lower.stl

dual_extr_front-upper.stp

dual_extr_lid_upper.stp

dual_extr_noser_lower.stp

1.4 MBupdated 16. 5. 2019

195.9 KBupdated 16. 5. 2019

54.3 KBupdated 16. 5. 2019

61.7 KBupdated 16. 5. 2019

618.7 KBupdated 16. 5. 2019

42.7 MBupdated 16. 5. 2019

The Author has not uploaded any G-codes.Try to search in User G-codes section or generate and upload yourown.

License

This work is licensed under a Creative Commons (4.0 International License)

dual_extr_lid_lower.stl

dual_extr_lid_upper.stl

dual_extr_front_upper.stl

dual_extr_nose_upper.stp

dual_extr_nose_lower.stl

openrc_f1_assembly.step

Attribution-ShareAlike

✖ | Sharing without ATTRIBUTION ✔ | Remix Culture allowed ✔ | Commercial Use ✔ | Free Cultural Works ✔ | Meets Open Definition