xt30/xt50 programming part 2slide 62 question 1 1) arming modes (programmed in system options)...
TRANSCRIPT
XT30/XT50 PROGRAMMING PART 2
Slide 1 XT30/XT50 Basic Training
Programming- Part 2
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
Slide 2 Objectives
After completing this course you will:
1) Understand how to prepare the panel for programming and how to access the built-in programmer. You will also understand how to navigate the programming menus.
2) Understand how to configure a DMP XT30/XT50 control panel to meet your job requirements.
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
Slide 3 Bell Options
• Define how the bell responds
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
XT30/XT50 PROGRAMMING PART 2
Slide 4 Bell Cutoff Time
• Timer for main bell– 1 to 15 minutes– 0 for continuous
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
Slide 5 Automatic Bell Test
• Yes to ring bell on arming• Closing Wait operation
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
Slide 6 Bell Output
• Output to follow panel bell• Note on Temporal
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
XT30/XT50 PROGRAMMING PART 2
Slide 7 Bell Action Section
• Bell output pattern-N -P-S -T
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
Slide 8 Fire Type Bell Output
• Bell output for fire zones
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
Slide 9 Burglary Type Bell Output
• Bell output for burg zones
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
XT30/XT50 PROGRAMMING PART 2
Slide 10 Supervisory Type Bell Output
• Bell output for supervisory zones
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
Slide 11 Panic Type Bell Output
• Bell Output for panic zones
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
Slide 12 Emergency Type Bell Output
• Bell output for emergency zones
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
XT30/XT50 PROGRAMMING PART 2
Slide 13 Auxiliary 1 Type Bell Output
• Bell output for auxiliary zones
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
Slide 14 Auxiliary 2 Type Bell Output
• Bell output for auxiliary 2 zones
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
Slide 15 Output Options Section
• Define operation of control panel output– Outputs 1 to 4, 31 to 34, 41 to 44– Note on wireless outputs
• Fast response details
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
XT30/XT50 PROGRAMMING PART 2
Slide 16 Cutoff Output
• Specifies outputs to turn off
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
Slide 17 Output Cutoff Time
• Amount of time for output to turn off– 1 to 15 minutes– 0 for continuous
• Bell output for panic zones
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
Slide 18 Communication Failure Output
• Output to activate on comm failure– 0 disables
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
XT30/XT50 PROGRAMMING PART 2
Slide 19 Fire Alarm Output
• Output to activate on fire alarm• Note
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
Slide 20 Fire Trouble Output
• Output to activate on fire trouble
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
Slide 21 Ambush Output
• Output to activate on ambush code• Sensor reset
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
XT30/XT50 PROGRAMMING PART 2
Slide 22 Entry Delay Output
• Output to activate with Entry Delay• Deactivates with disarm or timer expire
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
Slide 23 Exit Delay Output
• Output to activate on Exit Delay• Deactivates on timer or arming process stop
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
Slide 24 Ready Output
• Output to activate on normal zone condition– Deactivates on any bad zone
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
XT30/XT50 PROGRAMMING PART 2
Slide 25 Armed Output Number
• Output to activate on area arming– Deactivate on disarm
• Note
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
Slide 26 Burglary Output
• Output to activate on burg alarm– Deactivates on disarm
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
Slide 27 Late To Close
Output
• Output to activate at Closing Time! display– Deactivates on extend or change
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
XT30/XT50 PROGRAMMING PART 2
Slide 28 Arm-Alarm Output
• Output to activate on any area arming– Pulse on alarm
• Note on wireless outputs
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
Slide 29 XT30/XT50 Output Options Review
The next 9 slides will cover the Output Options section.
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
Slide 30 Question 1
1) The panel's BELL OUTPUT does not turn on for trouble conditions.
TrueFalse
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
XT30/XT50 PROGRAMMING PART 2
Slide 31 Question 1
1) The panel's BELL OUTPUT does not turn on for trouble conditions.
TrueFalse
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
Slide 32 Question 2
2) Selecting YES for the BELL TEST option will cause the panel to turn ___ the BELL OUTPUT for __________ any time all areas have been armed.
A. on, one secondB. off, two secondsC. on, 5 minutesD. on, two seconds
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
Slide 33 Question 2
2) Selecting YES for the BELL TEST option will cause the panel to turn ___ the BELL OUTPUT for __________ any time all areas have been armed.
A. on, one secondB. off, two secondsC. on, 5 minutesD. on, two seconds
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
XT30/XT50 PROGRAMMING PART 2
Slide 34 Question 3
3) Which of the four BELL ACTION options are missing from the following list: Steady, _________, Temporal Code 3, None
A. StrobeB. WhoopC. Pulse D. Optional
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
Slide 35 Question 3
3) Which of the four BELL ACTION options are missing from the following list: Steady, _________, Temporal Code 3, None
A. StrobeB. WhoopC. Pulse D. Optional
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
Slide 36 Question 4
4) Selecting YES for Bell Test also enables the ______________ feature, if
opening/closing reports are enabled.
A. Closing WaitB. Closing ReportC. Closing CodeD. Closing Check
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
XT30/XT50 PROGRAMMING PART 2
Slide 37 Question 4
4) Selecting YES for Bell Test also enables the ______________ feature, if
opening/closing reports are enabled.
A. Closing WaitB. Closing ReportC. Closing CodeD. Closing Check
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
Slide 38 Question 5
5) The ENTRY DELAY output will turn off when the system is disarmed.
TrueFalse
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
Slide 39 Question 5
5) The ENTRY DELAY output will turn off when the system is disarmed.
TrueFalse
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
XT30/XT50 PROGRAMMING PART 2
Slide 40 Question 6
6) The COMM FAIL OUTPUT will turn on when the panel has failed to
communicate with the receiver after __________ dial attempts.
A. 1B. 10C. 4D. 3
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
Slide 41 Question 6
6) The COMM FAIL OUTPUT will turn on when the panel has failed to
communicate with the receiver after __________ dial attempts.
A. 1B. 10C. 4D. 3
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
Slide 42 Question 7
7) The ___________ output is not compatible with the CUTOFF OUTPUT
option.
A. DEVICE FAILB. FIRE ALARM C. PHONE TROUBLED. AREA
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
XT30/XT50 PROGRAMMING PART 2
Slide 43 Question 7
7) The ___________ output is not compatible with the CUTOFF OUTPUT
option.
A. DEVICE FAILB. FIRE ALARM C. PHONE TROUBLED. AREA
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
Slide 44 Question 8
8) Which output will turn on with the keypad message CLOSING TIME! ?
A. LATE TO CLOSEB. AMBUSHC. PHONE TROUBLED. READY
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
Slide 45 Question 8
8) Which output will turn on with the keypad message CLOSING TIME! ?
A. LATE TO CLOSEB. AMBUSHC. PHONE TROUBLED. READY
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
XT30/XT50 PROGRAMMING PART 2
Slide 46 Question 9
9) The _____________ output is commonly used to drive a status LED on a keyswitch
arming system.
A. STEADYB. EXIT DELAYC. ARMEDD. READY
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
Slide 47 Question 9
9) The _____________ output is commonly used to drive a status LED on a keyswitch
arming system.
A. STEADYB. EXIT DELAYC. ARMEDD. READY
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
Slide 48 Output Information
• Wireless output section• Only displays if House Code is not Zero
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
XT30/XT50 PROGRAMMING PART 2
Slide 49 Output Number
• Output range 31 to 34 and 41 to 44• Note
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
Slide 50 Output Name
• Name the output• “Unused” outputs
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
Slide 51 Serial Number
• Wireless device serial number
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
XT30/XT50 PROGRAMMING PART 2
Slide 52 Supervision Time
• Enter supervision time for device– 0, 3, 60 and 240 minutes
• Note on panel reset
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
Slide 53 Area Information Section
• Settings for area systems• Note on naming areas
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
Slide 54 Arming Modes
• Three arming modes– Area– A/P– H/A
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
XT30/XT50 PROGRAMMING PART 2
Slide 55 Area Number Selection
• Select the area to be configured
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
Slide 56 Area Name
• Names activate the area• Clearing a name• Note
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
Slide 57 Automatic Arming
• Schedule automatic arming• Note 1 and Note 2
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
XT30/XT50 PROGRAMMING PART 2
Slide 58 Bad Zone Handling
• How the panel deals with bad zones-Byp -Forc -Ref
• Note
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
Slide 59 Automatic Disarming
• Scheduled automatic disarming• Note 1 and Note 2
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
Slide 60 XT30/XT50 Area Information Review
The next 8 slides will cover the Area Information section.
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
XT30/XT50 PROGRAMMING PART 2
Slide 61 Question 1
1) Arming modes (programmed in SYSTEM OPTIONS) define how the areas will operate and also determines how many _____ are available to use in the system.
A. none of theseB. outputsC. zonesD. areas
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
Slide 62 Question 1
1) Arming modes (programmed in SYSTEM OPTIONS) define how the areas will operate and also determines how many _____ are available to use in the system.
A. none of theseB. outputsC. zonesD. areas
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
Slide 63 Question 2
2) The XT30/XT50 have Auto Arming that takes place at the scheduled CLOSING TIME. If no schedules are entered, how often will the panel automatically arm?
A. every day at midnightB. neverC. every hour D. every 30 minutes
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
XT30/XT50 PROGRAMMING PART 2
Slide 64 Question 2
2) The XT30/XT50 have Auto Arming that takes place at the scheduled CLOSING TIME. If no schedules are entered, how often will the panel automatically arm?
A. every day at midnightB. neverC. every hour D. every 30 minutes
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
Slide 65 Question 3
3) An AREA system allows you to have up to _________________ independent areas.
A. eightB. twoC. threeD. four
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
Slide 66 Question 3
3) An AREA system allows you to have up to _________________ independent areas.
A. eightB. twoC. threeD. four
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
XT30/XT50 PROGRAMMING PART 2
Slide 67 Question 4
4) When the arming mode is HOME/SLEEP/AWAY, how many areas may be armed?
A. 1B. 8C. 3D. 2
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
Slide 68 Question 4
4) When the arming mode is HOME/SLEEP/AWAY, how many areas may be armed?
A. 1B. 8C. 3D. 2
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
Slide 69 Question 5
5) The ALL/PERIMETER mode allows your customers to choose to arm the ________________ area by itself.
PerimeterInterior
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
XT30/XT50 PROGRAMMING PART 2
Slide 70 Question 5
5) The ALL/PERIMETER mode allows your customers to choose to arm the ________________ area by itself.
PerimeterInterior
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
Slide 71 Question 6
6) For XT30 and XT50 panels, the MODE: option allows you to configure the system as an ________________________ system.
A. HOME/AWAYB. ALL/PERIMETERC. AREAD. any of these
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
Slide 72 Question 6
6) For XT30 and XT50 panels, the MODE: option allows you to configure the system as an ________________________ system.
A. HOME/AWAYB. ALL/PERIMETERC. AREAD. any of these
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
XT30/XT50 PROGRAMMING PART 2
Slide 73 Question 7
7) The EXIT DELAY option determines how long your customers have to exit any area that has an ENTRY/EXIT zone.
TrueFalse
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
Slide 74 Question 7
7) The EXIT DELAY option determines how long your customers have to exit any area that has an ENTRY/EXIT zone.
TrueFalse
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
Slide 75 Question 8
8) The BAD ZONES option is where you determine what the panel will do when it encounters a bad zone during ____________.
A. none of theseB. auto arming onlyC. auto disarming onlyD. arming or disarming
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
XT30/XT50 PROGRAMMING PART 2
Slide 76 Question 8
8) The BAD ZONES option is where you determine what the panel will do when it encounters a bad zone during ____________.
A. none of theseB. auto arming onlyC. auto disarming onlyD. arming or disarming
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
Slide 77 Zone Information Section
• Programming for zones– Note
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
Slide 78 Zone Number
• XT30 zones: 10 on board/20 expanded zones• XT50 zones: 10 on board/20 expanded zones
plus 20 additional wireless only
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
XT30/XT50 PROGRAMMING PART 2
Slide 79 Keypad Bus Zone Numbering
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
Slide 80 Key Fob
• Yes to program 1100 Series Key Fob– 31 to 34 – 41 to 44
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
Slide 81 Zone Name
• Name a zone to activate it– Up to 16 characters
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
XT30/XT50 PROGRAMMING PART 2
Slide 82 Zone Type
• Select a zone type– 12 to choose from
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
Slide 83 -- , NT, DY and EX Zone Types*
-Blank-Night-Day-Exit
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
Slide 84 FI, PN, EM and SV Zone Types*
-Fire-Panic-Emergency-Supervisory
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
XT30/XT50 PROGRAMMING PART 2
Slide 85 A1, A2, FV and AR Zone Types*
-Auxiliary 1-Auxiliary 2-Fire Verify-Arming
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
Slide 86 Area Number(non-24 hour zones only)
• Assign zone to proper area
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
Slide 87 Arming Zone STYLES
• Define AR zone operation– Toggle– Arm only– Disarm only
• Note
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
XT30/XT50 PROGRAMMING PART 2
Slide 88 Arming Zone STYLES (cont'd)
• Additional arming zone styles:– Step*– Maintain
• Note
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
Slide 89 Next Zone?
• Yes for a different zone• No to continue with current zone
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
Slide 90 DMP Wireless Programming
• Select NO to enter wireless programming
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
XT30/XT50 PROGRAMMING PART 2
Slide 91 Transmitter Programming
• Select Yes for wireless device• Enter devices serial number• Already used prompt
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
Slide 92 Contact
• Select Internal or External– Normally open (No Yes) for external
contacts• Note
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
Slide 93 Contact (cont.)*
• Prompt for 1114 zone expander• Select contact to program
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
XT30/XT50 PROGRAMMING PART 2
Slide 94 Supervision Time
• Select supervision time– 240 default– 0, 3, 60, or 240 minutes
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
Slide 95 LED Operation
• Yes to enable LED operation
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
Slide 96 Next Zone
• Yes to return to “Zone No:”• No for Alarm Action
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
XT30/XT50 PROGRAMMING PART 2
Slide 97 1100 Series Key Fobs
• Key Fob programming• The following slides cover programming
when Key Fob YES is selected
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
Slide 98 Key Fob User Number
• User number to associate with button
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
Slide 99 Key Fob Serial Number
• Enter 8 digit serial number• If serial number has already been
programmed, “Already Used” displays
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
XT30/XT50 PROGRAMMING PART 2
Slide 100 Key Fob Supervision Time
• Enter time in minutes• Default is zero
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
Slide 101 Number of Key Fob Buttons
• Enter number of buttons on Fob Being used
• Default is four• Note on one button Fobs
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
Slide 102 Key Fob Button
SelectionFour Buttons
• Prompt for a four button Fob• Select button to program
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
XT30/XT50 PROGRAMMING PART 2
Slide 103 Key Fob Button
SelectionTwo Buttons
• Prompt for two button Fob– Select button to program
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
Slide 104 Button Action
• Assignable action for Key Fob buttons:-Arm -Disarm -Toggle Arm -Status• Continued on next slide
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
Slide 105 Button Action (cont.)
-Panic -Panic 2 -Emerg -Emerg 2-Output -Sensor Reset -Unused
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
XT30/XT50 PROGRAMMING PART 2
Slide 106 Button Press Time
• Amount of time button must be pressed– Short - half second– Long – 2 seconds
• Note on zone type unaffected by this
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
Slide 107 Arm/Disarm Area Selection
• Enter areas to be armed by Key Fob*Varies by arming mode*
--Area system 1,2,3,4 --A/P- Perim or All--H/S/A- Home Sleep Away
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
Slide 108 Output Number
• Assign relay to Key Fob button– Range 1 to 4, 31 to 34 and 41 to 44
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
XT30/XT50 PROGRAMMING PART 2
Slide 109 Output Action
• Actions available:-STD -PLS -MOM-TGL -OFF
• Note on output operation
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
Slide 110 ALARM ACTION
• Customize any zone type• Non 24 hour zone start with Disarmed Open• 24 hour zones start with Armed Open• Note
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
Slide 111 ZONE CONDITIONS
• Four zone conditions -DO -DS -AO -AS
• Each has three actions-Message -Output number -Output Action
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
XT30/XT50 PROGRAMMING PART 2
Slide 112 MESSAGE (Report to Transmit)
• Messages-Alarm -Trouble-Local -dash
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
Slide 113 Activate Output Number?
• Enter output activated by a zone condition
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
Slide 114 Output Action
• Behavior of output on activation-Steady -Pulse-Momentary -Follow
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
XT30/XT50 PROGRAMMING PART 2
Slide 115 Swinger Bypass?
• Select Yes to allow bypass• How does it work?
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
Slide 116 Prewarn Address
• Address of keypad to tone on Entry
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
Slide 117 Entry Delay?
• Select Entry Delay 1 or 2
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
XT30/XT50 PROGRAMMING PART 2
Slide 118 Cross Zone?*
• Yes to enable cross zoning• How does it work?
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
Slide 119 PRIORITY Zone?
• Yes to make this a priority zone• Uses?
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
Slide 120 Zone Number?
• Enter next zone number
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
XT30/XT50 PROGRAMMING PART 2
Slide 121 XT30/XT50 Zone Information Review
The next 9 slides will cover the Zone Information section.
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
Slide 122 Question 1
1)Entering a 'space' in the zone name is achieved by pressing __________ then the __________ select key.
A. zero, firstB. 9, thirdC. command, anyD. 9, first
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
Slide 123 Question 1
1)Entering a 'space' in the zone name is achieved by pressing __________ then the __________ select key.
A. zero, firstB. 9, thirdC. command, anyD. 9, first
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
XT30/XT50 PROGRAMMING PART 2
Slide 124 Question 2
2)The four zone conditions are:
A. DO, DS, AO, ASB. NO, YES, AM, PMC. DM, PM, DT, DS
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
Slide 125 Question 2
2)The four zone conditions are:
A. DO, DS, AO, ASB. NO, YES, AM, PMC. DM, PM, DT, DS
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
Slide 126 Question 3
3) A 16-zone expander on the keypad bus is addressed 02. What would be the zone number for the FIFTH zone on this expander?
A. 25B. 32C. 31D. 24
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
XT30/XT50 PROGRAMMING PART 2
Slide 127 Question 3
3) A 16-zone expander on the keypad bus is addressed 02. What would be the zone number for the FIFTH zone on this expander?
A. 25B. 32C. 31D. 24
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
Slide 128 Question 4
4) Alarm Action prompts for 24-hour zones begin with _______________.
A. ZONE NO:-B. ARMED OPENC. DISARMED OPEND. NEXT ZONE? NO YES
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
Slide 129 Question 4
4) Alarm Action prompts for 24-hour zones begin with _______________.
A. ZONE NO:-B. ARMED OPENC. DISARMED OPEND. NEXT ZONE? NO YES
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
XT30/XT50 PROGRAMMING PART 2
Slide 130 Question 5
5) On a XT30/XT50, zones at address #1 are numbered _____________.
A. 7 - 10B. 11 - 14C. 1 - 10D. 21 - 24
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
Slide 131 Question 5
5) On a XT30/XT50, zones at address #1 are numbered _____________.
A. 7 - 10B. 11 - 14C. 1 - 10D. 21 - 24
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
Slide 132 Question 6
6) When ____________ is set to YES, this zone may not be bypassed.
A. DayB. PriorityC. Auxiliary 2D. Arming
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
XT30/XT50 PROGRAMMING PART 2
Slide 133 Question 6
6) When ____________ is set to YES, this zone may not be bypassed.
A. DayB. PriorityC. Auxiliary 2D. Arming
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
Slide 134 Question 7
7) Swinger bypass set to YES allows the zone to be bypassed by the panel after one alarm, trouble, or local trip within _______.
A. 30 minutesB. ten minutesC. one hourD. five minutes
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
Slide 135 Question 7
7) Swinger bypass set to YES allows the zone to be bypassed by the panel after one alarm, trouble, or local trip within _______.
A. 30 minutesB. ten minutesC. one hourD. five minutes
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
XT30/XT50 PROGRAMMING PART 2
Slide 136 Question 8
8) Which zone type has the option to set a PREWARN address?
A. SupervisoryB. Fire VerifyC. Exit typeD. all of these
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
Slide 137 Question 8
8) Which zone type has the option to set a PREWARN address?
A. SupervisoryB. Fire VerifyC. Exit typeD. all of these
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
Slide 138 Question 9
9) When zone's Message is set to LOCAL, reports are sent to the receiver.
TrueFalse
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
XT30/XT50 PROGRAMMING PART 2
Slide 139 Question 9
9) When zone's Message is set to LOCAL, reports are sent to the receiver.
TrueFalse
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
Slide 140 Stop Section
• Stop to exit programming– Several events occur
• Power up
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
Slide 141 Set Lockout Code
• Security code for programming– 1 to 65535 range (1 to 5 digits)
• Remote Link
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
XT30/XT50 PROGRAMMING PART 2
Slide 142 Enter Lockout Code
• Setting lockout code• Deleting lockout code
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
Slide 143 XT30/XT50 STOP & Lockout Code
ReviewThe next 5 slides will cover the STOP &
Lockout Code section.
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
Slide 144 Question 1
1) The STOP routine exits the programmer mode and prepares the panel for normal operation.
TrueFalse
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
XT30/XT50 PROGRAMMING PART 2
Slide 145 Question 1
1) The STOP routine exits the programmer mode and prepares the panel for normal operation.
TrueFalse
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
Slide 146 Question 2
2) The STOP routine will do the following:
A. turn off all outputsB. clear the status listC. disarm all areasD. all of these
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
Slide 147 Question 2
2) The STOP routine will do the following:
A. turn off all outputsB. clear the status listC. disarm all areasD. all of these
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
XT30/XT50 PROGRAMMING PART 2
Slide 148 Question 3
3) Initialization will clear all codes, including the lockout code.
TrueFalse
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
Slide 149 Question 3
3) Initialization will clear all codes, including the lockout code.
TrueFalse
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
Slide 150 Question 4
4) The SET LOCKOUT CODE will allow you to enter a security code that must be entered to get into the panel's programming mode.
TrueFalse
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
XT30/XT50 PROGRAMMING PART 2
Slide 151 Question 4
4) The SET LOCKOUT CODE will allow you to enter a security code that must be entered to get into the panel's programming mode.
TrueFalse
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
Slide 152 Question 5
5) The LOCKOUT CODE can be from ________________ digits.
A. 1 to 5B. 1 to 8
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
Slide 153 Question 5
5) The LOCKOUT CODE can be from ________________ digits.
A. 1 to 5B. 1 to 8
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
XT30/XT50 PROGRAMMING PART 2
8/08
Slide 154 CONGRATULATIONS!
You have completed the XT30/XT50 Programming course.
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
___________________________________
LT-1006 © 2008 Digital Monitoring Products, Inc.