x:panda tm - r82, inc. · 2016-11-16 · g b safety the x:panda has earned the ce-mark. this...

English manual

GB

11.2016 - rev. 016

TMx:panda

© 2012 R82 A/S. All rights reserved.The R82 logo and the x:panda chairs are trademarks of R82 A/S.

Pat. pend.U.S. Patent Des. D598,680 SPat. Pend.

GB

X:PANDAx:panda is a multiadjustable seat, delivered in 4 different sizes. Each seat adjusts in 3 different widths and stepless in seat depth.

The back is dynamic, making it possible for the child to extend and push back against relatively light resistance and then recover into the desired sitting position. Furthermore the back angles to make it possible to place the child with either an open or closed hip angle. When angling the seat and the base it is possible to create the desired working or resting position.

The many adjustment possibilities and wide range of accessories makes it possible to adjust the seat to an individual child’s need for comfort and support.

The seat fits on a variety of seat bases from R82, making it suitable for both indoor and outdoor use.

Indoor use High-low:x indoor frame

Outdoor use High-low:x outdoor frame Combi Frame Serval Buggy frame

This manual will enable you to take full advantage of the many possibilities of the x:panda. Therefore, we recommend that you read this manual before using the frame.

GB

2

GB

GB CONTENTSSafety ..................................................................................................................4Tools ....................................................................................................................4Warranty ..............................................................................................................4Ready for use ......................................................................................................5Back recline .........................................................................................................6Back height adjustment .......................................................................................6Hip supports - Individual adjustment ...................................................................7Leg supports - individual adjustment ...................................................................7Head supports .....................................................................................................8Back width extension ...........................................................................................8Fixed side supports .............................................................................................9Quick locks for fixed side supports ......................................................................9Upper arm support for the fixed side supports ...................................................9Swing-away side supports .................................................................................10Quick locks for swing-away side supports .........................................................10Arm rest .............................................................................................................11Tray, swing-away ...............................................................................................12Tray, two-rod system .........................................................................................12Arm rest for tray .................................................................................................13Toybar for tray....................................................................................................13Grip handle for tray ............................................................................................13Vests & belts ......................................................................................................14Fixlock fittings ....................................................................................................14Seat wedges ......................................................................................................15Seat strap ..........................................................................................................15Foam back plate ................................................................................................16Cover plate ........................................................................................................16Lumbar support .................................................................................................16Non-dynamic gas spring ....................................................................................17Fixed rod............................................................................................................17x:panda mounted on High-low:x ........................................................................18Mounting the seat on the High-low:x size 3 ......................................................19Growth from one size to another - width adjustment ........................................20Growth from one size to another - depth adjustment .......................................21Replacement of back - one size to another .......................................................22The x:panda seat on High-low:x frames ............................................................23The x:panda seat on Panda Fututra High-low frames .......................................24The x:panda seat on Combi Frame:x ................................................................25The x:panda seat on buggy frame .....................................................................26Transportation in motor vehicles .......................................................................27Position the back before transportation .............................................................28Transport fittings on a buggy frame ...................................................................28Transport fittings on the Combi Frame:x ...........................................................29Secure the product in the vehicle ......................................................................30Secure the child in the Product..........................................................................31Product identification .........................................................................................32Product identification .........................................................................................33Measurements ...................................................................................................34Technical data....................................................................................................35Producer ............................................................................................................35Distributor ..........................................................................................................35Maintenance ......................................................................................................36

3

GB

SAFETYThe x:panda has earned the CE-mark. This certifies that it meets all relevant European safety requirements.The durability of this product is 5 years when it is used on a daily basis. Hereafter the product must be renovated (by R82 personnel) to extend the lifetime.

Remove the CE-mark, when rebuilding the product or when using other than original R82 spare parts and fittings.

The x:panda is constructed for one user only. Do not place more than one user in the x:panda.

Never leave your child unattended in this product. Ensure constant supervision by an adult. Incorrect use of the product, may cause serious injury to the user. Ensure that the belt is securely fixed to the product before every use.

Any adjustments and addition of accessories which are not described in this manual, must only be made by authorized R82 personnel. Vests and belts must be mounted according to the instruction provided with the products.

The latest version of the manual is always available online: www.R82.com

GB

GB

TOOLSUse the 5 mm Allen key placed beneath the seat unit, to perform all adjustments described in this manual.

GB

WARRANTYR82 offers a 2-year warranty against defects in workmanship and materials. The warranty would be adversely affected if the customer’s responsibility of servicing and/or daily main-tenance is not carried out according to the guidelines and intervals prescribed by the sup-plier and/or stated in the manual. For further information, we refer to the R82 homepage/download. The warranty can only be sustained if the R82 product is in use in the same country where it was purchased and if the product can be identified by the serial number. The warranty does not cover accidental damage, including damage caused by misuse or neglect. The warranty does not extend to non-durable parts, which are subject to normal wear and tear and need periodic replacement. The warranty is null and void if non-original R82 parts/accessories are used, or if the product is repaired or altered by anyone other than an authorised R82 representative or by trained personnel officially recognised by R82 for repair and maintenance of R82 products. R82 reserves the right to inspect the product being claimed for and the relevant documentation before agreeing to the warranty claim, and to decide upon whether to replace or repair the defective product. It is the customer’s responsibility to return the item being claimed for under warranty to the address of purchase. The warranty is given by R82 or, subsequently, an R82 dealer.

4

D

A

B

C

GB

READY FOR USEThe x:panda is delivered so that it takes up minimum space during transport. Follow the instructions below to unpack the x:panda.

* Remove the x:panda from the box

* Adjust the back angle (A)

* Adjust the back height (B)

* Adjust the seat depth (C)

* Adjust the leg angle (D)

Further instructions can be found on page 6+7. The x:panda is now ready for use once you have fully read this manual.

GB

5

A

B

A

B

D

C

GB

GB

GB

BACK HEIGHT ADJUSTMENT

Loosen the bolts (A) and (B) to adjust the height of the back.

Fasten all bolts at the desired height.

Do not remove any of the bolts - only loosen to adjust.

BACK RECLINERelease the handle (A) to recline the back.

Firmly grab hold and support the back of the chair before releasing the handle to prevent sudden recline.

The release handle is equipped with a security lock (B). Turn the lock to the left and it is acti-vated, turn it to the right and it is deactivated.

Always activate the lock after adjustment.

The back on x:panda has dynamic movement. Move the small ring (C) up or down to adjust the range of movement.

When reclining the back, please be carefull not to get fingers caught between the gas spring and the seat (D).

i

6

A

B

A

GB

GB

GB

LEG SUPPORTS - INDIVIDUAL ADJUSTMENT

Angle and depth adjustment:Loosen the bolt (A) to adjust. Fasten at the de-sired position.

Width adjustment:Remove the bolt (B) to adjust. Fasten at the desired position.

Do not remove any of the bolts (A) - only loosen to adjust.

HIP SUPPORTS - INDIVIDUAL ADJUSTMENT

Angle, depth and width adjustment:Loosen the bolts (A) to adjust. Fasten at the desired position.

Do not remove any of the bolts - only loosen to adjust.i

i

7

A

D

CB

AGB

GB HEAD SUPPORTSMounting and height adjustment:Loosen the handle (A).

Angle adjustment:Loosen the screws (B) and (C) with a spanner.

Sideways adjustment:Loosen the screw (D).

Fasten all screws at the desired position.

When adjusting the head support, please be carefull not to get fingers caught bet-ween the back of the chair and the head support fiitting.

BACK WIDTH EXTENSION

ONLY SIZE 4

Mount the back width extension and fasten the screws (A) on the back. Make sure the extension is pushed all the way in before fastening.

GB

8

A

A

B GB

GB FIXED SIDE SUPPORTS

Height adjustment:Remove the bolts (A). Place the supports in the desired position and remount the bolts.

Width adjustment:Loosen the bolts (A). Fasten at the desired position.

GB QUICK LOCKS FOR FIXED SIDE SUPPORTS

Height adjustment:Remove the bolts (A).Place the side supports with quick locks in the desired position and remount the bolts.

Width adjustment:Pull the quick lock handle up (B). Lock the handle down when the support is in the desired position.

UPPER ARM SUPPORT FOR THE FIXED SIDE SUPPORTS

The upper arm supports is developed as an accessory to seats produced later than De-cember 2008, i.e. for seats delivered before this period, you will need a new set of side supports in order to mount the upper arm supports.

GB

9

A

A

B

B

GB

GB SWING-AWAY SIDE SUPPORTS

Height adjustment:Remove the bolts (A). Place the supports and remount the bolts.

Width adjustment:Loosen the bolts (A). Fasten at the desired position.

Swing-away function:Press the red button (B) to release.

The carer should check and oil (synthetic oil) the swing away parts occationally - at least every 3 months.

GB QUICK LOCKS FOR SWING-AWAY SIDE SUPPORTS

Height adjustment:Remove the bolts (A).Place the side supports with quick locks and remount the bolts.

Width adjustment:Pull the quick lock handle up (B). Lock the handle in the desired position.

10

B

A

C

D

C

D

B

D

GB

GB ARM RESTHeight adjustment:Loosen the screw (A) and move it into desired height position. Fasten the screw.Loosen handle/screw (C) to move the arm rest into position. Fasten the handle/screw (hand-tight).

Angling the arm rest cushion:Loosen the handle (B).

Angling the arm rest bar (only size 1+2+3):Loosen the handle/screw (C).

Adjust the arm rest cushion:Loosen the screws (D) beneath the armpad.

When adjusting the arm rest, please be carefull not to get fingers caught between the chair and the armpad.

Size 1+2+3

Size 4

Size 4

11

A

C

B

A BC

GB

GB TRAY, SWING-AWAYONLY FOR SIZE 1+2+3

A) Mounting and depth adjustment

B) Width adjustment

C) Angling the tray, by angling the arm rests.

The tray can only be mounted on a x:panda equipped with arm rests.

GB TRAY, TWO-ROD SYSTEM

ONLY FOR SIZE 1+2+3

A) Mounting and depth adjustment

B) Width adjustment

C) Angling the tray, by angling the arm rests.

The tray can only be mounted on a x:panda equipped with arm rests mounted at the same height and angle.

12

A

B

A

A

GB

GB ARM REST FOR TRAY

ONLY FOR SIZE 1+2+3

A) Depth adjustment

B) Angle adjustment

The arm rests can only be mounted on a x:panda equipped with tray.

GB TOYBAR FOR TRAYONLY FOR SIZE 1+2+3

A) Angle ajdustment

The toybar can only be mounted on a x:panda equipped with tray.

GB GRIP HANDLE FOR TRAY

ONLY FOR SIZE 1+2+3

A) Angle adjustment

The grip handle can only be mounted on a x:panda equipped with tray.

13

A

A

C

A

BC

D

B

GB

GB VESTS & BELTSAll vests and belts with 25 mm strap can be mounted on the seat. We recommend to use the fixlocks or belt guidances on the chair.

Fixlocks:Use the fixlock (A) mounted on the chair to fa-sten and adjust all vests and belts. An extra 40 mm fixlock can be mounted on the size 4 seat if needed (B).

Belt guidance:Guide the beltstraps through the prepared slots (C) in the seat.

FIXLOCK FITTINGSTo mount vests and belts the correct way, it might be necessary to mount extra fixlock fittings. The fittings are mounted on the top of the back and are able to lift the straps away from the shoulders of the user.

* Mount the fittings in the lower holes (A) to get a higher mounting of the straps.

* Mount the fittings in the top holes (B) to get a lower mounting of the straps.

* Mount the fittings as shown on drawing (C) to get a larger distance between the fittings.

* Mount the fittings as shown on drawing (D) to get a smaller distance between the fittings.

GB

14

A

GB

SEAT WEDGESDepth adjustment:Remove the seat cushion and release the wed-ges from the velcro in the seat.

Flip up the velcro (A) and place the wedges at the desired depth position. Replace the seat cushion.

GB

SEAT STRAPDepending on the desired leg abduction the seat strap is mounted in one of the three holes in the seat.

Adjustment:Flip up the strap in one of the sides and adjust the length of the strap. Fold down the strap to fasten with the velcro.

GB

15

GB

FOAM BACK PLATEThe foam back plate can be adjusted to fit the gap beneath the back.

* If necessary, cut the foam plate with a knife to make it fit the gap.

* Place the foam plate on the back.

GB

LUMBAR SUPPORTRemove the cushion to mount the lumbar sup-port on the back

* Place the lumbar support in position

COVER PLATEONLY FOR SIZE 4

The cover plate fits the gap beneath the back.

* The cover plate is mounted in the slot in the back

GB

GB

16

A

B

GB

NON-DYNAMIC GAS SPRING

ONLY FOR SIZE 1+2+3

The standard gas spring can be replaced with a non-dynamic gas spring.

Loosen the handle (A) to angle the back.

Please be aware not to get your fingers caught betweeen the gas spring and the seat when angling (B).

GB

FIXED RODThe standard gas spring can be replaced with a fixed rod.

GB

17

A

B

GB

GB X:PANDA MOUNTED ON HIGH-LOW:X

To mount the seat:

The interface and the footrest bar must be replaced on the old High-low frames.

Place the seat adapter in the interface and push it all the way back, until it "clicks" into place.Lock the red handle (B) to secure the stability of the seat.

Do not use the first hole it „clicks” into. This is just the „safety hole” which will „catch” the seat if the knob accidently should pop out of its correct hole.

To dismount the seat: Unlock the red handle (B). Pull out the knob (A), pull the seat forward, and lift at the same time.

18

A

2 x2 x

GB

MOUNTING THE SEAT ON THE HIGH-LOW:X SIZE 3

ONLY SIZE 3+4 Mount the x:panda seat directly on the High-low:x size 3 frame.

* Lead the enclosed screws though the seat frame (A) from below. Make sure the seat is securely fastened before use.

* Remove the screws at dismounting

GB

19

A

B

C

F

D

E

E

Size 1+2+3

Size 4

GB

GROWTH FROM ONE SIZE TO ANOTHER - WIDTH ADJUSTMENT

Follow this description to perform a smooth adjustment of the seat width. Also read the in-structions on the next page concerning depth adjustment.

Dismount the hip supports (A) at both sides.Dismount the metalplate (B). Remove the 4 bolts (C) and swing away the back.

Left chair side:Pull the leg support forward but do not remove any bolts not described.

Remove the bolt (D).Remove the bolt (E).

Remount at the desired width position and re-place the bolts (D) and (E). Do not fasten the bolts completely.

Right chair side:Remove the bolts (D) and (E) at the opposite side of the chair.

Place the seat spacer (F).

Remount at the same width position as the op-posite side and replace the bolts (D) and (E).

Remount the bolts (C).

Both chair sides:Fasten all bolts (C) (D) and (E) at both sides of the seat.

Do not loosen or remove any bolts not described above.

To prevent at mix up of bolts, we re-commend to keep the removed bolts together with the removed part, e.g. the hip supports.

The carer should check and tighten all bolts at least every month.

GB

20

A

B

GB

GB GROWTH FROM ONE SIZE TO ANOTHER - DEPTH ADJUSTMENT

Follow this description to perform a smoothly adjustment of the seat depth. Also read the in-struction on the previous page concerning width adjustment.

Remove the two bolts (A) at both sides of the chair.

Take a firm hold of the backrest.

Remove the two bolts (B).

Remount at the desired depth position and re-place and fasten the bolts (A) and (B).

Do not loosen or remove any bolts not described above.

To prevent at mix up of bolts, we re-commend to keep the removed bolts seperated.

The carer should check and tighten all bolts at least every month.

21

D

E

A

B

BC

GB

REPLACEMENT OF BACK - ONE SIZE TO ANOTHER

Loosen the two bolts (A)

Remove the two cross-point screws (B)

Remove the six bolts (C) Remove the cover plate

Remove the back stop device (D) (only size 1+2+3). Pull up the back plate (E) and remove.

Replace the desired back plate (E) and push it all the way down.

Remount the back stop device (D) (only size 1+2+3).

Remount the cover plate.Fasten the 6 bolts (C)

Remount the two cross-point screws (B).

Fasten the two bolts (A).

Finally check that the back moves smoothly up and down.

GB

22

GB

THE X:PANDA SEAT ON HIGH-LOW:X FRAMES

The x:panda seat adjusts in 3 different widths. Each seat in each width can be mounted on different sizes of High-low:x frames. Please see the chart below to find the right size frame for your seat.

● Recommended○ Possible

GB

x:panda High-low:x

indoorsize 1

x:panda High-low:x

indoorsize 2

x:panda High-low:x

indoorsize 3

x:panda High-low:x

outdoorsize 1

x:panda High-low:x

outdoorsize 2

Gas Pow Gas Pow Hyd Pow Gas Pow Gas Pow Hyd

x:panda size 1S ● ● ● ●x:panda size 1M ● ● ● ●x:panda size 1L ● ● ● ●


x:panda size 3S ○ ○ ○ ● ● ● ●x:panda size 3M ○ ○ ○ ● ● ● ●x:panda size 3L ○ ○ ○ ● ● ● ●

x:panda size 4S ●x:panda size 4M ●x:panda size 4L ●

23

GB

THE X:PANDA SEAT ON PANDA FUTUTRA HIGH-LOW FRAMES

Mount a new interface on the High-low frames to mount the x:panda seats. Follow the instruction which follow the interface.

GB

Panda FuturaHigh-low indoor

size 1

Panda FuturaHigh-low outdoor

size 1

Gas Pow Gas Pow



24

GB

THE X:PANDA SEAT ON COMBI FRAME:X

The x:panda seat adjusts in 3 different widths. Each seat in each width can be mounted on different sizes of Combi frames. Please see the chart below to find the right size frame for your seat.

● Recommended○ Possible

GB

Combi Frame:x size 1 Combi Frame:x size 2 Combi Frame:x size 3 Combi Frame:x size 4

20” 22” 24” 12½" 20” 22” 24” 12½" 20” 22” 24” 12½" 20” 22” 24” 12½"

x:panda size 1S ● ● ● ● ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○x:panda size 1M ● ● ● ● ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○x:panda size 1L ● ● ● ● ● ○ ○ ○ ○ ○ ○ ○ ○

x:panda size 2S ● ● ● ● ● ● ● ● ○ ○ ○ ○ ○ ○ ○ ○x:panda size 2M ● ● ● ● ● ● ● ● ● ○ ○ ○ ○x:panda size 2L ● ● ● ● ● ● ● ● ○ ○ ○ ○

x:panda size 3S ● ● ● ● ● ● ● ● ● ● ● ●x:panda size 3M ● ● ● ● ● ● ● ●x:panda size 3L ● ● ● ● ●


25

GB

THE X:PANDA SEAT ON BUGGY FRAME

The x:panda seat adjusts in 3 different widths. Each seat in each width can be mounted on different sizes of buggy frames. Please see the chart below to find the right size frame for your seat.

GB

Buggy frameServalsize 1

Buggy frameServalsize 2

Buggy frameStingray

x:panda size 1S ● ● ●x:panda size 1M ● ● ●x:panda size 1L ● ●

x:panda size 2S ● ● ●x:panda size 2M ● ●x:panda size 2L

x:panda size 3S

x:panda size 3M

x:panda size 3L

x:panda size 4S

x:panda size 4M

x:panda size 4L

26

GB

The chair is approved according to ISO 7176/19-2001 and 16840-4:2009.

x:panda seat is approved for transporting the user in motor vehicles. Please look at MEASURES in the back of this manual for the max load. indication.

The approval is not valid on specially made chairs and frames.

The user should transfer to the vehicle seat and use the vehicle-installed restraints system whenever possible.

Seat and frame must be placed in a for-ward-facing position, when used as a seat in a motor vehicle. Use an approved 4-point strap-type tiedown system according to ISO 10542-2.

Use an approved 3-point belt according to ISO 10542-1 in the wheelchair. Restraints should not be held away from the body by wheelchair components such as armrests or wheels. It is NOT enough only to use a hipbelt or vests and belts not approved by ISO 10542.

The front wheels need to be turned under the frame so as to be in line wit the frame before fixation.

All accessories must be removed from the wheelchair and secured separately in the vehicle. Accessories which can not be rem-oved out of consideration of the user, must be secured to the wheelchair but positioned away from the user with energy-absorbing padding placed between the accessories and the user.

The product should be inspected by the dealer before re-use following involvment in any type of vehicle collison.

The following instructions on how to pre-pare the seat and frame, must be carried out before transportation.

GB

Restraints should not be held away from body by wheelchair

components such as armrests or wheels

TRANSPORTATION IN MOTOR VEHICLES

The x:panda seat on a R82 frame, is approved for transporting users in motor vehicles, when the chair and frame are placed in forward-facing position.

Detailed information about configurations for frames and x:panda seat, max. load/user weight and transportation can be found in the overview "frame_and_seat_combination.pdf". The overview can be found here: http://www.r82.org/media/102124/frame_and_seat_combination.pdf

All information in this chapter must be carried through to maintain safety.

i

27

A

B

B

A

GB

GB POSITION THE BACK BEFORE TRANSPORTATION

The bush (A) on the gasspring (B) must be hand-tightened up against the gasspring house before transportation.

The back MUST be placed in vertical position and the bush (A) MUST be hand-tightened before transportation.

TRANSPORT FITTINGS ON A BUGGY FRAME

Secure the x:panda seat on a buggy frame in a vehicle:

* Mount the 4-point strap-type tiedown system in the vehicle. (Follow the manufactures

instructions)* Mount the two fittings (A) with the symbol (B)

on both sides of the pushchair frame.* Secure the chair to the vehicle, using the 4-

point strap-type tiedown system. Use either a hook or a strap in the fitting (A).

Use a 4-point strap-type tiedown system approved according to ISO 10542-2 or SAE J2249.

GB

28

2 x 2 x

BA C

A

D

BGB

TRANSPORT FITTINGS ON THE COMBI FRAME

Placing the Combi Frame in the vehicle:1. By use of a 4-point strap system, the frame

is secured in the vehicle. (Follow instructions from the manufacturer of the vehicle).

A 4-point strap-system, approved accor-ding to ISO 10542-2 or SAEJ2249, must be used.

On the rear of the frame, fitting A:2. * Remove the plugs. * Place the fittings (A) on the rear bar. * Mount with the enclosed 6 mm long bolts

and nuts. (Note the placement for the different sizes.)

On the front of the frame, fitting B:3. * Remove the plugs (D) in the side rails. * Slide the thread block into the side rails. * Mount the plugs (D) again. * Place the fitting (B) over the thread block. * Tighten with the enclosed 6 mm. bolts and

washer through the holes in the thread block. It is important that the 'legs' on the fitting (B) is placed in the holes in the side rails.

The fitting (B) can be turned upwards (as on the drawing) or downwards if you wish.

4. The wheelchair is fastened in the vehicle by

use of a 4-point strap-system. Either a hook or a strap can be used for fastening the fittings (A) and (B).

Stick the enclosed stickers (C) on the four fittings (A) and (B).

GB

Size 1+2 Size 3+4

29

B15° 15°

30°

1,2 m

65 cm40 cm

GB

GB SECURE THE PRODUCT IN THE VEHICLE

* Mount the 4-point strap-type tiedown sy-stem in the vehicle. (Follow the manufacture

instructions)

* Secure the pushchair to the vehicle, using the 4-point strap-type tiedown system. Use either a hook or a strap in the fitting.

Use a 4-point strap-type tiedown system approved according to ISO 10542-2 and SAE J2249.

Position inside vehicle:

* Remove all accessories from the pushchair before transportation.

* Place the child in forward-facing position.

Be aware of the recommended safety zone when moving children in vehicles.

30

55°

GB

SECURE THE CHILD IN THE PRODUCT

* Mount a hip-belt in the belt fittings in the seat and fasten the user.

* Use the 3-point belt as shown on drawing to secure the user. The belt restraints should be adjusted as tightly as possible, consistent with user comfort. Further the belt webbing should not be twisted when in use.

Use a hip-belt and an approved 3-point belt according to ISO 10542-1 or SAE J2249.

GB

31

A

B

A

B

AB

A

B

B

A

A B XXXXXXDMR ver.: XXXXArt. no.: XXXXXXXProduct: XXXXXXX - Size X

Max load: xxx kgMax load: xxx kg

(XX)XXXXXXXXXXXXXX(XX)XXXXXX(XX)XXXXXX

GB

PRODUCT IDENTIFICATION

x:panda seatA) Serial number The label is placed in the seat under the

cushion to the left.

B) Manufacturer The label is places in the seat under the

cushion to the right.

High-low:x indoor and outdoor frameA) Serial number The label is placed on the left side of the frame.

B) Manufacturer The label is placed on the left side of the frame.

Combi Frame:xA) Serial number The label is placed left on the front cross bar

beneath the seat. B) Manufacturer The label is placed far left on the front cross

bar beneath the seat.

Pushchair frameA) Serial number The label is placed on the top cross bar below

the seat.

B) Manufacturer The label is placed on the cross bar at the left

rear wheel.

GB

32

XXXXXXDMR ver.: XXXXArt. no.: XXXXXXXProduct: XXXXXXX - Size X

Max load: xxx kgMax load: xxx kg

(XX)XXXXXXXXXXXXXX(XX)XXXXXX(XX)XXXXXX

A B

AB

B A

BA

GB

PRODUCT IDENTIFICATION

Multi FrameA) Serial number The label is placed left on the front cross bar



Multi Frame:xA) Serial number The label is placed left on the front cross bar



Strong BaseA) Serial number The label is place on the underside of the

frame to the left.

B) Manufacturer The label is place on the underside of the

frame to the left.

GB

33

160, 200, 240 200, 240, 280 260, 310, 360 340, 400, 460(6¼,7¼,9¼") (7¼,9¼,11") (10¼,12,14") (13¼, 15½, 18")70, 90, 110 100, 120, 140 120, 145, 170 130, 190, 250(2¾, 3½, 4¼") (4, 4¾, 5½") (4¾, 5¾, 6¾") (5, 7½, 9¾")160-260 (6¼-10¼") 220-330 (8½ -12¾") 260-390 (10¼-15¼") 380-530 (14¾-20½")270-370 (10½-14½") 320-420 (12½-16½") 350-470 (13½-18¼") 490-680 (19-26½")230 (9") 280 (11") 330 (12¾") 350 +50 (13½ +2")310, 350, 390 380, 420, 460 470, 520, 570 590, 650, 710(12, 13½, 15¼") (14¾, 16¼, 18") (18¼, 20¼, 22¼") (23, 25¼, 27½")-5° - +30° -5° - +30° -5° - +30° -5° - +30°0° - 15° * 0° - 15° 0° - 15° 0° - 15°0° - 8° - - -

6,5 kg (14,5 lb) 8,5 kg (18,5 lb) 11 kg (28,5 lb) 13 kg (28,5 lb) 45 kg (99 lb) 50 kg (110 lb) 60 kg (132 lb) 80 kg (176 lb)45 kg (99 lb) 50 kg (110 lb) 57 kg (125,5 lb) 57 kg (125,5 lb)

GB

GB MEASUREMENTSx:pandaSize 1mm (inch)

x:pandaSize 2mm (inch)



Seat width (A)

Width, thighs (A1)

Seat depth (B)Back height (C)Back width, top (F)Total width, both legs in max abduction (G)

Back angle (a)Abduction angle, each leg (a1)* size 1 in the smallest position

WeightMax load / user weight onMax load / user weight at transportation

Further information regarding max. load/user weight and transportation:www.R82.com/files/archive/Publications/Pdf/Chart_transport.pdf

34

GB

TECHNICAL DATASeat: PA6 - recyclableFoam: FlameproofCover: GemmaFrame: Powderpainted aluminium

PRODUCERR82 A/SParallelvej 38751 Gedved Denmark

GBGB

DISTRIBUTORGB

Please find your distributor on www.R82.com

35

GB

MAINTENANCEThe x:panda cushion is removable and the cover can be washed at max. 40°. The condition of the foam cushion should be checked at least every six months and replaced if necessary. It is important to keep the frame clean to maintain the validity of the chair.

The carer should check and oil the swing away parts occationally - at least every 6 months.

Use a dry cloth, on a weekly basis, to wipe off filth and dirt from the wheels. Do not use any cleaning materials containing chlorine or methylated spirit.

The x:panda has to be checked and tightened by a qualified technician at least every 6 months to avoid failures.

Do not expose the gasspring to pressure, high temperatures or perforation.

Any adjustments and addition of accessories which are not described in this manual, must only be made by authorized R82 personnel. Vests and belts must be mounted according to the instruction provided with the products.

The carer should check and refill the tyres for air at least once a month. Air pressure:High-low:x outdoor frame. Front: 35 PSI/250 kPa, rear: 40 PSI/2,5 barWheelchair frame. Wheels: 110 PSI/250 kPaPushchair frame. Front: 36 PSI/2,5 bar, rear: 36 PSI/2,5 bar

GB

36

x:panda tm - r82, inc. · 2016-11-16 · g b safety the x:panda has earned the ce-mark. this...

Documents