xcal user guide v3.2
TRANSCRIPT
XCAL-W
User Guide
Version: 3.2.x.x
Updated: 2009.01
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page II
Ⓒ 2009 Accuver EMEA Ltd., All rights reserved.
This documentation shall not be changed, distributed to the public, and opened to
the third person without written permission. Accuver EMEA is not responsible for any
direct or indirect damages arisen or related to use of this manual. All information
included herein may be changed without prior notice.
Accuver EMEA Ltd.,
Address: Suite Two, 1st Floor, Congress House, 14 Lyon Road,
Harrow, Middlesex, HA1 2EN, UK
Web site: www.Accuver.com
Support email : [email protected]
Phone #: +44 (0) 208 863 1118
Fax #: +44 (0) 208 863 1688
I
Contents
Contents ............................................................................................................................ I
Introduction ..................................................................................................................... 1
Overview ................................................................................................... 1
Features .................................................................................................... 3
System Requirements .................................................................................. 4
Installation ....................................................................................................................... 5
Software .................................................................................................... 5
Hardware ................................................................................................... 6
Key Lock Driver ..................................................................................... 6
USB GPS Driver ..................................................................................... 7
Modem Driver ....................................................................................... 8
Window XP SP2 Setting ........................................................................ 10
User Account Control (For Vista User) ..................................................... 14
User Interface ................................................................................................................ 16
Menu Bar ................................................................................................. 17
File .................................................................................................... 17
Logging On/Off .............................................................................. 17
AutoCall Start/Pause/Stop ............................................................... 17
AutoCall Control ............................................................................. 17
User Event .................................................................................... 18
Manual Capture ............................................................................. 18
Replay .......................................................................................... 18
Real Time Mapping ......................................................................... 19
Capture Active Window ................................................................... 19
Capture Main Window ..................................................................... 19
Export Log File .............................................................................. 20
Exit .............................................................................................. 20
Setting .............................................................................................. 21
Port Setting ................................................................................... 21
Mobile Alias Setting ........................................................................ 21
AT Command/Response .................................................................. 21
Color Setting ................................................................................. 22
Cellsite Color Setting ...................................................................... 23
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page II
Key Setting ................................................................................... 24
Alarm Setting ................................................................................ 25
User Event Setting ......................................................................... 32
Log File Setting .............................................................................. 33
BTS Manager ................................................................................. 35
Save All Settings ............................................................................ 37
Load All Settings ............................................................................ 37
Window .............................................................................................. 38
Help .................................................................................................. 39
About ........................................................................................... 39
Icon Bar .................................................................................................. 40
Status Bar ............................................................................................... 41
Worksheet ............................................................................................... 42
Port Setting .................................................................................................................... 43
Start Port Setting ...................................................................................... 43
Port Setting .............................................................................................. 44
Mobile Setting ..................................................................................... 44
GPS Setting ........................................................................................ 45
Enable DHCP ...................................................................................... 45
Set PortWizard .................................................................................... 45
Network RegEdit .................................................................................. 46
Mobile Alias Setting ................................................................................... 47
Interface ............................................................................................ 47
Phone ................................................................................................ 48
Video Phone Option ............................................................................. 49
Data Service Type................................................................................ 49
Data Port ........................................................................................... 50
DUN .................................................................................................. 50
LogMask ............................................................................................ 51
AutoCall Setting ............................................................................................................. 52
AutoCall Scenario Setting ........................................................................... 54
AutoCall Setup ......................................................................................... 57
Scenario Name .................................................................................... 58
Auto Call ............................................................................................ 58
Ignore a Sync Message in Drop (EVDO) .................................................. 60
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page III
Multi RAB (CS+PS) .............................................................................. 60
Dormant Mode .................................................................................... 63
AutoCall Type ...................................................................................... 64
Voice ............................................................................................ 65
FTP .............................................................................................. 68
PPP .............................................................................................. 71
Ping ............................................................................................. 72
HTTP ............................................................................................ 74
Report ............................................................................................... 76
Real Time Mapping......................................................................................................... 79
Map Control Icon ...................................................................................... 82
Map Layer Property ................................................................................... 84
Map (SmartMap) ................................................................................. 84
Map (MIF) .......................................................................................... 86
MAP (MapX) ........................................................................................ 89
BTS ................................................................................................... 91
Repeater ............................................................................................ 92
Serving Line ....................................................................................... 93
Custom Draw ...................................................................................... 94
ETC ................................................................................................... 95
Coverage ........................................................................................... 96
Legend .............................................................................................. 97
Trace ....................................................................................................... 99
Real Time Mapping mouse menu ............................................................... 101
Add Symbol/Polyline/Circle/Polygon ..................................................... 102
Mark List .......................................................................................... 104
Alias Setting ..................................................................................... 105
Message ....................................................................................................................... 107
Signaling Message .................................................................................. 107
Mobile Message ...................................................................................... 109
Alarm Event Manager .............................................................................. 110
Packet Message ...................................................................................... 111
Packet Capture Viewer ............................................................................. 113
PPP Frame Message ................................................................................. 114
Statistics/Status .......................................................................................................... 115
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page IV
Call Statistics (Current Scenario) ............................................................... 115
All Info............................................................................................. 116
Voice .......................................................................................... 116
Data (FTP, PPP, Ping, HTTP) ........................................................... 118
Detailed Info ..................................................................................... 121
Call Statistics View ....................................................................... 121
Call Result View ........................................................................... 124
Call Event History View ................................................................. 127
Call Statistics (All Scenario) ...................................................................... 128
EVDO Session Assignment Test ................................................................. 129
Ping Status ............................................................................................ 130
TraceRT Status ....................................................................................... 131
Throughput Info ..................................................................................... 132
GPS Status ............................................................................................ 133
GPS Satellite Status ................................................................................ 134
Logging Info ........................................................................................... 135
Communication Statistics ......................................................................... 136
QPCH Statistics ....................................................................................... 137
User Define................................................................................................................... 140
Graph ................................................................................................... 140
Table ..................................................................................................... 142
Summary Info ........................................................................................ 143
Cell Measurement ................................................................................... 144
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 1
Introduction
Overview
XCAL is real-time software-based solution for wireless network optimization and
performance measurement. XCAL collects Layer 1, 2, and 3 messages, and TCP/IP
packets from both the air and data interface of all commercially available
technologies (CDMA IS95A/B, 1XRTT, EVDO (Rev. 0 and Rev. A), GSM, GPRS, EDGE,
UMTS, HSDPA, and HSUPA). XCAL is also proven to significantly reduce overhead
and improve operational efficiency.
XCAL allows several mobiles to interface simultaneously with different technologies
and provides an ideal solution for measuring both voice and data service
performance. XCAL can be used for both indoor and outdoor measurement.
XCAL System Overview
XCAL User Guide Chapter 1. Introduction
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 2
XCAL Program
XCAL User Guide Chapter 1. Introduction
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 3
Features
The key features of XCAL are as follows:
Simultaneous data collection of both Layer 1/2/3 messages and TCP/IP
packets of different technologies
Supports CDMA IS95-A/B, 1XRTT, EVDO (Rev. 0 and Rev. A), GSM, GPRS,
EDGE, UMTS, HSDPA, and HSUPA
Supports QUALCOMM chipset (CDMA/WCDMA) and Nokia chipset
(WCDMA/EDGE)
Supports various scanners
Automatic call generation and termination
Log and decode messages in real-time
Comprehensive graphic analysis of signal and throughput
Handoff analysis/real time mapping
Voice alarm for important events
Log file replay
XCAL User Guide Chapter 1. Introduction
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 4
System Requirements
Before you begin, ensure that your system meets the following requirements.
Item Requirements
PC Pentium M processor 1.7GHz or above
* For Vista, above core2 duo
Monitor VGA (Over 1024 * 768, 256 color)
RAM 1GB or above
*For Vista, above 2GB
Hard Drive 40GB or above
Operation System - Windows2000/XP/Vista
Map - Supported Format: Map Info
- Scan Map : Bmp Supporting
© Copyright by Innowireless Co., Ltd. Page 5
Installation
Software
The following procedures enable you to install XCAL on the computer appropriately.
All applications should be closed on your PC before beginning installation.
1. Insert the supplied CD-ROM into your CD-ROM drive.
The CD-ROM shall automatically run, and an installation window appears.
If the installation window does not appear, find the setup.exe from the
supplied CD-ROM/XCAL Setup.
2. Installation wizard is started, read carefully and follow installation
instructions properly.
3. Click Finish.
XCAL User Guide Chapter 2. Installation
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 6
Hardware
Key Lock Driver
Key lock driver is a security program for XCAL; it enables you to operate
XCAL.
1. Connect a Dongle key to USB port of your PC.
2. Execute autorun.exe (or autorun.bat) from CD-ROM/Driver/Key Lock
Driver.
3. Installation wizard is started, read carefully and follow installation
instructions properly.
4. Click Finish.
XCAL User Guide Chapter 2. Installation
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 7
USB GPS Driver
Following procedure enables you to install USB GPS driver on the computer
appropriately. All applications should be closed on your PC before beginning
installation.
1. Insert the supplied CD-ROM into your CD-ROM drive.
The CD-ROM shall automatically run, and an installation window appears.
If the installation window does not appear, find the USB GPS Driver.exe
from the supplied CD-ROM.
2. Installation wizard is started, read carefully and follow installation
instructions properly.
3. Click Finish.
XCAL User Guide Chapter 2. Installation
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 8
Modem Driver
The following procedures allow you to connect modem driver which connects
test mobile and PC.
1. Connect test mobile and PC with USB cable.
2. Found New Hardware Wizard window appears automatically.
3. Click Next.
4. Install Hardware Device Drivers dialog box appears. Select the
location where the modem driver is installed and click the Next button.
XCAL User Guide Chapter 2. Installation
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 9
5. Click Next.
6. Modem driver installation is completed. Click Finish.
You may find the installed modem driver from Control Panel – System –
System Properties – Device Manager.
XCAL User Guide Chapter 2. Installation
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 10
Window XP SP2 Setting
The following procedure introduces you how to set for Windows XP SP2.
1. Update your OS from Start - Windows Update.
2. Go to Start – Control Panel – Security – Windows Firewall.
XCAL User Guide Chapter 2. Installation
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 11
3. Windows Firewall Settings window appears. Select Off (not
recommended).
4. Go to Start - Control Panel – Windows Update – Change Setting.
Select Never check for updates (not recommended).
XCAL User Guide Chapter 2. Installation
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 12
5. Go to Start – Control Panel – Date and Time – Internet Time tab.
Click Change Setting button.
XCAL User Guide Chapter 2. Installation
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 13
6. Change Setting window appears. Unselect Synchronize with an
Internet time server.
XCAL User Guide Chapter 2. Installation
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 14
User Account Control (For Vista User)
1. Click Start – Control Panel.
2. Click on User Accounts.
XCAL User Guide Chapter 2. Installation
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 15
3. Click on Turn User Account Control on or off.
4. Uncheck the box for Use User Account Control (UAC) to help protect
your computer.
5. Reboot the PC.
© Copyright by Innowireless Co., Ltd. Page 16
User Interface
This chapter introduces you how to use basic user interface of XCAL.
Main window of XCAL is composed of four sections; Menu Bar, Icon Bar, Status Bar,
Worksheet.
XCAL main window
Classification Description
Menu Bar Include File, Setting, Window, and Help.
Menu items vary depending on supported technologies.
Icon Bar Provide easy access on basic functions.
Workspace Display various parameter windows.
Status Bar Show Slot, Phone, GPS status.
Worksheet Save currently opened windows and their settings in a worksheet.
You may create max 30 worksheets.
XCAL User Guide Chapter 3. User Interface
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 17
Menu Bar
Menu Bar includes basically four pull-down menus; File, Setting, Window, and Help.
Features menu varies depending on supported technologies. Refer to provided Features
User Guide for each technology.
Menu Bar
File
File menu includes basic functions such as Replay and Real Time Mapping.
File:> Logging On/Off
Save messages from test mobile.
You may save messages from test mobile by using Logging icon from
Icon Bar.
NOTE: If you select on Logging icon while AutoCall is in progress, message
logging is started right after you select on the Logging icon.
File:> AutoCall Start/Pause/Stop
Start, pause, and stop voice and data call (FTP, PPP, Ping).
AutoCall Start enables you to start AutoCall by creating AutoCall Scenario.
For detail, refer to AutoCall Setting – AutoCall Scenario Setting.
File:> AutoCall Control
Process AutoCall test per mobile.
XCAL User Guide Chapter 3. User Interface
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 18
Autocall Control Info window
File:> User Event
Set shortcuts for any events you want to mark.
1. Set event name you want to set shortcut key.
For detail, Menu Bar – Setting – User Event Setting.
2. Set shortcut key for each event name.
For detail, Menu Bar – Setting – Key Setting.
3. Press the shortcut key on your keyboard while AutoCall is in progress.
The events are marked at the selected point, and can be found from
XCAP analyzer.
File:> Manual Capture
Capture packets when you make calls through call connecting adapter.
File:> Replay
Replay existing measured data during drive test in field.
1. Select Menu Bar – File – Replay, or click on Replay icon from
Icon Bar.
2. Open window appears. Select a logging file you want to replay and click
Open button.
3. Replay Control bar appears.
XCAL User Guide Chapter 3. User Interface
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 19
The detailed description of each icon on Replay Control Bar is as follows.
Icon Description
Open Open existing logging file.
Play Start or resume replay.
Rev. Reverse replay.
Pause Pause replay.
Stop Stop replay.
Chip type Select chipset type.
Speed Control replay speed.
Current Time Show replay process time.
Time bar Show replay status.
4. Click on Play button to start replay.
NOTE: Once you replay a logging file, the file is converted in .rpl and saved
in Replay folder. You may use replay settings if you replay with the logging
file saved in .rpl.
File:> Real Time Mapping
Display major RF parameters and call result (drop, setup fail, etc.) on Real
Time Mapping window graphically. It displays call event and serving lines
between active base stations and current position of a test mobile.
For detail, refer to Real Time Mapping.
File:> Capture Active Window
Save a selected window in bmp.
File:> Capture Main Window
Save all opened windows in bmp.
XCAL User Guide Chapter 3. User Interface
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 20
File:> Export Log File
Export selected parameters in xls, csv, txt.
1. Select Menu Bar – File – Export Log File.
2. Export Log File window appears.
Export Log File window
3. Select parameters you want to export.
File Type: Select export file type (xls, csv, txt).
Include GPS Info: Include GPS information in export file.
4. Click Close.
File:> Exit
Close all windows and terminate the program.
XCAL User Guide Chapter 3. User Interface
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 21
Setting
Setting menu includes basic settings such as Port Setting, Mobile Alias Setting,
and etc.
Setting menu
Setting:> Port Setting
Set serial communication between XCAL and test mobiles.
You may perform Port Setting by using Port icon from Icon Bar.
For detail, refer to Port Setting.
Setting:> Mobile Alias Setting
Set mobile chipset type, phone model, logmask, data port, and etc. for test
mobiles.
For detail, refer to Port Setting - Mobile Alias Setting.
Setting:> AT Command/Response
Transfer User AT Command to test mobile and display received response
from test mobile.
1. Select Menu Bar – Setting – AT Command/Response.
XCAL User Guide Chapter 3. User Interface
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 22
2. AT Command window appears.
3. Enter value in User AT Command entry field.
4. Click OK.
5. Response from test mobile is displayed in the status section on the
bottom of AT Command window.
AT Command window
Setting:> Color Setting
Set colors for Table, Graph, Message, etc. windows.
1. Select Menu Bar – Setting – Color Setting.
2. Color Setting window appears.
XCAL User Guide Chapter 3. User Interface
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 23
Color Setting window
3. Double click on color cell and change color.
4. Click OK.
Setting:> Cellsite Color Setting
Set color for Cellsite.
1. Select Menu Bar – Setting – Cellsite Color Setting.
2. Cellsite Color Setting window appears.
XCAL User Guide Chapter 3. User Interface
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 24
Cellsite Color Setting window
3. Double click on cellsite number you want to change color, and change
color.
4. Click OK.
Setting:> Key Setting
Set shortcut key for each menu item such as File, Setting, and etc.
1. Select Menu Bar – Setting – Key Setting.
2. Key Setting window appears.
Key Setting window
3. Select menu item you want to set shortcut key from Types section.
4. Select detailed menu item from Commands section.
5. Enter shortcut key (e.g. Ctrl, Alt, Shift + Alphabet, or F1 ~ F9) in Press
new shortcut entry field.
6. Click Assign button to apply the shortcut.
7. Assigned shortcut section shows designated shortcut.
8. Click OK.
XCAL User Guide Chapter 3. User Interface
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 25
Setting:> Alarm Setting
Notify important events occurred during test by sound and a pop-up alarm
window.
1. Select Manu Bar – Setting – Alarm Setting.
2. Alarm Setting window appears.
Alarm Setting window
3. Select checkboxes you want to set for Alarm.
4. Click OK.
For detail for each tab settings, refer to below sections; Event,
Signaling, RF Parameter, System Transition.
5. Click on Alarm icon from Icon Bar.
6. Alarm window appears when the predefined events are occurred.
Alarm window
XCAL User Guide Chapter 3. User Interface
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 26
NOTE: You may find alarm list from Menu Bar – Message – Alarm Event
Manager. For detail, refer to Message – Alarm Event Manager.
Alarm Event Manager
Event tab
Explain how to set Event tab in Alarm Setting window.
Alarm Setting_Event tab
XCAL User Guide Chapter 3. User Interface
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 27
You may set alarms for the following events.
Classification Description
Call event Drop, Setup Fail, etc
Mobile Mobile Alarm
Scanner Scanner Alarm
GPS GPS Alarm
Handoff CDMA/EVDO: PN change
WCDMA: PSC change
GSM/GPRS/EDGE: ARFCN change
Network SID change, NID change, Color code change, Sector ID
change
Data performance WCDMA: SF change
GPRS, EDGE: DL/UL slot number change
GPRS, EGDE: Coding scheme change
1. Select event checkboxes you want to be notified.
2. Click OK.
NOTE: You may change alarm sound by double-clicking on a File Path cell.
XCAL User Guide Chapter 3. User Interface
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 28
Signaling
Explain how to set Signaling tab in Alarm Setting window.
Alarm Setting_Signaling tab
You may set alarms for messages.
1. Select signaling message you want to be notified, and drag it into
Monitoring Message List section or double click it.
If there are more than one messages you want to be notified, repeat
step 1.
2. Enter message holding time (sec) in Duration entry field.
An alarm window pops up when the message in the list is received
within the duration time defined.
3. Clear icon removes all Monitoring Message List, and
Delete icon removes the selected message in Monitoring Message
List.
4. Click icon to change alarm sound.
5. Enter alias name in Alias Name entry field.
XCAL User Guide Chapter 3. User Interface
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 29
6. Click on Add/Edit button to add a new alias.
You may create several Alias by repeating step 1 through 6.
NOTE: Only one Alias can be applied to a mobile type.
7. Click OK.
RF Parameter
Explain how to set RF Parameter tab in Alarm Setting window.
Alarm Setting_RF Parameter tab
You may set alarms for major RF parameters.
XCAL notifies RF parameters which meet the conditions set at RF
Parameter tab. You can be notified major RF parameters such as Pilot
Pollution, Coverage Problem, and Low Throughput, etc.
1. Select RF parameters you want to be notified, and drag it into Name
List section or double click it.
If there are more than one RF parameters you want to be notified,
repeate step 1.
XCAL User Guide Chapter 3. User Interface
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 30
2. Set parameter condition.
Set Link condition if you selected more than one RF parameters in
Name List.
3. Enter time (sec) in Duration entry field.
An alarm window pops up when the RF parameter in the list meets the
condition during the duration time defined.
If you entered 0 sec, an alarm window pops up as soon as the RF
parameter which meets the defined condifion is occurred.
4. Clear icon removes all Name List, and Delete icon removes
the selected message in Name List.
5. Click icon to change alarm sound.
6. Enter alias name in Alias Name entry field.
7. Click on Add/Edit button to add a new alias.
You may create several Alias by repeating step 1 through 7.
NOTE: Only one Alias can be applied to a mobile type.
8. Click OK.
System Transition
Explain how to set System Transition tab in Alarm Setting window.
XCAL User Guide Chapter 3. User Interface
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 31
Alarm Setting_System Transition tab
You may set alarms for system transition.
1. Set Band Class, Channel, and System.
2. An alarm window pops up when an event meets the conditions.
3. Click OK.
XCAL User Guide Chapter 3. User Interface
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 32
Setting:> User Event Setting
Name special events.
Event Setting window
1. Enter favorable event name in Event# entry field.
2. Click OK.
NOTE: Set user event names, set their shortcut from Manu Bar – Setting
– Key Setting, and use the shortcuts from Analyzer.
XCAL User Guide Chapter 3. User Interface
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 33
Setting:> Log File Setting
Set save path of logging file.
Log File Setting window
The detailed description of each item in Log File Setting window is as
follows.
Classification Description
Log File Path Save log file at default path: Save logging file in default
path.
Save log file at the user defined path: Save logging file
in the folder you designated. You may change the save
path by clicking icon.
Add then default path (Year/Month/Day) at the user
defined path: Include date (Year/Month/Day) in logging
file name.
Support Qualcomm
Format (*.mdm)
Save logging file in *.mdm.
XCAL User Guide Chapter 3. User Interface
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 34
Log File Name User Prefix: Add file name as a prefix.
Additional Name
Interface Name: Add interface name at the back of
logging file.
AutoCall Scenario Name: Add AutoCall Scenario name at
the back of logging file.
Manual Logging Keep Logging: Keep manual logging in progress when
you start AutoCall.
Upload logfile after
autocall
Upload logging file onto FTP server as soon as logging
terminated.
XCAL User Guide Chapter 3. User Interface
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 35
Setting:> BTS Manager
Display BTS information and serving lines at TA Graph, Real Time Mapping,
and etc.
It helps you to figure out currently communicated BTS graphically.
BTS Manager window
1. Select BTS or Repeater from Mode.
2. Select technology. (Technology list may vary depending on product.)
XCAL User Guide Chapter 3. User Interface
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 36
3. Click Import.
4. BTS Import Manager window appears.
5. Click Open File button to import BTS file.
6. Select on the checkbox for Exclude first line if you want to enter data
from the first line.
Select on the checkbox for All sectors per line if there are more than
one sector information on one column.
7. Define each item name in accordance with imported file. Select each
item and appropriate type.
XCAL User Guide Chapter 3. User Interface
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 37
8. Click New button to add a new data.
Click Append button to update an existing data.
9. Import data setting is completed.
10. Click Export button to save data in xls, csv, txt.
11. Click OK.
Setting:> Save All Settings
Save the setting in *.ini.
Setting:> Load All Settings
Import saved setting in *.ini.
XCAL User Guide Chapter 3. User Interface
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 38
Window
Display opened parameter windows in different types.
Classification Description
Cascade (F10) Arrange parameter windows in workspace tiered.
Title Horizontally
(F11) Arrange parameter windows in workspace horizontally.
Title Vertically
(F12) Arrange parameter windows in workspace vertically.
Close Close the current window.
All Close (Current
Worksheet)
Clear the current worksheet.
All Close (All
Worksheet)
Clear all worksheets opened.
XCAL User Guide Chapter 3. User Interface
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 39
Help
About
Provdie XCAL version information.
XCAL User Guide Chapter 3. User Interface
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 40
Icon Bar
Allow you to access basic functions easily and quickly.
Icon Description
Set serial port between test mobile and PC.
For detail, refer to Port Setting.
Save measurement data.
For detail, refer to User Interface – Menu Bar – File – Logging On/Off.
Replay logging data.
For detail, refer to User Interface – Menu Bar – File – Replay.
Option for User Defined feature.
Trace data in past time. The orange icons on Trace bar moves 10 seconds
back and forth between data, and the pink icons moves 1 second back and
forth.
Notify special events.
For detail, refer to User Interface – Menu Bar – Setting – Alarm Setting.
Start AutoCall.
For detail, refer to AutoCall Setting.
Stop AutoCall.
Display major RF parameters and Call result on Real Time Mapping.
For detail, refer to Real Time Mapping.
XCAL User Guide Chapter 3. User Interface
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 41
Status Bar
Classification Description
Slot Status
Slot is not booted.
Slot is booted.
Phone Status
Slot in Port Setting window is not set. XCAL recognize there is no test
mobile connected.
Communication between XCAL and test mobile is failed as follows.
• No physical connection between mobile and PC
• Wrong phone (chip) type in Port Setting window
• Wrong port number in Port Setting window
• Wrong log mask setting in Port Setting window
Port between XCAL and test mobile is set successfully.
Test mobile number or Mobile# appears when successfully connected.
GPS Status
No GPS GPS in Port Setting window is not set. XCAL recognize there is no GPS
connected.
[,] GPS connection attempts.
[E0.0000,N0.000
0,m]
No exact GPS location information is received from satellite.
GPS Alarm GPS connection attempt is failed.
[E127.3XX,N33.7
XXX,83m]
GPS connection attempt succeed.
To make sure usability of GPS location information, refer to
Statistics/Status – GPS Status.
XCAL User Guide Chapter 3. User Interface
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 42
Worksheet
Save all opened windows and its settings in a worksheet.
Default worksheet is named Worksheet, and cannot be changed.
You may create, rename, remove, load, save worksheets by right-clicking on a
worksheet.
NOTE: You may create maximum 30 worksheets.
Classification Description
New Worksheet Create a new worksheet.
Rename Worksheet Rename the current worksheet.
Remove Worksheet Remove the current worksheet.
Load my Worksheet Load existing worksheet.
Save my Worksheet Save the current worksheet.
Copyright by Innowireless Co., Ltd. Page 43
Port Setting
This chapter explains how to set test mobile, GPS, serial communication between
XCAL and test mobile.
A slot supports one test mobile. You may test with several test mobiles by activating
each slot in Port Setting window.
NOTE: Before you begine port setting, make sure SIO mode. Port set from test
mobile and data setting should correspond.
SIO mode in test mobile may vary, make sure ISO mode depending on test mobile
teyp.
Start Port Setting
1. Select Manu Bar - Setting – Port Setting, or click on Port icon from Icon
Bar.
2. Port Setting window appears.
Port Setting window
XCAL User Guide Chapter 4. Port Setting
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 44
Port Setting
The detailed explanaion of each item in Port Setting widnow is as follows.
Port Setting window
Mobile Setting
Connect XCAL and test mobile.
Set Phone type, data port, logmask, DUN. For detail, refer to Port Setting –
Mobile Alias Setting.
1. Click on icon from mobile setting.
2. Mobile Alias Setting window appears.
XCAL User Guide Chapter 4. Port Setting
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 45
Mobile Alias Setting window
GPS Setting
Set GPS configuration.
Check GPS Slot and set GSP set values.
The detailed description of each item for GPS Setting is as follows.
Classification Description
Com Port Set Com Port which receives location information from GPS.
Make sure your Com Port information from Device Manager.
GPS Type Set GPS type.
GPS type supported: NMEA, Trimble, Pioneer, Accuver, TAIP(LN)
Baud Rate Set communication speed with GPS.
Flow Control Set flow control type.
GPS Time Sync Synchronize time using GPS.
Time Revision
(sec)
Supplement time.
Default value: Leap second
Enable DHCP
Uncheck if you test multiple data at once.
Set PortWizard
If you are a Portwizard tool user, this button activated.
Portwizard tool helps you to set DM Port, Modem Port automatically.
XCAL User Guide Chapter 4. Port Setting
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 46
Network RegEdit
Set network configuration for data communication.
Network RegEdit window
The detailed description of each item in Network RegEdit window is as follows.
Classification Description
MTU Maximum packet size to be transmitted in IP layer
Window TCP Window Size
Throughput of applications which use TCP depends on it.
8760 : setting of low speed test
65535 : setting of high speed test
TTL Time-To-Live
Time-To-Live judges the retransmission of packet and indicates
scope and node to get the destination
- 1: limit to the same subnet
- 32: limit to the same site
- 128: limit to the same continent
- 255: no limit
Sack Selective ACK.
Default is set to ‘1’
Ack Acknowledgement delay.
Default is set to ‘2’
XCAL User Guide Chapter 4. Port Setting
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 47
Mobile Alias Setting
Connect XCAL and test mobile.
1. Click on icon at Mobile from Port Setting window.
2. Mobile Alias Setting window appears.
Mobile Alias Setting window
Interface
Enter interface name in Interface entry field.
1. Set mobile alias setting.
2. Enter interface name in Interface entry field.
3. Click on Add/Edit button to add Alias List.
Click on Del button to remove the selected alias list.
XCAL User Guide Chapter 4. Port Setting
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 48
Phone
Set test mobile to be connected.
The detailed description of each item for Phone setting is as follows.
Classification Description
Chip Type Define the modem chipset of the mobile.
Phone Model Select the mobile model.
Baud Rate Designate the communication speed through DM port.
Flow Control Designate the method of flow control.
Don’t Use Key
Emulation (For
Special Card
Phone)
For specific card phone, key emulation function is note applied.
Streaming
Logging
Determine if streaming logging is executed.
- Checked (default): XCAL sends Packet Request Logmask to
mobile and the mobile will send data continuously without any
other requests.
- Unchecked: XCAL sends Packet Request Logmask to mobile
periodically and the mobile will sends data packets as per the
requests.
If streaming logging is checked for non streaming mobile, data is
displayed once and then blank state will follow.
Safe Mode In case specific old non streaming mobile, message loss is
happened a lot.
If user checks this item, message loss should be reduced.
Extended Mobile
Message
Additional mobile message
User select extended mobile message which user want to see
additionally.
XCAL User Guide Chapter 4. Port Setting
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 49
Video Phone Option
Set if you use video mobile as a test mobile.
The detailed description of each item for Vide Phone Option is as follows.
Classification Description
Send Key Press Enter send key value of test video mobile.
If your send key value is 0x10, enter 10.
If you need to enter more than one send key values, use semi
colon between key values (e.g. 10;20;30).
Receive Key
Press
Enter receive key value of test video mobile.
Delay for
Receive Key
(ms)
Enter receive key delay value of test video mobile.
Data Service Type
Set for data call test.
The detailed description of each item for Data Service Type is as follows.
Classification Description
Moderm Select for test mobile with modem.
Network
Adapter
Select for test mobile with Network Adpater and Connection
Manager program.
XCAL User Guide Chapter 4. Port Setting
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 50
Data Port
Set data port for data measurement.
The detailed description of each item for Data Port is as follows.
Classification Description
Dial Num Dial number to connect to packet data switch.
User ID User ID to connect to packet data switch.
Password Password to connect to packet data switch
Extra Setting at+crm value used by packet data switch.
*CDMA/EVDO: at+crm=1, at+crm=150, at+crm=160 ……
*WCDMA :
Example:
AT+CGDCONT=1,IP+CGEQREQ=1,3,128,384
Note: Refer to standards document “Commands for Packet Domain
of 3GPP TS 27.007 (AT command set for User Equipment (UE))”
DUN
Set DUN setting.
The detailed description of each item for DUN setting is as follows.
Classification Description
IP Header Comp Use IP Header compression.
LCP Ext Use LCP expansion.
Nego. Multi-link Negotiate multi link during initial LCP
S/W Comp Use software compression.
Mdm H/W Flow Use hardware control.
XCAL User Guide Chapter 4. Port Setting
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 51
LogMask
Select message type between XCAL and test mobile.
XCAL displays the items selected from LogMask only.
LogMask items may vary depending on product.
1. Select LogMask item you want to display on XCAL.
2. Enter LogMask name in LogMask Alias entry field.
3. Click on Add/Edit button to add to Alias List.
Click on Del button to remove the selected Alias List.
Copyright by Innowireless Co., Ltd. Page 52
AutoCall Setting
This chapter enables you to create Scenarios for Voice and Data (FTP, PPP, Ping) Call
and process AutoCall Test using the created Sceanrio.
1. Select Manu Bar - File – AutoCall Start, or click on AutoCall icon from
Icon Bar.
2. AutoCall Scenario Setting window appears.
AutoCall Scenario Setting window
3. Create a Scenario.
For detail, refer to AutoCall Setting – AutoCall Scenario Setting.
4. Click Create New Scenario icon to create a new scenario in AutoCall
Setup window.
XCAL User Guide Chapter 5. AutoCall Setting
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 53
For detail, refer to AutoCall Setting -AutoCall Setup.
5. Drag a sceario from Scenario Name list on the left section into AutoCall
Scenario on the right section.
Double click to cancel the selected scenario.
6. Scenario is registered from mobile #1.
7. Click OK.
8. AutoCall is started.
9. If you selected AutoCall Logging Option, Save logging file window appears.
For detail, refer to AutoCall Setting - AutoCall Scenario Setting.
Save logging file window
10. Enter a file name to be saved and set save path. Click Save.
11. Call Statistics (Current Scenario) window appears.
For detail, refer to Statistics/Status – Call Statistics (Current Scenario).
XCAL User Guide Chapter 5. AutoCall Setting
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 54
AutoCall Scenario Setting
AutoCall Scenario Setting window allows you to create Scanario for AutoCall test.
Create different scenarios for each call type.
The detailed description of each item in AutoCall Scenario Setting window is as
follows.
Classification Description
Create New Scenario
Create a new scenario.
Click on this icon, and AutoCall Setup window appears.
For detail, refer to AutoCall Setting - AutoCall Setup.
Edit Scenario
Edit existing scenario.
Select a scenario you want to edit from Scenario Name
box, and click on Edit Scenario icon.
Delete Scenario
Delete a scenario.
Select a scenario you want to delete from Scenario Name
box, and click on Delete Scenario icon.
Import Scenario
Import an existing scenario.
Export Scenario
Save a created scenario.
AutoCall Logging Option Set logging option.
Per # Call: Generate logging file call by call.
Each Scenario: Generate logging file scenario by scenario.
All Scenarios: Generate one logging file for all scenarios.
Per File Size(MB): Generate logging file in accordance with
logging data size defined.
Per Time (h,m): Generate logging file adding logging time
defined.
By Call End: log adding time to AutoCall termination
time.
By Accurate Point: log adding defined time and
terminate.
XCAL User Guide Chapter 5. AutoCall Setting
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 55
Classification Description
Non: Generate no logging file.
Extend logging time (sec): If you selected on Per Call or
Each Scenario for Logging Option, extend time from
release end to call end of the last call.
Stop logging when autocall finished: Terminate logging
as soon as AutoCall is stopped. If item is unselected, logging
is not stopped after AutoCall is terminated.
AutoCall Export Option All Info of Call Statistics (JPG): Save All Info window in
jpg when AutoCall is terminated.
For detailed information of All Info window, refer to
Statistics/Status – Call Statistics (Current Scenario) -
All Info.
Detail Info of Call Statistics (TXT): Save Detailed Info
window in txt when AutoCall is terminated.
For detailed information of Detailed Info window, refer to
Statistics/Status –Call Statistics (Current Scenario) -
Detail Info.
AutoCall Reservation
Option
Reserve AutoCall scenario.
Start Time: Enter start time for AutoCall Reservation
process.
End Time: Enter end time for AutoCall Reservation process.
Port Set AutoCall start time if you connect more than one test
mobiles for test.
Sync: Start AutoCall for all test mobiles and restart the next
attempt after all calls are terminated.
Async: Start AutoCall for each mobile respectively.
Cycle: Start AutoCall in order of test mobile number.
NOTE: If you test with more than one mobiles and set Sync
for Port and set Disable for AutoCall Scenario Sync, the
disabled mobile is to be excluded for test.
Apply Row
Move up the selected scenario.
XCAL User Guide Chapter 5. AutoCall Setting
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 56
Classification Description
Apply All
Move down the selected scenario.
Delete All
Delete all created scenarios.
AutoCall Scenario Set how to process AutoCall scenario.
Repeat: Set number of repeat for the scenario.
Sync: Able/Disable Port – Sync option.
Keep Con.: Once PPP is connected at the first call, it is not
unconnected and continued. PPP is not connected from the
next call.
Group: Process AutoCall scenario in group if you set Port –
Cycle.
AutoCall Scenario Time
Show time information of the selected AutoCall scenario.
XCAL User Guide Chapter 5. AutoCall Setting
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 57
AutoCall Setup
AutoCall Setup window allows you to create a new scenario.
Click on Create New Scenario icon in AutoCall Scenario Setting window.
AutoCall Setup window
NOTE: AutoCall Setup window may be shown differently depending on mobile chip
types.
The detailed description of each item in AutoCall Setup window is as follows.
XCAL User Guide Chapter 5. AutoCall Setting
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 58
Scenario Name
Enter a scenario name to be created in Scenario Name entry field.
Scenario Name Setting
Auto Call
Set time configuration for each AutoCall scenario.
Auto Call Setting
The detailed description of each item for AutoCall time setting is as follows.
Classification Description
Idle Time Time period between calls.
Setup Time Maximum period to setup radio link connection for Voice/CS
or to establish PPP connection for a call.
T_Setup Time Maximum time period to connect to application server after
establishment of PPP connection. This field is valid for packet
data service application.
Total Setup Setup time plus T_Setup time
* Applies for only FTP & HTTP Call.
Traffic Time Maximum time period to sustain connection for voice, ping &
traceRT calls.
Time limit for completing activities after application server is
connected for data calls such as FTP, TFTP, HTTP, PPP calls.
Call Count Repeat counts each call that Idle / Setup(T_Setup) / Traffic
Time
XCAL User Guide Chapter 5. AutoCall Setting
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 59
Total Time (sec) Time interval between calls
Enter more than the time of (Idle Time + Setup Time
(+T_Setup Time) + Traffic Time)
[Time Configuration for voice Call]
[Time Configuration for Data Call]
XCAL User Guide Chapter 5. AutoCall Setting
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 60
Ignore a Sync Message in Drop (EVDO)
Ignore drop calls occurred due to sync messages in EVDO.
Ignore a Sync Message in Drop (EVDO) setting
Multi RAB (CS+PS)
Test both Voice and Data call simultaneously.
This function supports mobiles with DO Rev. A and with WCDMA.
The two scenarios for voice and data call are processed starting the first call
starts and the second call starts when the first call’s traffic start is occurred.
Multi RAB (CS+PS) setting
XCAL User Guide Chapter 5. AutoCall Setting
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 61
Multi Rab structure
1. Select first call type from 1st Call Type.
2. Select corresponding tab from AutoCall Type tab on the right section and
set scenario.
For detail, refer to AutoCall Setting – AutoCall Setup -AutoCall Type.
3. Select second call type from 2nd Call Type.
4. Select corresponding tab from AutoCall Type tab on the right section and
set scenario.
5. Check 2nd Call Time Setting, and set time for the second call.
Multi RAB Statistics window
XCAL User Guide Chapter 5. AutoCall Setting
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 62
Multi RAB Event window
NOTE: Events with M at the end is for the second call.
XCAL User Guide Chapter 5. AutoCall Setting
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 63
Dormant Mode
Set dormand mode for test mobile.
Dormant Mode setting
Time: Keep call for the defined time.
Allow Dormant State: Keep call by traffic time termation.
NOTE: This option appears when Data Call (FTP, PPP, Ping, HTTP) tab is
selected from AutoCall Type. For detail, refer to AutoCall Setting –
AutoCall Setup - AutoCall Type.
XCAL User Guide Chapter 5. AutoCall Setting
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 64
AutoCall Type
Set AutoCall scenario depending on call types; Voice and Data call.
You may set for Voice (CDMA, QC-WCDMA), and Data (FTP, PPP, Ping, HTTP)
call types.
AutoCall Type section
XCAL User Guide Chapter 5. AutoCall Setting
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 65
Voice
Set for voice call test.
You may set in CDMA and QC-WCDMA tabs.
Voice Call_CDMA setting Voice Call_QC-WCDMA setting
The detailed description of each item in the tabs is as follows.
Classification Description
Call Type Set AutoCall test type.
Idle: Connect no calls and keep idle condition.
Origination: Test mobile transmit call test.
Termination: Test mobile receive call test. Sufficient Idle
Time should be set due to it page responses in Idle Time.
Continuous Call: The same as Origination, but it maintains
a call continuously regardless of Traffic time on Auto Call
Part.
M to M Org: Calling the other mobile in case 2 mobiles are
connected to XCAL. (Assign the other mobile in the
Destination field).
M to M Ter: Receiving a call from the other mobile in case 2
mobiles are connected to XCAL. (Assign the other mobile in
XCAL User Guide Chapter 5. AutoCall Setting
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 66
Classification Description
the Destination field).
Dialed Digit Designate phone number to be dialed.
Service Option Designate Service Option for voice call.
It is valid on the phones with CDMA Qualcomm chipset.
AMR Rate Designate AMR rate. It is valid on the phones with WCDMA
Qualcomm chipset.
Call Flow Designate the starting point for traffic state.
Traffic state starts when RB Setup, Alert, or Connect
message is detected.
Success Time When Call Type is set to Termination and the call is kept for
Success Time even if the call is not kept for Traffic Time, the
call is determined as Success.
Receive Set receive button.
“Send” button: Click Send button to receive test mobile to
be transmitted.
“0” button: Click 0 button to receive test mobile to be
transmitted.
NOTE: For some WCDMA mobiles, it is impossible to receive
by 0 button.
Alternation Set for alternative transmit/receive.
OT: Repeat one transmit and one receive.
TO: Repeat one receive and one transmit.
End Call Using
“End” Button
Terminate voice call by End Key command defined.
Dial using
keypress
Emulate the dial by pressing keys for call origination to make
a call on a phone.
Video Phone Call Video conference call in Samsung, Qualcomm and Sanyo
WCDMA phone can be generated by using key command.
NOTE: This option supports WCDMA only.
XCAL User Guide Chapter 5. AutoCall Setting
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 67
Voice Call Time
XCAL User Guide Chapter 5. AutoCall Setting
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 68
FTP
Set for FTP call test.
FTP Call setting
The detailed descriptoin of each item for FTP setting is as follows.
Classification Description
Host Designate IP number of host server to connect
Login ID Login ID of host server
Password Password of host server
Change Dir Designate the directory of host server where file to be
downloaded.
XCAL User Guide Chapter 5. AutoCall Setting
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 69
Classification Description
Ger File Designate file name to be downloaded.
Put File Designate file size to be uploaded. Select the file size from
the drop down list. To transfer file size which is not on the
list, type the number.
- Unit: k = KB, m = MB
- No unit = XCAL assumes MB
Logging FTP Raw
Data
Check: logging payload data of TCP
Uncheck: logging only header data
Port Set port number per protocol.
Passive Mode Selects the FTP server is connected with the passive mode
Repeat Designate repeat count. After server connection, it repeats
the Get File or, the Put File command in traffic.
* Count : Set the repeat count
* Delay : Set the delay until the before get file
Release after LCP
Ter nego
If the option is checked, it will wait for PPP Release order
after the completion of Data transmission. If the option is
unchecked, it does not wait for PPP Release order and it ends
call using the End button. User can confirm LCP packet from
packet message window.
Pending If measured throughput meets the condition which user sets,
pending event is occurred. Upon pending, XCAL stops the
current call and start next call.
PPP/Ethernet: Select whether the pending condition will be
applied to PPP/Ethernet layer throughput.
FTP: Select whether the pending condition will be applied to
FTP (application) layer throughput.
Start Time (sec): The duration between the traffic start
time and when pending condition starts to be measured.
Interval (sec): If the throughput value remains under the
defined threshold value for the defined interval period,
pending event is declared and the call is terminated.
Threshold (Kbps): The desired throughput value in kbps
If throughput remains under the defined threshold value for
the defined interval period, pending event is declared and
the call is terminated.
XCAL User Guide Chapter 5. AutoCall Setting
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 70
Classification Description
3GPP QoS and APN Sets QoS and APN of PDP Context which is defined in 3GPP.
Refer to 3GPP TS 27.007 (http://www.3gpp.org/)
FTP Call Time
If throughput is sustained under predefined threshold for designated time
threshold, then pending is declared and the call will be dropped.
Pending event
XCAL User Guide Chapter 5. AutoCall Setting
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 71
PPP
Set for PPP call test.
PPP Call setting
The detailed description of each item for PPP setting is as follows.
Classification Description
3GPP QoS and APN Refer to 3GPP TS 27.007 (http://www.3gpp.org/)
XCAL User Guide Chapter 5. AutoCall Setting
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 72
Ping
Set for Ping call test.
Ping Call setting
The detailed description of each item for Ping call setting is as follows.
Classification Description
Classification Single Ping: Meausre delay rate, packet loss rate, and etc.
TraceRT: Measure delay rate, packet loss rate at network
route.
Destination Enter IP Address and URL for Ping test.
Timeout (ms) Enter timeout in milliseconds to wait for each reply (Unit:
ms).
TTL (1 ~ 255) Enter Time to live.
Packet Len (Bytes) Size of Data Byte to be transmitted.
Count Enter ICMP request count.
Set “Don’t
Fragment”
Send un-fragmented packet.
Reactivation Test Measure transition time of test mobile from a dormant
XCAL User Guide Chapter 5. AutoCall Setting
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 73
Classification Description
condition.
1. Select Classification – Single Ping.
2. Enter Destination, Timeout, TTL, Packet Len, Count
(Set over 2).
3. Check Reactivation Test.
4. Enter Count and Delay for Repeat.
Count: Ping repetition count
Delay(s): Time interval (sec) between repetitions
NOTE: Suppose you set Count and Delay as follows;
Count: 3, Delay(s): 40
Measure mode transition time for three times that test
mobile in Dormant mode is kept for 40 seconds after
Traffic Start, and change the mode to Active.
NOTE: In order to avoid Drop Event due to EVDO
connection close message, check Allow Dormant State
for Dormant Mode. (For detailed information of Dormant
Mode, refer to AutoCall Setting – AutoCall Setup -
Dormant Mode.)
3GPP QoS and APN Refer to 3GPP TS 27.007 (http://www.3gpp.org/).
XCAL User Guide Chapter 5. AutoCall Setting
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 74
HTTP
Set for HTTP call test.
HTTP Call setting
The detailed description of each item for HTTP call setting is as follows.
Classification Description
URL Enter HTTP Address to connect.
Repeat Enter number of access attempt to HTTP address to connect.
Pending If measured throughput meets the condition which user sets,
pending event is occurred. Upon pending, XCAL stops the
current call and start next call.
PPP/Ethernet: Select whether the pending condition will be
applied to PPP/Ethernet layer throughput.
FTP: Select whether the pending condition will be applied to
FTP (application) layer throughput.
Start Time (sec): The duration between the traffic start
time and when pending condition starts to be measured.
Interval (sec): If the throughput value remains under the
defined threshold value for the defined interval period,
pending event is declared and the call is terminated.
Threshold (Kbps): The desired throughput value in kbps
If throughput remains under the defined threshold value for
the defined interval period, pending event is declared and
XCAL User Guide Chapter 5. AutoCall Setting
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 75
the call is terminated.
3GPP QoS and APN Refer to 3GPP TS 27.007. (http://www.3gpp.org/)
XCAL User Guide Chapter 5. AutoCall Setting
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 76
Report
Generate a report in HTML format which summarizes the data measured.
Report shows the result of Autocall statistics regarding Current Mobile and All
Mobiles. The results which include the information and figures about each
scenario will be separated into the statistics window like overall calls and each
call, and it will be shown as table and graph. This information can be saved
for further use.
1. After AutoCall is terminated, click Report icon in
Statistics/Status – Call Statistics (All Scenarios) window.
2. Report Option window appears.
Report Option window
The detailed information of each item in Report Option window is as
follows.
XCAL User Guide Chapter 5. AutoCall Setting
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 77
Classification Description
Current Mobile Create an AutoCall report for the current test mobile.
All Mobile Create an AutoCall report for all test mobiles.
Company logo Add company logo in report to be created.
Width/Height Set width and height of company logo.
Prepared by Add name of writer.
use pattern Add graph pattern.
Throughput Select Throughput and RTT Time.
Min / Comp / Max /
Color
Select range and color for each parameter.
Add range.
Generate Create report.
Cancel Cancel report.
3. A report is created based on the setting.
XCAL User Guide Chapter 5. AutoCall Setting
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 78
Copyright by Innowireless Co., Ltd. Page 79
Real Time Mapping
User can view the test results on the Real Time Mapping window. The results are
displayed on the map graphically. Real Time Mapping window can display call event
and serving line between the active base stations and the current position of the
mobile.
Real Time Mapping window
1. Select Menu Bar File – Real Time Mapping, or press shortcut key Ctrl + R on
your keyboard. Or click on Map icon from Icon Bar.
2. Real Time Mapping window appears.
XCAL User Guide Chapter 6. Real Time Mapping
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 80
Real Time Mapping window
The detailed description of each item in Real Time Mapping window is as
follows.
Classification Description
Map Control Icon Icons for real time mapping.
For detail, refer to Real Time Mapping - Map Control Icon.
Enable Trace
Display GPS data extracted from existing logging file.
You may test along the existing test route.
For detail, refer to Real Time Mapping - Trace.
Phone Tab &
Parameter Selection
Box
Select parameters to be shown on the map.
Legend Display Box Display the selected parameter’s legend including range, color,
symbol, shape, and etc.
You may change legend setting by using Map Layer Property
icon.
Real Time Parameter Display the selected parameters in Parameter Selection in
XCAL User Guide Chapter 6. Real Time Mapping
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 81
Classification Description
Display Box table.
GPS Info Show GPS longitude and latitude of the current point and
mobile speed (km/h).
3. Measured data is displayed on map in real time.
XCAL User Guide Chapter 6. Real Time Mapping
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 82
Map Control Icon
Map Control Icon is used for map management (load map and change map
properties) and to set the measurement data display properties such as color,
symbol and location offset.
Icon Name Description
Map Layer
Property
Set parameter range, color and BTS/Repeater
connection.
For detail, refer to Real Time Mapping - Map
Layer Property.
Clear Remove all data displayed on the map.
Fit Scale Move to the current point.
Zoom In/Out Zoom in/out the map.
Pause Pause measurement data displayed on the map in
real time.
Technology Select relevant technology.
Enable Trace Trace GPs.
Display GPS information extracted from an existing
logging file.
For detail, refer to Real Time Mapping - Trace.
Map Mark
Open/Save
Save/Import mark information displayed on map.
Map Mark
Show/Hide
Show/Hide mark information display on map.
Bird View Display map looking straight down.
3D Building Display buildings on the map in three dimention.
XCAL User Guide Chapter 6. Real Time Mapping
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 83
Icon Name Description
Rotate Rotate map and change location.
Tracking Head Move map keeping point north side.
Trace Save GPS information in txt format automatically.
Display measurement route by using txt file.
You may remove txt file by using Delete button.
Parameter Tree Display parameter tree on the right side.
Parameter Tree Display parameter tree on the bottom.
Export to Google
Earth
Export in *.kml format to import to Google Earth.
XCAL User Guide Chapter 6. Real Time Mapping
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 84
Map Layer Property
Map Layer Properties window enables you to configure RF parameters to be
shown on real time map and set BTS/Repeater.
Click on May Layer Property icon in Real Time Mapping window.
Map Properties window appears.
Map Properties window is shown vary depending on map type (Map Selection).
Map (SmartMap)
Set map setting for Real Time Mapping window.
Map Properties_Map tab
XCAL User Guide Chapter 6. Real Time Mapping
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 85
The detailed description of each item in Map tab is as follows.
Classification Description
Offset setting Move measurement data to the designated longitude/latitude
position.
Map Selection Select map type.
Map type may vary depending on products.
Using image file: Insert any image to display instead of
map data. Click on icon to import image and set by
mouse menu.
Using image file mouse menu
Set Base Position: Shift the test route.
Set Relative Position: Balance test route and image file on
the map.
Reset Position: Adjust image file on the window size and
move test route to center.
Map layer Display TAB and MIF map type.
Support WGS84 type only.
XCAL User Guide Chapter 6. Real Time Mapping
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 86
Map (MIF)
Set map setting for Real Time Mapping window.
Map Properties_Map tab
The detailed description of each item in Map tab is as follows.
Classification Description
Offset setting Move measurement data to the designated longitude/latitude
position.
Map Selection Select map type.
Map type may vary depending on products.
Using image file: Insert any image to display instead of
map data. Click on icon to import image and set by
mouse menu.
Using image file mouse menu
XCAL User Guide Chapter 6. Real Time Mapping
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 87
Classification Description
Set Base Position: Shift the test route.
Set Relative Position: Balance test route and image file on
the map.
Reset Position: Adjust image file on the window size and
move test route to center.
Map layer Map Manager to create GEO file with MIF file: Convert
MIP map file in GEO format. MIF map supports GEO format
only.
GEO File: Import GEO file from the designated path.
1. Click on Map Manager to create GEO file with MIF
file button. Map Manager window appears.
2. Select a MIF file, and drag it into Select Files section on
the right side.
3. Enter a file name in Map Name entry field.
4. Click on Create button to create map file.
5. Click on icon from GEO File to import the created
GEO file.
6. Click on Map Property button. Map Control window
appears. You may allocate buildings and roads.
XCAL User Guide Chapter 6. Real Time Mapping
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 88
Classification Description
XCAL User Guide Chapter 6. Real Time Mapping
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 89
MAP (MapX)
Set map setting for Real Time Mapping window.
Map Properties_Map tab
The detailed description of each item in Map tab is as follows.
Classification Description
Offset setting Move measurement data to the designated longitude/latitude
position.
Map Selection Select map type.
Map type may vary depending on products.
Using image file: Insert any image to display instead of
map data. Click on icon to import image and set by
mouse menu.
Using image file mouse menu
XCAL User Guide Chapter 6. Real Time Mapping
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 90
Classification Description
Set Base Position: Shift the test route.
Set Relative Position: Balance test route and image file on
the map.
Reset Position: Adjust image file on the window size and
move test route to center.
Map layer Map Manger to use MapX File: Apply MapX file. Select a
map file you want to use for GeoSet, and click OK button.
XCAL User Guide Chapter 6. Real Time Mapping
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 91
BTS
Set BTS information on the map. Each class can be shown or hidden, and can
have different border width and color.
Map Properties_BTS tab
The detailed description of each item in BTS tab is as follows.
Classification Description
Boarder Setting Show/Hide BTS or Repeater depending on technologies.
Set band, boarder width, border color, and BTS size.
If two BTS are located at a point, XCAL displays the smaller
BTS over the larder one.
BTS/Repeater Label Set BTS/Repeater name color and font type.
Display Label Option Set BTS information and parameters to be shown on the
map.
XCAL User Guide Chapter 6. Real Time Mapping
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 92
Repeater
Show and hide link of the repeater and Mother BTS using check box. User can
set repeater link, font and background color.
Map Properties_Repeater tab
The detailed description of each item in Repeater tab is as follows.
Classification Description
Show Repeater Display repeater on the map.
Show Link between
Repeater and Mother
BTS
Display connection link between BTS and repeater.
Select BTS-Repeater
Link Parameter
Set base parameter for BTS and Repeater connection link.
Repeater Label Set alphabet which stands for Repeater on the map.
XCAL User Guide Chapter 6. Real Time Mapping
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 93
Classification Description
Serving Line
Serving lines to the Active, Candidate, Neighbor Set are indicated with
different colors according to the technology type and Ec/Io or RSSI threshold.
User can adjust them in this window.
Map Properties_Serving Line tab
XCAL User Guide Chapter 6. Real Time Mapping
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 94
Custom Draw
Set polyline, polygone label for marks on the map.
Map Properties_Custome Draw tab
XCAL User Guide Chapter 6. Real Time Mapping
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 95
ETC
Set distance unit (Km, Mile).
Map Properties_ETC tab
The detailed description of each item in ETC tab is as follows.
Classification Description
Show WCDMA Event Display WCDMA event.
Distance Unit Display disntance between measured data and
BTS/Repeater in Kilometer or Mile.
Scale Enter monitor size.
XCAL User Guide Chapter 6. Real Time Mapping
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 96
Coverage
Set color and line for BTS coverage.
Map Properties_Coverage tab
BTS coverage is shown as follows.
XCAL User Guide Chapter 6. Real Time Mapping
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 97
Legend
Set legend range and symbol type and size for each RF parameter.
Map Properties_Legend tab
The detailed description of each item in Legend tab is as follows.
Classification Description
Parameter tree Select a parameter you want to set legend.
Range value Double click and change value.
Copy from other
parameter
Copy another parameter’s setting for the selected parameter.
Select a parameter you want to copy setting, and the setting
is applied to the current parameter.
Batch range
Set all ranges in a parameter at once. Enter value in Step
entry field and values between Min and Max are ranged by
Step value.
Delete all range
Delete the current settings.
XCAL User Guide Chapter 6. Real Time Mapping
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 98
Classification Description
Add range
Add a new range line.
Delete range
Delete the selected line.
Save
Save the current setting in lgd format.
Load
Import existing lgd file.
Show Call Event Select call event you want to display on the map.
Import Analyzer
Legend
Import analyzer legend setting.
Export Analyzer
Legend
Save to apply for analyzer legend setting.
XCAL User Guide Chapter 6. Real Time Mapping
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 99
Trace
Extract GPS data from existing logging data and display them on the real time map.
It enables you to make sure test route of existing logging file and test along the
existing test route.
1. Select Enable Trace icon in Real Time Mapping window.
2. Load GPS Info window appears.
Load GPS Info window
3. Click Open icon from Extract GPS Info – Logging File. Select logging file
you want to extract GPS information.
4. Click Open icon from Extract GPS Info – Gps File. Select GPS export
path.
5. Click icon to create a file with GPS information.
The status bar shows its progress.
6. If you want to extract GPS information from more than one logging files, repeat
step 3 through 4.
7. Click Add button. The converted GPS file is added to GPS File list.
XCAL User Guide Chapter 6. Real Time Mapping
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 100
8. Click OK.
9. Loaded GPS route is displayed with red line in Real Time Mapping window.
You may make sure start and end point of the route.
XCAL User Guide Chapter 6. Real Time Mapping
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 101
Real Time Mapping mouse menu
Real Time Mapping mouse menu selects a certain point and set further settings.
1. Right click on Real Time Mapping window.
2. Real Time Mapping mouse menu appears.
Real Time Mapping mouse menu
XCAL User Guide Chapter 6. Real Time Mapping
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 102
Add Symbol/Polyline/Circle/Polygon
Display a certain point with symbol, polyline, circle, or polygon.
1. Right click on Real Time Mapping window, select among Add Symbol,
Add Polyline, Add Circle, or Add Polygon.
2. Select any range you want to display with polyline, circle, polygon on real
time map.
3. Right click to stop selecting the range.
4. Map Mark Input window appears.
If you selected on Add Symbol from Real Time Maping mouse menu,
Map Mark Input window appears without selection on the map.
Map Mark Input window
XCAL User Guide Chapter 6. Real Time Mapping
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 103
5. Set for Symbol, Polygon, Circle, Polygon configuration.
The detailed description of each item in Map Mark Input window is as
follows.
Classification Description
Alias Select a Alias name set from Mobile Alias Setting window.
For detailed description for Mobile Alias Setting window,
refer to Mobile Alias Setting.
Area Enter measurement area name.
Longitude/Latit
ude
Enter longitude and latitude automatically.
Memo 1,2,3 Enter memo.
7. Map displays with symbol, polyline, circle, polygon.
XCAL User Guide Chapter 6. Real Time Mapping
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 104
Mark List
Mark List window enables you to make sure all symbol, polyline, circle,
polygon information displayed on the map.
There are four tabs for Symbol, Polyline, Circle, Polygon.
You may show/hide each item by selecting each show/hide checkboxes.
Map Mark List window
The detailed description of each item in Map Mark List window is as follows.
Classification Description
Search Select Alias or Area from all list.
Show/Hide Show/Hide the selected items.
Select All Select all items in the list.
Unselect All Unselect all items in the list.
Import Import existing mark list.
Export Export mark list in txt.
XCAL User Guide Chapter 6. Real Time Mapping
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 105
Classification Description
Delete All Delete all mark lists.
OK Apply all setting and close Mark List window.
Alias Setting
Set symbol, polyline, circle, polygon to be displayed on the map.
1. Right click on Real Time Mapping window and select on Alias Setting.
2. Map Mark Alias Setting window appears.
Map Mark Alias Setting window
3. Click Add.
4. Enter Alias name. A new alias name is added on Alias list.
XCAL User Guide Chapter 6. Real Time Mapping
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 106
5. Double click on Preview button and set color, type, width.
Preview window
6. Click OK.
Copyright by Innowireless Co., Ltd. Page 107
Message
Signaling Message
Signaling Message window shows Layer3 messages transffered from test mobile.
1. Select Menu Bar - Message – Signaling Message.
2. Signaling Message (Mobile#) window appears.
Signaling Message (Mobile#) window
The detailed description of each item in Map tab is as follows.
Classification Description
Message Filter Click Filtering button to select filter name.
Filtered Message window shows the filtered message flow.
Filtering Add/Delete/Edit message filter.
1. Click Filtering button.
2. Message Filtering Dialog window appears.
XCAL User Guide Chapter 7. Message
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 108
Classification Description
3. Click New button. Enter message filter name in Filter Name
entry field.
4. Select message type you want to filter. Click Add.
5. Click OK.
Pause/Resume Pause/Resume message flow.
If message flow is stopped by Pause button, messages are saved
while logging is in progress.
Export Export the current message in the viewer in txt format.
Packet Display packet message with CAI message.
Clear Delete all messages shown in the window.
Find Find message.
Show Step 1,2,3 For WCDMA only.
Display selected Step 1,2,3 parameter in real time.
Message window The upper left section in Signaling Message window.
Display signaling message.
Filtered Message
window
The lower left section in Signaling Message window.
Display the selected parameter inforamtion.
Detailed Message
Information
window
The right section in Signaling Message window.
Display parameter information of the selected message.
Time Show Time Stamp for CAI message flow.
Show Step For WCDMA only.
Display Show Step 1, 2, 3 messages.
Channel Show message transfer channel.
ID Show message ID.
Message Show message name.
XCAL User Guide Chapter 7. Message
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 109
Mobile Message
Display event status, signaling, and diagnostic messages generated during test
mobile operation.
1. Select Manu Bar - Message – Mobile Message.
2. Mobile Message (Mobile#) window appears.
Mobile Message (Mobile#) window
The detailed description of each item in Mobile Message (Mobile#) window is
as follows.
Classification Description
Level Filter Messages can be filtered by message level designated by this filter
File Filter Messages can be filtered by source code file where the messages
were generated
Export Control button to export the displayed content
Pause Control button to stop temporary display of the contents. The
button is toggle button
Time Time stamp information for messages
File Name Name of the source code file where the message was generated.
For event messages, this column reads Event
Line Line number in source code file where the message was generated.
XCAL User Guide Chapter 7. Message
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 110
For event messages, this column lists the event category
Level/SSID Priority level assigned to message
Message Plain text description of message
Alarm Event Manager
Monitor alarm event list.
1. Select Menu Bar - Message – Alarm Event Manager.
2. Alarm Event Manager (Mobile#) window appears.
Alarm Event Manager (Mobile#) window
The detailed description of each item in Alarm Event Manager (Mobile#)
window is as follows.
Classification Description
As Excel/Txt Export alarm event manager window in xls or txt.
Time Display time stamp of message.
Message Display event list which meet alarm condition.
XCAL User Guide Chapter 7. Message
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 111
Packet Message
Display message flow and detailed content of message of test mobile.
Packets which generated from test mobile during data service such as LCP, CHAP,
IPCP, IP, TCP, UDP, ICMP, and etc. are displayed in order.
1. Select Menu Bar - Message – Packet Message.
2. Packet Message (Mobile#) window appears.
Packet Message (Mobile#) window
The detailed description of each item in Packet Message (Mobile#) window is
as follows.
Classification Description
Pause/Resume Pause/Resume message flow.
Time Show time stamp of message.
Dir Show message flow direction.
Rx: Receive (Network > PC / MS)
Tx: Transmit (PC / MS > Network)
Type Show packet message type.
Code Show message name and Seq/ACK number.
Message display
window
The left section in Packet Message window.
Display packets which generated from test mobile during data
service such as LCP, CHAP, IPCP, IP, TCP, UDP, ICMP, and etc. are
XCAL User Guide Chapter 7. Message
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 112
Classification Description
displayed in order.
Protocol analysis
window
The right section in Packet Message window.
A protocol analyzer which analyzes captured packets and display
packet message.
NOTE: Supported depending on product version.
XCAL User Guide Chapter 7. Message
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 113
Packet Capture Viewer
Capture packet messages and display them in Packet Capture Viewer window.
1. Select Menu Bar - Message – Packet Capture Viewer.
2. Packet Capture Viewer (Mobile#) window appears.
Packet Capture Viewer (Mobile#) window
XCAL User Guide Chapter 7. Message
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 114
PPP Frame Message
Display PPP Frame information including UM/RM/AN Frame.
1. Select Menu Bar - Message – PPP Frame Message.
2. PPP Frame Message (Mobile#) window appears.
PPP Frame Message (Mobile#) window
Copyright by Innowireless Co., Ltd. Page 115
Statistics/Status
Call Statistics (Current Scenario)
Display call statistics of currently processed scenario.
Detailed call statistics including detailed fail reason, call procedure and information
(setup time, traffic time, IP address) are displayed.
1. Select Menu Bar - Statistics/Status – Call Statistics (Current Scenario).
2. Call Statistics (Current Scenario) window appears.
Call Statistics (Current Scenario) window
XCAL User Guide Chapter 8. Statistics/Status
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 116
Call Statistics window has All Info and Detailed Info tabs.
All Info
Display call statistics, procedure, information of test mobile.
All Info tab displays different statistics items depending on Call Type (Voice,
Data Call).
Voice
Call statistics window for Voice call.
Call Statistics (Current Scenario) window_All Info tab
The detailed description of each item in Call Statistics (Current Scenario)
XCAL User Guide Chapter 8. Statistics/Status
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 117
window is as follows.
Classification Description
Scenario Shows the current scenario name (current count/total retry
count) to run
Phone Info Mobile Type(shows chip type and mobile type)
Total The number of calls progressed/Total number of calls for auto
call test
Success The number and percentage of successful calls for attempted
calls
Setup Fail The number of setup fail calls (Setup fail occurs when radio
link setup failure happens)
Drop Call drop during progress of traffic
End By C.P Disconnect by Counter party (release or drop)
*This event is available for Voice and CS
End By M.R Call disconnected by mobile, after traffic.
Idle * CDMA : Fail to receive general page message
* WCDMA : Fail to receive rrc Connection Request message
Error Number of calls with various errors such as No ATDT, modem
Error and port error. These errors are related to test phone
Time Idle time/Setup time/Traffic setup time/Traffic time
Work Type Autocall type such as FTP Up/Down state, Ping, HTTP and CS
Progress It displays the progress of the current call
Current State Indicate current state of application service
Call Result Result of call
XCAL User Guide Chapter 8. Statistics/Status
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 118
Data (FTP, PPP, Ping, HTTP)
Call statistics window for Data (FTP, PPP, Ping, HTTP) call.
Call Statistics (Current Scenario) window
The detailed description of each item in Call Statistics (Current Scenario)
window is as follows.
Classification Description
Scenario Shows the current scenario name (current count/total retry
count) to run
Phone Info Mobile Type(shows chip type and mobile type)
Total The number of calls progressed/Total number of calls for auto
call test
Success The number and percentage of successful calls for attempted
calls
Setup Fail Setup fail occurs when radio link setup failure happens
XCAL User Guide Chapter 8. Statistics/Status
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 119
Classification Description
Traffic Fail Traffic fail is declared if connection to application layer fails
after finishing PPP layer connection.
*This event is available for data service such as FTP, TFTP
and HTTP
Drop Call drop during progress of traffic
Pending If throughput is sustained under predefined threshold for
designated time threshold, then pending is declared and the
call will be dropped
NOTE: For detail, refer to AutoCall Setting – AutoCall
Setup – AutoCall Type – FTP.
Time Out If download or upload from/to application can not be finished
during predefined traffic time interval, then Time Out is
declared
Error Number of calls with various errors such as No ATDT, modem
Error and port error. These errors are related to test phone.
Time Idle time/Setup time/Traffic setup time/Traffic time
Setup(A / C / S) Connection Time for Air link setup time/Core link setup
time/Server setup time
CDMA
Air Time: ATDT ~ LCP Start(Traffic)
Core Time: LCP Start(Traffic) ~ IPCP End
Server Time: FTP Connecting ~ FTP Load CMD
WCDMA
Air Time: ATDT ~ RRC Connection Complete
Core Time: RRC Connection Complete ~ Activate PDP
Context Accept
Server Time: FTP Connection ~ FTP Load CMD
GSM
Air Time: ATDT ~ PDP Context Request
Core Time: Activate PDP Context Request ~
Activate PDP Context Accept
Server Time: FTP Connection ~ FTP Load CMD
Current Display throughput of proceeding call
Avr_Time(Kbps) Average throughput of calls averaged over time
XCAL User Guide Chapter 8. Statistics/Status
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 120
Classification Description
Avr_Call(Kbps) It is calculated as follows; Total received bytes / Total elapsed
times of all FTP transmission
Work Type Display current call type
Work Info1 IP address of application server before starting service
application. File size to be downloaded or uploaded after
starting service application
Work Info2 File name to be downloaded or uploaded before starting
service application. Amount of data downloaded or uploaded
after starting service application
Progress Indicate percentage of data quantity downloaded or uploaded
over total file size
Current State Indicate current state of application service
Call Result Result of call
XCAL User Guide Chapter 8. Statistics/Status
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 121
Detailed Info
Display call statistics, procedure, event.
Detailed Info window consists of the following three sectinos.
Call Statistics View
Call Result View
Call Event History View
Call Statistics (Current Scenario)_Detailed Info tab
Call Statistics View
Show the statistics of call result over the current auto call scenario such as
success rate, setup fail rate, traffic fail rate, drop rate and the specific
reason of failed calls.
Call Statistics View
Call Result View
Call Event History View
XCAL User Guide Chapter 8. Statistics/Status
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 122
Call Statistics View
The detailed description of each item in Call Statistics View is as follows.
Classification Description
AutoCall Setting
Call Type Call Type ( Voice, FTP…)
Idle Time Time interval between two successive calls
Setup Time
Time limit for the test phone to connect to Dial-Up Network. If the
test phone cannot be connected to Dial-Up Network until the
Setup Time expires, XCAL counts it as fail call.
Traffic Setup
Time
Duration from connecting to the FTP site to completion of
downloading. If the call is dropped in the middle of the call before
the Traffic setup Time expires, XCAL counts it as drop call.
Traffic No of calls successfully completed downloading during traffic time
Call summary
Total The number of calls progressed/Total number of calls for auto call
test.
Success The number and percentage of successful calls for attempted calls.
Setup Fail Setup fail occurs when radio link setup failure happens.
Traffic Fail Traffic fail is declared if connection to application layer fails after
finishing PPP layer connection
*This event is available for data service such as FTP, TFTP and
HTTP.
Drop Call drop during progress of traffic
Pending If throughput is sustained under predefined threshold for
designated time threshold, then pending is declared the call will be
dropped.
*This event is available for FTP.
Time Out If down load or up load from/to application can not be finished
during predefined traffic time interval, Time Out is declared.
*This event is available for FTP.
End By C.P The number of calls progressed/Total number of calls for auto call
test.
Idle * CDMA : Fail to receive page response message
* WCDMA : Fail to receive rrc Connection Request message
Error Number of calls with error
Congestion Receive mobile is on line.
No Service Fail to receive service connect message
XCAL User Guide Chapter 8. Statistics/Status
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 123
Classification Description
Fail Reason
Voice Call Setup Fail Reason (CDMA)
Origination
Fail
Fail to send origination message within setup time in origination
type call
Channel
Assign
Fail N
Fail to receive channel assignment message.
N is number of Origination of Page Response Messages
No Service Fail to receive service connect message
BS Ack Fail Fail to receive base station acknowledgement message after
receiving channel assignment message
Alert Fail Fail to receive alert message
Connect Setup fail occurred after alert Message is received
Voice Call Setup Fail Reason (WCDMA)
Origination Fail to send origination message within setup time in origination
type call
RRC Reject Fail to setup call by receiving RRC connection reject message
RRC phase Fail to receive RRC Connection Complete message
CM Setup
phase
Fail to receive Downlink Direct Transfer(Call Proceeding) message
after receiving Initial Direct Transfer(CM Service request) message
RAB
Failure
Fail to setup call by receiving Radio Bearer Failure message
RAB Setup
phase
Fail to receive Radio Bearer Setup Complete message after
receiving Radio Bearer Setup Message
Alerting
phase
Fail to receive Alerting Connection and Connection Ack message
after receiving Radio Bearer setup complete message
Disconnect Fail to setup call by receiving Downlink direct transfer(Disconnect)
message
Registratio
n Failure
Fail to setup call due to RT Area Update
Network
Busy
Receive mobile is on line.
Data Call_Setup Fail Reason
Dial Fail Dial fail is declared if radio link can’t be set up during setup time
threshold.
XCAL User Guide Chapter 8. Statistics/Status
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 124
Classification Description
LCP Fail LCP fail is declared if LCP negotiation phase can’t be finished
before setup timer expires.
Auth Fail Auth fail is declared if authentication negotiation phase can’t be
finished before setup timer expires.
IPCP Fail IPCP fail is declared if clients can’t receive IP allocation from
network before setup timer expires.
Logon Fail Logon fail is declared if network Logon can’t be finished before
setup timer expires.
Data Call_Traffic Fail Reason
Connect Fail Fail to connect to application server before traffic setup timer
expires.
Change Dir
Fail
Fail to locate directory of application server where download file
is located before traffic setup timer expires.
File Open Fail Fail to open download file before traffic setup timer expires.
Time out Fail Fail to start download before traffic setup timer expires.
Data Call_Ping Statistics
Lost (%) Percentage of lost ping count over total ping count in total call
Min (ms) Min RTT value in ms over total call
Max (ms) Max RTT value in ms over total call
Avg (ms) Average RTT value over total call
Hops (Min) Min hop count over total call
Hops (Max) Max hop count over total call
Call Result View
Show summarized results of each call such as setup time, FA, End Time,
Result, FA, SID, NID, Scenario, Call Type and Information.
Call Result View
XCAL User Guide Chapter 8. Statistics/Status
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 125
The detailed description of each item in Call Result View is as follows.
Classification Description
No Number of call
Start Time Start time of call
End Time End time of call
Result Reason of call termination
Scenario Scenario name
Call Type Call Type (Voice, FTP, HTTP and Ping/TraceRT)
Throughput Displays the information depending on the scenario
Info Number of call
Summarized result in call.
Classification Description
Common * D (Dial Time) : ATDT ~ LCP Start (First)
* L (LCP) : LCP Start (Traffic) ~ LCP Complete
* A (Auth) : Auth Start ~ Auth Complete
* I (IPCP) : IPCP Start ~ IPCP End
* P (PPP) : LCP Start (First) ~ IPCP End
* L (Logon) : PPP Logon Start ~ PPP Logon End
CDMA FA : Frequency Assignment.(Invalid on WCDMA)
SID : System Identification number(Invalid on
WCDMA)
NID : Network Identification number(Invalid on
WCDMA)
Voice CDMA Setup: Elapsed time to setup radio link
WCDMA Setup: Elapsed time to setup radio link
RRC : RRC Connection request ~ RRC Connection
Setup Complete
CM Setup : CM Service request ~ Call Proceeding
RAB : Radio Bearer Setup ~ Radio Bearer Setup
Complete
RRC No : RRC Connection request Count
FTP Server Elapsed time for FTP Connection
Traffic Elapsed time for traffic
Throughp
ut
Throughput of FTP application layer
RcvByte Amount of total received bytes for a call
XCAL User Guide Chapter 8. Statistics/Status
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 126
Classification Description
MaxByte Maximum size of file to be received in byte unit for a
call
Air, Core Air, Core Time.
For detailed information for Air Time/Core Time, refer
to Statistics/Status – Call Statistics (Current
Scenario) - All Info.
Ping RTT(Min) Minimum RTT in a call
RTT(Max) Maximum RTT in a call
RTT(Avg) Average RTT of a call
Rcv Number of receive
Lost Number of ping lost in a call and percentage of lost
ping count over total sent ping count in a call
XCAL User Guide Chapter 8. Statistics/Status
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 127
Call Event History View
Show history of important events in call processing with timestamp. It displays
the important call event with timestamp.
Call Event History View
The detailed description of each item in Call Event History View is as follows.
Classification Description
Time Time information of events.
Status Detailed status of call in progress.
Contents Supplemental information for status.
XCAL User Guide Chapter 8. Statistics/Status
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 128
Call Statistics (All Scenario)
Display overall statistics of all AutoCall scenarios.
1. Select Menu Bar - Statistics/Status – Call Statistics (All Scenarios).
2. Call Statistics (All Scenarios) window appears.
Call Statistics (All Scenarios) window
The detailed description of each item in Call Statistics (All Scenarios) window is
as follows.
Classification Description
Scenario Current scenario name
Call Type Current call type
Repeat Repeatition count of AutoCall scenario.
Total The number of calls progressed for current call/Total number of calls for
current auto call test.
(If user uses the Setup Try function, the total is PPP setup count.)
Setup Try Repeat count of auto call scenario
Success Number of successful calls
Setup Fail Setup fail occurs after radio link setup failure
Incomplete Number of calls which are not successful. This parameter is for data
service only.
Error The number and percentage of error calls for attempted calls
XCAL User Guide Chapter 8. Statistics/Status
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 129
EVDO Session Assignment Test
EVDO Session Clear function is done automatically using N/W Read/Write function..
1. Select Menu Bar - Statistics/Status – EVDO Session Assignment Test.
2. Set values and click Session Clear button. The following items are displayed and
the test mobile is reset.
Classification Description
Mobile Mobile Number
SPC Displays the code in SPC
Session Clear Resets the mobile
XCAL User Guide Chapter 8. Statistics/Status
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 130
Ping Status
Display single ping test result in graph and statistics.
1. Select Menu Bar – Statistics/Status – Ping Status.
XCAL User Guide Chapter 8. Statistics/Status
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 131
TraceRT Status
Display TraceRT test result in statistics.
1. Select Menu Bar - Statistics / Status – TraceRT Status.
Classification Description
TTL Time to Live
IP IP Address
Cur (ms) Displays RTT of current IP
Min (ms) Displays minimum RTT
Max (ms) Displays maximum RTT
Avg (ms) Displays average RTT
Max-Min (ms) Max RTT – Min RTT
XCAL User Guide Chapter 8. Statistics/Status
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 132
Throughput Info
Display throughput information.
1. Select Menu Bar - Statistics/Status – Throughput Info.
Classification Description
PPP Throughput Displays throughput in PPP layer
IP Throughput Throughput in IP layer that includes IP Header
TCP / UDP
Throughput
Throughput in TCP and UDP layer
APP Throughput Throughput of Specific port TCP
* FTP: 20, HTTP: 80
TCP
Retransmission
Rate
Provides TCP retransmission rate
TCP Window Size Buffer Window Size
Tx Throughput Provides PPP, IP, TCP / UDP, APP Tx Throughput
Rx Throughput Provides PPP, IP, TCP / UDP, APP Rx Throughput
XCAL User Guide Chapter 8. Statistics/Status
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 133
GPS Status
Display location and time information received from GPS.
1. Select Menu Bar - Statistics/Status – GPS Status.
Classification Description
GPS Time Current time information provided by GPS.
Longitude Longitudinal location information provided by GPS.
Latitude Latitudinal location information provided by GPS.
Heading Orientation of movement.
Speed Current moving speed.
Source A textual evaluation of the current signal being received by the GPS
receiver. Possible values are: (GPS receiver does not report quality,
mostly for ETAK receiver support), (bad reception, so no GPS position
can be derived), (Standard), (a usable signal from a standard GPS
receiver, accurate within 50 meters), (good signal from a differential
GPS receiver, so the reported position is especially accurate within 5
meters)
Data Age An indicator of the freshness of the GPS data: either Valid or Stale.
XCAL User Guide Chapter 8. Statistics/Status
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 134
GPS Satellite Status
Display satellite location information received from GPS.
1. Select Menu Bar - Statistics/Status – GPS Satellite Status.
Classification Description
Satellite The number of satellites , GPS is receiving signal currently from
PNR Satellite ID
Elevation Elevation information of satellite
Azimuth Azimuth information of satellite
C / N Carrier to Noise ratio of the satellite signal
XCAL User Guide Chapter 8. Statistics/Status
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 135
Logging Info
Display where logging file for the test mobile to be saved.
1. Select Menu Bar - Statistics/Status – Logging Info.
Classification Description
Directory The name of the directory the drive test file is being saved.
File Name Designated name for the drive test file.
Start Time Start time of logging the drive test data.
Elapsed Time Elapsed time from the start of logging.
Logging Size Size of drive test file.
Disk Free Space Free space of hard disk.
XCAL User Guide Chapter 8. Statistics/Status
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 136
Communication Statistics
Display packet CRC error in statistics.
1. Select Menu Bar - Statistics/Status – Communication Statistics.
Classification Description
Comport Designates communication port
BaudRate Designates communication speed through DM port
Streaming Determine if streaming logging is executed
# of Tx Packet Count of Total Tx Packet
# of Rx Packet Count of Total Rx Packet
# of CRC Error Count of Packet Error
XCAL User Guide Chapter 8. Statistics/Status
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 137
QPCH Statistics
Display QPCH parameter and QPCH of test mobile.
1. Select Menu Bar - Statistics/Status – QPCH Statistics.
Classification Description
Channel Provides QPCH Walsh channel
Rate Least significant bit – RATE; rate for QPCH paging indicators:
0 – 4800 bps
1 – 9600 bps
Upper seven bits – XFER_REASON; QPCH transfer reason
(why QPCH could transfer back to idle):
0 – QPCH_NO_XFER
1 – QPCH_SLOT_IMMINENT
2 – QPCH_MC_NOT_VALID
3 – QPCH_CH_EST_BAD_SIGNAL
4 – QPCH_XFER_BCAST_DATA
5 – QPCH_BP_AND_PG
6 – QPCH_BP_NOT_SUPPORTED
7 – QPCH_RWUP
8 – QPCH_PI1_PI2_ON
XCAL User Guide Chapter 8. Statistics/Status
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 138
Classification Description
9 – QPCH_BI1_BI2_ON
10 – QPCH_NEXT_SLOT_NOT_SUPPORTED
11 – QPCH_CCI_HANDOFF
12 – QPCH_CCI_ON
13 – QPCH_DISABLE_BIO_SWITCH
PN PN index of Pilot (0..511)
Power Level Power level for paging indicator (0~7)
000 – 5 dB below Pilot Channel Transmit Power
001 – 4 dB below Pilot Channel Transmit Power
010 – 3 dB below Pilot Channel Transmit Power
011 – 2 dB below Pilot Channel Transmit Power
100 – 1 dB below Pilot Channel Transmit Power
101 – Same as Pilot Channel Transmit Power
110 – 1 dB above Pilot Channel Transmit Power
111 – 2 dB above Pilot Channel Transmit Power
Erasure
Threshold
Threshold used to determine if the PI / CCI bit is an erasure
Bit Threshold Threshold used to determine if the PI / CCI bit is 1 or 0
Type Type of indicator (0~5)
0 – Paging Indicator #1
1 – Paging Indicator #2
2 – Configuration Change Indicator #1
3 – Configuration Change Indicator #2
4 – Broadcast Indicator #1
5 – Broadcast Indicator #2
Status Result of indicator demodulation (0~4)
0 – Not applicable
1 – Not detected
2 – Detected
3 – Erasure
4 – Missed
Bit Position Position of indicator (0~768)
I-channel Bit
Energy
Indicator energy on I Channel (0~65535)
Q-channel Bit
Energy
Indicator energy on Q Channel (0~65535)
I-channel Pilot
Energy
Common pilot energy (0~65535)
XCAL User Guide Chapter 8. Statistics/Status
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 139
Classification Description
Q-channel Pilot
Energy
Diversity pilot energy (0~65535)
Copyright by Innowireless Co., Ltd. Page 140
User Define
User Define menu allows you to make sure any parameters in table and graph.
Parameters for test mobile are displayed in Graph, Table, Summary Info, and Cell
Measurement windows.
User Define menu is supported depending on product.
Graph
Display parameter in graph.
1. Select Menu Bar - User Defined –Graph.
2. Select checkboxes for any parameters you want to display in graph from the
parameter tree on the left section or drag it into the graph on the right section.
3. Set maximum and X, Y axis value. Click Apply.
XCAL User Guide Chapter 9. User Define
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 141
4. Right click on Graph, and graph mouse menu appears.
Classification Description
Remove Deletes the chosen parameter
X Range Sets the range of X-axis of the Graph which displays the value of
the chosen parameter. (unit: second)
Create Favorite Saves the setting of the chosen parameter
Delete Favorite Deletes the Favorite File previously generated
Show Parameter
List
Check : Displays the parameter set-up window
Uncheck : Doesn’t show up the parameter set-up window
Show WCDMA
Alarm Event
Check: Displays Attempt, Success. and Fail on Graph when Event
Occurs
Uncheck: Doesn’t show Attempt, Success, and Fail on Graph when
Event Occurs
WCDMA Event Color
Setting
This option appears only when Show WCDMA Alarm Event is
selected.
Set attempt, success, fail color for WCDMA event.
Select WCDMA Event Color Setting, and Color Setting window
appears.
XCAL User Guide Chapter 9. User Define
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 142
Table
Display parameter in table.
1. Select Manu Bar - User Defined –Table.
2. Select checkboxes for any parameters you want to display in table from the
parameter tree on the left section or drag it into the graph on the right section.
3. Right click on Table, and table mouse menu appears.
Classification Description
Remove Deletes the chosen parameter
Create Favorite Saves the setting of the chosen parameter
Delete Favorite Deletes the Favorite file previously generated
Show Parameter
List
Check : Displays the parameter set-up window
Uncheck : Doesn’t show up parameter set-up window
Show WCDMA Check: Displays Attempt, Success. and Fail on Graph when Event
Occurs
XCAL User Guide Chapter 9. User Define
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 143
Alarm Event Uncheck: Doesn’t show Attempt, Success, and Fail on Graph when
Event Occurs
Summary Info
Display current information for selected parameter for each test mobile.
1. Select Menu Bar - User Defined – Summary Info.
2. Select checkboxes for any parameters you want to display in table from the
parameter tree on the left section or drag it into the graph on the right section.
3. Right click on the table and Summary Info mouse menu appears.
Classification Description
Remove Mobile Hide parameter.
Remove Parameter Delete parameter.
Show Parameter
List
Show/Hide parameter list section.
Create Favorite Save parameter selection setting in Favorite.
Parameter selection setting is added under Favorite tree.
XCAL User Guide Chapter 9. User Define
Accuver EMEA Ltd. Suite Two, 1st Floor, Congress House 14 Lyon Road, Harrow, Middlesex, HA1 2EN, UK Tel. +44 208 863 1118 Page 144
Delete Favorite Delete Favorite tree.
Cell Measurement
Display PN information by technology.
1. Select Menu Bar - User Defined – Cell Measurement.