wsd contract requirements for factory inspection of ... · bs 3601 chemical composition and...
TRANSCRIPT
1
Ir C K CheungHong Kong Institution of Certified Auditors
香港專業審核師學會
WSD Contract RequirementsFor Factory Inspection of
Waterworks Products
WSD Contract RequirementsFor Factory Inspection of
Waterworks Products
2
Definition of InspectionDefinition of Inspection
• Inspection
• Examination of a product design, product, service, process or plant, and determination of their conformity with specific requirements or, on the basis of professional judgement, general requirements.
3
Type of Inspection BodyType of Inspection Body
• Type A – 3rd party inspection
• Type B – inspection to its parent organization
• Type C – inspection to its own organization
4
Type of InspectionType of Inspection• 1. Pre-production Inspection• Inspection of pre-production against specifications of raw
materials• 2. During production Inspection• Inspection of a general manufacturing process-witnessing
of the production line & QC • Inspection of the manufacturing process in particular for
the purchased batch of products against the client’s specifications or standards
• 3. Pre-shipment Inspection• Inspection of the purchased products, with simple tests to
check compliance prior to shipment• 4. In-service Inspection• Inspection of cars and crane
5
WSD Products for Inspection
WSD Products for Inspection
• Water pipes – Steel, DI, Polyethylene, UPVC, lined GI & fittings
• Valves – CI, air relief, butterfly, non-return, copper alloy stop/gate valve
6
Factory Inspection ofSteel Pipes
BS EN 10224:2002BS EN 10311:2005
Factory Inspection ofSteel Pipes
BS EN 10224:2002BS EN 10311:2005
7
BS 534BS 534
8
WSD Spec for steel pipeWSD Spec for steel pipe
• BS EN 10221 and BS EN 10220• By Electric Resistance Welding (ERW)
or Submerged Arc Welding (SAW)• Mini tensile strength 430 MPa• Full length 8 m• Joint : flanged, slip-on coupling, collar
weld, spigot & socket welded joints
9
Steel pipe materialsSteel pipe materials
• Pipe to BS EN 10221 and BS EN 10220
• Pipe specials such as tee and collar to BS EN 10220
• Non-metallic products in contact with water to BS 6920: Part 1
10
Methods of making pipe bodyMethods of making pipe body
11
Butt welded steel pipeButt welded steel pipe
12
Electric resistance welded steel pipe
Electric resistance welded steel pipe
13
Seamless steel pipeSeamless steel pipe
14
Submerged arc welded steel pipeSubmerged arc welded steel pipe
15
Submerged-arc weldingSubmerged-arc welding
16
17
18
Different types of jointsDifferent types of joints
19
20
Coating for steel pipeCoating for steel pipe
21
22
Epoxy CoatingEpoxy Coating
23
Pipe protectionPipe protection
• External : Fusion bonded epoxy system to ANSI/AWWA C213 or chemically-cured liquid epoxy system to ANSI/AWWA C210, mini dry film thickness 400 microns
• Plus pipe exposed outdoor under direct sunlight, a topcoat of aliphatic polyurethane at 50 microns
• Internal : 400 micron to C213 but 750 micron to C210
24
Coating materialsCoating materials
• Coating material for internal lining tested to BS 6920, A certification by Water Research Centre of UK approval for contact with potable water suitable for human consumption or equivalent
• Ext & int : mini adhesion strength to ASTM D4541 19 MPa mini impact test to ASTM D2794 0.136 kgm, mini abrasion to ASTM D4060 200mg/1000rotation, loaded at 1000g
25
Lining for steel pipeLining for steel pipe
26
27
Concrete liningConcrete lining
28
Cement mortar lining
Cement mortar lining
29
BS 3601:1987BS 3601:1987
30
BS 3601 Chemical composition and Mechanical Propreties
BS 3601 Chemical composition and Mechanical Propreties
31
32
BS 3601 Mechanical propertyBS 3601 Mechanical property
33
BS 3601 Quality Control Testing by ManufacturerBS 3601 Quality Control Testing by Manufacturer
34
BS 3601 Mechanical TestsBS 3601 Mechanical Tests
35
Flattening TestFlattening Test
36
Hydraulic testHydraulic test
37
Eddy current test
Eddy current test
38
Test certificateTest certificate
39
Pipe MarkingPipe Marking
40
BS 3601 to be replaced by
BS EN 10224
BS 3601 to be replaced by
BS EN 10224
41
Chemical compositionChemical composition
42
Mechanical propertiesMechanical properties
43
44
45
NDT of weldsNDT of welds
46
Testing & Inspectionby Manufacturer
Testing & Inspectionby Manufacturer
• Test certificate to BS EN 10224:2002• 100% radiographic inspection may be
used in lieu of hydraulic test• All epoxy & plastic based coating to BS
6920 • All pipes & fittings shall be capable of
withstanding the max field hydrostatic test pressure specified.
47
48
BS 6920-1:2000BS 6920-1:2000
• Suitability of non-metallic products for use in contact with water intended for human consumption with regard to their effect on the quality of the water
• Specification
49
BS 6920-1:2000BS 6920-1:2000
• Odour and flavour of water• Appearance • Growth of aquatic microorganisms• Extraction of substances
50
WSD Spec for ductile iron pipeWSD Spec for ductile iron pipe
• Pipe to BSEN 545, gasket to BSEN 681-1 and pipe length 5.5m
• Unless specified, all pipe & fitting shall be hydraulic pressure rated 1.6MPa
• All maxi field test pressure 2.5 MPa• Liquid : potable, sea & treated effluent• Joint: spigot & socket, flanged
51
52
53
54
55
56
57
58
59
60
61
Testing & Inspection by Manufacturer
Testing & Inspection by Manufacturer
• Tensile test to BS 4772, Cl. 2.5.1 & 2• Straightness test to BS 4772• Work proof test• Hardness test• Gasket to BS 2494• Type test on welded-on flanges to BS
4772
62
Sampling procedure to BS6001Sampling procedure to BS6001Steel/Polyethylene/DI/UPVC/Lined GI Pipes, CI Gate Valves, Air Relief Valves and Copper Alloy Stop/Gate Valves (A) Water/Hydrostatic Pressure Test
(1) For lot size less than 20 No., the sample size shall be equal to the lot size. For lot size equal to or more than 20 No., the sample size shall be 20 No.
(2) Duration of tests for polyethylene pipes shall be in accordance with the relevant
specification. Duration of tests shall be 2 minutes for other pipes and shall be in accordance with BS 6755 : Part 1:1986 for valves.
(3) Tests shall be witnessed before any finishing treatment.
(4) Acceptance criteria shall be no failure of witnessed water/hydrostatic pressure tests.
63
(B) Other Tests (1) Sample size shall be determined in accordance with
BS 6001 : Part 1:1991 at inspection level II for single sampling plan. Materials from sub-contractors /different sources shall be sampled as isolated lots.
(2) Normal inspection shall be used at the start of inspection.
Inspection may be switched to tightened or reduced inspection and switched back to normal inspection in accordance with the procedures stipulated in Cl. 9.3 of BS 6001 : Part 1:1991.
(3) Acceptable quality level (AQL) shall be 4.0.
Sampling procedure to BS6001
64
65
Factory Inspection of Water Valves
BS 5150
Factory Inspection of Water Valves
BS 5150
Coating for CI valveCoating for CI valve
Coating All cast iron parts for all valves including those of nominal sizes above DN600 shall be coated with an epoxy or plastic based materials. The proposed coating shall be suitable for use in potable water and shall comply with the requirement of BS6920. The epoxy or plastic based coating shall comply with the performance requirement of WIS4-52-01. The following minimum thickness for epoxy coating shall apply:-
Electrostatically Fusion Powder Coated Epoxy
(µm)
Airless Sprayed Application
(µm) Flat and Pressurised Parts 250 400 Convex Outer Edges 150 300
Details of such coating and certificate from an independent laboratory/inspection authority shall also be submitted to the Engineer for consideration
Materials for CI valveMaterials for CI valve
Materials 10.1 The valve components shall be manufactured from the materials given, as
appropriate, in Table 1 of this Specification. 10.2 The alternative materials contained in Table 6 of BS 5163:1986 shall not,
except where expressly permitted above, be used without the prior approval of the Engineer.
10.3 The Contractor shall provide test certificates on chemical and mechanical properties of the materials from an approved laboratory to provide the necessary evidence of suitability.
Table 1 – Materials for valves
Component Category ‘RES’ (Resilient seated) Category ‘CF’ (copper alloy faced)
Material Ref. Grade of designation
Material Ref. Grade or designation
Body, bonnet, stufing box, stem seal hsg. Bridge
Spheroidal graphite cast iron
BS EN 1563 : 1997 EN-GJS-400-18, EN-GJS-450-10, EN-GJS-500-7
Spheroidal graphite cast iron
BS EN 1563 : 1997 EN-GJS-400-18, EN-GJS-450-10, EN-GJS-500-7
Handwheel, stem cap
Grey (flake graphite) cast iron
BS EN 1561 : 1997 EN-GJL-250, EN-GJL-300, EN-GJL-350
Grey (flake graphite) cast iron
BS EN 1561 : 1997 EN-GJL-250, EN-GJL-300, EN-GJL-350
Obturator with integral faces
Grey (flake graphite) cast iron
BS EN 1561 : 1997 EN-GJL-250, EN-GJL-300, EN-GJL-350
Copper alloy BS EN 1982 : 1999 CC491K CC492K CC331G
Obturator with separate facings
Grey (flake graphite) cast iron
BS EN 1561 : 1997 EN-GJL-250, EN-GJL-300, EN-GJL-350
Grey (flake graphite) cast iron
BS EN 1561 : 1997 EN-GJL-250, EN-GJL-300, EN-GJL-350
Obturator facing or lining
Resilient material BS EN 681-1 : 1996 Grades shall comply with the specific requirements for Type WA
Copper alloy BS EN 1982 : 1999 CC491K CC492K CC331G
Testing for CI valveTesting for CI valveTesting
11.1 Test requirements shall be as specified in BS 5163:1986 for valves of nominal
sizes up to DN600 and in BS 5150:1990 and BS 6755:Part 1:1986 for valves of nominal sizes above DN600 unless otherwise specified. Seat testing for all valves shall be carried out on both sides of an obturator under an open end condition.
11.2 Test Certificates are required for all valves. 11.3 All certificates for non-metallic materials showing compliance with BS 6920
issued by an independent laboratory/inspection authority must be submitted to the Engineer for consideration.
WSD Spec for air relief valveWSD Spec for air relief valve
• To BS 21, BS 1452, BS 4504, BS 5163• Small orifice air valve• Double orifice air valve• Material: Grey CI to BS 1452• Test to BS 5163
WSD Spec 150mm pedestal fire hydrant
WSD Spec 150mm pedestal fire hydrant
• Ferrous casting to BS 1452 grade 220 density > 7200kg/m3
• Non-ferrous casting: bronze to BS1400 with zinc content < 1%
• All hydrant test to pressure 25bar• Painting: coated internally to BS 4147 & BS
3416 Type1, Grade C• External coated to epoxy resin to 280um• Painting on any casting must not be carried
out until the casting is declared satisfactory by IIB
Factory Inspectionof Water Valves
Siam Cast Iron Plant
Factory Inspectionof Water Valves
Siam Cast Iron Plant
Factory Inspection of Polyethene PE Pipe
ISO 4427
Factory Inspection of Polyethene PE Pipe
ISO 4427
100
End of SeminarEnd of Seminar