wifi+gsm wireless security alarm system kit user manual … · 2018-04-12 · thanks for purchasing...
TRANSCRIPT
WIFI+GSM Wireless Security Alarm System KitUser Manual
Model：W20
Table of Contents
Chapter 1 Foreword
Chapter 2 Features
Chapter 3 Overview of the Host
Chapter 4 Keypad Operation
4.1 Power On
4.2 Armed the Host
4.3 Disarmed the Host
4.4 Home Armed
4.5 One-button SOS Call
4.6 Contacts Numbers
4.6.1 How to Add Contacts Numbers
4.6.2 How to Delete Contacts Numbers
4.7 Sensors Management
4.7.1 Remote
4.7.1.1 How to Add Remote
4.7.1.2 How to Delete Remote
4.7.1.3 Edit Remote Sound
4.7.2 Sensor
4.7.2.1 How to Add Sensor
4.7.2.2 How to Delete Sensor
4.7.2.3 Edit Sensor Mode
4.7.2.4 Attribute Mode Chart
4.7.3 RFID
4.7.3.1 How to Add RFID Card
4.7.3.2 How to Delete RFID Card
4.7.3.3 RFID Disarm
4.7.3.4 RFID SMS Notice
4.7.4 Wireless Siren
4.7.4.1 How to Add Wireless Siren
4.7.4.2 Overview of Wireless Siren
4.7.4.3 Add Strobe Siren into System
................................................. 1
2
5
7
8
9
10
11
.................................................
.................................................
.................................................
.................................................
.................................................
.................................................
.................................................
.................................................
.................................................
.................................................
.................................................
.................................................
.................................................
.................................................
.................................................
.................................................
.................................................
.................................................
.................................................
.................................................
.................................................
.................................................
.................................................
.................................................
.................................................
.................................................
.................................................
.................................................
.................................................
.................................................
3
5
5
5
5
6
6
6
8
8
8
9
9
10
12
12
12
13
13
13
13
13
14
Chapter 1-Foreword
Thanks for purchasing BIBENE W20 WIFI+GSM alarm system. The system uses 2.4-inch T F T color screen and touch bu�ons, embedded powerful CPU control, which it’s already paired out of box, customers can directly mount it on when they get it! This alarm system is perfect for homes, factories, schools and other places that need protec�on! Customer who wants to add up more sensors and wants to know more, please follow the instruc�on.
For more informa�on or product query, please contact us at: [email protected]
4.7.4.4 Output with Alarm
4.7.4.5 Wireless Outlet
4.7.5.1 How to Add Smart Socket
4.7.5.2 Overview of Wireless Smart Socket
4.7.5.3 Output with Alarm
4.7.5.4 Overview of Wireless Smart Socket
4.7.6 Illegal Arm
4.7.7 Tamper Alarm
4.8 Recording
4.9 Appliance
4.9.1 Outlet Timer
4.9.2 Outlet List
4.10 System
4.11 Phone
4.12 WIFI
4.13 More
4.13.1 Alarm Log(Black Box Function)
4.13.2 About Us
Chapter 5 APP Operation
5.1 Download APP
5.1.1 Register Account
5.2 APP Function Introduction
5.2.1 Setting
5.3 Add and Delete Accessories
5.3.1 Add /Delete Remote
5.3.2 Add /Delete Door/window Sensor
5.3.3 Door/window Sensor Installation
5.3.4 Add /Delete PIR Motion Sensor
5.3.5 PIR Sensor Installation
5.3.6 PIR Sensor Installation Notices
Chapter 6 Specification
Chapter 7 Troubleshooting
1
.................................................
.................................................
.................................................
.................................................
.................................................
.................................................
.................................................
.................................................
.................................................
.................................................
.................................................
.................................................
.................................................
.................................................
.................................................
.................................................
.................................................
.................................................
.................................................
.................................................
.................................................
.................................................
.................................................
.................................................
.................................................
.................................................
.................................................
.................................................
.................................................
.................................................
.................................................
.................................................
16
16
16
16
17
18
18
18
18
19
19
19
20
22
22
22
22
22
22
22
23
26
28
29
29
31
32
33
35
36
38
39
Chapter 2-Features
2.4-inch TFT color display keypad, simple menu design, easy opera�on.Support 2.4G WIFI wireless network, simple and convenient network configura�on.Support real-�me status feedback, real-�me feedback of host status to APP.Super large alarm system: Available to add 99 remotes and sensors, 20 smart sockets.Support WIFI+GSM Instant Push No�fica�on for Real-�me Alert Support RFID armed and disarmed func�on, available to add 20 cards.8 Groups of Auto Arm/ Disarm Se�ng(Can be set up by days or weeks)Support GPRS networking func�on, available to upload the host status to the network alarm system and arm or disarm the system.Equipped with 99 defense zone. Each defense zone has 8 types of defense zones to choose, each zone can be separate control. The host can be used as an ordinary mobile phone and directly dial out the phone set on the host computer.The unique black box feature displays the latest 99 arm and disarm records, 99 recent alarm records, and 99 RFID records.Built-in rechargeable high-capacity lithium ba�ery, automa�c switching to backup ba�ery when out of electricity.10 seconds message recording func�on. Available to record the message in advance, when the alarm was trigger, user can know the loca�on of the alarm.
Chapter 3-Overview of the Host
Keypad
Arm/ Page Up
Disarm/Page Down
Return Key/Keypad Lock
Enter Key/One-bu�on SOS Call
Menu Key/Delete Key
Wired Siren Entrance
Power Port
ON/OFF Bu�on
SIM Card Holder
32
Chapter 4-Keypad Opera�on
4.1 Power onInsert the SIM card into the card holder and then insert adapter into the power port. The host will emit “Welcome!” means successfully power on.
4.2 Armed the HostRemote Opera�on: Press the arming bu�on on the remote control once.Keyboard Opera�on: Click the arming bu�on on the keyboard once.
Please Note: All sensors in each defense zone will under armed status when you armed the system, if customer wants to separately control the defense zone, please control it on the keypad.
4.3 Disarmed the HostRemote Opera�on: Press the disarming bu�on on the remote control once.Keyboard Opera�on: Click the disarming bu�on on the keyboard once.
Please Note: All sensors in each defense zone will under disarmed status when you disarmed the system, if customer set up the sensor into emergency mode, the sensor will alert even the system is disarmed.
4.4 Home ArmedRemote Opera�on: Press the home arming bu�on on the remote control once.Keyboard Opera�on: Click the arming bu�on on the keyboard twice.
Icon Descrip�on Opera�on
Arm/ Page Up
Disarm/Page Down
Return Key/Keypad Lock
Enter Key/One-bu�on SOS Call
Menu Key/Delete Key
ContactsCall/SMS/RFID/CID
Sensors99 Sensors and 99 Remotes Addable
Recording10 Seconds Recording Time
ApplianceAvailable to add up 20 smart socket
System
Phone
WIFI Configura�on
MORE
Click once to arm or page up
Click once to disarm or page down
Click once to return/ Long press to lock the keypad
Click once to enter/ Long press to access emergency call
Click once to enter menu or delete
Emergency Contacts, available to set up 8 contacts, each contacts has 4 contact ways
Click to set up the sensor modes and remote and more.
Click to record the SOS record, click digit 1 to record, click 2 to play
Click to add the smart socket and set up the opera�on �me
Click to set up the delay arm or disarm �me and more
Click to dial
Click to connect WIFI
About this product
4 5
RFID Sensing Area Put your RFID card on this area to disarm the system
Please Note: Home armed func�on is ONLY works for PIR sensors, when under home armed status, PIR sensor will not alert when triggered, but door sensor will s�ll alert.
4.5 One-bu�on SOS Call
When emergency happens, press the Emergency bu�on on
the remote or long press the “√” on the keypad to ac�ve the SOS
call.
4.6 Contacts Numbers
Click the menu bu�on to enter main menu, click page up/down
bu�on to choose the Contacts icon, then click “√” enter the page.
4.6.1 How to Add Contacts Numbers
There are 8 emergency contacts available, please follow the way below to enter the numbers.
1.Click “√” to enter “Contacts”
2.Click “√” again to enter the phone call digits
3.Input the telephone numbers (Click * to enter *, long press to enter #)
4.Click “ ” to delete if enter wrong number
5.Click “ ”to choose the no�fica�on receiving choice
6.Click “ ” to determine or delete the choice
7.Click “√” again to save the phone numbers
Please Note: The factory default func�on from 1 to 6 contacts are CALL, while 7-8 is CID func�on. CID func�on CANNOT be used with other three func�ons.
4.6.2 How to Delete Contacts Numbers1.Click “√” to enter “Contacts”
2.Click “ ” or “ ” to page up or down to the number you want to delete or edit3.Click “√” again to enter ADD/EDIT func�on4.Page down to “Delete” then click “√” to delete the number5.Page down to “All Delete” you can delete all the contacts numbers
6 7
4.7 SensorsClick the menu bu�on to enter main menu, click page up/down bu�on to choose the Sensors icon, then click “√” enter the page.
4.7.1 How to Add RemoteThere are 99 remote zones, each is allows to add ONE remote. Customer can input exact digit number on the pad for quick se�ng. For example: If you wan to control 98 remote zone, click 9 and 8 on the pad, then it will go to 98 zone.
1. Click “√” to enter “Sensors” 2. Click “√” to choose “Remote”3. Click “√” again to Add/ Edit or Delete choose “Remote”4. Click “√” to enter remote adding page5. Trigger the remote by press any bu�on of it6. System will emit “Successfully Programmed”
7. Click “ ” or “ ” to set up the Sound and the Remote Sound
4.7.1.2 How to Delete RemotesDelete One Sensor. When entering Remote Control Page, page down or up bu�on to find out the Zone you want to control. Or you can input the digit on the keypad to find out the zone in a second. Then Click “√” , a window will pop out, you can delete the remote on this zone.
Delete All Sensors. When entering Remote Control Page, page down or up bu�on to go to the the bo�om of the sensors zone. “Delete All” to delete all remotes.
4.7.1.3 Edit Remote Sound
Func�on Opera�on ON/OFF Status Screen
Sound(Must Added Wireless Siren)
Panel Sound(Must Added Wireless Siren)
1. ON2. OFF
1. ON2. OFF
Wireless Siren will/will not emit an alarm when arm/disarm on the remote.
Wireless Siren will/will not emit an alarm when arm/disarm on the panel.
4.7.2 Sensor
4.7.2.1 How to Add SensorThere are 99 sensor zones, each is allows to add ONE sensor. Customer can input exact digit number on the pad for quick se�ng. For example. If you wan to control 98 zone, 9 and 8 on the pad, then it will go to 98 zone.
1. Click “√” to enter “Sensors”
2. Click“√” to choose “Sensor”
3. Click“ ” or “ ” to choose sensor zone
4. Click“√” to enter sensor adding page
5. Trigger the sensor by separate the magnet and the stripe
6. System will emit “Successfully Programmed”
7. Click “ ” or “ ” to set up the sensor sound
8 9
4.7.2.2 How to Delete SensorDelete One Sensor. When entering Sensor Control Page, click page down or up bu�on to find out the Zone you want to control. Or you can input the digit on the keypad to find out the zone in a second. Then Click “√” , a window will pop out, you can delete the sensor on this zone.
Delete All Sensors. When entering Sensor Control Page, click page down or up bu�on to go to the bo�om of the sensors zone. Click“Delete All” to delete all sensors.
4.7.2.3 Edit Sensor Mode
Function Operation ON/OFF Status
Siren
A�ribute
Event Code
Entry Delay(s)
1. ON 2. OFF
1. Instant 2. Home3. Smart 4. Emergency5. Disable 6. Doorbell7. Chime 8. Medical
1. Ambulance 2. Fire 3. Panic 4. Silent 5. Burglar 6. Perimiter7.Gas
Click to enter delay �me
Wireless Siren will/will not emit an alarm when the sensor was triggered.
Each mode will emit different alarm.(Below will elaborate each mode)
ONLY works for special alarm pla�orm. (Like CID) Will not affect normal usage.
Longest delay �me: 255 secondsONLY works for 1-10 Zones
4.7.2.4 A�ribute Mode
A�ribute
Instant
Home
Smart
Emergency
Disable
Doorbell
Chime
Medical
Descrip�on
Arm/ Home Arm: Panel send alarm no�fica�on when triggered.Disarm: Panel will not send alarm no�fica�on when triggered.
Arm/ Home Arm: No no�fica�on when PIR sensor is triggered; There is no�fica�on, when door sensor is ac�vated.
Arm/ Home Arm: When sensors are ac�vated once, panel will not send alarm no�fica�on. It will send no�fica�on at the second �me alarm is triggered (around 30s a�er the first trigger) The purpose for this property will reduce false alarm.
Panel will send alarm no�fica�on whatever system is under Arm or Disarm status.
Panel will not send alarm no�fica�on whatever system under Arm or Disarm status.
Whatever system is under Arm or Disarm status, when sensors are ac�vated, panel will goes off "Ding Dong" ring. You can treat it as doorbell for this func�on.
Panel under disarmed state: when sensors are triggered, panel will goes off "Welcome" voice;Panel under armed state: when sensors are triggered, panel will goes off ordinary alarm ring.
Panel will send alarm no�fica�on whatever system under Arm or Disarm status. It's be�er to setup this property for elder or pa�ent zone.
10 11
4.7.3 RFID
4.7.3.1 How to Add RFID CardThere are 20 RFID cards addable, each RFID zone can only add one card. RFID card can be used to disarm your system.
1. Click “√” to enter “Sensors”2. Click “√” to choose “RFID”3. Click “√” again to Add/ Edit or Delete choose “RFID”4. Click“√” to enter RFID card adding page5. Trigger the RFID card by pu�ng it on “RFID zone” on the panel6. Panel will shows “Added” when successfully added. “Configured or Need Not Add” means the card has added to other zone.
7.Click “ ” or “ ” to set up the func�on of this RFID card.
4.7.3.2 How to Delete RFID CardDelete One RFID Card. When entering RFID Control Page, click page down or up bu�on to find out the Zone you want to control. Then click “√” , a window will pop out, you can delete the RFID card on this zone.
Delete All RFID Cards. When entering RFID Control Page, page down or up bu�on to go to the the bo�om of the sensors zone. Click “Delete All” to delete all RFID Cards.
4.7.3.3 RFID DisarmRFID Disarm ON: Customer can disarm the system by using this RFID card.
4.7.3.4 RFID SMS No�ceRFID SMS No�ce ON: Customer will receive the message “01 back home” when using RFID card to disarm the system.
4.7.4 Wireless Siren 4.7.4.1 How to Add Wireless Siren(Not included)4.7.4.2 Overview of Wireless SirenJ009 wireless strobe siren is a plug &play wireless home security solu�on. Not only can work as accessory but also as standalone alarm panel.When an alarm is triggered, it will make warning sound and strobe light will flash to deter intruders. It’s suitable for wireless alarm systems,working frequency at 433MHz. (Sell separately on our store)
12 13
Set Bu�on
Switch On/Off Bu�on
Power Light
Strobe Light
Total Clear
For pairing with accessories or panel, adjust siren volume, and restore to factory se�ng.
For DC power on/ off. Plug the siren into a power outlet,siren beeps once and power light flash once, indica�ng power on successfully; Then, toggle switch bu�on to "on", keep siren in charging at the same �me
For charging status,when power light change from red to green, indica�ng full charge; Built-in ba�ery support around 8 hours standby working a�er power outage.
Strobe light will flash to deter intruders
Long press the SET bu�on and plug it into the socket, you will hear 10 beeping and flashing, release the set bu�on un�l the beeping and the flashing stop, and the light will stop.
Siren and Strobe Light:
Status
Arm
Disarm
Strobe Light
Beep Once and Flash Once
Beep Twice and Flash Twice
4.7.4.3 Add Strobe Siren into System1) Press SET bu�on on siren and hold for 3s, beep once ,LED light in siren will be on and enter into pairing mode.
2) Click “ ” to turn on the “Wireless Siren” on the panel and send signals.3) The Wireless siren will beep three �mes means successfully configured.
PLEASE NOTE: Customers are available to add limitless wireless siren into this system, but this system only has one entrance to add wireless siren and each siren CANNOT control separately, when the sensor is triggered, all sirens will alarm it also connect to the sensor siren se�ng, please check the following chart:
14 15
Wireless Siren Sensor Siren Bu�on Alarm Status
ON
OFF
ON
OFF
OFF
ON ALL Siren Alarm
Sensor Zone with Siren ON will AlarmSensor Zone with Siren OFF will NOT Alarm
NO Siren Alarm
Sensor Zone with Siren ON will AlarmSensor Zone with Siren OFF will NOT Alarm
4.7.4.4 Output with Alarm
Click “ ” to turn on the bu�on, when the system was triggered,
the wireless siren will alarm, we suggest our customer to turn it on.
4.7.5 Wireless Outlet
4.7.5.1 How to Add Smart Socket (Not included)
4.7.5.2 Overview of Wireless Smart Socket
S71 adopts interna�onal advanced digital RF technology and is
with stable performance, very stable memory and storage
capability and intelligent studying func�on, Compa�ble with
remote control of full range of protocol 1527/2262 with frequency
433,92 M H z, capable to study 60pcs remote control . (Sel l
separately on our store)
4.7.5.3 Add Smart Socket into System1) Plug the socket in and then press SET bu�on on socket and hold for 5s, LED light will TURN OFF and pairing mode.
2) Click “ ” to turn on the “Wireless Outlet” on the panel and send signals.3) The socket will flash twice means successfully added into the system.
Please Note: If you cannot add the socket into the system, please total clear the socket by press the se�ng bu�on and the plug it in, the LED light will flash from slow to fast, release the bu�on when the flash stop, and then press the bu�on for 5 seconds and enter pairing mode.
16 17
4.7.5.3 Output with Alarm
Output with Alarm
ON
OFF
Status Socket Status
Panel was armed and triggered
Smart Socket will AUTO cut off when disarmed the system for safety
Smart Socket will NOT cut off
4.7.6 Illegal Arm
Click “ ” to turn on this func�on, when it is on, customer CANNOT armed the system if one of the sensor is opened. The system will emit “01 Zone Error” to remind you to check the sensor and un�l all the sensor is correctly set up, customer can armed the system, which greatly enhance the home safety. ONLY works for an�-tamper sensor, D025 is not an� an�-tamper sensor.
4.7.7 Tamper Alarm
Click “ ” to turn on this func�on, when this func�on is on, system will send the message to inform you if the sensor is tampered. ONLY works for an�-tamper sensor, D025 is not an� an�-tamper sensor.
4.8 RecordingAvailable to record 10 seconds SOS record, when the system is intruded, it can call the reset number and play the SOS record. We recommend our customer to record their address as for emergency.
4.9 Appliance
4.9.1 Outlet ListAvailable to add 20 smart sockets, please check 4.7.5.1 How to Add Smart Socket to figure out the adding process.
Please Note: The difference between this func�on and 4.7.5 Wireless Outlet is the Wireless Outlet from Sensor part is the Main Switch while others in this part are sub-switch. If the sub-switch is on, socket will work even the main switch is turn off. Meanwhile, if the main switch is off, the socket in sub-switch will work but WILL NOT auto cut off when disarmed.
4.9.2 Outlet TimerThere are 8 groups of outlet �mers. Customer can set up auto on or off �me by days and weeks.
18 19
Time
Operate
Week
Outlet
Enter digit to enter the �me
Click “ ” to choose Auto ON/OFF
Click “ ” to choose the auto on or off day
Enter the digit to control exact socket, max input digit is 20
4.10 SystemClick page up or down or enter digit 5 on the keypad to enter system control pages.
Delay
Auto Arm/Disarm
Date& Time
Volume
Siren&Ring
GPRS
Setup the Arming delay �me and Entry delay �me, each �me are available to set up from 1-255 seconds.
Setup the the auto arm or disarm �me by days or week. 8 groups available.
Auto update to the real �me.Customer can also change it by entering the �me.
Change the Voice Volume and the Alarm Volume, available change from level 1-9.
Siren Time: Available change from 0-20 minutes. 0 means no siren when the system is triggered.GSM Ring: Available change from 0-20 �mes. GSM ring means the panel will wait for exact rings �me then pick up the phone.
Opening func�on, not available yet.
Key Tone
Screen-saver
Language
Security
Contact ID
Arm/Disarm SMS
SMS Reply
Wallpaper
Power Failure Se�ng
Restore Factory Defaults
Enter to turn on or off the key pad clicking tone.
Enter to choose the screen save �me.30s/60s/2min/5min/10min/Never
Simplify Chinese/English/German/Italian/Russian/Spanish
Set up password of the keypad or lock the keypad.Default Password: 123456 (ONLY available to set up in digits)NOTE: When locked the panel, customer should enter password before any opera�on.
Set up the CID code.Opening func�on, not available yet.
Set up to receive the SMS no�ce
Panel will reply to you phone when you using phone to control the panel.
Four Choices
Set up the no�fica�on recep�on way when the panel is on low ba�ery or power off.Voice/Siren/SMS/Call
Enter to restore the system into factory defaults
20 21
4.11 Phone Enter the phone digit on the keypad to make the phone call. (Need to work by inser�ng the SIM card.)
4.12 WIFIPlease use W20 APP to connect to WIFI.
4.13 More
4.13.1 Alarm Log(Black Box Func�on)Auto record 99 �mes Arm/Disarm history, 35 �mes of Alarm history, 12 �mes of RFID history.
4.13.2 About UsThis page shows the MAC number of the machine and other informa�on. Scan the Qr code to download our APP or search W20 on APP store.
Chapter 5-APP Opera�on
5.1 Download APPScan the QR code or search "W20" in App Store to download and install it.
Warm Tips:Tap "Allow" to allow receiving no�fica�on from "W20"
W20
5.1.1Register AccountRegister one account if you are first to use the app. Type into Email and password,then click "Confirm", register finished. You can share your login account with your family members.
22 23
IOS Android
5.1.2Wi-Fi Configura�onStep 1: Connect W20 control panel with power socket,the panel will be power on automa�cally and emit "Welcome".
Step2: Make sure that your smart phone is connected to your WIFI network.
PLEASE NOTE:W20 doesn't support WIFI of 5Ghz band. If you use dual-band (5Ghz and 2.4Ghz) router, please make sure to connect this system with the 2.4Ghz instead of the 5Ghz.
Step3: A�er account registra�on,enter into device list,click“+”to choose "W20" device, then input Wi-Fi password, click "NEXT STEP”to go to configura�on page. APP will start the 60 seconds of countdown.
Step4: Make sure your W20 has access to power in this step, and go to WIFI session on the panel, press 1 to enter WIFI configura�on process.
24 25
Step5: When 60s countdown finished, the panel will show on the “L A N U N B O U N D D E V I C E”. Then click the “L A N U N B O U N D DEVICE” to bound it into “ONLINE DEVICE”.
5.2 APP Func�on Introduc�on
Icon Descrip�on
Back to device list or user management.
Tap "Se�ng" for alarm panel se�ngs
Tap “Arm” icon, the sensors synchronized with the alarm panel will be armed.
Tap "Disarm" icon, the sensors synchronized with alarm panel will be disarmed.
Tap "Home arm" icon, the sensors synchronized with alarm panel will be home armed.
Panel ba�ery volume display.
Tap "Outlets" icon to add or delete outlets.
Tap "Contacts" icon to add or delete contacts.
Tap "Auto Switch" icon to edit auto on/off �me of the outlets
Tap “Arm Timing” icon to set up the auto Arm/Disarm �me.
Tap “Arm Delay” icon to set up the delay �me
from 0-255 seconds.
Tap “Push No�fica�on” icon to receive no�fica�on.
Tap “Alarm Time” icon to set up the alarm �me from 1 to 20 �mes.
Tap “Alarm Delay” icon to set up the alarm delay �me from 0-255 seconds.
26 27
5.2.1 Se�ng
Click “ ” for more se�ng.
Icon
Password
Device Volume
Volume
Ringer Num
Siren
Reply
SMS Reply
Descrip�on
Click to change the admin password.
Change from level 1-9
Change alarm volume from level 1-9
Set up the ring �mes from 1-20 �mes
Turn on/off the siren when system was triggered
Turn on/off the reply send to the phone
Turn on/off the SMS reply send to the phone
Lock Key
Remote Num
Sensor Num
Zone Type
Arm SMS
Arm CID
Push No�fica�on
Network Se�ngs
User Password
Push Text
Push Sound
Turn on/off to lock/unlock the panel
Add or delete remotes and set up zones.
Add or delete sensors and set up zones.
Set up the zone type of each sensor zone.
Receive the SMS when arm/disarm/home arm
Receive CID no�fica�on when arm/disarm/home arm
Tap “Push No�fica�on” icon to receive no�fica�on.
Check network status
Click to change the user password.
Edit the text content of the no�fica�on
Edit the push sound when arm/disarm/home arm
5.3 Add and Delete Accessories
5.3.1 Add /Delete RemoteImportant: Please keep panel under "Disarm" status when you add accessories.
28 29
Rc352 remote control is delicate and easy to carry. It can be a�ached to your key ring, or put into your pockets or purses. When you are about to exit or enter the house, you can use the remote control to arm or disarm the system. Or press SOS bu�on to ac�vate the alarm immediately.
Overview
2. Tap "Remotes Num" to enter adding remote page. Click “Add”, then the main panel will emit “Add 01 Zone”, then click any bu�on on the remote, the main panel will emit “Add successfully programmed”. The APP will show 1 on “Have Remote Numbers”. Click “Delete” to delete remotes. Please Note: Each Zone is ONLY AVAILABLE TO ADD UP 1 REMOTE. Customer can choose other zone to add remote.
5.3.2 Add /Delete Door/window SensorThe contact sensor contains a transmi�er and a magnet,which can be mounted on a door, window or any entry places can be opened or closed. When the transmi�er and magnet are separated, the contact sensor will send a signal to the control panel and the panel will trigger an alarm.
1. There are triangle marks on the side of the transmi�er and magnet. Make sure the triangle marks is close to each other at the first step.
30 31
2. Tap "Sensor Num" to enter adding remote page. Click “Add”, then the main panel will emit “Add 01 Zone”, then separate the magnet from transmi�er around 2cm, LED light in transmi�er will flash in Red. The main panel will emit “Add successfully programmed”. The APP will show 1 on “Have Sensor Numbers”. Click “Delete” to delete remotes.
Please Note: Each Zone is ONLY AVAILABLE TO ADD UP 1 Sensor. Customer can choose other zone to add remote.
5.3.3 Door/window Sensor Installa�on
Make sure the contact works properly before installing it. There are triangle marks on the side of the transmi�er and magnet. Make sure the triangle marks is close to each other. Once the transmi�er and magnet is separated around 2cm by intruder,the LED light in transmi�er will flash in Red. Alarm will be ac�vated.
Paste the transmi�er and magnet on doors and windows or any other open/close places with provided double-sided tapes.
5.3.4 Add /Delete PIR Mo�on Sensor
1. With intelligent processing technology, the detector can detect infrared rays released from human body, and iden�fy interfering signals and human movement signals, thus preven�ng false alarm.Being able to detect human movement within 8m space, suitable for installa�on in any place of your house that can't be cover by contact access sensor,without opening door or window.
32 33
Detec�on Lens
LED Indicator
Overview
3. Tap "Sensor Num" to enter adding remote page. Click “Add”, then the main panel will emit “Add 01 Zone”, then wave your hand before the mo�on sensor to trigger the sensor, LED light of the sensor will flash in Red. The main panel will emit “Add successfully programmed”. The APP will show 1 on “Have Sensor Numbers”. Click “Delete” to delete remotes. Please Note: Each Zone is ONLY AVAILABLE TO ADD UP 1 Sensor. Customer can choose other zone to add remote.
5.3.5 PIR Sensor Installa�onMake sure the PIR Sensor works properly before installing it.1. Choose a suitable place for installa�on.
2. Fix the PIR sensorFix the installa�on bracket on the wall with screws, then fit the groove at the back of the sensor on the bracket. You can adjust bracket angle to achieve the best detec�on effect.
34 35
3. Mount the PIR sensor in proper angle.
It's recommended to mount it at height of 2.2m from ground, and to be installed indoors in a corner as far as possible in order to obtain the ideal detec�on range. The sensi�vity is op�mal when the walk direc�on is ver�cal to the infrared direc�on. Choose the best loca�on and angle according to the actual situa�on.
5.3.6 PIR Sensor Installa�on No�ces
Please pay a�en�on on below issues when installa�on:1. Avoid infrared detectors facing to glass windows or doors;Strong light will interferes with detec�on sensi�vity. What's more, complicated situa�on such as traffic flow,stream of people also should be avoided.
2. Avoid infrared detectors facing to or close to heat/cold sources;Heat/Cold sources, such as heaters, air condi�oner, microwave oven which may cause false triggering.
36 37
3. Avoid two PIR sensors placed in the same space.There will be interference phenomenon caused by trigger at the same �me if several sensors installed in same place.
4.Avoid installing infrared detector at outside, and it's only for indoor use.
Chapter 6-Specifica�on
Input Voltage: DC 5VStandby Current: < 50ma.Alarm Current: < 450ma.Wireless Frequency: 433Mhz.GSM System: Support Gsm850/900/1800 /1900Mhz.Backup Ba�ery: 3.7 Large-Capacity Lithium Ba�ery.Alarm Loudness: 80Db(Built-In Alarm)Accessory Parameters: This alarm is equipped with EV1527 code detector. When using EV1527 code, the oscilla�on resistance is recommended to use 150k-470k.
Chapter 7-Troubleshoo�ng
Situa�on
1.No telephone call when alarm
3.Cannot read the SIM card or no phone call when alarm
4.No record when receiving the phone call
5.Remote doesn’t work
6.PIR Sensor doesn’t work
Reason Troubleshoo�ng
1. DisarmedDid not set up the contact number
1. No SIM card2. SIM card has PIN code3. Bad GSM signal4. SIM was broken5. Did not set up the call func�on6. Did not set up the SMS func�on
1.Did not set up the record
1. Failed to add into the system2. Low ba�eryWrong ba�ery installa�on or rust
1. Failed to add into the system2. Low ba�eryWrong ba�ery installa�on or rust
1. Armed the system2. Add the contact number again
1. Insert SIM card2. Cancel PIN code3. Move to open area for be�er signal4. Change a new SIM card5. Set up Call func�on6. Set up SMS func�on
1.Set up the record
1. Add it again to the system2. Change to the new ba�ery3. Clean the rust
1. Add it again to the system2. Change to the new ba�ery3. Clean the rust
38 39