The Quick Installation Guide will help you to install WU 8702-1N 150Mbps Wireless High Gain USB Adapter, including basic hardware and software installation in Windows XP, as well as configuration of wireless network availability. The Quick Installation bases on establishing an unencrypted wireless network. For detailed instructions, please refer to the User Guide on the Resource CD.

A . H a r d w a r e Instal lat ion

There are two ways to install the Adapter:

1. Plug the Adapter directly to the USB port on your computer.

2. Connect the Adapter and your computer through the USB cable attached in package.

The LED will light up when the Adapter is installed successfully and the PC is on.

B. S o f t w a r e Instal lat ion for W i n d o w s X P 1. Inserí the Resource CD into your CD-ROM drive. Double-click My Computer, and then double-click the CD/DVD drive where the installation CD was

placed. Open WU 8702-1N folder, and double-click Setup.exe. Then you will see Figurel .

Prepaiing Setup Please wait while the InstalIShield Wizard prepares (he setup.

Figure 1

2. Follow the step-by-step instructions in the continued prompted screens to complete Installation Program steps.

Note:

1) If Windows XP warns about Windows Logo testing, click Continué Anyway to continué the installation.

2) After the Installation, lili or líÜ will appear at the bottom of the screen in your system tray. Otherwise, there may be some problems about the installation, please check it seriously. ^ ^ ^ ^ ^ ^ ^

C . C o n f i g u r e w i r e l e s s c o n n e c t i o n in W i n d o w s X P with Maxnet W i r e l e s s N-Lite C l i en t Utility

The Adapter's tray icón ü ] ] shows the signal strength using color and the received signal strength indication (RSSI). If the icón is i ú ] (green), a wireless

connection has been established. If the icón is l i l i (gray), there is no connection. Follow the steps belowto launch a wireless connection manually.

1. Double-click the icón then the Maxnet Wireless N-Lite Client Utility will appear, you can also run the utility by clicking Start-» All programs -> Maxnet —> Maxnet Wireless N-Lite Client Utility —• Maxnet Wireless N-Lite Client Utility. On the prompted configuration tab page, click the Profile Management, and you will see the next screen (Figure 2).

Action &*ions Hetp

Current Status ProtoK

WDefault

Security Mode: Network Ñame 1 (SSID1): Network Ñame 2 (SSID2): Network Ñame 3 (SSID3):

• Disable WLAN ¡f LAN ¡s Conn.

Expon. I

Figure 2

2. Click Sean on the screen above, and you will see a new screen similar to Figure 3. Click Refresh, then the latest available Network will appear.

Network NaroeíSSIDl % 11* Supei XR Signa! Strength i Aufo-AP O m 5cS 13

1 2 * 13 i tpjest «3 m 13 dB 11 í CUBY «3 >S | é 20 dt 11 f Maxnet «*3 27 m

o 3 mm i m&mm 1 «¡3 its &

i Wireless é

11 «i

Figure 3

1

3. In the screen above, highlight a network ñame (take test for example) and click Actívate, then you will see the next screen (shown in Figure 4). Enter the Profile Ñame, click OK and you can connect to the network.

General Secunty Advanced

Profüe Ñame

Figure 4

Note: If a well-balanced wireless network cannot be created, please refer to the User Guide on the Resource CD or your dealer for help.

D. C o n f i g u r e w i r e l e s s c o n n e c t i o n in W i n d o w s X P with W i n d o w s X P W i r e l e s s Z e r o C o n f i g u r a t i o n

1. To use Windows XP Wireless Zero Configuration, select Option-*Select Client Software... on the menú of Utility shown in Figure 5.

Neíwork Type SecurtyMode Neiwo* Namel (SSID1J Neftwrk Name2(SSID2t

Figure 5

2. After that, you will see Figure 6. Select Windows option and click OK. Wait a minute until the screen prompt that Client Software selection.. S U C C E S S F U L H and Click OK

Select Client Software

Select the software application to control your wireless device

0 Windows

O Maxnet Wireless N-Lite Client Utiliti>

O Third-Party Tool

f " ~ O * - I [ Cancel j

Figure 6 3. Right-click the icón ", and then select View Available Wireless Networks in the next screen (Figure 7).

Disable Status

View Available Wireless Networks

Change Windows Firewall settings

Open Network Connections I Figure 7

4. Then, Figure 8 will appear with many available wireless network choices. You can highlight a network (take test for example) and then click Connect to add to a network.

Note: If you have not installed SP2 for Windows XP, the screens below will not be available.

rrr_ '

I,

•

Figure 8

5. If the connection is finished, the icón will display like the next screen shown.

2

I Wireless Network Connection (test) Speed: iSOMbps Signal Strength; Excellent Status: Connected

Figure 9

Note: If a well-balanced wireless network cannot be created. please refer to the User Guide on the Resource CD or your dealer for help.

E . C o n f i g u r e w i r e l e s s c o n n e c t i o n in W i n d o w s V i s t a

1. Inserí the Resource CD into your CD-ROM drive. Double-click My Computer, and then double-click the CD/DVD drive where the installation CD ws placed. Open WU 8702-1N folder, and double-click Setup.exe. Then you will see Figure 10.

Figure 10

2. Follow the step-by-step instructions in the continued prompted screens to complete Installation program steps.

3. Right-click the i c o n S in your system tray, then click "Connect to a network".

•^^^^^^•^ §mfm Connect to a network

Turrt on artivíty anímatien

Turn cff notífication of new networfcs

Disgncse and repaír

Figure 11

4. The following screen (shown in Figure 12) will show you available wireless networks. Highlight or right click the one you want to join in, and then clic Connect.

Figure 12

5. To continué, click Connect Anyway. To end the connection, click Cancel.

6. If the connection is successfully established, the following screen will appear. Click Cióse to finish the connection.

Figure 13

Note: For more information about Windows Vista WLAN Autoconfig on a Windows Vista computer, refer to Help and Support of the Operating System.

3

F. W P S conf igura t ion

WPS (Wi-Fi Protected Setup) function allows the Adapter to join a wireless network quickly.

If the wireless card supports Wi-Fi Protected Setup (WPS), you can establish a wireless connection between wireless card and router using either Push Button Configuration (PBC) method or PIN method.

First, the WPS software should be installed. Inserí the Resource CD inío your CD-ROM drive. Double-click My Computer, and íhen double-click íhe CD/DVD drive where íhe installation CD was placed. Open WU 8702-1N folder, and double-click WPS.exe. Then you will see Figure 14.

WPS Installation Program InstallShield Wizaid

Preparing Setup Please wait whüe the InstatSNetd WÍ2ard prepares the setup.

wepating the InstallShield Wéard, w :

Figure 14

Please follow íhe clue of íhe coníinued screens ío compleíe íhe WPS installation. After íhal, WPS funcíion can be enabled. Here we will iníroduce íwo ways ío configure íhe WPS (For íhe configuraíion of WPS, here lakes íhe Wireless Rouíer of our company for example. For more ways of WPS configuralion, please refer ío íhe User Guide inside íhe CD aííached in package).

1. P B C (Push Button Configuration)

1) Press íhe WPS bulíon on íhe froní panel of íhe Rouíer.

W P 8

O Figure 15

2) Press and hold íhe WPS button on the adapter for 2 or 3 seconds.

3) Then wait a minute uníil Figure 16 appears. Click Finish lo compleíe íhe WPS configuration.

Wifeiess Confiquratton Compíeted Your computer has successfuih/ ¡oined the Maxnet 1 n

Figure 16 2. PIN method

1) Double click the icón on the deskíop ío open íhe WPS Utility and you will see Figure 17. Click Next to coníinue.

Welcome to WPS

Figure 17

4

2) Then Figure 18 will appear. Select the third option and enter the PIN valué which is labeled on the bottom of the Router. Click Next.

Join a Wireless Network

WPS is preparing to join your computer to

Which setup method do you want to use?

t * - — i Push the button on my access point

WPS Enter a PIN into my access point or a registrar •

Ente; the PIN from your access point below and click Next to contin

Access Point PIN: 12345670

Automática ) select the network 0

Figure 18

3) When Figure 16 appears, the WPS configuration is complete.

Note: If you genérate a new PIN code for your router, please enter the new one instead.

COPYRIGHT & TRADEMARKS

Specifications are subject to change without notice. Other brands and product ñames are trademarks or registered trademarks of their respective holders.

No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from MAXNET.

© 2 0 0 9 - 2 0 1 0 Maxnet

All rights reserved.

ht tp: / /www.maxnet .pe

This equipment may be operated in all EU countries (and other countries following the EU directive 1999/5/EC). Usage in the following countries might be subject to restrictions: FR, IT, NO. See detail information in product's document of resource CD.

5

7109503926