Extended abstracts of IWEC2019The 8th International Workshop of Energy Conversion

August 22-26, 2019, Jiangsu, China

Type the Title of your Paper Here in 12 pt (Initial Capital)

A. Li,* and A. WangDepartment of Mechanical Engineering, China University, Beijing, China

*corresponding author, E-mail: ******@beijing.ac.cn

T. YamadaDepartment of Mechanical Engineering, Japan University, Tokyo, Japan

ABSTRACTThis article describes the preparation procedure of the final camera-ready manuscript of the paper that was invited

and/or accepted for IWEC2019. When authors submit their work to IWEC2019 for publishing, they should strictly follow these instructions in order to maintain high standards of the extended abstracts. The aim of the style file “template (iwec2019).doc” is to allow authors of papers to prepare the final camera-ready manuscript with MS-WORD easily. This document is a MS-Word template which defines the required format. MS-Word file of this document is available on the conference website: https://iwec2019.doshisha.ac.jp/index.html

The total pages of a full paper should not be over 2 pages. Each paper size should be A4 (21.0cm×29.7cm) and the following margins should be set:

Left 12.7 mm Right 12.7 mmTop 12.7 mm Bottom 25.4 mm

First part (title and authors’ information): The first part includes the paper title, authors’ name and affiliation. The font of the title must be Helvetica and the font size is bold 12pt. The font of the Authors’ name and affiliation must be Times New Roman and the font size are bold 10.5pt and 10pt, respectively.Second part (abstract): The second part consisting of the abstract and paper body must be edited in the double column format. The level-two heading starts from the left in Times italic underlined 10.5pt font. The main text uses Times 10pt font with single spacing. New paragraphs indent 6.3mm on the first line.

Figures and tables: All figures and tables should be placed after their first mention in the text. Large figures and tables may span across both columns. Scanned images (e.g., line art, photos) can be used if the output resolution is at least 600 dpi. Figures should be top of the pages and figure captions should be below the figures. Tables should be bottom of the pages and table captions should be above the tables. They should be referred to in the text as, for example, Fig. 1, or Figs. 1~3. In the paper, all authors are required to use the SI unit.

Equations: Equation numbers should be Arabic numerals enclosed in parentheses on the right-hand margin. They should be cited in the text as, for example, Eq. (1), or Eqs. (1) ~ (3). Equations start from the left on the column. Punctuate equations with commas or periods when they are part of a sentence. For example,

(1)

(2)

where x is the state vector.

Table 1 The caption should be placed before the table.

A B C

I 150 % 16.3 % 18.2 %

II 31.1 % 33.8 % 29.8 %

III 13.3 % 12.1 % 11.1 %

References: References should appear in a separate bibliography at the end of the paper, with items referred to by numerals in square brackets [1, 4-5]. Times New Roman 10pt is used for references [5]. References should be complete in IWEC2019 style shown in the Reference section of this article.

ACKNOWLEDGMENTSThis style file was provided by IWEC2019

REFERENCES[1] Kim, J. and Lee, K.D., 1991, “Structure of …,” AIAA J., Vol.29-11, p.221.[2] Kays, W.M and Crawford, M.E., 1990, Heat transfer, Wiley, New York, pp.256-258.[3] Ray, M.M., 1991, “Direct Simulation of …,” Proc. 41SCFD-Davis, Vol.2, pp.13-23.[4] Degrez, G., 1992, Implicit Time-Dependent…, in Computational Fluid Dynamics, Wendt, J.F. (Ed.), CRC Press, Tokyo, pp.18-26.

Fig. 1 The caption should be placed after the figure.Fig. 1 The caption should be placed after the figure.