waters ipad app target placement instructions ipad ap… · please note that incorrect positioning...
TRANSCRIPT
©2014 Waters Corporation 1
Waters iPad App Target Placement instructions
The documents provides guidance on where the targets should be place on the SYNAPT G2-Si, Xevo G2-s QTof and Xevo TQ-S when using the virtual demo function of the app.
©2014 Waters Corporation 2
Waters iPad App Set Up
SYNAPT G2-Si
Position 1: marker number 4
Position 4:
marker number 3
Position 5:
Marker
Number 2
Position 2 :marker number 0
Position 3:marker number 1
4 0
3 2
1
Each of the 5 markers for the SYNAPT G2-Si virtual demo are numbered. Please position each numbered marker as illustrated below. Please note that incorrect positioning will result in poor performance of the virtual demo aspect of the app. Close-up views of each of how each marker should be positioned are on the next two slides.
©2014 Waters Corporation 3
Position 1: marker number 4
Align Target with grip edge and top of door
moulding
Position 2 :marker number 0
Top corner of front RHS panel
Position 3:marker number 1
Top rear corner of top tight
hand side panel
Waters iPad App Set Up
SYNAPT G2-Si
©2014 Waters Corporation 4
Position 4: marker number 3 Position 5 :marker number 2
TriWave
TriWave
Waters iPad App Set Up
SYNAPT G2-Si
©2014 Waters Corporation 5
Waters iPad App Set Up
Xevo G2-S QTof
Position 1: marker number 2
Position 6:marker number 0
Position 5:marker number 1
2
2
1
Position 2: marker number 4
Position 1: marker number 2
4
5
Position 4:marker number 3
4
4 4
Each of the 6 markers for the Xevo G2-S QTof virtual demo are numbered. Please position each numbered marker as illustrated below. Please note that incorrect positioning will result in poor performance of the virtual demo aspect of the app. Close-up views of each of how each marker should be positioned are on the next two slides.
©2014 Waters Corporation 6
Position 1: marker number 2
Fit top edge under radius and
along right hand side.
Position 2 :marker number 4
Fit in corner of panel split on
tower
Position 3:marker number 5
Fit to below grey top in corner
of blue panel
Waters iPad App Set Up
Xevo G2-S QTof
©2014 Waters Corporation 7
Position 4: marker number 3
Align edge with screw head and
top on panel crease
Position 5 :marker number 1
Align with screw heads
Position 6 :marker number 0
Align edge with screw head
and top on panel crease
Waters iPad App Set Up
Xevo G2-S QTof
©2014 Waters Corporation 8
Position 1: marker number 3
Position 4:
Marker
Number 2
Position 2 :marker number 0
Position 3:marker number 1
3
2
1
Waters iPad App Set Up
Xevo TQ-S
Each of the 4 markers for the Xevo TQ-S virtual demo are numbered. Please position each numbered marker as illustrated below. Please note that incorrect positioning will result in poor performance of the virtual demo aspect of the app. Close-up views of each of how each marker should be positioned are on the next two slides.
©2014 Waters Corporation 9
Position 1: marker number 3
Align with corner of Door panel: top edge of target
to bottom edge of radius
Position 2 :marker number 0
Align edge of Target with top edge of side panel and
fixing screw.
Position 3:marker number 1
Align Target to top edge and corner of panel
Waters iPad App Set Up
Xevo TQ-S
©2014 Waters Corporation 10
Position 4: marker number 2
Align Target to bottom corner of panel
Waters iPad App Set Up
Xevo TQ-S