specificationtoroson.com/uploads/product/5b6ced13ccfb8.pdf · vsn enables the test image generation...
TRANSCRIPT
SPECIFICATIONTFT-LCD Module
VIETE (HONG KONG) GROUP LIMITED
Customer:
Model Name:
SPEC NO.:
Date:
Version:
Preliminary Specification
Final Specification
Approved by Reviewed by Prepared by
For Customer’s Acceptance
Approved by Comment
The copyright belongs to Viete.Any unauthorized use is prohibited.
VJ070IN1K
Page 1/25
陈日升
Viete Group copyright 2018All right reserved,Copying forbidden.
Record of Revision
The copyright belongs to Viete.Any unauthorized use is prohibited.
Version Page ContentRevise Date
VIETE (HONG KONG) GROUP LIMITED
Page 2/25
The copyright belongs to Viete.Any unauthorized use is prohibited.
VIETE (HONG KONG) GROUP LIMITED
Page 3/25
Contents
1. GENERAL SPECIFICATIONS ................................................................................................. 4
7. MECHANICAL DRAWING .......................................................................................................24
2. PIN ASSIGNMENT ....................................................................................................................5- 6
3. ELECTRICAL SPECIFICATIONS ........................................................................................... 7
3.1. ABSOLUTE MAXIMUM RATINGS ................................................................................... 7
3.2. TYPICAL OPERATION CONDITIONS ........................................................................................ 7-8
3.3. Power Sequence ................................................................................................................. 9
3.5. DISPLAY TIMING (VIDEO MODE) ......................................................................................... 14-17
4. OPTICAL CHARACTERISTICS ............................................................................................ 18-21
5. RELIABILITY TEST ITEMS ................................................................................................... 22
6. HANDLING PRECAUTIONS ................................................................................................. 23
8. PACKAGE SPECIFICATION ................................................................................................. 25
3.4. COMMAND SEQUENCE .........................................................................................................10-13
SPEC NO.:
No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
Item Specification Remark
LCD size
Driver element
Resolution
Display mode
Dot pitch
Active area
Module size
Surface treatment
Color arrangement
View direction(Gray Inversion)
Interface
Panel power consumption
Backlight power consumption
Weight
7.02 inch(Diagonal)
LTPS TFT active matrix
1200X3(RGB)X1920
Normally Black
0.0785(W)x0.0785(H) mm
94.5(W)x151.2(H) mm
Hard Coating
RGB-stripe
Free
MIPI
0.14W (Typ.) ,0.17(max )
4.83W (Typ.)
TBD
165.55(W)x111.33(H)x2.38(D)mm Note 1
Note 1: Refer to Mechanical Drawing.
The copyright belongs to Viete.Any unauthorized use is prohibited.
1.General Specifications
Date: 2018/05/04
VIETE (HONG KONG) GROUP LIMITED
VJ070IN1K
This model is a color active matrix TFT LCD that uses Low-temperature poly-silicon TFT as a switching device. It is composed of a TFT LCD cell, IC and FPC. And it has a 7.02 (10:16) inch diagonally measured active display area with WUXGA (1200 horizontal by 1920 vertical pixel) resolution.
Page 4/25
2.Pin Assignment
Pin No.
1 NC
IOVCC
IOVCC
2
3
4
5
GND
GND
GND
GND
GND
GND
GND
GND
6 NC
HS
VS
NC/TE
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
Symbol Description Remark
No connection
Power supply for system ,IOVCC=1.8V
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
No Connection
Horizontal scan Signal for touch
Vertical scan Signal for touch
Tearing effect output signal for NVM(OTP),Let it open when not in use
A 40pin connector is used for the module electronics interface.In this model used “F62240-H1210B” manufactured by Vigorconn Technology.
The copyright belongs to Viete.Any unauthorized use is prohibited.
SPEC NO.: Date: 2018/05/04
VIETE (HONG KONG) GROUP LIMITED
RST Device reset signal
MIPI_1N
MIPI_1N
MIPI_2N
MIPI_3N
MIPI_CKN
MIPI_1P
MIPI_1P
MIPI_2P
MIPI_3P
MIPI_CKP
MIPI Negative data signal (-)
MIPI Negative data signal (-)
MIPI Negative data signal (-)
MIPI Negative data signal (-)
MIPI Negative data signal (-)
MIPI Negative data signal (+)
MIPI Negative data signal (+)
MIPI Negative data signal (+)
MIPI Negative data signal (+)
MIPI Negative data signal (+)
VJ070IN1K
Page 5/25
27
28
29
30
31
32
33
34
35
36
37
38
39
40
The copyright belongs to Viete.Any unauthorized use is prohibited.
SPEC NO.: Date: 2018/05/04
VIETE (HONG KONG) GROUP LIMITED
PWMO PWM control signal for LED driver (CABC)
NC/BIST
NC
NC
VSP
VSN
Enables the Test Image Generation function, if not used, connect to ground
No Connection
NC
GND Ground
LED-
LED-LED cathode
No connection
VSNAnalog supply negative voltage
VSPAnalog supply positive voltage
LED+
LED+LED anode
VJ070IN1K
No connection
Note: Definition of scanning direction. Refer to the figure as below:
Top
RightLeft
Down
Page 6/25
3. Electrical Specifications3.1. Absolute Maximum Ratings
SPEC NO.: Date: 2018/05/04
VIETE (HONG KONG) GROUP LIMITED
3.2. 1. DC Characteristics
Item SymbolValues
Min. Max.Unit Remark
( Note 1)
Power voltage
V
V
V
0
0
-6.5
4.6
6.5
0
IOVCC
VSP
VSN
Note 1: The absolute maximum rating values of his product are not allowed to be exceededat any times. Should a module be used with any of the absolute maximum ratings exceeded, the characteristics of the module may not be recovered, or in an extreme case the module may be permanently destroyedTherefore, when designing a system incorporating the module, make sure that adequate attentions be paid to the variations in the supply voltages, the characteristics of parts that are connected, surges in the input and output lines, and the ambient temperatures. .
The copyright belongs to Viete.Any unauthorized use is prohibited.
Operation Temperature
Storage Temperature
-10
-30
Top
Tst
℃
℃
60
70
VJ070IN1K
3.2. Typical Operation Conditions
item symbol min type max unit Remark
Power suply voltage forAnalog
Power suply voltage for Logic
Input signal voltage for (RES)
Output signal voltage for (TE)
Input signal voltage (DSI)
VSP
VSN
IOVCC
VIL
VIH
VOL
VOH
Low level
High level
Input voltage
Differential input low threshold
Differential input high threshold
VIL(DSI)
VIH(DSI)
VIDTL
VIDTH
VCMRX
5.3 5.5 5.7
-5.7 -5.5 -5.3
V
V
V
V
V
V
1.7 1.8 1.9
0 – 0.3*IOVCC
0.8*IOVCC
– IOVCC
0 – 0.2*IOVCC
–
-550
880 1350
70 330
-70
70
mV
mV
Low power receiver
High speed receiver
TE
XRES
VIOVCC
-50 –
–
–
–
–
0.7*IOVCC
–
–
Page 7/25
Item SymbolValues
Min. Max.Unit Remark
Typ.
Current for Driver
IOVCC
VSP
VSN
-
-
-
12
10
10
24
13
13
mA
mA
mA
The copyright belongs to Viete.Any unauthorized use is prohibited.
(GND=AVSS=0V)
Item SymbolValues
Min. Max.Unit Remark
Typ.
3.2.3. Backlight Driving Conditions
3.2.4. Backlight Absolute Maximun Ratings
Voltage for LED backlight
Current for LED backlight
LED life time
VL
IL
- 20,000
480
-
10.2
-
420
8.4 V
mA
Hr
Note 1
Note 2
Note 1:
Note 2:
℃ and The LED Supply Voltage is defined by the number of LED at Ta=25 IL=480mA
The “LED life time” is defined as the module brightness decrease to 50% original brightness at Ta=25 ℃a nd IL=500mA.The LED lifetime could be decreased if operating IL is lager than 500mA.
Item Symbol Condition Rating Unit
Forward Current
Peak Forward Current
Power Description
IFM
IFPDuty:1/10 pulseWidth 0.1ms
Pd
300 mA
mA570
4400 mW
VIETE (HONG KONG) GROUP LIMITED SPEC NO.:VJ070IN1K Date: 2018/05/04
3.2.2. Current Consumption
White pattren
9.3
500
Page 8/25
The copyright belongs to Viete.Any unauthorized use is prohibited.
ItemValues
Min. Typ. Max.Unit symbol
ms
ms
ms
ms
IOVCC on toVSP on time -
-
VIETE (HONG KONG) GROUP LIMITED SPEC NO.:VJ070IN1K Date: 2018/05/04
3.3. Power Sequence
VSPon toVSN on time
VSN on toREST on time
VSN off toVSP off time
VSP off toIOVCC off time
tsVSP
tPON1
tRW1
tPOFF1
thVSP ms
-
-
-
-
-
-
-
-
1
1
0
0
0
Page 9/25
The copyright belongs to Viete.Any unauthorized use is prohibited.
SPEC NO.: Date: 2018/05/04
VIETE (HONG KONG) GROUP LIMITED
VJ070IN1K
3.4. Command sequence3.4.1 Status Flow (1200RGBx1920, R69429, MIPI 4lane)
3.4.2 Sequence(A) Power on
sequence DataType index
parameters description comment
(hex) (hex) # (hex)
POWER OFF STATE
PWR supply on IOVCC on DSI input should be at GND level while IOVCC off
wait 5ms
PWR supply on VSP,VSN on
wait 20ms
RESET L->H RESET L->H
wait 10ms
PWR supply off VSP,VSN off
(*1)Can skip "VSP/VSN off" in case of going to normal mode without staying sleep status.
(wait 20ms)
SLEEP MODE
Page 10/25
The copyright belongs to Viete.Any unauthorized use is prohibited.
SPEC NO.: Date: 2018/05/04
VIETE (HONG KONG) GROUP LIMITED
VJ070IN1K
(B) On sequence
sequence DataType index
parameters description comment
(hex) (hex) # (hex)
SLEEP MODE
PWR supply on VSP,VSN on
wait 20ms
command 05 01 - - soft reset
wait 10ms
command 23 B0 1 00 MCAP
command 29 B3
1 14
Interface setting
2 08
3 00
4 22
5 00
command 29 B4 1 0C Interface ID setting
command 29 B6
13A
DSI control
2 D3
command 15 51 1 E6- write display brightness
command 15 53 1 2C write control display
command 05 29 - - set display on
wait 10ms
command 05 11 - - exit sleep mode
Wait 120ms
NORMAL MODE
Page 11/25
The copyright belongs to Viete.Any unauthorized use is prohibited.
SPEC NO.: Date: 2018/05/04
VIETE (HONG KONG) GROUP LIMITED
VJ070IN1K
(C) Off sequence
sequence DataType index parameters description comment
(hex) (hex) # (hex)
NORMAL MODE
command 05 28 - - set display off
wait 20ms
command 05 10 - - enter sleep mode
wait 80ms
stop HS transmission
PWR supply off VSP,VSN off
wait 20ms
SLEEP MODE
(D) Power off
sequence DataType index
parameters description comment
(hex) (hex) # (hex)
SLEEP MODE
RESET H->L
PWR supply off IOVCC off DSI data/clk should be at GND level after IOVCC off.
POWER OFF STATE
Page 12/25
The copyright belongs to Viete.Any unauthorized use is prohibited.
SPEC NO.: Date: 2018/05/04
VIETE (HONG KONG) GROUP LIMITED
VJ070IN1K
(E) Enter DSTB
sequence DataType index parameters description comment
(hex) (hex) # (hex)
SLEEP MODE
command 23 B0 1 00 MCAP
command 23 B1 1 01 DSTB=1
DSTB MODE
(F) Exit DSTB
sequence DataType index
parameters description comment
(hex) (hex) # (hex)
DSTB MODE
RESET H -> L
wait 10ms
PWR supply on VSP,VSN on
wait 20ms
RESET L->H RESET L->H
wait 10ms
PWR supply off VSP,VSN off
(*1)Can skip "VSP/VSN off" in case of going to normal mode without staying sleep status.
(wait 20ms)
SLEEP MODE
Page 13/25
The copyright belongs to Viete.Any unauthorized use is prohibited.
Date: 2018/05/04
VIETE (HONG KONG) GROUP LIMITED
SPEC NO.:VJ070IN1K
3.5. Display Timing (Video Mode)
Page 14/25
The copyright belongs to Viete.Any unauthorized use is prohibited.
SPEC NO.: Date: 2018/05/04
VIETE (HONG KONG) GROUP LIMITED
VJ070IN1K
Vertical Display Timing
Horizontal Display Timing
Page 15/25
The copyright belongs to Viete.Any unauthorized use is prohibited.
SPEC NO.: Date: 2018/05/04
VIETE (HONG KONG) GROUP LIMITED
VJ070IN1K
Page 16/25
The copyright belongs to Viete.Any unauthorized use is prohibited.
SPEC NO.: Date: 2018/05/04
VIETE (HONG KONG) GROUP LIMITED
VJ070IN1K
Page 17/25
The copyright belongs to Viete.Any unauthorized use is prohibited.
SPEC NO.: Date: 2018/05/04
VIETE (HONG KONG) GROUP LIMITED
VJ070IN1K
4. OPTICAL CHARACTERISTICS(Ta=+25℃)
Item Symbol Condition
Values
Unit Remar
k Min. Typ. Max.
Viewing angle (CR≥ 10)
θL Φ=180°(9 o’clock) - 80 -
degree Note 1 Note 5
θR Φ=0°(3 o’clock) - 80 -
θT Φ=90°(12 o’clock) - 80 -
θB Φ=270°(6 o’clock) - 80 -
Response time TON+ TOFF
Normal θ=Φ=0°
25 msec Note 2 Note 3
Contrast ratio CR 1200 - - Note 4 Note 5
Color chromaticity
WX 0.28 0.31 0.34 -
Note 5
WY 0.29 0.33 0.35 -
Transmittance Tr - - 3.8 - % Note 5
NTSC Ratio 71.5 % Note 5
Test Conditions:
VCC=1.8V, the ambient temperature is 25℃.
The test systems refer to Note 2.
1000900Luminance L cd/㎡ Note 6
Page 18/25
The copyright belongs to Viete.Any unauthorized use is prohibited.
Date: 2018/05/04
VIETE (HONG KONG) GROUP LIMITED
SPEC NO.:VJ070IN1K
Note 1: Definition of viewing angle range
Fig. 4-1 Definition of viewing angle
Note 2: Definition of optical measurement system. The optical characteristics should be measured in dark room. After 30 minutes operation, the optical properties are measured at the center point of the LCD screen. (Viewing angle is measured by ELDIM-EZ contrast/Height :1.2mm, Response time is measured by Photo detector TOPCON BM-7, other items are measured by BM-5A/ Field of view: 1° /Height: 500mm.)
Normal line θ=Φ=0°
Normal line θ=Φ=0°
Photo detector
Φ=90° 12 o’clock direction
Φ=270° 6 o’clock direction
Φ=0°
Φ=180°
Active Area
500mm
LCD Panel
Φ=90° 12 o’clock direction
Φ=270° 6 o’clock direction
Φ=0° Φ=180°
Active Area
θL
θT
θB
θR
Page 19/25
The copyright belongs to Viete.Any unauthorized use is prohibited.
SPEC NO.: Date: 2018/05/04
VIETE (HONG KONG) GROUP LIMITED
VJ070IN1K
Fig. 4-2 Optical measurement system setup
Note 3: Definition of Response time The response time is defined as the LCD optical switching time interval between “White” state and “Black” state. Rise time (TON) is the time between photo detector output intensity changed from 90% to 10%. And fall time (TOFF) is the time between photo detector output intensity changed from 10% to 90%.
Fig. 4-3 Definition of response time
Note 4: Definition of contrast ratio
Luminance measured w hen LCD on the "Black" state
Luminance measured w hen LCD on the " White" stateContrast ratio (CR)
Note 5: Definition of backlight The data is measured by using VIETE's backlight system.
100%
90%
10% 0%
Ph
oto
de
tecto
r outp
ut
(Re
lative
va
lue
)
TONTOFF
White (TFT OFF) Black (TFT ON) White (TFT OFF)
Page 20/25
The copyright belongs to Viete.Any unauthorized use is prohibited.
SPEC NO.: Date: 2018/05/04
VIETE (HONG KONG) GROUP LIMITED
VJ070IN1K
Note 6:Definition of Luminance Uniformity
Active area is divided into 9 measuring areas (Refer to Fig. 4-4 ).Every measuring point is placed at the center of each measuring area.
Luminance Uniformity(Yu)=Bmin
Bmax
L-------Active area length W----- Active area width
L
L/6 L/3L/3
W
W/3
W/3
W/6
Page 21/25
Fig. 4-4 Definition of test point
The copyright belongs to Viete.Any unauthorized use is prohibited.
SPEC NO.: Date: 2018/05/04
VIETE (HONG KONG) GROUP LIMITED
VJ070IN1K
5. Reliability Test Items
High Temperature Storage
Ta = 70℃ 240hrs Note 1,Note 4
Low Temperature Storage
Ta = -30℃ 240hrs Note 1,Note 4
High Temperature Operation
Ts = 60℃ 240hrs Note 2,Note 4
Low Temperature Operation
Ta = -10℃ 240hrs Note 1,Note 4
Operate at High Temperature and Humidity
Ta=40℃ H=95%RH 240hrs Note 4
Thermal Shock -30℃/30 min ~ +70℃/30 min for a total 50cycles, Start with cold temperature andend with high temperature.
Note 4
Package Vibration Test Random vibration 0.015 G2/Hz fram 5~200Hz -6dB/octave from 200~500Hz 2hours every X,Y,Z, total 6 hours
Package Drop Test
Drop a full transportation package from a height : 72 cm(Weight<=10Kg); 60 cm(Weight>10Kg); 1 corner, 3 edges, 6faces.
Note 1: Ta is the ambient temperature of samples. Note 2: Ts is the temperature of panel’s surface. Note 3: In the standard condition, there shall be no practical problem that may affect the display function. After the reliability test, the product only guarantees operation, but don’t guarantee all of the cosmetic specification. Note 4: Before cosmetic and function test, the product must have enough recovery time, at least 2 hours at room temperature.
Page 22/25
The copyright belongs to Viete.Any unauthorized use is prohibited.
SPEC NO.: Date: 2018/05/04
VIETE (HONG KONG) GROUP LIMITED
VJ070IN1K
liquid crystal touches your skin or clothes, wash it off immediately using soap and water.
b. Handlingi. The LCD and touch panel is made of plate glass. DO NOT subject the panel to
mechanical shock or to excessive force on its surface.ii. Do not handle the product by holding the flexible pattern portion in order to
assure the reliabilityiii. Transparency is an important factor for the touch panel. Please wear clear finger
sacks, gloves and mask to protect the touch panel from finger print or stain andalso hold the portion outside the view area when handling the touch panel.
iv. Provide a space so that the panel does not come into contact with othercomponents.
v. To protect the product from external force, put a covering lens (acrylic board orsimilar board) and keep an appropriate gap between them.
vi. Transparent electrodes may be disconnected if the panel is used underenvironmental conditions where dew condensation occurs.
vii. Property of semiconductor devices may be affected when they are exposed tolight, possibly resulting in IC malfunctions.
viii. To prevent such IC malfunctions, your design and mounting layout shall be donein the way that the IC is not exposed to light in actual use.
ix. c. Static Electricity
i. Ground soldering iron tips, tools and testers when they are in operation.ii. Ground your body when handling the products.iii. Power on the LCD module BEFORE applying the voltage to the input terminals.iv. DO NOT apply voltage which exceeds the absolute maximum rating.v. Store the products in an anti-electrostatic bag or container.vi.
d. Storage
i. Store the products in a dark place at +25℃±10℃ with low humidity (65%RH orless).
ii. DO NOT store the products in an atmosphere containing organic solvents orcorrosive gas.
iii. e. Cleaning
i. DO NOT wipe the touch panel with dry cloth, as it may cause scratch.ii. Wipe off the stain on the product by using soft cloth moistened with ethanol. DO
Not allow ethanol to get in between the upper film and the bottom glass. It maycause peeling issue or defective operation. Do not use any organic solvent ordetergent other than ethanol.
Page 23/25
6. Handling Precautionsa. SafetyThe liquid crystal in the LCD is poisonous. DO NOT put it in your mouth. If the
SPEC NO.:
The copyright belongs to Viete.Any unauthorized use is prohibited.
7 MECHANICAL DRAWING.MDate: 2018/05/04
VIETE (HONG KONG) GROUP LIMITED
VJ070IN1K
*96.3
±0.1
5U
P B
EZ
EL O
PE
N
96.9
Top P
OL
155.25POL
94.5
LC
D A
A
151.2LCD AA (0.5)
*153.1±0.15UP BEZEL OPEN 6.37
*111.33
±0.1
5
165.55±0.2
2.38
±0.1
4.8
0.6
备注
要求
:
1.搭配
玻璃
类型
: JDI TP0702002N;
2.成品
色度
:X=0.31±
0.03;Y=0.33±0.03;
3.模组
亮度
要求
:1000cd/m2 (
TYP);
4.背光
电性
要求
:IF=480mA(TYP);VF=8.4-10.2V;
5.背光
均匀
性:
9 point>80%;
6.符合
RoHS标准
;
7.未注
尺寸
公差
:±0.2;
MARK
DESCRITU
ON:
SHEET:
DRAWING
PROJE
CTIONAPPROVED
BY:
CHECKED BY:
DESIGN BY:
Unspecified
Tolerance:
UNITS:
mm
DATE
:PAR
T NU
MBER
:
DO NOT
SCALE
THIS
DRAWING.MODE
L
1 Of
1
REVISERREV.
DESCRIPTIONDATE
±0.2
L>1
00
L≦35
边长
度L
35<L≦100
平面
翘曲
度公
差
≦0
.3m
m
≦L
*0
.3%
mm
≦
0.
1m
m
对应
公差
范围
(51.8
8)
VJ070IN1K 厦
门韦
达光
电有
限公
司
VIE
TE
TE
CH
NO
LO
GY
Co
.,Ltd
Page 24/25
The copyright belongs to Viete.Any unauthorized use is prohibited.
SPEC NO.: Date: 2018/05/04
VIETE (HONG KONG) GROUP LIMITED
VJ070IN1K
8. Package Specification
TBD
Page 25/25