vikram thakur 803043
TRANSCRIPT
-
7/31/2019 Vikram Thakur 803043
1/23
SEMINARINDUSTRIAL TRAINING
By Vikram Thakur
ECE 7th Sem
803043
-
7/31/2019 Vikram Thakur 803043
2/23
-
7/31/2019 Vikram Thakur 803043
3/23
BSNL Provides the Services as:
-
7/31/2019 Vikram Thakur 803043
4/23
COMPANY PROFILEBSNL
C.DOT
The Center for Development of Telematics (C-DOT) is the telecom
technology development center of the government.
It was established in August 1984
To design and develop state of the art technologies, products and
solutions
To meet the telecom needs of India, particularly of national
importance in strategic sectors and rural areas
-
7/31/2019 Vikram Thakur 803043
5/23
-
7/31/2019 Vikram Thakur 803043
6/23
Making a telephone call
-
7/31/2019 Vikram Thakur 803043
7/23
Make a telephone call
A telephone call starts when the caller lifts the handsets of the base. Once
the dial tone is heard, the caller uses a rotary or a push button dial mounted
either on the handset or on the base to enter a sequence of digits, the
telephone number of called party.
The switching equipment from the exchange removes the dial tone from theline after the first digit is received and after receiving the last digit, determines
the called party is in the same exchange or a different ones.
If party is in the same exchange or a different ones. If the called is in the
same exchange, burst of ringing current is applied to the called partys line.
If the called party is in different exchange from the caller, the caller exchangeset up the connection over the telephone network to the called partys
exchange.
Its the general process a Telephone Exchange do During
call.
-
7/31/2019 Vikram Thakur 803043
8/23
Architecture of Exchange
A Main Distribution Frame (MDF)
Modules (Computer Room)
Power Plant
-
7/31/2019 Vikram Thakur 803043
9/23
It is a signal Distribution Frame for connecting equipment (Inside
Plant) to cables and Subscriber Carrier equipment (Outside Plant).
The MDF is a termination point within the local Telephone Exchange
where exchange equipment and terminations of Local Loops are
connected by jumper wires.
The MDF usually holds Central Office protective devices
including heat coils and functions as a test point between a line and
the office.
Jumper used in MDF is a twisted wired pair.
-
7/31/2019 Vikram Thakur 803043
10/23
Fig: A Practical Main Distribution Frame
-
7/31/2019 Vikram Thakur 803043
11/23
Architecture of Exchange
A Main Distribution Frame (MDF)
Modules (Computer Room)
Power Plant
-
7/31/2019 Vikram Thakur 803043
12/23
C.DOT exchange has Four Modules
Base Module
Central Module
Administrative Module
Input Output Module
-
7/31/2019 Vikram Thakur 803043
13/23
Base Module
The Basic functions of a base modules are:-
Analog to digital conversion of all signals on analog lines and trunks.
Interface to digital trunks and digital subscriber.
Switching the calls between terminals connected to the same Base Module.
Communication with the AM via the CM for administrative(i.e. Call
processing ) functions.
Provision of special circuits for call processing support e.g. Digital
Tones, announcement, MF/DTMF Senders/receivers.
Provision for local switching Unit(RSU) as well as in case of Single Base
Module Exchange
It is of two types:1. Single Base Modules(SBM)
2. Multi Base Module(MBM)
-
7/31/2019 Vikram Thakur 803043
14/23
Fig General frames Diagram of Base module
-
7/31/2019 Vikram Thakur 803043
15/23
Central module
Central module is responsible for
space switching of inter-Base Module calls,
communication between Base Module and Administrative Modules,
clock distribution and network synchronization.
CM Hardware is distributed in following frames : -
Bus Terminal Unit (BTU) Frame
Space Switch Unit (SSU) Frame
Space Switch Controller Unit (SCU)Administrative Processor Unit (APU)
-
7/31/2019 Vikram Thakur 803043
16/23
-
7/31/2019 Vikram Thakur 803043
17/23
Administrative Module
Status of all module of the exchange is maintained by the AP and whenever a problem
is reported required action is initiated to clear the problem. All the global resource like
trunks. Time slots etc are managed by the A.P. Directory to equipment number
translation for the establishment of a call is performed by AP
All global data is managed by the AP. In a multimodule exchange all thecall processing. Administration and maintenance function are supervised by the
AP.
-
7/31/2019 Vikram Thakur 803043
18/23
Function of APU : - All administrative function in the system Interaction with SSC through central message switches CMS(A,B) (SSC/BM to
IOP via AP).
Communication to ADP.
Administrative Processor (AP) somewhat similar to BP.
Maintain status of all modules of the exchange.
Initiate whenever a problem is reported required action to clear the problem. Switch over of copies, diagnostic of faulty units and put in service units which
are out of service etc, are initiated and supervised by the AP.
Manage all the global resource (like trunks,ts etc.)
Perform directory to equipment no. translation for the established of a call.
Connects of exchange to the operator through IOP.
Handle the man-machine communication.
During initialization of the multimode exchange AP gather initialization requestfrom different BMs, collects code and data from IOP and send it tocorresponding BMs.
-
7/31/2019 Vikram Thakur 803043
19/23
Architecture of Exchange
A Main Distribution Frame (MDF)
Modules (Computer Room)
Power Plant
-
7/31/2019 Vikram Thakur 803043
20/23
POWERPLANTAs we know that, the power is the main source or any organization. It is the
case of E-10B exchange. That is the first requirement of any organization isthe input.
The main source of this exchange is AC supply. However, as soon as the
power supply is gone off, then what is source? No one think on this that the
telephone is always plays its role in the human life. Even if the power supply
gone off. Thus there must be adjustment source of power.
The main parts of the power room are:
Batteries: - these are the instant sources of the power as soon as power isgone off.
UPS (Uninterrupted Power Supply):-the UPS must give supply to thecomputer. As we know there is some equipment which can withstand any type
of power supply, but there are also some instruments which cannot withstand
with this type of power supply, even a microsecond delay will cause the loss of
data.
-
7/31/2019 Vikram Thakur 803043
21/23
Inverter and Converter Unit: - the main use of thissystem is to change AC mains to DC and vice versa as
required by the parts of exchange.
Engine Room:-we know that the batteries are the instantsource of supply but we cannot use it for much larger
time, thus for this, we have an engine to generate the
power supply. They are of 885 KVA. Thus, this room
controls the supply of the engine.
-
7/31/2019 Vikram Thakur 803043
22/23
ConclusionI would like to conclude this training as a very great and enriching experience tointeract with the interesting field in the name of C.Dot BSNL Exchange.
Thus the all things which occurs in telephone Exchange is
Origination : - Origination begins when the subscriber line goes off hookorincoming trunks seized. It receives the incoming digits, selects the digit analysis
tables, and determines the screening information for this call.
Digit Analysis: - It interprets the digits it receives from origination ,select adestination for each call, and passes the dialed digits to routing.
Routing/Screening:- Routing uses the destination information from digit
analysis and screening information origination to select the terminating trunk group
or line.
Charging : - It uses the charging information from routing to expand thecharging data into a formate usable by call accounting process.
Termination : - The last step in call processing is termination. TerminationProcessor is different for calls destined for lines and call destined for trunks.
-
7/31/2019 Vikram Thakur 803043
23/23
Thanks