vehicle health check - mech5mech5.com/sites/default/files/downloads/merc e class (211) e280 cdi...

Vehicle health check Health check done on: 26/01/2016 17:05:20 VIN: WDB211XXXXXXX Plate Number: XXXXXX

AAC - AUTOMATIC AIR CONDITIONING Fault Codes No fault codes were found Parameters Snapshot Parameter Name ValueA32n1 (Blower regulator) : Specified value for requirement of blowercapacity 10 %

A9 (Refrigerant compressor) : Torque 0 Nm

Actual current of component PTC heater booster 0 A

Ambient Temperature 12.9 ºC

B10/4 (In-car temperature sensor) 16.1 ºC

B10/6 (Evaporator temperature sensor) 16.0 ºC

B12/2 (Refrigerant pressure and temperature sensor)/ Refrigerantpressure 5.0 bar

B12/2 (Refrigerant pressure and temperature sensor)/ Temperaturevalue -99.0 ºC

B31/2 (Air humidity sensor) : Current ambient temperature 38 ºC

B31/2 (Air humidity sensor) : Dewpoint -66 ºC

B31/2 (Air humidity sensor) : Relative air humidity -1 %

Coolant Temperature 22 ºC

Current consumption of component A9 (Refrigerant compressor) 0 mA

Cutoff because of overvoltage at terminal 30 NO

Cutoff because of undervoltage at terminal 30 YES

DF signal ( CAN bus ) 127 %

Engine Speed 0 RPM

Generator output NOT OK

Heating capacity : Left 100 %

Heating capacity : Right 100 %

/ 27

Andrew.Steer

Text Box

MERCEDES E CLASS (211) E280 CDI AVANTGARDE 2007

Heating element 1 : Open circuit Not present

Heating element 1 : Short circuit Not present















M2/15 (Left and right footwell flaps actuator) : Alignment of positioningmotors OK

M2/15 (Left and right footwell flaps actuator) : Communication faultbetween control module N22 (AAC [KLA] control and operating unit)and M2/15 (Left and right footwell flaps actuator)

NO

M2/15 (Left and right footwell flaps actuator) : Current flap adjustmenttravel of motor 2146

M2/15 (Left and right footwell flaps actuator) : Current position ofactuator motor 2146

M2/15 (Left and right footwell flaps actuator) : Electrical fault NO

M2/15 (Left and right footwell flaps actuator) : Excess temperature NO

M2/15 (Left and right footwell flaps actuator) : Mechanical fault NO

M2/15 (Left and right footwell flaps actuator) : Position of actuatormotor specified by control unit 2146

M2/15 (Left and right footwell flaps actuator) : Stored flap adjustmenttravel of motor 2146

M2/16 (Left and right defroster flaps actuator) : Alignment of positioningmotors OK

M2/16 (Left and right defroster flaps actuator) : Communication faultbetween control module N22 (AAC [KLA] control and operating unit)and M2/16 (Left and right defroster flaps actuator)

NO

M2/16 (Left and right defroster flaps actuator) : Current flap adjustmenttravel of motor 2018

/ 27

M2/16 (Left and right defroster flaps actuator) : Current position ofactuator motor 2018

M2/16 (Left and right defroster flaps actuator) : Electrical fault NO

M2/16 (Left and right defroster flaps actuator) : Excess temperature NO

M2/16 (Left and right defroster flaps actuator) : Mechanical fault NO

M2/16 (Left and right defroster flaps actuator) : Position of actuatormotor specified by control unit 2018

M2/16 (Left and right defroster flaps actuator) : Stored flap adjustmenttravel of motor 2018

M2/22 (Center vent flap positioning motor) : Excess temperature NO

M2/22 (Center vent flap positioning motor) : Alignment of positioningmotors OK

M2/22 (Center vent flap positioning motor) : Communication faultbetween control module N22 (AAC [KLA] control and operating unit)and M2/22 (Center vent flap positioning motor)

NO

M2/22 (Center vent flap positioning motor) : Current flap adjustmenttravel of motor 2621

M2/22 (Center vent flap positioning motor) : Current position of actuatormotor 628

M2/22 (Center vent flap positioning motor) : Electrical fault NO

M2/22 (Center vent flap positioning motor) : Mechanical fault NO

M2/22 (Center vent flap positioning motor) : Position of actuator motorspecified by control unit 628

M2/22 (Center vent flap positioning motor) : Stored flap adjustmenttravel of motor 2621

M2/5 (Fresh and recirculated air flaps actuator) : Alignment ofpositioning motors OK

M2/5 (Fresh and recirculated air flaps actuator) : Communication faultbetween control module N22 (AAC [KLA] control and operating unit)and M2/5 (Fresh and recirculated air flaps actuator)

NO

M2/5 (Fresh and recirculated air flaps actuator) : Current flapadjustment travel of motor 2056

M2/5 (Fresh and recirculated air flaps actuator) : Current position ofactuator motor 0

M2/5 (Fresh and recirculated air flaps actuator) : Electrical fault NO

M2/5 (Fresh and recirculated air flaps actuator) : Excess temperature NO

M2/5 (Fresh and recirculated air flaps actuator) : Mechanical fault NO

M2/5 (Fresh and recirculated air flaps actuator) : Position of actuatormotor specified by control unit 0

M2/5 (Fresh and recirculated air flaps actuator) : Stored flap adjustmenttravel of motor 2056

M2/6 (Left blending air flap actuator) : Alignment of positioning motors OK

/ 27

M2/6 (Left blending air flap actuator) : Communication fault betweencontrol module N22 (AAC [KLA] control and operating unit) and M2/6(Left blending air flap actuator)

NO

M2/6 (Left blending air flap actuator) : Current flap adjustment travel ofmotor 1875

M2/6 (Left blending air flap actuator) : Current position of actuatormotor 0

M2/6 (Left blending air flap actuator) : Electrical fault NO

M2/6 (Left blending air flap actuator) : Excess temperature NO

M2/6 (Left blending air flap actuator) : Mechanical fault NO

M2/6 (Left blending air flap actuator) : Position of actuator motorspecified by control unit 0

M2/6 (Left blending air flap actuator) : Stored flap adjustment travel ofmotor 1875

M2/7 (Right blending air flap actuator) : Alignment of positioning motors OK

M2/7 (Right blending air flap actuator) : Communication fault betweencontrol module N22 (AAC [KLA] control and operating unit) and M2/7(Right blending air flap actuator)

NO

M2/7 (Right blending air flap actuator) : Current flap adjustment travelof motor 1924

M2/7 (Right blending air flap actuator) : Current position of actuatormotor 0

M2/7 (Right blending air flap actuator) : Electrical fault NO

M2/7 (Right blending air flap actuator) : Excess temperature NO

M2/7 (Right blending air flap actuator) : Mechanical fault NO

M2/7 (Right blending air flap actuator) : Position of actuator motorspecified by control unit 0

M2/7 (Right blending air flap actuator) : Stored flap adjustment travel ofmotor 1924

N70b1 (In-car temperature sensor) OCP 17.4 ºC

PTC heater booster OK

Request to component A9 (Refrigerant compressor) 0 %

Shutdown due to excessive temperature NO

Supply Voltage 11 V

Terminal 58d 0 %

Vehicle speed 0 km/h

/ 27

ABS - ANTI LOCK BRAKE MODULE Fault Codes No fault codes were found Parameters Snapshot Parameter Name ValueA7/3b3 (Left front pressure sensor) 0.0 bar

A7/3b5 (Left rear pressure sensor) 0.0 bar

Brake pressure 0.0 bar

CAN bus : N72/1s1 (ESP OFF Switch) Off

Component S9/1 (Stop lamp switch), NC contact ON

Component S9/1 (Stop lamp switch), NO contact OFF

Cruise control switch Not Operated

Front left rpm sensor, gap OK (Limit value)

Front right rpm sensor, gap OK (Limit value)

Kilometer reading warning no. 1 NOTAVAILABLE km



Lateral acceleration 0.3 m/s²

N49 (Steering angle sensor) 50.0 º

Rear left rpm sensor, gap OK (Limit value)

Rear right rpm sensor, gap OK (Limit value)

Rotational direction of left front wheel Invalid

Rotational direction of left rear wheel Invalid

Rotational direction of right front wheel Invalid

Rotational direction of right rear wheel Invalid

Rotational speed 0.1 º/s

S12 (Parking brake indicator switch) OFF

Speedtronic active Yes

Status 'Tire pressure loss warner' ---

Voltage supply of solenoid valves 11.8 V

Voltage supply of solenoid valves (internal values) 11.6 V

Wheel speed at left front axle 0.0 km/h

/ 27

AGW - AUDIO GATEWAY (MOST NETWORK MANAGEMENT, DIAGNOSISGATEWAY, RADIO TUNER) Fault Codes No fault codes were found Parameters Snapshot

AIRBAG (SRS) Fault Codes No fault codes were found Parameters Snapshot

ASSYST - ACTIVE SERVICE SYSTEM Fault Codes No fault codes were found Parameters Snapshot

Wheel speed at left rear axle 0.0 km/h

Wheel speed at right front axle 0.0 km/h

Wheel speed at right rear axle 0.0 km/h

Parameter Name ValueRead ECU identification ZB number 211870668900

Parameter Name ValueVIN WDB2110202B266858

/ 27

ASSYST PLUS Fault Codes No fault codes were found Parameters Snapshot

Parameter Name ValueCurrent quality factor for engine oil 1.67

Distance driven since last oil change 9076 km

Remaining distance 15924 km

Remaining time 323 days

Unevaluated time 42 days

Parameter Name ValueAverage mileage per day 80 Km

Confirmation of an oil fill as per sheet 229.3 NOT PERMITTED

Confirmation of an oil fill as per sheet 229.5 NOT PERMITTED

Confirmation of an oil fill as per sheet Standard oil Permitted

Cylinder shut-off Not Active

Day cycle counter 185 Days

Days until next Service 323 Day

Display mode Service not yet due

Display unit for trabel distance Miles

Distance unit Miles

Driving distance till next service 9894 Km

Engine off time 14 min

Engine running Not recognized

Engine speed 0.0 RPM

Engine temperature 22 °C

Engine torque -65 Nm

Estimated work total 145

Front axle - 100% brake wear sensor Not Activated

Front axle - 50% brake wear sensor Activated

/ 27

Language English

Lateral acceleration -9.13 m/s²

Main odometer 240389 Km

Maintenance program data Valid

Maximum engine torque 142 Nm

Minimum engine torque -89 Nm

Number of entries in service memory 11

Number of maintenance items configured 37

Oil level check Not Active

Oil temperature 36 °C

Pedal value sensor 0.0 %

Rear axle - 100% brake wear sensor Not Activated

Rear axle - 50% brake wear sensor Not Activated

Remaining distance 9894

Remaining time 323 Days

SERVICE 10 Open

SERVICE 11 Due

SERVICE 12 Open

SERVICE 13 Due

SERVICE 14 Due

SERVICE 15 Open

SERVICE 16 Open

SERVICE 2 Open

SERVICE 20 Open

SERVICE 3 Open

SERVICE 4 Open

SERVICE 5 Open

SERVICE 6 Due

SERVICE 7 Open

SERVICE 8 Open

SERVICE 9 Open

Service Code C

Service Code C

Special service request in display Not Activated

Stop lamp switch Not Active

/ 27

CGW - CENTRAL GATEWAY Fault Codes No fault codes were found Parameters Snapshot Not scanned

DCM-FL - DOOR CONTROL MODULE FRONT LEFT Fault Codes No fault codes were found Parameters Snapshot

Total distance driven 240389 Km

Total time 3001 Day

Vehicle handover allowed YES

Vehicle speed 0 Km/h

Parameter Name ValueActual value Mirror lens position 'right/left' 0.00

Actual value Mirror lens position 'up/down' 0.00

Actuation mirror lens adjustment (left/right) Not Actuated

Actuation Mirror lens adjustment (up/down) Not Actuated

Central locking system motor actuated in 'CLOSE' direction NO

Central locking system motor actuated in 'OPEN' direction NO

Closing relay is actuated NO

Component M10/3 (Left front power window motor) is blocked NO

Convenience function for central closing/opening activated NO

Current consumption of component M10/3 (Left front power windowmotor) 0.0 A

E17/11 (Left front door inside handle illumination) OFF

E17/19 (Left front door warning light) OFF

/ 27

DCM-FR - DOOR CONTROL MODULE FRONT RIGHT Fault Codes No fault codes were found Parameters Snapshot

E17/3 (Left front door entry/exit lamp) OFF

E6/5 (Left exterior mirror turn signal lamp) Not Actuated

Hall sensor signal 1 1


Infrared signal detected NO

Infrared signal fault detected NO

M21/1e1 (Left outside mirror ambient lamp) OFF

Mirror Heater Not Actuated

Mirror housing adjustment Not Operated

ON/OFF ratio circuit 58d 0 %

Opening relay is actuated NO

Position of left front window 0

Position of mirror selection switch Driver

Power supply 11.7 V

Power Window Normalized

Power window has detected obstruction NO

Power window relay operates NO

Receive signal for comfort function NO

S21/2 (Front passenger power window switch) Not Operated

Specified value Mirror lens position 'right/left' 0.00

Specified value Mirror lens position 'up/down' 0.00

Switch illumination Terminal 58d OFF

Switch mirror housing adjustment operated Not operated

Parameter Name ValueActual value Mirror lens position 'right/left' 0.00 V

Actual value Mirror lens position 'up/down' 0.00 V

/ 27

Actuation mirror lens adjustment (left/right) Not Operated

Actuation Mirror lens adjustment (up/down) Not Operated

Central locking system motor actuated in 'CLOSE' direction NO


Childproof lock activated NO


Component M10/4 (Right front power window motor) is blocked NO

Convenience function for central closing/opening activated NO

Current consumption of component M10/4 (Right front power windowmotor) 0.0 A

E17/12 (Right front door inside handle illumination) OFF

E17/21 (Right front door warning light) OFF

E17/4 (Right front door entry/exit lamp) OFF

E6/6 (Right exterior mirror turn signal lamp) Not Actuated



Infrared signal detected NO

Infrared signal fault detected NO

LED 'Childproof lock activated' OFF

LED 'Trunk lid opened' OFF

M21/2e1 (Right outside mirror ambient lamp) OFF

Mirror Heater Not Actuated

Mirror housing adjustment Not Operated



Position of mirror selection switch M21/7 (Front passengerexterior mirror)

Position of right front window 270

Position of right front window 270

Power supply 11.8 V




Receive signal for comfort function NO

S20/1s1 (Left front power window switch) Not Operated

S20/1s2 (Right front power window switch) Not Operated

/ 27

DCM-RL - DOOR CONTROL MODULE REAR LEFT Fault Codes No fault codes were found Parameters Snapshot

S20/1s3 (Left rear power window switch) Not Operated

S20/1s4 (Right rear power window switch) Not Operated

S20/1s5 (Rear side windows child safety lock switch) Not operated

Specified value Mirror lens position 'right/left' 0.00 V

Specified value Mirror lens position 'up/down' 0.00 V


Switch mirror housing adjustment operated Not Operated

Switch 'Trunk lid remote closing' is operated NO

Switch 'Trunk lid remote release' is operated NO

Switches Mirror lens adjustment (left/right) Not Operated

Switches Mirror lens adjustment (up/down) Not Operated

Parameter Name ValueCentral locking system motor actuated in 'CLOSE' direction NO


Childproof lock activated No


Component M10/5 (Left rear power window motor) is blocked No

Current consumption of component M10/5 (Left rear power windowmotor) 0 A

Current consumption of component M10/5 (Left rear power windowmotor) 0.0 A

E17/13 (Left rear door inside handle illumination) OFF

E17/20 (Left rear door warning light) OFF

Exit light OFF




/ 27

DCM-RR - DOOR CONTROL MODULE REAR RIGHT Fault Codes No fault codes were found Parameters Snapshot



Position of rear left window 0

Position of rear left window 0




S21/3 (Left rear power window switch) Not Operated

Supply voltage 11.7 V


Parameter Name ValueCentral locking system motor actuated in 'CLOSE' direction NO


Childproof lock is activated NO


Component M10/6 (Right rear power window motor) is blocked NO

Current consumption of component M10/6 (Right rear power windowmotor) 0.0 A

Current consumption of component M10/6 (Right rear power windowmotor) 0.0 A

E17/14 (Right rear door inside handle illumination) OFF

E17/22 (Right rear door warning light) OFF

E17/6 (Right rear door entry/exit lamp) OFF





/ 27

EGS - ELECTRONIC TRANSMISSION CONTROL Fault Codes No fault codes were found Parameters Snapshot


Position of rear right window 0

Position of rear right window 0




S21/4 (Right rear power window switch) Not Operated

Supply voltage 11 V


Parameter Name ValueActual gear - - -

Battery voltage 11.42 V

Battery voltage VGS3 0.45 V

Calculated gear Not Active

CAN km-Zaehler: lesen 40388 km

Current error codes NO

Drehzahlen: Geschwindigkeit h 0 Km/h

Emergency operation mode YES

End of line Test: Zielgang PARK / POSITION

Engine speed 0 RPM

Engine torque 65471 Nm

Gradient 0.00 %

Highest gear Init value

Internal transmission speed 0 RPM

Kickdown Not Active

Lowest gear Init value

/ 27

ELECTRONIC DASHBOARD Fault Codes No fault codes were found Parameters Snapshot

Oil temperature of automatic transmission 28 °C

Operating mode Normal mode

Output speed 0 RPM

Output speed 0 RPM

Position of selection range valve P

Request 'Neutral position' NO

Start enable Not Active

Status of torque converter lockup clutch Open

Steering wheel shift button 'MINUS' (-) Not Actuated

Steering wheel shift button 'PLUS' (+) Not Actuated

Torque converter slip speed 0 RPM

Transmission mode Standard

Turbine speed 0 RPM

Value of accelerator pedal sensor 0 %

Parameter Name ValueAmbient Temperature 13.0 ºC

Days since initial registration 3001 days

Fuel tank level minimum Not reached

Status of adaptation to drive authorization system Learned

Status of instrument cluster drive authorization system Identifier corresponds tovehicle

Tank Capacity 26.0 L

Vehicle speed 0 MPH

/ 27

ENGINE ELECTRONICS (PETROL/DIESEL) Fault Codes P2270 N14/3 (Glow time output stage) (Present) Parameters Snapshot Parameter Name Value"Set + accelerate" cruise control switch NO

"Set + decelerate" cruise control switch NO

Air Mass 0 mg/hub

Atmospheric pressure 981 hPa

B37 (Accelerator pedal sensor) Channel 1 0 %

B37 (Accelerator pedal sensor) Channel 2 0 %

Boost Air Temperature 18.0 ºC

Boost Pressure 984 hPa

Charge pressure positioner 27.6 %

Coolant temperature 22.1 ºC

Cruise control switch in 'Off' position NO

Cruise control switch in position 'Resume' NO

Current injected quantity 24.3 mm3/Hub

Current kilometer reading 40388 Km

Cylinder 1 0.00

Cylinder 2 0.00

Cylinder 3 0.00

Cylinder 4 0.00

Cylinder 5 0.00

Cylinder 6 0.00

Electric fuel pump OFF

Engine speed 0 RPM

Exhaust Back Pressure 974 hPa

Fuel tank level 26 L

Fuel Temperature 21 ºC

Fuel Temperature 567 ºC

Intake Air Pressure 981 hPa

/ 27

ESM - ELECTRONIC SELECTOR MODULE Fault Codes No fault codes were found Parameters Snapshot

Pressure Control Valve 11 %

Rail Pressure 8 bar

Rail pressure control Y74/1 (Pressure regulatorvalve)

Selector lever position P/N YES

Speedtronic (cruise control or variable speed limiter) YES

Start enable YES

Start enable YES

Start enable from control module N15/3 (ETC [EGS] control unit) YES

Start enable from control module N15/3 (ETC [EGS] control unit) YES

Terminal 15 YES

Terminal 50 (input) NO

Terminal 50 (Output, starter actuation) OFF

Transmission neutral contact YES

Vehicle speed 0 km/h

Voltage terminal 87 12.08 V

Y94 (Quantity control valve) 0 %

Parameter Name ValueBrake Pedal Not Operated

Brake torque 0 Nm

'Negative' touch pushbutton Not Operated

'Positive' touch pushbutton Not Operated

R/P lock Not Operated

S16/5s1 (Transmission mode switch) Not Operated

Selector lever position P

'Shift lock' function Not Operated

Status of locking solenoid Not Operated

/ 27

EZS - ELECTRONIC IGNITION SWITCH Fault Codes No fault codes were found Parameters Snapshot

Terminal 15 11.90 V

Parameter Name ValueCoil for energy supply of transmitter key is switched off YES

Control module ESL is activated DISABLED

Control module ESL is initialized DISABLED

Control module ESL is personalized DISABLED

Control module EZS is activated DISABLED

Control module EZS is initialized ENABLED

Control module EZS is personalized DISABLED

ESL: Start enable YES

EZS: Turn enable issued YES

Key in position 'H0' (auxiliary contact) NO

Key inserted in control module EZS YES

Key or key track last used 1

ME motor electronics: Start enable YES

Output 'Circuit 15' ON

Output 'Circuit 15R' ON

Output 'Circuit 50' OFF

Output Terminal 15 (CAN) ON

Output terminal 15C (CAN) ON

Output Terminal 15R (CAN) ON

Output Terminal 50 (CAN) OFF

Power supply 11.92 V

Second last key or key track used 2

Serial number EZS �XuA`a&

Test counter of control module ESL 0

/ 27

MRM - STEERING COLUMN MODULE Fault Codes No fault codes were found Parameters Snapshot

Test counter of control module EZS 0

The transport protection of control module ESL is detached ENABLED

The transport protection of control module EZS is detached NO

Version of control module EZS Series

Parameter Name ValueAbrupt change in steering angle Ok

Button for rear window wiper 'INTERMITTENT and WASH' Not Operated

N49 (Steering angle sensor) INITIALIZED

S110s1 (Scroll forward/back pushbutton) Not Operated

S110s3 (System select pushbutton) Not Operated

S110s5 or S111s5 (Pushbutton for fanfare horns) OFF

S111s1 (pushbutton + and -, setting specific functions and volumecontrol) Not Operated

S111s3 (Accept/terminate phone call pushbutton) Not Operated

S40/4 (CC switch with variable speed limiter) Not operated

S4s1 (Left and right turn signal switch) Not operated

S4s2 (Headlamp flasher and high beam switch) Not Operated

S4s4 (Windshield washer system switch) Not Operated

S4s5 (Wipe switch) Intermittent

S59/1s1 (Steering column adjustment raise/lower, forward/back switch) Not operated

S59/1s2 (Steering wheel heater switch) Not operated

S93/2 (VCS switch) Not Operated

Status 'N49 (Steering angle sensor)' OK

Status 'Steering rotation signal' Ok

Steering angle 50.0 °

Steering rotation 1

/ 27

OCP - OVERHEAD CONTROL PANEL Fault Codes No fault codes were found Parameters Snapshot

Steering rotation marks Plus (+): Steering rotation tothe left

Switch for rear window wiper 'INTERMITTENT' Not Operated

Switch statuses Not operated

Voltage at terminal 30 11.7 V

Parameter Name ValueA67e1 (Left reading lamp) OFF

A67e2 (Right reading lamp) OFF

Day/night switchover Not Okay

Dimming stage of interior rearview mirror 0

E15/3 (Rear interior lamp) OFF

E17/15 (Right front footwell lamp) ON

E17/16 (Left front footwell lamp) OFF

E17/17 (Right rear footwell lamp) OFF

E17/18 (Left rear footwell lamp) OFF

E17/19 (Left front door warning light) OFF

E17/20 (Left rear door warning light) OFF

E17/21 (Right front door warning light) OFF

E17/22 (Right rear door warning light) OFF

E17/3 (Left front door entry/exit lamp) OFF

E17/4 (Right front door entry/exit lamp) OFF

E17/5 (Left rear door entry/exit lamp) OFF

E17/6 (Right rear door entry/exit lamp) OFF

Fault status of light sensor OK

If the driving lights are switched off, the vehicle lights are automaticallyswitched on or off depending on the ambient brightness. Switched on

Interior temperature 17.2 ºC

/ 27

REAR SAM - REAR SIGNAL ACQUISITION AND ACTUATION MODULE Fault Codes B1032 Component S88/8 (Trunk lid exterior operation switch) is stuck or has a short circuit. (Present) Parameters Snapshot

Light Sensor Not Okay

M21/1e1 (Left outside mirror ambient lamp) OFF

M21/2e1 (Right outside mirror ambient lamp) OFF

N70e1 (Front dome lamp) OFF



N70s3 (Door contact ON and OFF switch) ON

Output voltage at terminal 15R ON

Status 'Rain sensor' OK

Travel through a tunnel OK

Voltage supply at control module 0.00 V

Wiper stage 0

Parameter Name ValueE18/4 (Right trunk lamp) OFF

E18/5 (Left trunk lamp) OFF

E19/1 (Left license plate lamp) OFF

E19/2 (Right license plate lamp) OFF

E21 (Center high-mounted stop lamp) OFF

E3e1 (Outer left turn signal lamp) OFF

E3e2 (Outer left taillamp, parking lamp, rear fog lamp)(Function 'Rearfoglight') OFF

E3e2 (Outer left taillamp, parking lamp, rear fog lamp)(Function 'Rearfoglight') OFF

E3e3 (Left backup lamp) OFF

E3e4 (Left stop lamp) OFF

E3e5 (Inner left taillamp, rear fog lamp)(Function 'Rear foglight') OFF

E3e5 (Inner left taillamp, rear fog lamp)(Function 'Tail light') OFF

/ 27

E3e7 (Inner left turn signal lamp) OFF

E4e1 (Outer right turn signal lamp) OFF

E4e2 (Outer right taillamp, parking lamp, rear fog lamp)(Function 'Rearfoglight') OFF

E4e2 (Outer right taillamp, parking lamp, rear fog lamp)(Function 'Rearfoglight') OFF

E4e3 (Right backup lamp) OFF

E4e4 (Right stop lamp) OFF

E4e5 (Inner right taillamp, rear fog lamp)(Function 'Rear foglight') OFF

E4e5 (Inner right taillamp, rear fog lamp)(Function 'Tail light') OFF

E4e7 (Inner right turn signal lamp) OFF

Fuel tank level 84 %

M53/1 (Left rear head restraint motor) OFF

M53/2 (Right rear head restraint motor) OFF

M53/3 (Center rear head restraint motor) OFF

N10/2kG (Fuel filler cap pole reversal relay 1) (Lock filler cap.) OFF

N10/2kH (Fuel filler cap pole reversal relay 2) (Unlock filler cap.) OFF

S132/1 (Rear seat unlocking switch, left) INTERLOCKED Not operated

S132/1 (Rear seat unlocking switch, left) UNLOCKED Not operated

S132/2 (Rear seat unlocking switch, right) INTERLOCKED Not operated

S132/2 (Rear seat unlocking switch, right) UNLOCKED Not operated

S17/3 (Left front door contact switch) Door Closed

S17/4 (Right front door contact switch) Door Open

S17/5 (Left rear door contact switch) Door Closed

S17/6 (Right rear door contact switch) Door Closed

S54/5 (Left rear backrest angle switch) Not Operated

S54/6 (Right rear backrest angle switch) Not Operated

S88/4 (Locking pawl rotary tumbler switch) Not operated

S88/6 (Trunk lid contact switch) Not operated

S88/8 (Trunk lid exterior operation switch) Operated

Terminal 15 ON

Terminal 54 OFF

Trunk lid unlocking OFF

/ 27

RevETR-LF - LEFT FRONT REVERSIBLE EMERGENCY TENSIONINGRETRACTOR Fault Codes No fault codes were found Parameters Snapshot

RevETR-RF - RIGHT FRONT REVERSIBLE EMERGENCY TENSIONINGRETRACTOR Fault Codes No fault codes were found Parameters Snapshot

SAMB - SIGNAL ACQUISITION AND CONTROL MODULE PASSENGERSIDE Fault Codes No fault codes were found

Parameter Name ValueExecution frequency of belt tensioner function 1


Parameter Name ValueExecution frequency of belt tensioner function 1


/ 27

Parameters Snapshot

SAM-F - SIGNAL ACQUISITION AND ACTUATION MODULE FRONT Fault Codes No fault codes were found Parameters Snapshot

Parameter Name ValueSelector lever in position P Yes

Terminal 30 11.73 V

Parameter Name ValueAutomatic driving lamps OFF

B14 (Ambient temperature display temperature sensor) 13.0 ºC

Brake fluid level Ok

Coolant Level OK

Current consumption of component A9 (Refrigerant compressor) 0 mA

Driving lamps OFF

Fog light OFF

Left parking lamp OFF

Parking brake Released

Rear foglight OFF

Right front brake lining Okay

Right parking lamp OFF

Right rear brake lining Okay

Side lamp OFF

Speed status of control unit SBC Vehicle rolling

Stop lamp switch output at control unit SBC OFF

System status of control unit SBC Passive

Terminal 15 ON

Terminal 15R ON

Terminal 30 11.74 V

/ 27

SD - SYSTEM DIAGNOSIS Fault Codes No fault codes were found Parameters Snapshot Not scanned

SOUND SYSTEM Fault Codes No fault codes were found Parameters Snapshot

UCP - UPPER CONTROL PANEL Fault Codes No fault codes were found Parameters Snapshot

Terminal 61 ON

Washer Fluid Level OK

Parameter Name ValuePower supply 12.0 V

Parameter Name ValueN72/1s1 (ESP OFF switch) Not operated

N72/1s10 (Left front HS switch) Not Operated

N72/1s11 (Right front HS switch) Not Operated

N72/1s13 (Left front seat ventilation switch) Not Operated

/ 27

XALWA-L - XENON HEADLAMP, LEFT Fault Codes No fault codes were found Parameters Snapshot

XALWA-R - XENON HEADLAMP, RIGHT

N72/1s14 (Right front seat ventilation switch) Not Operated

N72/1s15 (UCP carrier open/close switch) Not Operated

N72/1s4 (Rear head restraints switch) Not Operated

N72/1s5 (Hazard warning system switch) Not Operated

N72/1s6 (Interior central locking and ATA function display switch) :CLOSE Not Operated

N72/1s6 (Interior central locking and ATA function display switch) :OPEN Not Operated

Voltage at Terminal 30 11.9 V

Parameter Name ValueIgnition auxiliary voltage 1 V

Operating hours counter of xenon bulb [ E1 e 10 (Left bi-xenon lampwith integral ignition module)] 190340 min

Signal from component B22/2 (Front axle level sensor) 2.62 V

Spring compression at front axle -12 mm

Spring compression at rear axle -14 mm

Tourist mode (Symmetrical light distribution) OFF

Transformer voltage 0 V

Vertical motor position (Headlamp range adjustment) (Specified value) -2 %


Voltage at terminal 56b (Low beam) 0.0 V

Xenon bulb power (Specified value) 35 W

Zero position adjustment Valid

/ 27

Fault Codes B1004 Status of terminal 56b implausible (Present) Parameters Snapshot Parameter Name ValueIgnition auxiliary voltage 362 V

Operating hours counter of xenon bulb [ E2 e 10 (Right bi-xenon lampwith integral ignition module)] 169475 min

Tourist mode (Symmetrical light distribution) OFF

Transformer voltage 0 V

Vertical motor position (Headlamp range adjustment) (Specified value) -2 %


Voltage at terminal 56b (Low beam) 7.9 V

Xenon bulb power (Specified value) 35 W

/ 27

vehicle health check - mech5mech5.com/sites/default/files/downloads/merc e class (211) e280 cdi...

Documents