upustvo mašina upustvo mašina za suđe

8/9/2019 Upustvo Maina upustvo maina Za Sue

1/31


2/31


3/31

en IndexSafety instructions 4. . . . . . . . . . . . .

Getting to know your appliance 6. .

Water softener 7. . . . . . . . . . . . . . . .

Filling the special salt container 8. .

Filling the rinse-aid container 9. . . .

Unsuitable dishes 10. . . . . . . . . . . . .

Arranging crockery, glasses, etc.

in the dishwasher 11. . . . . . . . . . . . . .

Detergents 15. . . . . . . . . . . . . . . . . . .

auto 3in1 16. . . . . . . . . . . . . . . . . . . . .

Programme overview 18. . . . . . . . . .

Washing dishes 19. . . . . . . . . . . . . . .

Maintenance and care 21. . . . . . . . . .

Fault finding 23. . . . . . . . . . . . . . . . . .

Customer Service 25. . . . . . . . . . . . .

Information 26. . . . . . . . . . . . . . . . . . .

Installation 26. . . . . . . . . . . . . . . . . . . .


4/31

en

4

Safety instructions

Delivery

Immediately check the packaging anddishwasher for any damage which may

have been caused in transit. Do not usea damaged appliance, but consult yoursupplier.

Please dispose of packaging materialproperly: The corrugated cardboard consists

mainly of waste paper. The polystyrene moulded parts

have been foamed without anyCFCs.

The polyethylene film (PE) consistspartly of secondary raw material.

The wooden frames (if fitted) aremade of residual wood and areuntreated.

The hoops (if fitted) consist ofpolypropylene (PP).

Installation

Install and connect the applianceaccording to the installation andassembly instructions.

The dishwasher must NOT be

connected to the power supply duringinstallation.

Ensure that the protective conductorsystem of the domestic electricitysupply has been installed correctly.

Electrical connection conditions mustcorrespond with the specifications onthe rating plate of the dishwasher.

Built-under and built-in appliancesshould always be installed under acontinuous work surface which isattached to the adjacent cupboards, inorder to ensure that the appliance isentirely stable.

After the appliance has been installed,the mains plug should still be easilyaccessible.

Not on all models:The plastic housing on the water input

contains an electrically operated valve.The connecting wires are inside theinlet hose. Do not cut through this hoseand do not immerse the plastic housingin water.

Warning

For safety reasons, if the appliance is notfitted in a recess, thereby making a sidewall accessible, the door hinge area

should be covered at the side.(Risk of injury)Covers are available as optionalaccessories from customer services orspecialist stores.


5/31

en

5

In daily use

Warning

Knives and other utensils with sharp pointsmust be placed in the baskets either flat or

with the points downwards.Use the dishwasher only in thehousehold and only for its designedpurpose, i.e. for washing domesticdishes.

Do not lean or sit on the open door.The appliance could tip.

The water in the appliance is notdrinking water.

Do not add any solvents to the washing

chamber. Danger of explosion!

Open the door carefully when theprogramme is still running. Water couldspray out of the appliance.

To prevent injuries, e.g. caused bystumbling, open the dishwasher onlybriefly in order to load and unload thedishwasher.

Read and observe the safety

information and instructions for use onthe packaging for cleaning and rinsingagents.

Children in the household

Do not let infants play or operate thedishwasher.

Keep cleaning and rinsing agents out ofthe reach of infants.

Keep infants away from the open

dishwasher. It could contain residue ofthe cleaning agent.

Child lock *

* on applicable models

Please refer to the drawings enclosed inthe envelope

40 Engaging the child lock

41 Opening the door with the child lock

engaged42 Disengaging the child lock

If a fault occurs

Repairs or other work on thedishwasher should only be carried outby a qualified specialist.

The dishwasher must be disconnectedfrom the electricity supply before anyrepairs or other work are started. Pullthe mains plug out of the wall socket orswitch off at the fuse box. Grasp theplug to remove it from the socket; donot tug on the cable. Turn the water offat the tap.

When disposing of oldappliances

Appliances that have reached the endof their service life should be renderedinoperable in order to exclude thepossibility of subsequent accidents. Pullthe mains plug out of the wall socket,cut through the connecting cable anddisable the door lock.

Take the appliance to a designatedwaste disposal centre.

WarningChildren could get locked in the appliance(risk of suffocation) or get stuck in otherpositions.Therefore: Remove the mains plug, cut themains wire and set aside. Damage thedoor lock so that the door can no longerbe closed.


6/31

en

6

Getting to know yourappliance

Diagrams of the control panel and theinterior of the appliance can be foundin the envelope at the front.

Individual positions are referred to inthe text.

Control panel

1 Main switch

2 Door handle

3 Numerical display

4 Timer programming *

5 Button for UPPER RACK washing

function *

6 Programme buttons

7 LOW SALT indicator

8 LOW RINSE-AID indicator

Always keep the fascia clean and freeof grease. Clean with a dry or moistcloth only. Do notuse abrasiveor scouring detergents.

Appliance interior

20 Upper basket with 2-tiered cup rack

21 Additional cutlery basket for the top

basket *

22 Upper spray arm

23 Lower spray arm24 Container for special salt with level

indicator *

25 Filters

26 Cutlery basket

27 Lower basket

28 Locking mechanism

29 Container for rinse-aid, with level

indicator

30 Detergent compartment

31 Nameplate

* not on all models

You will need to purchase thefollowing before using thedishwasher for the first time:

special salt for use in dishwashers

detergent rinse-aid

Only use products, which are suitable fordishwashers.


7/31

en

7

Water softener

In order to rinse dishes and glassessatisfactorily, the dishwasher requires softwater, i.e. containing little or no lime,otherwise water stains will be left behind

on crockery and glasses, etc.If the tap water exceeds a certain level ofhardness, it must be softened, i.e.decalcified, so that it can be used in thedishwasher.This is achieved by adding a special saltto the water softener inside thedishwasher.The water softener, that is the requiredamount of salt, is set up according to how

hard the tap water is.Setting up the water softener

Determine the level of hardness of yourtap water. Your local water company orservice agent can help you with this.

Identify setting from the following waterhardness table.

Water hardness table

Press and hold the B programme

button, and set the main switch 1 toON, before releasing the programmebutton again.

The indicator lamp for the B button

flashes, as does the figure

in the numerical display. The latterrepresents the value that was pre-set inthe factory.

To change the setting:

Press the B programme button 6 .

Every time the button is pressed, thefigure increases by one. After reaching

, the display starts at again.

Set the main switch 1 to OFF. The

new setting is stored in the appliancesmemory.

Approx. 4 litres of water are required forregenerating the water softening system.The overall water consumption per loadcan therefore be increased by between 0and a maximum of 4 litres according to thewater hardness setting.


8/31

en

8

Filling the special saltcontainer

How the salt works

While washing is taking place, salt isautomatically rinsed out of the saltcontainer into the water softener where itdissolves the lime in the water.The dissolved lime is pumped out of thedishwasher. The water softening system isthen ready for the next load.This process of regeneration can onlyfunction when the salt is dissolved inwater.

Unscrew the lid on the salt container 24 .

Before you use the dishwasher for the firsttime, pour approx. 1 litre of water into thesalt container.

Use the enclosed salt filler.

Refill with salt (do not use edible salt)until the salt dispenser is full (max. 1.5 kg).When the salt dispenser is being refilled,water is displaced and drains away.

Therefore always refill the salt dispenserimmediately before switching on thedishwasher (to prevent corrosion). As aresult, the overflowing salt solution will beimmediately diluted and rinsed out. Thenremove salt residue from the filler area andscrew on the dispenser cover, ensuringthat it is not fitted askew.

The LOW SALT indicator 7 on the frontpanel will light up initially but will extinguishagain after a short period when the saltsolution has become sufficientlyconcentrated.

Note

When the control is set to , it is

not necessary to fill up with saltas none will be consumed whilethe dishwasher is operating. TheLOW SALT indicator is switchedoff. If the control is set between

and , then salt must be

added to the dispenser.

Do not pour detergent into thecontainer for special salt. Thiswould destroy the watersoftener.

Salt refill indicator

As soon as the salt refill indicator 7 is lit

on the control panel, refill with saltimmediately before the next rinse cycle.


9/31

en

9

Filling the rinse-aidcontainer

The purpose of a rinse-aid is to preventthe formation of water marks on tablewareand utensils, and to ensure that glasses

are clean and sparkling. The rinse-aid isconsumed during the washing process.

Fold back the lid on the rinse-aidcontainer 29 .

To open the lid, press the mark (1 ) onthe rinse-aid lid and simultaneously lift

the lid off the lug (2 ).

1

2

Pour the rinse-aid into the filler holeuntil the level indicator turns dark.

Close the lid, ensuring that you hear itsnap closed.

Use only rinse aid for domesticdishwashers. Spilt rinse aid may result inexcessive foam formation in the next rinsecycle. Therefore, remove any spilt rinseaid with a cloth.

Adjusting the amount ofrinse-aid

The amount of rinse-aid added to thewater can be varied by adjusting thestepless control. The rinse-aid control hasbeen set to 4 in the factory.

Do not alter the setting of the rinse-aidcontrol unless streaks (turn knob towards) or water marks (turn knob towards +)are left on the dishes.

29

rinseaid control

Low rinse-aid indicator

As long as the rinse-aid refill indicator onthe panel 8 (on applicable models) or

dispenser 29 has not illuminated, there is

sufficient rinse-aid in the dishwasher.

LOW RINSE-AID indicator


10/31

en

10

Switching the rinse-aidindicator on or off

You can switch the rinse-aid indicator 8

on or off. This function can be changed asfollows:

Close the door.Hold down programme button C and

press main switch 1 until the digital

display illuminates, then release thebuttons.On the digital display 3 is

indicated (rinse-aid indicator on).

By pressing the programme button C

you can switch the rinse-aid indicatoroff or on .

Switch off the main switch 1 ; thechosen setting has now been stored.

Note

Do not switch off the rinse-aidindicator unless you are usingdetergent products with anintegrated rinse-aid!

Unsuitable dishes

You should not clean thefollowing items in yourdishwasher:

Cutlery and dishes made of wood. Theywill leach out and become unsightly; theutilised adhesives are also not suitablefor the dishwasher temperatures.

Delicate dcor glasses, craft dishes andvases, special antique or irreplaceabledishes. These dcor items are notdishwasher-safe.

Plastic parts, copper and tin dishes

sensitive to hot water are not suitableeither. Overglazed patterns, aluminiumand silver parts tend to becomediscoloured and fade during the rinsingcycle. Even some types of glass (e.g.crystal glass objects) may become cloudyafter many rinse cycles. Completelyabsorbent materials, such as sponges andcloths must not be cleaned in thedishwasher either.

Recommendation:

In future buy only dishes which areidentified as dishwasher-safe.

Note

Dishes which are soiled withash, wax, lubricating grease orink must not be cleaned in thedishwasher.


11/31

en

11

Damage to glassware and otherdishes

Possible causes:

type of glass or manufacturing process

chemical composition of detergent

water temperature and duration ofdishwasher programme.

Suggested remedy:

Use glassware or porcelain dishes thathave been marked dishwasherproofby the manufacturer.

Use a mild detergent that is describedas kind to dishes. If necessary, seekfurther information from detergent

manufacturers.Select a programme with as low atemperature and as short a duration aspossible.

To prevent damage, take glass andcutlery out of the dishwasher as soonas possible after the programme hasended.

Washing contents of UPPER

RACK only* not on all models

If you only have a small number of dishesto wash, put them all into the upper rackand press the UPPER RACK button. Thissaves energy and water. If you select theUPPER RACK function, the lower rackmust be empty. Add a reduced amount ofdetergent compared to that which isrecommended for a full load.

Arranging crockery, glasses,etc. in the dishwasher

Loading the dishwasherScrape off any large amounts ofleft-over food. It is not necessary to

rinse the dishes under running water.Place objects in the dishwasher in sucha way that items such as cups, glasses,

pots/pans, etc. are stood upsidedown,

curved items, or those withrecesses, should be at a slant sothat water can run off,

they are stacked securely andcannot tip over,

they do not prevent the spray armsfrom rotating while washing takesplace.

Very small items should not be washed inthe dishwasher as they could easily fall outof the baskets.

Removing the dishesTo prevent water dripping from the top

basket onto the dishes in the lower basket,we recommend that you empty the lowerbasket first and then the top basket.

Cups and glassesUpper basket 20

*on applicable models


12/31

en

12

Pots and pans

Lower basket 27

Cutlery

Cutlery should be placed in thedishwasher always unsorted and with theeating surface pointing downwards. Thespray jet is then better able to reach theindividual parts.

To prevent injuries, place long, pointedaccessories and knives on the tagre(some models) or on the knife shelf(available as an accessory).

Folding spikes *


To improve stacking of pots and pans, thespikes can be folded down.

Shelf *

* not on all models

Lean tall glasses and those with longstems against the shelf not against otheritems to be washed.

Long items, serving cutlery, salad serversor knives should be placed on the shelf sothat they do not obstruct the rotation of thespray arms. The shelf can be folded backwhen not required for use.

Small accessories holder*

* some models

Light-weight plastic accessories, e.g. cups,

lids, etc. can be held securely in the smallaccessories holder.


13/31

en

13

Adjusting position of basket *

* not on all models

86cm

81cm

max.

30/*25cm

max.

20/*25cm

max.

34/*29cm

max.

20/*25cm

If required, the height of the top basket canbe adjusted in order to create more spacefor large utensils either in the top or bottombasket.

Select one of the two following proceduresaccording to the design of the top basketfor your appliance model:

Top basket with upperand lower roller pairs

Pull out the top basket.

Remove the top basket and re-attach itto the upper or lower rollers.

Top basket with side levers(Rackmatic)

Pull out the top basket.

To lower the basket, press insuccession the two levers on the leftand right sides of the basket. Always

take hold of the side of the basket onthe upper edge, otherwise the basketwill not drop smoothly (and maydamage the utensils).


14/31

en

14

To raise the basket, take hold of thebasket on the upper edge and pullupwards.

Before you re-insert the basket, ensurethat it is at the same height on bothsides. Otherwise, the appliance doorcannot be closed and the upper sprayarm will not connect to the water circuit.

Baking sheet spray head *

* some models

You can clean large baking sheets orgrilles with the baking sheet spray head.To do this, remove the top basket andinsert the spray head as illustrated in the

diagram.

To ensure that the spray jet can reach allparts, arrange the baking sheets as

illustrated(max. 4 baking sheets and 2 grilles).


15/31

en

15

Detergents

Information about detergents

You can use any brand of liquid or powderdetergent, as well as tablets, that havebeen specifically designed for use in

domestic dishwashers. (Do not use normalwashing-up liquid!)

Nowadays there are three types ofdishwasher detergent available:1. those containing phosphates and chlorine,2. those containing phosphates but no chlorine,3. those containing neither phosphates

nor chlorine.

When a phosphate-free detergent is usedin conjunction with hard water, there is agreater possibility that white marks will beleft behind on crockery and glasses, etc.These can be avoided by pouring anincreased amount of detergent into thedispenser.

Chlorine-free detergents have a reducedbleaching effect. This can mean that teastains are not completely removed orplastic items become discoloured.

This can be resolved by:

selecting a higher temperatureprogramme, or

increasing the amount of detergent,or

using a detergent that containschlorine.

Check the label on the detergentpackaging to determine whether aparticular product is suitable for use withsilverware.

If you have any further questions, werecommend that you contact the customeradvice departments of the variousdetergent manufacturers.

Detergent compartment withmeasuring marks

The side of the detergent compartment ismarked with lines to help you determinehow much powder to add.The capacity of the detergent container is15 ml up to the bottom line and 25 ml up tothe middle line. When the compartment isfull it contains 40 ml.

40 ml

25 ml

15 ml

Important

If the lid on the detergent com-partment is closed, press therelease lever to open the flap.

Adding detergent

Tip detergent powder into thecorresponding compartment 30 .

Please observe the manufacturersinstructions printed on the detergentpackaging when determining thecorrect dosage.

ImportantDue to the different solvency properties ofthe detergent tablets supplied by variousmanufacturers, the cleaning efficiency ofthe detergent may not be fully utilised byshort programmes. It is recommended touse washing powder for theseprogrammes.

When you select the INTENSIVEprogramme, tip an extra 1015 ml of

detergent onto the inside surface of thedoor.


16/31

en

16

Reduce costs!

If you are using the upper rackonly, or if your dishes are onlymoderately dirty, it will normally

suffice to employ a reducedamount of detergent thanotherwise recommended.

Close the lid on the detergentcompartment.Press down the lid (1) until it clicksshut (2).

If you are using detergent in tablet form,read the manufacturersrecommendations on the packaging in

order todetermine where the tablets should beplaced inside the dishwasher (e.g. incutlery basket, detergent compartment,etc.).Make sure that the lid on the detergentcompartment is closed, even if you areusing tablets.

auto 3in1

The use of so-called combined detergentproducts may make the use of rinse aidand/or salt unnecessary.

There are currently several types of

combined detergent products available.3in1:They contain detergent, rinse aidandsalt function.

2in1:They contain detergent and rinseaid or salt function.

>>>Always check the type of detergentor combined product which youare using!

Always follow the operating instructionsor the information on the packaging.

The rinse programme is automaticallyadjusted in order to obtain the bestpossible rinsing and drying result.

Observe the following importantinformation if using combined cleaningproducts:

Regeneration salt is not required up to

a water hardness of 21dH (37fH,26Clarke, 3.7 mmol/l) only. No othersettings on the appliance are required.

Salt is still required if the waterhardness is above21dH (37fH,26Clarke, 3.7 mmol/l). Fill the saltdispenser with salt 24 and select

setting 6 on the water softening system.

If in doubt, please contact the detergentmanufacturer, especially if:

the utensils are very wet at the endof the programme.

limescale forms.


17/31

en

17

Note

Optimum rinsing and drying results can beobtained by using standard detergents inconjunction with separate application ofsalt and rinse aid.

Observance of the operating instructionsor information on the packaging of thecombined detergents determines theireffectiveness.

Note

Even if the rinse aid and/or salt refillindicator is lit, the rinse programme runs

correctly when 3in1 products are used.

If the rinse aid refill indicator 8 or salt

refill 7 indicator is defective and you

would like to switch it off, proceed asfollows:

Switching the rinse aid refillindicator off and on

You can switch the rinse aid refill indicator8 on or off. This function can be

changed as follows.

Close the door.

Hold down the programme button C

and press the main switch 1 until thedigital display lights up, then release thebuttons.

3 is indicated on the digital display

(rinse aid refill indicator on).

By pressing the programme button

C , you can switch off or switch

on the rinse aid indicator.

Switch off the main switch 1 ;

the setting is saved.

Switching the salt refillindicator / water softeningsystem off and on

Close the door.

Hold down the programme button B

and switch on the main switch 1 ,then release the buttons.

The illuminated button B and the

factory-set value on the digital

display flash.

To change the setting: press the

programme button B .

Each time the button is pressed, the set

value increases by one; when the valueis reached, the display jumps back

to (the salt refill indicator / water

softening system has been switchedoff).

Switch off the main switch 1 .The set value is stored within thedevice.

Approx. 4 litres of water are required to

regenerate the water softening system.As a result, the water consumption perrinse cycle increases by 0 to maximum4 litres depending on the water hardnesssetting.

Note

If you use the detergent and rinse aidseparately or switch from combined

detergents to standard cleaning products,ensure that the rinse aid refill indicator hasbeen switched on and the water softeningsystem has been set to the correct waterhardness.


18/31

en

18

Programme overview

This overview lists the max. possible number of programmes. The programmes supplied with yourappliance are indicated on the fascia.

Type of crockery

e.g.china,pots/pans,cutlery,glasses,etc.

Type of foodremains

Amount offood remains

Condition offood remains

Washprogramme

Programmesequence

Non-

delicate

Soups, casseroles,sauces, potatoes,pasta, rice, eggs,roast or fried food

Soups, potatoes,pasta, rice, eggs,roast or fried food

Coffee, cakes,milk, sausage,cold drinks,

salads

a lot very little

stuck on hard

Normal65

Intensive70

Eco50

Quick45

Pre-rinse

Rinse-aid70

Drying

Drying

Rinse-aid70 Drying

Main rinse Main rinse

Rinse-aid55

Wash45

Rinse-aid65

Wash50

Rinse off ifthe disheshave beenstacked for

severaldays in thedishwasher

prior to

washing.

Pre-rinse

Mixed DelicateMixed

Gentle40

Pre-rinse

Wash40

Main rinse

Rinse-aid55

Drying

a little

loosely attached

Secondrinse

First rinse

Wash65

Pre-rinse Pre-rinse

Thirdrinse

Pre-rinse50

Wash70

First rinse

Secondrinse

Programme selection

The most appropriate programme can beidentified by comparing the type ofcrockery, cutlery, etc., as well as theamount and condition of food remains,with the details contained in theprogramme overview.

You will find the appropriate programmeinformation in the introduction.


19/31

en

19

Washing dishes

Reduce costs!

If only a small number of

dishes have been loaded intothe dishwasher, selecting aprogramme that operates atthe next lowest temperaturewill usually suffice.

Programme data

The programme specifications can befound in the summary of instructions.Programme specifications refer to normal

conditions. Greater deviations may occurdue to:

different amounts of dishes

temperature of mains water supply

pressure of mains water supply

ambient temperature

fluctuations in mains voltage

machine-related factors (e.g.temperature, water volume, ...).

Energy and water consumption is reducedby up to 1/4 when dishes are washed inthe upper basket only.

Water consumption values are based on awater hardness setting of 4.

Aqua sensor *


The Aqua sensor is an optical measuringdevice which measures the turbidity of the

rinsing water. A light barrier can detectdissolved food remnants in the water, e.g.egg, fat and oats.

The Aqua sensor is used according tothe programme. When the Aqua sensoris active, clean rinsing water may betransferred into the next rinsing bathand/or the temperature adjusted. If theturbidity is greater, the water is drainedand is replaced with fresh water. In this

way the water consumption is reduced byapprox. 4 litres for utensils which are lessdirty.

Switching the dishwasher ON

Turn on the tap.

Set main switch 1 to ON.

Indicators light up according to the lastprogramme that was selected.This same programme will run again ifno other programme button 6 ispressed.

For appliances with top basket feature:If only the top basket is loaded, pressthe top-basket button 5 .

The numerical display 3 shows theexpected duration of the programme.

The programme starts automatically.

Remaining running time displayWhen the appliance has started, theexpected programme running time isdisplayed. The programmed running timeis affected by the water temperature, thenumber of dishes, as well as the degreeof soiling. If these conditions are changed,the running time (depending on theselected programme) can vary greatly.As the effect is not detected until a

programme is running, the time maybe longer or shorter than expected.

Time delay *

*on applicable modelsYou can delay the start of the programmein 1-hour steps up to 19 hours.

Switch on the appliance.

Press the timer programming button4 until the digital display 3 jumps

to .

Keep pressing the timer programmingbutton until the required time isdisplayed.

To delete the timer programming,keep pressing the button until

is displayed.

You can change your programmeselection at any time until the

programme starts.


20/31

en

20

End of programme

The programme has ended when a figureappears in the numerical display 3 .

Switching the dishwasher OFF

Several minutes after the programme hasended:

Set the main switch 1 to OFF.

Turn the water tap off.(Does not apply when Aqua-Stop unithas been fitted)

Remove dishes, etc. when they havecooled down.

Interrupting the programme

Set main switch 1 to OFF.

Indicator lights extinguish. Theprogramme is retained in thedishwasher memory.

If the hot water was switched ON or theappliance has already heated up and thenthe appliance door opened, leave the doorajar for several minutes and then close.Otherwise, the appliance door may fly

open due to expansion.In order to continue with the storedprogramme, set the main switch to ONagain.

Cancel programme (Reset)

Only when the master switch is ON.

Press the A and C buttons

simultaneously, and hold them pressedfor approx. 3 seconds.The numerical display shows .

Close the door.

The programme continues for approx.1 min.

When it has ended, set the main switch1 to OFF.

Close the detergent compartment 30 .

To restart the dishwasher, set main switch1 to ON again and select desired

programme.

Changing the programme

It is possible to change the programmewithin 2 minutes after you have switchedthe dishwasher on.

Should it be necessary to change theprogramme after this period, the

programme cycle that has already beenbegun (e.g. washing) will be completedfirst of all.

The new remaining time displayed is thesum of the remaining time from thepreceding programme cycle and theremaining time attributable to the newprogramme that has been selected.

Intensive drying

If the Intensive drying function isactivated, the temperature of the final rinseis increased in all programmes and youwill therefore receive an improved dryingresult. (Note the higher temperature maynot be suitable for fragile utensils.)

Hold down the programme button A

and switch on the main switch.

Release both buttons.

The digital display 3 flashes (on)or (off).

To change the setting, press the

programme button A .

Switch off the main switch 1 ;

the setting is stored.


21/31

en

21

Maintenance and care

You can help prevent faults by checkingand maintaining your appliance regularly.This will save time and reduce problems.Therefore you should occasionally

examine the inside of your dishwasher.Overall condition of theappliance

Check the rinsing compartment for greaseand limescale deposits.If you find any deposits:

Fill the detergent dispenser withdetergent. Start the empty appliancewith the programme which has the

highest rinsing temperature.Clean the door seal:

Wipe the door seal regularly witha damp cloth and remove any deposits.

Special dishwasher salt

Check the LOW SALT indicator 7 .

Top up with salt, if required.

Rinse-aid

Check the LOW RINSE-AID indicator8 on the front panel or the level

indicator on the rinse-aid container29 . Top up with rinse-aid, if required.

Filters

The filters 25 prevent larger remnants of

food or other objects from getting insidethe pump. This residue can occasionallyclog up the filters.

The filter system consists of a filtercylinder, a flat fine filter and, depending onthe model, a microfilter (*).

Inspect the filters for obstructions everytime the dishwasher has been used.

By unscrewing the filter cylinder, youcan remove the filter system. Removeany food remnants and clean the filtersunder running water.

Reassembly:Insert the filter system and screw downwith the filter cylinder.


22/31

en

22

Spray arms

Lime and remnants of food in the washingwater can block the nozzles in the sprayarms 22 and 23 and the arm

mountings .

Inspect the nozzles in the spray armsfor blocked holes due to remnants offood.

If necessary, pull the lower arm 23

upwards and lift it off.

Unscrew the upper spray arm 22 .

Clean both spray arms under runningwater.

01

23

Refit the spray arms. Ensure that thelower arm has locked into place and theupper one is screwed tight.

Pump *

*on applicable modelsLarger remnants of food that have notbeen trapped by the filters and have beenleft in the water can cause a blockage inthe pump. The water is no longer pumpedout of the dishwasher and it can be seencovering the filter.Proceed as follows:

Ladle out as much water as possible.

Remove the filters 25 .

Undo the screw in the cover (Torx T 20)and remove the cover.

Inspect the inside and remove anyobstructions that you find.

Re-insert the cover and screw down.

Re-insert the filters and screw down.

Torx T20

2

1


23/31

en

23

Fault finding

Resolving minor problemsyourself

Experience has shown that you canresolve most problems that arise duringnormal daily usage yourself, withouthaving to call out a service engineer. Notonly does this save costs, but it alsomeans that the appliance is available foruse again that much sooner. The followinglist of common occurrences and theirremedies should help you identify thecauses of most problems.

Problems ...

... when the applianceis switched on

The appliance does not start.

The mains fuse has tripped.

The appliance plug has not beeninserted.

The appliance door has not been

shut properly.The tap has not been turned on.

The filter on the water supply hoseis blocked.Switch off the appliance and pullout the mains plug. Turn off thetap. Then clean the filter which issituated at the connection of thesupply hose. Finally, restore thepower, turn on the tap and switch

on the appliance.

Warning

Remember:The appliance may be repairedby a technician only. Improperrepairs may cause

considerable damage and/orinjure the user.

... with the appliance itself

Lower spray arm rotates withdifficulty

Spray arm is blocked by smallitems or food remains.

Lid in detergent compartment

cannot be closedDetergent compartment has beenoverfilled.

Mechanism is clogged withremnants of detergent.Indicator lamps do not extinguishafter washing has finished.

Indicator lamps do not extinguishafter washing has finished

Main switch is still set to ON.

Remnants of detergent stuck insidedispenser

Compartment was damp when itwas filled up with detergent.Compartment must be dry beforedetergent is added.

Refill display does not light up.

Rinse aid refill indicator switchedoff. (see auto 3in1 chapter)

Salt refill indicator switched off.(see auto 3in1 chapter)


24/31

en

24

Water remains inside applianceafter programme has ended

Blockage or kink in drainage hose.

Pump is jammed.

Filters are blocked.

The programme is still running.Wait for the programme to end(numerical display will indicate 0).

Perform Reset function.

... during washing

Unusual amount of foam is created

Normal washing up liquid hasbeen poured into the rinse-aidcontainer.

Remove any spilled rinse aid witha cloth as it could otherwise leadto excessive foaming during thenext washing cycle.

Appliance stops suddenly whilewashing is taking place

Cut in electricity supply toappliance.

Water supply has beeninterrupted.

Knocking sound can be heardwhile washing is taking place

A spray arm is knocking againstthe dishes inside the appliance.

Rattling sound can be heard whilewashing is taking place

Crockery has not been stackedproperly inside the appliance.

Knocking sound coming from inletvalves

This is caused by the way thewater pipes have been laid and ithas no effect upon the way theappliance functions. There is noremedy for this.

... with the dishes, cutlery, etc.

Remnants of food are stuck to thedishes, cutlery, etc.

Dishwasher was not loadedproperly. Jets of water could notreach all parts of the dishes, etc.

Too many items in the rack.

Items in the rack were touchingeach other.

Not enough detergent was addedto dispenser.

Selected wash programme wasnot intensive enough.

Rotation of spray arm wasobstructed by dish, etc.

Nozzles in spray arm are blockedby remnants of food.

Filters are blocked.

Filters have been incorrectly fitted.

Waste-water pump is jammed.

Plastic items are discoloured

Not enough detergent was addedto dispenser.

White stains are left on crockery,glasses have a milky appearance

Not enough detergent was addedto input compartment.

Amount of rinse-aid was set toolow.

Although water is quite hard, nosalt has been put in appliance.

Water softener was set too low.

Lid on salt container is not

screwed tight.If you used a phosphate-freedetergent, try a detergentcontaining phosphates andcompare results.


25/31

en

25

Dishes, cutlery, etc. have not beendried

Selected programme did notinclude drying function.


Items were removed fromdishwasher too soon.

Glasses have a dull appearance


Tea stains or traces of lipstick havenot been completely removed

Detergent does not have asufficient bleaching effect.

Washing temperature was set toolow.

Traces of rust on cutlery

Cutlery is not sufficiently rustproof.

Salt content in washing water istoo high.

Lid on salt container is notscrewed tight.

Too much salt was spilt while

filling container.Glasses become clouded anddiscoloured; coating cannot bewiped off

Unsuitable detergent was used.

Glasses are not dishwasher-proof.

Smears left behind on glasses andcutlery; glasses have acquired ametallic appearance

Amount of rinse-aid set too high.

Customer Service

Please call your local service agent, if youare not able to resolve any problemyourself. The name of your nearest serviceagent is shown in the Customer Service

address list. When you call, please providedetails of the model number (1) and theproduction (FD) number (2) which areshown on the nameplate 31 on the

appliance door.

FD

1

2

Warning

Please note that a visit by thecustomer service technician inthe event of a fault or one ofthe problems previouslydiscussed is not free of chargeeven during the warrantyperiod.


26/31

en

26

Information

Notes on comparison tests

You will find details of the conditions forthe comparison tests on the additionalNotes on comparison tests sheet. The

consumption values for the relevantprogrammes are given in the introduction.

General

Built-under and integrated applianceswhich are subsequently installed asfree-standing appliances must besecured to prevent them from fallingover, e.g. by screwing them to the wallor by installing them under a continuous

worktop which is screwed to theadjoining units.

For Swiss version only:The appliance can be installed withoutdifficulty between wooden and plasticwalls in a kitchen range. If the applianceis not connected via a plug, theinstallation side must feature an all-poledisconnector with a contact gap of atleast 3 mm in order to satisfy the

relevant safety regulations.

Installation

The dishwasher must be connected bya qualified technician to ensure correctoperation. The specifications for supply,drainage and connected load must fulfil

the required criteria as stated in thefollowing paragraphs or in the installationinstructions.

Install the appliance in the followingsequence:

Check the delivery Install the appliance Connect the waste water Connect the fresh water

Connect the power supplyDelivery

Your dishwasher was checked at thefactory to ensure that it was in perfectworking order. This may have left somesmall water stains in the dishwasher.These will disappear after the first rinsecycle.

Installation

The required installation dimensions canbe found in the installation instructions.Using the height-adjustable feet, adjust theappliance until it is level. Ensure that theappliance is standing firmly.

Waste water connection

See the installation instructions for therequired connection steps. If required,attach a siphon with drainage spigot.Using the enclosed parts, connect thewaste water hose to the drainage spigotof the siphon.Ensure that the drainage hose is notkinked, crushed or twisted (ensure thatthere is no sealing cover which preventsthe waster water from flowing away!).


27/31

en

27

Fresh water connection

Using the enclosed parts, connect thefresh water connection to the tapaccording to the installation instructions.Ensure that the fresh water connection isnot kinked, crushed or twisted.

When replacing the appliance, alwaysconnect a new water supply hose to thewater supply. The old supply hose mustnot be re-used.

Water pressure:

Minimum 0,05 MPa (0,5 bar) maximum1 MPa (10 bar).If the water pressure is higher, install apressure reducing valve.

Flow rate:Minimum of 10 litres per minute.

Water temperature:

We recommend that you use cold water.If you do use hot water, the temperatureshould not exceed 60 C.

Electrical connection

Connect the appliance only to 230 V

alternating current via a correctly installedsocket with protective conductor.See rating plate for required fusing 31 .

The socket must be attached near thedishwasher and be freely accessible.The connection may be modified by anelectrician only.

Use only a residual-current-operated

circuit-breaker which features thesymbol. Only this circuit breaker

guarantees compliance with the currentlyvalid regulations.

Removing the appliance

It is essential, when removing theappliance, to observe the followingsequence: First, disconnect the appliancefrom the power supply.Pull out the mains plug.

Turn off the water supply.Disconnect the waste water and freshwater connections.Loosen the fastening screws under theworktop. If fitted, remove the base panel.Pull out the appliance, carefully pulling thehose behind.

Transporting the dishwasher

Drain water from the dishwasher. Secure

all loose parts. The appliance should onlybe transported in an upright position.

If the appliance is not kept uprightduring transport, any water left insidemay seep into the control module andcause subsequent errors withprogramme functions.

The appliance must be drained in thefollowing sequence:

Turn on the tap.

Close the door.

Set main switch to ON.

Select the B programme. The

programme duration in minutes isshown in the numerical display.

Wait for approximately 4 minutes.

Terminate the programme by

pressing A and C

simultaneously.

The time display changes to .

Wait a further minute and thenswitch the appliance off.

Turn off the tap.


28/31

en

28

Protection from freezingtemperatures

If the appliance is installed in a locationwhere there is a risk of freezingtemperatures (e.g. in a holiday home), allwater must be completely drained out ofthe interior (see Transporting thedishwasher).

Turn OFF the tap, disconnect the supplyhose and allow to drain.


29/31

en

29

en Subjekt to modification


30/31


31/31

SiemensElectrogerte GmbHCarlWeryStrae 3481739 Mnchen

To contact us directly, use the tel. no or fax no. in theenclosed customer service list.

upustvo mašina upustvo mašina za suđe

Documents