treso muzzleloader accessories catalog 2013

Choice of the Discriminating Shooter...

Treso, llc135 Country Center Drive

Suite F, #251Pagosa Springs, CO 81147

Phone: 970-731-2295Fax: 970-731-5503

Email: [email protected] back under the ownership and management of the original owner, Don C. Miner

CATALOG 2013CATALOG 2013CATALOG 2013

75-03 75-01

Description Item No.

Powder Flask (w/30 gr. spout) .........................................11-75-03Powder Flask (w/pouring spout) ......................................11-75-04Powder Flask (w/ internal safety valve)...........................11-75-08Powder Flask (w/external safety valve)...........................11-75-07Half Pint Powder Flask (w/30 gr. spout) ..........................11-75-02Half Pint Powder Flask (w/pouring spout) ......................11-75-01Half Pint Powder Flask (w/internal safety valve).............11-75-06Half Pint Powder Flask (w/external safety valve)............11-75-05

POWDER FLASKThe body of this cylindrical brass powder flask is 5” long, 1 3/8” in diameter and holds approximately 3.2 oz. of black powder. The Half Pint flask is 2 3/4” long. The top screws off for easy refilling. With its flat bottom, the flask will stand upright on your shooting bench. Several variations are available with TRESO’s push button “Fast Flow Valves” and spout combinations.

TRESO MUZZLELOADING ACCESSORIES

Pagosa Springs, Colorado -- home of TRESO, LLC -- got its name from the naturally occuring geothermal spring that emerges near the center of town on the banks of the San Juan River. The spring discharges 150° F water at a rate of about 700 gallons per minute. The Ute Indians were one of several American Indian tribes which once claimed ownership of the Pagosa hot springs. They called the springs “pah gosah,” a term which has been variously translated in recent years as meaning “boiling water” or “healing water.” However, a Ute elder once suggested that a more accurate translation would be “water that has a strong smell.” The strong smell of the hot springs derives from its remarkably high mineral content, which many believe gives the water its naturally therapeutic value. The Native Americans of the Four Corners area staged numerous wars and skirmishes over the ownership of the springs, so highly did regard the importance of its healing powers.


Deluxe Adjustable Powder Measure 0-120 grs. ..............................11-01-120Deluxe Adjustabe Powder Measure 40-200 grs. .............................11-01-200

DELUXE ADJUSTABLE POWDER MEASUREThis measure features a swing-over pouring spout for spill free pouring. It is made of brass with five grain graduations. A nicely knurled steel screw provides positive locking adjustment at any position.


Adjustable Powder Measure 0-120 grs .........................................11-02-120Adjustable Powder Measure 40-200 grs .......................................11-02-200Adjustable Powder Measure 150-300 grs. ....................................11-02-300

ADJUSTABLE POWDER MEASUREThis measure is the same as the Deluxe black powder measure but does not have the swing over spout.


Adjustable Measure with Funnel................................................. 11-03-120

ADJUSTABLE MEASUREWITH FUNNELHouse of MusketsThis adjustable powder measurecombines the TRESO 11-02-120measure with a swivel funnel unit. Makespouring powder into the muzzle of amuzzleloader easy, with fewer spilling problems.Funnel is made of spun brass.

page 2


CAUTION: ALL TRESO FLASK SPOUTS AND POWDER MEASURES ARE TO BE USED ONLY FOR BLACK POWDER OR PYRODEX. The indicated charges are at best only approximate due to the different powder grain size and other variables. Black powder and Pyrodex are approxi-mately equivalent by volume only -- not by weight.

FLASK SPOUTThese replacement flask spouts will fit the TRESO flask and powdervalves and most Italian made powder flasks, except the baby size .31caliber flasks (see special size below). Spouts are made of brass and can be reduced in length to vary powder charge.

.oN kluB.oN metInoitpircseD

...... 12-04-010...... 12-04-015...... 12-04-020...... 12-04-025...... 12-04-030...... 12-04-035...... 12-04-040

...... 12-04-055

...... 12-04-050 ...... 12-04-045

...... 12-04-060

...... 12-04-065

...... 12-04-070

...... 12-04-080

...... 12-04-085 ...... 12-04-090 ...... 12-04-095 ...... 12-04-100...... 12-04-110

Pour Only Spout Adapter. ...................... 11-04-300 ...... 12-04-300

...... 12-04-075

............................... 11-04-010............................... 11-04-015............................... 11-04-020............................... 11-04-025............................... 11-04-030............................... 11-04-035............................... 11-04-040

............................... 11-04-055

............................... 11-04-050

............................... 11-04-045

............................... 11-04-060

............................... 11-04-065

............................... 11-04-070

............................... 11-04-080

............................... 11-04-085............................... 11-04-090............................... 11-04-095............................... 11-04-100............................... 11-04-110............................... 11-04-125............................... 11-04-150............................... 11-04-200

............................... 11-04-075

10 grain Flask Spout15 grain Flask Spout20 grain Flask Spout25 grain Flask Spout30 grain Flask Spout35 grain flask Spout40 grain Flask Spout

55 grain Flask Spout50 grain Flask Spout45 grain Flask Spout

60 grain Flask Spout65 grain Flask Spout70 grain Flask Spout

80 grain Flask Spout85 grain Flask Spout90 grain Flask Spout95 grain Flask Spout

100 grain Flask Spout110 grain Flask Spout125 grain Flask Spout150 grain Flask Spout200 grain Flask Spout

75 grain Flask Spout

(see page 4)


d

n

.o

80 grain Powder Measure .......................1 1-71-080......12-71-080

11-70 Series

11-71 Series

11-72 Series

FIXED POWDER MEASUREThis fixed measure is made from brass. Measures have a nicely turnebase with a hole for tying by a thong to a horn or hunting bag. The #70series have a 3/8" diameter, the #71 series have a ½" diameter and the#72 series have a 9/16" diameter. These measures can be reduced ilength for in-between charges.

N kluB.oN metInoitpircseD

20 grain Powder Measure .......................1 1-70-020 ......12-70-02030 grain Powder Measure .......................1 1-70-030 ......12-70-03040 grain Powder Measure .......................1 1-70-040 ......12-70-040

50 grain Powder Measure .......................1 1-71-050 ......12-71-05060 grain Powder Measure .......................1 1-71-060 ......12-71-06075 grain Powder Measure .......................1 1-71-075 ......12-71-075

90 grain Powder Measure .......................1 1-71-090 ......12-71-090100 grain Powder Measure .....................1 1-71-100 ......12-71-100110 grain Powder Measure .....................1 1-71-110125 grain Powder Measure .....................1 1-71-125150 grain Powder Measure .....................1 1-71-150

75 grain Powder Measure .......................1 1-72-075 ......12-72-075100 grain Powder Measure .....................1 1-72-100 ......12-72-100125 grain Powder Measure .....................1 1-72-125150 grain Powder Measure .....................1 1-72-150200 grain Powder Measure .....................1 1-72-200

.oN metInoitpircseD

Flintlock Pan Primer .......................................................1 1-06-34Magnum Flintlock Pan Primer .......................................1 1-06-36

FLINTLOCK PAN PRIMERThese flintlock pan primers are operated by a simple downward push intothe pan. Both will dispense approximately 3 grains of 4fg priming powderin the pan. These pan primers are made of brass with a stainless steelspring. A lanyard hole is provided in a nicely turned base. The primingmechanism is in a knurled, threaded housing that is removable for easyfilling . The standard primer holds approximately 80 grains of powderand the magnum primer holds about 230 grains.

06-36

06-34

FLINTLOCKPRIMING VALVESThe TRESO flintlock pan priming valve operates the same as in our Pan Primer. It is intended to be installed in a priming horn or other suit-able priming powder container (some have used a brass cartridge case). It is designed for 4fg black powder only. Available in two dispensing sizes, 1 and 3 grain. The larger valve has an overall dimension of 3/8” x 1 1/8” long.

Description Item No. Bulk No.

Flintlock Priming Valve - 1 grain .............11-06-31 .........12-06-31Flintlock Priming Valve - 3 grain .............11-06-33 .........12-06-33

06-31

06-33

PAN PRIMING VALVEFOR COLT-STYLE FLASKThe TRESO pan priming valve for Colt flask operates the same as in our Pan Primer. It is threaded to fit Colt or baby size flasks. The valve is used by removing the flask valve spring, locking the flask valve open, and threading the priming valve into the spout hole. It is designed for 4fg black powder only and dispenses approximately 3 grains of powder.


Pan Priming Valve for Colt size Flask .......11-06-45 ..........12-06-45Pan Priming Valve for baby size Flask ......11-06-46 ..........12-06-46

.31 CALIBER “BABY FLASK” FLASK SPOUT


25 Grain .31 Caliber Flask Spout ............ 11-05-025 ...... 12-05-025

.oN metInoitpircseD

Free-Flow Flintlock Pan Primer .....................................1 1-06-38

FREE-FLOW FLINTLOCK PAN PRIMERTRESOThis free-flow pan primer dispenses a continues flow of 4fg powder whenthe side button is depressed. The primer holds approximately 135 grainsof powder. The head is removable for easy filling.


page 4


Powder Valve with Powder Can Cap ...........11-06-06 .........12-06-06

POWDER VALVE WITH POWDER CAN CAPThis is our Fast Flow powder valve fastened to a Goex Black Powder can cap. Screw this directly onto your black powder can and use it as a ready made flask; no more inconvenience of pouring powder from can to flask or horn.

SAFETY VALVE WITH POWDER CAN CAPThese are our Safety Valves fastened to Goex Black Powder can caps. Screw this directly onto your black powder can and use it as a ready made flask - no more inconvenience of pouring powder from can to flask or horn.

06-29(external)

06-26(internal)


Saftey Powder Valve (internal) with Powder Can Cap ............11-06-26 .........12-06-26Saftey Powder Valve (external) with Powder Can Cap ............11-06-29 .........12-06-29

NIPPLE CHARGERThis device deposits 4fg priming powder into the nipple cone for a surefire shot. To use, place on top of the nipple cone and push down, allowing the priming powder to flow into the nipple cone. Unlike other nipple charges this one is designed to work with either number 11 cap nipples or musket cap nipples. The top has a hole for a lanyard and will screw off for easy refilling.


Nipple Charger .................................................................11-06-40

SAFETY VALVESThese two valves are the same design as our Fast Flow powder valve. One has a nose designed to fit into a powder measure and the other is designed to fit the outside of a powder measure. These valves are made to work with our series #71 fixed powder measures, our 120 grain adjustable powder measure or other powder measures with a similar inside/outside diameter. To operate, place measure on the valve and open valve for a moment, then withdraw measure and it will be filled level with the top. Using this valve will prevent spillage and give more uniform powder measuring.

06-07(external)


Safety Powder Valve (internal) .............................11-06-05 ...........12-06-05Safety Powder Valve (external).............................11-06-07 ...........12-06-07Safety Powder Valve w/ bushing (internal) ..........11-06-25 ...........12-06-25Safety Powder Valve w/ bushing (external) .........11-06-28 ...........12-06-28

06-05(internal)

11-06-20 11-06-03 11-04-300

“FAST FLOW” POWDER VALVEThe “Fast Flow” powder valve was designed to provide a faster flow ofpowder and keep the physical size small. This valve, when in the openposition, has a straight-through 17/64" diameter hole for the fast flow ofpowder when hunting or participating in timed events. The body of thisfast-flow valve is actually smaller (9/16" diameter) than other valves re-sulting in a more aesthetically pleasing powder horn installation. Thevalves w ill accept standard flask spouts a nd our pouring adapter. Thevalve has a 3/8-24 thread for attachment to a powder horn or container.Use the TRESO valve bushing for a neat installation on a powder horn.The bushing has a 3/8-24 female thread and is meant to be epoxied intothe horn.


Powder Valve ..............................................11-06-03 ..........12-06-03Powder Valve w/ adapter ............................11-06-04 ..........12-06-04Powder Valve w/ bushing ...........................11-06-23 ..........12-06-23Powder Valve w/ bushing & adapter ..........11-06-24 ..........12-06-24Valve Bushing Only ....................................11-06-20 ..........12-06-20Pouring Adapter Only .................................11-04-300 ........12-04-300

.1



.32, .36 & .38 Caliber Short Starter .........11-08-32 .........12-08-32

.40 & .45 Caliber Short Starter ................11-08-45 .........12-08-45

.50 Caliber Short Starter ..........................11-08-50 .........12-08-50

.54 Caliber (and larger) Short Starter .......11-08-54 .........12-08-54

PARTS.32 caliber brass starter button (5/16 dia.) ........................12-08-5B.32 caliber brass long starter (5/16 dia.) ...........................12-08-5S.45 caliber brass button starter(3/8 dia.) ...........................12-08-6B.45 caliber brass long starter tip (3/8 dia.) .......................12-08-6T.45 caliber wood long starter (38 dia.) .............................12-08-6S.50 caliber brass button starter (7/16 dia.) ........................12-08-7B.50 caliber brass long starter tip (7/16 dia.) .....................12-08-7T.50 caliber wood long starter 7/16 dia.) ...........................12-08-7S.54 caliber brass starter button (1/2 dia.) ..........................12-08-8B.54 caliber brass long starter tip (1/2 dia.) .......................12-08-8T.54 caliber wood long starter (1/2 dia.) ............................12-08-8S Hardwood Ball (1 3/4 dia.) ..............................................99-024

SHORT STARTERS The TRESO short starter is considered the standard. The handle is a 1¾” diameter hardwood ball. The long starter is selected straight grain hickory wood with a brass tip to prevent splitting. The .32 caliber starter has a brass long starter. The button starter in the ball is solid brass and is 90° from the long starter making it convenient to hold in one hand while the other starts the ball or bullet in the muzzle of the barrel. Both button and long starter tip are cupped to center the starter over the bullet. Starters are dipped in hot linseed oil for a durable finish.


.45 Caliber Pistol Loader .........................11-10-45 .........12-10-45



PISTOL LOADERSThis pistol loader has a 1¾ inch diameter hardwood ball handle on a selected straight grain hickory wood rod 10¾ inches long. The hardwood ball also has a brass short starter. The jag tip is cross pinned to the rod. The jag has a spherically cupped end and is provided with a 10-32 thread to accept standard accessories.

POWDER HORNBASE PLUGThese brass powder hornbase plugs are designed to beinstalled in the base (largeend) of a powder horn. Thedecorative plug provides aremovable plug for easyfilling of the horn and a placeto tie one end of the hornlanyard. The plug comes witha brass bushing that ispermanently installed in the horn base. These plugs are available in twosizes. The large one is 1" in diameter with a 1/2”-20 thread; the smallone is 5/8” in diameter with a 3/8”-24 thread.


Powder Horn Base Plug - LARGE with bushing ..................1 1-07-07 ........ 12-07-07Powder Horn Base Plug - SMALL with bushing ..................1 1-07-08 ........ 12-07-08

POWDER HORNSPOUT & PLUGThe Powder Horn Spoutand Plug is a nicelyturned device that isinstalled in the pouringend of a powder horn.The spout has a generouspouring hole 3/8" indiameter for hurriedreloading in timedshooting events, hunting,etc. The plug for this spout has an “O” ring that creates a friction fit inthe spout holding it securely in place with a waterproof seal. A lanyardcan be tied to the groove provided on the plug to prevent its loss. Bothparts are made of brass.


Powder Horn Spout with Plug ................1 1-07-06 ........ 12-07-06


page 6

Patriot RamrodsThe TRESO “Patriot” ramrods are made of a space-age material that can literally be bent in a circle without breaking. The material is black giving the ramrod a traditional ebony wood look. All tips are securely fastened to the rods either by a pin or with threads.

Series 80 Replacement RamrodThe 80 series ramrod is a replacement ramrod for many of the popu-lar rifles by several manufacturers including Thompson Center Arms, Connecticut Valley Arms, Traditions and Lyman. The replacement rods come with a jag adapter on one end and a ball seating tip on the other end. Brass or steel is used that is appropriate with the original ramrod. The jag adapter is threaded 10-32 and the seater end is threaded 8-32 to accept standard TRESO accessories.

Description Length Item No.

T/C Scout .....................................................20 5/8” ............11-80-205White Mtn./Scout-T/C .................................21 5/8” ............11-80-215T/C Thunderhawk/Firehawk ........................24 5/8” ............11-80-245Deerstalker-Lyman ......................................24 3/4” ............11-80-246New Englander (Ryanite Rifle)-T/C ...........25” ..................11-80-250Renegade-T/C ..............................................26 5/8” ............11-80-265 New Englander (Rifle)-T/C ..........................27” ..................11-80-270CVA Hawken................................................27 1/2” ............11-80-274CVA Frontier Rifle ......................................27 3/4” ............11-80-276T/C Hawken ................................................28 5/8” ............11-80-285Trade Rifle-Lyman ......................................28 3/4” ............11-80-2861” Round Ball Barrels-T/C .........................30 5/8” ............11-80-305Penn Rifle & 15/16” RB Brl-T/C .................31 5/8” ............11-80-315CVA Mountain Rifle ....................................31 3/4” ............11-80-316Traditions Hawken ......................................31 7/8” ...........11-80-317Traditions Scout Rifle ..................................32 1/4” ............11-80-322Lyman Grt.Plains & GM Drop In Brls .........33” .................11-80-330

Series 84 Jag-TipRamrodSeries 84 ramrods are 3/8 inch in diameter and 48” long with a jag-tip of appropriate caliber on one end. These brass one piece ramrod tip and jag combinations have 10-32 threads to accept standard ramrod acces-sories. The jag has a spherically cupped end which will center ramrod over ball, thus preventing damage to the ball or barrel. It is intended that the user will cut the rod to the required length.


.45 caliber .............................................................................11-84-456

.50 caliber .............................................................................11-84-506

.54 caliber .............................................................................11-84-546

Series 82 Combination RamrodsThe 82 series rod is available in various lengths with a brass combo tip on one end and a standard 10-32 threaded brass tip on the other end. The combo tip consists of a rod tip with a bullet puller and a screw-on jag covering the bullet pulller.

Caliber Length Item No.

.50 cal. ......................................................21 1/4” ............11-82-035

.45 cal. ......................................................22” ..................11-82-094

.50 cal. ......................................................22” ..................11-82-095

.54 cal. ......................................................22” ..................11-82-096

.50 cal. ......................................................20 3/8” ............11-82-20550

.54 cal. ......................................................20 5/8” ............11-82-20554

.50 cal. ......................................................21 5/8” ............11-82-21550

.54 cal. ......................................................21 5/8” ............11-82-21554

.50 cal. ......................................................24 3/4” ............11-82-24650

.54 cal. ......................................................24 3/4” ............11-82-24654

.50 cal. ......................................................25” ..................11-82-25050

.54 cal. ......................................................25” ..................11-82-25054

.45 cal. ......................................................24” ..................11-82-254

.50 cal. ......................................................24” ..................11-82-255

.54 cal. ......................................................24” ..................11-82-256

.45 cal. ......................................................25” ..................11-82-334

.50 cal. ......................................................25” ..................11-82-335

.50 cal. ......................................................26 5/8” ............11-82-26550

.54 cal. ......................................................26 5/8” ............11-82-26554

.58 cal. ......................................................26 5/8” ............11-82-26558

.50 cal. ......................................................27” ..................11-82-27050

.54 cal. ......................................................27” ..................11-82-27054

.50 cal. ......................................................27 1/2” ............11-82-27450

.50 cal. ......................................................273/4” .............11-82-27650

.45 cal. ......................................................28 5/8” ............11-82-28545

.50 cal. ......................................................28 5/8” ............11-82-28550

.54 cal. ......................................................28 5/8” ............11-82-28554

.50 cal. ......................................................28 3/4” ............11-82-28650

.54 cal. ......................................................28 3/4” ............11-82-28654

.50 cal. ......................................................30 5/8” ............11-82-30550

.54 cal. ......................................................30 5/8” ............11-82-30554

.45 cal. ......................................................31 5/8” ............11-82-31545

.50 cal. ......................................................31 5/8” ............11-82-31550

.54 cal. ......................................................31 5/8” ............11-82-31554

.50 cal. ......................................................31 3/4” ............11-82-31650

.54 cal. ......................................................31 3/4” ............11-82-31654

.50 cal. ......................................................32 1/4” ............11-82-322

.50 cal. ......................................................33” ..................11-82-33050

.54 cal. ......................................................33” ..................11-82-33054

Series 85 Patriot Ramrods withCombination Jag-Bullet Puller TipsThe 85 Series Patriot rods are 3/8” diameter and come in lengths of 36” and 48”. This rod has the TRESO combination jag-bullet puller tips. The base for the combination ramrod tip has a built in steel lag screw for pulling bullets or retrieving lost patches. A jag or cover can be screwed on the base over the bullet puller. All parts are brass except for the steel bullet puller screw. These rods are intended to be cut to the required length by the user.

Description 36 inch 48 inch

.45 Caliber ................................................11-85-345 .......11-85-445

.50 caliber .................................................11-85-350 .......11-85-450

.54 caliber .................................................11-85-354 .......11-85-454Other calibers availbable on request.

HICKORY RAMRODSThese traditional ramrods are made from selected straight grained hickory and a ramrod tip. The TRESO tip is secured to the rod with a 1/16” cross pin. Ramrods are available in several configurations. The re-placement rods are made with T/C type tips (jag end has 10-32 threads - seater end has 8-32 threads).

Description 8-32 Thrd 10-32 Thrd

5/16” dia. 48” long w/brass tip ................11-90-508 .......11-90-5103/8” dia. 48” long w/brass tip ..................11-90-608 .......11-90-6103/8” dia. 36” long w/brass tip ..................11-89-608 .......11-89-6107/16” dia. 48” long w/brass tip ................11-90-708 .......11-90-7107/16” dia. 36” long w/ brass tip ...............11-89-708 .......11-89-7103/8” dia. 48” w/steel tip ...........................11-90-608S .....11-90-610S7/16” dia. 48” long w/steel tip .................11-90-708S .....11-90-710S

Hickory Replacement RamrodsCVA Mountain Rifle.........................................................11-90-100Uberti Santa Fe Hawken ..................................................11-90-195Lyman Great Plains Rifle ................................................. 11-90-50

Series 81 Blank With Traditional TipThe 86 series of rods have a standard 10-32 or 8-32 threaded brass tip on one end and are 36” and 48” long. These rods are intended to be cut to the required length by the user.


5/16” diameter 48” long with 10-32 threaded tip ................11-81-5405/16” diameter 48” long with 8-32 threaded tip ..................11-81-5483/8” diameter 36” long with 10-32 threads ..........................11-81-6303/8” diameter 36” long with 8-32 threaded tip ....................11-81-6383/8” diameter 48” long with 10-32 threads ..........................11-81-6403/8” diameter 48” long with 8-32 threaded tip ....................11-81-648

FIBERGLASS RAMRODSThese fiberglass ramrods are made from a smooth fiberglass rod and TRESO brass tips secured with epoxy and/or a 1/16” cross pin. Rods are 48” long and are available with tips having either a 8-32 or 10-32 thread. The 3/8” rod is dark brown in color and the 5/16” and 7/16” are black. The fiberglass ramrod is truly the only unbreakable ramrod avail-able. With its inherent stiffness, this rod is ideal for the hunting rifle. It will not swell like wood under wet conditions.

Description 8-32 thrd. 10-32 thrd.

5/16” dia. with Brass Tip .........................11-91-508 .......11-91-5103/8” dia. with Brass Tip ..........................11-91-608 .......11-91-6107/16” dia. with Brass Tip .........................11-91-708 .......11-91-710

.oN metInoitpircseD

5/16" Fiberglass Ramrod Blank ............................................. 99-04-53/8" Fiberglass Ramrod Blank ............................................... 99-04-6

FIBERGLASS RAMROD BLANKSFiberglass ramrod blanks are 48" long and are a dark black color.Fiberglass ramrods are the only truly "unbreakable" material forramrods.

page 7



5/16” x 48” Hickory ........................................................... 13-02-5483/8” x 36” Hickory .............................................................. 13-02-6363/8” x 48” Hickory .............................................................. 13-02-6487/16” x 36” Hickory ........................................................... 13-02-7367/16” x 48” Hickory ........................................................... 13-02-7481/2” x 48” Hickory ............................................................. 13-02-848

HICKORY RAMROD BLANKSHickory ramrod blanks are 36 and 48 inches long. We select the best quality from our stock for full-length ramrod blanks.


page 8

DURANGO GUN RODSDurango Gun Rods by TRESO are the best one-piece stainless steel loading and cleaning rods on the market. They are recognized by center-fire and black powder shooting enthusiasts everywhere as the very finest quality for their firearms. These rods have a hardwood handle of generous size to facilitate loading a tight bullet and the constant clean-ing required by the muzzle loading shooter. These black powder rods are available with either an 8-32 or 10-32 thread. The rods with 8-32 threads are 1/4 inch in diameter and the rods with 10-32 threads are 5/16 inch in diameter. The black powder handle is fixed to the rod allowing it to be used with a bullet puller. Each rod comes with a universal bore guide to eliminate wear on the muzzle.


Muzzleloading models without handle rotation:Vernon-10 34’ Rod (10-32 threads) .....................................11-92-09Creedmore-10 44’ Rod (10-32 threads) ...............................11-92-10Vernon 34’ Rod (8-32 threads) .............................................11-92-11Creedmore 44’ Rod (8-32 threads).......................................11-92-12Friendship 10’ Pistol Rod (8-32 threads) .............................11-92-13

Shotgun model without handle rotation or bore guide. Has an adapter for standard swabs & brushesVandalia 34” (shotgun cleaning rod) ....................................11-92-20

Models with rotation in the handle -- for those of you who insist on shooting those new-fangled breech loaders:Camp Perry 36”(.22 thru .26 caliber) ...................................11-92-01Camp Perry II 44” (.22 thru .26 caliber) ..............................11-92-02Laramie 10” (.22 caliber & larger).......................................11-92-03Laramie Silhouette 16” (.22 caliber & larger) .....................11-92-04Wimbledon 36” (.28 caliber & larger) .................................11-92-05Wimbledon II 44” (.28 caliber & larger) .............................11-92-06

GI CLEANING& LOADING ROD

In the past the "GI" onepiece steel cleaning rods, whichmade very good muzzleloadingrange rods, were readily availableat most gun shows. The availabilityseems to have dried up in recentyears; therefore TRESO hasre-introduced its version of thisfamous rod. The one-piece concepthas been retained but in severaldifferent lengths. The steel or brassshaft is 5/16" diameter with a10x32 threaded end. As on theoriginal GI model, the "T" handleswivels. TRESO has added a smallcross hole through the handle andshaft so the handle may be madenon-rotating with a piece of wire orsmall nail, allowing the use of abullet puller. With handle rotation,the cleaning patch on a jag will follow the spiral of the rifling, giving abetter cleaning action. Use standard TRESO 10x32 threaded accessorieswith the GI Rod such as the button jag, bullet puller or worm. As withall loading and cleaning rods, you should use a rod guide to protect thebore from rod wear.Sectional GI Rod: The sectional rod, in steel or brass, comes with three9” segments that can be formed into whatever length is needed--from17¼” to 44” long. It can easily be broken down to fit in a hunter’s pack.

.oN metInoitpircseD

12“ GI Rod, steel ................................................................1 1-94-1212“ GI Rod, brass ...............................................................1 1-95-1227” GI Rod, steel ................................................................1 1-94-2727” GI Rod, brass ...............................................................1 1-95-2731” GI Rod, steel ................................................................1 1-94-3131” GI Rod, brass ...............................................................1 1-95-3134” GI Rod, steel ................................................................1 1-94-3434” GI Rod, brass ...............................................................1 1-95-3444” GI Rod, steel ................................................................1 1-94-4444” GI Rod, brass ...............................................................1 1-95-4444” Sectional GI Rod (5 sections), steel ............................1 1-94-0244” Sectional GI Rod (5 sections), brass ............................1 1-95-02


5/16” x 48” Acetal (Plastic) ............................................... 13-03-5483/8” x 36” Acetal (Plastic) .................................................. 13-03-6363/8” x 48” Acetal (Plastic) .................................................. 13-03-648

ACETAL RAMROD BLANKS (PLASTIC)


RAMRODTIPSTRESO ramrod tips have a spherically cupped end which will center the ramrod over the ball, thus preventing damage to the ball or barrel. Tips are available in steel or brass with either 8-32 or 10-32 thread to accept standard jags and other accessories. The 5/16” diameter tips is 1¼” long; all others are 1½” long. These tips are normally installed on a ramrod with a cross pin for secure fastening.

Description 8-32 10-32 8-32 10-32

Brass Ramrod Tips 5/16” Ramrod Tip 11-11-508 11-11-510 12-11-508 12-11-510 3/8” Ramrod Tip 11-11-608 11-11-610 12-11-608 12-11-610 716” Ramrod Tip 11-11-708 11-11-710 12-11-708 12-11-7101/2” Ramrod Tip 11-11-808 11-11-810 12-11-808 12-11-810

Steel Ramrod Tips 5/16” Ramrod Tip 11-12-508 11-12-510 12-12-508 12-12-510 3/8” Ramrod Tip 11-12-608 11-12-610 12-12-608 12-12-610 7/16” Ramrod Tip 11-12-708 11-12-710 12-12-708 12-12-710

Item No. Bulk No.


Brass TipsBall Seater Tip for 3/8” rod ......................11-11-01 .........12-11-01Jag Adapter Tip for 3/8” rod ....................11-11-02 .........12-11-02Seater & Jag (pair) for 3/8” rod ...............11-11-03 .........12-11-03.32 Seater Tip (5/16” dia.) ........................11-11-11 .........12-11-11.36 Seater Tip (5/16” dia.) ........................11-11-12 .........12-11-12.45 Seater Tip (5/16” dia.) ........................11-11-13 .........12-11-13Jag Adapter Tip (5/16” dia.) .....................11-11-14 .........12-11-14.32 Seater & Tip (pair) .............................11-11-15.36 Seater & Tip (pair) .............................11-11-16.45 Seater & Tip (pair) .............................11-11-17

Steel TipsBall Seater Tip for 3/8” rod ......................11-11-21 .........12-11-21Jag Adapter Tip for 3/8” rod ....................11-11-22 .........12-11-22Ball Seater & Jag Adapter (pair) for 3/8” rod .................................11-11-23 .........12-11-23

T/C & CVA TYPERAMROD ENDSWith one additional feature these brass and steel ramrod ends are made in the same style as the T/C and CVA ramrod ends - the ball seating end has an 8-32 female thread (except the 5/16” diameter size). A rod made with these ends will have a 10-32 thread in one end and a 8-32 thread in the other end. The jag adapter is designed to use a button type jag.


T/C Hawken ramrod, brass tips (all calibers) 28 5/8” .........11-93-01T/C Renegade ramrod, steel tip (all calibers) 26 5/8” .........11-93-02T/C Seneca, .36 Caliber, brass tip 5/16’ dia. x 27 1/2” ........11-93-03T/C Seneca, .45 Caliber, brass tip 5/16” dia. x 27 1/2” .......11-93-04T/C Cherokee, .32/.36 Caliber 5/16” dia. x 24 1/2” ............11-93-05T/C Cherokee, .45 Caliber, brass tip 5/16” dia x 24 1/2” ....11-93-06T/C White Mountain Carbine 21 5/8”..................................11-93-07Lyman Deerstalker 24 3/4” ..................................................11-93-08Lyman Great Plains Rifle 33” ..............................................11-93-09T/C New Englander, Rifle 27” .............................................11-93-10T/C New Englander, Ryanite Rifle 25” ................................11-93-12T/C New Englander, Shotgun ..............................................11-93-11T/C Scout 20 5/8” ................................................................11-93-15Savage Ramrod 22” .............................................................11-93-22

FIBERGLASS REPLACEMENT RAMRODSThese fiberglass replacement ramrods are identical in style and dimen-sions to many original equipment ramrods. Tips on both ends are similar to the Thompson/Center style in appropriate brass or blued steel.The ball seater end has a 8-32 thread and the jag adapter end has a 10-32 thread. The fiberglass ramrod is truly the only unbreakable ramrod available. With its inherent stiffness, this rod is ideal for the hunting rifle. It will not swell like wood under wet conditions.


“T” Handle with 8-32 threads ....................11-79-08 ...12-79-08“T” Handle withe 10-threads .....................11-79-10 ...12-79-10

RAMROD“T” HANDLES This three inch long aluminum handle comes with a 8-32 or 10-32 steel stud to screw into one end of a ramrod converting it into a convient cleaning rod.


page 10


.45 cal. for 3/8” Ramrod ..........................11-17-456 .......12-17-456

.50 cal. for 3/8” Ramrod ..........................11-17-506 .......12-17-506

.50 cal. for 7/16”Ramrod .........................11-17-507 .......12-17-507

.54 cal. for 3/8” Ramrod ..........................11-17-546 .......12-17-546

.54 cal. for 7/16” Ramrod ........................11-17-547 .......12-17-547

RAMROD JAG-TIPThese brass one piece ramrod tip and jag combinations have 10-32 threads to accept standard ramrod accessories. The jag has a spherically cupped end which will center ramrod over ball, thus preventing damage to the ball or barrel.


Combination Base & Jag.45 cal. Jag & 3/8” base ...........................11-19-456 .......12-19-456.50 cal. Jag & 3/8” base ...........................11-19-506 .......12-19-506.50 cal. Jag & 7/16” base .........................11-19-507 .......12-19-507.54 cal. Jag & 3/8” base ...........................11-19-546 .......12-19-546.54 cal. Jag & 7/16” base .........................11-19-547 .......12-19-547.58 cal. Jag & 3/8” base ...........................11-19-586 .......12-19-586.58 cal. Jag & 7/16” base .........................11-19-587 .......12-19-587.62 cal. Jag & 7/16” base .........................11-19-627 .......12-19-627.69 cal. Jag & 1/2” base ...........................11-19-698 .......12-19-698.75 cal. Jag & 1/2” base ...........................11-19-758 .......12-19-758

Combination Bases3/8” dia. base with ball puller ..................11-18-06 .........12-18-067/16”dia. base with ball puller .................11-18-07 .........12-18-071/2” dia. base with ball puller ..................11-18-08 .........12-18-08

Combination Jags.45 cal. for 3/8” base ................................11-18-456 .......12-18-456.50 cal. for 3/8” base ................................11-18-506 .......12-18-506.50 cal. for 7/16” base ..............................11-18-507 .......12-18-507.54 cal. for 3/8” base ................................11-18-546 .......12-18-546.54 cal. for 7/16” base ..............................11-18-547 .......12-18-547.58 cal. for 3/8” base ................................11-18-586 .......12-18-586.58 cal. for 7/16” base ..............................11-18-587 .......12-18-587.62 cal. for 3/8” base ................................11-18-626 ......12-18-626.62 cal. for 7/16” base .............................11-18-627 .......12-18-627.62 cal. for 1/2” base ................................11-18-628 .......12-18-628.69 cal. for 1/2” base ................................11-18-698 .......12-18-698.75 cal. for 1/2” base ................................11-18-758 .......12-18-758

COMBINATIONRAMROD TIP-JAG-BULLET PULLERThe base for the combination ramrod tip has a built in steel lag screw for pulling bullets or retrieving lost patches. A jag or cover can be screwed on the base over the bullet puller. All parts are brass except for the steel bullet puller screw. This is the same tips that are on the TRESO Patriot Series 82 replacement ramrods.

COMBINATION BASE COVERThese covers can be used in place of the jag to cover the bullet puller screw on the end of combination tips. This type of end was often used on the back end of old original ramrods and went down inside the stock ramrod hole.


Cover for 3/8” Base Tip ...........................11-18-16 .........12-18-16Cover for 7/16” Base Tip .........................11-18-17 .........12-18-17

SHOTGUN RAMROD TIPSThis is a brass loading tip for shotguns, very much like those found on old original high quality shotguns. The tip should be pinned on the wood ramrod for a secure attachment.


10 ga. for 3/8” rod Shotgun Tip ...........................................11-20-10612 ga. for 3/8” rod Shotgun Tip ...........................................11-20-12612 ga. for 7/16” rod Shotgun Tip .........................................11-20-12720 ga. for 3/8” rod Shotgun Tip ...........................................11-20-20620 ga. for 7/16” rod Shotgub Tip .........................................11-20-20710 ga. for 7/16” rod Shotgun Tip .........................................11-20-107

SHOTGUN JAG TIPThis tip is made from brass and is designed for use as a loading and cleaning tip for shotgun ramrods. It is available to fit 3/8” or 7/16” diameter ramrods. The end of the jag is flat to seat shotgun wads.


10 ga. for 3/8” rod Shotgun Jag Tip .........11-21-106 .......12-21-10612 ga. for 3/8” rod Shotgun Jag Tip .........11-21-126 .......12-21-12612 ga. for 7/16” rod shotgun Jag Tip........11-21-127 .......12-21-12720 ga. for 3/8” rod Shotgun Jag Tip .........11-21-206 .......12-21-20620 ga. for 7/16” rod Shotgun Tip .............11-21-207 .......12-21-20710 ga. for 7/16” rod Shotgun Jag Tip .......11-21-107 .......12-21-107



Rod Guide for 1/4” ramrods ....................11-23-4 ...........12-23-4Rod Guide for 5/16” ramrods ..................11-23-5 ...........12-23-5Rod Guide for 3/8” ramrods ....................11-23-6 ...........12-23-6

ROD GUIDEThis handy brass ramrod guide protects the bore at the muzzle from wear during cleaning and loading. The guide touches only the crown of the bore. The conical shape allows the guide to be used with all calibers. All loading and cleaning ramrods of wood, steel and fiberglass will wear the bore with repeated use without a rod guide.

These brass button jags are for small diameter ramrods and cleaning rods where a tapered shank jag is not necessary for patch clear-ance. The jags have a spherically cupped end to allow loading a muzzleloader without removing the jag from the ramrod. This is the jag recommended for the Durango Gun Rod. All jags have a steel threaded stud.

BUTTON JAG

Description 8-32 10-32 8-32 10-32

Item No. Bulk No.

Rifle Jags .30 Button Jag 11-15-30 .32 Button Jag 11-15-32 11-16-32 12-15-32 12-16-32.36 Button Jag 11-15-36 11-16-36 12-15-36 12-16-36 .38 Button Jag 11-15-38 12-15-38 .40 Button Jag 11-15-40 12-15-40 .44 Button Jag 11-15-44 12-15-44 .45 Button Jag 11-15-45 11-16-45 12-15-45 12-16-45.50 Button Jag 11-15-50 11-16-50 12-15-50 12-16-50.54 Button Jag 11-15-54 11-16-54 12-15-54 12-16-54.58 Button Jag 11-15-58 11-16-58 12-15-58 12-16-58.62 Button Jag 11-15-62 11-16-62.69 Button Jag 11-15-62 11-16-69.75 Button Jag 11-15-75 11-16-75 Shotgun Jags 10 ga. Jag 11-15-10 11-16-10 12-15-10 12-16-1012 ga. Jag 11-15-12 11-16-16 12-15-16 12-16-1616 ga. Jag 11-15-16 11-16-16 12-15-16 12-16-20 20 ga. Jag 11-15-20 11-16-20 12-15-20 12-16-20410 ga. Jag 11-15-24 11-16-24 12-15-24 12-16-24

FOULINGSCRAPERSThe fouling scraper is a ramrod accessory used to scrape loose the foul-ing build-up on the breech plug of most muzzle loaders. They are made of brass with 8-32 or 10-32 threaded steel stud.

Item No. Bulk No.

Description 8-32 10-32 8-32 10-32

.32 Fouling Scraper 11-37-32 11-38-32 12-37-32 12-38-32

.36 Fouling Scraper 11-37-36 11-38-36 12-37-36 12-38-36

.40 Fouling Scraper 11-37-40 11-38-40 12-37-40 12-38-40

.45 Fouling Scraper 11-37-45 11-38-45 12-37-45 12-38-45

.50 Fouling Scraper 11-37-50 11-38-50 12-37-50 12-38-50

.54 Fouling Scraper 11-37-54 11-38-54 12-37-54 12-38-54

.58 Fouling Scraper 11-37-58 11-38-58 12-37-58 12-38-58

.62 Fouling Scraper 11-37-62 11-38-62 12-37-62 12-38-62

.69 Fouling Scraper 11-37-69 11-38-69 12-27-69 12-38-69

.75 Fouling Scraper 11-37-75 11-38-75 12-37-75 12-38-75

Description 8-32 10-32 8-32 10-32

.32 Jag-5/16”Rod 11-13-325 11-22-325 12-13-325 12-22-325

.36 Jag-5/16”Rod 11-13-365 11-22-365 12-13-365 12-22-365

.40 Jag-5/16”Rod 11-13-405 11-22-405 12-13-405 12-22-405

.40 Jag-3/8”Rod 11-13-406 11-22-406 12-13-406 12-22-406

.44 Jag-3/8” Rod 11-13-446 11-22-446 12-13-446 12-22-446

.45 Jag-5/16”Rod 11-13-455 11-22-455 12-13-455 12-13-455

.45 Jag-3/8”Rod 11-13-456 11-22-456 12-13-456 12-22-456

.50 Jag-3/8”Rod 11-13-506 11-22-506 12-13-506 12-22-506

.50 Jag-7/16”Rod 11-13-507 11-22-507 12-13-507 12-22-507

.54 Jag-3/8”Rod 11-13-546 11-22-546 12-13-546 12-22-546

.54 Jag-7/16”Rod 11-13-547 11-22-547 12-13-547 12-22-547

.54 Jag-1/2”Rod 11-13-548 11-22-548

.58 Jag-3/8”Rod 11-13-586 11-22-586 12-13-586 12-22-586

.58 Jag-7/16”Rod 11-13-587 11-22-587

.58 Jag-1/2”Rod 11-13-588 11-22-588

.62 Jag -3/8” Rod 11-13-626 11-22-626

.62 Jag -7/16”Rod 11-13-627 11-22-627

.62 Jag-1/2” Rod 11-13-628 11-22-628

.69 Jag-3/8” Rod 11-13-696 11-22-696

.69 Jag -7/16”Rod 11-22-697

.69 Jag -1/2” Rod 11-22-698

Item No. Bulk No.

CLEANING JAGSTRESO cleaning jags will fit the above ramrod tips and other makes with 8-32 or 10-32 threads. Jags are made from brass with a steel threaded stud to prevent the breakage that can occur with brass studded jags. These jags also feature a spherically cupped end allowing the user to load without removing the jag the from ramrod. The grooved bands around the head of the jag will firmly grip the cleaning patch.

CUSTOM RAMRODSNeed a ramrod of a combination of material, tips and length we don’t offer? Contact us and tell us what you want for a quote.


page 12

BULLET PULLERThe TRESO bullet puller consists of a steel bullet puller lag screw with a 1/4” hexagonal collar and an attached brass disk. The brass disc has a minimum clearance in the barrel assuring the lag screw is centered over the ball and prevented from

deflecting to the side of the ball and possibly damaging the barrel bore. The hexagonal collar provides a means to remove the puller from the ramrod and/or bullet with a small wrench. These bullet pullers are avail-able with 8-32 and 10-32 threads.

Item No. Bulk No.

Description 8-32 10-32 8-32 10-32

.32 cal Bullet Puller 11-28-32 11-29-32 12-28-32 12-29-32







.62 cal Bullet Puller 11-28-62 11-29-62 12-29-62



PATCH PULLINGWORM

“The Worm” is constructed from a heavy gauge steel wire that will not break under heavy usage. The wire screw form is attached to a brass base with a steel threaded stud. The worm can be used in .32 caliber bores and larger.

Description 8-32 10-32 8-32 10-32

Item No. Bulk No.

“The Worm” 11-32-08 11-32-10 12-32-08 12-32-10

BULLET PULLER SCREWSThis screw is 1” long with 1/2” of machine screw threads on one end and 3/8” of lag screw threads on the other end. There is an integral hexagonal collar for removal with a small wrench. Two thread sizes are available.

Item No. Bulk No.

Description 8-32 10-32 8-32 10-32

Bullet Puller Screw 11-33-08 11-33-10 12-33-08 12-33-10

THREAD ADAPTERThis adapter will convert ramrod threads allowing the use of various cleaning and loading accessories.


8-32 male to 5/16”-27 female 3/8” dia. ...11-34-08 .........12-34-0810-32 male to 5/16”-27 female 3/8” dia. .11-34-10 .........12-34-108-32 male to 10-32 female 5/16” dia. ......11-34-810 .......12-34-8108-32 male to 10-32 female 3/8” dia. ........11-34-820 .......12-34-82010-32 male to 8-32 female 5/16” dia. ......11-34-108 .......12-34-10810-32 male to 8-32 female 3/8” dia. ........11-34-208 .......12-34-208


.22 cal. Jag ............................................................................11-14-22

.24 cal. Jag ............................................................................11-14-24

.26 cal. Jag ............................................................................11-14-26

.28/7mm Jag .........................................................................11-14-28

SMALL CALIBERJAGSThese all-brass jags are for the modern small calibers. They are made for our Durango Gun rod and will fit all other standard small bore clean-ing rods with 8-32 threads.

MUSKET RAMROD ADAPTERSThese adapters screw on the male threads of steel musket ramrods providing a female 10-32 thread for all the various ramrod accessories that are available. The adapter is 2.5 inches long providing a little extra length to the ramrod.


Endfield Musket Rod Adapters ................11-34-910 .......12-34-910Springfield/Brown Bess Musket Rod Adapters ........................11-34-912 .......12-34-912Colt Musket Rod Adapters .......................11-34-914 .......12-34-914

BULLET SEATINGATTACHMENTSolid brass ramrod attachment for starting and seating ballistic-tip bullets. The AT model is for PowerBelt Aero Tip bullets available in 8x32 and 10x32 threads.

Bullet Seating Attachment, AT, 8x32 ......... 11-26-10 ........ 12-26-10

Desctiption Item No. Bulk No.

Bullet Seating Attachment, AT, 10x32 ........ 11-26-11 ........ 12-26-11


Nipples for #11 capsRifle-¼x28 (T/C Nipple) ................................. 11-50-01............ 12-50-01Lyman Rifle M6-.75 (old style)*.................... 11-50-03............ 12-50-03Lyman Rifle M6-.75 (new style)**................ 11-50-66............ 12-50-66Rifle M6-1 (CVA Nipple) ................................ 11-50-05............ 12-50-05Rifle-¼x32 (Numrich Nipple) ......................... 11-50-04............ 12-50-04Rifle/Pistol-¼x28 (shorter length) .................. 11-50-11 ............ 12-50-11Shotgun-9/32x26 (India Shotgun) ................... 11-50-06............ 12-50-06Pistol/Revolver-M6-.75 (old Italian Rev.) ....... 11-50-10............ 12-50-10Pistol/Revolver-M6-.75 (6-pack) ..................... 11-50-106Pistol/Revolver-M5.5x.9 (new Italian Rev.) .... 11-50-16............ 12-50-16Pistol/Revolver-M5.5x.9 (6-pack) ................... 11-50-166Pistol/Rifle (T/C Pat/Sen/Cher) 12-28 ............ 11-50-15........... 12-50-15Ruger Revolver 12-28 (no “hex” shoulder)..... 11-50-12........... 12-50-12Ruger Revolver 12-28 (6-pack)....................... 11-50-126Itilian Colt Walker (1/4-28) ............................. 11-50-13............ 12-50-13Original Colt Revolver (.225-32) .................... 11-50-17............ 12-50-17.31 cal. Italian Revolver M5.5x.9 .................... 11-50-30............ 12-50-30.31 cal. Italian Revolver M5.5x.9 (5-pack)...... 11-50-305.31 cal. Italian Revolver M5.5x.9 (6-pack)...... 11-50-306British Enfield Musket (5/16-18) ..................... 11-50-58............ 12-50-58Musket-5/16x24 (U.S.Musket-#11 cap) .......... 11-50-51............ 12-50-51Italian Muskets (M8x1) ................................... 11-50-59............ 12-50-59Ten-X Special-¼x28 (special Ten-X Pistol) .... 11-50-022

* ** The old style Lyman nipple is .435” from shoulder to top of cone; new style is .380”

Nipples for Musket CapsMusket-5/16x24 (U.S. muskets) ...................... 11-50-50............ 12-50-50Musket-5/16x24 (original U.S. muskets)......... 11-50-50S .........12-50-50SBritish Enfield Muskets (5/16-18) ................... 11-50-52............ 12-50-52Colt’s Colt Musket (8-1) .................................. 11-50-53............ 12-50-53Original U.S. Muskets (oversize 5/16-24) ....... 11-50-54............ 12-50-54Original Maynard Carbine (.260x24) .............. 11-50-55............ 12-50-55Italian Muskets (8-1.25)................................... 11-50-56............ 12-50-56Rifle-¼x28 (T/C, for musket caps) .................. 11-50-02............ 12-50-02Rifle-6x.75mm (Lyman, for musket caps) ....... 11-50-09............ 12-50-09Rifle-6x1mm (CVA, for musket caps) ............. 11-50-08............ 12-50-08

Special OVERSIZE Nipples uses #11 caps(REQUIRES OVER-SIZE TAP)Rifle-.255 x 28 (.005” oversize thread) ........... 11-50-20............ 12-50-20Rifle-.260 x 28 (.010” oversize thread) ........... 11-50-21............ 12-50-21Rifle-.265 x 28 (.015” oversize thread) ........... 11-50-22............ 12-50-22Rifle-.270 x 28 (.020” oversize thread) ........... 11-50-23............ 12-50-23Rifle-.275 x 28 (.025” oversize thread) ........... 11-50-24............ 12-50-24Rifle-.285 x 28 (.035” oversize thread) ........... 11-50-25............ 12-50-25

AMPCONIPPLES TRESO nipples are made from Ampco, a tough alloy with a tensile strength of 118,000 psi, which is tougher than most steels used in muzzleloading barrels. This material provides more resistance to repeated blows from the hammer, and the high thermal conductivity of Ampco alloy affects a faster heat dissipation. This dissipation reduces erosion of the small base hole and assures a longer lasting nipple. All nipples have a small base hole (.028”) to greatly reduce the amount of escaping powder gases. Many muzzle loading experts feel an added benefit of the small base hole is the hot gases from the percussion cap are more concentrated and uniformly directed against the powder chamber.

page 13


FLINTLOCK TOUCH HOLE LINERS TRESO touch hole liners are made from the same tough and erosion resistant Ampco alloy as the TRESO nipples. The flash hole is .0625 diameter. The TRESO flint touch hole liner is installed in a 1/4” x 28 thread in the side of the barrel with a wrench. A new model, available in two thread sizes is removable with a screw driver and is handy for interchangeable flint/percussion lock firearms. We recommend anti-seize material be coated on nipple and touch hole liner threads to make them more easily removed. (Specific installation instructions are listed below. )

INSTALLATION INSTRUCTIONS (wrench model): Drill and tap the barrel for ¼x28 thread at the proper location at the breech. Slightly countersink hole with a 82° countersink. Install and note if any liner protrudes into the barrel bore; if it does, shorten inside end to appropriate length. Tighten liner securely with standard rifle nipple wrench and file flush with outside of barrel. To remove, enlarge touch hole and remove with broken bolt (easy-out) extractor.

INSTALLATION INSTRUCTIONS (screwdriver model): For firearms with interchangeable flint/percussion locks, use 5/16”x24 thread and matching percussion drum (install drum and percussion lock first for proper location). Use ¼x28 thread size for touchhole only replacement applications. Drill and tap breech with appropriate thread and slightly chamfer threaded hole with 82° countersink. Install touch hole liner with screw driver. Touch hole liner should be flush with outside of barrel, if not, adjust chamfer. Check for clearance inside of bore and shorten touch hole liner if necessary.


M5-.8 Touch Hole Liner-CVA .................11-50-94 .........12-50-94M6-.75 Touch Hole Liner-LYMAN .........11-50-95 .........12-50-95M8-1.25 Pedersoli Touch Hole Liner ......11-50-96 .........12-50-961/4-28 Touch Hole Liner with Screw Driver Slot ...........................11-50-97 .........12-50-97 5/16-24 Touch Hole Liner with Screw Driver Slot ...........................11-50-98 .........12-50-981/4-28 Touch Hole Liner-wrench Type ....11-50-99 .........12-50-99


page 14


Hammer Screw, 5-40 thread ............................ 11-47-540 ........... 12-47-540Hammer Screw, 6-40 thread ........................... 11-47-640 ........... 12-47-640Hammer Screw, 8-32 thread ........................... 11-47-832 ........... 12-47-832

REPLACEMENTHAMMER SCREWS These nicely turned hammer screws are made in several thread sizes as replacements for many common newmade locks or many old original locks. They are made of steel and have a “in-the-white” finish. The 8-32 size will fit large Siler locks. The 6-40 will fit small Siler locks. The 5-40 thread will fit many other American made locks such as Davis, Long, L & R, etc.


8-32 Standard Screw 2”long (5/16”head) ....... 11-42-528 ........... 12-42-5288-32 Deluxe Screw 2”long (5/16”head) .......... 11-43-528 ........... 12-43-5288-32 Deluxe Screw 2”long (3/8”head) ............ 11-43-628 ........... 12-43-628

10-32 Standard Screw 2”long (3/8”head) .......... 11-42-620 ........... 12-42-62010-32 Standard Screw 2¼”long (3/8”head) ....... 11-42-630 ........... 12-42-63010-32 Deluxe Screw 2¼”long (5/16”head) ........ 11-43-530 ........... 12-43-53010-32 Deluxe Screw 2¼”long (3/8”head) .......... 11-43-630 ........... 12-43-630

TANG SCREWS Tang screws are offered in deluxe and standard versions. The deluxe model has a slightly domed head. The standard tang screw has a flat head. Both are designed for standard 82° counter sink and are available in different lengths, head diameters and thread size.


8-32 Deluxe Screw 1¾”long (5/16”head) ........... 11-41-518 ........... 12-41-5188-32 Deluxe Screw 1¾”long (3/8” head) ............ 11-41-618 ........... 12-41-6188-32 Deluxe Screw 2” long (3/8” head) .............. 11-41-628 ........... 12-41-6288-32 Standard Screw 1¾”long (5/16” head) ....... 11-40-518 ........... 12-40-5188-32 Standard Screw 1¾”long (3/8” head) ......... 11-40-618 ........... 12-40-6188-32 Standard Screw 2”long (3/8” head) ............ 11-40-628 ........... 12-40-62810-32 Deluxe Screw 2” long (3/8” head) ............ 11-41-620 ........... 12-41-62010-32 Standard Screw 1¾”long (3/8” head) ....... 11-40-610 ........... 12-40-61010-32 Standard Screw 2”long (3/8” head) .......... 11-40-620 ........... 12-40-620

LOCK SCREWS These steel lock screws are in-the-white. To answer the needs of many different applications and uses by gunsmiths, TRESO makes a variety of sizes and lengths in 8-32 and 10-32 threads. The Deluxe Lock Screw has a nicely turned derby shaped head. Adequate threads are provided for shortening the screw length.


8-32 TR Screw 2¼”long (3/8”head) ............. 11-44-638 ............... 12-44-6388-32 TR Screw 2¼”long (7/16”head) ........... 11-44-738 ............... 12-44-73810-32 TR Screw 2 3/4”long (7/16”head) ...... 11-44-750 ............... 12-44-750

TRADE RIFLE SCREWS These screws have the larger oval head and extra length that is needed for the typical trade rifle. There are adequate threads provided for short-ening the screw.

Treso, llc135 Country Center Drive

Suite F, #251Pagosa Springs, CO 81147

Phone: 970-731-2295Fax: 970-731-5503

Email: [email protected]

Now back under the ownership and management of the original owner, Don C. Miner

CATALOG 2013CATALOG 2013CATALOG 2013

treso muzzleloader accessories catalog 2013

Documents