topic_2_2.ppt
TRANSCRIPT
![Page 1: Topic_2_2.ppt](https://reader035.vdocuments.site/reader035/viewer/2022081603/563db7fc550346aa9a8f7dc5/html5/thumbnails/1.jpg)
CLD 20502 BASIC ENGINEERING WORKSHOP
Topic 2Basic Hand/ Workshop/ Measurement Tool and Their Uses
![Page 2: Topic_2_2.ppt](https://reader035.vdocuments.site/reader035/viewer/2022081603/563db7fc550346aa9a8f7dc5/html5/thumbnails/2.jpg)
Marking out is, essentially; Drawing on metal so as to provide guide
lines for cutting out templates and blanks. For marking where sheet metal is to be
folded. Holes are to be drilled or punched in the
component. The line is usually scribed using a sharp
pointed metal tool which leaves a fine, permanent line.
![Page 3: Topic_2_2.ppt](https://reader035.vdocuments.site/reader035/viewer/2022081603/563db7fc550346aa9a8f7dc5/html5/thumbnails/3.jpg)
Types of Datum
![Page 4: Topic_2_2.ppt](https://reader035.vdocuments.site/reader035/viewer/2022081603/563db7fc550346aa9a8f7dc5/html5/thumbnails/4.jpg)
Surface Plate▪ Used in layout applications.▪ Provide an accurate reference plane from
which measurements for both layout and inspection may be made.
![Page 5: Topic_2_2.ppt](https://reader035.vdocuments.site/reader035/viewer/2022081603/563db7fc550346aa9a8f7dc5/html5/thumbnails/5.jpg)
Scribing block/ surface gauge A scribing block or surface gauge is used for
marking outlines parallel to a datum surface or a datum edge.
The scribing point is set to mark a line at a given height above the base of the instrument. This line will be marked parallel to the surface along which the base of the instrument is moved. When a line parallel to a datum edge is required, the edge pins are lowered. These pins are then kept in contact with the datum edge as the scribing block is moved along the work.
![Page 6: Topic_2_2.ppt](https://reader035.vdocuments.site/reader035/viewer/2022081603/563db7fc550346aa9a8f7dc5/html5/thumbnails/6.jpg)
Scribing block/ surface gauge
![Page 7: Topic_2_2.ppt](https://reader035.vdocuments.site/reader035/viewer/2022081603/563db7fc550346aa9a8f7dc5/html5/thumbnails/7.jpg)
Scriber Use to produce fine
lines. It consists of a handle
with a sharp point.
![Page 8: Topic_2_2.ppt](https://reader035.vdocuments.site/reader035/viewer/2022081603/563db7fc550346aa9a8f7dc5/html5/thumbnails/8.jpg)
Scriber The application of
scriber.
![Page 9: Topic_2_2.ppt](https://reader035.vdocuments.site/reader035/viewer/2022081603/563db7fc550346aa9a8f7dc5/html5/thumbnails/9.jpg)
The divider, trammel and compass. Use to mark a circular shape. It has 2
points sharp edge.
![Page 10: Topic_2_2.ppt](https://reader035.vdocuments.site/reader035/viewer/2022081603/563db7fc550346aa9a8f7dc5/html5/thumbnails/10.jpg)
The divider, trammel and compass. The application of divider and compass
![Page 11: Topic_2_2.ppt](https://reader035.vdocuments.site/reader035/viewer/2022081603/563db7fc550346aa9a8f7dc5/html5/thumbnails/11.jpg)
The divider, trammel and compass. The application of trammel
![Page 12: Topic_2_2.ppt](https://reader035.vdocuments.site/reader035/viewer/2022081603/563db7fc550346aa9a8f7dc5/html5/thumbnails/12.jpg)
Center punch Use to making indentation in the surface
of the metal.
![Page 13: Topic_2_2.ppt](https://reader035.vdocuments.site/reader035/viewer/2022081603/563db7fc550346aa9a8f7dc5/html5/thumbnails/13.jpg)
Center punch The application of center punch
![Page 14: Topic_2_2.ppt](https://reader035.vdocuments.site/reader035/viewer/2022081603/563db7fc550346aa9a8f7dc5/html5/thumbnails/14.jpg)
Vernier height gauge Use to measure
height or length of any object.
![Page 15: Topic_2_2.ppt](https://reader035.vdocuments.site/reader035/viewer/2022081603/563db7fc550346aa9a8f7dc5/html5/thumbnails/15.jpg)
Vernier height gauge The application of
vernier height gauge.
![Page 16: Topic_2_2.ppt](https://reader035.vdocuments.site/reader035/viewer/2022081603/563db7fc550346aa9a8f7dc5/html5/thumbnails/16.jpg)
Hand/ Workshop tool is use for cutting, shaping, assembly and fixing of the workpiece.
![Page 17: Topic_2_2.ppt](https://reader035.vdocuments.site/reader035/viewer/2022081603/563db7fc550346aa9a8f7dc5/html5/thumbnails/17.jpg)
Bench Vise & Clamp To clamp a workpiece. Bench vise is attached and fixed to the
worktable.
![Page 18: Topic_2_2.ppt](https://reader035.vdocuments.site/reader035/viewer/2022081603/563db7fc550346aa9a8f7dc5/html5/thumbnails/18.jpg)
Bench Vise & Clamp Clamp can be adjusted on the worktable. There are variety of size and shape (G
clamp, C clamp).
![Page 19: Topic_2_2.ppt](https://reader035.vdocuments.site/reader035/viewer/2022081603/563db7fc550346aa9a8f7dc5/html5/thumbnails/19.jpg)
Ball peen hammer Use to chip and cut
work. Use to round over the
rivet ends. Use to form hardened
work. Has a different shape
of head.
![Page 20: Topic_2_2.ppt](https://reader035.vdocuments.site/reader035/viewer/2022081603/563db7fc550346aa9a8f7dc5/html5/thumbnails/20.jpg)
Ball peen hammer The application of ball peen hammer.
![Page 21: Topic_2_2.ppt](https://reader035.vdocuments.site/reader035/viewer/2022081603/563db7fc550346aa9a8f7dc5/html5/thumbnails/21.jpg)
Nail hammer Use to draw the nails. It has a claw to pull out nail
heads.
![Page 22: Topic_2_2.ppt](https://reader035.vdocuments.site/reader035/viewer/2022081603/563db7fc550346aa9a8f7dc5/html5/thumbnails/22.jpg)
Mallet The mallet is quite similar to the
hammer. Made of wood or rubber. Use to prevent from leaving a mar on
the workpiece such as sheet metal.
![Page 23: Topic_2_2.ppt](https://reader035.vdocuments.site/reader035/viewer/2022081603/563db7fc550346aa9a8f7dc5/html5/thumbnails/23.jpg)
Chisel Use to chipping metal when it is struck
by a hammer. Also use for grooving and shearing. Has a different shape of cutting edge.
![Page 24: Topic_2_2.ppt](https://reader035.vdocuments.site/reader035/viewer/2022081603/563db7fc550346aa9a8f7dc5/html5/thumbnails/24.jpg)
Chisel The uses of chisel
![Page 25: Topic_2_2.ppt](https://reader035.vdocuments.site/reader035/viewer/2022081603/563db7fc550346aa9a8f7dc5/html5/thumbnails/25.jpg)
Plier Use to grasp
workpiece, gripping, wire splicing, wire cutting.
![Page 26: Topic_2_2.ppt](https://reader035.vdocuments.site/reader035/viewer/2022081603/563db7fc550346aa9a8f7dc5/html5/thumbnails/26.jpg)
Screwdrivers Use to install and remove screw. It is important to use a correct tip for a
different screw head.
![Page 27: Topic_2_2.ppt](https://reader035.vdocuments.site/reader035/viewer/2022081603/563db7fc550346aa9a8f7dc5/html5/thumbnails/27.jpg)
Wrenches and Spanner Use to turn capscrew, bolts and nuts. Come with a variety of head size. It has a fix, ring or an adjustable head.
![Page 28: Topic_2_2.ppt](https://reader035.vdocuments.site/reader035/viewer/2022081603/563db7fc550346aa9a8f7dc5/html5/thumbnails/28.jpg)
Hacksaw Use to cut workpiece. The coarser the pitch of the teeth, the
greater will be the rate of metal removal, the quicker the metal will be cut.
![Page 29: Topic_2_2.ppt](https://reader035.vdocuments.site/reader035/viewer/2022081603/563db7fc550346aa9a8f7dc5/html5/thumbnails/29.jpg)
Hacksaw The properties of hacksaw is as shown.
![Page 30: Topic_2_2.ppt](https://reader035.vdocuments.site/reader035/viewer/2022081603/563db7fc550346aa9a8f7dc5/html5/thumbnails/30.jpg)
Files Use to put finishing touch on a machined
workpiece, to remove burrs or sharp edge or as a final fitting operation.
![Page 31: Topic_2_2.ppt](https://reader035.vdocuments.site/reader035/viewer/2022081603/563db7fc550346aa9a8f7dc5/html5/thumbnails/31.jpg)
Files A file is specified by its length, grade of
cut and shape.
![Page 32: Topic_2_2.ppt](https://reader035.vdocuments.site/reader035/viewer/2022081603/563db7fc550346aa9a8f7dc5/html5/thumbnails/32.jpg)
Files Correct grip for different file
applications.
![Page 33: Topic_2_2.ppt](https://reader035.vdocuments.site/reader035/viewer/2022081603/563db7fc550346aa9a8f7dc5/html5/thumbnails/33.jpg)
Files Types of
files and their applications.
![Page 34: Topic_2_2.ppt](https://reader035.vdocuments.site/reader035/viewer/2022081603/563db7fc550346aa9a8f7dc5/html5/thumbnails/34.jpg)
Hand snip Used to cut sheet metal.
![Page 35: Topic_2_2.ppt](https://reader035.vdocuments.site/reader035/viewer/2022081603/563db7fc550346aa9a8f7dc5/html5/thumbnails/35.jpg)
Tap & Dies Tap is use for cutting internal screw
thread.
![Page 36: Topic_2_2.ppt](https://reader035.vdocuments.site/reader035/viewer/2022081603/563db7fc550346aa9a8f7dc5/html5/thumbnails/36.jpg)
Tap & Dies It is use together with tap wrenches
![Page 37: Topic_2_2.ppt](https://reader035.vdocuments.site/reader035/viewer/2022081603/563db7fc550346aa9a8f7dc5/html5/thumbnails/37.jpg)
Tap & Dies Dies is used to cut external screw head.
![Page 38: Topic_2_2.ppt](https://reader035.vdocuments.site/reader035/viewer/2022081603/563db7fc550346aa9a8f7dc5/html5/thumbnails/38.jpg)
Hand reamer Use to finish a hole to an exact
dimension with a smooth finish. The hole usually is drilled undersize and
then used reamer to get the exact dimension and accuracy.
Reamers are also used to remove burrs from the inside of pipe.
![Page 39: Topic_2_2.ppt](https://reader035.vdocuments.site/reader035/viewer/2022081603/563db7fc550346aa9a8f7dc5/html5/thumbnails/39.jpg)
Hand reamer The hand
reamer is used together with the tap wrenches.
![Page 40: Topic_2_2.ppt](https://reader035.vdocuments.site/reader035/viewer/2022081603/563db7fc550346aa9a8f7dc5/html5/thumbnails/40.jpg)
List the action that should be taken to ensure the effective storage and handling of the tool.
![Page 41: Topic_2_2.ppt](https://reader035.vdocuments.site/reader035/viewer/2022081603/563db7fc550346aa9a8f7dc5/html5/thumbnails/41.jpg)