tip catalogt p catalog - farnelltip maintenance and cleaning procedures selecting the proper tip for...
TRANSCRIPT
-
Rev 2000-04
TIP
CA
TA
LO
GT
IP C
ATA
LO
G
-
2
Hakko prides itself in the consistently high quality of the materials and workmanshipthat go into its products, which include our various soldering and desoldering tips.Hakko tips are designed and manufactured for maximum heat conductivity,performance, and life.
TIP MAINTENANCE AND CLEANING PROCEDURES
SELECTING THE PROPER TIP FOR THE JOB.– Short tips with larger dimensions will provide better heat transfer and
performance than longer, thinner tips.
– One common problem is not matching the tip size to the job. This cancause a drop in the performance of your soldering irons and affect thereliability of your work.
– Matching the tip size and configuration to the job is as important as anyother aspect of soldering, and in many cases is more important. Alwaysuse a tip as wide and thick as possible, making sure that it does notinterfere with components or overlap the pad and touch the board.
KEEP TIPS WET.– Applying solder to the working surface of the tip will prevent oxidation and
impurities from building up. This promotes long tip life.
KEEP TIPS CLEAN.– Stroking the tip surface across a clean and properly damp cellulose
sponge will keep flux residues, solder impurities, and oxidation fromforming on the surface of the tip. Immediately re-wet the tip with solderafter wiping, or before any extended period when the iron will not be used.
BASIC STYLE OF HAKKO SOLDERING IRON TIPS
SHAPE A SHAPE B SHAPE C SHAPE D
Pyramid Type
ConicalType
BevelType
ChiselType
* These tips are tinnedon the flat only.
-
33
Table of Contents
Tip Maintenance and Cleaning Procedures . . . . . . . . . . . . .2
For HAKKO Soldering Stations
911 Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4For Model 941
900M/907 & 913 Series . . . . . . . . . . . . . . . . . . . . . . . . . . .6For Models 936, 937, 926, 927, 928, 702, 703, 703B
900L/908 & 914 Series . . . . . . . . . . . . . . . . . . . . . . . . . . . .8For Models 936, 937, 926, 927, 928, 702, 703, 703B
900S Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9For Models 936, 937, 928, 702,703, 703B
903 Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10For Models 939, 929
455 Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13For 455 Iron
456 Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13For 456 Iron
918 Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14For Mach I Iron (models 918)
920 Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15For Mach I Iron (models 920, 921, 922)
N452 Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16For Dash Iron (model N452, N453)
N454 Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17For Dash Iron (model N454)
950 Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18For Models 936, 937, 939, 926, 927, 928, 702, 703, 703B
For HAKKO Desoldering Stations
802/807/808 Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20For Models 470, 470B, 471, 472, 472B, 473, 702, 703, 703B
481 Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21For Models 481, 706
483 Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21For Models 483, 700, 707, 800
For good maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Probable causes of early tip failure . . . . . . . . . . . . . . . . . .23
Discontinued ProductNote: dimensions in ( ) = inches
pg. 4
pgs. 6, 8, 9 & 18
pgs. 6, 8, 9 & 18
pgs. 6, 8, 9 & 18
pg. 10 & 18
pg. 13
pgs. 14 & 15
pgs. 16 & 17
pg. 20
pg. 20
pgs. 6, 8, 9, 18 & 20
pg. 18
-
911 Series
44
T1-08D Shape-0.8D Chisel
0.5(0.02)
2.5(0.1) 7.5
(0.29)
ø0.
8(ø
0.03
1)
T1-12D Shape-1.2D Chisel
0.5(0.02)
2.5(0.1) 7.5
(0.29)
ø1.
2(ø
0.04
7)
T1-16D Shape-1.6D Chisel
0.5(0.02)
3 (0.1)
7.5(0.29)
ø1.
6(ø
0.06
)
T1-24D Shape-2.4D Chisel
0.5(0.02)
(0.14) 3.5
7.5(0.29)
ø2.
4(ø
0.09
)
T1-B Shape-B Conical
R0.2(0.01)
7.5(0.29)
T1-4D Shape-4D Chisel
0.5(0.02)
(0.16) 4
7.5(0.29)
ø4
(ø0.
16)
T1-1BC Shape-1BC Bevel
45
10(0.39)
ø1
(ø0.
04)
T1-2BC Shape-2BC Bevel
45
10(0.39)
ø2
(ø0.
08)
T1-3BC Shape-3BC Bevel
45
10(0.39)
ø3
(ø0.
1)
T1-4C Shape-4C Bevel
45
10(0.39)
ø4
(ø0.
16)
-
911 Series
55
T1-K Shape-K Knife
9.5(0.37)
1.5(0.05)
45
ø 4
(ø
0.16
)
T1-3BCF Shape-3BC Bevel
45
10(0.39)
ø3
(ø0.
1)
(Tinned on soldering surface only.)
T1-4BCF Shape-4C Bevel
45
10(0.39)
ø4
(ø0.
16)
(Tinned on soldering surface only.)
45
10(0.39)
ø2
(ø0.
08)
T1-2BCF Shape-2BC Bevel(Tinned on soldering surface only.)
T1-1BCF Shape-1BC Bevel
45
10(0.39)
ø1
(ø0.
04)
(Tinned on soldering surface only.)
left handed knife tip
T1-KL Shape-KL Knife
9.5(0.37)
1.5(0.05)
45
ø4
(ø0.
16)
T1-2B Shape-2B Conical
R0.5(R0.02)
10(0.39)
T1-02JL Shape-02RLB Bent
R0.2(R0.008)
12(0.47)
30°
3.5
(0.13
)
-
6
900M/907/913 Series
6
900M-T-0.8D
17 mm(.670)
1.2 mm (.047)
0.8 mm (.032)
900M-T-S9
1.0 mm (.040)
900M-T-1.2D
16 mm(.630)
900M-T-1.6D
1.6 mm (.063)
900M-T-2.4D
900M-T-S6
1.3 mm (.050)
60°
17 mm(.670)
17 mm(.670)
2.4 mm (.095)
17 mm(.670)
900M-T-3.2D
3.2 mm (.126)
17 mm(.670)
900M-T-S3
5.2 mm (.205)
19 mm(.748)
17 mm(.670)
Formerly 900M-T-S1
* 900M-T-1CF
900M-T-2C
2.0 mm (.079)
45°
* 900M-T-2CF
900M-T-S7
1.2 mm (.046)
60°
17 mm(.670)
900M-T-1C
1.0 mm (.040)
60°
15 mm(.591)
17 mm(.670)
900M-T-3C
3.0 mm (.118)
45°
* 900M-T-3CF17 mm(.670)
900M-T-4C
4.0 mm (.158)
45°
* 900M-T-4CF17 mm(.670)
.2r (.008)
25 mm(.984)
900M-T-LB
900M-T-B
.5r (.020)
17 mm(.670)
900M-T-I
.2r (.008)
17 mm(.670)
-
7
900M/907/913 Series
7
900M-T-1.2LD
1.2 mm (.047)
900M-T-3.2LD
900M-T-2LD
900M-T-1.8H1.8 mm
(.071)
900M-T-H
900M-T-R
900M-T-K
5.0 mm (.197)
900M-T-S4
3.2 mm(.126)
2.0 mm (.079)
3.2 mm (.126)
.2r (.008)
15 mm(.591)
25 mm(.984)
25 mm(.984)
25 mm(.984)
17 mm(.670)
14 mm(.551)
7.5 mm(0.29)25°
3.5 mm (.138) 19 mm
(.748)
7.5 mm(0.29)25°
15 mm(.591)
45°
5.0 mm (.201)
900M-T-0.2RB
900M-T-RT
17 mm(.670)
900M-T-S8
900M-T-0.5C
.5 mm (.020)
45°
900M-T-0.8C
17 mm(.670)
900M-T-SI
900M-T-SB
15 mm(.591)
15 mm(.591)
15 mm(.591)
35 mm(1.38)
.5r (.020)
2.0 mm(.079)
4.2 mm (.166)
. 2 mm (.01)
4 mm(0.16)30°
.8 mm (.031)
45°
1.5 mm (.059)
60°
*900M-T-1.5CF
2.0 mm (.079)
(.008).2r
14 mm(.551)
13 mm(.512)
(.008).2r
-
8
900L/908/914 Series
8
900L-T-1.6D
20 mm(.788)
2.4 mm (.095)
1.6 mm (.063)
900L-T-3.2D
.2r (.008)
25 mm(.984)
3.2 mm (.126)
900L-T-LB
900L-T-2.4D
20 mm(.788)
20 mm(.788)
900L-T-S1
5.6 mm (.221)
19 mm(.748)
900L-T-B
900L-T-2B
20 mm(.788)
2.0 mm (.079)
.5r (.020)
20 mm(.788)
20 mm(.788)
900L-T-2C
2.0 mm (.079)
45°
* 900L-T-2CF
4.0 mm (.158)
45°
900L-T-4C
5.0 mm (.197)
15 mm(.591)
900L-T-5C
900L-T-3C
3.0 mm (.118)
45°
* 900L - T-3CF
* 900L-T-4CF
* 900L-T-5CF
45°
.2r (.008)
900L-T-I
20 mm(.788)
20 mm(.788)
20 mm(.788)
5.0 mm (.197)
18 mm(.709)
900L-T-K
45°
-
9
900S Series
9
900S-T-1.2D
1.2 mm (.047)
1.6 mm (.063)
1.0 mm (.040)
.2r (.008)
15 mm(.591)
17 mm(.670)
17 mm(.670)
17 mm(.670)
17 mm(.670)
17 mm(.670)
.5r (.020)
45°
60°
900S-T-1.6D
2.0 mm (.079)
900S-T-1C
900S-T-2C
900S-T-B
900S-T-I
-
10
903 Series
10
0.8 mm (.031)
1.6 mm (.063)
SHAPE: 0.8D
SHAPE: 1.6D
SHAPE: 2.4D
SHAPE: 5.2D
SHAPE: B
SHAPE: I
SHAPE: 1.2C
SHAPE: 0.2RB
15 mm(.591)
15 mm(.591)
15 mm(.591)
8 mm(.315)
8 mm(.315)
15 mm(.591)
15 mm(.591)
15 mm(.591)
.2r (.008)
.5r (.020)
.2r (.008)
2.4 mm (.094)
5.2 mm (.205)
A1243
A1244
A1245
A1246
A1247
A1248
A124960°
1.2 mm (.047)
A125060°
SHAPE: SI
SHAPE: 0.8SD
SHAPE: 1.2SD
SHAPE: .04SC
SHAPE: 3.2D
SHAPE: 2.4LD
SHAPE: K
SHAPE: 0.2RSB
A1252
12.0 mm (.472)
10 mm(.394)
14 mm(.557)
15 mm(.591)
.2r (.008)
A1253
A1254
A1255
60°
A1269
30°
.2r (.008)
0.8 mm (.031)
10 mm(.394)
1.2 mm (.047)
0.4 mm (.016)
8 mm(.315)
3.2 mm (.13)
A1256
15 mm(.591)
A12662.4 mm (.094)
5 mm (.197) A1268
15 mm(.591)
45°
-
11
903 Series
11
SHAPE: 1C
SHAPE: 1.2D
SHAPE: 4.5D
4.5 mm (.177)
15 mm(.591)
1.0 mm (.040)
60°
A1270
A1271
15 mm(.591)
A1326
9.9 mm(.390)
1.2 mm (.047)
SHAPE: 0.8SC
14.2 mm(.559)
60°
A1327
0.8 mm (.031)
SHAPE: 0.2RSSB
SHAPE: IS
SHAPE: 2.8C
.2r (.008)
A1328
30°
6.4 mm(.252)
1.6 mm(.063)
14.7 mm(.579)
.2r (.008)
A1329
2.8 mm (.110)
A1330
17.6 mm(.693)
60°
SHAPE: R1 (1.7)
3.4 mm (.134)
1.7 mm (.067)2.5 mm
(.093)6.2 mm
(.242)
A1331
SHAPE: R2 (3.5)
SHAPE: SOP 5.1 X 4.3
SHAPE: SOP 5.1 x 10.2
SHAPE: SOP 9.5 x 13.3
SHAPE: R3 (2.3)
SHAPE: SPATULA 10.4
SHAPE: SPATULA 20.8
SHAPE: 3.2D
5.9 mm (.232)
3.5 mm (.138)1.5 mm
(.059)5.2 mm
(.205)
A1332
6.7 mm (.264)
5.1 mm (.201)4.3 mm
(.169)5.3 mm
(.209)
A1333
10.2 mm (.402)
5.3 mm (.209)
A1334
6.7 mm (.264)
5.1 mm (.201)
13.3 mm (.524)
5.5 mm (.217)
A1335
11.1 mm (.437)
9.5 mm (.374)
1.3 mm (.051)
7.0 mm (.276)
A1336
4.0 mm (.181)
2.3 mm (.091)
10.4 mm (.409)
A1337
0.2 mm (.008)
3.0 mm (.118)
9.5 mm (.374)
20.8 mm (.819)
A1338
0.2 mm (.008)
3.0 mm (.118)
9.5 mm (.374)
0.6 mm (.024)
A1341
3.2 mm (.126)
12.0 mm (.472)
-
12
903 Series
12
SHAPE: PLCC 12.7 x 12.7
SHAPE: PLCC 17.8 x 17.8
SHAPE: PLCC 10.2 x 10.2
SHAPE: PLCC 15.2 x 12.7
12.7 mm (.500)
14.2 mm (.559)
14.2 mm (.559)
4.0 mm (.157)
6.0 mm (.236)
1.5 mm (.059)
A1339
17.8 mm (.701)
19.0 mm (.748)
19.0 mm (.748)
4.0 mm (.157)
6.0 mm (.236)
1.5 mm (.059)
A1340
10.2 mm (.402)
11.5 mm (.453)
11.5 mm (.453)
4.0 mm (.157)
6.0 mm (.236)
1.5 mm (.059)
A1342
12.7 mm (.500)
14.2 mm (.559)
15.2 mm (.598)
4.0 mm (.157)
6.0 mm (.236)
1.5 mm (.059)
A1345
16.7 mm (.657)
SHAPE: 0.2RLB Bent
SHAPE: PLCC 16.4 x 22.4
SHAPE: PLCC 25.5 x 25.5
R0.2 mm (0.008)
7.5 mm (0.3)
A1346
15.8 mm (.062)
6.5 mm (0.25)
22.4 mm (0.88)22.9 mm (0.98)
A1347
30°
16.4
mm
(0.64
)18
.9 m
m (0
.74)
A1348
25.5 mm (1.00)28 mm (1.10)
25.5
mm
(1.00
)28
mm
(1.1
0)
7.5 mm (0.29)
-
13
455/456 Series
13
.5r (.020)
25 mm(.984)
A1047
SHAPE: B
3.0 mm (.118)
A1048
SHAPE: 3C45°
25 mm(.984)
4.0 mm (.158)
A1049
SHAPE: 4C45°
25 mm(.984)
5.0 mm (.197)
A1050
SHAPE: 5C45°
25 mm(.984)
6.0 mm (.236)
A1051
SHAPE: 6C45°
25 mm(.984)
5.0 mm (.197)
A1052
SHAPE: SD
25 mm(.984)
A1053
9.0 mm (.354)
SHAPE: K 45°
25 mm(.984)
1.0r (.040)
30 mm(1.18)
A1023
SHAPE: 2B
4.0 mm (.158)
30 mm(1.18)
A1024
45°SHAPE: 4C
8.0 mm (.315)
26 mm(1.02)
A1025
SHAPE: 8C45°
5.0 mm (.197)
30 mm(1.18)
A1026
SHAPE: SD
6.0 mm (.236)
30 mm(1.18)
A1031
SHAPE: 6C45°
A1032
9.0 mm (.354)
30 mm(1.18)
SHAPE: K 45°
9.0 mm (.354)
30 mm(1.18)
A1179
SHAPE: 9D
455 Series 456 Series
-
14
918 Series
14
1.6 mm (.063)
918-T-1.6D
20 mm(.788)
2.4 mm (.095)
918-T-2.4D
20 mm(.788)
3.0 mm (.118)
918-T-3.2D
20 mm(.788)
918-T-3C
3.0 mm (.118)
45°
22 mm(.866) * 918-T-3CF
918-T-4C
4.0 mm (.158)
45°
20 mm(.788) * 918-T-4CF
918-T-5C
5.0 mm (.197)
45°
20 mm(.788) * 918-T-5CF
918-T-BC
20 mm(.788)
1.6 mm (.063)
60°
918-T-B
20 mm(.788)
.5r (.020)
918-T-6.5D
6.5 mm (.250)
20 mm(.788)
-
15
920 Series
15
1.0 mm (.040)
920-T-1.0D
16 mm(.630)
1.6 mm (.063)
920-T-1.6D
17 mm(.670)
2.4 mm (.095)
920-T-2.4D
17 mm(.670)
3.2 mm (.126)
19 mm(.748)
920-T-BC
19 mm(.748)
1.6 mm (.063)
60°
920-T-3.2D
920-T-2C
2.0 mm (.079)
45°
14 mm(.551)
* 920-T-2CF
920-T-3C
3.0 mm (.118)
45°
14 mm(.551)
* 920-T-3CF
920-T-4C
4.0 mm (.158)
45°
15 mm(.591) * 920-T-4CF
0.5 r (.020)
920-T-B
14 mm(.551)
0.5 r (.020)
920-T-SB
13 mm(.512)
0.5 r (.020)
920-T-I
15 mm(.591)
15 mm(.591)
920-T-A
4.8 mm (.189)
16 mm(.630)
.5 mm (.019)
920-T-R
3.2 mm (.126)
4.2 mm (.166)
16 mm(.630)
920-T-RT
2.0 mm (.079)
-
16
N452 Series
16
N452-T-B
.5r (.020)
N452-T-C
17 mm(.670)
N452-T-SB
2.0 (.079)
17 mm(.670)
1.5 mm (.059)
45°
17 mm(.670)
.08 mm (.032)
45°
17 mm(.670)
N452-T-SC
1.0 mm (.040)
60°
15 mm(.591)
N452-T-1C
2.0 mm (.079)
N452-T-2C
17 mm(.670)
45°
3.0 mm (.118)
N452-T-3C
17 mm(.670)
45°
4.0 mm (.158)
N452-T-4C
17 mm(.670)
45°
* N452-T-1CF
* N452-T-2CF
* N452-T-3CF
* N452-T-4CF
3.0 mm (.118)
N452-T-D
15 mm(.591)
N452-T-SD
2.0 mm(.079)
17 mm(.670)
N452-T-I
.4r (.016)
17 mm(.670)
-
17
N454 Series
17
N454-T-B
.5r (.020)
N454-T-2C
20 mm(.788)
2.0 mm (.079)
45°
23 mm(.905)
4.0 mm (.158)
20 mm(.780)
45°
N454-T-4C
5.0 mm (.197)
20 mm(.788)
N454-T-5C
N454-T-D
.4r (.016)
23 mm(.905)
* N454-T-2CF
N454-T-3C
3.0 mm (.118)
45°
22 mm(.866 ) * N454-T-3CF
* N454-T-4CF
* N454-T-5CF
45°
3.0 mm (.118)
22 mm(.866 )
N454-T-I
-
18
950 Series
18
SOP
A1380 Tip/SOP 8L
8mm (0.31 in.)
A1390 Tip/SOP 4L
4mm (0.16 in.)
A1381 Tip/SOP 10L
10mm (0.39 in.)
A1391 Tip/SOP 6L
6mm (0.24 in.)
A1382 Tip/SOP 13L
13mm (0.51 in.)
A1392 Tip/SOP 15L
15mm (0.91 in.)
A1383 Tip/SOP 18L
18mm (0.71 in.)
A1384 Tip/SOP 20L
20mm (0.79 in.)
A1385 Tip/SOP 25L
25mm (0.98 in.)
-
19
950 Series
19
CHIP
A1379 Tip/CHIP 1L
1mm (0.04 in.)
A1378 Tip/CHIP 2L
2mm (0.08 in.)
CHIP
A1388 Tip/CHIP 0.5C
1.5mm (0.06 in.)
0.5mm(0.02 in.)
45°
A1389 Tip/CHIP 0.5I
R0.25mm (R0.01 in.)
888-080 Tip/CHIP 0.7T
0.5mm (0.02 in.)
888-079 Tip/CHIP 2.6C
2.6mm (0.10 in.)
45°
-
20
802/807/808 Series
20
0.8 mm (.032)
A1002
1.8 mm (.071)
1.0 mm (.040)
A1003
2.0 mm (.079)
0.8 mm (.032)
A1004
2.3 mm (.091)
1.0 mm (.040)
A1005
2.5 mm (.099)
1.3 mm (.051)
A1006
3.0 mm (.118)
1.6 mm (.063)
A1007
3.0 mm (.118)
1.0 mm (.040)
A1393
1.6 mm (.062)
2.3 mm (.091)
A1396
4.0 mm (.157)
1.0 mm (.040)
A1394
2.1 mm (.090)
11 mm (.434)
1.3 mm (.051)
A1395
2.3 mm (.091)
-
21
481/483 Series
21
0.8 mm (.032)
481-T-0.8
2.5 mm (.099)
1.0 mm (.040)
481-T-1.0
2.5 mm (.099)
1.3 mm (.051)
481-T-1.3
2.5 mm (.099)
1.6 mm (.063)
481-T-1.6
3.0 mm (.118)
0.8 mm (.032)
483-T-0.8
2.5 mm (.099)
1.0 mm (.040)
483-T-1.0
483-T-1.3
2.5 mm (.099)
1.3 mm (.051)
3.0 mm (.118)
483-T-1.61.6 mm
(.063)3.0 mm
(.118)
483-T-0.8T0.8 mm
(.032)1.7 mm
(.067)
483-T-1.0T1.0 mm
(.040)2.0 mm
(.079)
483-T-1.3T1.3 mm
(.051)2.3 mm
(.091)
-
2222
Part No. 888-001 Drill for Heating Element Cleans solder and flux from the heatingelement core. Use once a day.
Part No. 888-075 WrenchRemoves and replaces enclosure nut, enclosure and nozzle from heating element.
Part No. A1030 Spring Filter (Set of 10)Captures solder in the handpiece. Replacewhen filter is 1/2 to 1/3 full of solder.
Part No. A1009 Ceramic Paper Filter (S) (Set of 10)Protects the pump by filtering flux vapors atthe desolder station. Replace when face offilter is coated with flux.
Part No. A1033 Ceramic Paper Filter (L) (Set of 10)Protects the pump by filtering flux vapors atthe handpiece. Replace when face of filter iscoated with flux.
Part No. B1915 Filter Holder for 807Holds spring filter (A1030) in filter pipe(B1916). For use with 807 handpiece only.Replace if holder becomes stiff or cracked.
Part No. 777-090 Maintenance Brush Cleans oxides and flux residue from heatercore. Do not use on nozzles as brush willdamage the plating.
888-001
888-075
A1030
777-090
B1915
B1086 - B1089
A1009
Part No. A1042 Cleaning SpongeCleans nozzle of excess solder and oxides.Rinse with water only. Replace spongewhen contaminated.A1042
Part No. A1011 Filter Holder for 802 Holds spring filter (A1030) in filter pipe(B1128). For use with 802 handpiece only.Replace if holder becomes stiff or cracked.
A1011
Part No. B1303 Nozzle Cleaning Drill (1.0mm) with holderDrill bit only: B1308; 0.8mm, B1310;1.3mm, B1311; 1.6mmUsed to remove heavy accumulation of sol-der from the nozzle. Use if cleaning pin cannot clean nozzle.
B1302 - B1305
A1033
P/N HJ2002-01
Desoldering Maintenance K it
For long lasting use of your desoldering tools,Keep Hakko’s “DesolderingMaintenance Kit” by your side!
Part No. B1087 Nozzle Cleaning Pin (1.0mm)B1086: 0.8mm, B1088: 1.3mm, B1089: 1.6mmUsed to clean accumulated solder from thenozzle, preventing clogging. Match cleaningpin diameter to nozzle hole diameter. Useapproximately every two hours of operation.
-
23
PROBABLE CAUSES OF EARLY TIP FAILURE
HIGH LINE VOLTAGE.
– Even though Hakko irons and stations are designed to maintain temperature withslightly varying supply voltages, a consistently high line voltage will cause the iron torun hot. This will reduce tip life.
LOW TIN ALLOY SOLDER.
– The lower the tin content of your solder, the more difficult it will be to keep the tip from‘dewetting’ (losing its protective coat of solder). Keep a roll of large diameter 63-37solder on hand to periodically flush and re-tin the tips.
SMALL DIAMETER SOLDER.
– In many cases, the diameter of the solder being used is too small for effective wettingof the tips. A periodic flooding with a larger diameter solder, as mentioned above, willdo the trick.
DIFFERENCES IN FLUX ACTIONS.(RA, RMA, water soluble, ‘No Clean’ etc.)...
– The more active the flux, the more frequently the tip needs to be cleaned. Oxidationforms at a much higher rate with highly active fluxes. Please check with the solder orflux manufacturer as to the relative activity of the flux you are using.
EXCESSIVE PRESSURE, OR THE PUSHING IN OF HEAT.
– Applying excessive pressure, or rubbing the tip against the joint to ‘force’ heat in, willdestroy the tip faster than normal contact soldering.
TIP TEMPERATURE.
– The higher the tip temperature, the faster oxidation will form. At temperaturesexceeding 875 deg. F, the speed of oxidation is just about twice that at 700 deg. F.
NOTE Tips subjected to proper maintenance and cleaning procedures should last between two to fourweeks, depending upon the temperature, tip configuration, and the job or jobs being performed.
-
American Hakko Products, Inc.25072 Anza Drive, Santa Clarita, CA 91355
www.hakkousa.com
Toll Free: (800) 88-HAKKO (42556)Customer Service: (661) 294-0090
Fax: (661) 294-0096