tiflex catalogue 2013

SCREEN PRINTING

*

* making an impression

LC CARROUSEL- print on tee-shirts, sweat-shirts, caps, ....

SCREENPRINTING mATERIAL

S C R E E N P R I N T I N G

Equipment manufactured in France

IMP.

TIFL

EX 1

1.02

.201

3 - N

on c

ontra

ctua

l pic

ture

s

The LC carrousel is a manual machine dedicated to print 1 to 6 colours on tee-shirts, sweat-shirts, caps... The maximum printing size is 40 x 50 cm.

3 models are manufactured : 4 screens / 4 boards, 6 screens / 6 boards or 6 screens / 4 boards. LC carrousel is composed of a perfectly stable stiff base. The boards and screen holders are rotating independently one from the other. LC carrousel can be equipped with 4 different board sizes : large, man, woman and child. LC carrousel is delivered dismantled.

• Printing system The screen holders are manufactured in mechanic welding section which offers good lightness/stiffness qualities for an easy use. The boards slide to permit their adjustment and quick removing. A roll tappet set them in the appropriate position.

• Adjustments - screens by 3 micrometric buttons (x and y axes and rotation) - boards : front / backward - off contact - parallelism screen/board

LC CARROUSEL 4 moving stations

6 moving stations

4/6 moving stations

MEChAniCAL ChARACtERiStiCS

number of screens : 4 6 6

maxi printing size : 40 x 50 cm 40 x 50 cm 40 x 50 cm

screen maxi outside dimensions : 60 x 80 cm 60 x 80 cm 60 x 80 cm

number of boards : 4 6 4

boards dimensions- large :- man :- woman :- child :

48 x 66 cm40 x 60 cm32 x 50 cm22 x 40 cm

48 x 66 cm40 x 60 cm32 x 50 cm22 x 40 cm

48 x 66 cm40 x 60 cm32 x 50 cm22 x 40 cm

OvERALL diMEnSiOnS

board height on ground : 86 cm 86 cm 86 cm

lift screen height on ground : 1,60 m 1,60 m 1,60 m

maxi outside diameter : 2,90 m 2,90 m 2,90 m

net weight : 180 kg 200 kg 190 kg

gross weight : 220 kg 240 kg 230 kg

BP 3 - 01450 PONCIN - FranceInternational Sales : Tel. +33 (0) 4 74 37 33 80/97 - Fax +33 (0) 4 74 37 33 62 - [email protected] - www.tiflex.com

LC CARROUSEL

SCREEN PRINTING

*


FLASH CURE- intermediate dryer for textile inks

S C R E E N P R I N T I N G m A T E R I A L



Product manufactured in France

IMP.

TIFL

EX 1

1.02

.201

3 - N

on c

ontra

ctua

l pic

ture

s


maxi drying surface : 40 x 40 cm 40 x 60 cm

OUtSidE diMEnSiOnS

overall dimensions- mini p x l x h :- maxi :

100 x 55 x 86 cm

100 x 55 x 121 cm

120 x 55 x 89 cm

120 x 55 x 123 cm

net weight : 35 kg 40 kg

gross weight (open crate) : 85 kg 90 kg

ELECtRiCAL ChARACtERiStiCS

heating : 6 short waves lamps 9 short waves lamps

total power : 12 Kw (6 x 2 Kw) 18 Kw (9 x 2 Kw)

feeding : 380 V tri 380 V tri

intensity : 18 A 27 A

PnEUMAtiCS ChARACtERiStiCS

feeding : air filtening 40 µ air filtening 40 µ

OPtiOn

sliding bars for automatic carrousel: 40 x 40 cm 40 x 60 cm

• BASE It is easily adjustable in height. It is equipped with 4 wheels to facilitate its positioning above the carrousel. For the treatment of fragile meshes, FLASh CURE is equipped with a half-power programming and with a cooling during the heating time.

This unit is one of the strongest in this kind of equipment. it is manufactured in compliance with the nFC 20-30 directive.

Flash can be adapted on automatic MhM carrousels. in that configuration, it is supplied with 2 sliding bars .

FLASh CURE is an intermediate dryer preheater for textile inks. Equipped with short waves infrared transmitters, it is composed of a heating element and a base.

It is available in 2 pre-drying formats : 40 x 40 and 40 x 60 cm.

• thE hEAtinG Unit Depending on the format, it combines several 2 Kw lamps. The start of each cycle is controlled by a contact rod which detects the board under the machine head. A first timer sets precisely the drying time. An air jet cools down the mesh at the end of each cycle. A second timer sets this cooling time. The FLASh CURE heating unit is designed exclusively for intermittent operation.

FLASH CURE

SCREEN PRINTING

*


I.R. DRYING TUNNEL- dedicated to polymerise water based and plastisol inks used in textile industry





IMP.

TIFL

EX 1

1.02

.201

3 - N

on c

ontra

ctua

l pic

ture

s

On request and after study, we can supply combined drying tunnel composed of jet air element, infrared element and cooling section.

i.R. dRYinG tUnnEL iR 80 iR 120 iR 140


useful width 80 cm 120 cm 140 cm

opening 90 x 12 cm 130 x 12 cm 150 x 12 cm

from ground conveyor height 86,5 cm 86,5 cm 86,5 cm

OvERALL diMEnSiOnS

overall width 120 cm 160 cm 180 cm

under element length 260 cm 260 cm 260 cm

overall length 420 cm 420 cm 420 cm

overall height 130 cm 130 cm 130 cm

exit and entry useful length 54 and 34 cm 54 and 34 cm 54 and 34 cm

net weight 365 kg 460 kg 550 kg

gross weight 460 kg 600 kg 660 kg


heating 12 radiant elements600 W

18 radiant elements600 W

21 radiant elements600 W

total power 7,5 kW 11 kW 13 kW

feeding 400 V tri 400 V tri 400 V tri

3-phase intensity 400 V 12 A 19 A 23 A

conveyor speed 0,4 to 6,5 m/mn 0,4 to 6,5 m/mn 0,4 to 6,5 m/mn

operating sound level 80 decibels max. 80 decibels max. 80 decibels max.

infrared drying tunnel is dedicated to polymerise water based and plastisol inks used in the textile industry. it can also be used for solvent based inks (époxy, polyuréthanne, glycéro...) printed on iR resisting surfaces (thermo hardening, metals...).

This equipment is manufactured in the following standard widths : 80, 120 and 140 cm but other sizes can be manufactured on request.

• Working process Polymerisation is obtained with radiant transmitters action on the printed surface.

• Characteristics - under equipment length: 2,60 m - teflon glass conveyor resisting to heat (250°C) - variable conveyor speed from 0.4 to 6.5 m/mn (please, consult us for other reduction ratios) - parallelism and conveyor tension adjustments, stopping collar guiding - collapsible shutters allowing thick support passage such as caps - drying area, controlled by a switch and guided by a temperature regulator with digital display - fumes collector on the drying tunnel exit(125 mm diameter) - metal frame with 4 wheels ensuring an easy moving

I.R. DRYING TUNNEL

SCREEN PRINTING

*


SHORT IR DRYER- dedicated to polymerise water based and plastisol inks used in textile industry





IMP.

TIFL

EX 1

1.02

.201

3 - N

on c

ontra

ctua

l pic

ture

s

On request and after study, we can supply combined drying tunnel composed of jet air element, infrared element and cooling section.

short iR dryer iR 80


useful width 80 cm

opening 90 x 12 cm

from ground conveyor height 86,5 cm

OvERALL diMEnSiOnS

overall width 120 cm

under element length 130 cm

overall length 290 cm

overall height 130 cm

exit and entry useful length 54 and 34 cm

net weight 265 kg

gross weight 360 kg


heating 6 radiant elements 750 W

total power 4,6 kW

feeding 400 V tri

3-phase intensity 400 V 7 A

conveyor speed 0,4 to 6,5 m/mn

operating sound level 80 decibels max.

infrared drying tunnel is dedicated to polymerise water based and plastisol inks used in the textile industry. it can also be used for solvent based inks (époxy, polyuréthanne, glycéro...) printed on iR resisting surfaces (thermo hardening, metals...).

The main characteristic of this tunnel is its reduced length.

• Working process Polymerisation is obtained with radiant transmitters action on the printed surface.

• Characteristics - under equipment length : 1,30 m - teflon glass conveyor resisting to heat (250°C) - variable conveyor speed from 0.4 to 6.5 m/mn (please, consult us for other reduction ratios) - parallelism and conveyor tension adjustments, stopping collar guiding - collapsible shutters allowing thick support passage such as caps - drying area, controlled by a switch and guided by a temperature regulator with digital display - fumes collector on the drying tunnel exit (125 mm diameter) - metal frame with 4 wheels ensuring an easy moving

SHORT IR DRYER

SCREEN PRINTING

*


HLS- this semi-automatic machine enables the printing on plane supports up to 3cm thickness.


This semi-automatic machine enables the printing on plane supports up to 3cm thickness.

rocked

not rocked

Tipping over of the printing head in order to case the squeegee and flood bar setting and removing operations.

Screen lift-off visualisation with restart.

Micrometric adjustment and pressure visualisation of the squeegee and flood bar in order to balance the efforts on the left and right ends.

Robust frame welded mechanic.

Squeegee precise adjustment and slant visualisation.

Squeegee and flood bar pneumatic clamping.

Screen pneumatic clamping (clamping preserved in case of air or electrical cuts).

Fast adjustment of both squeegee and flood bar by a micro contact.

S C R E E N P R I N T I N G HLS

Electrical regulation of except contact given by vertical displacement of the table.Great accessibility of all these adjustments, soft and quiet operation.

Control console apart from the frame.

Management of the functions machine by programmable automat.

Micro plate of impression perforated, honeycomb, out of aluminium resistant to all types of inks and solvents. The HLS can be transformed into 3/4 automatic if it is equipped with the option retractable blocks for exit of sheets on the left or on the right.


IMP.

TIFL

EX 1

1.02

.201

3

Parts and labour garanteed, hLS is supplied with an electrical treadle, two sets of squeegees, scraper blades and the directions for use.hLS 570 S 710 S 812 S 1014 S


maxi printing size : 50 x 70 cm 70 x 100 cm 80 x 120 cm 100 x 140 cm

screen maxi outside dimensions : 96 x 100 x 5 cm 120 x 130 x 5 cm 130 x 150 x 5 cm 150 x 170 x 5 cm

mini front and back margins : 16 cm AV/20 cm AR 18 cm AV/22 cm AR 18 cm AV/22 cm AR 18 cm AV/22 cm AR

printing plate dimensions : 80 x 100 cm 110 x 130 cm 120 x 150 cm 140 x 170 cm

perforated surface : 54 x 74 cm 84 x 106 cm 94 x 126 cm 114 x 146 cm

item maxi thickness : 3 cm 3 cm 3 cm 3 cm

maxi number of cyles/hour sur format maxi : 900 560 500 400

supplied squeegees length : 53 & 73 cm 83 & 103 cm 83 & 123 cm 83 & 143 cm

supplied flood bar length : 54 & 74 cm 84 & 104 cm 84 & 124 cm 84 & 144 cm

OvERALL diMEnSiOnS

plate height on ground : 90 / 96 cm 90 / 96 cm 90 / 96 cm 90 / 96 cm

dimensions on ground p x l : 106 x 123 cm 141 x 161 cm 152 x 193 cm 176 x 225 cm

overall dimensions p x l x h without console : 136 x 133 x 138 cm 170 x 174 x 138 cm 183 x 208 x 138 cm 212 x 240 x 138 cm

net weight : 500 kg 600 kg 660 kg 760 kg

gross weight (wooden box) : 620 kg 760 kg 880 kg 1000 kg


variable speed scraping engine : 0,37 kW 1500 t/mn230/400 V

0,37 kW 1500 t/mn230/400 V

0,75 kW 1500 t/mn230/400 V

0,75 kW 1500 t/mn230/400 V

3-phase for the up and down mvt engine : 0,55 kW 1500 t/mn230/400 V

0,55 kW 1500 t/mn230/400 V

0,75 kW 1500 t/mn230/400 V

0,75 kW 1500 t/mn230/400 V

3-phase vacuum engine : 0,37 kW 2850 t/mn230/400 V

0,37 kW 2850 t/mn230/400 V

1,5 kW 2850 t/mn230/400 V

1,5 kW 2850 t/mn230/400 V

power : 1,5 kW 1,5 kW 2,5 kW 2,5 kW

feeding cable section : 4 x 1,5 mm² 4 x 1,5 mm² 4 x 1,5 mm² 4 x 1,5 mm²

PnEUMAtiC ChARACtERiStiCS

pression : 6 bars 6 bars 6 bars 6 bars

output : 0,20 m³/h 0,20 m³/h 0,20 m³/h 0,20 m³/h

SOUnd ChARACtERiStiCS

operating sound level : 80 décibels maxi 80 décibels maxi 80 décibels maxi 80 décibels maxi



HLS

SCREEN PRINTING

*


SHEET FEED- it carries out the automatic transfer of the support printed between the machine of i pression HLS and tunnels U.V or A.P.





IMP.

TIFL

EX 1

1.02

.201

3 - N

on c

ontra

ctua

l pic

ture

s

the take off system transfers the printed substrate automatically between the hLS printing machine and the Uv or AP tunnels.

It takes the sheets on the hLS, thanks to a pair of pliers. It is coupled electrically and mechanically to the hLS. It is installed to the right or left of the hLS. The latter is therefore equipped with the feed guide and ejector option.

There are two versions of this system: SF 80 for the hLS 570 and 710 and SF 120 for the hLS 812 and 1014.

the take off system conforms to the CEE 89/392 standard. Parts and labour are fully guaranteed for 6 months.

ShEEt FEEd SF 80 SF 120

MEChAniCAL FEAtURES

belt width 800 cm 1 200 cm

maximum belt speed 25 m/mn 25 m/mn

maximum dimensions of sheet for printing 1050 x 750 mm 1 150 x 1 500 mm

minimum margin on jogging side 20 mm 20 mm

maximum thickness of sheet for printing 10 mm 10 mm

maximum weight of sheet for printing 3 kg 3 kg

maximum theoretical rate (cycle start pedal locked) 780 cycles/hour 500 cycles/hour

diMEnSiOnS

overall dimensions ( l x h x d) 185 x 103 x 115 cm 235 x 143 x 115 cm

net weight 135 kg 175 kg

gross weight (crate) 195 kg 245 kg

PnEUMAtiC FEAtURES

air pressure 6 bars 6 bars

air consumption 3 m³/h 3,5 m³/h

ELECtRiCAL FEAtURES

belt motor roller three phase 230/400 V50 Hz 95 W

three phase 230/400 V50 Hz 95 W

SHEET FEED

SCREEN PRINTING

*


mO 255- for printing on flat items included between 0 and 40 cm thick and in a maximum format of 25 x 50 cm- of modern an flexible design, and it complies with European standard in force.


T E C H N O L O G I C A L & I N D U S T R I A L S O L U T I O N S S C R E E N P R I N T I N G

• pneumatic clamping of the frame (maintained this in the event of air or electrical failure)• precise adjustment and display of squeegee’s pressure

This semi-automatic machine for printing on flat items included between 0 and 40 cm thick is of modern and flexible design, and it complies with European standard in force. it prints in a maximum format of 25 x 50 cm.

• pneumatic clamping of the squeegee and the flood bar


• moving print table, with or without vacuum grooved tray, revolving tray... (consult us)

• control panel separated from the frame

• smooth and silent operation

• precise adjustment and display of squeegee’s angle

• electrical adjustment of the off contact given by the vertical travel of the table

MO 255


Parts and labour are warrented on the MO 255. it is supplied with an electrical pedal, a squeegee and bottom knife set, and a user manual.



nominal printing format : 25 x 50 cm

item thickness : 0 to 40 cm

maximum external dimensions of screen : 50 x 70 cm

minimum left and right garages : 4,5 and 6,5 cm

minimum / maximum tray height to the floor : 70 - 110 cm

length of the scraper supplied : 30 cm

“out of contact” : from 0 to 2 cm

dimensions of the table : 40 x 60 cm

OvERALL diMEnSiOnS

overall dimensions d x w x h (without panel) : 141 x 115 x 156 cm

net weight : 325 kg

gross weight (crate) : 420 kg


supply voltage : 230 V single phase

output : 200 W

mains power cord cross-sectional area : 3 G 1,5 mm²


pressure : 6 bars

flow rate : 5 m³ / h


Operating sound level : 80 decibels max.


MO 255

IMP.

TIFL

EX 1

1.02

.201

3 - N

on c

ontra

ctua

l pic

ture

s

SCREEN PRINTING

*


mO 406- for printing on flat items included between 0 and 40 cm thick and in a maximum format of 40 x 60 cm- of modern an flexible design, and it complies with European standard in force.



This semi-automatic machine for flat items printing, of thickness between 0 and 40 cm, has a flexible, modern design, in compliance with applicable European standards. it prints up to a max. format of 40 x 60 cm.

• pneumatic clamping of the squeegee and flood bar • pneumatic clamping of the frame (clamping maintained in the event of air or electricity failure)• accurate setting and display of the squeegee pressure

MO 406

• control panel separate from the frame• smooth, silent operation

• accurate setting and display of the squeegee’s angle• electrical setting of the off-contact given by the vertical displacement of the table• moving print table, with or without vacuum grooved tray, revolving table, etc... (please contact us)



nominal print format : 40 x 60 cm

screen max. outer dimensions : 60 x 85 cm

min. left and right garages : 6 cm

max. part thickness : 40 cm

length of squeegee supplied : 42 cm

“off-contact” : from 0 to 2 cm

table dimensions : 60 x 70 cm

OvERALL diMEnSiOnS

overall dimensions d x w x h (without panel) : 182 x 170 x 161 cm

net weight : 620 kg



power supply voltage : 230 V single phase

installed power : 600 W

cross-section of mains cable : 3 G 1,5 mm²


pressure : 6 bars

rate : 5 m³ / h


sound level during operation : 80 decibels max.

Parts and labour are warrented on the MO 406. it is delivered with an electric foot pedal, a set of squeegee and scrapper blade and user’s manual.


IMP.

TIFL

EX 1

1.02

.201

3 - N

on c

ontra

ctua

l pic

ture

s


MO 406

SCREEN PRINTING

*


ULTRA VIOLET DRYING TUNNEL- teflon glass antistatic belt resisting to heat- conveyor speed from 10 to 40 m/mn- speed controlled by digital display- equiped with a separate cooling unit: tube and printed substrate.





IMP.

TIFL

EX 1

1.02

.201

3 - N

on c

ontra

ctua

l pic

ture

s

U.v. dRYinG tUnnEL 80 100 120

MEChAniCAL CARACtéRiStiCS

drying maxi width : 80 cm 100 cm 120 cm

conveyor width : 80 cm 100 cm 120 cm

opening maxi width : 88 cm 108 cm 128 cm

ventilation diameter : Ø 12,5 cm Ø 12,5 cm Ø 12,5 cm

OvERALL diMEnSiOnS

overall width : 130 cm 150 cm 170 cm

overall length : 276 cm 276 cm 276 cm

entry or exit element length : 90 cm 90 cm 90 cm

overall height : 132 cm 132 cm 132 cm

conveyor standard distance from floor : 90 cm 90 cm 90 cm


gross weight (on a wooden base) : 550 kg 600 kg 650 kg

ELECtRiCAL CARACtERiStiCS

total needed power when starting : 52 kW 63 kW 80 kW

380 V intensity on 2 live wires when starting : 75 A 90 A 115 A

feeding cables section 400 V : 4 x 10 mm² 4 x 10 mm² 4 x 10 mm²

the ultra violet drying tunnel is dedicated to dry rapidly U.v. inks.

This equipment is manufactured in 4 standard widths : 80, 100, and 120 cm.

• Working process Printed materials are conveyed by a conveyor at a higher speed than 10 m/mn, and are exposed to the radiance of a U.V. ray tube which dries them by polymerisation in a spit second.

• Characteristics - tubes lineic power : 120 W/cm (300 W/inch) - possible tubes low power working (2 positions 100 % and 50 % of the lineic power) - teflon glass antistatic conveyor resisting to heat (250°C) - conveyor speed variation (from 10 to 40 m/mn) - speed controlled by a digital display - separate cooling of the tubes and printed materials - on request, it is possible to add an extra cooling element - this tunnel does not need a constant control : any functionning failure leads to the tube stop and activates a sound warning.

Exceptional by its design and its power, the Uv drying tunnel is also appreciated for its easy use.

ULTRA VIOLET DRYING TUNNEL

SCREEN PRINTING

*


jET AIR DRYING TUNNEL- stable and resistant teflon-glass blanket- electronic speed from 0,1 to 15 m/mn- parallelism and belt conveyor tension adjustments- temperature regulation controlled by thermostat- easy access to control panel- large pipes (200 mm) to exhaust solvent fumes





IMP.

TIFL

EX 1

1.02

.201

3 - N

on c

ontra

ctua

l pic

ture

s

ShEEt FEEd SF 80 SF 120

MEChAniCAL FEAtURES

belt width 800 cm 1 200 cm

maximum belt speed 25 m/mn 25 m/mn

maximum dimensions of sheet for printing 1050 x 750 mm 1150 x 1500 mm

minimum margin on jogging side 20 mm 20 mm

maximum thickness of sheet for printing 10 mm 10 mm

maximum weight of sheet for printing 3 kg 3 kg

maximum theoretical rate (cycle start pedal locked) 780 cycles/hour 500 cycles/hour

diMEnSiOnS

overall dimensions (l x h x d) 185 x 103 x 115 cm 235 x 143 x 115 cm

net weight 135 kg 175 kg

gross weight (crate) 195 kg 245 kg

PnEUMAtiC FEAtURES

air pressure 6 bars 6 bars

air consumption 3 m³/h 3,5 m³/h

ELECtRiCAL FEAtURES

belt motor roller three phase 230/400 V50 Hz 95 W

three phase 230/400 V50 Hz 95 W

the jet air drying tunnel is mainly used to accelerate the drying of solvent based inks printed on papers, cartons, PvC, plastics in sheets, wood and metal panels.

This material is manufactured in 3 standard widths, from 80 cm to 120 cm opening. On request, we can manufacture other sizes.

• Modular design The modular design with two elements of 2 m length, allows the realization of an evolutive assembly, adapted to the users' requirements. Each element is controlled separately by the console situated inside the entry element. Our standard model (1) is composed of one entry, one heating element, one cooling element and of one exit. Additional heating, cooling and UV or IR element can be easily added to this unit.

• Working process Drying is obtained by the action of hot air jets on printed materials. Each element contains a powerful turbine which ensures the quick air circulation. In the heating element, air is heated when passing on reinforced resistances. It is then recycled in order to realize energy savings and the appropriate setting on the conveyor of the thinnest sheets. Each element is equipped with an extracting turbine. • Characteristics - stable and resistant teflon-glass blanket - electronic speed variation from 0,1 to 15 m/mn (please consult us for other reduction ratios) - parallelism and belt conveyor tension adjustments - temperature regulation controlled by thermostat - easy access to main switch and emergency knobs - large diameter ducts (200 mm) to exhaust solvent fumes

Thanks to its strong construction, its meticulous thermal insulation, its soundless functioning, this JA drying tunnel is a particularly homogeneous and efficient equipment in compliance with the current requirements of hygiene and energy savings.

standard unit unit cold hot UV entry

JET AIR DRYING TUNNEL

SCREEN PRINTING

*


DRYING RACkS- stiff and monobloc frame- equipment rests on four rubber wheels- plated racks for easy counting



IMP.

TIFL

EX 1

1.02

.201

3 - N

on c

ontra

ctua

l pic

ture

s


dRYinG RACkS 70 x 100 85 x 125

ChARACtERiStiCS

maxi useful size :mini useful size :

70 x 100 cm9 x 18 cm

85 x 125 cm9 x 18 cm

interval between 2 racks : 1,6 cm 1,6 cm

number of racks : 60 60

height of the last rack horizontal :upper position :

164 cm230 cm

164 cm245 cm

maxi drying temperature : room temperature room temperature

OvERALL diMEnSiOnS

dimensions : 75 x 108 x 170 cm 90 x 132 x 170 cm



tROLLEYS 31 52 60

ChARACtERiStiCSmaxi useful size :mini useful size :

70 x 100 cm9 x 18 cm

85 x 125 cm9 x 18 cm

70 x 100 cm9 x 18 cm

85 x 125 cm9 x 18 cm

70 x 100 cm9 x 18 cm

85 x 125 cm9 x 18 cm

interval between 2 racks : 1,6 cm 1,6 cm 1,6 cm 1,6 cm 1,6 cm 1,6 cm

number of racks : 31 31 52 52 60 60

height of the last rack- horizontal :- upper position :

95,2 cm159 cm

95,2 cm173 cm

146,2 cm210 cm

146,2 cm225 cm

164 cm230 cm

164 cm245 cm

maxi drying temperature : 200°C 200°C 200°C 200°C 200°C 200°C

OvERALL diMEnSiOnS

dimensions 75 x 108 x 97 cm 90 x 132 x 97 cm 75 x 108 x 152 cm 90 x 132 x 152 cm 75 x 108 x 164 cm 90 x132 x 164 cm

net weight : 120 kg 160 kg 140 kg 190 kg 150 kg 200 kg

gross weight (open crate) : 160 kg 200 kg 180 kg 230 kg 190 kg 240 kg

On request, we offer special trolleys and drying racks :• 5 cm spacing (30 racks maxi, for items of maxi thickness 4,1 cm)• 7,5 cm spacing (20 racks maxi, for items of maxi thickness 6,6 cm)• number of racks on demand, within the limits indicated hereunder : - 60 for a standard rack or trolley - 30 for a standard rack or trolley with 5 cm spacing - 20 for a standard rack or trolley with 7,5 cm spacing.

Our drying racks feature 60 racks of 70 x 100 or 85 x 125 cm and offer the advantage of minimum overall floor dimensions.

The stiff and monobloc frame is manufactured with welded iron profiles. This equipment rests on four rubber pivoting wheels with a double row of balls for an easy movement even when it is full loaded. The racks are made of welded iron thread protected by zinc plating. An original design of the guides provides a perfect locking which avoids lapping and twisting of the shelves. Two return springs allow the stand in up-right position of each rack. The 2cm interval which separates them in the lower position has been studied to obtain a better air circulation, and consequently a better drying. Furthermore, allied with the rack rigidity, that interval eliminates any risk of blotting with the last printed item when the next rack is loaded.

For oven drying, we offer in the same sizes, 70 x 100 and 85 x 125 cm, trolleys mounted with wast iron wheels. they exist with 31, 52 or 60 racks.

Our drying racks and trolleys are delivered fully assembled and ready to use.


DRYING RACKS

SCREEN PRINTING

*


RH mACHINE- pneumatic clamping of the screen, squeegee and flood bar- perfectly flat perforated honeycomb aluminium plate- automatic or manual vacuum control- transversal and longitudinal table adjustment





IMP.

TIFL

EX 1

1.02

.201

3 - N

on c

ontra

ctua

l pic

ture

s

26 cm

75 cm

Rh machine 2012 3012


maximum print format 200 x 120 cm 300 x 120 cmscreen max. outside dimensions 280 x 180 cm 380 x 180 cmgarage (width) 25 cm 25 cmgarage (height) 15 cm 15 cmdimensions of the table 300 x 164 cm 400 x 164 cmsuction surface 200 x 120 cm 300 x 120 cm

Micrometric adjustmentslongitudinal ± 15 mm ± 15 mm

transverse ± 15 mm ± 15 mm

MEASUREMEntS

height of table 90 cm 90 cmheight of squeege/doctor blade handle 112 cm 112 cmoverall length 346 cm 446 cmmax. depth 290 cm 290 cmmax. height 200 cm 200 cmtop clearance 75 cm 75 cmbottom clearance 26 cm 26 cmnet weight 900 kg 1 000 kggross weight 950 kg 1 050 kg


supply voltage 380 V tri 380 V tri

engine power 1 700 W 1 700 W

electric current requirement 2,5 A 2,5 A


supply air filtered to 40 µ air filtered to 40 µ

the Rh machine (horizontal screen lifting) prints all flat surfaces manually: paper, cardboard, self-adhesives, sheet plastic materials, wood and metal panels etc… up to a thickness of 8 cm. its doctor blade provides regular, high-quality printing whilst reducing the operator’s physical effort. it is supplied with a doctor blade suitable for maximum print format.

• Characteristics:- frame installed from the front of the machine- pneumatic screen clamping- pneumatic clamping of the squeege and the flood bar- micrometric setting of the squeege and the flood bar’s pressure- in lower position, the frame holder assembly is locked by electromagnetic suckers guaranteeing perfect positioning- perfectly flat perforated honeycomb aluminium plate- vacuum controlled by pulse on pedal, or automatic- lifting force adjustable by handles- table adjustable longitudinally and transversally- automatic changeover squeegee/flood bar

RH MACHINE

SCREEN PRINTING

*


ONE ARm PRINTING UNIT- perfectly flat perforated honeycomb aluminium plate- strong pump for vacuum- longitudinal and transversal micrometric setting



BP 3 - 01450 PONCIN - FranceInternational Sales : Tel. +33 (0) 4 74 37 33 80/97 - Fax +33 (0) 4 74 37 33 62 - [email protected] - www.tiflex.com IM

P.TI

FLEX

11.

02.2

013

- Non

con

tract

ual p

ictu

res

OnE ARM PRintinG Unit 60 x 80 80 x 120


maxi printing size : 60 x 80 cm 80 x 120 cm

screen maxi outside dimensions : 90 x 120 x 4 cm 110 x 170 x 6,5 cm

printing table dimensions : 100 x 173 cm 124 x 223 cm

punched surface : 64 x 84 cm 88 x 128 cm

item maxi thickness : 5 cm 5 cm

micrometric regulation :- longitudinal stroke- transversal stroke

2 cm4 cm

2 cm4 cm

supplied squeegee length : 70 cm 90 cm

OvERALL diMEnSiOnS

table average height : 88 cm 88 cm

dimensions on ground p x l : 87 x 146 cm 110 x 196 cm

dimensions on ground p x l : 155 x 180 x 120 cm 180 x 230 x 122 cm




feeding tension : 230 V mono 230 V mono

engine power : 0,85 kW 0,85 kW

absorbed intensity : 6,4 A 6,4 A

The «one arm» printing unit is equipped with a vaccum base and manufactured in 2 maximum printing sizes : 60 x 80 and 80 x 120 cm.

This manual machine can print on any flat surface (papers, cartons, adhesives, plastic sheets, wood and plastic panels, textiles...) up to 5cm thick. Its scraping process ensures printing quality and regularity and reduces the user’s physical efforts. It is supplied with the printing maxi size corresponding squeegee: 70 or 90 cm according to the machine.

• Printing table Its frame in welded steel tube ensures a perfect stiffness and stability. A shelf is set halfway down in order to store ink tins, squeegees... The frame helds the printing table, an aluminium punched panel which is absolutly stiff and withstands any kind of inks and diluters. The table slant facilitates the setting of the item which is kept held by a strong pump. The screen up and down movements automatically control the vacuum situated under the printing table.

• the printing system is composed of parallel and interdependent bars - The first one is hexagonal and bears the screen holder bars which can be separately moved according to the screen sizes.The screen fastening in the slides is reinforced by manual clamping screws with washers in order to prevent frame scratches. - The second one is cylindrical and ensures the longitudinal guiding of the scraping system.

• the scraping system is composed of: • a carriage on which the following elements are set:- 2 diabolo nylon wheels (spol shaped) and 2 cylindrical wheels mounted on ball-bearing to ensure a regular and even sliding.- 2 adjustable nylon stops to raise the screen and lift the squeegee. The squeegee slant may be modified according to the requirement during the printing or the flooding. • a handle which carries the carriage and bears the squeegee holder that can be moved along the handle. • a sliding counterweight with a stop to prevent its fall. On the 60 x 80 cm machine, it is sufficient enough to balance squeegee and screen while on the 80 x 120 cm machine, 2 additional counterweights are set at the end of the parallel bars.

• Adjustments Thanks to the longitudinal micrometric adjustment and to the transversal micrometric adjustments set on each slide of the frame holder, the registration is easy to realize by moving the screen.

the «one arm» printing machine is unanimously appreciated thanks to its numerous possibilities, its easy adjustments and its 1-phase electrical feeding.


ONE ARM PRINTING UNIT

SCREEN PRINTING

*


PRECImA- perfectly flat perforated honeycomb aluminium plate- strong pump for vacuum- longitudinal and transversal micrometric setting




P.TI

FLEX

11.

02.2

013

- Non

con

tract

ual p

ictu

res


Precima is a flat printing machine equipped with a vacuum table. it is manufactured in 2 sizes:40 x 60 and 60 x 80 cm (maxi printing size). it can print on items with a 12 cm maximum thickness for the first model and 14 cm maximum thickness for the second one.

It is characterized by its regulation precision and its easy use. The screen remains horizontal during the setting and the removing of the item. The screen lift is effortless thanks to a return spring.

• Printing table A frame helds the printing table made of punched alloy aluminium. The printing table is perfectly flat and withstand any kind of inks and diluters. A shelf is set halfway down in order to store ink tins, squeegees ... A powerful and soundproof vaccum helds the item in registration. It is controlled by the operator with a treadle.

• Printing system Two screen holders fit the screen sizes, they are articulated on stub axles in order to determine two working positions : - low printing position - high position to set and remove the items. A return spring facilitates the lift. It is adjustable according to the screen weight and the user’s requirements.

• Adjustments Thanks to the longitudinal micrometric regulations and to the transversal micrometric regulations set on each slide of the frame holder, the registration is easy to realize by moving the screen.

PRECiMA 40 x 60 60 x 80


maxi printing size : 40 x 60 cm 60 x 80 cm

screen maxi outside dimensions : 60 x 80 x 4 cm 80 x 120 x 4 cm

printing table dimensions : 78 x 125 cm 100 x 165 cm

perforated surface : 50 x 60 cm 65 x 85 cm

item maxi thickness : 12 cm 14 cm

micrometric regulations- longitudinal stroke- transversal stroke

2 cm4 cm

2 cm4 cm

OvERALL diMEnSiOnS

plate height on ground : 85 cm 85 cm

dimensions on ground p x l : 70 x 99 cm 90 x 146 cm

overall dimensions p x l x h : 102 x 138 x 121 cm 130 x 178 x 135 cm



tEChniCAL ChARACtERiStiCS

feeding : 230 V mono 230 V mono

engine power : 0,85 kW 0,85 kW

absorbed intensity : 6,4 A 6,4 A

PRECIMA

SCREEN PRINTING

*


bENCH COmbINETUVE- U.V. neon tubes- one dry rack- settable temperature




P.TI

FLEX

11.

02.2

013

- Non

con

tract

ual p

ictu

res

Combinetuve is a metalic cabinet for the exposure and drying of silk screen frames up to a size of 60 x 80 cm.

It consists of 2 separate element :

• The exposure part composed of a pneumatic frame, a glass and a suple and UV resistant blankes (deformation up to 7 cm). The vacuum is obtained thanks to a story and silat palet pump.

• The drying part with 3 shelves heated with a turbine and a temperature regulator.

BEnCh COMBinEtUvE 608

MEChAniCAL CARACtERiStiCS

screen maxi size 60 x 80 cm

number of 40 W tubes 8

glass size 70 x 90 cm

OvERALL diMEnSiOnS

dimensions 87 x 133 x 54 cm

feeding 230 V 1-phase


intensity 12 A

SOUnd CARACtERiStiCS

sound level in process 65 decibel maxi

BENCH COMBINETUVE

SCREEN PRINTING

*


COmbINETUVE- U.V. neon lighting tube- light integrator- 3 drying racks- settable temperature




P.TI

FLEX

11.

02.2

013

- Non

con

tract

ual p

ictu

res

Combinetuve is a metalic cabinet for the exposure and drying of silk screen frames up to a size of 120 x 160 cm.

It consists of 2 separate element :

• The exposure part composed of a pneumatic frame, a glass and a suple and UV resistant blankes (deformation up to 7 cm). The vacuum is obtained thanks to a story and silat palet pump.

• The drying part with 3 shelves heated with a turbine and a temperature regulator.

COMBinEtUvE 812 1014 1216


screen maxi size 80 x 120 cm 100 x 140 cm 120 x 160 cm

number of 40 W tubes 9 + 1 inactinic

13 + 1 inactinic

20 + 1 inactinic

maxi capacity 3 screens of 80 x 120 cm

3 screens of 100 x 140 cm

3 screens of 120 x 160 cm

glass size 99,5 x 139,5 cm 119,5 x 159,5 cm 139,5 x 179,5 cm

blanket size 100 cm 100 cm 100 cm

OvERALL diMEnSiOnS

overall dimensions 105 x 140 x 106 cm 125 x 160 x 106 cm 145 x 180 x 106 cm

net weight 200 kg 300 kg 380 kg

gross weight (open crate) 220 kg 330 kg 420 kg

feeding 230 V 1-phase 230 V 1-phase 230 V 1-phase


intensity 12 A 15 A 20 A



COMBINETUVE

SCREEN PRINTING

*


ExPOSURE AND DRYING UNIT- pneumatic under frame- halogen lamp- light integrator- 3 drying racks- settable temperature




P.TI

FLEX

11.

02.2

013

- Non

con

tract

ual p

ictu

res

the combine d’insolation is a compact assembly for both exposure and drying of silk screen frames. it is proposed in 3 sizes for screens up to 120 x 160 cm.

It consists of 3 parts :• The exposure part equiped with an halogen lamp to be used with 2 power levels 2000 and 5000 W; an idle mode (obturator closed) maintains the lamp lightened (reduced power) between 2 exposures.• The pneumatic exposure frame which is composed of an articulated glass (for its internal cleaning) and of a resistant, supple and UV resistant blanker. The vacuum is obtained thanks to a powerful, silent paddle pump which fonctions without oif.• The drying part with 3 shelves, heated with a turbine and 2 resistances of 1300 W each and controled by a settable thermostat (60°C maxi).

The combine d’insolation requires an electrical intallation 400 V 3-phase + earth.

COMBinE d’inSOLAtiOn 812 1014 1216


screen maxi size 80 x120 cm 100 x 140 cm 120 x 160 cm

maxi thickness 5 cm 5 cm 5 cm

glass size 99,5 x 139,5 cm 119,5 x 159,5 cm 139,5 x 179,5 cm

blanket size 100 cm 100 cm 100 cm

blanket dimensions 100 x 139 cm 120 x 159 cm 140 x 179 cm

OvERALL diMEnSiOnS

overall dimensions 106 x 152 x 247cm 126 x 172 x 247cm 146 x 192 x 247 cm

net weight 570kg 750kg 900kg

gross weight (open crate) 640 kg 820kg 980kg


feeding 400 V 3-phase + earth

400 V 3-phase + earth

400 V 3-phase + earth

lamp intensity 400 Vstarting 23 A

working 4A-2000W12 A-5000W

starting 23 A working 4A-2000W

12 A-5000W

starting 23 A working 4A-2000W

12 A-5000W1-phase 230 V pump engine intensity 1,30 A 1,30 A 1,30 A

pump power and discharge 0,25 Kw 6 m³/h 0,25 Kw 6 m³/h 0,25 Kw 6 m³/h



EXPOSURE AND DRYING UNIT

SCREEN PRINTING

*


CHASSICOP mURAL- exposure frame delivered mounted with vacuum pump



IMP.

TIFL

EX 1

1.02

.201

3 - N

on c

ontra

ctua

l pic

ture

s


Chassicop mural is a stable and strong equipment,its finish is perfect and satisfies even the most exacting professionals. it is supplied complete, ready to be set on the wall.

27 cm hors toutencombrement réduit

ChASSiCOP MURAL 80 x 100 100 x 130 130 x 170


screen maxi size : 80 x 100 cm 100 x 130 cm 130 x 170 cm

screen maxi thickness : 7 cm 7 cm 7 cm

glass size : 100 x 130 x 0,8 cm 130 x 160 x 0,8 cm 160 x 200 x 0,8 cm

blanket size : 125 x 145 cm 145 x 175 cm 175 x 215 cm

height of glass in horizontal : 95 cm 95 cm 95 cm

OvERALL diMEnSiOnS

vertical position : 25 x 159 x 172 cm 27 x 187 x 184 cm 27 x 229 x 197 cm

horizontal position : 128 x 159 cm x 169 cm 148 x 187 x 180 cm 179 x 229 x 194 cm


gross weight (open crate) : 250 kg 300 kg 450 kg


feeding tension (mono) : 230 V 230 V 230 V

power pump engine : 0,15 kW 3,3 m³ 0,15 kW 3,3 m³ 0,15 kW 3,3 m³

pump engine intensity : 1,15 A 1,15 A 1,15 A

Chassicop Mural is a pneumatic frame dedicated to expose silk screens and films, offset plates, presensitized printed circuits, photo-films, diazoic papers, ..., by contact

This material with horizontal loading and a blanket which opens, is available in 3 models corresponding respectively to the screen maxi outside dimensions : 80 x 100, 100 x 130 and 130 x 170 cm. This mural setting reduces the overall dimensions in vertical position, in an average proportion of 5 to 1. The mural frame is manufactured with mecano-soldered profiles with dismantling cross bars. The assembly window-mat rotates and can occupy 2 positions spaced of 90° allowing exposure from the front or the bottom of the frame. That assembly is composed of 2 articulated frames which insure a long lasting air tightness : the first one holds the window, the second one is a strong, supple(deformation up to 7 cm) and UV rays resistant. Its opening is facilitated, even for the largest model, by gas jacks. The vacuum is realized by a powerful, silent pump which functions without oil. The vacuum-regulator and vacuum gauge are available on request. Il allows to adjust the vacuum created by the pump. At your convenience, we can make a complete exposure equipment in which the digilume P control unit drives the chassicop vacuum pump.


CHASSICOP MURAL

SCREEN PRINTING

*


HALOGEN LAmP- this halogen exposure lampis equiped with a light integrator




P.TI

FLEX

11.

02.2

013

- Non

con

tract

ual p

ictu

res

The metal halogen lamp is an exposure unit for silk screen frames.

It is composed of 2 elements :• a programmation box positionned on a frame equiped with 4 wheels.• an adjustable height projector with incorporated obturator and ventilation. The halogen lamp is meant to be used with 2 different power levels: 2 000 and 5 000 W. An idle mode (obturator closed) maintains the lamp lightened (reduced power) between 2 exposures. It is adapted to all electrical installations 400 V - 2 phases. Very easily , it can be transformed in a ceiling version. The projector is hanged. For a precise setting of the exposure, the halogen lamp is equiped with a light integrator.

hALOGEn LAMP


lamp height on the ground adjustable from 75 to 125 cm

ground dimensions 47 x 67 cm

maxi total height 150 cm

net weight 80 kg

gross weight (open crate) 135 kg


feeding 400 V - 2 phases

intensity 400 V - 25A


sound level while working. 80 decibels maxi

HALOGEN LAMP

SCREEN PRINTING

*


STENCIL DEVELOPING UNIT- unit has enables the processing of silk screens after exposure


S I L k S C R E E N & D I G I T A L P R I N T I N G


IMP.

TIFL

EX 1

1.02

.201

3 - N

on c

ontra

ctua

l pic

ture

s

stencil developing unit 100 x 130 cm 130 x 170 cm 180 x 220 cm


format d’écran maxi : 100 x 130 cm 130 x 170 cm 180 x 220 cm

maxi opening : 110 x 150 cm 126 x 180 cm 176 x 236 cm

OUtSidE diMEnSiOnS

overall dimension : 81,5 x 170 x 205 cm 81,5 x 200 x 220 cm 100 x 245 x 260 cm


gross weight (open crate) : 225 kg 330 kg 475 kg


mains : 220 V mono 220 V mono 220 V mono

On request and after study, we can manufacture special sized developping units.

The stencil developing unit has enables the processing of silk screens after exposure.

The stencil developing unit is manufactured in 3 standard models respectively corresponding to the following maxi outside dimensions of silk screens : 100 x 130 cm, 130 x 170 cm and 180 x 220 cm.

It is composed of two separate parts :• the frame built in rigid PVC, equipped with one shelf• the metal frame• the water tub, also build in rigid PVC, composed of a spread-luminous panel and white lamps. It insures an efficient control.

Stencil developing unit is also equipped with an adjustable and two sliding racks which stalls screens.


STENCIL DEVELOPING UNIT

SCREEN PRINTING

*


SQUEEGEE SHARPENER AR 145- right sharpening for all type of normal squeegee- interchangeable cutting blades- horizontal cutting





IMP.

TIFL

EX 1

1.02

.201

3

the AR 145 sharpening machine complies with CEE 89/392 standard. Parts and labour are guaranteed for 6 months.

Compatible with all standard types of serigraphy blade, the AR 145 blade sharpening machine achieves a straight cut for all blades on standard screen printing machines.

The cutterblock assembly is in the form of a distributor unit consisting of 10 razor blades, guided by a cross rail and driven by a belt. The operator has total security thanks to dual controls.

MEChAniCAL ChARACtERiStiCSmaximum sharpening length : 1 450 mm

minimum blade thickness : 3 mm

maximum blade thickness : 13 mm

blade hardness : between 60 and 100° Shore

type of cut : straight

depth of cut (thickness of the chip) : 0,7 mm mini

MEASUREMEntSoverall dimensions (l x h x d) : 232 x 130 x 61 cm

net weight : 80 kg


ELECtRiCAL ChARACtERiStiCStotal power : 0,6 kW

power supply : 220 V mono

current : 3 A

SOUnd ChARACtERiStiCSSound level during operation : max. 60 decibels

SQUEEGEE SHARPENER

SCREEN PRINTING

*


PNEUmATIC AUTOmATIC wASHING UNIT- airtight manufactured, uses no electricity but only compressed air




P.TI

FLEX

11.

02.2

013

- Non

con

tract

ual p

ictu

res

automatic ink washing SR 120/60 SR 140/60 SR 200/100 SR 250/100


maxi frame size: 120 x 140 cm 140 x 200 cm 200 x 250 cm 250 x 300 cm

nozzles number: 34 44 68 64

solvent tank: 54 l 54 l 94 l 94 l


washing air consumption: 33,6 m³/h 72 m³/h 102 m³/h 112 m³/h

blowing air consumption: 95 m³/h 110 m³/h 110 m³/h 152 m³/h

pressure: 8 bars 8 bars 8 bars 8 bars

OvERALL diMEnSiOnSoutside dimensions p x l x h: 60 x 240 x 220 cm 60 x 300 x 240 cm 60 x 351 x 300 cm 60 x 404 x 350 cm

net weight: 250 kg 390 kg 570 + 100 kg 650 + 100 kg

gross weight: 270 kg 410 kg 590 + 120 kg 700 + 100 kg

this pneumatic automatic washing unit is airtight manufactured, uses no electricity but only compressed air.

The pneumatic automatic washing unit is completly manufactured in stainless steel. It is equipped with an extracting screen holder in order to facilitate its loading. Inside the tank, 2 washing ramps slide on each side of the screen holder. This movement alongside the screen washing stand is obtained by the outside movement of a magnetic field. The solvent is placed under pressure by a pneumatic pump. The 2 washing ramps, equipped with nozzles, can be oriented in order to oppose solvent jets to the ramps movements. Fan-shaped, they softly wash the most fragile screens. This material is tightly closed even during the door opening. A compressed air curtain stops the solvents emanations during the screens loading and unloading operations.

The automatic pneumatic ink washing stand is manufactured in 3 versions : • L washing unit (as described above) • LS washing and blowing unit (an air circulation drains the screen) • LRS washing,rinsing and blowing unit (a clean solvent rinsing completes the washing cycle). All these machines are equipped with stainless steel tanks, meant to store the solvents. They are compatible with the solvent recycling unit with removable tanks (see corresponding documentation). L and LS models are equipped with one tank, LRS models with 2 tanks (cleaning and rinsing solvents).

this material is very efficient, its functioning is completly safe and tight.

PNEUMATIC AUTOMATIC WASHING UNIT

mANUAL PNEUmATIC wASHERFitted with:- two different brushes- a pneumatic pump with Teflon membrane - a regulating filter with pressure gauge


SCREEN PRINTING

*




this equipment is used to clean screens manually, under optimum safety conditions for the operator. By simply re-using filtered solvents, it also protects the workplace environment and allows savings to be made. it requires no electrical connection and operates from a compressed air supply.

The machine has two brushes, each with a central solvent feed. Chemical and manual actions combine to give more effective washing. Solvents are distributed by a pneumatic pump with a Teflon membrane: the system is also fitted with a regulating filter and pressure gauge.

After the washing operation, the solvents descend by gravity into a purification and storage tank, where they are purified ready for use in a new cycle.

Washing can be completed by flushing with clean solvents.

Removable covers retain solvent vapours within the tank. A flue, optionally linked to a mechanical extraction system, takes vapours to the exterior.

in the interests of operator safety, the equipment requires no electrical connection and operates on compressed air only.

MAnUAL PnEUMAtiC WAShER SM 100* SM 150* SE 200*


Maximum screen size 80 x 80 cm 80 x 120 cm 140 x 180 cm

Ø of extraction pipe Ø 20 cm Ø 20 cm Ø 20 cm

diMEnSiOnS

Overall dimensions d x w x h 60 x 100 x 190 cm 75 x 150 x 250 cm 80 x 200 x 250 cm

Net weight 105 kg 150 kg 185 kg

Gross weight 125 kg 180 kg 220 kg


Air consumption 8.4 m³/h 8.4 m³/h 8.4 m³/h

Operating pressure 2 to 3.5 bar 2 to 3.5 bar 2 to 3.5 bar

•SM = front loading, SE = front and side loading

IMP.

TIFL

EX 1

1.02

.201

3 - N

on c

ontra

ctua

l pic

ture

s

MANUAL PNEUMATIC WASHER

SCREEN PRINTING

*


FRAmES AND SCREENS- complete range of different frames



IMP.

TIFL

EX 1

1.02

.201

3 -

Non

con

tract

ual p

ictu

res

We manufacture a complete range of different frames. in order to answer any requirement, we offer bare frames, pre-sensitised or finished screens.

• Bare frames - in aluminium : they offer a very good dimensional stability and are very light. They are rustproof and withstand water and solvents. The standard outside dimensions increase by 10 cm steps. On request, we manufacture any shape, section and size. - in wood : they are still commonly used. The standard outside dimensions increase by 10 cm steps. On request, we manufacture any shape, cross section and particular sizes.

• Pre-stretched screens Our stretching department manufactures the above mentionned frames straight or edge stretched with a complete range of meshes from 18 up to 200 mesh/cm in nylon* or polyester, white, or coloured. We also restretch used frames, provided they are not damaged. Thanks to high performance equipment, we also supply high-tech pre-stretched screens in 2 special aluminium sections.

• Special screens We can manufacture special frames in the most various shapes : curved, round, excentered, tubular... and with different sections : metal corners, reinforcing, grooves, separations...

• Finished screens According to the prints, we expose our screens either coated with our emulsions or mounted with our films. The finished screens, reinforced and protected with adhesive tapes are supplied ready to use. We manufacture the screens and typo in compliance with your documents or with positives realized by us.

• Custom works Our production studio, which is equipped with CAD workstation, handles the drafting and implementation of the most complex artwork. Using your files (PC compatible on formats AI, EPS, PDF and BMP high-definition or DXF), we can enlarge, reduce, multiply, inverse, copy, select colours, retouch, etc. For large formats we do the artwork on film.

* Polyamide fabrics (Nylon) are supplied on request.


FRAMES AND SCREENS

SCREEN PRINTING

*


FAbRICS- complete range from 10 to 180 mesh/cm of polyester fabrics (Tergal® and polyamid Nylon®) specially designed for silk screen printing.

SUPPLIES FOR SILk SCREEN



FABRICS

IMP.

TIFL

EX 1

1.02

.201

3

From 10 to 180 yarns/cm, we offer a complete range of polyester fabrics (tergal® and polyamid nylon®) specially designed for serigraphic printing.

Our fabrics are produced using yarn diameters that are rigorously constant and perfectly controlled. Extremely regular weaving is essential for obtaining quality prints and is guaranteed by the use of the most modern looms. The large quantities of fabric we process allow us to provide you with one of the best quality/price ratios on the market. All our fabrics are monofilament and have been heat stabilised. They are highly resistant to water, solvents, oxidants and chlorinated products. Print work can be removed and the fabric can be used several times.

• Polyester fabrics These are characterised by a high tear resistance, an above-average even extensibility in the 2 directions and a reduced loss of tension. They are abrasion-resistant and waterproof (0.4 % at 20°C and 65% relative humidity).

• Polyamide fabrics (specially manufactured on request) These are completely abrasion-resistant. They are more permeable than polyester fabrics (4.4 % at 20°C and 65 % relative humidity). These fabrics are suitable for printing on irregular surfaces. They are recommended for direct printing on ceramics.

• Fabric dyeing Dyeing the fabric enhances the screen exposure precision and therefore the print quality. All our fabrics are white or dyed.

white polyester yellow polyester

• new fabric denomination:18 - 250 W PW : - number of yarns per cm18 - 250 W PW : - film diameter in microns18 - 250 W PW : - colour of fabric W = white Y = yellow18 - 250 W PW : - weft of fabricPW : - taffeta 1/1

The width is given by way of an indication and may vary several centimeters.On request, we can supply others quality and stitch material (ex : polyamid)

• Characteristics of polyester fabrics (tergal®)

Description yams/cm Name width/

cm Ref. Euro

White polyester 18 18-160W-PW 115 2850436X 23.25



White polyester 43

43-80W-PW 115 2853536X 24.05

43-80W-PW 158 2853539X 25.60

43-80W-PW 212 2853545X 38.30

Yellow polyester 43 43-80Y-PW 158 2873539X 26.90

White polyester 49 49-70W-PW115 2853936X 24.05

158 2853939X 25.60





White polyester62 62-64W-PW 115 2854436X 25.15

62 62-64W-PW 158 2854439X 28.90



158 2854839X 38.10


White polyester 77 77-55W-PW

115 2855036X 28.90

158 2855039X 38.40

212 2855041X 50.25

Yellow polyester 77 77-55Y-PW158 2875039X 39.40

212 2875041X 52.60


158 2855639X 40.10


212 2875641X 57.65

Description yams/cm Name width/

cm Ref. Euro


158 2856039X 40.10


212 2876041X 57.65


White polyester 120 120-34W-PW

115 2856836X 35.70

136 2856837X 41.40

158 2856839X 45.20

212 2856841X 60.95

Yellow polyester 120 120-34Y-PW

115 2876836X 38.10

158 2876839X 46.70

212 2876841X 65.60


158 2856809X 45.20


212 2876811X 65.60




212 2877641X 82.65




White polyester 165 165-34W-TW 115 2858436X 64.65

Yellow polyester 165 165-34Y-TW 158 2878439X 87.35

Yellow polyester 180 180-31Y-TW 158 2878559X 90.00

SCREEN PRINTING

*


SCREEN mANUFACTURING PRODUCTS



1. diazo compound photosensitive solutions

• diazo 19 S (for solvent-based inks) Supplied in 0.9 l pots, boxes of 6 x 0.9 l pots and 4.5 l buckets with diazocompound sensitiser dose, this solution can be used in either thick or thin layers. Good definition, resists solvents, also suitable for small printing runs with water-based inks. Stripped off with cold water. The active de-engraving agents (Oxygel, Oxysol, Oxylic) are required for its retrieval, followed by finishing with high pressure de-engraver. Stored in the dark, screens coated with diazo 19 S can be kept for 4 months at 20°C.

• diazo 149 S (for solvent-based inks) Supplied in 0.9 l pots, boxes of 6 x 0.9 l pots and 4.5 l buckets with diazocompound sensitiser dose, this solution can be used in either thick or thin layers. Excellent definition, full resistance to all solvents. Stripped off with cold water. The active de-engraving agents (Oxygel, Oxysol, Oxylic) are required for its retrieval, followed by finishing with high pressure de-engraver. Stored in the dark, screens coated with diazo 149 S can be kept for 4 months at 20°C.

• diazo 19 t (for water-based inks) Supplied in 0.9 l pots, boxes of 6 x 0.9 l pots and 4.5 l buckets with diazocompound sensitiser dose, this solution can be used in either thick or thin layers. Reasonable resistance to water-based inks, suitable for small printing runs with solvent-based inks. Stripped off with cold water. Retrieval is less easy : the active de-engraving agents (Oxygel, Oxysol, Oxylic) are required, followed by the use of a powerful de-engraver (P > 100 bars). Stored in the dark, screens coated with diazo 19 t can be kept for 4 months at 20°C.

2. diazocompound photopolymer composite photosensitive solution (these solutions are insolated with a halogen lamp)

• USt (universal but more suitable for solvent-based inks) This composite emulsion, supplied in 0.9 l pots, boxes of 6 x 0.9 l pots and 4.5 l buckets with sensitiser dose, is a multi-purpose high-definition product. Stripped off with water. The screen is retrieved with our de-engraving agents Oxygel, Oxysol or Oxylic, followed by finishing with high pressure de-engraver. Stored in a dark, dry room at a temperature of 20°C, the screens sized with USt can be kept up to 20 days.

• 200 S (for solvent-based ink) This composite emulsion, supplied in 0.9 l pots, boxes of 6 x 0.9 l pots and 4.5 l buckets with sensitiser dose, is a high-definition product. Stripped off with water. The screen is retrieved with our de-engraving agents Oxygel, Oxysol or Oxylic, followed by finishing with high pressure de-engraver. Stored in a dark, dry room at a temperature of 20°C, the screens sized with 200 S can be kept from 1 to 2 months.

• 200 t (universal) This composite emulsion, supplied in 0.9 l pots, boxes of 6 x 0.9 l pots and 4.5 l buckets with sensitiser dose, offers good resistance to water-based inks. It is particularly intended for thick coatings. It can also be used with plastisols and some solvent-based inks. Stripped off with cold water. Retrieval is less easy: the de-engraving agents (Oxygel, Oxysol or Oxylic) are required, followed by the use of a powerful de-engraver (P > 100 bars). Stored in the dark, the screens coated with 200 t can be kept for 15 days.

• 300 t (universal) This composite emulsion, supplied in 0,9 l pots, boxes of 6 x 0,9 l pots and 4,5 l backets with sensitiser dose, is a high-definition product. Stripped off with cold water. The active de-engraving agents (Oxygel, Oxysol or Oxylic) are required for its retrieval, followed by finishing with high pressure de engraver. (P > 100 bars). Stored in the dark, the screens coated with 300 t can be kept for 4 months.

3. Additional screen manufacturing products

• Prep’écran (ScreenPrep) Supplied in 5 l jerrican, this degreasing agent prepares the fabric fibres ready for coating with the solutions and assembly of the capillary films.

4. Additional products for reinforcing and retouching

• Reinforcing solution Supplied in 1 l pots, it is used for retouching, reinforcing and sealing screens. Brushed on, fully resistant to all solvents, it can be removed with the traditional de-engraving products.

• Filling solution Xd 153 Supplied in 5 l jerricans, it is recommended whenever large areas need to be blocked up. Applied with a spatula or hollow sizing doctor blade. It is odourless, dries quickly, resists all solvents and easily removed with water.

• Résistalo (Wateresist) solution Supplied in 1 l boxes, it is used for retouching and reinforcing screens which must resist inks diluted with water. Applied with a brush or spatula, its dries quickly and is removed using a solvent.

SCREEN MANUFACTURING PRODUCTS

• blue pore stopper Supplied in 5 l jerricans, it is used for retouching, reinforcing and waterproofing screens. Brushed on, it dries rapidly, is fully resistant to all solvents and can be removed with the traditional de-engraving products. It is coloured blue to simplify application.

5. Additional products for de-engraving

• Oxygel De-engraving agent supplied in 5 l buckets, this ready-to-use gel is brushed on. Most solutions and photosensitive films are solubilised in just 5 minutes. Non-polluting, chlorine-free and biodegradable, it meets all requirements of the hygiene and safety committees.

• Oxysol De-engraving agent supplied in 100 g and 500 g bottles and in 25 kg drums as a concentrated salt. 100 g of powder are dissolved in water to produce 5 to 10 l of ready-to-use liquid, depending on the desired degree of efficiency. Non-polluting, chlorine-free and biodegradable, it meets all requirements of the hygiene and safety committees.

• Oxylic Liquid, ready-to-use de-engraving agent, supplied in 5 l jerricans. Most solutions are solubilised in just three to five minutes. Non-polluting, non-flammable and harmless, this product meets all requirements of the hygiene and safety committees.

• Concentrated de-engraving agent Supplied in 5 l jerricans, this economical product is intended for manual or automatic de-engraving of the screens. It is diluted with water (1 volume of concentrated product for 20 volumes of water). Most solutions and photosensitive films are solubilised in just three to five minutes.

• Finisher 4886 Supplied in 1 l bottles, it is useful if you do not have a de-engraver. It is used in combination with de-engraving agents, by dissolving any undesirable traces remaining on the fabric.

6. Products for the treatment of ghost images

• Oxymage and Solvymage Oxymage supplied in 5 l buckets is a high viscosity product used to eliminate ghost images and prevent fabric yellowing due to the use of diazocompound sensitiser. Its application on a screen lasts approximately 12 hours (overnight). The action of Oxymage is completed by application of Solvymage supplied in 5 l jerricans.

• Oxypâte and Solvypâte Supplied in 5 l jerricans, Solvypâte prepares the fabric for the fast and efficient action of Oxypâte (maximum 15 to 30 min.). Supplied in 5 l buckets, Oxypâte is a product used to eliminate ghost images.

• Applicator brush Nylon brush used to apply all products for the treatment of ghost images.

7. Miscellaneous supplies for screen manufacture:

• Polyurethane adhesive Two-component polyurethane base used for gluing silkscreened fabrics stretched over wooden or metal frames, it is supplied in 830 g pots plus hardener in 170 g pots. Good resistance to solvents (cleaning) and hot water (stripping).

• hollow sizing doctor blade Made from light extruded alloy, supplied in the requested length, the hollow sizing doctor blade has 2 removable plastic ends for easy cleaning. Its round, uniform profile ensures high quality sizing at constant thickness.

• Polyurethane foam Supplied in 190 x 140 cm sheets 15 mm thick, it ensures even placage during screen exposure if there is no pneumatic chassis.

• Polynoir plastic tape Available in rolls 66 m long and 4 widths: 25, 38, 50 and 75 mm. Guarantees excellent screen watertightness. The polypropylene support is extremely resistant to physical and chemical stress.

• Polytoil adhesive tape Available in rolls 50 m long and 4 widths: 25, 38, 50 and 75 mm. It offers the same mechanical strength characteristics as Polynoir but is more flexible and displays greater adherence when used with screen washers.

• Silver adhesive tape Applied directly on the fabric, on the outer side of the screen, it stops any “leaks”. Fully resistant to solvents and thinners. Available in rolls 66 m long and 2 widths: 25 and 38 mm.


characteristics

diazo 19 S

diazo 149 S

diazo 19 T

U.S.T.

200 S

200 T

300 T

Graphic HU

Graphic PES

Vitrum HHU

Textil HT

viscosity at 20°C 6 Pa.s 7,5 Pa.s 6 Pa.s 8 Pa.s 20 Pa.s 18 Pa.s 7,75 Pa.s 13 Pa.s 3 Pa.s 35 Pa.s 18 Pa.s

fromfinition *** **** **** ***** ***** ***** ***** ***** *** ***** ****

resolution *** **** *** ***** ***** ***** ***** ***** *** **** ****

resistyearce to solvents **** **** ** **** ***** **** **** ***** ***** ***** ****

resistyearce to water ** * **** ** ** ***** ***** **** ** **** *****

from-engraving **** **** ** **** **** **** **** ***** ***** ***** ****

approximate lifetime of the sensitised emulsion at 20°C

4 months 4 months 4 months 1 months 1 months 1 months 1 months 1 months - 1 months 1 months

approximate lifetime of the non-sensitised emulsion

2 years 2 years 2 years1 year to une tem-

pérature < to 20°C

1 year 1 year 1 year 1 year 2 years 1 year 1 year

approximate lifetime of the coated screen stored at 20°C

4 months 4 months 4 months 20 dayss 1 to 2 months 15 dayss 4 months 15 dayss - 15 dayss 15 dayss

recommen-fromd mesh

from 50to 165

fibres/cm

from 50to 200

fibres/cm

from 10to 135

fibres/cm

from 40to 200

fibres/cm

from 40to 200

fibres/cm

from 30to 165

fibres/cm

from 30to 165

fibres/cm

from 43to 200

fibres/cm

from 62to 200

fibres/cm

from 12to 120

fibres/cm

from 34to 120

fibres/cm

8. Solution selection table

Remarks:• several characteristics are assessed on a quality scale ranging from 1 star for the worst result to 5 stars for the best.• the definition of a coated solution is its ability to reproduce a geometric shape such as a circle.• the resolution of a coated solution is its ability to reproduce the finest possible line.• diazo 19 S solution is a good multi-purpose product.• diazo 149 S solution is appreciated for its fineness.• 200 S is a very high performance universal solution, intended for solvent-based inks.• 200 t is a very high performance universal solution• 300 t is an excellent multi-purpose solution. Very good resistance to water-based inks, resists plastisols and some solvent-based inks.

IMP.

TIFL

EX 1

1.02

.201

3 - N

on c

ontra

ctua

l pic

ture

s


SCREEN MANUFACTURING PRODUCTS

SCREEN PRINTING

*


mISCELLANEOUS PRODUCTS- for ink preparation- printing supplies- cleaning supplies- hygiene supplies

ADDITIONAL PRODUCTS, mISCELLANEOUS



P.TI

FLEX

25.

02.2

013

- Non

con

tract

ual p

ictu

res

Miscellaneous supplies for ink preparation • Empty pots, empty buckets (with covers) 1 l (boxes of 14) empty pots and 5 l (boxes of 6) empty buckets made from black polyethylene, to prepare ink/thinner mixtures easily. • Mixing cups (with covers) Sold in packets of 25, made from transparent polypropylene, resist all solvents. Flexible and unbreakable, they contain 250 and 550 ml. Extremely useful when mixing and diluting with graduations printed on the side. • Wooden sticks Two models suitable for the mixing cups, 1 l empty pot and 5 l empty bucket. A very useful accessory when mixing in the ink boxes. • Mixing knives Two models suitable for the 1 l empty pot and 5 l empty bucket. Stainless steel blade, 150 or 250 mm long. Used to mix and prepare inks. • 8 kg ink weight scale precision 0,1 A must for all silkscreening workshops. Simple, practical and reliable, range 0 to 8000 grams, accurate to the nearest gram. • Pantone® colour chart Tiflex manufactures and sells numerous types of ink compatible with the “Pantone tinting guide”. This guide includes a selection of 1000 hues from the Pantone colour chart. The formulation of each hue is given, in order to quickly mix these 1000 Pantone hues. Miscellaneous printing supplies • Spatulas Available in dimensions of 100 and 140 mm wide, our stainless steel spatulas have rounded corners to avoid tearing the fabric. • Stop-Sec drying inhibitor (freon-free) Sold individually or in boxes of 6 x 500 ml aerosol sprays. By spraying on this drying inhibitor before the end of each print run, the next job can be immediately restarted without cleaning the screen and without modifying the ink characteristics. • Aerofix S (freon-free) Sold in boxes of 12 x 600 ml aerosol sprays, this adhesive is especially designed to hold the fabrics while printing. • takter 1 Sold in boxes of 12 x 500 ml aerosol sprays, water based adhesive to fix fabric on the printing board. • PvC shims for feeding Packed in bags of 25 shims, thickness 0.4 and 1 mm, they make it easier to position the printed sheets. • temperature indicators Packed in bags of 30 strips, they indicate temperatures from 138 to 188°C.

Miscellaneous cleaning supplies • Clean cloths Delivered in 10 kg bags. • Cellulose wadding Rolls of approximately 1500 precut sheets, dimensions 35 x 29 cm, supplied in packs of 2.• Cleaning towels Delivered in 72-towel containers or in boxes of 6 containers. They are pre-impregnated with a cleaning solution. • humidifier can, 1.9 l and 3.8 l The cleaning solvent is quickly applied on the cloth or the wadding with this practical can.Miscellaneous hygiene supplies • high protection cream Supplied individually or in boxes of 12, in 240 ml aerosol sprays, this cream protects the hands and forearms from inks and solvents. • Protective gloves Offering full protection against solvents, they protect the hands and forearms. • disposable latex gloves Packed in boxes of 100 gloves, for hand protection. • Gel soap In 5 l cans, cleans any traces of ink on the hands whilst softening the skin. Biodegradable. A dispenser pump and wall support are also available for this soap can.

MISCELLANEOUS PRODUCTS

*

SCREEN PRINTING

*


SQUEEGEES & FLOOD bARS- complete range of flood bars suitable for the various printing systems and most existing machines


S C R E E N P R I N T I N G66

mm

77 m

m

Flood bars

We propose a complete range of flood bars suitable for the various printing systems and most existing machines. they are cut to the required length. Unless specified in the order they are delivered in average hardness.

• Machine flood bar supports and doctor blades

20 mm

85 m

m

55 m

m

70 m

m

A type, for Electra metal profile flood bar, equipped with

50 x 9 mm interchangeable polyurethaneflood bar support with

interchangeable blued steel blade

MO type,metal profile flood bar, equipped with MO type 35 x 7 mm interchangeable polyurethaneflood bar support with interchangeable blued steel blade

hLS type,Metal profile flood bar, equipped with50 x 9 mm interchangeable polyurethaneflood bars support with interchangeable blued steel blade

SQUEEGEES & FLOOD BARS

B type, flood bar support with interchangeable blued steel blade

(1) specify the shape

Rh hLS MO Ev Electra Electrapneumatic

Electramechanics

flood bars HLS type MO type A type A type A type

flood bar supports HLS type MO type BP type B(1) type A type

• «one hand» flood bar

C type,wooden mounting, equipped with polyurethane 50 x 9 mm

110

mm

95 m

m

40 mm

20 mm

90 m

m

30 mm

135

mm

• Squeegee blades for manual printing

E type,small wooden moulding, equipped with polyurethane 25 x 5 mm

d type,large wooden moulding, equipped with polyurethane 50 x 9 mm

• General remarks- a squeegee blade with rounded angle deposits more ink than one sharpened at a right angle - a soft squeegee blade deposits more ink than a hard one - to print a fine or half tone pattern a very hard and perfectly sharpened squeegee blade must be used- the greater the angle of inclination of the squeegee blade, the more ink is deposited - absence of squeegee blade inclination can be compensated by sharpening the blade at an angle (possible with our inclined plane sharpener)- the print quality is directly related to the quality of the squeegee blade: a worn doctor blade is a bad tool.

• Special squeegee blades On request squeegee blade for drum machines, cylma and bottle machines.


Polyurethanes We propose a complete range of polyurethanes.• Qualities - monobloc (single-component) - composite (2 qualities one stuck above the other) - 3C (triple layers)• Shore hardness variable from 65 to 85° identified by the colour : red 65-70°, green 70-75°, blue 75-80°, gold 75-80° and 80-85°. The Gold variety is characterised by exceptional mechanical resistance to friction and UV. It is an excellent polyurethane.• Solid profile and double bevel 45°

IMP.

TIFL

EX 2

5.02

.201

3 - N

on c

ontra

ctua

l pic

ture

s

(3C)


SQUEEGEES & FLOOD BARS

Other dimensions : contact us.* Minimum Order: 3 lengths. Within 4 weeks.

dESCRiPtiOn Ref.MOnOBLOCS 20 x 5 mm

Red, solid, 3 m strip 244200510C3Green, solid, 3 m strip 244200510D3Gold 75° shore, solid, 3 m strip 244200510K3Gold 80° shore, solid, 3 m strip 244200511K3

MOnOBLOCS 25 x 5 mmRed, solid, 3 m strip 244250510C3Green, solid, 3 m strip 244250510D3Blue, solid, 3 m strip 244250510E3Gold 75° shore, solid, 3 m strip 244250510K3Gold 80° shore, solid, 3 m strip 244250511K3Green, double bevel 45°, 3 m strip 244250535L3Blue, double bevel 45°, 3 m strip 244250535M3Gold, 80° shore, double bevel 45°, 3 m strip 244250535N3

MOnOBLOCS 35 x 7 mmRed, solid, 3 m strip 244350710C3Green, solid, 3 m strip 244350710D3Gold 75° shore, solid, 3 m strip 244350710K3

MOnOBLOCS 40 x 5 mmGreen, solid, 3 m strip 244400510D3Blue, solid, 3 m strip 244400510E3

MOnOBLOCS 40 x 8 mm for Schenk printing machines*Green, plain, 3,33 m strip, 75°shore 244400810Q3Red, Bullnose, 3,33 strip, 65 shore 244400810P3

MOnOBLOCS 50 x 6 mmRed, solid, 3 m strip 244500610C3Green, solid, 3 m strip 244500610D3Blue, solid, 3 m strip 244500610E3

MOnOBLOCS 50 x 7 mmRed, solid, 3 m strip 244500710C3Green, solid, 3 m strip 244500710D3Gold 80° shore, solid, 3 m strip 244500711K3

MOnOBLOCS 50 x 9 mmRed, solid, 3,66 m strip 244500910C4Green, solid, 3,66 m strip 244500910D4Blue, solid, 3,66 m strip 244500910E4Brown, solid, 3,66 m strip 244500910F4Gold 75° shore, solid, 3,66 m strip 244500950K4Gold 80° shore, solid, 3,66 m strip 244500911Z4

DESCRIPTION Ref.

COMPOSitES 50 x 9 mm

Red, solid, 3 m strip 244500950C3

Green, solid, 3 m strip 244500950D3

DESCRIPTION Ref.

POLYUREthAnES 3C, 50 x 9 mm

Red, 3,66 m strip 245704

Green, 3,66 m strip 245604

Polyurethanes composites

Polyurethanes 3C

SCREEN PRINTING

*


ExPOSURE FILmS- masking films- mounting films




P.TI

FLEX

11.

02.2

013

in order to manufacture silk screens, tiflex offers masking films and mounting.

• Masking films They enable to obtain positive or negative expositions or colour selection. It can be cut manually or on a plotter controlled by computer. They are composed of a transparent and stable polyester base of 75 or 125 µ on which an inactinic translucent layer is laminated. Proposed in red : the layer is restickable. All these films are supplied in the following packagings :

thickness

packagingfilmac 75 µ filmac 125 µ

rolls :

10 x 1,03 m • •50 x 1,03 m • •

10 x 1,23 m • •50 x 1,23 m • •

thickness

packaging100 µ

rolls :

20 x 1,04 m •

• Mounting films

EXPOSURE FILMS

SCREEN PRINTING

*


CAPILLARY FILmS- pre-sensitised diazo photofilm




P.TI

FLEX

11.

02.2

013

- Non

con

tract

ual p

ictu

res

diazofilm is a pre-sensitised diazo photofilm for use with solvent-based and Uv inks. it combines all the advantages of an indirect film (regular layer and high definition) with those of a direct emulsion.

Diazofilm is made of a 20 or 30-micron thick emulsion, laid on a 75-micron polyester carrier. Its use is simple, quick and clean. The film is mounted by capillarity after wetting both sides of the screen. To obtain a good quality mounting of the Diazofilm, it is necessary to pre-treat the material with Prep’écran (see page : Products for screen manufacturing). This film offers excellent definition, great solidity and a perfect dimensional stability. The reclamation of screens exposed with Diazofilm is easy with Oxygel, Oxysol or Oxylic screen reclaimer followed by a final high pressure wash out. Diazofilm (20 or 30-micron) is packaged in 10 x 1,04 m rolls.

• thick capillary film Used for printing graphical effects on material, this film will set large volumes of ink into a regular layer. It is available in 2 thicknesses: 200 and 400 microns, or in boxes of 10 in the following sizes: 43 x 61 cm.

CAPILLARY FILMS

SCREEN PRINTING


*

TExTILE INkSFLASHCOLORQuick flash cure plastisol inks for textile printing. Direct printing and printing by transfer.


¾¾ Surface aspect: satin¾¾ Smell: very few¾¾ Average density: 1,25¾¾ Rheology: thixotropic ink¾¾ Fusion temperature infrared tunnel: 2 min. at 150 - 160°C

recommended: values to be adjusted depending on the material used (test the printing according to the washing programme recommended for the cloth)¾¾ Opacity: excellent¾¾ Coverage: 20 m²/l with a 48 -70 mesh¾¾ Washing resistance: good¾¾ Ironing: on the back¾¾ Plastifying thinner:

• drying activator 7158 (complies to OEKOTEX standard) • retarder XD 835 (does not comply to OEKOTEX)¾¾ Cleaning solvents: 2881, 2899, NS-81, NS-91 and NS-99¾¾ Expiry: refer to the label¾¾ Colours miscible together: yes

Quick flash cure plastisol inks for textile printing. Direct printing and printing by transfer.

Flashcolor

SPECIFICATIONS USEThe FLASHCOLOR inks are used with coated screens with Diazo S (19 S, 149 S) or Diazo - Photopolymer (UST, 200S) or Graphic HU, Textil HT, Textil PV solutions...

The fabric mesh is chosen according to the work to be carried out.

FLASHCOLOR inks can be used in two ways:

- Direct printing:For multiple printing, we recommend flashing between each colour.

After suitable heating treatment, the printed substrates at ambient temperature are touch dry and flexible.

Flashing time and polymerization time depend on the following factors : • ink type, colour and printed thickness • printed substrate, nature and colour • equipment used and its environment.

When a minimum flashing time is required, we recommend you to use our flash cure white.

Drying depends on the thickness of the ink film (the complete thickness of the ink film must reach the correct temperature), the material, the drying time, the colour of the ink and the support (extreme case of white on black fabric) and the fabric composition.

Remarks: When printing with FLASHCOLOR ink on textiles which are fragile at temperature of 150-160°C, catalyst XD 150 (representing 5% of the ink weight) can be added to the ink. The polymerization temperature may therefore be lowered by 10 - 20°C. In this case, the pot life will be about 8 hours.

Catalyst XD 150 will be used either to ensure a complete drying of a thick layer, either in case of a temperature sensitive thread or to reinforce the polymerization of gold and silver colours.

Blend the ink before use. Use only referenced additives

- Printing by transfer (refer to data sheet «TEXTILE TRANSFER»)

STORAGE AND TOXICOLOGYThe FLASHCOLOR inks comply with EN 71-3 standard.

Only our Web-site is authorised to give real-time information about our inks. Paper notices are considered unwritten and no longer engage our company’s responsibility once they are updated on our Web-site. Our responsibility can be engaged only if the customer has based his position on the information published on our Web-site. In all cases, the user should carry out validation tests under his own conditions before using our inks for his production. The safety data sheets are available free at: www.tiflex.com/fds

WHITE*3962012 1 l3964012 5 l

FLASH CURE WHITE3962010 1 l3964010 5 l

oPaQUE

Ref. Packaging

OPAQUE

3964078 5 l

HIGH OPACITY WHITE3964077 5 l

OPACITY YELLOW

3964002 5 l

OPACITY RED

3964008 5 l

sTaNDarD coloUrs

LEMON YELLOW*

3962015 1 l

3964015 5 l

MEDIUM YELLOW

3962016 1 l

3964016 5 l

GOLD YELLOW*

3962018 1 l

3964018 5 l

ORANGE*

3962019 1 l

3964019 5 l

SOLID RED*

3962009 1 l

3964009 5 l

RUBIS RED*

3962028 1 l

3964028 5 l

Ref. Packaging Ref. Packaging Ref. Packaging Ref. Packaging

FUCHSIA*

3962032 1 l

3964032 5 l

VIOLET*

3962039 1 l

3964039 5 l

ROYAL BLUE

3962041 1 l

3964041 5 l

ULTRAMARINE BLUE3962044 1 l

3964044 5 l

MID BLUE

3962046 1 l

3964046 5 l

PRIMARY BLUE*

3962048 1 l

3964048 5 l

REFLEX BLUE

3962025 1 l

3964025 5 l

DEEP BLUE

3962050 1 l

3964050 5 l

STEEL BLUE

3962054 1 l

3964054 5 l

BRIGHT GREEN

3962060 1 l

3964060 5 l

MEDIUM GREEN

3962062 1 l

3964062 5 l

GREEN

3962064 1 l

3964064 5 l

MINT GREEN*

3962066 1 l

3964066 5 l

EMERALD GREEN

3962068 1 l

3964068 5 l

CARAMEL

3962073 1 l

3964073 5 l

BLACK*

3962034 1 l

3964034 5 l

Non contractual colours and picturesOn simple request, we can propose you a color panel card displaying accurate shades.

CATALYST XD 1503981299 250 gr

CATALYST XD 1503982099 le kg

GELIFYING AGENT3952061 le kg

THINNER BASE*3962005 1 l3964005 5 l

THINNER BASE SOFT3962006 1 l3964006 5 l

PEARL BASE3962007 1 l3964007 5 l

PUFF AGENT PLASTISOL3952090 1 l3954090 5 l

GLITTER BASE3954096 5 l

SPARKLE GLUE3954099 5 l

PUFF TRANSFER BASE3954095 5 l

aDDITIoNal ProDUcTsRef. Packaging

Non

con

tract

ual c

olou

rs a

nd p

ictu

res

- IM

P. T

IFLE

X 28

.01.

2013

METallIc aND sPEcIal EFFEcT

SILVER3962090 1 l3964090 5 l

SPARKLE SILVER3962091 1 l3964091 5 l

GOLD3962095 1 l3964095 5 l

SPARKLE GOLD3962094 1 l3964094 5 l

SHINY GOLD3962093 1 l3964093 5 l

LUMINESCENT3962096 1 l3964096 5 l

REFLECTIVE3962098 1 l3964098 5 l

Ref. Packaging

coMPlEMENTarY ProDUcTsRef. Packaging

FlUo

FLUO YELLOW3962085 1 l3964085 5 l

FLUO ORANGE3962086 1 l3964086 5 l

FLUO RED3962087 1 l3964087 5 l

FLUO PINK3962088 1 l3964088 5 l

FLUO GREEN3962089 1 l3964089 5 l

Ref. Packaging

THIXO 4-COLOURS PROCESS

4-CoLoURS yELLow ThIXo3962080 1 l3964080 5 l

4-CoLoURS mAgENTA ThIXo3962081 1 l3964081 5 l

4-CoLoURS CyAN ThIXo3962082 1 l3964082 5 l

4-CoLoURS BLACk ThIXo3962083 1 l3964083 5 l

Ref. Packaging

TIFLEX would like to draw you attention to the following points:Before starting production, you are recommended to check the ink compatibility and resistance on a textile by washing the finished article according to the conditions indicated on its label. Washing resistance may be reduced with some dyes rich in bases or white (transparent or pastel colours).The washing resistance may also be reduced due to fibrillation (fibres projecting through the printing). This phe-nomenon is independent of the ink polymerisation. XD 150 catalyst will be used either to ensure complete poly-merisation of a thick layer or when using a fabric with poor temperature resistance. High washing temperatures

associated with powerful detergents may lead to colour changes with some colours including gold and silver.




SCREEN PRINTING


*

TEXTILE INkSOEkOfLaShQuick flash plastisol ink which can be used with textiles which will be classified: ŒkOTEX 100 Class I.Direct printing and printing by transfer. WIThOUT PhThaLaTE.

PhThaLaTE fREE

PhThaLaTE fREE

¾¾ Appearance: satin¾¾ Smell: very few¾¾ Average density: 1,25¾¾ Rheology: thixotropic ink¾¾ Polymerisation: 2min.at150-160°Cvaluestobeadjusteddepending

onthematerialused(testtheprintingaccordingtothe washingprogrammerecommendedforthearticle)¾¾ Coveringpowerbyopacity: excellent¾¾ Coveragerate: 20m²/lwitha48-70mesh¾¾ Washing resistance: good¾¾ Ironing: on the reverse side¾¾ Diluentaccelerator: 7158¾¾ Cleaningsolvents: 2881,2899,NS-81,NS-91andNS-99¾¾ Expiry: refertothelabel¾¾ coloursmiscibletogether: yes

Quick flash plastisol ink which can be used with textiles which will be classified: ŒKOTEX 100 Class I.Direct printing and printing by transfer. WITHOUT PHTHALATE.

OekOflash

SPECIFICATIONS USEThe ŒKOFLASHinksareusedwithscreenscoatedwithDiazoS(19S,149S)orDiazo-Photopolymer(UST,200S)orGraphicHU,TextilHT,TextilPV...solutions.

Themeshischosenaccordingtotheworktobecarriedout.

Formultipleprinting,werecommendflashingbetweeneachcolour.

Aftersuitableheatingtreatment,theprintedSUBSTRATESatambienttemperaturearetouchdryandflexible.

Timeforflashingandpolymerisationarefunctionofthefollowingfactors:

-inktype,colourandprintedthickness-printedsubstrate,natureandcolour-usedequipmentandenvironment.

Whenaminimumflashingtimeisrequired,werecommendtheuseoflightningwhite.

Dryingdependsonthethicknessoftheinkfilm(thecompletethicknessoftheinkfilmmustreachthecorrecttemperature),thematerial,thedryingtime,thecolouroftheinkandthesupport(extremecaseofwhiteonblackfabric)andthefabriccomposition.

N.B.: When printing with ŒKOFLASH ink on textiles which are fragile at temperature of 150-160°C, 5 % by weight of catalyst XD 150can be added to the ink. The polymerisation temperaturemay therefore be lowered by 10 - 20°C. In this case, the pot lifewill be about 8hours.ItdoesnotavoidapassageI.R.dryingtunnel.


-Printingbytransfer(refertodatasheet«TEXTILETRANSFER»)

STOrAgE AND TOXICOLOgyThe ŒKOFLASH inkscomplywithEN71-3standardandinclothingwhichwillreceiveŒKOTEX100classI labelling forbabies.

S C R E E N P R I N T I N GOnly our Web-site is authorised to give real-time information about our inks. Paper notices are considered unwritten and no longer engage our company’s responsibility once they are updated on our Web-site. Our responsibility can be engaged only if the customer has based his position on the information published on our Web-site. In all cases, the user should carry out validation tests under his own conditions before using our inks for his production. The safety data sheets are available free at: www.tiflex.com/fds

sTaNDaRD COlOURs

LEmON yELLOW*

3934013 5 l

mEDIUm yELLOW

3934003 5 l

gOLD yELLOW*

3934004 5 l

OrANgE*

3934012 5 l

SOLID rED*

3934010 5 l

rUBIS rED*

3934011 5 l

Ref.Packaging Ref.Packaging Ref.Packaging Ref.Packaging

FUCHSIA*

3934015 5 l

vIOLET*

3934016 5 l

rOyAL BLUE

3934024 5 l

mID BLUE

3934021 5 l

PrImAry BLUE*

3934020 5 l

rEFLEX BLUE

3934025 5 l

DEEP BLUE

3934026 5 l

mEDIUm grEEN

3934034 5 l

grEEN

3934031 5 l

mINT grEEN*

3934035 5 l

EmErALD grEEN3934033 5 l

BLACK*

3934044 5 l

WHITE*3934000 5 l

KILImANDjArO WHITE

3954010 5 l

FLASH CUrE WHITE3934086 5 l

HIgH OPACITy WHITE3934082 5 l



Non

con

tract

ual c

olou

rs a

nd p

ictu

res

- IM

P. T

IFLE

X 28

.10.

2012


4-COLOURS PROCESS THIXO

4-COLOUrS yELLOW THIXO3934051 5 l

4-COLOUrS mAgENTA THIXO3934052 5 l

4-COLOUrS CyAN THIXO3934054 5 l

4-COLOUrS BLACK THIXO3934056 5 l

Ref.Packaging

SPECIAL EFFECT

SPArKLE SILvEr3934091 5 l

SPArKLE gOLD3934094 5 l

Ref.Packaging

Bases

THINNEr BASE*3934066 5 l

SOFT BASE3934067 5 l

gLOSSy ELASTIC BASE3954091 5 l

Ref.Packaging

COMPLEMENTARY PRODUCTS

CATALyST XD 1503981299 250gr

gELIFyINg AgENT3982099 le kg

Ref.Packaging

TIFLEX would like to draw you attention to the following points:Beforestartingproduction,youarerecommendedtochecktheinkcompatibilityandresistanceonatextilebywashingthefinishedarticleaccordingtotheconditionsindicatedonitslabel.Washingresistancemaybereducedwithsomedyesrichinbasesorwhite(transparentorpastelcolours).Thewashingresistancemayalsobereducedduetofibrillation(fibresprojectingthroughtheprinting).Thisphe-nomenonisindependentoftheinkpolymerisation.Highwashingtemperaturesassociatedwithpowerfuldetergentsmayleadtocolourchangeswithsomecoloursincludinggoldandsilver.

BP3-01450PONCIN-FranceInternationalSales:Tel.+33(0)474373380/97-Fax+33(0)[email protected]

TExTILE INkS

SCREEN PRINTING


*

PHTHALATE FREE

EVERESTPhthalate free Plastisol ink, It can be flash cured and printable on oekotex 100 Class 1 certified fabrics. For direct and transfer printing. wIThoUT PhThALATE.


¾¾ Appearance: satin

¾¾ Smell: very few

¾¾ Average density: 1,25

¾¾ Rheology: thixotropic ink

¾¾ Polymerisation: 2 min. at 150 - 160°C values to be adjusted depending on the material used (test the printing based on the planned wash program for the article)

¾¾ Covering power by opacity: excellent

¾¾ Coverage rate: 20 m²/l with a 48 -70 mesh

¾¾ Washing resistance: good

¾¾ Ironing: on the reverse side

¾¾ Diluent accelerator: 7158

¾¾ Plastifying diluent Everest: 3194024

¾¾ Cleaning solvents: 2881, 2899, NS-81, NS-91 and NS-99

¾¾ Expiry: refer to the label

¾¾ Colours miscible together: yes

Phthalate free Plastisol ink, It can be flash cured and printable on Oekotex 100 Class 1 certified fabrics. For direct and transfer printing. WITHOUT PHTHALATE.

EvErEsT

SPECIFICATIONS USEThe EVEREST inks are used with screens coated with Diazo S (19S/149S) or Diazo-Photopolymer (UST, 200S) or Graphic HU, Textil HT, Textil PV solutions. Fabric mesh is chosen based on the work to be carried out.For multiple printing, we recommend you to flash between each colour.After suitable heating treatment, the printed substrates, at ambient temperature, are touch dry and flexible.Times for flashing and polymerization are based on: • The ink, its colour, and the thickness deposited • The printed substrate, its make-up , its colour • The material used and its environmentNote: we also recommend you to add our hardener XD 150 (representing 5% of the ink weigh) in case of printing of fragile fabrics (polyme-rization at 150°C/160°C).Then the temperature of polymerization could be lowed from 10°C to 20°C.In that case, “pot life” will be around 8 hours.The hardener will be used either to ensure complete polymerization of a wide layer, either in case of a specific washing resistance (fragile fabric) or for a short drying in an IR oven.

Transfer printing will be done with the Everest ink like the other plastisol inks in general and you can use a special Everest adhesive.Blend the ink before use. Use only referenced additives

STORAGE AND TOXICOLOGYThe Everest inks comply with the norm EN 71-3 and can be printed on Oekotex 100 Class 1 babies clothes.

PHTHALATE FREE

Ref. Packaging

WHITE*39C4000 5 l

ANTI BLEEDING WHITE39C4095 5 l

POLAR WHITE

39C4095 5 l

FLASH CURE WHITE

39C4086 5 l

sTaNDarD coloUrs

LEMON YELLOW*

39C4002 5 l

MEDIUM YELLOW

39C4003 5 l

GOLD YELLOW*

39C4004 5 l

ORANGE

39C4006 5 l

SOLID RED*

39C4013 5 l

RUBIS RED*

39C4011 5 l

Ref. Packaging Ref. Packaging Ref. Packaging

FUSCHIA*

39C4015 5 l

VIOLET*

39C4016 5 l

ROYAL BLUE

39C4024 5 l

MID BLUE

39C4021 5 l

PRIMARY BLUE*

39C4020 5 l

REFLEX BLUE

39C4025 5 l

DEEP BLUE

39C4026 5 l

GREEN

39C4031 5 l

MINT GREEN*

39C4035 5 l

EMERALD GREEN

39C4033 5 l

BLACK*

39C4044 5 l


IMP.

TIF

LEX

13.0

6.20

13. N

on c

ontra

ctua

l col

ours

and

pic

ture

s.

4-COLOURS PROCESS

4-CoLoURS yELLow39C4050 5 l

4-CoLoURS mAgENTA39C4052 5 l

4-CoLoURS CyAN39C4054 5 l

4-CoLoURS BLACk39C4056 5 l

Ref. Packaging

BasEs

THINNER BASE*39C4066 5 l

ELASTIC BASE39C4092 5 l

Ref. Packaging

sPEcIal EFFEcT

SPARKLE SILVER39C4091 5 l

SPARKLE GOLD39C4094 5 l

Ref. Packaging

aDhEsIvEs

aDhEsIvEs

WHITE ADHESIVE39C4098 5 l

TRANSPARENT ADHESIVE39C4099 5 l

POWDER ADHESIVE3863327 3 kg

PLASTIFYING3194024 5 l

Ref. Packaging

Ref. Packaging

TIFLEX would like to draw you attention to the following points:Before starting production, you are recommended to check the ink compatibility and resistance on a textile by washing the finished article according to the conditions indicated on its label.Washing resistance may be reduced with some dyes rich in bases or white (transparent or pastel Colours).The washing resistance may also be reduced due to fibrillation (fibres projecting through the printing). This phe-nomenon is independent of the ink polymerisation.High washing temperatures associated with powerful detergents may lead to colour changes with some Colours including gold and silver.



SCREEN PRINTING


*

DREAmFLASHPVC and PHTHALATE FREE ink printable on Oekotex 100 Class 1 certified fabrics. Direct printing and transfert printing.

TExTILE INkS

PVC FREEPHTHALATE FREE


PVC FREEPHTHALATE FREE

sTaNDarD coloUrs

LEMON YELLOW*

39A4002 5 l

GOLD YELLOW*

39A4004 5 l

ORANGE*

39A4006 5 l

SOLID RED*

39A4013 5 l

RUBIS RED*

39A4011 5 l

FUSCHIA*

39A4015 5 l

Ref. Packaging Ref. Packaging

VIOLET*

39A4016 5 l

PRIMARY BLUE*

39A4020 5 l

MINT GREEN*

39A4035 5 l

BLACK*

39A4044 5 l

WHITE*39A4000 5 l

THINNER BASE*39A4058 5 l

ADHESIVE

3864033 5 l

POWDER ADHESIVE

3863327 3 kg

4-COLOURS PROCESS

4-CoLoURS yELLow39A4050 5 l

4-CoLoURS mAgENTA39A4052 5 l

4-CoLoURS CyAN39A4054 5 l

4-CoLoURS BLACk39A4056 5 l

Ref. Packaging

¾¾ Appearance: satin¾¾ Smell: very few¾¾ Average density: 1,20¾¾ Rheology: thixotropic ink¾¾ Polymerisation: 2 min. at 140°C

values to be adjusted depending on the material used (test the printing according to the washing programme recommended for the article)¾¾ Covering power by opacity: excellent¾¾ Coverage rate: 20 m²/l with a 48 -70 mesh¾¾ Washing resistance: good¾¾ Ironing: on the back¾¾ Diluent accelerator: 7158¾¾ Cleaning solvents: 2881, 2891, 2899 and NS-91¾¾ Expiry: refer to the label¾¾ colours miscible together: yes

PVC and PHTHALATE FREE ink printable on Oekotex 100 Class 1 certified fabrics. Direct printing and transfert printing.

DrEaMFlash

SPECIFICATIONS USEDREAMFLASH inks are using with Diazo S or Diazo (19 S, 149 S) - Photopolymer (UST, 200S) or Graphic HU, Textil HT, Textil PV solutions... coated screens. Stitch material is function of the work to realize.In case of multiple printings, we recommend you to flash between each colour.After adaptable thermic treatment, ambient temperature printings are dry and supple.Flashing and polymerization times are function of : • ink, its colour and its thickness • printed substrate, its composition, its colour • susbtrate used and its environmentWe advice you to determinate flashing and polymerization times by successive tests.Transfer printing:We advise you to use a powder adhesiveSupport: printing on matt polyester film 2543600 or on siliconed paper 2543300Pregelling in the tunnel: 2 min at 120°CTextile transfer by heating press: pressure 4 bars, t°c 140°C - 160°C, time ; 20 secWe advise you to check the following parameters thanks to several washing resistance tests. In order to reinforce physical properties of the ink you can add 5% of hardener XD150.Therefore pot-life will be reduced to 2 hours maximum.


STORAGE AND TOXICOLOGYThe DREAMFLASH inks comply with the norm EN 71-3 and can be printed on Oekotex 100 Class 1 babies clothes.

TIFLEX would like to draw your attention to the following points:Before starting production, you are recommended to check the ink compatibility and resistance on a textile by washing the finished article according to the conditions indicated on its label.Washing resistance may be reduced with some dyes rich in bases or white (transparent or pastel colours).The washing resistance may also be reduced due to fibrillation (fibres projecting through the printing). This phenomenon is independent of ink polymerisation.High washing temperatures associated with powerful detergents may lead to colour changes with some colours.

MP.

TIF

LEX

13.0

6.20

13


sPEcIal EFFEcT

oPaQUE

SPARKLE SILVER39A4091 5 l

SPARKLE GOLD39A4094 5 l

HIGH OPAQUE WHITE39A4080 5 l

Ref. Packaging

Ref. Packaging


SCREEN PRINTING


*

TExTILE INkSAQUADIRwater-based polyurethane ink for printing directly on textiles. It yields flexible and elastic prints.Used with a hardener, it can dry below 100 °C and limit the drawing of the printed fabrics.


MP.

TIF

LEX

28.0

1.20

13

aQUaDIrWater-based polyurethane ink for printing directly on textiles. It yields flexible and elastic prints.Used with a hardener, it can dry below 100 °C and limit the drawing of the printed fabrics.

¾¾ Finish: satin¾¾ Odour: very slight¾¾ Average density: 1.25¾¾ Rheology: thixotropic ink¾¾ Polymerisation: - 2 min at 160 °C in IR tunnel, value to be

adjusted according to the material used (test the printing according to the wash programme recommended); to avoid drawing of the dyes or the fabric, it is possible to add low temperature hardeners that work under the following conditions: - with hardener 3540560 at 2%, 2 min at 90 °C in IR tunnel, value to be adjusted according to the material used (test the printing according to the wash programme recommended) - for drying at room temperature, hardener 3540561 must be mixed at up to 2 % (wait 8 to 15 days before washing to test the printing)¾¾ Cleaning solvents: water¾¾ Covering power: good¾¾ Surface yield: 20 m²/l with 36 - 70 fabric¾¾ Washing resistance: correctly fixed, resists domestic

washing: 30 to 50 °C cycles¾¾ Ironing: on the reverse¾¾ Retarding diluent: 3X9394¾¾ Shelf life: 12 months¾¾ Storage conditions: between 0 °C and 35 °C¾¾ Colours miscible together: yes

The AQUADIR inks comply with EN 71-3 standard.

sPEcIFIcaTIoNs UsE

sToragE aND ToxIcologY

The AQUADIR inks are used with coated screens with 19T, 200T, UST or Textil HT solutions. The fabric mesh is chosen according to the work to be carried out. To achieve maximum opacity, we recommend you to use size of mesh from 36 and 70 fibres/cm.For multiple printing, we recommend you to flash between each colour.The last layer has to be dried in an IR tunnel during 2 minutes at 160°C. In case of ink blending combined with low temperature hardener to avoid pigments migration, drying conditions will consequently be 100°C for 2 mn.

IMPlEMENTaTIoNPreparation is required before using this range of inks.The pigmented concentrates are used with the thinner base on its own or with the thinner base and the blending white.

PrEParaTIoN• Red resist, ruby red and black, 90% thinner base, 10% pigmented concentrate.• Lemon, thinner base 37,5%, blending white 60%, 2,5% pigmented concentrate.• Other colours, 20% base, 60% white, 20% pigment concentrate.• Gold paste 20 %, base 80 %.• Silver paste 13 %, base 87 %.

TIFLEX would like to draw your attention to the following points:Before starting production, you are recommended to check ink compatibility and resistance on a textile by washing the finished article according to the conditions indicated on its label.Washing resistance may be reduced with some dyes rich in base colours or white (transparent or pastel colours) or a too important incorporation of pigment concentrates. The washing resistance may also be reduced due to fibrillation (fibres projecting through the printing). This phenomenon is independent of ink polymerisation.High washing temperatures associated with powerful detergents may lead to colour changes with some colours.

PIgMENT coNcENTraTEs

LEMON

3522002 1 l

YELLOW

3522004 1 l

ORANGE

3522006 1 l

CHERRY RED

3522008 1 l

RUBIS RED

3522012 1 l

FUSCHIA

3522015 1 l


VIOLET

3522016 1 l

PRIMARY BLUE

3522020 1 l

MINT GREEN

3522035 1 l

BLACK

3522044 1 l

Ref. Packaging

THINNER WHITE

3544000 5 l

COVERING WHITE

3544087 5 l

sTaNDarD coloUrs

Ref. Packaging

Ref. Packaging

Ref. Packaging

THINNER BASE

3544066 5 l

BasE

METallIc

SYLVER PASTE3542046 1 kg

GOLD PASTE3562096 1 kg

aDDITIvEs

ROOM TEMPERATURE HARDENER3540561 100 g

LOW TEMPERATURE HARDENER3540560 100 g



SCREEN PRINTING


*

TExTILE INkSAQUATRANSwater-based polyurethane ink (mono component) for transfer printing. Good flexibility, high elasticity.


ADHESIVES3864041 5 l

Thermofusing powder adhesivePolyester 3863327 3 kg

Thermofusing powder adhesive PU3863328 3 kg

¾¾ Appearance: satin¾¾ Smell: very little¾¾ Average density: 1.25¾¾ Rheology: thixotropic ink¾¾ Cleaning product: water¾¾ Covering power: good¾¾ Coverage rate: approx. 20 m²/l with a 49- 70 mesh¾¾ Washing resistance: correctly fixed, it resists

domestic washing: cycles to be launched from 30°C to 50 °C cycles¾¾ Elasticity: excellent¾¾ Ironing: on the reverse¾¾ Delaying agent: 3X9394¾¾ Thickner: 3Y1598¾¾ Expiry date: 12 months¾¾ Storage conditions: between 0° and 35°C¾¾ Colours miscible together: yes

aQUaTraNsWater-based polyurethane ink (mono component) for transfer printing. Good flexibility, high elasticity.

1) Printing on polyester film for mat transfer 2543600 or siliconed paper 2543300 (*by 250 sheets, size 70 x 50 cm) and 2543600 (by 250 sheets, size 70 x 100 cm).2) Pre-drying of the dyes: 2 mn at 80°C at pulsed air tunnel3) Printing of the adhesive (mesh 36 threads/cm). Drying : 2 mn at 50 - 60°C. or use a powder adhesive: - PU 3863328, drying 2 mn at 90°C - PET 3863327, drying 2 mn at 105°C4) Transfer on textile with a heating press by respecting the following recommendations: - Powder PU pressure 3 to 5 bars temperature 140 - 150°C time 15 to 30 secondsIn that case, we advise you not to wash and dry over 60°C. - Poudre PET pressure 3 to 5 bars temperature 150 - 180°C time 20 to 30 seconds5) Take out the transfer substrate only after complete cooling.

The AQUATRANS inks comply with EN 71-3 standard.

sPEcIFIcaTIoNs


UsE

UsE

TIFLEX would like to draw your attention to the following points:Before starting production, you are recommended to check the ink compatibility and resistance on a textile by washing the finished article according to the conditions indicated on its label.Washing resistance may be reduced with some dyes rich in base colours or white (transparent or pastel colours).The washing resistance may also be reduced due to fibrillation (fibres projecting through the printing). This phenomenon is inde-pendent of ink polymerisation.High washing temperatures associated with powerful detergents may lead to colour changes with some colours.

Ref. Packaging

THINNER WHITE

3524000 5 l

COVERING WHITE

3524087 5 l

BasE

Ref. Packaging

THINNER BASE

3524066 5 l

BASE FOR METALLIC PASTE

3524095 5 l

BasE

Ref. Packaging

aDhEsIvEs


LEMON

3522002 1 l

YELLOW

3522004 1 l

ORANGE

3522006 1 l

CHERRY RED

3522008 1 l

RUBIS RED

3522012 1 l

FUSCHIA

3522015 1 l


VIOLET

3522016 1 l

PRIMARY BLUE

3522020 1 l

MINT GREEN

3522035 1 l

BLACK

3522044 1 l

Please respect the following points:Before you start printing pass the transfer paper through the dryer to condition the transfer paper prior to printing.Polymerization of the ink on the transfer support could lead to problems with adhesion to the fabric.Preliminary tests must be carried out to check the resistance of the textile to the press and ensure paper to textile transfer.Adding a big quantity of pigment concentrates (30%) can damage the transfer, particularly if used exposure.Particular case: in case of drying over 60°C- special base 3Y2804- Powder PU 3Y2911- Covering white 3524087 to prepare various shades

IMPlEMENTaTIoNPreparation is required before using this range of inks.The pigment concentrates are used with the thinner base on its own or with the thinner base and the blending white.

PrEParaTIoN • Red resist, ruby red and black, 90% base 10% pigmented concentrate. • Lemon, thinner base 37,5%, blending white 60%, 2,5% pigmented concentrate. • Other colours, 20% base, 60% white, 20% pigment concentrates.

MP.

TIF

LEX

28.0

1.20

13



SCREEN PRINTING


*

TExTILE INkSHYDROCOLOR NGAcrylic water based ink, formaldehyde FREE for direct printing only on polyester, cotton or blends.

¾¾ Appearance: satin¾¾ Smell: very few¾¾ Fixing: - 2 to 3 min. at 160°C in IR tunnel

- by cold catalysis with an addition before printing of 5% of catalyst 35A0564; in this case, the catalyzed ink can only be used for 48 h. Caution: covering white, fluo colours and metallised inks must absolutely be cured, since they are not printed with a catalyst¾¾ Solidity: correctly fixed, Hydrocolor NG ink resists to domestic washings

(cycles for printed fabrics from 30°C to 50°C)¾¾ Coverage rate: varies from 9 to 12 m²/l depending on the screen used

and the substrate printed¾¾ Cleaning the equipment: water¾¾ Expiry: refer to the label

Acrylic water based ink, formaldehyde FREE for direct printing only on polyester, cotton or blends.

hYDrocolor Ng

SPECIFICATIONS USEHydrocolor NG is printed with a mesh 48 threads/cm and emulsions such as DIAZO T, UST and 200TThe thixothropy of the ink can be increased according to the following procedure : add while stiring from 10 g to 25 g of thickener XH 690 in 5 liters of ink then progressively add 25 g of a 25% ammoniacal solution in water.Note that the colour Hydrocolor NG Gold is delivered in two packages: • base for metallic paste 3564095 (in 5 l can) • rich pale gold paste 3562096 (in 1 kg pot)The base and the paste must be mixed just before use in proportions of 85 / 15 by weight.The mixture obtained must be used the same day.

STORAGE AND TOXICOLOGYThe HYDROCOLOR NG inks contain no dangerous solvents (in compliance with the Decree dated 21/02/90).They comply with EN 71-3 standard.


sTaNDarD coloUrs

LEMON

35A2002 1 l

35A4002 5 l

GOLD YELLOW

35A2004 1 l

35A4004 5 l

ORANGE

35A2006 1 l

35A4006 5 l

SCARLET

35A2007 1 l

35A4007 5 l

RED

35A2008 1 l

35A4008 5 l

DARK RED

35A2009 1 l

35A4009 5 l


FUCHSIA

35A2015 1 l

35A4015 5 l

VIOLET

35A2016 1 l

35A4016 5 l

BRIGHT BLUE

35A2020 1 l

35A4020 5 l

ROYAL BLUE

35A2024 1 l

35A4024 5 l

DEEP BLUE

35A2026 1 l

35A4026 5 l

BRIGHT GREEN

35A2030 1 l

35A4030 5 l

DARK GREEN

35A2034 1 l

35A4034 5 l

OLIVE GREEN

35A2035 1 l

35A4035 5 l

BROWN*

35A2042 1 l

35A4042 5 l

BLACK

35A2044 1 l

35A4044 5 l

THINNER WHITE

35A2085 1 l35A4085 5 l

COVERING WHITE

35A2087 1 l35A4087 5 l


*Acrylic water based ink, formaldehyde FREE.

Non

con

tract

ual c

olou

rs a

nd p

ictu

res

- IM

P. T

IFLE

X 28

.10.

2012

TIFLEX would like to draw your attention to the following points:Washing resistance may be reduced with some dyes rich in bases or white (transparent or pastel colours).The washing resistance may also be reduced due to fibrillation (fibres projecting through the printing) with some fabrics. This phenomenon is independent of the ink polymerisation.Before starting production, you are recommended to check the ink compatibility and resistance on a textile by washing the finished article according to the conditions indicated on its label.

4-COLOURS PROCESS

4-CoLoURS yELLow35A2050 1 l35A4050 5 l

4-CoLoURS mAgENTA35A2052 1 l35A4052 5 l

4-CoLoURS CyAN35A2054 1 l35A4054 5 l

4-CoLoURS BLACk35A2056 1 l35A4056 5 l

Ref. Packaging

FlUo

FLUO LEMON35A2070 1 l35A4070 5 l

FLUO GOLD YELLOW*35A2075 1 l35A4075 5 l

FLUO ORANGE*35A2073 1 l35A4073 5 l

FLUO RED*35A2071 1 l35A4071 5 l

FLUO PINK*35A2074 1 l35A4074 5 l

FLUO GREEN*35A2072 1 l35A4072 5 l

Ref. Packaging BasEs

THINNER BASE35A4066 5 l

PRODUCTION BASE35A4058 5 l

BASE METALLIC PASTE35A4095 5 l

Ref. Packaging

sPEcIal EFFEcT

GOLD PASTE3562096 1 l

Ref. Packaging

aDDITIvEs

CATALYST35A0564 100 g

THICKENER35A0263 25 g

Ref. Packaging



*Acrylic water based ink, formaldehyde FREE.

SCREEN PRINTING


*

TExTILE INkDISCHARGE INkWater based ink composed of a base (coloured or not) and an additive.Discharge ink (base + additive) removes the back dye of a cotton fabric.


IMP.

TIF

LEX

28.

01.2

013

- Non

con

tract

ual p

ictu

res

LEMON

3522002 1 l

YELLOW

3522004 1 l

ORANGE

3522006 1 l

CHERRY RED

3522008 1 l

RUBIS RED

3522012 1 l

FUSCHIA

3522015 1 l

¾¾ Water based acrylic base¾¾ pH: 8-9¾¾ Ionic character: anionic/non ionic¾¾ Pot life: 8 hours after adding the additive

water based ink composed of a base (coloured or not) and an additive.Discharge ink (base + additive) removes the back dye of a cotton fabric. The addition of a pigment concentrate to this preparation allows to replace the initial dying by a new one.Acting as a decoloration/dying process, the printed areas has no touch and does not require a underlayer of white on dark fabrics.CAUTIoN: only some textile back dyes can be removed with discharge inks. So please check with the fabric manufacturer if the fabric could match with the discharge ink (we strongly advise you to perform some tests).

DIschargE INk

SPECIFICATIONS USE

COLOURS

Before use, the additive must be mixed with the base or with the coloured base and pigment or with white colour in the fol-lowing proportions:On clear substrates Base or white or coloured base: 850g Additive: 50gOn dark substrates Base or white or coloured base: 850g Additive: 100gThe additive must be perfectly mixed with the base or colours.After printing, the fabrics must not be stored for more than 2 hours at ambient temperature to ensure that the active product does not penetrate more into the fabric and does not bleach a larger area more than expected.Drying: 2mn at 160°C.Thinner:It will need to be diluted, if necessary, with maximum 5% of water.Cleaning the screens:WaterScreen:36 to 77 threads/cmEmulsion:200T (resistant to water based inks).

They can be obtained by mixing the base.

PREPARATION OF THE COLOURSMIX: 2% to 5% pigment concentrate to 98-95% base.

The colour preparation has to be done prior to the addition of additive.



VIOLET

3522016 1 l

PRIMARY BLUE

3522020 1 l

MINT GREEN

3522035 1 l

BLACK

3522044 1 l

WHITE

3754000 4.250 l

BASE

3754058 4.250 l

ADDITIVE

3751264 250 g

sTaNDarD coloUrs

Ref. Packaging


SCREEN PRINTING


*

TExTILE INkSPOLYTHANEIf offers a strong covering power and high flexibility required for folding and bending operations. Air drying ink intended for printing on fabrics and especially thick synthetics, used mainly to make bags, covers, cases, clothing, etc...

PolYThaNEIf offers a strong covering power and high flexibility required for folding and bending operations. Air drying ink intended for printing on fabrics and especially thick synthetics, used mainly to make bags, covers, elastomer TPU, cases, clothing, etc...By adding Plastisol adhesives, thermofusing Oekoflash or thermofusing adhesive powder, Polythane ink mixed with catalyst XF 822 can be applied by transfer on bags or working cloths.

¾¾ Appearance: satin¾¾ Average density: 1,30¾¾ Viscosity: 38 ± 5 Pa.s¾¾ Drying:

• ambient air 30 min. at 20°C • air jet dryer 2 min. at 60°C¾¾ Pot life of the ink + catalyst mixture: 12 hours¾¾ Opacity: excellent¾¾ Coverage rate: 25 m²/kg with a 48 mesh¾¾ Weather resistance: good¾¾ Light fastness: good¾¾ Solvents:

• thinner 4905 • retarder 4906¾¾ Cleaning solvents:

• manual 2891, NS-81, NS-91 and NS-99 • washer 2881, 2899, NS-81, NS-91 and NS-99¾¾ Storage and expiry: refer to the label

POLYTHANE ink can be used on most substrates made from synthetic fabric, using screens ranging from 21 to 90 threads/ cm.For ordinary use where no specific resistance is required it can be used without catalyst.When increased resistance is required (adherence, flexibility, weather resistance), add to the POLYTHANE ink 10 % by weight of hardener XF 822.When printing on textile which will be washed in domestic washing machines, it is essential to use catalyst XF 822.we recommend you to check the ink compatibility and resistance on a textile by washing the printed item according to the specifications written on its label.This ink combined with a catalyst allows you to print working cloths by direct printing or by transfer (contact us for more informations).Printing by transferYou must use a powder adhesive for printing transfer.Polythane ink, combined with 10% of hardener XF 822 (representing 10% of the ink weigh), will be fixed on a matt polyester film for transfer ref 2543600Pre-gelling: ambient air or in the tunnel (1 min at 110°C after letting an adhesive powder)Printing transfer: pressure 3 to 5 bars, temperature: 170°C - 190°C.We advise you to check the following parameters with several washing resistance tests.

The POLYTHANE inks comply with EN 71-3 standard.

sPEcIFIcaTIoNs


UTIlIsaTIoN


WHITE

3472085 1 kg

WHITE

3472012 1 kg

sTaNDarD coloUrs

LEMON OP

3472002 1 kg

GOLD YELLOW OP3472004 1 kg

ORANGE OP

3472006 1 kg

CHERRY RED OP

3472008 1 kg

CYCLAMEN

3472039 1 kg

VIOLET

3472042 1 kg


PRIMARY BLUE

3472048 1 kg

DEEP BLUE

3472050 1 kg

MEDIUM GREEN OP3472033 1 kg

DEEP GREEN OP

3472034 1 kg

BLACK

3472072 1 kg

ExTra oPaQUE

YELLOW

3472087 1 kg

RED

3472088 1 kg

GREEN

3472089 1 kg


Non

con

tract

ual c

olou

rs a

nd p

ictu

res

- IM

P. T

IFLE

X 28

.01.

2013

CATALYST XF 8223470503 100 g

GELIFYING AGENT3952061 1 kg

GELIFYING AGENT 100 ml3470590

GELIFYING AGENT 1 l3472090

aDDITIvEsRef. Packaging Ref. Packaging Ref. Packaging Ref. Packaging

sPEcIal EFFEcT

RETROREFLECTIVE3472075 1 kg

BasEs

4-CoLoURS BASE ThIXo3472058 1 kg

THINNER BASE3472084 1 kg


4-CoLoURS yELLow ThIXo3472051 1 kg

4-CoLoURS mAgENTA ThIXo3472052 1 kg

4-CoLoURS CyAN ThIXo3472054 1 kg

4-CoLoURS BLACk ThIXo3472056 1 kg



SCREEN PRINTING


*

TExTILE TRANSFER Printing of the reversed patern on the silicon paper.

THERMOFUSING PLASTISOL ADHESIVE

3864021 5 l

THERMOFUSING PLASTISOL ADHESIVE WHITE

3864022 5 l

THERMOFUSING OEKOFLASH ADHESIVE

3864031 5 l

WHITE ADHESIVE EVEREST39C4098 5 l

TRANSLUCID ADHESIVE EVEREST

39C4099 5 l

THERMOFUSING POWDER ADHESIVE POLYESTER 3863327 3 kg

POWDER FOR TRANSFERto add to the inks (max 10%)3863317 3 kg

No

cont

ract

ual p

ictu

res -

IMP.

TIF

LEX

28.0

1.20

13

TExTIlE TraNsFEr

1) Printing of the reversed patern on the silicon paper.2) Pregelling in the tunnel : 1 mn to 100-110°C function of the equipment. Prints are not polymerisded.3) Transfer on the textile by heating press with these following conditions : pressure 3 to 5 bars, temperature : 170-190°C, time 20 - 30 s.4) Take off the silicon paper after total cooling.N.B. : For a better adherence on the textil, use adhesive powder (ref. 3863327).Using advices: • Put the paper with blanks in IR tunnel before starting printing. • For a transfer application, ink polymerisation on the paper would bring defects for textil transfer. • Test textil resistance under the press and also for transfer from paper to textil.

Advantage polyester versus paper: transparency and thermic stability.

Advantage of polyester film over siliconed paper: shiny polyester film can be used as a surfacing film in order that your direct printings or transfer printings get a glazed finish.Concerning the transfer of AQUATRANS, DREAMFLASH and POLYTHANE inks, please refer to the related pages descri-bing each of them.

UsE aDDITIoNal ProDUcTs

Ref. Packaging Ref. hoT-mELT FILm (mylar)in 0,75 x 125 m roll gold 25B2100 silver 25B2200

SILICONE PAPER, 105 gr/m²per 250 sheets 70 x 50 cm 2543300

70 x 100 cm 2543400

POLYESTER FILM FOR TRANSFER,size 70 x 50 cm per 200 sheets mat 2543600 high 2543500



The references ADHESIVE OEKOFLASH THERMOFUSING, ADHESIF POWDER THERMOFUSING and POWDER TRANSFER comply to OEKOTEX Standard Class 100 -1 for baby articles.

SCREEN PRINTING


*

USE OF wHITE PLASTISOL INkS




white plastisol

IMP.

TIF

LEX

22.1

0.20

12

WHITE plastisol range REFERENCE DENSITY PRINTABILITY TECHNICAL CHARACTERISTICS OEKOTEX 100/1

FC WHITE 3964012 1,6 OK NO

FC FLASH CURE 3964010 1,6 OK LAYER NO

FC EXTRA OPAQUE 3964078 1,5 NEED A GOOD KNOW-HOW VERY OPAQUE NO

FC MAT EXTRA OPAQUE 3964077 1,5 NEED A GOOD KNOW-HOW

VERY OPAQUE AND MAT NO

ELASTIC 3954000 1,59 OK ELASTICITY YES

KILIMANJARO 3954010 1,56 EASY BLUISH ASPECT

HIGH SPEED 3954011 1,62 NEED A GOOD KNOW-HOW

EXCELLENT FLASH CURE

CHARACTERISTICSYES

EVEREST 3954070 1,6 EASY VERY OPAQUE AND ESAY TO PRINT YES

OE WHITE 3934000 1,57 OK YES

OE ECLAIR 3934086 1,53 OK LAYER YES

OE EXTRA OPAQUE 3934082 1,6 NEED A GOOD KNOW-HOW VERY OPAQUE YES

COLOR LC 3Y1676 1,55 OK NO

THERMOFUSING PLASTISOL ADHESIVE 3864022 1.4 OK THERMIC STABILITY NO

SCREEN PRINTING


*

SPECIAL PRODUCT FOR TExTILE- glossy ELASTIC base- FLASHCOLOR Soft thinner base - FLASHCOLOR pearl base- PUFF transfer base- PLASTISOL expansible base- base for PLASTISOL shiners- glue for shiners- gelling agent- elastic white- FLASHCOLOR high opacity white- FLASHCOLOR matt high opacity white

Reference in 1 l: 3954091

This base retains its flexibility even in the case of large deposits. The quantity of product deposited will be a function of the mesh and the screen’s coated.The most interesting results are obtained using a cloth from 68 – 64 to 100 – 40 and 400 µ thick capillary films.This base can be used pure or in a mixture with Flashcolor ink, depending on the results required.

- Shiny transparent printing: In this case the shiny elastic base is used on its own. It gives different effects, for example the “plastic” varnish, drop of water effect, depending on the way in which it is deposited. It is polymerized at 160°C. The time it spends in the tunnel depends on the thickness deposited. For the transfer, use a mixture of the Flashcolor blending base + plastisol shiny base in a 70/30 ratio by weight. Application and transfer are done under the usual conditions. Depending on the paper used, the surface is either satin or glossy.

- “Tar” and anti-slip pin printing: If the shiny elastic base is mixed with Flashcolor or Oekoflash colours, it increases their shininess and elasticity. Once again, the extent of the deposit will depend on the screen’s coating. It is polymerised under the usual conditions taking the deposit into account.

- Shiny base and shiners printing: Shiners can be incorporated into the shiny base and the mixture screen printed on the cloth using a 10 to 21 threads/cm mesh screen depending on the particle size of the shiners used. It is polymerised under the usual conditions taking the deposit into account. Shiners can also be transferred using the following mixture by weight, for example:

- Flashcolor thinner base: 60 - glossy elastic base: 20 - shiners: 20 --- 100

The mixture applied to transfer paper, pregelled and transferred under the usual press conditions (temperature 170 - 190°C, 10 to 30 seconds action time and 3 to 5 bars pressure). Depending on the paper used, the surface is either satin or glossy.

- Elastic cloth printing: The glossy elastic base is mixed in a 30 to 40% ratio with a Flashcolor or Oekoflash ink.It is polymerized by passing through an IR tunnel (2 minutes at 160°C). The addition of 5% XD 150 catalyst reduces the polymerisation temperature by 15 to 20°C. The shiny elastic base is also used for printing in thick layers. It then preserves the flexibility of the printed areas. In this precise case, you are strongly recommended to use XD 150 hardener in order to ensure complete polymerisation.

Reference in 1 l: 3962006 - Reference in 5 l: 3964006

This thinner base reduces the viscosity of the ink and consequently its feel on the printed textile.It is mixed in a proportion of from 10 to 20% with the Flashcolor inks with the exception of the four-colour process tints. Usual polymerisation: 2 minutes at 160°C. It is not used alone.

glossy elastic base

FlashcoloR soFt thiNNeR base



This base gives a pearl effect to the ink applied.The Flashcolor ink is mixed with the pearl base in a maximum ration of 5%. It is used on a white ground and applied with a 21- 140 WPW screen.Usual polymerization: 2 min. at 160°C.


“Puff” transfers already exist in the U.S.A. but the “puff” base is an innovation because it allows screen printers to create their transfer plates themselves.This base is used blended with the inks or the Flashcolor base and must not make up more than half of the mixture.The mixture is then applied either directly on silicon coated paper or on the Flashcolor print already present on the transfer paper. The screen is chosen in accordance with the effect required.The “puff” transfer is pregelled under the usual conditions: 30 to 60 seconds at 105/110°C (to be determined by testing).

- Transfer conditions: - top plate temperature: 190°C - pressure: 5 to 6 bars - time: 4 to 10 seconds The transfer conditions are determined by testing. A compromise between expansion and solidity of the transfer must be found.

- Result:You get a pattern that stands out in relief with a smooth soft surface.The relief effects will be optimised by restrictions on the printing.


Mixed with a Flashcolor ink, this base gives a swollen (3D) effect to the ink after polymerisation.The mixture contains a maximum proportion of 50% base.Usual polymerisation: 2 min. at 160°C.The expanded volume is a function of the mesh used (traditional expansion: 21 threads).It is very important to determine a time and temperature according to your material in order to get the best expansion possible.


The shiners are mixed with the base in the following proportions : 80 g of base, 20 g of shiners.The preparation obtained is printed with a screen whose mesh is suited to the size of the shiners (foe example, 21 threads for 100 microns, 10 threads for 200 microns). Usual polymerisation: 2 min. at 160°C.

base FoR shiNeRs

plastisol expaNsible base

pUFF tRaNsFeR base

FlashcoloR peaRl base

glUe FoR shiNeRs

gelliNg ageNt

FlashcoloR matt high opacity white

FlashcoloR high opacity white

elastic white


The glue is applied with 14 to 36 threads/cm screens. The mesh count is chosen according to the textile substrate’s absorbency. The print is then sprinkled with shiners.At this stage, a calendaring of the surface increases the adhesion of the shiners. It is polymerised by passing through an IR tunnel (2 minutes at 160°C) or an oven.The screens are cleaned using solvent 2881 or 2899.

Reference in 1 kg: 3962097

To obtain a high density ink, mix the gelling agent with a Flashcolor ink in a proportion of 0.5 to 2% in weight. It must be agitated mechanically. The mixture obtained can be used after resting for 24 hours (time necessary for thickening).

Reference in 5 l: 3954000This glossy ink is used for applications on stretchy substrates.

Reference in 5 l: 3964078High cover glossy white. The opaqueness depends on the deposit of ink.Usual polymerisation (2 min. at 160°C).


High cover mat white. The opaqueness depends on the deposit of ink. It polymerisation has an effect on its appearance:

The recommended time and temperature for complete polymerisation are 2 min at 160°C. If a heavy deposit is made, it will obviously be necessary to increase the time of the pass at this temperature.

TIME TEMPERATURE RESULTAT2 min 110°C glossy look2 min 120°C matt look2 min 130°C slight expansion2 min 140°C very slight expansion2 min 150°C matt look2 min 160°C matt look2 min 170°C matt look2 min 180°C glossy look

Imag

es n

on c

ontra

ctue

lles

- IM

P. T

IFLE

X 11

.02.

2013



SCREEN PRINTING


*

UV INkSUVIPRIm CVInk with UV drying intended for printing on rigid PVC, self-adhesive supports and polycarbonate. It is also used for printing on PLV cardboard.


LEMON*

3452012 1 kg

GOLD YELLOW*

3452014 1 kg

ORANGE*

3452021 1 kg

SCARLET*

3452017 1 kg

CHERRY RED*

3452018 1 kg

CYCLAMEN*

3452041 1 kg

sTaNDarD coloUrsRef. Packaging Ref. Packaging

VIOLET*

3452043 1 kg

PROCESS BLUE*

3452051 1 kg

REFLEX BLUE*

3452025 1 kg

EMERALD GREEN*

3452061 1 kg

BLACK*

3452044 1 kg

THINNER WHITE*3452003 1 kgCOVERING WHITE3452002 1 kgEXTRA OPAQUE WHITE3452005 1 kg

4-COLOURS PROCESS

4-CoLoURS yELLow3452081 1 kg

4-CoLoURS mAgENTA3452084 1 kg

4-CoLoURS CyAN3452085 1 kg

4-CoLoURS BLACk3452086 1 kg

4-CoLoURS ThINNER BASE3452080 1 kg

Ref. Packaging

FlUo

FLUO YELLOW3452091 1 kg

FLUO ORANGE3452093 1 kg

FLUO RED3452094 1 kg

FLUO PINK3452095 1 kg

FLUO GREEN3452096 1 kg

Ref. Packaging

aDDITIvEs

TEXTURE VARNISH3454098 5 l

CATALYST3822090 1 l

Ref. Packaging

BasE


Ref. Packaging

UvIPrIM cvInk with UV drying intended for printing on rigid PVC, self-adhesive supports and polycarbonate. It is also used for printing on PLV cardboard.

¾¾ Appearance: glossy¾¾ Average density: 1.05¾¾ Viscosity: 3.5 ± 0.5 Pa.s¾¾ Covering power: poor except WHITE and BLACK ¾¾ Coverage rate: 100 m²/kg with a 180 -31 mesh¾¾ Weather resistance: good¾¾ Light fastness: very good¾¾ Thinner: 31960 max. 5 %¾¾ Cleaning solvents: 2881, 2891 NS-81 and NS-91¾¾ Expiry: refer to the label

The UViprim CV inks are used at standard viscosity or slightly diluted (5 %) and printed with mesh from 150 to 180 fibres/cm.To obtain correct opacity, we recommend you to add from 10% to 20 % of THINNER WHITE to the basic colours. COVERING WHITE or EXTRA OPAQUE WHITE cannot be mixed with other colours and are printed as a single colour.The textured varnish gives a grained finish on front sides and polycarbonate and polyester keyboards. This varnish will be diluted with 10 % of solvent 31960 and printed with a mesh from 77 to 90 fibres/cm.For Priplak® and Akilux® type Corona treated polypropylene, mix the ink with 5% catalyst 3822090 (representing 5% of the ink weigh).Since the Corona treatment has a limited lifetime, please check the surface condition of the substrate before printing.

The UViprim CV inks comply with EN 71-3 standard.Storage duration: 18 months in its original packaging, between 10 and 30°C, stored away from any source of heat and out of direct sunlight.

sPEcIFIcaTIoNs

sToragE aND ToxIcologY UsE

PolYMErIZaTIoNThe polymerization speed depends on several parameters, particularly the printed thickness, the opacity, the colour and the type of support, the type and number of UV lights.Due to the various configurations proposed, tests are required before starting prining.The white colour and the tints (containing white) cure more slowly.To obtain a good adherence, the ink must be polymerized correctly. For superposition of layers, the 1st layer must not be overpolymerized.In addition, the adherence between the various colours must be checked from time to time during the process.

MP.

TIF

LEX

28.0

1.20

13



SCREEN PRINTING


*

UV INkSUVIPRIm VYUV curing ink intended for printing on rigid PVC, self-adhesive supports and polycarbonate. It is also used for printing on PLV cardboard.

NVP Free


LEMON*

38C2002 1 kg

38C4002 5 kg

GOLD YELLOW*

38C2004 1 kg

38C4004 5 kg

ORANGE*

38C2006 1 kg

38C4006 5 kg

SCARLET*

38C2007 1 kg

38C4007 5 kg

CHERRY RED*

38C2008 1 kg

38C4008 5 kg

CYCLAMEN*

38C2014 1 kg

38C4014 5 kg

UvIPrIM vYUV curing ink intended for printing on rigid PVC, self-adhesive supports and polycarbonate.It is also used for printing on PLV cardboard.

¾¾ Appearance: glossy¾¾ Average density: 1.05¾¾ Viscosity: 3.5 ± 0.5 Pa.s¾¾ Coverage rate: 90 m²/kg with a 165 -34 mesh¾¾ Weather resistance: good¾¾ Light fastness: very good¾¾ Specific resistance: alcohol, petrol¾¾ Thinner: 3194058 max. 5 %¾¾ Cleaning solvents: 2881, 2891 NS-81 and NS-91¾¾ Expiry: refer to the label

The UViprim VY range is intended for printing on rigid PVC, self-adhesive foils, polycarbonate, paper and cardboard..Good results have been obtained on pre-treated polypropylene like Priplak® or Akylux by mixing the ink with 5% of hardener.The mixture is stable for 12 hours at 20°C.The efficiency of the hardener can be observed 24 hours after printing.Since the Corona treatment has a limited lifetime, please check the surface condition of the substrate before.Ready to use, we recommend a mesh between 140 to 180 threads/cm.To obtain correct opacity, we recommend you to add from 10% to 20 % of THINNER WHITE to the basic colours. COVERING WHITE or EXTRA OPAQUE WHITE cannot be mixed with other colours and are printed as a single colour.

The UViprim VY inks comply with EN 71-3 standard.Storage duration: 1 year in its original packaging, between 10 and 30°C, stored away from any source of heat and out of direct sunlight.The UViprim VY do not contain vinyl pyrrolidone.

sPEcIFIcaTIoNs

sToragE aND ToxIcologY UsE

PolYMErIZaTIoNThe polymerization speed depends on several parameters, particularly the printed thickness, the opacity, the colour and the type of support, the type and number of UV lights.Due to the various configurations proposed, tests are required before starting prining.The white colour and the tints (containing white) cure more slowly.To obtain a good adherence, the ink must be polymerized correctly. For superposition of layers, the 1st layer must not be over polymerized.In addition, the adherence between the various colours must be checked from time to time during the process.

MP.

TIF

LEX

28.0

1.20

13

Non contractual colours and picturesOn simple request, we can propose you a color panel card displaying accurate shades. BP 3 - 01450 PONCIN - France

International Sales : Tel. +33 (0) 4 74 37 33 80/97 - Fax +33 (0) 4 74 37 33 62 - [email protected] - www.tiflex.com

sTaNDarD coloUrsRef. Packaging Ref. Packaging

VIOLET*

38C2016 1 kg

38C4016 5 kg

PROCESS BLUE*

38C2027 1 kg

38C4027 5 kg

REFLEX BLUE*

38C2025 1 kg

38C4025 5 kg

EMERALD GREEN*

38C2033 1 kg

38C4033 5 kg

BLACK*

38C2044 1 kg

38C4044 5 kg

THINNER WHITE*38C2085 1 kg38C4085COVERING WHITE38C2087 1 kg38C4087EXTRA OPAQUE WHITE38C2080 1 kg38C4080

4-COLOURS PROCESSRef. Packaging

FlUo

FLUO YELLOW38C2070 1 kg38C4070 5 kgFLUO ORANGE38C2073 1 kg38C4073 5 kgFLUO RED38C2071 1 kg38C4071 5 kgFLUO PINK38C2074 1 kg38C4074 5 kgFLUO GREEN38C2072 1 kg38C4072 5 kg

Ref. Packaging

aDDITIFs

CATALYST3822090 1 l

Ref. Packaging

BasE

THINNER BASE38C2066 1 kg38C4066 5 kg

Ref. Packaging

4-CoLoURS yELLow38C2050 1 kg38C4050 5 kg4-CoLoURS mAgENTA38C2052 1 kg38C4052 5 kg4-CoLoURS CyAN38C2054 1 kg38C4054 5 kg4-CoLoURS BLACk38C2056 1 kg38C4056 5 kg4-CoLoURS ThINNER BASE38C2057 1 kg38C4057 5 kg

NVP Free

SCREEN PRINTING


*

UV INkSUVIPRIm ÉCO PLUSInk with UV drying dedicated for printing on papers, cardboards, PVC for PLV. NVP FREE.

NVP

FREE

Ink with UV drying dedicated for printing on papers, cardboards, PVC for PLV. NVP FREE.

UvIPrIM Éco PlUs

¾¾ Appearance: glossy

¾¾ Average density: 1.15

¾¾ Viscosity: 5 ± 1 Pa.s

¾¾ Coverage rate: 100 m²/kg with a 150 - 31 mesh

¾¾ Weather resistance: good

¾¾ Light fastness (scale from 1 to 8): very good except for indoor applications

¾¾ Thinner: 31970NG (without NVP): 10% max.

¾¾ Cleaning solvents: 2881, 2891, NS-81 and NS-91


SPECIFICATIONS POLYMERISATION

USEUViprim ECO Plus ink has been formulated in order to print on the following sustrates: • vinyl adhesive • paper, cardboard • supple and stiff PVC • treated polypropylen Priplak type (with 10% of hardener 3822090).The new UViprim Eco Plus ink allows multi layer printings without weakening the substrate.Main characteristics are: • ready to use inks • highly glossy • high reactivity • large suppleness allowing the cutting in the ink film • good resistance from outside

STORAGE AND TOXICOLOGYThe UViprim Eco Plus inks comply with EN 71-3 standard.Storage duration: 1 year in its original packaging, between 10 and 30°C, stored away from any source of heat and out of direct sunlight.

The opaque white must be used alone whereas, diluting white can be used with other colourings with a 10 to 20% rate in order to get a correct opaqueness. The UViprim Eco Plus ink is used at delivery viscosity or slightly diluted, with 150-34 fabrics. The line colours polymerise between 20 and 40 m/min on PVC, in 150-34 under an 80 W/cm lamp.On paper, under the same conditions, the passage speeds are halved.As the chemical reaction continues, it is better not exceed 24 hours between each layer.Moreover, adherence between the different colours,sometimes, must be check.The polymerization speeds depends on the thickness deposited, the colour and the type of substrate, the type and number of UV lamps.Due to the various printing configurations, it will better to perform some tests.Good results have been obtained on Priplak® and Akilux® treated polypropylene by mixing the ink with 10% of hardener 3762060. Since the Corona treatment has a limited lifetime, check the surface condition of the substrate before printing. The mix combining the ink and the hardener mix is stable during 8 hours.Adherence and scratch resistance will be obtained after 24 hours (you must make some test before working on long runs of printings).

COMPLEMENTARY PRODUCTSPhotoinitiator 3X6717: it improves the adherence with a better drying depth of the ink film.It can be use with all of the colours excepted the opaque white and the thinner base with a 1% to 5% weight proportions.Photoinitiator 3X8907: it improves the surface’s hardness and allows to increase the brightness. Required ratio : 1% to 4 % of the ink weigh.

NVP FREE


sTaNDarD coloUrs For oUTDoor aPPlIcaTIoN

RESIST LEMON YELLOW

3844002RNG 5 kg

GOLD YELLOW

3844004NG 5 kg

RESIST ORANGE

3844006RNG 5 kg

RESIST SCARLET

3844007RNG 5 kg

RESIST RED

3844008RNG 5 kg

CYCLAMEN

3844014NG 5 kg


VIOLET

3844016NG 5 kg

BLUE

3844022NG 5 kg

ROYAL BLUE

3844028NG 5 kg

EMERALD GREEN

3844033NG 5 kg

BLACK

3844044NG 5 kg

sTaNDarD coloUrs For INDoor aPPlIcaTIoN

LEMON YELLOW

3844002NG 5 kg

ORANGE

3844006NG 5 kg

SCARLET

3844007NG 5 kg

RED

3844008NG 5 kg

GREEN

3844032NG 5 kg

THINNER WHITE

3844000NG 5 kg



IMP.

TIF

LEX

28.

01.2

013.

Non

con

trac

tual

col

ours

and

pic

ture

s.


4-CoLoURS yELLow3844050NG 5 kg3846050NG 25 kg

4-CoLoURS mAgENTA3844052NG 5 kg3846052NG 25 kg

4-CoLoURS CyAN3844054NG 5 kg3846054NG 25 kg

4-CoLoURS BLACk3844056NG 5 kg3846056NG 25 kg

4-CoLoURS ThINNER BASE3844057NG 5 kg3846057NG 25 kg

Ref. Packaging

oPaQUE

OPAQUE WHITE3844080NG 5 kg

OPAQUE BLACK3844081NG 5 kg

Ref. Packaging BasE

THINNER BASE3844058NG 5 kg

Ref. Packaging

aDDITIvE

CATALYST3822090 1 l

Ref. Packaging


SCREEN PRINTING


*

UV INkSUVIPRIm FLInk with UV drying dedicated to printings on rigid or semi-rigid bottles of flamed polyethylene or polypropylene. NVP FREE.

NVP FREE


NVP FREE

UvIPrIM FlInk with UV drying dedicated to printings on rigid or semi-rigid bottles of flamed polyethylene or polypropylene. NVP FREE.

¾¾ Covering power: 80 m²/kg with a 165 – 34 fabric¾¾ Resistance to light: very good¾¾ Cleaning solvents: 2881, 2891 and NS91

ProPErTIEsGlossy finishHighly reactiveRheology suitable for high printing speedsExcellent stability in the screen

sUBsTraTE TrEaTMENTUViprim FL is formulated to print on PE and PP used in the bottle industry. The surface tension is very low, it is necesarry to flame the substrate before printing (minimum 42mN/m). The surface to be printed needs to be clean without grease particles

The UViprim FL inks comply with EN 71-3 standard.Storage duration: 1 year in its original packaging, between 10°C and 30°C. They must be stored away from a source of heat and out of direct sunlight.

sPEcIFIcaTIoNs


PolYMErIZaTIoNUViprim FL is a highly-reactive single-component ink. Under a lamp of 160 – 200 W/cm, the ink cures at a rate of between 2500 and 4000 units per hour.The tape resistance test should only be performed after the complet cooling of the bottle at ambient temperature.The overlaying of colours must be done in line on multi-colour printing machine.Adding 5% of hardener (representing 5% of the ink weigh) improves water resistance and solvents resistance, as well as encouraging a better adherence to difficult substrates. The effectiveness of the hardener can be observed 24 hours after printing.The combination of the ink and the hardener mixture stable for 8 hours.The speed of curing depends on numbers of parameters, including the thickness deposited and the opacity, colour and nature of the substrate.Due to the various printing configurations, testing is essential before each new printing run.Screens:The mesh required will be from 140 to 180 threads/cm.Dilution:UViprim FL inks are ready to use. If the viscosity nevertheless needs to be reduced, the required thinners will be:31960 ( with NVP ): maximum 5%31965 ( without NVP ): maximum 5%

sTaNDarD coloUrs

LEMON*

3762002 1 kg

GOLD YELLOW*

3762004 1 kg

ORANGE*

3762006 1 kg

SCARLET*

3762007 1 kg

CHERRY RED*

3762008 1 kg

CYCLAMEN*

3762014 1 kg


Ref. Packaging

Ref. Packaging

VIOLET*

3762016 1 kg

PROCESS BLUE*

3762027 1 kg

REFLEX BLUE*

3762025 1 kg

EMERALD GREEN*

3762033 1 kg

BLACK*

3762044 1 kg

THINNER WHITE*3762085 1 kg

oPaQUE

OPAQUE WHITE3762080 1 kg

OPAQUE BLACK3762081 1 kg

BasE


aDDITIvE

CATALYST3822090 1 kg

MP.

TIF

LEX

03.0

6.20

13



SCREEN PRINTING


*

UV INkSUVIPRIm GLThe mono-component UViprim GL range is based on a DUAL CURE system (UV light + hot air). It is dedicated to a high speed screen printing on glass, with or without coating, for interior use.NVP FREE.

NVP FREE



NVP FREE



¾¾ Viscosity: 2 - 3 Pa.s

¾¾ Opacifying power: • Coloriflex system: low • Opaque inks: excellent • White, black: excellent

¾¾ Coverage rate: 75 m²/kg with a 100 mesh

¾¾ Thinner: 31965, 5 % maxi

¾¾ Cleaning solvent: 2891, 2899, NS-91 and NS-99


The mono-component UViprim gL range is based on a DUAL CURE system (UV light + hot air). It is dedicated to a high speed screen printing on glass, with or without coating, for interior use. The dual cure system makes these inks insensitive with the extra thickness obtained on objects having a broad dimensional tolerance. most of all, Uviprim gL inks are shinny, opacity, highly reactivite and chemically resistant. NVP FREE.

UvIPrIM gl

SPECIFICATIONS USEPreparation of ink: This ink is ready to use. However, some adjustments may be necessary according to the conditions for application and the desired aspect:THINNER : 5% maxi.CUTTING BASE: its use in inks to dilute the colour while it increases the transparency and the reactivity of the mix as well.OPALESCENT BASE: its use in inks to dilute the colour while increasing the reactivity and opalescence by transmission with a loss of brilliance.METALLIC INKS: to use the diluting base with our metallic pastes in a 85/15 or 80/20 proportion. The pot-life of the blend is of 4 hours.Choice of the mesh:Directly function of the printing speed and the required opacity. Generally, we will use a 165, 150, 140 down to 120 mesh fabric tended to 16N. The diameter of the wire will be selected to obtain the best compromise between the deposit, the solidity and the definition.our inks can stand heavy cycles of dishwashing, alcohols tests and g1 test blend.

SUPPORTS AND PRETREATMENTSThe quality of glass and its chemical structure are related to its manufacturing method. Its surface quality will have to be perfect i.e. free from release agent or any other residue (finger marks, dust, grease, silicone etc).Untreated glass:A flame treatment (surface tension > 44 mN/m) according to the UVitro® process (trade mark of ISIMAT GmbH) is necessary to obtain maxi-mum performances.Coated glass:Many glass containers are covered with a water or solvent-based coating to modify the surface aspect (colour, opalescent, scratch resis-tance…): a flame treatment, right before printing, is then essential to obtain a sufficient surface tension and thus a good adherence.

POLYMERIZATIONBeing based on a DUAL CURE system, this ink dries in two steps: under UV light, to obtain a dry ink surface and to authorize the immediate overprinting of it, and with hot air to obtain optimal chemical and physical resistances.UV DRYING: at a printing speed of 3600 prints/h, use a lamp of 180-200W/cm minimum.HOT AIR DRYING: only one 20 min at 165°C passage for the whole of the decoration.The performances of the system are function of the material and the products used. Its industrial validation is imperative before final produc-tion run.

STORAGE AND TOXICOLOGYThe UViprim GL inks comply with EN 71-3 standard.

sTaNDarD coloUrs colorIFlEx sYsTEM

LEMON

3782002 1 kg

GOLD YELLOW

3782004 1 kg

ORANGE

3782006 1 kg

SCARLET

3782007 1 kg

RED

3782008 1 kg

CYCLAMEN

3782014 1 kg


VIOLET

3782016 1 kg

BLUE

3782020 1 kg

ROYAL BLUE

3782028 1 kg

GREEN

3782032 1 kg

ExTra oPaQUE

OPAQUE LEMON

3782082 1 kg

OPAQUE ORANGE

3782083 1 kg

OPAQUE RED

3782084 1 kg

OPAQUE GREEN

3782085 1 kg

OPAQUE BLACK

3782081 1 kg

Ref. Packaging

OPAQUE WHITE

3782080 1 kg

Non contractual colours and pictures

4-COLOURS PROCESS





Ref. Packaging

TINTINg

TINTING WHITE3782042 1 kg

TINTING BLACK3782044 1 kg

Ref. Packaging

BasE


Ref. Packaging

aDDITIvEs

OPALESCENT VARNISH3782068 1 kg

ETCHING VARNISH3782069 1 kg

WINDOW VARNISH3782067 1 kg

GELIFYLING AGENT3952061 1 kg

Ref. Packaging

IMP.

TIF

LEX

28.

01.2

013.

Non

con

trac

tual

col

ours

and

pic

ture

s.

Also available in metallic, pearlescent, fluorescent, iridescent,two-tones, etc ... shades. Please, contact us for details.




SCREEN PRINTING


*

UV INkSUVIPRIm mSUV drying ink designed for PVC self-adhesive printing, rigid PVC, polystyrene, treated polyester and polycarbonate. NVP FREE.

NVP FREE


NVP FREE

sTaNDarD coloUrs

LEMON*

3794002 5 kg

GOLD YELLOW*

3794004 5 kg

ORANGE*

3794006 5 kg

SCARLET*

3794007 5 kg

CHERRY RED*

3794008 5 kg

CYCLAMEN*

3794014 5 kg


Ref. Packaging

VIOLET*

3794016 5 kg

PROCESS BLUE*

3794027 5 kg

REFLEX BLUE*

3794025 5 kg

EMERALD GREEN*

3794033 5 kg

BLACK*

3794044 5 kg

UvIPrIM MsUV drying ink designed for PVC self-adhesive printing, rigid PVC, polystyrene, treated polyester and polycarbonate. NVP FREE.

¾¾ Appearance: glossy¾¾ Viscosity: 5 ± 1 Pa.s¾¾ Coverage rate: 100 m²/l with a 150 - 34 mesh¾¾ Light fastness: (scale from 1 to 8) good¾¾ Thinner: 31960 (with NVP)

31970 (without NVP)¾¾ Cleaning solvents: 2881, 2891, NS-81 and NS-91¾¾ Expiry: refer to the label

This ink is designed for UV self-adhesive PVC, rigid PVC, polycarbonate, polystyrene, treated Corona Priplak® type polypropylene sheet. 10% of catalyst 3822090 should be added for effective adhesion on certain kind of plastics.The UVprim MS ink is used at a standard viscosity or slightly diluted with mesh in the screen mesh 150 to 180 fibres/cm.

The UViprim MS ins inks comply with EN 71-3 standard.Storage time: 18 months in its original packaging, between 10 and 30°C, when stored away from any source of heat and out of direct sunlight.

sPEcIFIcaTIoNs


UsE

PolYMErIZaTIoNCovering white is used alone as a white ink, whereas the thinner white can be mixed with other colours in a proportion of 10% to 20% to obtain the correct opacity.Fusion temperature speeds depend on the thickness deposited, the colour and the type of substrate, the type and the number of lamps.The colours polymerize between 10 and 20 m/min under a 120 W/cm lamp. The tints containing white, like grey cross-link more slowly.Faced with the variety of plastic substrates, a trial is crucial before going into production.

UsE oF caTalYsTGood results have been obtained on Priplak® by mixing the ink with 10% of catalyst.Moreover, on certain polyester or polystyrene adding 10% of catalyst gives excellent adherence.The ink & catalyst mixture is stable for 12 hours.Taking the reaction time into account, you have to wait 24 to 48 hours to obtain the best adherence and nail resistance.


COVERING WHITE

3794087 5 kg

4-COLOURS PROCESS





aDDITIvE

MAT VARNISH3794059 5 kg

GLOSS VARNISH3794058 5 kg

CATALYST3822090 1 l

MP.

TIF

LEX

28.0

1.20

13



SCREEN PRINTING


*

UV INkSUVIPRIm PSInk with UV drying, NVP-free, intended for printing on rigid supports such as PVC, various types of polystyrene (high-impact, acrylic resin coated) and its derivates SAN, AbS. NVP FREE.

NVP FREE


NVP FREE

UvIPrIM PsInk with UV drying, NVP-free, intended for printing on rigid supports such as PVC, various types of polystyrene (high-impact, acrylic resin coated) and its derivates SAN, ABS.Suitable on rigid polycarbonate, it also has applications in the bottle industry. NVP FREE.

¾¾ Appearance: gloss¾¾ Average density: 1.05¾¾ Viscosity: 8 ± 2 Pa.s¾¾ Coverage rate: 100 m²/kg with a 150 - 34 mesh¾¾ Light fastness: very good¾¾ Weather resistance: good¾¾ Thinner (max. 10 %): 31965 (without NVP)

31960 (with NVP)¾¾ Cleaning solvents: 2881, 2891, NS-81 and NS-91¾¾ Expiry: refer to the label

The UViprim PS inks are used at standard viscosity or slightly diluted with mesh screens (150 to 180 fibres/cm).To obtain correct opacity, we recommend you to add from 10% to 20% of THINNER WHITE to the basic colours, WHITE 3802000 must be used alone as white ink.

PolYMErIZaTIoNThe fusion temperature speed depends on several parameters, especially the thickness deposited, the opacity, the colour and the type of substrate.Faced with the numerous installations proposed, tests are essential whenever starting to print.The white and the tints containing white colour will cure more slowly.To obtain good adherence, the ink must polymerized correctly.For superposition, the 1st layer must not be overpolymerized. In addition, the adherence between the various colours must be checked from time to time.

The UViprim PS inks comply with EN 71-3 standard.They are non-flammable (high flash point).Storage duration: 2 years in its original packaging, between 10°C and 30°C. They must be stored away from a source of heat and out of direct sunlight.

sPEcIFIcaTIoNs


UsE

sTaNDarD coloUrs

LEMON*

3802002 1 kg

GOLD YELLOW*

3802004 1 kg

ORANGE*

3802006 1 kg

SCARLET*

3802007 1 kg

CHERRY RED*

3802008 1 kg

CYCLAMEN*

3802014 1 kg


VIOLET*

3802016 1 kg

PROCESS BLUE*

3802027 1 kg

REFLEX BLUE*

3802025 1 kg

EMERALD GREEN*

3802033 1 kg

BLACK*

3802044 1 kg


WHITE

3802000 1 kg

4-COLOURS PROCESS





4-CoLoURS ThINNER BASE3802057 1 kg

Ref. Packaging

BasE


Ref. Packaging

MP.

TIF

LEX

28.0

1.20

13



SCREEN PRINTING


*

SOLVENT INkSAkILORGlossy air drying ink intended for printing E-flute polypropylene (Akylux®).

¾¾ Appearance: glossy except for fluo colours

¾¾ Smell: few

¾¾ Average density: 1.10


¾¾ Drying:

• air 15 min. at 20°C with a120 - 34 mesh

• pulsed air tunnel 30 s at 50/55°C with a 120 - 34 mesh

¾¾ Covering power by opacity: good to very good for black and white


¾¾ Weather resistance: good except for fluo colours

¾¾ Special resistance: oil, grease

¾¾ Solvents:

• thinner 4909 or 2899 (antistatic effect)

• retarder 4900 or propygel

¾¾ Cleaning solvent:

• manual 2881 2891, 2899, NS-81, NS-91, NS-99 and NS-100

• washer 2899, NS-81, NS-91, NS-99, and NS-100


glossy air drying ink intended for printing E-flute polypropylene (Akylux®), treated by Corona effect (since the duration of this treatment is limited, carry out preliminary tests).

akIlor

SPECIFICATIONS USEAKILOR inks are printed on pre-treated polypropylene sheets, used for outdoor short and medium duration signs: construction site panels, display racks, etc.10 to 30% matting base must be added, depending on the required finish.The mixture Thinner Base/Gold Paste No. 1, 2 and 3 is stable max. 48h.Do not use antistatic agents with these inks; if necessary, use thinner 2899 which will produce this effect. AKILOR inks suit to the printing of fragile plastics as SAC (Styrene Acrylonitrile Copolymer) (preliminary tests recommended).

STORAGE AND TOXICOLOGYThe AKILOR inks inks comply with EN 71-3 standard.

T E C H N O L O G I C A L & I N D U S T R I A L S O L U T I O N S S C R E E N P R I N T I N GOnly our Web-site is authorised to give real-time information about our inks. Paper notices are considered unwritten and no longer engage our company’s responsibility once they are updated on our Web-site. Our responsibility can be engaged only if the customer has based his position on the information published on our Web-site. In all cases, the user should carry out validation tests under his own conditions before using our inks for his production. The safety data sheets are available free at: www.tiflex.com/fds

sTaNDarD coloUrs oP

LEMON OP*

3882002 1 kg

GOLD YELLOW OP*

3882004 1 kg

ORANGE OP*

3882006 1 kg

CHERRY RED OP*

3882008 1 kg

CARMINE RED OP*

3882013 1 kg

CYCLAMEN OP*

3882014 1 kg


VIOLET OP*

3882016 1 kg

MEDIUM BLUE OP*

3882022 1 kg

DEEP BLUE OP*

3882026 1 kg

ROYAL BLUE OP*

3882024 1 kg

MEDIUM GREEN OP*

3882032 1 kg

DEEP GREEN OP*

3882034 1 kg

BROWN OP*

3882042 1 kg

BLACK OP*

3882044 1 kg

WHITE OP*3882000 1 kg




ThIXo 4-CoLoURS yELLow3882050 1 kg

ThIXo 4-CoLoURS mAgENTA3882052 1 kg

ThIXo 4-CoLoURS CyAN3882054 1 kg

ThIXo 4-CoLoURS BLACk3882056 1 kg

ThIXo 4-CoLoURS BASE3882057 1 kg

Ref. Packaging

FlUo

FLUO LEMON3882070 1 kg


FLUO GREEN3882072

Ref. Packaging

BasEs

OVERPRINT VARNIS AND THINNER BASE3882058 1 kg

MATTING BASE3882065 1 kg

Ref. Packaging

IMP.

TIF

LEX

28.

01.2

013

- Non

con

trac

tual

col

ours

and

pic

ture

s.


SCREEN PRINTING


*

SOLVENT INkSCELLULOSIQUE S.T.j.mat air drying ink intended for printing on polystyrene, A.b.S. and wood.


CELLULOSIqUE S.T.J.Matt air drying ink intended for printing on polystyrene, A.B.S. and wood.

¾¾ Appearance: matt¾¾ Average density: 1.35¾¾ Viscosity: 20 ± 2 Pa.s¾¾ Drying:

• air 20 to 30 min. at 20°C depending on the substrate¾¾ Covering power by opacity: good¾¾ Coverage rate: 35 m²/l with a 100 - 40 mesh¾¾ Weather resistance: medium¾¾ Solvents:

• thinner 4906 • retarder retargel or 9640¾¾ Cleaning solvents:

• manual 2881, 2891, 2899, NS-81, NS-91, NS-99 and NS-100 • washer 2881, NS-81, NS-91, NS-99, and NS-100¾¾ Expiry date: refer to the label

S.T.J. CELLULOSIQUE ink has been specially designed for the marking of polystyrene and its copolymers. It is recommended particularly for fine lines (graduation).It can possibly be used with pad printing equipment.Due to insufficient flexibility, it cannot be integrated in thermoforming.

The CELLULOSIQUE S.T.J. inks comply with EN 71-3 standard.

sPEcIFIcaTIoNs


UsE

sTaNDarD coloUrs

LEMON

3422015 1 l

GOLD YELLOW

3422022 1 l

CHERRY RED

3422036 1 l

MEDIUM BLUE

3422050 1 l

BRIGHT GREEN

3422057 1 l

BLACK

3422077 1 l

Ref. Packaging

WHITE

3422007 1 l

BasE

THINNER BASE AND OVERPRINT VARNISH3422084 1 l

Ref. Packaging

Ref. Packaging

IMP.

TIF

LEX

23.

01.2

013

. Non

con

trac

tual

col

ours

and

pic

ture

s.


SCREEN PRINTING


*

SOLVENT INkSEPOxY EV2-component ink offering excellent adherence on glass and metal and exceptional resistance to chemical agents. Not suitable for outdoor use. All colours are formulated with no silicone additive to allow silvering.


Catalyst Use Dose for use

2606

Thixotropic doesn’t reduce the viscosity of the inks.Idem XE 606.For glass with 2.5% agent 3320289:curing

of 30 mn at 160°C

Inks and mat base : 100 Catalyst : 10 Overprint varnish : 100 Catalyst : 15

XG 800 Gives build and improves the adherence in some difficult cases.


6969

The moire reactive with low temperatures, the more polyvalent. Metals and thermo hardeners. 2.5%

agent 3320289:curing of 30’ at 160°C: DISHWASHER PROOF.



¾¾ Average density: 1.20 for the OP colours and thixo four-colour process


¾¾ Drying:

• air 45 min. at 20°C

• air jet dryer 5 min. at 80°C (can be handled)

¾¾ Curing: 30 min. at 160°C (complete polymerization)

¾¾ Covering power by opacity: good

¾¾ Coverage rate: 45 m²/kg with a 100 -40 mesh

¾¾ Special resistance after polymerization: bases and solvents

¾¾ Solvents:

• thinner 2899

• retarder 4906, 4921 and NS-99

¾¾ Cleaning solvent:

• manual and washer 2899 and NS-99

¾¾ Expiry date: refer to the label

2-component ink offering excellent adherence on glass and metal and exceptional resistance to chemical agents. Not suitable for outdoor use. All colours are formulated with no silicone additive to allow silvering.

EPoxY Ev

SPECIFICATIONS USEMix the ink and the catalyst for 15 minutes before printing: pot life 16 hours.20 % to 30% of the matting base can be used, depending on the required finish.

STORAGE AND TOXICOLOGYThe EPOXY EV inks comply with EN 71-3 standard.

Ref. Packaging

oP

LEMON OP*

3322002 1 kg

GOLD YELLOW OP*

3322015 1 kg

ORANGE OP*

3322020 1 kg

CHERRY RED OP*

3322008 1 kg

CARMINE RED OP*

3322033 1 kg

CYCLAMEN OP*

3322030 1 kg


VIOLET OP*

3322035 1 kg

MEDIUM BLUE OP*

3322040 1 kg

DEEP BLUE OP*

3322045 1 kg

ROYAL BLUE OP*

3322050 1 kg

MEDIUM GREEN OP*3322032 1 kg

DEEP GREEN OP*

3322034 1 kg

BROWN OP*

3322060 1 kg

BLACK OP*

3322065 1 kg

WHITE OP*3322005 1 kg

sTaNDarD coloUrs

Ref. Packaging

COVERING WHITE

3322000 1 kg


IMP.

TIF

LEX

28.

01.2

013.

Non

con

trac

tual

col

ours

and

pic

ture

s.







Ref. Packaging

BasEs

THINNER BASE AND OVERPRINT VARNISH3322079 1 kg


Ref. Packaging

aDDITIvE

TENSION AGENT3262050 1 kg

Ref. Packaging

caTalYsT

CATALYST 26063320594 100 g

CATALYST 26063322094 1 kg

CATALYST XG 8003321097 200 g

CATALYST XG 8003322097 1 kg

CATALyST 69693320796 100 g

CATALyST 69693322096 1 kg

Ref. Packaging

aDDITIvE

ADHERENCE AGENT3320289 25 g

Ref. Packaging



SCREEN PRINTING


*

SOLVENT INkSFLUO PLASTIQUEAir drying ink intended for printing on flexible (tarpaulins) or rigid PVC, PmmA, polystyrene, polycarbonate and AbS.



IMP.

TIF

LEX

23.0

1.20

13- N

on c

ontr

actu

al p

ictu

res

The PLASTIC FLUO inks comply with EN 71-3 standard.

FlUo PlasTIQUE

Air drying ink intended for printing on flexible (tarpaulins) or rigid PVC, PMMA, polystyrene, polycarbonate and ABS.

¾¾ Average density: 1,05¾¾ Viscosity: 7 ± 1 Pa.s¾¾ Covering power by opacity: few¾¾ Coverage rate: 35 m²/l with a 100 - 40 mesh¾¾ Weather resistance: few¾¾ Light fastness: few¾¾ Solvent:

• thinner 4909 • retarder 4900 • brush 4909¾¾ Cleaning solvents:

• manual 2881, 2891, 2899, NS-81, NS-91, NS-99 and NS-100 • washer 2881, NS-81, NS-91, NS-99, and NS-100¾¾ Expiry: refer to the label

The PLASTIC FLUO inks are especially suitable for printing on rigid or flexible PVC (plates, tubes, sheets, PVC coated nylon and polyester cloth).In addition, they offer excellent adherence on polycarbonate, polymethyl methacrylate, ABS and polystyrene.They must be printed on white or on very light backgrounds.On flexible PVC, check that the «antiblocking» qualities of this ink are sufficient.

sPEcIFIcaTIoNs


UsE

FlUo

FLUO LEMON

3352060 1 l

FLUO ORANGE

3352066 1 l

FLUO RED

3352069 1 l

FLUO PINK

3352072 1 l

FLUO GREEN

3352075 1 l

Ref. Packaging

SCREEN PRINTING


*¾

SOLVENT INkSmATIFLExThin-film, fast-drying, matt ink, dedicated to print poster papers and cardboards.This ink has excellent behaviour in the screen.


MaTIFlExThin-film, fast-drying, matt ink, dedicated to print poster papers and cardboards.This ink has excellent behaviour in the screen.

¾¾ Appearance: matt¾¾ Average density: 1,04¾¾ Viscosity: 3.5 ± 1.5 Pa.s at 20°C¾¾ Drying:¾¾ • ambient air 10 min. at 20°C

• pulsed air tunnel 30 s at 50°C¾¾ Coverage rate: 65 m²/kg with a 120 - 34 mesh¾¾ Weather resistance: good¾¾ Light fastness: medium, 7 to 4 depending

on the colours¾¾ Solvents:

• thinner 4909 • retarder 4900 • semi-retarder gelified 4907¾¾ Cleaning solvents:

• manual 2881, 2891, NS-81, NS-91, NS-99 and NS-100 • washer 2899, NS-81, NS-91, NS-99, and NS-100¾¾ Expiry: refer to the label

The MATIFLEX inks comply with EN 71-3 standard.

sPEcIFIcaTIoNs sToragE aND ToxIcologY

sTaNDarD coloUrs

LEMON

3854002 5 kg

GOLD YELLOW

3854004 5 kg

ORANGE

3854006 5 kg

SCARLET

3854007 5 kg

RED

3854008 5 kg

CYCLAMEN

3854014 5 kg


VIOLET

3854016 5 kg

BLUE

3854022 5 kg

ROYAL BLUE

3854028 5 kg

GREEN

3854032 5 kg

DARK GREEN

3854034 5 kg

BLACK

3854044 5 kg






4-CoLoURS BASE3854057 5 kg

Ref. Packaging

WHITE3854000 5 kg

Ref. Packaging

Ref. Packaging

FlUo

FLUO YELLOW3854071 5 kg


IMP.

TIF

LEX

28.

01.2

013

lemon è yellow red è 485 2x royal blue è reflex blue

gold yellow è 116 cyclamen è rhodamine red green è 354

orange è 021 violet è violet dark green è green 2x

scarlet è warm red blue è process blue

Pantone® correspondance



SCREEN PRINTING


*

SOLVENT INkSmULTIFLExGlossy air drying ink intended for printing on flexible (tarpaulins), rigid and adhesive PVC, polymethyl methacrylate and polycarbonate.


The MULTIFLEX inks comply with EN 71-3 standard.

MUlTIFlExGlossy air drying ink intended for printing on flexible (tarpaulins), rigid and adhesive PVC, polymethyl methacrylate and polycarbonate. Gives glossy printing with excellent blocking resistance.

¾¾ Appearance: glossy¾¾ Average density: 1.10¾¾ Viscosity: 8 ± 2 Pa.s¾¾ Drying:

• ambient air 15 min. at 20°C • air jet dryer 30 s at 50°C¾¾ Covering power by opacity: good¾¾ Coverage rate: 50 to 60 m²/l with a 120 34 mesh¾¾ Special resistance: white gas¾¾ Weather resistance: good¾¾ Light fastness: good¾¾ Solvents:

• thinner 4905 • retarder 9640 • adhérence sur PVC souple 9640 • gun XC876 • brush 4903¾¾ Cleaning solvents:

• manual 2881, 2891, NS-81, NS-91, and NS-100 • washer 2881, 2899, NS-81, NS-99, and NS-100¾¾ Expiry: refer to the label¾¾ Special property: thermoformable

The MULTIFLEX inks, are particularly suitable for printing on rigid and flexible PVC (self-adhesive, plates, tubes, sheets, PVC coated cloth).They also display excellent adherence on polycarbonate and polymethyl methacrylate.Not suitable on polystyrene and ABS.On flexible unvarnished PVC, check that the antiblocking qualities of these inks are sufficient.10% to 20% matting base must be added, depending on the required finish.Multiflex white OP is not as flexible as the other colours in the range when very thick (more than 100 µm wet), check that the properties obtained are suitable.Can be used on all printing materials (manual, semi-automatic, automatic, roller to roller).

sPEcIFIcaTIoNs


UsE

sTaNDarD coloUrs oP

LEMON YELLOW OP*

3534002 5 kg

GOLD YELLOW OP*

3534004 5 kg

ORANGE OP*

3534006 5 kg

CHERRY RED OP*

3534008 5 kg

CARMINE RED OP*

3534013 5 kg

CYCLAMEN OP*

3534014 5 kg


VIOLET OP*

3534016 5 kg

MEDIUM BLUE OP*

3534022 5 kg

ROYAL BLUE OP*

3534024 5 kg

DEEP BLUE OP*

3534026 5 kg

MEDIUM GREEN OP*

3534032 5 kg

DEEP GREEN OP*

3534034 5 kg

BROWN OP*

3534042 5 kg

BLACK OP*

3534044 5 kg

THINNER BASE and overprint varnish anti-UV

3534058 5 kg

MATTING BASE

3534065 5 kg

IMP.

TIF

LEX

23.

01.2

013

WHITE OP*

3534000 5 kg



SCREEN PRINTING


*¾

SOLVENT INkSPATES mETALLIQUESTIFLEx already proposes, in the mat VINYLIQUES and SELECTACRYL series ready-to-use, highly stable, metallic inks.


Non

con

trac

tual

pic

ture

s - IM

P. T

IFLE

X 2

8.01

.201

3

PaTEs METallIQUEsTIFLEX already proposes, in the mat VINYLIqUES and SELECTACRYL series ready-to-use, highly stable, metallic inks.For the other series, we prefer to deliver, for stability reasons, metallic pastes and colourless bases in separate packages.The 2 components are mixed to obtain the same shades, and the quantities to be used can be prepared as required.

The base should be added to the paste while stirring.Recommended proportions:gold paste (1 or 3 or Copper) colourless paste (20 to 30 %) + (80 to 70 %)

silver paste colourless paste (20 to 25 %) + (80 to 75 %)

*The leafing silver paste gives a white glossy finish but it cannot be overprinted the non-leafing silver paste can be overprinted and does not powder on the surface.**The GOLD pastes have no stability with the URETHAL + standard catalyst.

GOLD URETHAL will be obtained by a coloring of the silver paste (contact us for more info).

sPEcIFIcaTIoNs

sPEcIal EFFEcT

GOLD Nº1**

3552015 1 l

goLD Nº3**

3552030 1 l

LEAFING SILVER*

3552075 1 l

SPARKLE SILVER

3552080 1 l

NoN-LEAFINg SILVER*

3552085 1 l

Ref. Packaging


SCREEN PRINTING


*

SOLVENT INkSPLAxOLORGlossy air drying ink dedicated to print on acrylic resin coated polystyrene, its copolymers and rigid and acrylic resin coated PVC. It is formulated for high speed printing with drying in air jet drying. It is thermoformable.


PlaxolorGlossy air drying ink dedicated to print on acrylic resin coated polystyrene, its copolymers and rigid and acrylic resin coated PVC. It is formulated for high speed printing with drying in air jet drying. It is thermoformable.

¾¾ Appearance: glossy¾¾ Smell: few¾¾ Average density: 1,05¾¾ Viscosity: 7 ± 1 Pa.s¾¾ Drying:

• ambient air 20 min. at 20°C • pulsed air tunnel 1 min. at 60°C with a 120 -34 mesh¾¾ Covering power: good¾¾ Coverage rate: 48 m²/kg with a 120 - 34 mesh¾¾ Special resistance: petrol¾¾ Weather resistance: good¾¾ Light fastness: good, 6 to 8 depending on the blue

scale¾¾ Solvents:

• thinner 4920 • drying activator 4905 • retarder 4960 or retargel or 9640 • gun XC 876¾¾ Cleaning solvents:

• manual 2881, 2891, NS-81, NS-91, NS-99, and NS-100 • washer 2881, NS-81, NS-91, NS-99 and NS-100¾¾ Expiry date: refer to the label¾¾ Special property: thermoformable

The PLAXOLOR ink is specific for printing on acrylic resin coated polystyrene and rigid and acrylic resin coated PVC.Can be used on polymethyl methacrylate and on polycarbonate, after preliminary tests.Do not use on flexible PVC (tarpaulin, leather goods, etc.) or on crystal polystyrene.10 to 20% matting base must be added, depending on the required finish.

The PLAXOLOR inks comply with EN 71-3 standard.

sPEcIFIcaTIoNs


UsE

IMP.

TIF

LEX

28.

01.2

013

sTaNDarD coloUrsoP

LEMON OP*

3392002 1 l

GOLD YELLOW OP*3392022 1 l

ORANGE OP*

3392007 1 l

CHERRY RED OP*

3392008 1 l

CARMINE RED OP*

3392033 1 l

CYCLAMEN OP*

3392034 1 l


VIOLET OP*

3392035 1 l

MEDIUM BLUE OP*3392040 1 l

DEEP BLUE OP*

3392042 1 l

ROYAL BLUE OP*

3392043 1 l

MEDIUM GREEN OP*3392048 1 l

DEEP GREEN OP*

3392051 1 l

BROWN OP*

3392058 1 l

BLACK OP*

3392055 1 l

WHITE OP*3392012 1 l

BasEs

THINNER BASE AND OVERPRINT VARNISH

3392060 1 l

MATTING BASE3392065 1 l

Ref. Packaging



SCREEN PRINTING


*

SOLVENT INkSPOLYCOLORGlossy air drying ink intended for printing on self-adhesive PVC, rigid, polymethyl methacrylate, AbS and some treated Polyesters.


¾¾ Appearance: high glossy

¾¾ Smell: few

¾¾ Average density: - 1.05 for the coloriflex system shades - 1.10 for the OP shades - 1.00 for the four colour shade


¾¾ Drying: • ambient air 15 min. at 20°C

¾¾ Covering power: - medium for the coloriflex system shades - good for the OP shades

¾¾ Coverage rate: 45 m²/kg with a 120 -34 mesh

¾¾ Special resistance: alcohol, petrol

¾¾ Weather resistance: - excellent for the coloriflex system and four-colour shades - good for the OP colours

¾¾ Light fastness: - excellent for the coloriflex system and four-colour shades - good for the OP colours

¾¾ Solvents: • drying activator 4905 • thinner 4945 • retarder retargel or 9640

¾¾ Cleaning solvents: • manual 2881, 2891, NS-81 and NS-91 • washer 2881, 2899, NS-81 and NS-91


¾¾ Special property: thermoformable

glossy air drying ink intended for printing on self-adhesive PVC, rigid, polymethyl methacrylate, ABS and some treated Polyesters.

PolYcolor

SPECIFICATIONS USEThe POLYCOLOR ink is mainly intended for printing on self-adhesive substrates.The COLORIFLEX system inks offer maximum light fastness and are there fore ideal for outdoor use.Depending on the required finish, 10 to 20% matting base can be used.

STORAGE AND TOXICOLOGYThe POLYCOLOR inks comply with EN 71-3 standard.

sTaNDarD coloUrs colorIFlEx sYsTEM

LEMON*

3992012 1 kg

GOLD YELLOW*

3992015 1 kg

ORANGE*

3992018 1 kg

SCARLET*

3992007 1 kg

CHERRY RED*

3992022 1 kg

CYCLAMEN*

3992024 1 kg

Ref. Packaging Ref. Packaging Ref. Packaging Ref. Packaging Ref. Packaging

VIOLET*

3992026 1 kg

BLUE*

3992030 1 kg

ROYAL BLUE*

3992032 1 kg

EMERALD GREEN*

3992034 1 kg

BLACK*

3992035 1 kg

WHITE*3992010 1 kg

oP

LEMON OP

3992041 1 kg

GOLD YELLOW OP

3992045 1 kg

ORANGE OP

3992048 1 kg

CHERRY RED OP

3992051 1 kg

CARMINE RED OP

3992053 1 kg

CYCLAMEN OP

3992052 1 kg

VIOLET OP

3992054 1 kg

MEDIUM BLUE OP

3992060 1 kg

DEEP BLUE OP

3992062 1 kg

ROYAL BLUE OP

3992064 1 kg

MEDIUM GREEN OP

3992056 1 kg

DEEP GREEN OP

3992067 1 kg

BROWN OP

3992069 1 kg








Ref. Packaging

BasEs

ThINNER BASE ANS ANTI-UV OVERPRINT VARNISH

3992005 1 kg


Ref. Packaging

IMP.

TIF

LEX

28.0

1.20

13 -

Non

con

trac

tual

col

ours

and

pic

ture

s



SCREEN PRINTING


*

SOLVENT INkSPOLYCOLOR ExTRA-OPAQUEmatt air drying ink intended for printing on polycarbonate and on polyester.This ink does not adhere to PVC and is not thermoformable.



The EXTRA-OPAQUE inks comply with EN 71-3 standard.

POLYCOLOR EXTRA-OPAqUEMatt air drying ink intended for printing on polycarbonate and on polyester. This ink does not adhere to PVC and is not thermoformable.Caution : POLYCOLOR EXTRA OPAqUE ink cannot be mixed with the POLYCOLOR standard serie.

¾¾ Appearance: matt¾¾ Average density: 1.35¾¾ Viscosity: 10 ± 2 Pa.s¾¾ Drying:

• air 15 min. at 20°C¾¾ Covering power by opacity: excellent¾¾ Coverage rate: 20 to 25 m²/kg with a 61 -64 mesh¾¾ Solvents:


• manual 2881, 2891, NS-81 and NS-91 • washer 2881, 2899, NS-81 and NS-91¾¾ Expiry: refer to the label

The EXTRA-OPAQUE inks are reserved as the last opacifying layer for the front sides of treated polycarbonate and polyester.

sPEcIFIcaTIoNs


UsE

ExTra oPaQUE coloUrs

EXTRA OPAQUE WHITE

3992040 1 kg

3994040 5 kg

EXTRA OPAQUE BLACK

3992065 1 kg

3994065 5 kg

Ref. Packaging

ATTENTIoN : ThE «EXTRA oPAQUE whITE» AND «EXTRA oPAQUE BLACk» ARE MAT

IMP.

TIF

LEX

28.0

1.20

13 -

Non

con

trac

tual

col

ours

and

pic

ture

s

SCREEN PRINTING


*

SOLVENT INkSPOLYTIFLExAir drying ink especially designed for printing on polyolefins (polyethylene and polypropylene) : crates, buckets, etc.


IMP.

TIF

LEX

28.0

1.20

13

The POLYTIFLEX inks comply with EN 71-3 standard.

PolYTIFlExAir drying ink especially designed for printing on polyolefins (polyethylene and polypropylene) : crates, buckets, etc.

¾¾ Appearance: satin¾¾ Average density: 1,18¾¾ Viscosity: 12 ± 2 Pa.s¾¾ Drying:

• air (20°C) dust dry: 1 h • dry 12 to 24 h¾¾ Covering power by opacity: good¾¾ Coverage rate: 50 m²/l with a 120 -34 mesh¾¾ Solvents:

• thinner 4909 • retarder 4900, propygel¾¾ Cleaning solvents:

• manual 2881, 2899, NS-81 and NS-99 • washer 2881, 2899, NS-81 and NS-99¾¾ Expiry date: refer to the label

The POLYTIFLEX ink is ideal for manual or low speed printing.To obtain excellent adherence, we recommend you to flame the substrate before printing.This ink should not be used for printing on thin films.

sPEcIFIcaTIoNs


UsE

sTaNDarD coloUrs

LEMON OP

3432002 1 l

GOLD YELLOW OP

3432004 1 l

ORANGE OP

3432006 1 l

CHERRY RED OP

3432008 1 l

PRIMARY BLUE 6140 OP

3432063 1 l

RoyAL BLUE 6135

3432054 1 l


DEEP GREEN OP

3432034 1 l

BLACK 6165

3432081 1 l

WHITE 6100

3432009 1 l

BasE

THINNER BASE 4720 AND OVERPRINT VARNISH3432090 1 l

Ref. Packaging

Non contractual colours and pictures BP 3 - 01450 PONCIN - FranceInternational Sales : Tel. +33 (0) 4 74 37 33 80/97 - Fax +33 (0) 4 74 37 33 62 - [email protected] - www.tiflex.com

SCREEN PRINTING


*

SOLVENT INkSPROPYLUxGlossy air drying ink intended for printing on polypropylene, frequently encountered as Akilux® and Priplak® brands. It can adhere to untreated polypropylene (use of bonding primer), but flaming or Corona treatment, when possible, further improves its performance.


ProPYlUxGlossy air drying ink intended for printing on polypropylene, frequently encountered as Akilux® and Priplak® brands. It can adhere to untreated polypropylene (use of bonding primer), but flaming or Corona treatment, when possible, further improves its performance.

¾¾ Appearance: glossy¾¾ Smell: few¾¾ Average density: 1,10¾¾ Viscosity: 8 ± 1 Pa.s¾¾ Drying:

• ambient air 15 min. at 20°C • air jet dryer 2 min. at 60°C¾¾ Covering power by opacity: good¾¾ Coverage rate: 50 m²/kg with a 120 - 34 mesh¾¾ Weather resistance: poor¾¾ Alcohol resistance: good¾¾ Light fastness: quite good¾¾ Solvents:

• thinner 4909 • retarder propygel or 4900¾¾ Cleaning solvents:

• manual 2881, 2899, NS-81 and NS-99 • washer 2899¾¾ Expiry date: refer to the label

The PROPYLUX ink was designed for printing on fluted or sheet polypropylene.These inks should not be used for printing on thin films (sheaths).The adhesion primer 3302070 improves the adherence of PROPYLUX ink on untreated substrates.If resistance to grease and/or sweating is required, it is essential to overprint the ink after drying with propylux varnish 3302075.10% to 20% matting base must be added, depending on the required finish.

The PROPYLUX inks comply with EN 71-3 standard.

sPEcIFIcaTIoNs


UsE

sTaNDarD coloUrs

LEMON

3302010 1 l

GOLD YELLOW

3302015 1 l

ORANGE

3302020 1 l

CHERRY RED

3302025 1 l

CYCLAMEN

3302047 1 l

VIOLET

3302030 1 l


MEDIUM BLUE

3302035 1 l

ROYAL BLUE

3302040 1 l

MEDIUM GREEN

3302045 1 l

BLACK

3302050 1 l

WHITE

3302005 1 l

ADhESIoN PRImER 3X1189

3302070 1 l

IMP.

TIF

LEX

28.

01.2

013

- Non

con

trac

tual

col

ours

and

pic

ture

s

THINNER BASE3302060 1 l

VERNISH3302075 1 l


SCREEN PRINTING


*

SOLVENT INkSSELECTACRYLGlossy air drying ink intended for printing on self-adhesive PVC, polymethyl methacrylate, AbS, polystyrene, paper and cardboard.


IMP.

TIF

LEX

28.

01.2

013

The SELECTACRYL inks comply with EN 71-3 standard.

sElEcTacrYlGlossy air drying ink intended for printing on self-adhesive PVC, polymethyl methacrylate, ABS, polystyrene, paper and cardboard.

¾¾ Appearance: glossy¾¾ Average density: 1,05¾¾ Viscosity: 10 ± 1 Pa.s¾¾ Drying:

• ambient air 15 min. at 20°C • air jet dryer 2 min. at 50°C¾¾ Covering power: medium for the Coloriflex system

good for white, black and metallized colours¾¾ Coverage rate: 50 m²/l with a 120 -34 mesh

38 m²/l with a 100 - 40 mesh¾¾ Weather resistance: excellent, good glossy retention¾¾ Light fastness: excellent, 7 to 8 depending on the

blue scale¾¾ Solvents:

• thinner 4920 or 4941 • drying activator 4905 • retarder 4960 or retargel or 9640 • adhesion 4903 • gun XC 876¾¾ Cleaning solvents:

• manual 2881, 2891, NS-81, NS-91, NS-99 and NS-100 • washer 2881, NS-81, NS-91, NS-99, and NS-100¾¾ Expiry: refer to the label

The SELECTACRYL ink, with its exceptionally bright shade and its semi-opaque appearance, is dedicated to printing on self-adhesive supports and illuminated signs.Generally, we recommend you to print on self-adhesive PVC, rigid PVC, polymethyl methacrylate, ABS and polystyrene.* 10% to 20 % matting base must be added, depending on the required finish.When printing on crystal polystyrene, it will be necessary to dilute with solvents 4941 and 4960 only.Not suitable on flexible PVC.

sPEcIFIcaTIoNs


UsE

sTaNDarD coloUrs

LEMON*

3372015 1 l

GOLD YELLOW*

3372020 1 l

ORANGE*

3372025 1 l

SCARLET*

3372007 1 l

CHERRY RED*

3372030 1 l

CYCLAMEN*

3372040 1 l


VIOLET*

3372045 1 l

BLUE*

3372050 1 l

ROYAL BLUE*

3372052 1 l

EMERALD GREEN*

3372055 1 l

BLACK*

3372060 1 l

sPEcIal EFFEcT

SPARKLE SILVER3372075 1 l

GOLD Nº13372065 1 l

Ref. Packaging

BasEs

THINNER BASE AND OVERPRINT VARNISH ANTI U.V.3372080 1 l


Ref. Packaging

WHITE*3372010 1 l



SCREEN PRINTING


*

SOLVENT INkSSICCATIVEIt is a glycerophtalic ink drying by oxidation.This ink is used to print on metal, glass and minerals.


sIccaTIvEIt is a glycerophtalic ink drying by oxidation. This ink is used to print on metal, glass and minerals.


• air (20°C) dust dry 2 to 3 h, dry 24h • oven dust free 1 h at 100°C¾¾ Covering power: excellent¾¾ Coverage rate: 44 m²/l with a 100 - 40 mesh¾¾ Weather resistance: good¾¾ Solvents:


• manual 2881, 2891, 289, NS-81, NS-91, NS-99 and NS-100 • washer 2899, NS-81, NS-91, NS-99 and NS-100¾¾ Expiry: refer to the label

SICCATIVE ink is used when good outdoor performance is required: on metals, etc.) and on minerals (slate, brick, ceramic, glass).For non-ferrous metals please contact us.

sPEcIFIcaTIoNs UsE

sTaNDarD coloUrs

LEMON OP

3412002 1 l

GOLD YELLOW OP

3412004 1 l

ORANGE OP

3412005 1 l

CHERRY RED OP

3412008 1 l

PRImARy BLUE 3302

3412006 1 l

RoyAL BLUE 3303

3412012 1 l


MID GREEN OP

3412032 1 l

DEEP GREEN OP

3412034 1 l

BLACk 3380

3412042 1 l

whITE 3405

3412048 1 l

THINNER BASE 4750

3412090 1 l

IMP.

TIF

LEX

28.0

1.20

13



SCREEN PRINTING


*

SOLVENT INkSTAmPOCOLORShiny pad printing ink (ambient drying) dedicated to printings on rigid PVC, polymethyl methacrylate, polycarbonate, polystyrene, aluminium.


¾¾ Aspect : Shiny



¾¾ Drying: • ambient air 1 mn • complete polymerization 72 hours

¾¾ Ink pot life and hardener: 8 hours

¾¾ Weather Resistance: average

¾¾ Light resistance: average

¾¾ Specific resistance: alcohol, petrol (with hardener)

¾¾ Solvents: • thinner 4920 • accelerator 4905

¾¾ Cleaning solvents: • manual 2881, 2891, NS-81, NS-91 and NS-99 • Washer 2881, NS-81, NS-91 and NS-99


Shiny pad printing ink (ambient drying) dedicated to printings on rigid PVC, polymethyl methacrylate, polycarbonate, polystyrene, aluminium. By using an hardener, both treated polypropylene and treated polyethylene can be printed.

TaMPocolor

SPECIFICATIONS USEFor difficult adherence on substrate or when a specific chemical adherence is required (alcohol resistance, petrol resistance, weather resistance) our TAMPOCOLOR ink will be combined with an hardener (representing 5% of the ink weigh).Pot life of the ink will be 8 hours at 20°C. In case of the increase of the ambient temperature, using time will be automatically reduced.Optimal performances will be obtained at least 72 hours after drying. Dilution to 15%.TAMPOCOLOR inks can be mixed together.

STORAGE AND TOXICOLOGYThe TAMPOCOLOR inks comply with EN 71-3 standard.

LEMON OP*

33A2002 1 kg

GOLD YELLOW OP*

33A2004 1 kg

ORANGE OP*

33A2006 1 kg

CHERRY RED OP*

33A2008 1 kg

CARMINE RED OP*

33A2013 1 kg

CYCLAMEN OP*

33A2014 1 kg

OPAQUE RED

33A2088 1 kg

OPAQUE LEMON

33A2082 1 kg

OPAQUE GREEN

33A2085 1 kg

Ref. Packaging

VIOLET OP*

33A2016 1 kg

MEDIUM BLUE OP*

33A2022 1 kg

DEEP BLUE OP*

33A2026 1 kg

MEDIUM GREEN OP*33A2032 1 kg

DEEP GREEN OP*

33A2034 1 kg

BLACK OP*

33A2044 1 kg

WHITE*3992010 1 kg

OPAQUE WHITE

33A2080 1 kg

oP coloUrs ExTra oPaQUE


IMP.

TIF

LEX

04.0

7.20

13 -

Non

con

tract

uals

pict

ures


4-CoLoURS yELLow33A2050 1 kg

4-CoLoURS mAgENTA33A2052 1 kg

4-CoLoURS CyAN33A2054 1 kg

4-CoLoURS BLACk33A2056 1 kg

Ref. Packaging

BasE

THINNER BASE OP*33A2066 1 kg

aDDITIvE

CATALYST33A0560 100 gr




SCREEN PRINTING


*

SOLVENT INkSURETHAL2-component polyurethane ink combining the properties of adherence on many substrates and remarkable resistance to light and UV.





¾¾ Drying: • ambient air can be handled after 75 min. can be stacked after 12 hours complete polymerisation after 72 hours • IR tunnel preliminary tests


¾¾ Special resistance: excellent to chemical products

¾¾ Weather resistance: excellent

¾¾ Light fastness: excellent

¾¾ Solvents: • thinner and brush 4904 or 4905 • retarder 4960 or 9640 • gun XC 876

¾¾ Cleaning solvents: • manual 2881, 2891, NS-81, NS-91, NS-99 and NS-100 • washer 2881, NS-81, NS-91, NS-99, and NS-100


¾¾ Special property: thermoformable

2-component polyurethane ink combining the properties of adherence on many substrates and remarkable resistance to light and UV.

UrEThal

SPECIFICATIONS USEThe URETHAL inks are mixed with URETHAL hardener in a ratio of 100 to 15 by weight, apart from WHITE which has a ratio of 100 to 10.The pot life of the mixture is more than 8 hours at 20°C.Higher temperatures reduce the pot life and the time of use.The final performance is obtained after at least 72 h drying.The URETHAL inks are miscible together.The screen must be cleaned immediately after printing.For brush application, dilute at 25% with thinner 4904.The thinner base is anti-UV.

STORAGE AND TOXICOLOGYThe URETHAL inks comply with EN 71-3 standard.

colorIFlEx sYsTEM

LEMON*

3572021 1 kg

GOLD YELLOW*

3572023 1 kg

ORANGE*

3572031 1 kg

SCARLET*

3572007 1 kg

CHERRY RED*

3572043 1 kg

CYCLAMEN*

3572051 1 kg


VIOLET*

3572053 1 kg

BLUE*

3572061 1 kg

ROYAL BLUE*

3572063 1 kg

EMERALD GREEN*

3572071 1 kg

BLACK*

3572081 1 kg

WHITE*3572011 1 kg


Non

con

tract

ual p

ictu

res

- IM

P. T

IFLE

X 04

.07.

2013







Ref. Packaging

BasEs

OVERPRINT VARNISH AND THINNER BASE3572091 1 kg


Ref. Packaging

aDDITIvEs

ADHERENCE AGENT3320289 25 g

URETHAL CATALYST3570803 150 g

URETHAL CATALYST3572003 1 kg

Ref. Packaging



SCREEN PRINTING


*

SOLVENT INkSVERNIS ANTI SALISSURE2-component cleanable protective varnish resistant to water-based and alcohol-based felt tip pens and Velleda® felt tip pens (CONTÉ). It is applied only as overprinting on mAT VINYL inks or on non acrylic resin coated PVC.



IMP.

TIF

LEX

28.0

1.20

13 -

Non

con

tract

ual p

ictu

res.

vErNIs aNTI salIssUrE2-component cleanable protective varnish resistant to water-based and alcohol-based felt tip pens and Velleda® felt tip pens (CONTÉ). It is applied only as overprinting on MAT VINYL inks or on non acrylic resin coated PVC.

¾¾ Appearance: high glossy¾¾ Average density: 1.05¾¾ Drying:

• dry stackable 24 h at 20°C minimum • polymeriaation 72 h at 20°C minimum¾¾ Pot life: > 8 h at 20°C¾¾ Coverage rate: 40 m²/l with a 90-48 mesh¾¾ Solvents:

• thinner 4905 • gun XC 876¾¾ Cleaning solvents:

• manual 2881, 2891, NS-81, NS-91, NS-99, and NS-100 • washer 2881, 2899, NS-81, NS-91, NS-99, and NS-100¾¾ Expiry date: refer to the label

15 min to 30 min. before printing, mix the varnish and the catalyst in the following proportions by weight: • varnish: 75 measures • 25 measuresAt this stage, the mixture can be used for 8 hours at 20°C.The anti-fouling varnish is applied only on MAT VINYL inks used in the manufacture of labels, of panels, time tables on PVC. For optimum results, we recommend you to use of a 90 - 48 mesh.Final resistance is obtained after 8 days at 20°C.I n case of a significant dilution, increase the deposit.

The anti-fouling varnish for erasable writing comply with EN 71-3 standard.

sPEcIFIcaTIoNs


UsE sTaNDarD coloUrs

ANTI-FoULINg VARNISh(750 g varnish + 250 g catalyst)

3352098 1 l

Ref. Packaging

SCREEN PRINTING


*

SOLVENT INkSCHROmO TRANSFER VARNISHEnamel based inks are printed on specific transfer paper.Chromo varnish is applied on the whole surface of decalcomania.After cooking, enamels are welding, the varnish sublimates and disapeared.



IMP.

TIF

LEX

28.0

1.20

13 -

Non

con

tract

ual p

ictu

res.

chroMo TraNsFEr varNIsh

Enamel based inks are printed on specific transfer paper.Chromo varnish is applied on the whole surface of decalcomania.After cooking, enamels are welding, the varnish sublimates and disapeared.

aDDITIvEs

YELLOW CHROMO TRANFER VARNISh 3800

3836020 25 l

INCOLORE CHROMO TRANSFER VARNISh 3915

3836030 25 l

Ref. Packaging

1450

1450

1450

1450Bradley Drive

SCREEN PRINTING


*

SOLVENT INkSVINYFLExGlossy air drying ink intended for printing on polycarbonate, AbS, hard PVC, polymethyl methacrylate and painted metal.


vINYFlExGlossy air drying ink intended for printing on polycarbonate, ABS, hard PVC, polymethyl methacrylate and painted metal.


• ambient air 12 min. at 20°C • air jet dryer 45 s at 50°C¾¾ Covering power: good¾¾ Coverage rate: 45 m²/kg with a 120 - 34 mesh¾¾ Special resistance: alcohol, petrol¾¾ Weather resistance: good¾¾ Light fastness: good¾¾ Solvents:

• thinner 4920 • drying activator 4905 • retarder 4960 or retargel • adhesion 9640 • gun XC 876 • brush 4903¾¾ Cleaning solvents:

• manual 2881, 2891, NS-81, NS-91, and NS-100 • washer 2881, NS-81, NS-91 and NS-100¾¾ Expiry: refer to the label¾¾ Special property: thermoformable

VINYFLEX ink is particularly recommended for printing on polycarbonate and whenever perfect resistance to alcohol and petrol on vinyl self-adhesives is required.This ink is suitable for thermoforming.10 to 30 % matting base must be added, depending on the required finish.Not suitable on flexible PVC.Adhesive 0380 is used to stick polycarbonate labels print with VINYFLEX ink.

The VINYFLEX inks comply with EN 71-3 standard.

sPEcIFIcaTIoNs


UsE

sTaNDarD coloUrs

LEMON OP

3482002 1 l

GOLD YELLOW OP3482005 1 l

ORANGE OP

3482006 1 l

CHERRY RED OP

3482009 1 l

3484009 5 l

CARMINE RED OP

3482013 1 l

CYCLAMEN

3482048 1 l


VIOLET

3482052 1 l

LIGHT BLUE

3482056 1 l

PRIMARY BLUE

3482024 1 l

DEEP BLUE

3482028 1 l

ROYAL BLUE

3482060 1 l

MEDIUM GREEN OP3482033 1 l

DEEP GREEN OP

3482034 1 l

BROWN

3482080 1 l

BLACK

3482036 1 l

3484036 5 l

WHITE

3482004 1 l3484004 5 l

THINNER BASE and overprint varnish anti-UV3482040 1 l3484040 5 l

MATTING BASE

3482042 1 l

IMP.

TIF

LEX

28.

01.2

013



SCREEN PRINTING


*

SOLVENT INkSVINYLIQUE bRILLANTEGlossy air drying ink particularly intended for printing on self-adhesive substrates.


vINYlIQUE BrIllaNTEGlossy air drying ink particularly intended for printing on self-adhesive substrates.

¾¾ Appearance: high glossy¾¾ Average density: 1,12¾¾ Viscosity: 7 ± 1 Pa.s¾¾ Drying:

• ambient air 15 min. at 20°C • air jet dryer 1 min. at 50°C¾¾ Covering power: good¾¾ Coverage rate: 50 m²/l with a 120 -34 mesh¾¾ Weather resistance: good¾¾ Solvents:


• manual 2881, 2891, NS-81, NS-91, NS-99 and NS-100 • washer 2881, NS-81, NS-91, NS-99, and NS-100¾¾ Expiry date: refer to the label

The GLOSSY VINYL inks are printed on all varnished vinyl or polyester self-adhesive supports and also on polycarbonate sheets (macrolon®, lexan®).10% to 30 % matting base must be added, depending on the required finish.Not suitable on flexible PVC.

The GLOSSY VINYL inks complywith EN 71-3 standard.

sPEcIFIcaTIoNs


UsE

Ref. Packaging

sTaNDarD coloUrs

LEMON YELLOW OP3342002 1 l

GOLD YELLOW OP3342005 1 l

ORANGE OP

3342007 1 l

CHERRY RED OP

3342009 1 l

CARMINE RED OP

3342013 1 l

CYCLAMEN 8560

3342028 1 l


VIOLET 8570

3342032 1 l

LIGHT BLUE 8580

3342036 1 l

PRIMARY BLUE 85903342040 1 l

DEEP BLEU 8600

3342044 1 l

ROYAL BLUE 8605

3342046 1 l


DEEP GREEN OP

3342034 1 l

BROWN OP

3342042 1 l

BLACK 8660

3342068 1 l

COVERING WHITE85053342006 1 l

BasEs

ThIXo 4-CoLoURS yELLow 86703342081 1 l

ThIXo 4-CoLoURS mAgENTA 86803342082 1 l

ThIXo 4-CoLoURS CyAN 86903342083 1 l

ThIXo 4-CoLoURS BLACk 87003342085 1 l


Ref. Packaging

WHITE 8500

3342004 1 l

IMP.

TIF

LEX

28.

01.2

013


ThIXo 4-CoLoURS BASE 87103342096 1 l

THINNER BASE 48603342072 1 l


OVERPRINT VARNISHANTI-UV

3342076 1 l


SCREEN PRINTING


*

SOLVENT INkSVINYLIQUE mATEAir drying ink intended for printing on flexible (tarpaulins) or rigid PVC. Gives satin to matt finish printing with good resistance to blocking, alcohol and gasoline.


IMP.

TIF

LEX

28.0

1.20

13

vINYlIQUE MaTEAir drying ink intended for printing on flexible (tarpaulins) or rigid PVC. Gives satin to matt finish printing with good resistance to blocking, alcohol and gasoline.

¾¾ Appearance: satin to mat¾¾ Average density: 1.24¾¾ Viscosity: 12 ± 2 Pa.s¾¾ Drying:

• air 10 min. at 20°C¾¾ Covering power: very good¾¾ Coverage rate: 43 m²/l with a 100 - 40 mesh¾¾ Weather resistance: good¾¾ Solvents:

• thinner 4920 • retarder 4960 • adhesion 4903 or 9640 • gun XC 876 (minimum 70%) • brush 4905¾¾ Cleaning solvents:

• manual 2881, 2891, NS-81, NS-91, and NS-100 • washer 2881, NS-81, NS-91, and NS-100¾¾ Expiry date: refer to the label¾¾ Special property: thermoformable

The MAT VINYL inks are particularly suitable for printing on rigid or flexible PVC (plates, tubes, sheets, PVC coated nylon and polyester cloth).In addition they display excellent adherence on polycarbonate and polymethyl methacrylate.

The MAT VINYL inks comply with EN 71-3 standard.

sPEcIFIcaTIoNs


UsE

Ref. Packaging

sTaNDarD coloUrs

LEMON OP

3352002 1 l

GOLD YELLOW OP

3352004 1 l

ORANGE OP

3352007 1 l

CHERRY RED OP

3352008 1 l

PRIMARY RED 45003352021 1 l

CYCLAMEN

3352025 1 l


VIOLET

3352026 1 l

PRIMARY BLUE 44003352003 1 l

ROYAL BLUE 4401

3352006 1 l


DEEP GREEN OP

3352034 1 l

BROWN 4560

3352030 1 l

BLACK 4600

3352036 1 l

WHITE 4580

3352033 1 l

sPEcIal EFFEcT

SILVER3352040 1 l

GOLD Nº1 46223352042 1 l

Ref. Packaging

BasEs

GLOSSY THINNER BASE and overprint varnish anti-UV

3352057 1 l

MAT THINNER BASE and overprint varnish anti-UV

3352070 1 l

Ref. Packaging



SCREEN PRINTING


*

ETchINg rEsIsT Black XE880



Black bituminous ink formulated to print on printed circuits and aluminium. It resist to chemical etching baths and is removable with solvents. To obtain etching resistance, we recommend to print a homogeneous ink film (mesh 90 threads/cm) .Ink will be removed with solvent 4909. It dries at room temperature but a drying at 80°C increases the hardness of the surface and allows mechanical operations before etching (brushing).

IMP.

TIF

LEX

28.0

1.20

13

Specification

ETCHING RESIST BLACK XE880

DESCRIPTION REF. 1 kg

XE880 black 3512020

XE880Grinding fineness 8

Viscosity 13 ± 2 Pa.s

Solvents : - thinner - stripping

4909, 5 % maxnaphta / chloride solvents

Cleaning solvents : - manual - machine

2899 - 28912899

Expiry refer to the label

SCREEN PRINTING


*

SOLVENT INkSxF 260mixed air drying ink offering good adherence on various substrates: • metal, particularly aluminium and its alloys (curing essential) • PVC (drying in ambient air).


IMP.

TIF

LEX

28.0

1.20

13 -

Non

con

tract

ual c

olou

rs a

nd p

ictu

res

XF 260Mixed air drying ink offering good adherence on various substrates: • metal, particularly aluminium and its alloys (curing essential) • PVC (drying in ambient air).

¾¾ Appearance: satin¾¾ Average density: 1.10¾¾ Viscosity: 6 ± 3 Pa.s

• ambient air 20 min at 20°C • oven curing 15 min. at 130°C¾¾ Covering power: good¾¾ Coverage rate: 48 m²/kg with a 120 - 34 mesh¾¾ Special resistance: alcohol, petrol¾¾ Weather resistance: good¾¾ Light fastness: good¾¾ Solvents:


• manual 2881, 2891, NS-81, NS-91 and NS-100 • washer 2881, NS-81, NS-91 and NS-100¾¾ Expiry date: refer to the label

The XF 260 ink is mainly used for printing on anodized and sealed aluminium, and for printing on aluminium plates which will be stamped.For these 2 applications, curing 15 min at 130°C is essential.

The XF 260 inks comply with EN 71-3 standard.

sPEcIFIcaTIoNs


UsE

LEMON OP

3592010 1 l

CHERRY RED OP

3592008 1 l

MEDIUM BLUE OP

3592040 1 l

MEDIUM GREEN OP

3592055 1 l

BLACK OP

3594065 5 l

oP

Ref. Packaging

WHITE OP

3594005 5 l

sTaNDarD coloUrs

COVERING WHITE3594006 5 l

BasE & aDDITIvE

THINNER BASEAND OVERPRINT VARNISH3594090 5 l

Ref. Packaging

Ref. Packaging


tiflex catalogue 2013

Documents