the konica minolta banner printing guide v2.1
TRANSCRIPT
-
1 Created by Luke Bennett Konica Minolta Hotline Support (UK)
The Konica Minolta Banner Printing Guide
Emperon Controllers C203, C250, C252, C253, C300, C351, C352, C353, C450, C451
Fiery Controllers IC402, IC406, IC409
-
2 Created by Luke Bennett Konica Minolta Hotline Support (UK)
Things to check before proceeding First of all make sure that you are using the phase two drivers or above, to find this out go to your printers and faxes folder (Start/Settings/Printer and Faxes). Find the Konica Minolta driver icon, right click on it and go into properties. For Fiery drivers, click on the About tab For Emperon controllers click on printing preferences and then click on Version. If you dont have phase two drivers or higher, it will never work. Banner printing is not currently supported on Apple Macs. It will not work using a PCL driver it must be done using a Postscript driver. Banner printing is not supported on both the C550 and C650. When using the C203, C253, C353 or the C451 for Banner printing, it will not work with the booklet finisher (FS-608). Banner printing does not work from Publisher 2007.
-
3 Created by Luke Bennett Konica Minolta Hotline Support (UK)
Contents How to enable Banner mode Page 4 Emperon controllers Printing a JPEG File Page 5 Emperon Controllers Printing a PDF Page 11 Emperon Controllers Printing from Photoshop Page 15 Fiery Controller IC-402 (C351, C450) & IC406 (C300, C352) Printing a JPEG File Page 18 Fiery Controller IC-402 (C351, C450) & IC406 (C300, C352) Printing a PDF or from an application Page 23 Fiery Controller IC-409 (C353, C451) Printing a JPEG file Page 27 Fiery Controller IC-409 (C353, C451) Printing a PDF or from an application Page 32 Emperon Controllers Printing from Publisher 2002 Page 36
-
4 Created by Luke Bennett Konica Minolta Hotline Support (UK)
How to enable Banner mode First of all you need to press the Utility button on the panel of the machine. You will then see this on the touch screen, press Banner Printing
Then select ON and press ok
It will then display then screen shown below, you are now ready to print a banner. (Depending on the finisher option on your machine you may need to slide the finisher away to allow the paper to exit)
-
5 Created by Luke Bennett Konica Minolta Hotline Support (UK)
Emperon controllers Printing a JPEG File There is an easy way of printing a banner (XP operating system) using the Windows Picture and Fax Viewer (Photo Printing Wizard), which is shown below. Open the banner you wish to print in the Windows picture and fax viewer Click on the printer icon
This will bring up the printing wizard. Click next
-
6 Created by Luke Bennett Konica Minolta Hotline Support (UK)
This will then bring up the list of printers available, click on the arrow shown to show drop down menu.
Then select the printer you wish to use, in this case C450 PS (post script)
Then click on printing preferences
-
7 Created by Luke Bennett Konica Minolta Hotline Support (UK)
This will bring up the screen below; first thing to change is the original size
Then select custom size
-
8 Created by Luke Bennett Konica Minolta Hotline Support (UK)
This will bring up another screen shown below
You need to enter the following and click OK
-
9 Created by Luke Bennett Konica Minolta Hotline Support (UK)
It will then bring up the following message below, select yes.
It will then display the following options, click OK
-
10 Created by Luke Bennett Konica Minolta Hotline Support (UK)
Then click next
It will then show the screen below, its best to select Full page fax print as the Full-page photo print can sometimes crop the image. Check on the preview first before printing.
-
11 Created by Luke Bennett Konica Minolta Hotline Support (UK)
Then simply click on next and the job is sent to the printer.
Then your finished, click finish and it will close the wizard.
Emperon Controllers Printing a PDF
-
12 Created by Luke Bennett Konica Minolta Hotline Support (UK)
Open the file you wish to print as a banner. To start, go to file and print, it will show the screen below.
Chose your printer, for this I am using a C450 (post script)
Then click on properties
-
13 Created by Luke Bennett Konica Minolta Hotline Support (UK)
This will bring up the screen below; first thing to change is the original size
Then select custom size
-
14 Created by Luke Bennett Konica Minolta Hotline Support (UK)
This will bring up another screen shown below
You need to enter the following and click OK
It will then bring up the following message below, select yes.
-
15 Created by Luke Bennett Konica Minolta Hotline Support (UK)
It will then display the following options, click OK
As you will now see the preview of the image has changed and now shows the full page
Emperon Controllers Printing from Photoshop
-
16 Created by Luke Bennett Konica Minolta Hotline Support (UK)
For this I am using Photoshop Version 7. First of all go to file and print, it may come up with the error below but this is normal just press proceed.
Then chose your printer from the drop down menu, I am using the C450 (post script) Then click on properties
This will bring up the screen below; first thing to change is the original size
Then select custom size
-
17 Created by Luke Bennett Konica Minolta Hotline Support (UK)
This will bring up another screen shown below
You need to enter the following and click OK
It will then bring up the following message below, select yes.
-
18 Created by Luke Bennett Konica Minolta Hotline Support (UK)
It will then display the following options, click OK
Then simply press ok as shown below
Fiery Controller IC-402 (C351, C450) & IC406 (C300, C352) Printing a JPEG File
-
19 Created by Luke Bennett Konica Minolta Hotline Support (UK)
There is an easy way of printing a banner (XP operating system) using the Windows Picture and Fax Viewer (Photo Printing Wizard), which is shown below. Click on the printer icon
It will then open the printer wizard, click next
Select the image and click next
-
20 Created by Luke Bennett Konica Minolta Hotline Support (UK)
Then chose the relevant Fiery driver, for this I am using the IC402 driver Click on Printing Preferences
This will bring up the screen below
-
21 Created by Luke Bennett Konica Minolta Hotline Support (UK)
First thing to change is the document size, select as below
Then click on Custom
You then need to fill box out as shown below and press ok
-
22 Created by Luke Bennett Konica Minolta Hotline Support (UK)
You must then select the following, Bypass tray, Thick1 and Landscape and click ok
Then click next
You will then see the preview as shown below, click next
-
23 Created by Luke Bennett Konica Minolta Hotline Support (UK)
It will then show the below, click finish and your done
-
24 Created by Luke Bennett Konica Minolta Hotline Support (UK)
Fiery Controller IC-402 (C351, C450) & IC406 (C300, C352) Printing a PDF or from an application To start, go to file and print, it will show the screen below.
Chose your printer, for this I am using the IC402 driver
-
25 Created by Luke Bennett Konica Minolta Hotline Support (UK)
Then click on properties
This will bring up the screen below
-
26 Created by Luke Bennett Konica Minolta Hotline Support (UK)
First thing to change is the document size, select as below
Then click on Custom
You then need to fill box out as shown below and press ok
-
27 Created by Luke Bennett Konica Minolta Hotline Support (UK)
You must then select the following, Bypass tray, Thick1 and Landscape and click ok
Then click ok and your finished
-
28 Created by Luke Bennett Konica Minolta Hotline Support (UK)
Fiery Controller IC-409 (C203, C253, C353, C451) Printing a JPEG file There is an easy way of printing a banner (XP operating system) using the Windows Picture and Fax Viewer (Photo Printing Wizard), which is shown below. Click on the printer icon
It will then open the printer wizard, click next
-
29 Created by Luke Bennett Konica Minolta Hotline Support (UK)
Select the image and click next
Then chose the relevant Fiery driver, for this I am using the IC409 driver Click on Printing Preferences
-
30 Created by Luke Bennett Konica Minolta Hotline Support (UK)
This will bring up the screen below
First thing to change is the original size, select as below It may come up with a conflict screen as shown below; if so just press ok, this will auto change the paper tray to Bypass tray.
You then need to click onto custom
-
31 Created by Luke Bennett Konica Minolta Hotline Support (UK)
Change the sizes as below
As you will see it auto-changes Bypass tray for you so just change the following and click ok
Then click next
-
32 Created by Luke Bennett Konica Minolta Hotline Support (UK)
Check the preview is ok and press next
Then click finish and the wizard will close
-
33 Created by Luke Bennett Konica Minolta Hotline Support (UK)
Fiery Controller IC-409 (C353, C451) Printing a PDF or from an application To start, go to file and print, it will show the screen below.
Chose your printer, for this I am using the IC409 driver
-
34 Created by Luke Bennett Konica Minolta Hotline Support (UK)
Then click on properties
This will bring up the screen below
-
35 Created by Luke Bennett Konica Minolta Hotline Support (UK)
First thing to change is the document size, select as below
It may come up with a conflict screen as shown below; if so just press ok, this will auto change the paper tray to Bypass tray.
Then click on Custom
-
36 Created by Luke Bennett Konica Minolta Hotline Support (UK)
You then need to fill box out as shown below and press ok
You must then select the following and click ok
Then click ok and your finished
-
37 Created by Luke Bennett Konica Minolta Hotline Support (UK)
Emperon Controllers Printing from Publisher 2002 First of all go to page setup and under layout tab, setup as exactly as below.
Once completed click on Change Overlap, make sure its set to Print one sheet.
-
38 Created by Luke Bennett Konica Minolta Hotline Support (UK)
Then change to Printer & Paper tab and set as below. (I am using a C252)
Then click on Properties.
-
39 Created by Luke Bennett Konica Minolta Hotline Support (UK)
Then set as it is shown below. Must be the same or it will error.
For customer size set as shown below.
-
40 Created by Luke Bennett Konica Minolta Hotline Support (UK)
Then go to file/print, once it displays the screen below, chose Advanced Print Settings
Then untick Crop Marks as shown below, and click ok.
-
41 Created by Luke Bennett Konica Minolta Hotline Support (UK)
Then once set up simply click ok.