testreport_4.1 rets with rsu40 (umts2100) (cascaded)
DESCRIPTION
retTRANSCRIPT
4.
4.1 RETs with RSU40 (UMTS2100)
Configuration file:
Upload to FTP server Z:\Common\Testing\TMA test\TestReport\ConfigFile
NB version :
Figure 4.1.1: NB SW version
4.1.1 Device Management
4.1.1.1 Cascaded RETs Devices Scan
Figure 4.1.1.1.1 shows AISG Device Scan in left nevigation tree , right click to scan AISG device.
Figure 4.1.1.1.1: Right click to scan AISG device
Figure 4.1.1.1.2 shows the protocol choose AISG 2.0, and Rack No is 4, Rack 4 is the RSU40 rack that
the RET connected.
Figure 4.1.1.1.2: Choose the rack to scan
It will take a while to scan , figure 4.1.1.1.3 shows 3 RETs are scanned.
Figure 4.1.1.1.3: Scan result
4.1.1.2 Add Cascaded RETs AISG Device
In left nevigation tree ,choose AISG device. Right click to choose "Linkage Scan Records Configure".
Figure 4.1.1.2.1: Right click to add AISG device
Figure 4.1.1.2.2 shows RET which serial number is KACSD4533585(shown on the lable of the antenna)
is connected to RSU40-U216(4,1,1)-Ret-1.The same way to add the other RET devices to rack 2 and
rack 7 respectively, as shown in figure 4.1.1.2.3 and figure 4.1.1.2.4.
Figure 4.1.1.2.2: Add RET to rack 4
Figure 4.1.1.2.3: Add RET to rack 2
Figure 4.1.1.2.4: Add RET to rack 7
Figure 4.1.1.2.5 shows 3 RETs are added .
Figure 4.1.1.2.5: RETs are added
4.1.1.3 Delete Cascaded RETs AISG Devices
Figure 4.1.1.3.1 shows right click to delete the AISG device.
Figure 4.1.1.3.1: Delete AISG device
4.1.2 Application Layer Test
4.1.2.1 Alarm Management
Unplug AISG cable between the second cascaded RET and the third cascaded RET, “RET
communication is interrupted”are reported. The alarms show in EOMS rack status illustration as figure
4.1.2.1.1 shows.
Figure 4.1.2.1.1: Real-time alarm in rack status illustration
4.1.3 Configuration Management
4.1.3.1 Reset AISG Devices– OMCB
Figure 4.1.3.1.1 shows choose one RET and right click to reset.
Figure 4.1.3.1.1: Right click to reset
Figure 4.1.3.1.2: RET(KACSD4533585) reset successfully
Figure 4.1.3.1.3: RET(KACSD4532791) reset successfully
Figure 4.1.3.1.4: RET(KACSD4533581) reset successfully
4.1.3.2 Devices Self-Check
Figure 4.1.3.2.1 shows choose one RET and right click to reset. The same way to other two RETs.
Figure 4.1.3.2.1: Right click to self test
Those RET self test successfully , as the below 3 figures shows.
Figure 4.1.3.2.2: RET(KACSD4533585) self test successfully
Figure 4.1.3.2.3: RET(KACSD4532791) self test successfully
Figure 4.1.3.2.4: RET(KACSD4533581) self test successfully
4.1.3.3 Version Information Query
Figure 4.1.3.3.1 shows right click to choose “Query Version”.
Figure 4.1.3.3.1: Right click to query version
Figure 4.1.3.3.2 to 4.1.3.3.4 shows the version information.
Figure 4.1.3.3.2: RET(KACSD4533585) version information
Figure 4.1.3.3.3: RET(KACSD4532791) version information
Figure 4.1.3.3.4: RET(KACSD4533581) version information
4.1.3.4 RET Antennas Automatic Calibration
Figure 4.1.3.4.1 shows choose one RET and right click to auto adjust.
Figure 4.1.3.4.1: Right click to auto adjust
Figure 4.1.3.4.1: RET(KACSD4533585) reset successfully
Figure 4.1.3.4.3: RET(KACSD4532791) reset successfully
Figure 4.1.3.4.4: RET(KACSD4533581) reset successfully
4.1.3.5 SET RET Antennas Tilt
Figure 4.1.3.5.1 shows right click to set tilt.Take 5 degree for example.
Figure4.1.3.5.1: Right click to set tilt
Figure4.1.3.5.2: Set tilt (RET KACSD4533585)
Figure4.1.3.5.3: Set tilt successfully
Figure4.1.3.5.4: Set tilt (RET KACSD4532791)
Figure4.1.3.5.5: Set tilt successfully
Figure4.1.3.5.6: Set tilt (RET KACSD4533581)
Figure4.1.3.5.7: Set tilt successfully
4.1.3.6 Query RET Antennas Tilt
Figure 4.1.3.6.1 shows right click to query tilt.It was set to be 5 degree in item 4.1.3.5.
Figure4.1.3.6.1: Right click to query tilt
Figure 4.1.3.6.2 to figure 4.1.3.6.4 shows the value of tilt .
Figure4.1.3.6.2: Query tilt result (RET KACSD4533585)
Figure4.1.3.6.3: Query tilt result (RET KACSD4532791)
Figure4.1.3.6.4: Query tilt result (RET KACSD4533581)