t0172 warning: to avoid risk of electrical shock, be …

/ 16

Important to Know:1. If you are not familiar with state and local electrical codes, it is recommended that you consult with a qualified electrician.2. This fixture requires a 120 VAC, 60 Hz power source. 3. For general safety and to avoid any possible damage to the sensor, be sure the power is switched "off" before adjustment.Maximum Wattage: 25 WWorking Temperature Range: - 4°F ~ 113°F

ASSEMBLY AND INSTALLATION INSTRUCTIONS

NOTES: 1. Before installing, consult local electrical codes for wiring and grounding requirements. 2. READ AND SAVE THESE INSTRUCTIONS.

T0172

Features:1. Energy saving LED fixture.2. Motion sensor: turns light ON automatically when motion is detected and turns light OFF automatically when motion stops.3. Photocell keeps the light OFF during daylight hours.4. WIFI Camera operation with built-in camera, speaker & microphone, cloud connectivity, IOS & Android compatible. (please refer to page 5 to 16)

WARNING: TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFFPOWER BEFORE INSTALLING OR SERVICING THIS FIXTURE.

Note: Fixture can be wall mounted or eave mounted.

Wall Mounted Eave MountedRead notes section on page 3-4 for addictional information about mounting location of fixture.Light fixture and sensor should be mounted as shown above when installed (depending upon type of installation)

Before installing the light fixture under an eave, the sensor head must be rotated as shown in the next two steps for proper operation and to avoid the risk of electrical shock.

For eave mounted only:

Swing the sensor head towards the mounting bracket. Rotate the sensor head clockwise 180˚ so the controls face down.

ControlsMounting Bracket

Controls

Controls

Hardware Package (included):

Mounting Bracket Screw Fixture Mounting ScrewMounting Strap Wire Nut X3Mounting Screw X2#8/32X1/2 in

Mounting Screw X2#6/32 X1/2 in


150616

Wi� Security

/ 16

Installation Steps

1. The fixture mounting bracket is pre-assembled on the light fixture. Unscrew the fixture mounting screw in order to remove the mounting bracket.

2. Install the mounting strap to the outlet box with the stamped word “FRONT” facing away from the outlet box, using two mounting screws that best fit the outlet box. Mounting bracket should sit flush against wall surface when secured.(Choose one matching pair of suitable mounting screws from the 3 pairs provided)

3. Pull out the source wires from the outlet box. Make wire connections using wire nuts as follows: ---Connect the black wire from the fixture to the “hot” wire from the power source. (usually black) ---Connect the white wire from the fixture to the neutral wire from the power source. (usually white) ---Connect the grounding wire from the fixture to the grounding wire from the power source. (usually green / yellow insulation) Carefully tuck the wires back into the outlet box.

4. Place mounting bracket against the outlet box, insert the mounting bracket screw through the mounting bracket hole, thread mounting bracket screw into the center hole of the mounting strap. Tighten the mounting bracket screw securely. ▲ When mounting to a wall, the “UP” arrow must point upward. (See Fig. 1) ▲ When mounting to an eave, the “UP” arrow must point toward the building.

5. Attach the back plate of the light fixture to the mounting bracket, secure it with the fixture mounting screw.

6. With silicone caulking compound, caulk completely around where the mounting bracket meets the wall surface. CAUTION: Be sure to caulk completely where the mounting bracket meets the wall surface to prevent water from seeping into the outlet box.

SensorMounting Strap

Mounting Bracket

Outlet Box

Wire Nut

Back Plate

Mounting Screw

Light Head

-- Rotate the motion sensor so the controls face toward the ground.

Adjusting the Sensor Head:

Turn off the power at fuse or circuit box.

Turn on the power at fuse or circuit box.

Fig. 2

Fixture Mounting Screw

Mounting Bracket Screw

Fig. 1

FRONT

L (B

lack

)

N(W

hite

)

L (

Bla

ck)

N(W

hit

e)

SD

RESET WPS

5s 10Min

TIMELUX

150616

/ 16

Fig. 4

Fig. 3

Adjusting the Light Head: 1. Gently grasp the light heads and tilt them up or down, left or right to adjust the light coverage area. Keep the light heads at least 1˝ (25mm) away from the sensor.(See Fig. 4)

2. Keep the light heads 30˚ below horizontal to avoid water damage and electrical shock.

Adjusting the Motion Sensor Detection Zone: 1. Perform a “walk test”: walk in an arc across the front of the motion sensor.(See Fig.3)2. The light will come on and the red LED will flash indicating motion has been detected.3. Stop, wait for the light to turn off, and then begin walking again.4. Gently grasp the motion sensor and move it from side to side or up and down to adjust the detection zone.

Function and OperationNote: When power is first applied, the light will turn on. The sensor will take 30 seconds to warm up.

40 ft/110˚

1. ● “ ” MODE( daytime and nighttime operation) 1. Turn the knob clockwise to “ ”, the light turns on after expiration of the warm-up period, it stays on when motion is detected. When motion is no longer detected, it remains on for the predetermined shut-off delay time you set (5s~10 min), and then turns off automatically.

2. “ ” MODE(nighttime operation only) 1.Turn the knob counterclockwise to “ ” ,the light turns on after expiration of the warm-up period, it stays on when motion is detected. When motion is no longer detected, it remains on for the predetermined shut-off delay time you set (5s~10min), and then turns off automatically. 2. The light will turn off automatically at dawn.

Customization Options:Shut-off Delay● The shut-off delay is the length of time the light will stay at brightness after motion is detected.● You can set the shut-off delay by rotating the time delay knob arrow so it points to the desired time setting (from 5 seconds to 10 minutes). To increase the shut-off delay, turn the knob clockwise. To decrease the shut-off delay, turn the knob counterclockwise.

5s 10Min

TIMELUX

Fig. 5

20'8.0'

12.0'

40'

Notes:1. The sensitivity of the motion sensor will increase as the environmental temperature gets cooler. For best performance, gently clean the lens with a soft cloth every 1 or 2 months to assure maximum sensitivity.

2. For best performance, install fixture at least 8 feet above the ground. At such a height, the fixture will provide a detection distance of up to 40 feet at 77 degrees Fahrenheit. (See Fig.6)

3. The sensor detects movement across a detection range of 180 degrees. (See Fig.7)

Where you install your fixture is important:Be sure the light is mounted straight on the wall or eave; otherwise, the detection distance may be limited.

Fig. 6 Fig. 7180˚

150616

/ 16

Motion

Least sensitive

Motion

Most sensitiveSensor

4. The sensor will be more sensitive to motion across its detection path than motion directly towards it. (See Fig.8)

5. To reduce possible nuisances, do not mount the fixture near a heat source like an air conditioner, vent or furnace exhaust, or in a direction facing any reflective object or other nearby light source.

Fig. 8

Troubleshooting---The light does not come on at all:1. Make sure the wall switch and circuit breaker are on.2. Make sure the wiring is correct.3. Cover the sensor with dark color cloth to verify that the ambient light level is not too high.

---Light flashs:Cover PIR sensor len with black cloth / aluminum foil paper, if the light function is normal, then check for following.1. Excessive heat around the detection area.2. The PIR sensor is facing a tree or other obstacle.3. The PIR sensor is facing a fan or air conditioner.

---PIR sensor will not activate during daytime:1. Adjust the dusk level control to daytime(full clockwise)

Mounting Bracket Screw Fixture Mounting ScrewMounting Strap Wire Nut X3

Assembly Kit5327MM (1 SET)

A: 9-3/4"

B: 9-3/4"

C: 6-1/2"

The following parts are available for re-order if damaged or missing.

Mounting Screw X2#8/32X1/2 in



150616

5-YEAR LIMITED WARRANTY:All products are warranted to be free of defects in material and workmanship for five (5) years from date of purchase. This warranty is limited to the correction of any such defect, or the replacement of any such defective item(s), provided that: (a) we are properly notified and consent to return of the item(s) in question:(b) the item (s) is / are returned with proof of purchase date; and (c) it is found upon inspection by us that the item (s) is / are defectiveas noted above. This warranty dose not cover labor costs, consequential damages, nor dose it apply to any item(s) thathave been improperly installed, overloaded, altered, or otherwise abused by the customer, its agent(s) or emplyee(s).Finishes are specially excluded from the terms of this warranty since they are subject to environmental maintenance deemed beyond our control. Other than the described obligation, we assume no further liability with respect to the sale or use of our products.We make no warranty, express or implied, and disclaim any warranty of merchantability or fitnessfor a particular purpose.

A

B

C

/ 16

Software Setting

Brief Introduction of Wifi Security LightIntroduction of Wifi Security Light.1. The Wifi Security Light combines an LED security floodlight with an intergrated wireless camera device.2. The basic function of an wifi camera is to transmit remote video data through a computer network. Using the H.264 hardware compression technigue, the transmission speed of high quality video images across the network & internet can reach 25 frames per second real time.3. The transmission of wifi camera video data is based on TCP/IP protocol. The build-in web server supports Firefox and Chrome remote configuration and update firmware. You can use the Wifi Security Light to monitor areas in your home and office, or control the camera through network and manage images.

Product Features1. Powerful high- speed video protocol processor2. High-sensitivity 1/4˝ CMOS sensor3. Maximum 1.0 megapixel image resolution4. High-brightness LED illumination night vision5. Optimized H.264 video compression transmission6. Multi-level user management and password setting7. Build-in Web server that can be accessed by users through IE browser8. Wireless network compatibility (WI-FI/ 802.11/b/g/n)9. Dynamic DNS (DDNS), UPnP and internet (ADSL, broadband cable modem)10. Bi-directional audio monitoring11. Still image capture12. Multiple network protocols: HTTP/ TCP/ IP/ UDP/ STMP/ DDNS/ SNTP/ DHCP/ FTP13. Remote system update14. Maximum capacity of 32 GB SD memory card. (SD card sold separately)

Advanced Features1. Multiple transport protocols: Wifi Security Light supports many protocols, for example, TCP/ IP, SMTP and HTTP. When the Wifi Security Light alarm is triggered, it can send e-mail to you automatically.2. PIR sensor: Can automatically detect and trigger image recording and transmission.3. Wifi Security Light also provides dynamic DNS function.4. Advanced user management: Allows only authorized users to access the live video of Wifi Security Light.

Hardware Information of the Product1. External View of the Product: Indicator Status:■ System start-up indicator: The blue indicator will be on after it is powered on for 15 seconds, and it will enter the current mode indication after the indicator is normally on for 20 seconds.

■ AP mode: The blue indicator flashes with an interval of 1 second.

■ STATION mode: The blue indicator remains on.

■ Alarm: The red indicator flashes with an interval of 1 second.

■ WPS setting mode: The blue indicator flashes with an interval of 0.5 second.

■ Factory reset mode: The red indicator remains on and the blue indicator flashes with an interval of 0.3 second.

2. Operating Methods of Buttons:■ AP/RESET button: Press the button and hold for 3 seconds to enter the AP mode, hold for 8 seconds to enter the factory reset mode. (See Fig.9)

■ WPS button: Press and hold the button for 5 seconds to enter WPS. (See Fig.9)

150616

/ 16

Phone

Pc

Operating Methods of Buttons

A B

Wifi Security Light

Router Moden Internel

Phone Phone

PC

SD

RESET WPS

5s 10Min

TIMELUX

Ambient LightInduction Setting

SD Card

Time Setting

WPS

Reset

■ The connection between Wifi Security Light and other devices is through WIFI.

■ As shown in the above figure: Connection mode A is when a phone or PC is connected to the Wifi Security Light directly. Wifi Security Light must be set to the “factory reset” or AP mode to establish this type of connection.

■ The connection method: First you need to disconnect the current wireless network from your device ( pc or phone). Scan for the Wifi Security Light’s WIFI hotspot. This will be listed as “IPCAM-XXX” or similar. The default password is “null”, the function of this connection is to operate the built-in WEB server of the Wifi Security Light directly so as to set relevant parameters, including configuring Wifi Security Light to the router. When using the connection of Wifi Security Light and internet for first time, its WIFI should be connected to the router in this way.

■ Connection mode B is that the user has installed the Wifi Security Light, and the client software in the phone or PC can be used to view the monitoring screen in Wifi Security Light.

Quick Confiuration of Wifi Security Light1. Quick Configuration of Wifi Security Light■ When this product (Wifi Security Light) is used for the first time, it should be connected to a router with internet access. This process is called the quick configuration of Wifi Security Light. If the user wants to change the connecting router, set the Wifi Security Light in the “AP” mode and then conduct the quick configuration of Wifi Security Light.

2.1 The Method of Configuring Wifi Security Light through mobile device■ Search “Wifi Security” on IOS APP store or Android Google Play. Install the “Wifi Security” APP onto the device. It’s available for Apple and Android device.

■ Select the IPCAM_XXXXXX connection in the WIFI networking bar of the phone, leave the password field blank.■ Run the APP. (Take Android for example as below. IOS will be slightly different)■ Select “Click here to add camera”.

150616

Wi� Security

Fig. 9

■ Select “ Wifi Wizard add”.

■ Follow the prompt and select “Next”.

Wifi

/ 16

■ Input the WIFI password of the router and select “Next”.

150616

■ The password should be empty, tap on password held and select “Next” .

■ Choose router.

Configuration Method of WPS:Press the WPS button in the panel of Wifi Security Lightfor 5 seconds. The blue indicator will flash rapidly after entering into the WPS mode. Then press the WPS buttonon the router which you would like to connect to Wifi Security Light (refer to router manual for instructions on WPS mode operarion).

2.2 Usage of Phone Client Application Software■ Enable phone network function, install and run “Wifi Security” software.

■ Click “Click here to add camera”

■ Input the password of the camera default is blank and click “Save”. Wifi Security Light will restart. After restarting, the software can be connected with Wifi Security Light to see the screen. (you will need to reconnect to normal WIFI network)

■ Select different quick adding modes. NOTE: You can find the QR code on the light fixture.

■ Input username and password and Save

The password of Camera defaultis blank, if has been set, userneed input it.

Custom Camera Name

Input route password then click Next

IPCAM setting other guests access

The admin user has the highest administrative authority, can set the IPCAM password here.

/ 16

■ The camera has been successfully added if the following interface appears.

Explanations of menu in the main interface.

Camera Name

Camera OperationSetting

IDWIFI SignalSDStatus

■ Settings interface

■ User Setting interface

150616

AlarmSettings

Onlinestatus

EnterVideo

Camera MainInterface

Display the image and video files saved

Software Settings

LCAM-000839-CJCEM

/ 16

■ User Setting interface

■ Surveil the video interface

Audio Recording Intercom

StopTake Photo

Video Screen Settings

Video Format Settings

Record Video

150616

3.1 The Method of Configuring Wifi Security Light through PC■ Install the “Wifi Security” software in PC. (Please refer to the CD provided)

■ Select the IPCAM_XXXXXX connection in the WIFI networking bar of PC, the password is null.

■ Run the “Wifi Security” software.

■ Double-click the IP address in the following prompt box and input the user name “admin” and password “null” into the box.

■ Select “ RC Plug-in Mode” in the prompt box below.

IP Camera

/ 16

■ Select “ Device Management” in the prompt box below.

■ First select “wireless setting” in the following prompt box and select “search” on the right. Then the avialable nearby WIFI hot spots will appear. Select the user’s router and in the shared password box input the WIFI password. Click “set” and confirm. Wifi Security Light will count down and restart. After restarting, the client software can be connected with Wifi Security Light to see the screen.

■ Reconnect to normal wireless network.

■ Operation Guide Live Video When logging into the system for the first time, IE will prompt “Install the plug-in from Player ActiveX” automatically. Video can be seen after installing it according to the prompts in the page.

■ The picture is the homepage after logging into the camera, and the menu page of live video. The serial numbers in the picture are explained as follows:

150616

/ 16

Serial No:

Name Explanation

Menu barThere are the live video and device management swift menus at the topleft corner of the main interface

1

0

Switch of multichannel device

The live video of the camera can view 9 channelsat the same time at most

2Current

device status

The connection, video, audio, talk and recording status of the current device.

3Login

device status

Recording, alarm and storage. It will popup more status information whenthe mouse moves to it.

4User

information The username of the current login user:

5

Switch of multiple device

(2409M)

Switch among one device, four devices and nine devices.

6

Audio and video options as well as record and

snapshot

Adjust the audio and video of the camera, live video playing and basic attribute setting of the camera

1. Control the playing or stop of camera video2. Control the open and close of camera audio

3. Start dialogue

4. Local recording. The time can select 10,

5. Device recording

6. When snapshoting, the camera has the options of continuous capture modes of 3, 4, 5 and 6 photos

7

1. Adjust the camera resolution (4 options)

2. Adjust the camera buffer time

3. Adjust the camera frequency (50HZ, 60HZ)

4. Select camera mirror and flip5. Set the brightness of camera

6. Set the sharpness of camera

7. Set the contrast of camera

8. set the saturation of camera

9. Set the white balance

10. Restore defaults

7. Setting of camera parameters

Device parameter setting Camera parameter setting

150616

■ Device Management Device Status

Device Log which records the last 100 device logs of the camera.

■ Basic setting

Alias Setting

User Setting

■ User Settings: It can set eight users at most as admistors or visitors. It can also set the permissions on their video, snapshot, device record, audio,talk and control.

■ Basic status of the device

2nd,August.2014 Saturday










60HZ

/ 16 150616

■ Multiple device setting

It can set eight devices at most and can connect eightmultiple devices at the same time.

Network SettingsIf the router connected by the device has the function of DHCP server, you can check “Obtain IP from DHCP Server”. Otherwise, fill in the network paraments as shown in the figure below manually.Http Port: In most cases, you can set it as 80. However, if your internet service provider stops this port, you may have to set it as other optional values (from 0 to 65535, do not set it as the same value as gateway), for example,8080,85,etc.

IP Settings

Wireless Settings

PPPoE Settings

DDNS Service■ DDNS Service: The system supports the protocols provided by DynDNS.org,3322.org, Oray.net,9299.org, No-ip.com and myfoscan.org in DDNS service.

■ Username and password: The username and password you used when applying for domain name.

■ DDNS Domain: The domain you applied for the device.

■ Setting requirements of username and password, the username, being a required filed, can not be“admin”. For the group of adminstrators, the password should have six characters at least and include figures and letters.

■ Setting allows access:

Http Port Settings

/ 16 150616

■ Configure the e-mail sent and received. When there is an alarm or the IP address of the device changes, the receiver will receive the e-mail of the sender.

■ Note: Send alarm capture through e-mail. Check Alarm Settings -> Mail Notification after Alarm.

■ Sender: The mailbox to send e-mails.

■ Receiver: The mailbox to receivecaptures and IP address. Four receiving mailboxes can be set at most.

■ SMTP Server: The SMTP server to send mails.

■ Need Authentication: If the sender needs to be authenticated, please fill in the correct username and password.

■ Mail Test: Fill in the above mail parameters and click “Set” for test. You can see the test result in a pop-up window and receive a test mail in the receiving mail box.

■ Mail Notify Internet IP Address: If this item is checked, when internet IP or port is set, please make sure that the port is mapped in router correctly through the virtual server function of UPNP or router. (take an example for the contents sent in the mail, IPCAM’s url is http://119.123.207.96:9002)

■ Alarm Settings: Set enable alarm schedule, three alarm methods can be enabled, namely, motion detect, trigger detec and sound detec, it can also set the sensitivity.

Alarm Action Settings:

■ Alarm Action Settings: The actions enabled after alarm.

Record Settings

The setting page of mailbox

Alarm Settings

/ 16 150616

Record Settings and Record File Management

SD memory Card Record File Management. Search thefile recorded, download it to local computer, and then youcan watch it directly. (The player is VLC. Downloadthe lastest version of VLC media player fromhttp://www.videolan.org)

Security Settings

2nd August 2014 Sat

2nd August 2014 Sat

2nd August 2014 Sat

2nd August 2014 Sat

Dictionary attack settings

Record Settings, Edit Schedule

3.2 Usage of PC Client Application Software■ Install and run the “ Wifi Security” software. Enter the username and password.

■ Set the date and time of camera access and the IP access permission.

■ Tools: Backup Settings, Restore Settings, Upgrade System Firmware and Upgrade Embedded Htmls.

Tools

/ 16 150616

Alarm record bar

Camera information bar

Language selection

■ Management window

Camera information added

Select add camera here

Select add camera here

Advance Setting to WEB

■ Control window

■ P2P Settings■ Main control interface

FAQ Changing the connected router

There are two methods to change the connected router:1. First set the Wifi Security Light into “AP” mode and implement Wifi Security Light quick configuration.2. Use the administrator rights to find the wireless network setting menu in the client software and modify it.

If I forgot my password:Press and hold the RESET button in the Wifi Security Light panel for 10 seconds while the device is on. And all parameters will restore to default values (factory values). The factory user name is admin and password is null.

If you face any problem, please check your network firstlyCheck the status indicator of network devices (concentrator, switch and network card). If they are abnormal, check your networking.

IP Address ErrorCheck the IP address of the device to see if it is in the same subnet segment with your local computer: open My Computer > Control Panel > Network & Dial-up Connection > Local Network > Internet Protocol (TCP/IP), examine subnet mask, IP address and gateway. When setting the IP address of the device manually, please make sure that they are in the same subnet. Otherwise, it can not visit the device normally.

/ 16

FCC Certification RequirementsCaution:Any changes or modifications in construction of this device which are not expressly approved by the partyresponsible for compliance could void the user’s authority to operate the equipment.This device complies with part 1S of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, includinginterference that may cause undesired operation.The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to thisequipment. Such modifications could void the user’s authority to operate the equipment.This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 1Sof the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installedand used in accordance with the instructions, may cause harmful interference to radio communications. However,there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmfulinterference to radio or television reception, which can be determined by turning the equipment off and on, the useris encouraged to try to correct the interference by one or more of the following measures:- Reorient or relocate the receiving antenna.- Increase the separation between the equipment and receiver.- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.- Consult the dealer or an experienced radio/ TV technician for help.

The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20cm fromall persons.

150616

Network ProblemNetwork Connection ProblemMke sure that your HTTP server software is configured correctly and runs well. If you have used any firewall software,make sure that the 80 port can be accessed externally. If you are using shared ADSL router, please ensure that the suitable port forwarding is set. (Please refer to the users’ manual of your router). If these do not any problem, it may bebecause your internet service provider blocks the 80 port – to prevent worm virus, like Code Red. In this case, you may have to modify your port (for example, 8080).

Network Bandwidth ProblemThe frame rate of images depends on the following factors: 1. network bandwidth; 2. performance of computer and network environment; 3. the quantity of users logging in the device (too much user acess will lower the frame rate of images); 4. using a switch or a concentrator (use a switch rather than a concentrator if there are many devices). The quality of images transmitted will be better if the network bandwidth is broader.

No Image Displayed in ActiveX Plug-in Video images are received and displayed to users through ActiveX plug-in. If the installation is not correct, the images may not be displayed. To solve this problem, there are two methods:1) Install “IP Camera Tool”, then the ActiveX plug-in will be installed at the same time (recommended).2) Download and install Active X-plug-in and modify the security settings of IE browser when visiting the device for the first time.Set three options in “ActiveX widget and plug-in” “Custom Level” “Security” “Internet Options” “Tools” “IE” browser as “Enable”:Enable: download unsigned ActiveX widgetEnable: conduct initialization and script running for the ActiveX widgets which do not signed as safeEnable: run ActiveX widget and plug-inBrowser Faces a ProblemIt is recommended to use FireFox browser tologin the device.The download link of FireFox browser:Http://www.firefox.com.

t0172 warning: to avoid risk of electrical shock, be …

Documents