swrsc-sd3611

Upload: anonymous-73geyyetl

Post on 24-Feb-2018

215 views

Category:

Documents


0 download

TRANSCRIPT

  • 7/25/2019 swrsc-sd3611

    1/2

    May, 2010 Page 1 of 2

    Carrier Software SystemsSyracuse, NY, USA

    [email protected]

    Carrier Electronic Catalog

    AHUBuilder v6.11

    Release Sheet

    AHU Builder v6.11 replaces v6.03.

    UPDATE DESCRIPTION

    AHUBuilder v6.11 introduces the updated 39M product. Highlights of this product update include:A reduction in unit height of 2 when using the standard 6 baserail.Indoor units now have 4, 6, 8 and 10 baserail height options.Inswinging doors on positive pressure sections.FMB and ANG sections now have identical filter arrangements.

    New shipping split design simplifies installation.New thru panel handle design.New drain pan design.New outdoor baserail design simplifies installation.New outdoor coil connection housing design simplifies installation.Additional 410a condensing units added to the AHUBuilder library.Updated accessory list subgroups are easier to navigate.

    New shipping rules to prevent oversize shipping sections where possible.Shipping segment weights and dimensions displayed in the submittal report.

    A DX-crossplot diagram is now available in the Performance reports.In addition, the following problems were corrected:

    The entering air and leaving air dew points were inverted on the Humidifier Performance report.The mixed-air calculator minimum entering temperature has been reduced to allow calculation in winter conditionsIn addition, when using total airflow for the calculation, the return air automatically adjusts for the OA input, justlike it does when using the percent method for the calculation.Fixed an error running electric heater calculations for 39M unit sizes 72 and above.Limit system airflow to the minimum allowable airflow on the electric heater.

    INSTALLATION PROCEDURES

    I nstallation via I nternet Download

    To perform a full program install, please use the following procedure:Download the ecat-sd3611.exefile from the Internet site and save it in a folder on your hard disk.Run Windows Explorer and double-click on the ecat-sd3611.exefile. This launches the program installer.Follow the installation instructions that appear on your screen.

    Note that X Builder Framework and AutoDesk Volo View Express must also be installed for AH UBuilder tofunction correctly. Both can be downloaded from the internet site.

    Running the Program:

    Carrier Electronic Catalog can be used to launch AHUBuilder. To start Electronic Catalog:From the Windows desktop press Start, choose Programs and then choose Carrier E-CAT and E20-II programs.In the Carrier E-CAT and E20-II Programs group choose the Carrier Electronic Catalog item. From Electronic

    Catalog you can create new or edit existing tags via the Project tab, or you can directly launch the program via thePrograms tab.

    AHUBuilder can also be launched from the Start Menu:From the Windows desktop press Start, choose Programs and then choose Carrier E-CAT and E20-II programs.Then choose Individual Product Builders.Finally click on theAHUBuilder v6.11 item.

  • 7/25/2019 swrsc-sd3611

    2/2

    May, 2010 Page 2 of 2

    Carrier Software SystemsSyracuse, NY, USA

    [email protected]

    Carrier Electronic Catalog

    AHUBuilder v6.11

    Release Sheet

    INSTALLATION PROCEDURES (continued)

    Minimum Computer Requirements:

    Hard Disk Space: 30 megabytes (for program and submittal drawing managers)Random Access Memory: At least 32 megabytesDisplay Monitor: At least VGA with 600x800 resolution and 256 colors.Operating System: Windows 98, ME, 2000, XP, Vista or Windows NT (with service pack 4 or later).E-CAT/E20-II Configuration Services v2.1Autodesk Volo View Express

    Note: X-Builder Framework and Autodesk Volo View Express programs should be installed prior to installing andrunning AHU Builder. Both can be downloaded from the internet site. Volo View Express (copyright Autodesk,Inc.) is freely distributed by Autodesk, Inc., as its drawing viewer. Any redistribution of Volo View Express must

    be in compliance with the Software License Agreement which is displayed during the Volo View Expressinstallation.

    PREVIOUS VERSION INFORMATION1. Converting Tags From Existing Projects. Project data fromAHUBuilder 6.00 through 6.03 can be converted for

    use in v6.11 as follows:Start AHUBuilder v6.11 directly, either via Start > Programs > Carrier E-CAT and E20-II Programs >Individual Product Builders, or via the Programs tab in Electronic Catalog.Open the desired project containing AHUBuilder tags. Initially no tags will be visible in AHUBuilder.Choose the "Convert from Prior Version" option on the File Menu. Tags will be converted and will thenappear in AHUBuilder. A summary report of required changes and/or errors will be displayed. These tagswill also appear in the Electronic Catalog project tree once saved.

    Note that this procedure must be repeated for each existing project you wish to use in AHUBuilder v6.11.

    2. Converting Project Archives. Project Archives from AHUBuilder 6.00 through 6.03 must be retrieved usingAHUBuilder 6.0x or Carrier Electronic Catalog before they can be converted to AHUBuilder version 6.11.

    3. Uninstalling AHUBuilder v6.03. AHUBuilder v6.11 will not replace v6.03 automatically. AHUBuilder v6.03must be uninstalled separately by using the following procedure:

    Do not uninstall v6.03 until you finish converting v6.03 data to v6.11 format (see item #1 above).Then, start the Carrier Electronic Catalog.Click on the Programs tab and highlight the AHUBuilder 6.0 item on the tree.Click the Remove Program button to uninstall AHUBuilder 6.03.

    SPECIAL NOTES

    1. XBuilder The latest version of X Builder Framework should be installed before installing AHU Builder.

    2. AutoDesk VoloView Expressmust be installed in order to view DXF Certified and Template drawings in theprogram.

    3. Windows 2000 Users. When running the program on a computer using Windows 2000, on which Adobe AcrobaReader has not been installed, the program will be unable to display AIRManager wiring diagrams but may notissue any error message. The solution to this problem is to download the latest version of Adobe Acrobat Readerfromwww.adobe.com/products/acrobatand then install it.

    http://www.adobe.com/products/acrobathttp://www.adobe.com/products/acrobathttp://www.adobe.com/products/acrobathttp://www.adobe.com/products/acrobat