switches and sensors catalogue

Switches and Sensors Catalogue

Oil Pressure Water Temperature Coolant Temperature

Thermo Fan Stop Light Reverse Light

This section has been included to assist with the identifi cation of Tridons extensive range of engine oil pressure senders and sensors. Photographs and specifi cation tables are shown for each Tridon part number. Each specifi cation table contains spanner size, thread size, plug type, circuit diagram and pressure rating. The Tridon oil pressure senders and sensors range has been developed to operate within original equipment manufacturers specifi cations. As oil pressure values vary always refer to the vehicle application list to ensure correct part number selection.

Oil Pressure Senders And Sensors

Function

The engine oil pressure sender/sensor is used to measure the integrity of

the engine lubrication system. Normally located in the engine block, the

oil pressure sender responds to changes in engine oil pressure modifying

the signal from oil pressure instrumentation. This modifi ed signal is used to

determine the engine oil pressure via oil pressure light or gauge.

There are 3 main types of engine oil pressure senders and sensors;

spring controlled diaphragm, thermal transducer and piezo-resistor.

Spring Controlled Diaphragm Contains a spring loaded diaphragm designed to open a set of

contacts as pressure increases.

For operation of oil pressure lights (only ON or OFF switch position).

Thermal Transducer Contains a diaphragm designed to close a set of contacts attached to a

bimetal alloy leaf. The bimetal leaf defl ects with changes in oil pressure.

A corresponding bimetal leaf in the oil pressure gauge performs the

same operation, registering the appropriate pressure reading.

For operation of oil pressure gauges.

Piezo-Resistor Contains a semiconductor crystal, with special resistance

properties. Changes in these properties occur when pressure is

applied; the changes are then processed to operate an oil display.

For operation of electronic oil pressure gauges.

Testing and Replacement

The engine oil pressure sender/sensor is an integral component in a vehicle

engine warning system; a faulty engine oil pressure sender/sensor may

provide incorrect warning signals leading to potential engine damage.

Engine oil pressure senders/sensors should be inspected regularly, the

sender/sensor should be checked for any visible signs of contaminant.

Note the engine oil itself, particularly old oil or incorrect oil levels may cause

a sender/sensor to malfunction.

When an engine oil pressure sender/sensor malfunction or fault is

suspected, the engine oil pressure sender/sensor should be checked and

replaced by a trained professional.

Oil Pressure Sender/Sensor Testing Procedure

1. Check the oil pressure sender/sensor for visible faults or oil leaks.

2. Check correct oil pressure sender/sensor operation;

Oil Pressure Senders and Sensors

68

Spring Controlled Diaphragm (oil pressure lights)Measure continuity across the oil pressure sender/sensor contacts;

Using an Ohmmeter, remove the terminal or plug, connect the Ohmmeter between the sender/sensor terminal and the vehicle

earth (ground).

With the engine OFF, the reading given should be zero (0) or show a closed circuit.

Start the engine, as the oil pressure rises the reading given should become infi nite or open circuit.

Thermal Transducer (oil pressure gauges)Test the operation of the oil pressure gauge circuit;

Remove the wiring plug or terminal, connect a potentiometer between terminal and vehicle earth (ground).

With the ignition turned on, test the operation of the oil gauge starting the potentiometer at a high resistance (around 500) then slowly

reduce the resistance to 0. The gauge should operate from low

pressure to high or a maximum pressure. (Resistance values

will vary between make and models, test procedure should be

used as a guide only).

Piezo-Resistor (electronic oil pressure displays)For testing procedures for a Piezo-resistor type sensor refer to

Thermal transducer type tests.

3. Replace the sender/sensor if readings are not as shown above.

4. Other oil pressure circuit tests include; Gauge and light tests with a potentiometer. Wiring tests, open and short circuits. Available voltage (check fuses) - voltage stabilizer or voltage

regulator normally located in the instrument cluster.

The Tridon engine oil pressure sender/sensor range has been developed

to operate with OEM specifi cations. As sender/sensor pressures values

may vary, always refer to the Tridon Vehicle Application list to ensure

correct part number selection.

Engine Oil Pressure Sender Circuit

)GNITION3WITCH /IL0RESSURE3ENDER

&USE /IL0RESSURE,IGHT

Engine Oil Pressure Sensor Circuit

)GNITION3WITCH

/IL0RESSURE3ENSOR

&USE/IL0RESSURE'AUGE

,OW (IGH

69

* Test procedure values will vary between make and models and should be used a guide only.

Identifi cation Guide

14

1/8 GAS

6.3

14

1/8 GAS

6.3

14

1/8 GAS

6.3

14

1/8 GAS

6.3

14

1/8 GAS

6.3

24

1/8 GAS

6.3

Bar0.40

24

1/8 GAS

6.3

Bar0.30

24

1/8 GAS

6.3

Bar0.40

27

1/8 PT

Bar0.30

24

1/8 GAS

Bar0.20

24

1/4-18 NPT

8-32 UNC

Bar0.30

24

1/8 GAS

M4

Bar0.30


70 Note: To ensure correct product selection please check illustrations and specifi cations as values may differ.

TPS001

TPS004

TPS007

TPS011

TPS002

TPS005

TPS008

TPS012

TPS003

TPS006

TPS010

TPS013

24

1/8 GAS

4

Bar0.30

24

1/8 GAS

4

Bar0.40

27

1/8 GAS

4

Bar0.30

24

1/8 GAS

Bar0.20

21

M14 x 1.5

6.3

Bar0.30

21

M14 x 1.5

6.3

Bar0.30

24

M10 x 1

6.3

Bar0.30

24

M10 x 1

6.3

Bar0.30

23

M18 x 1.5

6.3

Bar0.70

21

M16 x 1.5

6.3

Bar0.60

24

M14 x 1.5

6.3

Bar0.30

24

M12 x 1.5

6.3

Bar0.15

71

Oil

Pre

ssu

re S

end

ers

& S

enso

rs

Note: To ensure correct product selection please check illustrations and specifi cations as values may differ.

TPS014

TPS017

TPS020

TPS023

TPS015

TPS018

TPS021

Note: Replaces original brown part

TPS024

TPS016

TPS019

TPS022

TPS025

Note: Replaces original red part


24

M12 x 1.5

6.3

Bar0.35

24

1/8-27 NPT

8-32 UNC

Bar0.50

24

1/4-18 NPT

6.3

Bar0.40

24

M10 x 1

6.3

Bar1.80

24

M10 x 1

6.3

Bar1.40

24

1/8-27 NPT

6.3

Bar0.50

24

1/8-27 NPT

6.3

Bar0.30

24

M14 x 1.5

Bar0.50

24

M14 x 1.5

Bar0.50

24

M12 x 1.5

Bar0.30

24

M10 x 1

6.3

Bar0.30

24

1/8-27 NPT

Bar0.35



TPS026

Note: Replaces original brown and blue parts

TPS030

Note: Replaces original white part

TPS033

TPS039

TPS027

TPS031

Note: Replaces original black part

TPS034

TPS040

TPS029

TPS032

TPS038

TPS041

24

M10 x 1

6.3

Bar0.90

21

M14 x 1.5

Bar0.30

24

M12 x 1.5

M4

Bar0.40

24

M10 x 1

6.3

Bar0.30

24

M10 x 1

6.3

Bar2.50

21

M16 x 1.5

Bar0.50

24

M10 x 1

6.3

Bar0.50

24

1/8 GAS

Bar0.40

21

M16 x 1.5

Bar0.50

24

M10 x 1

Bar0.70

24

M10 x 1

Bar0.25

24

M10 x 1

Bar0.90

73

Oil

Pre

ssu

re S

end

ers

& S

enso

rs


TPS042

Note: Replaces original brown and grey parts

TPS045

Note: Replaces original light blue part

TPS048

TPS051


TPS043

TPS046

TPS049

TPS052

Note: Replaces original dark blue part

TPS044

TPS047

TPS050

TPS053

Note: Replaces original grey part


24

M10 x 1

Bar1.40

24

M10 x 1

Bar1.80

24

M10 x 1

Bar0.50

24

1/4-18 NPT

Bar0.40

24

3/8 NPT

Bar0.50

21

M14 x 1.5

Bar0.50

24

1/4-18 NPT

6.3

Bar0.40

14

1/8 GAS

27

1/4-18 NPT

27

1/4-18 NPT

4.7

Bar0.40

27

1/4-18 NPT

14

1/8 GAS

Bar0.60



TPS054


TPS057

TPS061

TPS065

TPS055


TPS058

TPS063

TPS066

TPS056

Note: Replaces original green part

TPS059

TPS064

TPS067

Circuit TypeN/C = Normally Closed

N/O = Normally Open

7575

Part No. Spanner Thread Circuit Type Pressure Notes

TPS001 14 1/8 GAS

TPS002 14 1/8 GAS

TPS003 14 1/8 GAS

TPS004 14 1/8 GAS

TPS005 14 1/8 GAS

TPS006 24 1/8 GAS N/C 0.40

TPS007 24 1/8 GAS N/C 0.30

TPS008 24 1/8 GAS N/C 0.40

TPS010 27 1/8 PT N/C 0.20

TPS011 24 1/8 GAS N/C 0.30

TPS012 24 1/4 - 18 NPT N/C 0.30

TPS013 24 1/8 GAS N/C 0.30

TPS014 24 1/8 GAS N/C 0.30

TPS015 24 1/8 GAS N/C 0.40

TPS016 27 1/8 GAS N/C 0.30

TPS017 24 1/8 GAS N/C 0.20

TPS018 21 M14 x 1.5 N/C 0.30

TPS019 21 M14 x 1.5 N/C 0.30

TPS020 24 M10 x 1 N/C 0.30

TPS021 24 M10 x 1 N/C 0.30 Replaces original brown part

TPS022 23 M18 x 1.5 N/C 0.70

TPS023 21 M16 x 1.5 N/C 0.60

TPS024 24 M14 x 1.5 N/C 0.30

TPS025 24 M12 x 1.5 N/C 0.15 Replaces original red part

TPS026 24 M12 x 1.5 N/C 0.35 Replaces original brown and blue parts

TPS027 24 1/8 - 27 NPT N/C 0.50

TPS029 24 1/4 - 18 NPT N/C 0.40

TPS030 24 M10 x 1 N/O 1.80 Replaces original white part

TPS031 24 M10 x 1 N/O 1.40 Replaces original black part

TPS032 24 1/8 - 27NPT N/C 0.50

TPS033 24 1/8 - 27 NPT N/C 0.30

TPS034 24 M14 x 1.5 N/C 0.50

TPS038 24 M14 x 1.5 N/C 0.50

TPS039 24 M12 x 1.5 N/C 0.30

TPS040 24 M10 x 1 N/O 0.30

TPS041 24 1/8 - 27 NPT N/C 0.35

TPS042 24 M10 x 1 N/O 0.90 Replaces original brown and grey parts

TPS043 21 M14 x 1.5 N/C 0.30

TPS044 24 M12 x 1.5 N/C 0.40

TPS045 24 M10 x 1 N/C 0.30 Replaces original light blue part

TPS046 24 M10 x 1 N/O 2.50

TPS047 21 M16 x 1.5 N/C 0.50

TPS048 24 M10 x 1 N/C 0.50

TPS049 24 1/8 GAS N/C 0.40

TPS050 21 M16 x 1.5 N/C 0.50

TPS051 24 M10 x 1 N/O 0.70 Replaces original brown part

TPS052 24 M10 x 1 N/C 0.25 Replaces original dark blue part

TPS053 24 M10 x 1 N/O 0.90 Replaces original grey part

TPS054 24 M10 x 1 N/O 1.40 Replaces original black part

TPS055 24 M10 x 1 N/O 1.80 Replaces original white part

TPS056 24 M10 x 1 N/O 0.50 Replaces original green part

TPS057 24 1/4 - 18 NPT N/C 0.40

TPS058 24 3/8 NPT N/C 0.50

TPS059 21 M14 x 1.5 N/C 0.50

TPS061 24 1/4 - 18 NPT N/C 0.40

TPS063 14 1/8 GAS

TPS064 27 1/4 - 18 NPT

TPS065 27 1/4 - 18 NPT N/O 0.40

TPS066 27 1/4 - 18 NPT

TPS067 14 1/8 Gas 0.60

Quick Reference Guide

75

Oil

Pre

ssu

re S

end

ers

& S

enso

rs

This section has been included to assist with the identifi cation of Tridons extensive range of water temperature senders. Photographs and specifi cation tables are shown for each Tridon part number. Each specifi cation table contains spanner size, thread size, plug type and circuit diagram. The Tridon water temperature sender range has been developed to operate within original equipment manufacturers specifi cations. As Tridon water temperature sender circuits vary always refer to the Tridon vehicle application list to ensure correct part number selection.

Water Temperature Senders

Function

The water temperature sender is used to measure the integrity of the engine

cooling system. Located on the engine side of the thermostat in the cooling

system, the water temperature sender responds to changes in engine

coolant temperature modifying the signal from engine temperature

instrumentation. This modifi ed signal is used to determine the engine

coolant temperature via water temperature light or gauge.

The most common type of water temperature sender is a thermistor type

sender unit, containing semiconductor materials which respond to coolant

temperature changes. Most commonly used are thermistors with a negative

temperature coeffi cient (NTC), which respond with decreasing resistance

as the temperature increases. This decrease in resistance creates a higher

current fl ow through the bimetal leaf located inside the temperature gauge,

indicating the appropriate engine temperature reading.


The water temperature sender is an integral component in a vehicle

engine warning system; a faulty water temperature sender may provide

incorrect warning signals leading to possible engine overheating and

potential engine damage.

Water temperature senders should be inspected at regular service

intervals, the sender should be checked for any visible signs of

contaminant and conductivity. Note the coolant itself, particularly

old coolant, incorrect coolant levels or mixture may cause the sender

to malfunction.

When a water temperature sender malfunction or fault is suspected, the

sender should be checked and replaced by a trained professional.

77

Water Temperature Sender Testing Procedures

1. Remove the water temperature sender from the vehicle.

2. Check the water temperature sender for visible contaminant, conductivity or leaks.

3. Check correct water temperature sender operation; Suspend the sender in a beaker fi lled with water so that the

bulb is covered. Using an Ohmmeter, measure the resistance across the

terminals (or terminal to the body of the sender). Heat the water until a simulated engine operating temperature is

achieved (80C - 90C). The sender is designed to respond to the

change in temperature (as the water temperature increases the

sender resistance will decrease or has a negative temperature

coeffi cient NTC). At low temperatures the resistance values may be several thousand

ohms () and reduce to as low as a few hundred ohms () at normal

engine operating temperatures.

4. Other water temperature circuit tests include; Gauge and light tests with a potentiometer. Wiring tests, open and short circuits. Available voltage (check fuses) - voltage stabilizer or voltage regulator,

normally located in the instrument cluster.

The Tridon engine water temperature sender range has been developed

to operate with OEM specifi cations. As sender values may vary, always

refer to the Tridon Vehicle Application list to ensure correct part number

selection.

Typical Temperature Gauge Circuit

.4#

&ROM)GNITION3WITCH

6OLTAGE3TABILISER

4EMP3ENDER

4EMP'AUGE

#OLD (OT

78

Water Temperature Senders


12

1/8 GAS

6.3

17

M16 x 1.5

4

12

1/8 GAS

4

12

1/8 GAS

6.3

17

M16 x 1.5

6.3

17

M16 x 1.5

6.3

17

M16 x 1.5

12

1/8 GAS

17

3/8-18 NPT

10-32 UNF

12

3/8 GAS

4

17

M16 x 1.5

6.3

12

M8 x 0.75

4

79

Wat

er T

emp

erat

ure

Sen

der

s


TTS001 TTS002 TTS003


TTS007

Note: Replaces original black and grey parts

TTS008

Note: Replaces original black and grey parts

TTS010


17

M16x1.5

4

17

M16x1.5

6.3 6.3

17

M16x1.5

6.3

13

M12 x 1.25

6.3

13

1/8-27 NPT

4.7

13

1/8-27 NPT

6.3

19

M14x1.5

6.3

19

5/8-18UNF

6.3

17

M16x1.5

6.3

19

5/8-18UNF

6.3

13

M8 x 0.75

4

17

M16 x 1.5

4




TTS021 TTS023


TTS024



13

1/8-27 NPT

6.3

24

1/2 GAS

6.3

24

M16 x 1.5

4

19

M14 x 1.5

13

M12 x 1.25

6.3

13

1/8-27 NPT

M5

19

M14x1.5

4

19

5/8-18 UNF

19

M14 x 1.5

4

19

1/8-27 NPT

13

M12 x 1.25

6.3

81

Wat

er T

emp

erat

ure

Sen

der

s


TTS032

Note: Replaces original yellow and violet parts

TTS033 TTS034

TTS035


TTS036 TTS037

TTS038


TTS039 TTS040


TTS043

Note: Replaces original light blue part

TTS044 TTS045

22

M16 x 1.5

13

1/8-27NPT

M5

13

1/8-27NPT

4

19

M14 x 1.5

4

13

M12 x 1.25

6.3

13

1/8-27 NPT

6.3

13

1/8-27NPT

6.3

21

1/8-27NPT

19

M14 x 1.25

19

5/8-18

4.7

1/2

1/8-27NPT

6.3


TTS046


TTS048 TTS049







1/2

1/8-27NPT

1/2

1/8-27NPT

6.3

1/2

1/8-27NPT

6.3

1/2

1/8-27NPT

6.3

22

M14 x1.5

4

oC110

21

3/8 GAS

4

oC60

oC120

oC60

19

M10 x 1

6.3

oC90

oC110

oC107 / 112

oC112 / 120

83

Wat

er T

emp

erat

ure

Sen

der

s



TTS064


TTS501 TTS503

TTS504


TTS505


TTS506

TTS507

TTS508 TTS509


oC102 / 115

20

M14 x 1.25

oC60

20

M14 x 1.25

oC120

19

M10 x 1

6.3

oC100

oC95

20

M14 x 1.25

oC115

22

M14 x 1.5

oC100

oC95

oC100

24

M12 x 1.5

oC120

22

M18 x 1.5

6.3 4.8

oC115


TTS510


TTS511

Note: Replaces original violet ring

TTS512

Note: Replaces original blue with yellow ring

TTS513 TTS514

Note: Replaces original blue with white ring

TTS515

Note: Replaces original part with grey ring

TTS516 TTS517

Note: Replaces original dark blue - white and yellow parts

TTS518

Note: Replaces original black part with dark blue ring

TTS519 TTS520


85

Part No. Spanner Thread Temp Ratings NotesTTS001 12 1/8 GASTTS002 17 M16 x 1.5TTS003 12 1/8 GASTTS004 12 1/8 GASTTS005 17 M16 x 1.5TTS006 17 M16 x 1.5TTS007 17 M16 x 1.5 Replaces original black and grey partsTTS008 13 1/8 GAS Replaces original black and grey partsTTS010 17 3/8 - 18 DRYSEAL THREADTTS013 12 1/8 GASTTS014 17 M16 x 1.25TTS015 12 M8 x 0.75TTS017 17 M16 x 1.5TTS018 17 M16 x 1.5TTS020 17 M16 x 1.5TTS021 13 M12 x 1.25TTS023 13 1/8 - 27 NPT Replaces original white partTTS024 13 1/8 - 27 NPTTTS025 19 M14 x 1.5TTS027 19 5/8 - 18 UNFTTS028 17 M16 x 1.5TTS029 19 5/8 - 18UNFTTS030 13 M 8 x 0.75TTS031 17 M16 x 1.5TTS032 13 1/8 - 27 NPT Replaces original yellow and violet partTTS033 24 1/2 GasTTS034 17 M16 x 1.5TTS035 19 M14 x 1.5 Replaces original brown partTTS036 13 M12 x 1.25TTS037 13 1/8 - 27NPTTTS038 - - Replaces original black partTTS039 19 M14 x 1.5TTS040 19 5/8 - 18UNF Replaces original black partTTS043 19 M14 x 1.5 Replaces original light blue partTTS044 19 1/8 - 27 NPTTTS045 13 M12 x 1.25TTS046 22 M16 x 1.5 Replaces original brown partTTS048 13 1/8 - 27 NPTTTS049 13 1/8 - 27 NPT Replaces original green partTTS050 19 M14 x 1.5TTS051 13 M12 x 1.25TTS052 13 1/8 - 27 NPT Replaces original white partTTS054 13 1/8 - 27 NPTTTS055 21 1/8 - 27 NPTTTS057 19 M14 x 1.25TTS058 19 3/8 - 18 DRYSEAL THREADTTS060 1/2 1/8 - 27NPTTTS061 1/2 1/8 - 27NPTTTS062 1/2 1/8 - 27NPTTTS063 1/2 1/8 - 27NPTTTS064 1/2 1/8 - 27NPTTTS501 22 M14 x 1.5 110CTTS503 21 3/8 Gas 60CTTS504 - - 120C Replaces original white partTTS505 - - 60C Replaces original red partTTS506 19 M10 x 1 90CTTS507 - - 110CTTS508 - - 107C / 112CTTS509 - - 112C / 120C Replaces original brown partTTS510 - - 102C / 115C Replaces original grey partTTS511 20 M14 x 1.25 60C Replaces original violet ringTTS512 20 M14 x 1.25 120C Replaces original blue with yellow ringTTS513 19 M10 x 1 100CTTS514 - - 95C Replaces original blue with white ringTTS515 20 M14 x 1.25 115C Replaces original part with grey ringTTS516 22 M14 x 1.5 100CTTS517 - - 95C Replaces original dark blue - white and yellow partsTTS518 - - 100C Replaces original black part with dark blue ringTTS519 24 M12 x 1.5 120CTTS520 22 M18 x 1.5 115C


85

Wat

er T

emp

erat

ure

Sen

der

s

This section has been included to assist with the identifi cation of Tridons extensive range of engine coolant sensors. Photographs and specifi cation tables are shown for each Tridon part number. Each specifi cation table contains spanner size, thread size, plug type and circuit diagram. The Tridon coolant sensor range has been developed to operate within original equipment manufacturers specifi cations. As Tridon coolant sensor circuits vary always refer to the Tridon vehicle application list to ensure the correct part number selection.

Coolant Temperature Sensors

Function

The coolant temperature sensor is a device designed to respond to

changes in coolant temperature, this response causes a change in signal

voltage which is returned to the vehicle computer (ECU). The registered

change in voltage signal is then processed by the ECU to determine the

engine temperature. The coolant temperature sensor is crucial for the

control of temperature based functions performed ECU (e.g. ignition,

instrumentation, fuel metering and transmission shifting).

There are two types of coolant temperature sensors, the thermocouple

type and more commonly used thermistor type, normally located in the

water jacket of the engine cylinder head or intake manifold. The thermistor

type contains conductive materials which respond to coolant temperature

changes. Two types of conductive material are used; material with a

positive temperature coeffi cient (PTC), where the resistance increases as

the temperature increases. Alternatively and more commonly used is

material with a negative temperature coeffi cient (NTC), which responds

with decreasing resistance as the temperature increases.

The coolant temperature sensor is critical to many temperature based

functions performed by the ECU, these include;

Electronic fuel injection system.

- Changes to injector pulse width.

- Operation idle speed solenoid.

Ignition Timing systems.

- Changes to spark timing.

Variable valve timing.

Transmission control.

Electric cooling fan switching control (if separate

fan switch is not used).


The coolant temperature sensor is an integral component in a vehicle

engine management system; a faulty coolant temperature sensor can result

in poor engine performance including diffi cult starting, poor fuel economy,

possible overheating and potential engine damage.

Coolant temperature sensors should be inspected every 20,000 kilometres,

the sensor should be checked for any visible signs of contaminant and

conductivity. Note the coolant itself, particularly old coolant, incorrect

coolant levels or mixture may cause the sensor to malfunction.

When a coolant temperature sensor malfunction or fault is suspected

the coolant temperature sensor should be checked and replaced by a

trained professional.

87

Coolant Temperature Sensor Testing Procedures

1. Remove the coolant temperature sensor from the vehicle.

2. Check the coolant temperature sensor for visible contaminant, conductivity or leaks.

3. Check correct coolant temperature sensor operation; Suspend the sensor in a beaker

fi lled with water so that the

bulb is covered.

Using an Ohmmeter, measure the resistance across the terminals,

(or terminal to the body of the sender). Heat the water until a simulated engine operating temperature is

achieved (80C - 90C). The sensor is designed to respond to the

change in temperature (as the water temperature increases the

sensor resistance will decrease or has a negative temperature

coeffi cient NTC). At low temperatures the resistance values may be several thousand

ohms () and reduce to as low as a few hundred ohms () at normal

engine operating temperatures.

The Tridon coolant temperature sensor range has been developed to

operate with OEM specifi cations. As coolant temperature sensor values

may vary, always refer to the Tridon Vehicle Application list to ensure

correct part number selection.

/HMMETER

7ATER

#OOLANT3ENSOR

Typical Coolant Temperature Sensor Circuit

#OOLANT3ENSOR$ASHBOARDINSTRUMENTS

s%NGINETEMPERATUREFUNCTIONSs&UELINJECTIONs3PARKTIMING

%#5

88

Coolant Temperature Sensors


25

3/8-18 Dry Seal

22

M16 x 1.5

17

M12 x 1.5

19

M12 x 1.5

19

M12 x 1.5

19

M12 x 1.5

17

3/8 GAS

6.3 6.3

19

3/8 GAS

19

M12 x 1.5

19

M12 x 1.5

19

3/8 GAS

19

M12 x 1.5

89

Co

ola

nt

Tem

per

atu

re S

enso

rs


TCS011 TCS020


TCS022


TCS024


TCS026


TCS029

Note: Replaces original white and black part

TCS030


TCS032

Note: Replaces original green and grey parts

TCS035


TCS040 TCS045 TCS050

Note: Replaces original dark blue part Note: Replaces original black part

19

3/8 GAS

19

M12 x 1.5

19

M12 x 1.5

19

3/8-18 NPT

19

M12 x 1.5

19

M12 x 1.5

19

3/8-18 NPT

19

M12 x 1.5

19

M14 x 1.5

19

M12 x 1.5


TCS055


TCS060


TCS065


TCS070


TCS075

Note: Replaces original red and dark blue parts

TCS080


TCS085 TCS090


TCS091


TCS093

Note: Replaces original white and black parts

TCS094


TCS095

Note: Replaces original black and yellow parts


19

M12 x 1.5

22

M10 x 1

19

M14 x 1.5

19

M12 x 1.5

19

M12 x 1.5

21

M12 x 1.5

17

M16 x 1.5

4

19

M12 x 1.5

19

M12 x 1.5

M12 x 1.5

17

M12 x 1.5

19

1/8-27NPT

91

Co

ola

nt

Tem

per

atu

re S

enso

rs


TCS096


TCS098


TCS099


TCS102 TCS106


TCS115



19

M12 x 1.5

19

M12 x 1.5

19

3/8 GAS

19

M12 x 1.5

Part No. Spanner Thread Notes

TCS011 25 3/8 -18 Dry Seal

TCS020 22 M16 x 1.5 Replaces original black part


TCS024 19 M12 x 1.5 Replaces original green part

TCS026 19 M12 x 1.5 Replaces original white part

TCS029 19 M12 x 1.5 Replaces original white and black part

TCS030 17 3/8 Gas Replaces original black part

TCS032 19 M12 x 1.5 Replaces original green and grey parts

TCS035 19 3/8 Gas Replaces original green part

TCS040 19 M12 x 1.5 Replaces original dark blue part

TCS045 19 M12 x 1.5





TCS070 19 3/8 - 18 NPT Replaces original black part

TCS075 19 M12 x 1.5 Replaces original red and dark blue parts

TCS080 19 M12 x 1.5 Replaces original brown part

TCS085 19 3/8 - 18 NPT


TCS091 - - Replaces original dark blue part

TCS092 19 M10 x 1

TCS093 19 M14 x 1.5 Replaces original white and black parts


TCS095 - - Replaces original black and yellow parts

TCS096 19 M12 x 1.5 Replaces original green part


TCS098 19 M10 x 1 Replaces original white part



TCS101 - -

TCS102 19 M12 x 1.5

TCS103 - - Replaces original black part

TCS104 - - Replaces original green part

TCS105 - - Replaces original dark blue and green parts


TCS107 22 M12 x 1.5

TCS108 22 M12 x 1.5

TCS109 19 M12 x 1.5

TCS110 21 M12 x 1.5

TCS111 - -

TCS112 19 -

TCS113 21 M12 x 1.5

TCS114 - -

TCS115 21 M12 x 1.5

TCS116 17 M16 x 1.5

TCS117 19 M12 x 1.5

TCS118 19 M12 x 1.5

TCS119 - M12 x 1.5

TCS120 17 M12 x 1.5

TCS121 19 1/8 - 27 NPT Replaces original black and red parts

TCS124 19 M12 x 1.5 Replaces original grey part

TCS125 - M12 x 1.5

TCS126 19 3/8 Gas

TCS127 19 1/8 - 27 NPT

TCS128 19 M12 x 1.5Replaces original black, grey, red and dark blue parts



TCS124

TCS125

TCS127

Note: Replaces original black, grey, red and dark blue parts

TCS128


This section has been included to assist with the identifi cation of Tridons extensive range of thermo fan switches. Photographs and specifi cation tables are shown for each Tridon part number. Each specifi cation table contains spanner size, thread size, plug type, circuit diagram and temperature rating. The Tridon thermo fan switch range has been developed to operate within original equipment manufacturers specifi cations. As Tridon thermo fan switch circuits vary always refer to the Tridon vehicle application list to ensure correct part number selection.

Thermo Fan Switches

Function

The thermo fan switch is a mechanical switching device designed to

respond to changes in coolant temperature allowing the operation of the

electric radiator thermo fan(s).

Switching control is achieved through a bimetal alloy leaf, which defl ects

with changes in temperature opening or closing a set of contacts.

Each switch is calibrated to specifi c ON/OFF temperature ratings.

There are many different circuit functions of the thermo fan switch with

variations depending on vehicle manufacturers specifi cations.

Common triggering operations are as follows:

Single Speed Fan Normally closed between terminals. Normally open between terminals. Normally closed between earth and terminals. Normally open between earth and terminals.

Dual Speed Fans Double circuit, normally open. Double circuit - one normally closed, one normally open. Independent circuits, normally open.


The thermo fan switch is an integral component in a vehicle cooling system;

a faulty fan switch can cause possible overheating and potential damage to

an engine.

Thermo fan switches should be inspected at regular service intervals.

The switch should be checked for any visible signs of contaminant and

conductivity. Note that the coolant itself, particularly old coolant, incorrect

coolant levels or mixture may cause the thermo fan switch to malfunction.

When a thermo fan switch malfunction or fault is suspected the thermo fan

switch should be checked and replaced by a trained professional.

94

Thermo FanSwitches

Thermo Fan Switch Testing Procedure

1. Remove the thermo fan switch from the vehicle.

2. Check the thermo fan switch for any visible signs of contaminant, conductivity or leaks.

3. Check correct thermo fan switch operation; Suspend the switch in a beaker fi lled with water so that the

bulb is covered.

Using an Ohmmeter, measure for continuity across the switch terminals (or terminal to the body of the sender).

Heat the water until the simulated fan switch operating temperature is achieved (ON/OFF temperature values located in fan switch

identifi cation guide).

When the correct ON switching temperature is achieved a change in the Ohmmeter will be reading given; an indication switching between

the contacts (0 or infi nite depending to the type of switch).

Allow the water to cool, as the water temperature reaches the OFF switching temperature the Ohmmeter will return to the original

reading (opposite of the previous step).

4. Replace the thermo fan switch if the readings are not as shown above.

Note: Thermo fan switch temperature ranges and switching types may vary. Some vehicles have more than one thermo fan switch and more than

one thermo fan.

Please refer to vehicle applications and diagrams for correct thermo fan switch application.

5. Other thermo fan circuit tests include; Correct thermo fan motor operation. Wiring tests, open and short circuits. Relay operation. Available voltage (check fuses).

The Tridon thermo fan switch range has been developed to operate with

OEM specifi cations. As thermo fan switch temperature values may vary,

always refer to the Tridon Vehicle Application list to ensure correct part

number selection.

/HMMETER

4HERMO&AN3WITCH

7ATER

Typical Thermo Fan Switch Circuit

)GNITION3WITCH2ELAY

&ROM)GNITION3WITCH

&ROM"ATTERY

&USE

&AN-OTOR 4HERMAL3WITCH

95


29

M22 x 1.5

6.3 6.3

oCon 90off 80

29

M22 x 1.5

6.3 6.3

oCon 85off 75

29

M22 x 1.5

6.3 6.3

oCon 95off 90

29

M22 x 1.5

oCon 95off 90

29

M22 x 1.5

oC

22

M14 x 1.5

4.8 4.8

oCon 102off 97

22

M14 x 1.5

6.3 6.3

oCon 95off 90

24

M14 x 1.5

oC

22

M14 x 1.5

6.3 6.3

oCon 100off 95

29

M22 x 1.5

6.3 6.3

oCon 90off 85

21

3/8 GAS

6.3

oCon 87off 82

21

3/8 GAS

6.3

oCon 95off 90

on 95-off 85on 102-off 87




TFS100 TFS101 TFS102





17

M16 x 1.5

oCon 97off 92

17

M16 x 1.5

oCon 90off 85

17

M16 x 1.5

6.3

oCon 97off 92

21

M16 x 1.5

oCon 90off 85

22

M16 x 1.5

oCon 92off 87

21

M16 x 1.5

oCon 90off 85

17

M16 x 1.5

oCon 90off 85

22

M16 x 1.5

oCon 92off 82

24

M16 x 1.5

oCon 92off 87

22

M16 x 1.5

oCon 92off 87

22

M16 x 1.5

oCon 105off 90

22

M16 x 1.5

oCon 92off 87

97

Th

erm

o F

an S

wit

ches






22

M16 x 1.5

oCon 92off 77

24

M18 x 1.5

oCon 112off 107

24

M18 x 1.5

oCon 95off 90

27

M16 x 1.5

4

oCon 92off 87

21

M16 x 1.5

oCon 85off 80

21

M16 x 1.5

oCon 90off 85

21

M16 x 1.5

oCon 85off 80

29

M22 x 1.5

6.3 6.3

oCon 92off 87

17

M16 x 1.5

6.3

oCon 90off 85

17

M16 x 1.5

oCon 107off 102

17

M16 x 1.5

oCon 97off 92

17

M16 x 1.5

6.3

oCon 85off 80







21

M16 x 1.5

oCon 85off 80

22

M16 x 1.5

oCon 85off 80

22

M16 x 1.5

oCon 85off 80

27

M16 x 1.5

oCon 85off 80

22

M16 x 1.5

oCon 95off 85

29

M22 x 1.5

6.3 6.3

oCon 102off 97

29

M22 x 1.5

6.3 6.3

oCon 115off 110

6.3 6.3

oCon 115off 105

22

M16 x 1.5

6.3 6.3

oCon 95off 90

17

M16 x 1.5

oCon 90off 85

17

M16 x 1.5

oCon 95off 90

21

M16 x 1.5

oCon 90off 85

99

Th

erm

o F

an S

wit

ches






17

M16 x 1.5

oCon 85off 80

17

M16 x 1.5

oCon 105off 100

17

M16 x 1.5

oCon 50off 45

22

M16 x 1.5

oCon 87off 82

22

M16 x 1.5

oCon 100off 95

24

M18 x 1.5

oCon 100off 95

17

M16 x 1.5

oCon 50off 45

17

M16 x 1.5

oCon 110off 105

29

M22 x 1.5

oC

29

M22 x 1.5

oCon 100off 95

29

M22 x 1.5

oC

29

M22 x 1.5

oCon 95-off 90

on 105 -off 100on 95-off 90

on 120 -off 115

on 105-off 100on 120 -off 115





Note: Replaces original black part with violet ring



29

M22 x 1.5

oC

29

M22 x 1.5

oC

29

M22 x 1.5

oC

22

M16 x 1.5

oCon 90off 85

27

M16 x 1.5

4

oCon 85off 80

29

M22 x 1.5

6.3 6.3

oCon 92off 87

29

M22 x 1.5

6.3 6.3

oCon 87off 77

29

M22 x 1.5

oCon 95off 90

21

M16 x 1.5

4

oCon 92off 87

6.3 6.3

oCon 92off 87

22

M16 x 1.5

oCon 92off 82

29

M22 x 1.5

oCon 95off 90

on 105-off 100on 120-off 115

on 100-off 95on 105 -off 100

on 110-off 105on 120 -off 115

101

Th

erm

o F

an S

wit

ches





Note: Replaces original part with brown ring


21

3/8 GAS

4

oCon 72off 67

29

M22 x 1.5

oCon 92off 82

27

M16 x 1.5

4

oCon 95off 90

29

M22 x 1.5

oCon 92off 87

29

M22 x 1.5

oCon 97off 92

29

M22 x 1.5

oCon 100off 95

22

M14 x 1.5

6.3 6.3

oCon 95off 90

29

M16 x 1.5

oCon 112off 107

22

M14 x 1.5

4

oCon 100off 95

29

M22 x 1.5

oCon 95off 90

17

M16 x 1.5

oCon 92off 87

21

M12 x 1.5

oCon 105off 100



Note: Replaces original part with yellow ring






17

M16 x 1.5

oCon 90off 85

21

M16 x 1.5

4

oCon 97off 92

17

3/8 GAS

oCon 87off 82

21

M16 x 1.5

oCon 95off 90

29

M22 x 1.5

oCon 95off 90

21

M16 x 1.5

oCon 90off 85

24

3/8 GAS

6.3

oCon 92off 87

24

M14 x 1.5

oCon 110off 105

24

3/8 GAS

6.3

oCon 100off 95

17

3/8 GAS

oCon 95off 90

17

M16 x 1.5

6.3

oCon 90off 85

29

M22 x 1.5

oCon 87-off 77on 92-off 82

103

Th

erm

o F

an S

wit

ches






29

M22 x 1.5

oC

29

M22 x 1.5

oC

29

M22 x 1.5

oC

22

M14 x 1.5

oC

29

M22 x 1.5

oC

29

M22 x 1.5

oC

29

M22 x 1.5

oC

22

M22 x 1.5

oC

29

M22 x 1.5

oC

29

M22 x 1.5

oC

22

M14 x 1.5

oC

29

M22 x 1.5

oC

on 92-off 87on 105-off 100



on 100-off 95on 107-off 102






on 110-off 105on 120-off 115




Note: Replaces original part with red ring


Note: Replaces original red part Note: Replaces original dark blue part


Note: Replaces original grey part Note: Replaces original black part Note: Replaces original green part




oC

22

M16 x 1.5

oCon 95off 85

29

M22 x 1.5

oCon 87off 82

29

M22 x 1.5

oCon 102off 97

29

M22 x 1.5

oCon 100off 95

29

M22 x 1.5

oC

24

M18 x 1.5

oCon 95off 90

17

M16 x 1.5

oCon 100off 95

22

M16 x 1.5

oCon 95off 90


on 95-off 90on 105-off 100

105

Th

erm

o F

an S

wit

ches






Note: To ensure correct product selection please check illustrations and specifi cations as values may differ.106

Thermo Fan SwitchStyle Variations

This section has been

included to assist with Tridon

thermo fan switch selection.

Each thermo fan switch style

includes corresponding Tridon

part number with temperature

range, photograph and

specifi cation table.

29

M22 x 1.5

Style A

22

M14 x 1.5

Style B

21

3/8 GAS

6.3

Style C

17

M16 x 1.5

Style D

17

M16 x 1.5

6.3

Style E

21

M16x1.5

Style F

17

M16x1.5

Style G

22

M16x1.5

Style H

Part No. on off TFS100 90oC 80oC

TFS101 85oC 75oC

TFS102 95oC 90oC

TFS109 90oC 85oC

TFS135 92oC 87oC

TFS145 102oC 97oC

TFS170 92oC 87oC

TFS171 87oC 77oC


TFS108 100oC 95oC


TFS111 95oC 90oC


TFS114 90oC 85oC


TFS136 90oC 85oC


TFS197 95oC 90oC


TFS153 85oC 80oC


TFS126 105oC 90oC

TFS128 92oC 77oC

6.3 6.3 6.3 6.3

Note: To ensure correct product selection please check illustrations and specifi cations as values may differ. 107

Th

erm

o F

an S

wit

ches

27

M16 x 1.5

4

Style I

17

M16 x 1.5

Style J

22

M16 x 1.5

Style K

24

3/8 GAS

6.3

Style L

29

M22x1.5

Style M

29

M22 x 1.5

Style N

29

M22 x 1.5

Style O

29

M22 x 1.5

Style P

24

M18 x 1.5

Style Q


TFS169 85oC 80oC

TFS183 95oC 90oC


TFS138 97oC 92oC

TFS154 105oC 100oC

TFS160 110oC 105oC


TFS220 95oC 85oC


TFS202 100oC 95oC


120oC 115oC

TFS165 105oC 100oC

120oC 115oC

TFS215 110oC 105oC

120oC 115oC


105oC 100oC

TFS166 100oC 95oC

105oC 100oC

TFS224 95oC 90oC

105oC 100oC


102oC 87oC

TFS205 87oC 77oC

92oC 82oC

TFS208 95oC 85oC

102oC 92oC


TFS221 87oC 82oC


TFS225 95oC 90oC

108


TridonPart No.

Style type,Common Thread, Plug and Circuit

Terminals Temp C on-off

N/OTerm

N/CTerm

N/OGround

N/CGround

DualN/O-N/O

DualN/C-N/O

TFS100 A 2 90-80 X

TFS101 A 2 85-75 X

TFS102 A 2 95-90 X

TFS103 2 95-90 X

TFS104 O 3 95-85 and 102-87 X

TFS105 2 102-97 X

TFS106 B 2 95-90 X

TFS107 3 90-86 and 99-94 X

TFS108 B 2 100-95 X

TFS109 A 2 90-85 X

TFS110 C 1 87-82 X

TFS111 C 1 95-90 X

TFS113 D 1 97-92 X

TFS114 D 1 90-85 X

TFS115 E 1 97-92 X

TFS116 2 90-85 X

TFS117 2 92-87 X

TFS119 F 2 90-85 X

TFS120 G 1 90-85 X

TFS121 2 92-82 X

TFS123 2 92-87 X

TFS124 H 2 92-87 X

TFS126 H 2 105-90 X

TFS127 2 92-87 X

TFS128 H 2 92-77 X

TFS129 2 112-107 X

TFS130 2 95-90 X

TFS131 I 2 92-87 X

TFS132 2 85-80 X

TFS133 2 90-85 X

TFS134 2 85-80 X

TFS135 A 2 92-87 X

TFS136 E 1 90-85 X

TFS137 J 1 107-102 X

TFS138 J 1 97-92 X

TFS139 1 85-80 X

TFS140 2 85-80 X

TFS141 2 85-80 X

TFS142 2 85-80 X

TFS143 2 85-80 X

TFS144 2 95-85 X

TFS145 A 2 102-97 X

TFS146 2 115-110 X

TFS147 2 115-105 X

TFS148 2 95-90 X

109

TridonPart No.


Terminals Temp C on-off

N/OTerm

N/CTerm

N/OGround

N/CGround

DualN/O-N/O

DualN/O-N/O

TFS150 1 90-85 X

TFS151 1 95-90 X

TFS152 2 90-85 X

TFS153 G 1 85-80 X

TFS154 J 1 105-100 X

TFS155 1 50-45 X

TFS156 2 87-82 X

TFS157 K 2 100-95 X

TFS158 Q 2 100-95 X

TFS159 1 50-45 X

TFS160 J 1 110-105 X

TFS161 3 105-100 and 120-115 X

TFS162 P 2 100-95 X

TFS163 N 3 95-90 and 105-100 X

TFS164 M 3 95-90 and 120-115 X

TFS165 M 3 105-100 and 120-115 X

TFS166 N 3 100-95 and 105-100 X

TFS167 3 110-105 and 120-115 X

TFS168 2 90-85 X

TFS169 I 2 85-80 X

TFS170 A 2 92-87 X

TFS171 A 2 87-77 X

TFS173 2 95-90 X

TFS174 1 92-87 X

TFS175 2 92-87 X

TFS176 2 92-82 X

TFS179 2 95-90 X

TFS181 2 72-67 X

TFS182 2 92-82 X

TFS183 I 2 95-90 X

TFS184 2 92-87 X

TFS185 2 97-82 X

TFS186 2 100-95 X

TFS187 2 95-90 X

TFS188 2 112-107 X

TFS189 2 100-95 X

TFS190 2 95-90 X

TFS191 1 92-87 X

TFS193 2 105-100 X

TFS194 1 90-85 X

TFS195 1 90-85 X

TFS196 1 97-92 X

TFS197 F 2 95-90 X

TFS198 2 95-90 X

TFS199 2 90-85 X

110

TridonPart No.


Terminals Temp Con-off

N/OTerm

N/CTerm

N/OGround

N/CGround

DualN/O-N/O

DualN/C-N/O

TFS200 L 1 92-87 X

TFS201 2 110-105 X

TFS202 L 1 100-95 X

TFS203 1 95-90 X

TFS204 1 90-85 X

TFS205 O 3 87-77 and 92-82 X

TFS206 3 92-87 and 105-100 X

TFS207 3 97-87 and 100-95 X

TFS208 O 3 95-85 and 102-92 X

TFS209 3 100-95 and 107-102 X

TFS210 3 87-77 and 92-82 X

TFS211 3 90-80 and 97-87 X

TFS212 3 87-77 and 92-82 X

TFS213 3 95-90 and 102-97 X

TFS214 3 80-75 and 87-82 X

TFS215 M 3 110-105 and 120-115 X

TFS217 3 90-85 and 97-92 X

TFS218 3 97-87 and 102-97 X

TFS219 Note 1 4 95-90 and 102-97

TFS220 K 2 95-85 X

TFS221 P 2 87-82 X

TFS222 2 102-97 X

TFS223 2 100-95 X

TFS224 N 3 95-90 and 105-100 X

TFS225 Q 2 95-90 X

TFS226 1 105-100 X

TFS228 2 95-90 X

E,G Normallyclosed betweenground and terminal

C,D,J,L Normallyopen between groundand terminal

A,B,H,I,K,P,Q Normally open between terminals

F Normally closed between terminals

Note 1: TFS219 only Two independant circuits normally open

M Double circuit one normally closed theother open

N,O Double circuit normally open

Temperature Conversion F = ( C x 1.8) + 32

Refer to page 106-107 for common switch combinations with temperature variations.

Single Circuit Double Circuit

This section has been included to assist with the identifi cation of Tridons extensive range of stop light switches. Photographs and specifi cation tables are shown for each Tridon Part number. Each specifi cation table contains spanner size, thread size, plug type and circuit diagram. The Tridon stop light switch range has been developed to operate within original equipment manufacturers specifi cations. As Tridon stop light switch circuits vary always refer to the Tridon Vehicle Application list to ensure correct part number selection.

Stop Light Switches

Function

The stop light switch is a mechanical device whose primary function is

to control circuit switching for the operation of the vehicles stop lights.

Normally located within the brake pedal assembly, the stop light switch is

activated by the application of the brake pedal, closing a set of contacts

allowing current to fl ow through the stop light circuit.

A secondary function for the stop light switch is used on vehicles with

cruise control. The stop light switch is used to interrupt the cruise

control circuit, disengaging the cruise control when the brake is applied.

This circuit uses a secondary set of contacts which open when the

brake pedal is applied.

Typical Stop Light Circuit

3TOP,IGHT3WITCH

3TOP,IGHTS

&USE

Stop Light Switches

112


When a stop light switch malfunction or fault is suspected, the stop light

switch should be checked and replaced by a trained professional.

Stop Light Switch Testing Procedure

1. Ensure correct plunger adjustment. The stop light switch plunger should be slightly compressed

when the brake pedal is in a resting position. When the brake pedal is applied the plunger should release.

2. Check correct stop light switch operation. Using an Ohmmeter, measure for continuity across the stop light

switch terminals. With the plunger depressed (the brake pedal in a resting position),

the reading should be infi nite or open circuit. As the plunger is slowly released (application of the brake pedal),

the reading should become zero (0), or show a closed circuit between

the contacts.

3. Replace the stop light switch if the readings are not as shown above.

Note: For vehicles with cruise control, the stop light switch may

have more than two terminals and contain more than one circuit;

refer to vehicle applications and diagrams for correct stop light

switch application.

4. Other stop light circuit tests include; Faulty or blown stop light globes. Wiring tests, open and short circuits. Available voltage (check fuses).

The Tridon stop light switch range has been developed to operate

with OEM specifi cations. As switch circuits and operation may vary,

always refer to the Tridon Vehicle Application list to ensure correct

part number selection.

/HMMETER

3TOP,IGHT3WITCH

113


14

M10 x 1.25

14

M10 x 1.25

14

M10 x 1.25

14

M10 x 1.25

4

14

M10 x 1.25

14

M10 x 1.25

14

M10 x 1.25

4

14

M10 x 1.25

4

14

M10 x 1.25

14

M10 x 1.25

14

M10 x 1.25

6.3 6.3

14

M10 x 1.25


TBS001

TBS002

TBS003

TBS004

TBS005

TBS006

TBS007

TBS008

TBS009

TBS010

TBS011

TBS012


14

M10 x 1.25

14

M10 x 1.25

14

M10 x 1.25

17

M12x 1

6.3 6.3

14

M10 x 1.25

14

M10 x 1.25

14

M12 x 1.5

6.3 6.3

14

M10 x 1.25

6.3 6.3

14

M10 x 1.25

14

M10 x 1.25

M12 x 1.75

6.3 6.3

1/2-20 UNF

6.3 6.3

115

Sto

p L

igh

t S

wit

ches


TBS014

TBS015

TBS016

TBS017

TBS018

TBS019

TBS020

TBS021

TBS022

TBS023

TBS024

TBS025

6.3 6.3

22

6.3 6.3

M16 x 1.5

22

M12 x 1.5

6.3 6.3

M12 x 1.5


TBS026

TBS027

TBS028

TBS029

TBS030

TBS031

TBS032

TBS034

TBS035

TBS036

TBS037

TBS038


14

M10 x 1.25

14

M10 x 1.25

M12 x 1.5

14

M10 x 1.25

22

1/8-27 NPT

6.3 6.3

6.3 6.3

117

Sto

p L

igh

t S

wit

ches


TBS039

TBS040

TBS041

TBS042

TBS043

TBS044

TBS045

TBS046

TBS047

TBS048

TBS049

TBS050

6.3 6.3

6.3 6.3

6.3 6.3

6.3 6.3

6.3 6.3


TBS051

TBS052

TBS053

TBS055

TBS056

TBS059

TBS060

TBS061

TBS064

TBS065

TBS068

TBS069


6.3 6.3

22

M10 x 1

6.3 6.3

119

TBS070

TBS071

Part No.

Spanner Thread Circuit Type

TBS001 14 M10 x 1.25 Dual N/O - N/C

TBS002 14 M10 x 1.25 N/C

TBS003 14 M10 x 1.25 N/C

TBS004 14 M10 x 1.25 N/C

TBS005 14 M10 x 1.25 N/C

TBS006 14 M10 x 1.25 N/C

TBS007 14 M10 x 1.25 N/C

TBS008 14 M10 x 1.25 N/C

TBS009 14 M10 x 1.25 N/C

TBS010 14 M10 x 1.25 N/C

TBS011 14 M10 x 1.25 N/C

TBS012 14 M10 x 1.25 N/C

TBS014 14 M10 x 1.25 N/C

TBS015 14 M10 x 1.25 N/C

TBS016 14 M10 x 1.25 Dual N/O - N/C

TBS017 14 M10 x 1.25 Dual N/O - N/C

TBS018 14 M10 x 1.25 Dual N/O - N/C

TBS019 14 M10 x 1.25 Dual N/C - N/C

TBS020 14 M10 x 1.25 Dual N/O - N/C

TBS021 14 M12 x 1.5 N/C

TBS022 - M12 x 1.75 N/C

TBS023 17 M12 x 1 N/C

TBS024 14 M10 x 1.25 N/C

TBS025 - 1/2 - 20 UNF N/C

TBS026 - - N/C

TBS027 22 - N/C

TBS028 - - N/C

TBS029 - - N/C

TBS030 - - Dual N/O - N/C

TBS031 - - N/C


TBS033 17 M12 x 1 Dual N/O - N/C

TBS034 - M16 x 1.5 N/C

Part No.

Spanner Thread Circuit Type

TBS035 - - Dual N/C - N/C


TBS037 22 M12 x 1.5 N/C

TBS038 - M12 x 1.5 N/C


TBS040 - - N/C

TBS041 14 M10 x 1.25 N/C

TBS042 14 M10 x 1.25 Dual N/O - N/C

TBS043 - - N/C

TBS044 22 1/8 - 27 NPT N/O

TBS045 14 - N/C

TBS046 - - N/C

TBS047 - - N/C

TBS048 - M10 x 1.5 Dual N/O - N/C

TBS049 - M12 x 1.5 Dual N/O - N/C

TBS050 - - N/C


TBS052 - - N/C




TBS056 - - N/C

TBS057 - - N/C



TBS060 - - N/O


TBS064 - - N/O


TBS068 - - N/O

TBS069 - - N/O

TBS070 - - N/O

TBS071 22 M10 x 1 N/O


Sto

p L

igh

t S

wit

ches


N/O = Normally Open

120

This section has been included to assist with the identifi cation of Tridons extensive range of reverse light switches. Photographs and specifi cation tables are shown for each Tridon part number. Each specifi cation table contains spanner size, thread size, plug type and circuit diagram. The Tridon reverse light switch range has been developed to operate within original equipment manufacturers specifi cations. As Tridon reverse light switch circuits vary always refer to the Tridon vehicle application list to ensure correct part number selection.

Reverse Light Switches

Function

The reverse light switch is a mechanical device whose primary function

is to control circuit switching for the operation of the vehicle reverse lights.

Normally located within the gearbox (manual transmission), the reverse light

switch is activated when reverse gear is selected. There are commonly two

different switch circuit types, which may vary depending on vehicle

manufacturers specifi cations.

Common Switch Circuits

Normally Open Contacts.

Normally Closed Contacts.


When a reverse light switch malfunction or fault is suspected, the reverse

light switch should be checked and replaced by a trained professional.

Reverse Light Switches Testing Procedure

1. Remove the reverse light switch from the vehicle.

2. Check the reverse light switch for visible faults or oil leaks.

3. Check correct reverse light switch operation, using an Ohmmeter, measure for continuity across the reverse light switch terminals.

Normally CLOSED circuit type reverse light switch. With the plunger depressed, the reading should be infi nite

or open circuit. Slowly release the plunger to the resting position, the reading should

become zero (0), or show a closed circuit between the contacts.

121

Testing Procedure (cont.)

Normally OPEN circuit type reverse light switch. With the plunger depressed, the reading should be zero (0), or show a

closed circuit between the contacts. Slowly release the plunger to the resting position, the reading should be

infi nite or open circuit.

4. Replace the reverse light switch if the readings are not as shown above.

5. Other reverse light circuit tests include; Faulty or blown reverse light globes. Wiring tests, open and short circuits. Available voltage (check fuses).

The Tridon reverse light switch range has been developed to operate

with OEM specifi cations. As switch circuits and operation may vary,

always refer to the Tridon Vehicle Application list to ensure correct part

number selection.

Typical Reverse Light Circuit

2EVERSE,IGHT3WITCH

)GNITION3WITCH

2EVERSE,IGHTS

&USE

Reverse Light Switches


/HMMETER

2EVERSE,IGHT3WITCHES

122

21

M14 x 1.5

21

M14 x 1.5

21

M14 x 1.5

21

M16 x 1.5

19

M14 x 1.5

4

25

M18 x 1.5

27

M18 x 1.5

19

M14 x 1.5

19

M14 x 1.5

24

M14 x 2

4

24

M14 x 2

24

M14 x 2

Rev

erse

Lig

ht

Sw

itch

es


TRS001

TRS004

TRS007

TRS010

TRS002

TRS005

TRS008

TRS011

TRS003

TRS006

TRS009

TRS012

123

19

M12 x 1.25

4

19

M12 x 1.25

4

19

M12x 1.25

24

M14 x 1.5

19

M12 x 1.25

19

M14 x 1.5

4

19

M14 x 1.5

4

19

M14 x 1.5

22

M14 x 1.5

4.6

19

M12 x 1.5

6.3 6.3

19

M12 x 1.5

6.3 6.3

22

M14 x 1.5

3.5


TRS013

TRS016

TRS019

TRS022

TRS014

TRS017

TRS020

TRS023

TRS015

TRS018

TRS021

TRS024


19

3/8-16UNC

4.5

19

M12 x 1.5

27

M16 x 1.5

6.3 6.3

19

M14 x 1.5

4

22

M14 x 1.5

6.3 6.3

22

M14 x 1.5

27

M18 x 1.5

21

M12 x 1.5

22

M18 x 1.5

21

M12 x 1.5

24

M14 x 2

22

M16 x 1.5

125

Rev

erse

Lig

ht

Sw

itch

es


TRS025

TRS028

TRS031

TRS034

TRS026

TRS029

TRS032

TRS037

TRS027

TRS030

TRS033

TRS038

19

M14 x 1.5

24

M14 x 2

24

M14 x 2

19

M14 x 1.5

19

M14 x 1.5

27

M18 x 1.5

22

M16 x 1.5

22

M12 x 1.5

22

M16x 1.5

24

M14 x 2

24

M14 x 2


TRS040

TRS043

TRS046

TRS049

TRS041

TRS044

TRS047

TRS050

TRS042

TRS045

TRS048

TRS051


24

M14 x 2

24

M14 x 2

22

M16 x 1.5

6.3 6.3

22 22

M16 x 1.5

24

M14 x 2


N/O = Normally Open

127

Rev

erse

Lig

ht

Sw

itch

es


TRS052

TRS055

TRS053

TRS056

TRS054

TRS059

Part No. Spanner Thread Circuit TypeTRS001 21 M14 x 1.5 N/OTRS002 21 M14 x 1.5 N/OTRS003 21 M14 x 1.5 N/OTRS004 21 M16 x 1.25 N/OTRS005 19 M14 x 1.5 N/OTRS006 25 M18 x 1.5 N/OTRS007 27 M18 x 1.5 N/OTRS008 19 M14 x 1.5 N/OTRS009 19 M14 x 1.5 N/OTRS010 24 M14 x 2.0 N/OTRS011 24 M14 x 2.0 N/OTRS012 24 M14 x 2.0 N/OTRS013 19 M12 x 1.25 N/CTRS014 19 M12 x 1.25 N/OTRS015 19 M12 x 1.25 N/CTRS016 24 M14 x 1.5 N/CTRS017 19 M12 x 1.25 N/CTRS018 19 M14 x 1.5 N/OTRS019 19 M14 x 1.5 N/OTRS020 19 M14 x 1.5 N/OTRS021 22 M14 x 1.5 N/OTRS022 19 M12 x 1.5 N/OTRS023 19 M12 x 1.5 N/OTRS024 22 M14 x 1.5 N/CTRS025 19 3/8 - 16 UNC N/OTRS026 19 M12 x 1.5 N/OTRS027 27 M16 x 1.5 N/O

Part No. Spanner Thread Circuit TypeTRS028 19 M14 x 1.5 N/CTRS029 22 M14 x 1.5 N/CTRS030 22 M14 x 1.5 N/OTRS031 27 M18 x 1.5 N/OTRS032 21 M12 x 1.5 N/OTRS033 22 M18 x 1.5 N/OTRS034 21 M12 x 1.5 N/OTRS037 24 M14 x 2 N/OTRS038 22 M16 x 1.5 N/OTRS039 21 M14 x 1.5 N/OTRS040 19 M14 x 1.5 N/CTRS041 24 M14 x 1.5 N/OTRS042 24 M14 x 2 N/CTRS043 19 M14 x 1.5 N/OTRS044 19 M14 x 1.5 N/OTRS045 - - N/OTRS046 27 M18 x 1.5 N/OTRS047 22 M16 x 1.5 N/OTRS048 22 M12 x 1.5 N/OTRS049 22 M16 x 1.5 N/OTRS050 24 M14 x 2 N/OTRS051 24 M14 x 2 N/OTRS052 24 M14 x 2 N/OTRS053 24 M14 x 2 N/OTRS054 22 M16 x 1.5 N/OTRS055 22 N/O


Alphabetical Index page

Coolant Temperature Sensors 86

Function - Coolant Temperature Sensors 87

Function - Oil Pressure Senders and Sensors 68

Function - Reverse Light Switches 121

Function - Stop Light Switches 112

Function - Thermo Fan Switches 94

Function - Water Temperature Senders 77

Guarantee 1

Identifi cation Guide - Coolant Temperature Sensors 89

Identifi cation Guide - Oil Pressure Senders and Sensors 70

Identifi cation Guide - Reverse Light Switches 123

Identifi cation Guide - Stop Light Switches 114

Identifi cation Guide - Thermo Fan Switches 96

Identifi cation Guide - Water Temperature Senders 79

Merchandising 4

Oil Pressure Senders and Sensors 67

Packaging 3

Product Range 2

Quick Reference Guide - Coolant Temperature Sensors 92

Quick Reference Guide - Oil Pressure Senders and Sensors 75

Quick Reference Guide - Reverse Light Switches 127

Quick Reference Guide - Stop Light Switches 119

Quick Reference Guide - Thermo Fan Switches 108

Quick Reference Guide - Water Temperature Senders 85

Replacement - Coolant Temperature Sensors 87

Replacement - Oil Pressure Senders and Sensors 68

Replacement - Reverse Light Switches 121

Replacement - Stop Light Switches 112

Replacement - Thermo Fan Switches 94

Replacement - Water Temperature Senders 77

Reverse Light Switches 120

Stop Light Switches 111

Style Variations - Thermo Fan Switches 106

Testing - Coolant Temperature Sensors 87

Testing - Oil Pressure Senders and Sensors 68

Testing - Reverse Light Switches 121

Testing - Stop Light Switches 112

Testing - Thermo Fan Switches 94

Testing - Water Temperature Senders 77

Thermo Fan Switches 93

Vehicle Application List 5

Water Temperature Senders 76

128128

AdministratorRectangle





AdministratorText BoxVehicle Application Listing

Make and Model

Year Engine Part Number

NotesStart Finish Cyl Size ModelOilPressure

WaterTemp

CoolantSensor

Fan Switch

Stop Light

Reverse Light

6

33 Ti, Boxer 1985 1989 4 1.5L AR305 TPS019 TFS100

33 All 1988 1992 4 1.7L All TPS019 TCS040 TFS100 TBS021 Stop Light Switch on Sport models only

75 V6 1986 1992 V6 2.5L,3.0L AR019,AR61 TPS020 TTS520 TCS026 TFS101

75 Twin Spark 1988 1992 4 2.0L AR062.24 TPS020 TCS040 TFS101

90 Leaded Fuel 1985 1985 V6 2.5L AR016.46 TPS020 TCS026 TFS101

90 Unleaded Fuel 1985 1988 V6 2.5L AR019.11 TPS020 TFS101

147 All 08/2001 on 4, V6 ALL TPS043 TCS113 TBS054

156 Twin Spark 1999 10/2000 4 2.0L AR 32310 TPS043 TCS102TCS110

TBS045 2 x Coolant Sensors, check illustrations

156 2.0L 10/2000 on 4 2.0L TPS043 TCS113 TBS054

156 2.5L V6 1999 on V6 2.5L AR32405 TPS043 TCS113

156 3.0L V6 1999 on V6 3.0L TPS043

156 GTA 4D Sedan 2002 2004 V6 3.2L 932A000 TPS043 TCS113 TBS054

164 3.0L V6 1989 1991 V6 3.0L AR064.10 TPS040 TCS040 TFS101

164 3.0L V6 1989 1992 V6 3.0L AR643.01 TPS040 TCS040

166 4D Sedan 1999 2001 V6 3.0L AR343 TPS043 TCS110 TBS031TBS032

2 x Stop Light Switches, check illustrations

166 4D Sedan 2001 on V6 3.0L AR36101 TPS043 TCS113 TBS054

Alfasud All 1974 1988 4 ALL TPS019 TFS100 TBS021

Alfetta & Giulietta All 1974 1986 4 ALL TPS020 TFS101

GT 2D Coupe (incl JTS) 2004 on 4, V6 ALL TPS043 TCS113

GTV 2000 1977 1981 4 2.0L AR162 TFS101

GTV GTV 2.0L 1981 1986 4 2.0L AR016 TPS007 TFS101

GTV 6 1983 1988 V6 2.5L TPS020 TCS026 TFS101

GTV All 1998 on 4 2.0L AR16201 TPS043 TTS520 TCS096 TBS031

GTV V6 2D COUPE 05/1998 on V6 3.0L AR16102 TPS043 TCS110 TBS031 2 x Stop Light Switches, check illustrations

Spider Milennium 11/1999 03/2000 4 2.0L AR32301 TPS043 TTS520 TCS110

Spider Twin Spark with luxury pack

07/2000 09/2002 4 2.0L AR16201 TPS020 TTS520 TCS096 TFS101 TBS031

Spider Duetto & Veloce 12/2001 09/2003 4 2.0L AR32301 TPS020 TTS520 TBS031

Spider JTS Lusso 10/2003 01/2005 4 2.0L 937A1000 TPS043 TTS520 TCS113 TBS054

Spider V6 2D Convertible 06/2001 09/2003 V6 3.0L AR16102 TPS043 TTS520 TCS113 TBS031

Audi

80 CC 1986 1987 4 1.8L JN TPS030TPS031TPS045

TCS098 TBS038 3 x Oil Pressure Switches, check illustrations

80 1.8E Quattro 1988 1989 4 1.8L SD TPS021TPS030TPS031TPS042

TCS098 TFS103TFS104

TBS038 4 x Oil Pressure Switches & 2 x Thermo Fan Switches, check illustrations

Alfa Romeo

7Vehicle Application List

Make and Model



WaterTemp

CoolantSensor

Fan Switch

Stop Light

Reverse Light

80 2.0 & 2.0S 1989 1992 4 2.0L 3A,AAD,ABK

TPS030TPS031TPS042TPS045

TCS091TCS098

TFS103TFS104

TBS038 4 x Oil Pressure Switches, 2 x Coolant Sensor & 2 x Thermo Fan Switches, check illustrations

80 2.3 1992 1993 5 2.3L NG TPS021TPS030

TFS103TFS104

TBS038 2 x Oil Pressure Switches & 2 x Thermo Fan Switches, check Illustrations

80 2.3E 1992 1993 5 2.3L NG TPS030TPS045

TBS038 2 x Oil Pressure Switches, check illustrations

80 2.6E (incl Cab) 1992 1999 V6 2.6L ABC TPS045TPS046

TFS103TFS104


80 2.6E Quattro & 2.8E 1992 1999 V6 2.6L,2.8L AAK, ABC TPS045TPS046

TCS098 TFS103TFS104


90 Sport & Quattro 1989 1992 5 2.3L 7A, NG TPS030TPS045

TFS103TFS104


100 CD 1983 1991 5 2.1L KF, HX, NF TPS021TPS030TPS031TPS042

TFS103TFS104

TBS038 4 x Oil Pressure Switches & 2 x Thermo Fan Switches, check illustrations

100 CD 1990 1991 5 2.3L AAR TPS021TPS030

TFS208 TBS038 2 x Oil Pressure Switches, check illustrations

100 2.6E & 2.8E (incl Quattro)

1992 1994 V6 2.6L,2.8L ABC, AAH TPS021TPS042TPS046

TCS098 TFS208 TBS038 3 x Oil Pressure Switches, check illustrations

200 Turbo 1982 1984 5 2.1L KG, KJ TFS103TFS104

2 x Thermo Fan Switches, check illustrations

200 Turbo 1986 1991 5 2.2L MC TPS021 TPS030

TFS103TFS104


5+5 1981 1984 5 2.1L WE TPS020 TFS102TFS135

2 x Thermo Fan Switches, check illustrations and Temp ranges

5E 1978 1982 5 2.1L WB, WC TFS102TFS135


A3 4D Hatchback 1997 2004 4 1.6L AEH TPS031TPS054

TTS504 TCS104TCS105

TFS190TFS198

TBS028TBS051

TRS045TRS048

For correct application, check illustrations and spec tables

A3 Attraction Hatchback 2004 on 4 1.6L BGU TPS054 TRS048

A3 4D Hatchback 1997 2004 4 1.8L AGN TPS031TPS054

TCS104TCS105

TFS190TFS198

TBS028TBS051

TRS045TRS048


A3 Turbo 4D Hatchback 1998 2004 4 1.8L AGU TPS031TPS054

TTS504 TCS104TCS105

TFS190TFS198


A3 2.0 TDI 2004 on 4 2.0L BKD TPS051 TCS111 TRS048

A3 3.2 Quattro 2004 on V6 3.2L BDB TPS053 TCS111 TRS048

A4 1.8 4D Sedan 08/1995 06/2001 4 1.8L ADR TPS031TPS054

TCS091TCS101TCS104TCS105

TFS103TFS208

TBS038TBS049

TRS004 For correct application, check illustrations and spec tables

Alfa Romeo, Audi

Audi cont.

Make and Model



WaterTemp

CoolantSensor

Fan Switch

Stop Light

Reverse Light

8

A4 1.8 Quattro 1995 1997 4 1.8L AGB TFS103TFS208


A4 1.8T (incl Quattro) 12/1995 1999 4 1.8L AEB TPS031 TCS101TCS105

TFS103TFS208

TBS038 2 x Coolant Sensors & 2 x Thermo Fan Swit-ches, check illustrations

A4 1.8T 1999 on 4 1.8L AJL TPS031TPS054

TCS104TCS105

TFS103TFS208

TBS038TBS049


A4 1.8T 4D Sedan 02/2002 on 4 1.8L AVJ TPS054 TCS104TCS111

2 x Coolant Sensors, check illustrations

A4 1.8T Cabriolet 2003 on 4 1.8L AVJ TCS104TCS111


A4 2.0 B6 07/2001 on 4 2.0L ALT TPS054 TCS104TCS111


A4 2.4 V6 (AGA) 1998 on V6 2.4L AGA TPS031 TCS105 TFS103TFS208

TBS038 2 x Thermo Fan Switches, check illustrations

A4 2.4 V6 (AFM) 02/1998 06/2001 V6 2.4L AFM TPS030TPS031

TFS103TFS208

TBS038 2 x Oil Pressure Switches & 2 Coolant Sensors, check illustrations

A4 2.6 V6 (ABC) 1995 1999 V6 2.6L ABC TPS030 TCS101TCS105

TFS103TFS208

TBS038TBS050


A4 2.6 Quattro 1995 1999 V6 2.6L ABC TPS030TPS031

TCS101TCS105

TFS103TFS208

TBS038TBS050


A4 2.8 Quattro 1995 1999 V6 2.8L ACK TPS030TPS031

TCS105 TFS103TFS208

TBS038 2 x Oil Pressure Switches & 2 Coolant Sensors, check illustrations

A4 3.0 V6 (incl Cab) 10/2001 on V6 3.0L ASN TPS054 TCS104TCS111

TRS030 2 x Coolant Sensors, Rev Light sw 5sp man only, check illustrations

A6 2.4 V6 (AGA) 1997 2004 V6 2.4L AGA TPS031TPS054

TCS104TCS105

TFS219 TBS038TBS049


A6 2.4 Quattro 1997 1999 V6 2.4L AGA TPS031TPS054

TCS104TCS105

TFS208 TBS038TBS049


A6 2.6 V6 (ABC) 1994 1997 V6 2.6L ABC TPS030TPS031TPS045TPS046

TCS098 TFS208 TBS038TBS049

4 x Oil Pressure Switches & 2 x Stop Light Switches, check illustrations

A6 2.6 Quattro 1994 1997 V6 2.6L ABC TPS030TPS031TPS045

TCS098 TFS208 TBS049 3 x Oil Pressure Switches, check illustrations

A6 2.7T Quattro 02/2002 on V6 2.7L AJK TPS031TPS054

TCS104TCS105

TFS219 TBS038TBS049


A6 2.8 V6 (ACK) 1997 1999 V6 2.8L ACK TPS030TPS031TPS045

TCS098 TFS103TFS208

TBS038TBS049


A6 2.8 Quattro 1997 2004 V6 2.8L ACK TPS031TPS054

TCS098 TFS103TFS208

TBS038TBS049


A6 3.0 Quattro 02/2002 10/2004 V6 3.0L BBJ TCS104 TFS219

A6 3.0 Quattro 11/2004 on V6 3.0L BBJ TPS054 TCS104

Audi cont.

9Vehicle Application List

Make and Model



WaterTemp

CoolantSensor

Fan Switch

Stop Light

Reverse Light

A6 Tdi FWD 2004 on V6 3.0L BMK TPS053 TCS111

A6 4.2 Quattro 04/2000 2004 V8 4.2L ABZ TFS219

A6 4.2 Quattro 2004 on V8 4.2L BAT TPS054 TCS111

A8 2.8 V6 05/1995 12/1996 V6 2.8L AAH TPS045TPS046

TCS105 TFS103TFS208

TBS038TBS049


A8 2.8 Quattro 01/1997 on V6 2.8L ACK TPS045TPS046

TCS105 TFS208 TBS049 TRS030 2 x Oil Pressure Switches, check illustrations

A8 3.7 V8 (AEW) 10/1996 1999 V8 3.7L AEW TPS030 TCS093 TFS205 TBS038TBS049


A8 4.2 Quattro 1995 2000 V8 4.2L ABZ TPS030TPS045

TCS093 TFS205 TBS049 TRS030 2 x Oil Pressure Switches, check illustrations

Allroad Quattro Tdi 4D Wagon 05/2002 on V6 2.5L AKE TPS053 TCS104 TFS219 TBS049 TRS030

Allroad Quattro 2.7 (incl Twin Turbo) 02/2001 on V6 2.7L AJK TPS031TPS054

TBS038 TBS049


Allroad Quattro 4.2 V8 4D Wagon 12/2003 on V8 4.2L BAS TPS054 TCS104 TBS049

S2 Turbo 1993 1996 5 2.2L AAN TFS103TFS208


S3 1.8T 1999 on 4 1.8L APY TPS054 TCS104TCS105

TFS190TFS198

TBS028TBS051

TRS045TRS048


S4 2.7 Twin Turbo 1999 2003 V6 2.7L ABG / AZB TCS104TCS105

TFS103TFS208


S6 4.2 V8 02/2001 on V8 4.2L AQJ TPS054 TBS038TBS049


S8 4.2 V8 1998 on V8 4.2L AHC, AHK TFS208

TT 1.8 (incl Turbo & Quat-tro)

1999 on 4 1.8L AJL,AJQ,APX

TPS054 TTS504 TCS104TCS105

TFS213 TBS051 TRS045TRS048


TT 3.2 Quattro 2004 on V6 3.2L BHE TPS054 TCS104 TFS218 TBS051 TRS048

V8 3.6 Quattro 1990 1992 V8 3.6L PTK TPS021 TCS093 TFS104 TBS038 TRS030 Reverse Light Switch for 6sp model only

BMW

316i E36 1995 1999 4 1.6L M43 B16 TPS039 TCS108 TFS107 TBS029TBS035

TRS034 2 x Stop Light Switches, check illustrations

316i E46 1999 2001 4 1.9L M43 B18 TPS039 TCS107 TFS107 TRS034

316ti E46 2001 on 4 1.8L N42 B18 TPS039 TCS107 TRS034

318i E21 (M10) 1980 1983 4 1.8L M10 TFS107

318i E30 1983 1987 4 1.8L M10 TTS035 TCS026 TFS107 TBS023TBS029


318i & 318iS E30 1988 1991 4 1.8L M40,M42 TPS039 TTS035 TCS040 TFS107 TBS029 TRS023 2 x Coolant Sensors, check illustrations

318i E36 1991 1994 4 1.8L M40 TPS039 TCS040TCS099

TFS107 TBS029TBS035

TRS023TRS034


318i E36 1994 1998 4 1.8L M43 TPS039 TCS040TCS099TCS108

TFS107 TBS029TBS035


Audi, BMW

Audi cont.

Make and Model



WaterTemp

CoolantSensor

Fan Switch

Stop Light

Reverse Light

10

318i E46 1998 on 4 1.9L M44 TCS108 TFS107

318iS E36 (Sedan M43) 1992 1998 4 1.8L M43 TFS201TFS217


318iS E36 (Coupe M42) 1993 1996 4 1.8L M42 B18 TPS039 TCS040TCS099

TFS107 TBS029 TRS034 2 x Coolant Sensors, check illustrations

318iS & 318Ti E36 (M44) 1996 on 4 1.9L M44 B19 TPS039 TCS108 TFS107 TBS029 TRS034

320 & 320i E21 (M10) 1976 1980 4 2.0L M10 TFS105TFS106


320i E30 (M20) 1988 1990 6 2.0L M20 TPS039 TTS035 TFS105TFS106

TBS029 TRS023 2 x Thermo Fan Switches, check illustrations

320i E36 (M50) 1991 1995 6 2.0L M50 TPS039 TTS035 TCS040TCS099

TFS107 TBS029TBS035

TRS023TRS034


320i E46 (M47) 06/2002 on 6 2.2L M47 TCS107

323i E30 (M20) 1982 1985 6 2.3L M20 B23 TPS026 TTS025TTS035

TBS023 TRS023 2 x Water Temp Senders, check illustrations

323i E36 (M52) 1996 1998 6 2.5L M52 TCS108 TFS217

323i & 323Ci E46 (M52) 1998 on 6 2.5L M52 B25 TPS039 TCS107 TFS217 TRS034

325i E30 (M20) 1988 1990 6 2.5L M20 B25 TPS039 TTS035 TCS040 TFS107 TBS023TBS029


325i E36 (M50) 1991 1995 6 2.5L M50 B25 TPS039 TTS035 TCS040TCS099

TFS107 TBS035 TRS023TRS034


325e E30 (M20) 1986 1987 6 2.7L M20 B27 TPS039 TTS035 TCS026 TFS105TFS106

TBS023TBS029

TRS023 2 x Stop Light Switches & 2 x Thermo Fan Switches, check illustrations and Temp ranges

325iS E30 (M20) 1988 1990 6 2.5L M20 TPS039 TTS035 TCS040 TFS105TFS106


325Ti E46 (M54) 05/2002 on 6 2.5L M54 TPS039 TRS034

325Ci E46 (M54) 2004 on 6 2.5L M54 TPS039 TCS107 TRS034

328i E36 (M52) 1995 2000 6 2.8L M52 B28 TPS039 TBS035 TRS034

328i E46 (M52) 1998 2000 6 2.8L M52 B28 TPS039 TCS107 TBS035 TRS034

328Ci E46 (M52) 1999 on 6 2.8L M52 B28 TPS039 TRS034

330i & 330Ci E36 (M54) 09/2000 on 6 3.0L M54 TPS039 TCS107 TRS034

520 E12 (M10) 1973 1978 4 2.0L M10 TFS107

520i E28 (M20) 1983 1985 6 2.0L M20 TPS026TPS039

TTS025TTS035

TCS026 TFS105TFS106

TBS023TBS029


520i E34 (M50) 1990 1996 6 2.0L M50 TPS039 TTS035 TCS040 TFS107 TRS023TRS034

2 x Coolant Sensors, & 2 x Reverse Light Switches check illustrations

523i E39 (M52) 1996 2000 6 2.5L M52 B25 TPS039 TCS108 TFS201TFS217

TRS034 2 x Thermo Fan Switches, check illustrations

525 i E34 (M20) 1988 1990 6 2.5L M20 B25 TPS039 TFS107 TBS035

525 i E34 (M50) 1990 1996 6 2.5L M50 TCS040TCS099

T

switches and sensors catalogue

Documents

oil pressure instrumentation

oil pressure values

tridon oil pressure

pressure rating

pressure increases

appropriate pressure

old oil

oil leaks