Oct 26 2004

Installation Procedure

FAX BoardSuper G3 FAX Board-Q1

ApplicationThis manual has been issued by Canon Inc. for qualified persons to learn technical theory, installation, maintenance, and

repair of products. This manual covers all localities where the products are sold. For this reason, there may be

information in this manual that does not apply to your locality.

CorrectionsThis manual may contain technical inaccuracies or typographical errors due to improvements or changes in products.

When changes occur in applicable products or in the contents of this manual, Canon will release technical information

as the need arises. In the event of major changes in the contents of this manual over a long or short period, Canon will

issue a new edition of this manual.

The following paragraph does not apply to any countries where such provisions are inconsistent with local law.

TrademarksThe product names and company names used in this manual are the registered trademarks of the individual companies.

CopyrightThis manual is copyrighted with all rights reserved. Under the copyright laws, this manual may not be copied,

reproduced or translated into another language, in whole or in part, without the written consent of Canon Inc.

COPYRIGHT © 2001 CANON INC.Printed in Japan

CautionUse of this manual should be strictly supervised to avoid disclosure of confidential information.

Introduction

Symbols Used

This documentation uses the following symbols to indicate special information:

Symbol Description

Indicates an item of a non-specific nature, possibly classified as Note, Caution, or Warning.

Indicates an item requiring care to avoid electric shocks.

Indicates an item requiring care to avoid combustion (fire).

Indicates an item prohibiting disassembly to avoid electric shocks or problems.

Indicates an item requiring disconnection of the power plug from the electric outlet.

Indicates an item intended to provide notes assisting the understanding of the topic in question.

Indicates an item of reference assisting the understanding of the topic in question.

Provides a description of a service mode.

Provides a description of the nature of an error indication.

Memo

REF.

Introduction

The following rules apply throughout this Service Manual:1. Each chapter contains sections explaining the purpose of specific functions and the relationship between electrical

and mechanical systems with reference to the timing of operation.

　In the diagrams, represents the path of mechanical drive; where a signal name accompanies the symbol ,

the arrow indicates the direction of the electric signal.

　The expression "turn on the power" means flipping on the power switch, closing the front door, and closing thedelivery unit door, which results in supplying the machine with power.

2. In the digital circuits, '1'is used to indicate that the voltage level of a given signal is "High", while '0' is used toindicate "Low".(The voltage value, however, differs from circuit to circuit.) In addition, the asterisk (*) as in"DRMD*" indicates that the DRMD signal goes on when '0'.

　In practically all cases, the internal mechanisms of a microprocessor cannot be checked in the field. Therefore, theoperations of the microprocessors used in the machines are not discussed: they are explained in terms of fromsensors to the input of the DC controller PCB and from the output of the DC controller PCB to the loads.

The descriptions in this Service Manual are subject to change without notice for product improvement or otherpurposes, and major changes will be communicated in the form of Service Information bulletins.All service persons are expected to have a good understanding of the contents of this Service Manual and all relevantService Information bulletins and be able to identify and isolate faults in the machine."

Contents

Contents

第 1 章　Installation Procedure

1.1 Making Pre-Checks ............................................................................................................................................... 21.1.1Checking Items in the Package ....................................................................................................................... 2

1.2 Installation Procedure............................................................................................................................................ 41.2.1Points to Note on Installation .......................................................................................................................... 41.2.2Making the Host Machine Ready for Installing the FAX Unit ....................................................................... 41.2.3Attaching the FAX Unit .................................................................................................................................. 71.2.4Connecting the FAX Cable ............................................................................................................................. 81.2.5Attaching the Modular Unit ............................................................................................................................ 91.2.6Connecting the Modular Cable........................................................................................................................ 91.2.7Attaching the FAX Power Cable................................................................................................................... 101.2.8Attaching the Speaker Unit ........................................................................................................................... 111.2.9After Attaching the FAX Unit....................................................................................................................... 11

1.3 Checking the Operation....................................................................................................................................... 131.3.1Type Settings ................................................................................................................................................. 131.3.2Basic Settings ................................................................................................................................................ 131.3.3Communication Test ..................................................................................................................................... 13

Contents

Chapter 1　Installation Procedure

Chapter 1　

2

1.1 Making Pre-Checks

1.1.1 Checking Items in the Package 0007-4430

F-1-1

T-1-1

[1] FAX Unit --- 1 pcs. [10] Cable Clip (large) --- 3 pcs.

[2] Modular Unit --- 1 pcs. [11] Cable Clip (small) --- 5 pcs.

[3] Speaker Unit --- 1 pcs. [12] SEND/FAX Guide --- 1 pcs.

[4] FAX Cable --- 1 pcs. [13] FAX Driver CD-ROM Unit --- 1 pcs.

[5] Modular Cable --- 1 pcs. [14] Super G3 Label (*2) --- 1 pcs.

[2] [3]

[7]

[8]

[6]

[5]

[4]

[9]

[1]

[12]

[13]

[15] - [17]

[10]

[11]

[14]

Chapter 1

3

Memo: The attachment position of the main units of this machine is shown in the following figure.

F-1-2

[1] FAX Unit[2] Modular Unit[3] Speaker Unit

[6] FAX Power Cable --- 1 pcs. [15] A-TICK Label (*3) --- 1 pcs.

[7] Speaker Connecting

Cable

---1 pcs.

[16] FAX certification Label

(*4)

---1 pcs.

[8] Modular Cord --- 1

pcs.(*

1)

[17] FCC Label (*2) --- 1 pcs.

[9] Screw (M3x8) --- 5 pcs.

*1: It is included 3 pieces concerning the products destined for Europe. Select the appropriate

modular cord conforming to each country/region from the multiple ones to use.

*2: It is included only with the products destined for North America.

*3: It is included only with the products destined for Australia.

*4: It is included only with the products destined for Europe. It is used in Germany only.

[1]

[2]

[3]

Chapter 1　

4

1.2 Installation Procedure

1.2.1 Points to Note onInstallation 0007-1178

Install the FAX unit after installation of the hostmachine is completed.

Be sure to perform the following steps in orderwith the host machine before installing the FAX unit.The hard disk drive may be broken if these steps areperformed in wrong order and the host machine shutsdown during an access to the hard disk drive as aresult.

1. Press the power switch on the control panel formore than 3 seconds.

2. Follow the shutdown sequence screen to operate thetouch panel so that the main power switch will beready for OFF.

3. Turn OFF the main power switch.4. Disconnect the power cable (for a wall outlet).

F-1-3

Be sure to use the modular cord found in thepackage. If you must use another modular cord, besure that it is no longer than 3m.

1.2.2 Making the HostMachine Ready forInstalling the FAX Unit 0007-4432

1) Remove the 14 screws [1], and detach the rearcover [2].

[4][3][2]

[1]

ON/OFF

Chapter 1

5

F-1-4

2) Remove the cassettes 1 and 2 [1], and detach the 4screws [2] to remove the left cover (lower) [3].

F-1-5

3) Remove the 2 screws [1], and detach the left cover(rear) [2].

F-1-6

4) Open the upper front cover [1].

F-1-7

5) Remove the blanking rubber [1], and detach thescrew [2] (binding screw: M4x8) and the screw [3](RS screw: M3x8); follow the directions in the fig.below to remove the front cover unit [4].

F-1-8

6) Remove the 4 screws [1], and detach the left cover[2].

[1] [1]

[1]

[1]

[1]

[1]

[1]

[1]

[1]

[1]

[1]

[1]

[1]

[1]

[2]

[2]

[2]

[1]

[3]

Chapter 1　

6

F-1-9

7) Follow the directions in the fig. below to removethe inside bottom cover [1].

F-1-10

8) Remove the left grip (front) [1] downward whilereleasing the 2 claws [2]; likewise, remove the leftgrip (rear) [3].

F-1-11

9) Attach the 2 cable clips (large) [1] and the 5 cableclips (small) [2] included in the package to the holeson the rear side plate of the host machine.

F-1-12

10) Remove the option power supply unit [1]temporarily to make the installation work easier.The steps for removing the option power supplyunit are as follows.

F-1-13

10-1) Detach the cables connected to the option powersupply unit [1] from the 3 cable clips [2], anddisconnect the 7 connectors [3].

F-1-14

10-2) Remove the 5 screws [1], and detach the option

[1]

[1]

[1]

[2]

Chapter 1

7

power supply unit [2].

F-1-15

1.2.3 Attaching the FAXUnit 0007-2717

1) Remove the protective packing [1] and the tapefrom the FAX unit.

F-1-16

2) Attach the cable clip (large) [1] included in thepackage to the hole of the FAX unit.

F-1-17

3) Insert the FAX unit [1] from under the left stay ofthe host machine, and connect the projections [A][B] to the inner slots [a] [b] of the host machine.

F-1-18

F-1-19

4) Fix the Fax unit with the 3 screws [1] included inthe package. (Using long screwdriver.)

Chapter 1　

8

F-1-20

Care should be taken so that the speaker cable [1]will not interfere with the edge (the diagonallyshaped area in the fig. below) of the left stay wheninserting the FAX unit.

F-1-21

1.2.4 Connecting the FAXCable 0007-2894

1) Connect the FAX cable [1] included in the packageto the 2 connectors [2] of the FAX unit.

F-1-22

2) Pass the FAX cable [1] through the 3 cable clips(large) [2] and then the edge cable clip [3].

F-1-23

3) Pass the FAX cable [1] through the 5 cable clips [2]and then the edge cable clip [3] under the controllerbox.

F-1-24

4) Connect the FAX cable to the connectors [1] [2] onthe main controller PCB.

Chapter 1

9

F-1-25

1.2.5 Attaching theModular Unit 0007-4433

1) Remove the 2 screws [1] on the side plate of thecontroller box, and detach the blanking plate [2];attach the modular unit [3] to the same positionusing the 2 screws [1] (used for fixing the blankingplate).

F-1-26

F-1-27

1.2.6 Connecting theModular Cable 0007-4434

1) Insert the modular cable [1] included in the packageinto the connector [2] of the FAX unit.

F-1-28

2) Pass the modular cable [1] through the 3 cable clips(small) [2] and the edge cable clip (upper) [3].

F-1-29

Memo: No need for fixing the reuse band [2] of themodular cable [1] to the sheet metal of the mainbody since the band is mounted in order to limitthe position movement of the core [3].

F-1-30

Chapter 1　

10

3) Connect the modular cable [1] to the connector [3]on the modular unit [2].

F-1-31

4) Pass the modular cable [1] through the 2 cable clips[2] and the edge cable clip [3], then pass it throughthe 3 cable clips [4] (at the bottom of the controllerbox).

F-1-32

F-1-33

Do not use the cable clip [1], which is mounted onthe supporting sheet metal of the modular board, tofix the modular cable [2]. If you do, the modularcable might be broken due to the load.

F-1-34

1.2.7 Attaching the FAXPower Cable 0007-2903

1) Connect the FAX power cable [1] included in thepackage to the connector [2] of the FAX unit.

F-1-35

2) Pass the FAX power cable [1] through the 2 cableclips (small) [2] and the edge cable clip (lower) [3].

F-1-36

3) Connect the FAX power cable [1] to the connector[2] on the controller power PCB.

Chapter 1

11

F-1-37

1.2.8 Attaching the SpeakerUnit 0007-2905

1) Connect the speaker connecting cable [2] to thespeaker unit [1]. Fit the speaker unit to emboss onthe front side plate, and attach it with the 2 screws[3].

F-1-38

2) Pass the speaker cable [1] through the 2 cable clips[2], and connect the speaker cable to the connector[3] of the FAX unit.

F-1-39

1.2.9 After Attaching theFAX Unit 0007-4428

1) Attach the following parts back to the hostmachine.

<Attaching Order>1. Option power supply unit2. Left grips (front and rear)3. Inside bottom cover4. Left cover5. Front cover unit6. Left cover (rear)7. Left cover (lower)8. Cassettes (1, 2)9. Rear cover

2) Connect one side of the modular cord included inthe package to the modular jack on a wall, and thenconnect the other side of the modular cord to themodular jack ("LINE 1") for line of the hostmachine.

3) Attach the various labels included in the package tothe specified position on the rear cover.

F-1-40

20mm

25mm

[1]

Chapter 1　

12

F-1-41

[1] Super G3 label- It is included only with the products destined forNorth America.[2] FCC label- It is included only with the products destined forNorth America.[3] A-TICK label- It is included only with the products destined forAustralia.[4] Fax certification label- It is included only with the products destined forEurope. It is used in Germany only.

4) Connect the power plug of the host machine to areceptacle, and turn ON the main power switch.

Chapter 1

13

1.3 Checking the Operation

1.3.1 Type Settings 0007-2908

Make country/region settings of the FAX board in service mode (FAX>Type>TYPE).With the settings, parameter will be set to meet the communication standards for each country/region.

1.3.2 Basic Settings 0007-2909

In this section, make only minimum settings required for FAX communication.

- User Phone NumberAdditional Function Key > [Communications Settings] > [User Settings] > [Unit Telephone #] > Enter fax number > [OK]- Telephone Line TypeAdditional Function Key > [Communications Settings] > [User Settings] > [Tel Line Type] > Select a type of line connection > [OK]

1.3.3 Communication Test 0007-2910

Perform a communication test to see if the Fax functions properly work.

1) Use the on-hook dial function to check dial tone. If there is no dial tone, check to make sure that the modular cordis properly connected to the modular jack on the wall/machine.

2) If there is dial tone, enter any phone service number (such as time signal) with the numeric keys to see if the servicestarts properly. If the service fails to be started, make sure that the line type specified in user mode and the linetype connected to the machine match.

3) Enter phone number of a destination available for the communication test with the numeric keys, and send a testdocument; make sure that the document is properly sent.

4) Send a test document from the other machine of the communication test, and make sure that the machine properlyreceives the document.

Oct 26 2004