subpart o - machine guarding · 2014-05-12 · the cutting heads of each wood shaper, hand-fed...
TRANSCRIPT
![Page 1: Subpart O - Machine Guarding · 2014-05-12 · The cutting heads of each wood shaper, hand-fed panel raiser, or other similar machine not automatically fed, shall be enclosed with](https://reader034.vdocuments.site/reader034/viewer/2022042108/5e8883443b9a605f2857ba12/html5/thumbnails/1.jpg)
1
Subpart O - Machine Guarding
OTI 501 Paul A. Schlumper, PE, CSP
![Page 2: Subpart O - Machine Guarding · 2014-05-12 · The cutting heads of each wood shaper, hand-fed panel raiser, or other similar machine not automatically fed, shall be enclosed with](https://reader034.vdocuments.site/reader034/viewer/2022042108/5e8883443b9a605f2857ba12/html5/thumbnails/2.jpg)
2
We Will Cover:
Machine Guarding PrinciplesSubpart O - HighlightsMock Plant Walk-Through
![Page 3: Subpart O - Machine Guarding · 2014-05-12 · The cutting heads of each wood shaper, hand-fed panel raiser, or other similar machine not automatically fed, shall be enclosed with](https://reader034.vdocuments.site/reader034/viewer/2022042108/5e8883443b9a605f2857ba12/html5/thumbnails/3.jpg)
3
Why are machines not guarded?
No one would stick their arm, hand, finger, head, etc. in there.No one is supposed to be back there, in there, around it while it is running.The machine came that way; it never had a guard.I’ve been doing it this way for twenty years without any problems.
![Page 4: Subpart O - Machine Guarding · 2014-05-12 · The cutting heads of each wood shaper, hand-fed panel raiser, or other similar machine not automatically fed, shall be enclosed with](https://reader034.vdocuments.site/reader034/viewer/2022042108/5e8883443b9a605f2857ba12/html5/thumbnails/4.jpg)
4
Why are machines not guarded? (cont.)
The guard is in the wayThe OSHA inspector didn’t say anything about it.We’ll put it back on if OSHA comes.
![Page 5: Subpart O - Machine Guarding · 2014-05-12 · The cutting heads of each wood shaper, hand-fed panel raiser, or other similar machine not automatically fed, shall be enclosed with](https://reader034.vdocuments.site/reader034/viewer/2022042108/5e8883443b9a605f2857ba12/html5/thumbnails/5.jpg)
5
Machine Guarding Requirements
Prevent contactBe secureProtect from falling objectsCreate no new hazardsNo interferenceMaintainability and accessibility
![Page 6: Subpart O - Machine Guarding · 2014-05-12 · The cutting heads of each wood shaper, hand-fed panel raiser, or other similar machine not automatically fed, shall be enclosed with](https://reader034.vdocuments.site/reader034/viewer/2022042108/5e8883443b9a605f2857ba12/html5/thumbnails/6.jpg)
6
Where machine hazards occur:
Point of operationMechanical power transmissionOther moving parts
![Page 7: Subpart O - Machine Guarding · 2014-05-12 · The cutting heads of each wood shaper, hand-fed panel raiser, or other similar machine not automatically fed, shall be enclosed with](https://reader034.vdocuments.site/reader034/viewer/2022042108/5e8883443b9a605f2857ba12/html5/thumbnails/7.jpg)
7
Methods of machine safeguarding
Physical guardsDevicesLocation/Distance
![Page 8: Subpart O - Machine Guarding · 2014-05-12 · The cutting heads of each wood shaper, hand-fed panel raiser, or other similar machine not automatically fed, shall be enclosed with](https://reader034.vdocuments.site/reader034/viewer/2022042108/5e8883443b9a605f2857ba12/html5/thumbnails/8.jpg)
8
Guards
FixedInterlockedAdjustableSelf-adjusting
![Page 9: Subpart O - Machine Guarding · 2014-05-12 · The cutting heads of each wood shaper, hand-fed panel raiser, or other similar machine not automatically fed, shall be enclosed with](https://reader034.vdocuments.site/reader034/viewer/2022042108/5e8883443b9a605f2857ba12/html5/thumbnails/9.jpg)
9
Safeguarding devices
Presence sensingPullbackRestraintSafety controls and tripsGates
![Page 10: Subpart O - Machine Guarding · 2014-05-12 · The cutting heads of each wood shaper, hand-fed panel raiser, or other similar machine not automatically fed, shall be enclosed with](https://reader034.vdocuments.site/reader034/viewer/2022042108/5e8883443b9a605f2857ba12/html5/thumbnails/10.jpg)
10
Subpart O - Machinery and Machine Guarding
211 - Definitions212 - General requirements213 - Woodworking machinery 215 - Abrasive wheel machinery216 - Mills and calendars217 - Mechanical power presses218 - Forging machines219 - Mechanical power transmission
![Page 11: Subpart O - Machine Guarding · 2014-05-12 · The cutting heads of each wood shaper, hand-fed panel raiser, or other similar machine not automatically fed, shall be enclosed with](https://reader034.vdocuments.site/reader034/viewer/2022042108/5e8883443b9a605f2857ba12/html5/thumbnails/11.jpg)
11
1910.212
General Requirements for all Machines
![Page 12: Subpart O - Machine Guarding · 2014-05-12 · The cutting heads of each wood shaper, hand-fed panel raiser, or other similar machine not automatically fed, shall be enclosed with](https://reader034.vdocuments.site/reader034/viewer/2022042108/5e8883443b9a605f2857ba12/html5/thumbnails/12.jpg)
12
1910.212(a)(1)
One or more methods of machine guarding shall be provided to protect the operator and other employees in the machine area from hazards such as those created by the point of operation, in-going nip points, rotating parts, flying chips and sparks.
![Page 13: Subpart O - Machine Guarding · 2014-05-12 · The cutting heads of each wood shaper, hand-fed panel raiser, or other similar machine not automatically fed, shall be enclosed with](https://reader034.vdocuments.site/reader034/viewer/2022042108/5e8883443b9a605f2857ba12/html5/thumbnails/13.jpg)
13
1910.212(a)(2)
The guard shall be such that it does not offer an accident hazard in itself
![Page 14: Subpart O - Machine Guarding · 2014-05-12 · The cutting heads of each wood shaper, hand-fed panel raiser, or other similar machine not automatically fed, shall be enclosed with](https://reader034.vdocuments.site/reader034/viewer/2022042108/5e8883443b9a605f2857ba12/html5/thumbnails/14.jpg)
14
1910.212(a)(3)(ii)
The point of operation of machines whose operation exposes an employee to injury, shall be guarded
![Page 15: Subpart O - Machine Guarding · 2014-05-12 · The cutting heads of each wood shaper, hand-fed panel raiser, or other similar machine not automatically fed, shall be enclosed with](https://reader034.vdocuments.site/reader034/viewer/2022042108/5e8883443b9a605f2857ba12/html5/thumbnails/15.jpg)
15
1910.212(a)(3)(iii)
Special hand tools for placing and removing material shall be such as to permit easy handling of material in the danger zone. Such tools shall not be in lieu of other guarding required by this section, but can only be used to supplement protection provided.
![Page 16: Subpart O - Machine Guarding · 2014-05-12 · The cutting heads of each wood shaper, hand-fed panel raiser, or other similar machine not automatically fed, shall be enclosed with](https://reader034.vdocuments.site/reader034/viewer/2022042108/5e8883443b9a605f2857ba12/html5/thumbnails/16.jpg)
16
1910.212(a)(3)(iv)Usually require guarding:
Guillotine cuttersShears (including alligator shears)Power pressesMilling machinesPower sawsJointersPortable power toolsForming rolls and calendars
![Page 17: Subpart O - Machine Guarding · 2014-05-12 · The cutting heads of each wood shaper, hand-fed panel raiser, or other similar machine not automatically fed, shall be enclosed with](https://reader034.vdocuments.site/reader034/viewer/2022042108/5e8883443b9a605f2857ba12/html5/thumbnails/17.jpg)
17
1910.212(a)(5)
When the periphery of the blades of a fan is less than seven (7) feet above the floor or working level, the blades shall be guarded. The guard shall have openings no larger than 1/2 inch.
![Page 18: Subpart O - Machine Guarding · 2014-05-12 · The cutting heads of each wood shaper, hand-fed panel raiser, or other similar machine not automatically fed, shall be enclosed with](https://reader034.vdocuments.site/reader034/viewer/2022042108/5e8883443b9a605f2857ba12/html5/thumbnails/18.jpg)
18
1910.212(b)
Machines designed for a fixed location shall be securely anchored to prevent walking or moving.
![Page 19: Subpart O - Machine Guarding · 2014-05-12 · The cutting heads of each wood shaper, hand-fed panel raiser, or other similar machine not automatically fed, shall be enclosed with](https://reader034.vdocuments.site/reader034/viewer/2022042108/5e8883443b9a605f2857ba12/html5/thumbnails/19.jpg)
19
1910.213
Woodworking Machinery Requirements
![Page 20: Subpart O - Machine Guarding · 2014-05-12 · The cutting heads of each wood shaper, hand-fed panel raiser, or other similar machine not automatically fed, shall be enclosed with](https://reader034.vdocuments.site/reader034/viewer/2022042108/5e8883443b9a605f2857ba12/html5/thumbnails/20.jpg)
20
1910.213(a)(9)
All belts, pulleys, gears, shafts, and moving parts shall be guarded in accordance with the specific requirements of 1910.219.
![Page 21: Subpart O - Machine Guarding · 2014-05-12 · The cutting heads of each wood shaper, hand-fed panel raiser, or other similar machine not automatically fed, shall be enclosed with](https://reader034.vdocuments.site/reader034/viewer/2022042108/5e8883443b9a605f2857ba12/html5/thumbnails/21.jpg)
21
1910.213(a)(10)
It is recommended that each power-driven woodworking machine be provided with a disconnect switch that can be locked in the off position.
![Page 22: Subpart O - Machine Guarding · 2014-05-12 · The cutting heads of each wood shaper, hand-fed panel raiser, or other similar machine not automatically fed, shall be enclosed with](https://reader034.vdocuments.site/reader034/viewer/2022042108/5e8883443b9a605f2857ba12/html5/thumbnails/22.jpg)
22
1910.213(a)(15)
Combs (featherboards) or suitable jigs shall be provided at the workplace for use when a standard guard cannot be used.
![Page 23: Subpart O - Machine Guarding · 2014-05-12 · The cutting heads of each wood shaper, hand-fed panel raiser, or other similar machine not automatically fed, shall be enclosed with](https://reader034.vdocuments.site/reader034/viewer/2022042108/5e8883443b9a605f2857ba12/html5/thumbnails/23.jpg)
23
1910.213(b)(1)
A mechanical or electrical power control shall be provided on each machine to make it possible for the operator to cut off the power from each machine without leaving his position at the point of operation.
![Page 24: Subpart O - Machine Guarding · 2014-05-12 · The cutting heads of each wood shaper, hand-fed panel raiser, or other similar machine not automatically fed, shall be enclosed with](https://reader034.vdocuments.site/reader034/viewer/2022042108/5e8883443b9a605f2857ba12/html5/thumbnails/24.jpg)
24
1910.213(b)(3)
On applications where injury to the operator might result if motors were to restart after power failures, provision shall be made to prevent machines from automatically restarting upon restoration of power.
![Page 25: Subpart O - Machine Guarding · 2014-05-12 · The cutting heads of each wood shaper, hand-fed panel raiser, or other similar machine not automatically fed, shall be enclosed with](https://reader034.vdocuments.site/reader034/viewer/2022042108/5e8883443b9a605f2857ba12/html5/thumbnails/25.jpg)
25
1910.213(c)(1)Each circular hand-fed ripsaw shall be guarded by a hood which shall completely enclose that portion of the saw above the table and that portion of the saw above the material being cut. The hood and mounting shall be arranged so that the hood will automatically adjust itself to the thickness of and remain in contact with the material being cut without considerable resistance.
![Page 26: Subpart O - Machine Guarding · 2014-05-12 · The cutting heads of each wood shaper, hand-fed panel raiser, or other similar machine not automatically fed, shall be enclosed with](https://reader034.vdocuments.site/reader034/viewer/2022042108/5e8883443b9a605f2857ba12/html5/thumbnails/26.jpg)
26
1910.213(c)(2)
Each hand-fed circular ripsaw shall be furnished with a spreader to prevent material from squeezing the saw or being thrown back on the operator.
![Page 27: Subpart O - Machine Guarding · 2014-05-12 · The cutting heads of each wood shaper, hand-fed panel raiser, or other similar machine not automatically fed, shall be enclosed with](https://reader034.vdocuments.site/reader034/viewer/2022042108/5e8883443b9a605f2857ba12/html5/thumbnails/27.jpg)
27
1910.213(c)(3)
Each hand-fed circular ripsaw shall be provided with non-kickback fingers or dogs so located as to oppose the thrust or tendency of the saw to pick up the material or throw it back toward the operator.
![Page 28: Subpart O - Machine Guarding · 2014-05-12 · The cutting heads of each wood shaper, hand-fed panel raiser, or other similar machine not automatically fed, shall be enclosed with](https://reader034.vdocuments.site/reader034/viewer/2022042108/5e8883443b9a605f2857ba12/html5/thumbnails/28.jpg)
28
1910.213(d)(1)
Each circular crosscut table saw shall be guarded by a hood which shall meet all the requirements of 1910.213(c)(1) for hoods for circular resaws.
![Page 29: Subpart O - Machine Guarding · 2014-05-12 · The cutting heads of each wood shaper, hand-fed panel raiser, or other similar machine not automatically fed, shall be enclosed with](https://reader034.vdocuments.site/reader034/viewer/2022042108/5e8883443b9a605f2857ba12/html5/thumbnails/29.jpg)
29
1910.213(h)(1)
The upper hood shall completely enclose the upper portion of the blade down to a point that will include the end of the saw arbor… The sides of the lower exposed portion of the blade shall be guarded to the full diameter of the blade by a device that will automatically adjust itself of the thickness of the stock and remain in contact with the stock.
![Page 30: Subpart O - Machine Guarding · 2014-05-12 · The cutting heads of each wood shaper, hand-fed panel raiser, or other similar machine not automatically fed, shall be enclosed with](https://reader034.vdocuments.site/reader034/viewer/2022042108/5e8883443b9a605f2857ba12/html5/thumbnails/30.jpg)
30
1910.213(h)(2)
Each radial saw used for ripping shall be provided with non kickback fingers or dogs located on both sides of the saw...
![Page 31: Subpart O - Machine Guarding · 2014-05-12 · The cutting heads of each wood shaper, hand-fed panel raiser, or other similar machine not automatically fed, shall be enclosed with](https://reader034.vdocuments.site/reader034/viewer/2022042108/5e8883443b9a605f2857ba12/html5/thumbnails/31.jpg)
31
1910.213(h)(3)
An adjustable stop shall be provided to prevent the forward travel of the blade beyond the position necessary to complete the cut in repetitive operations.
![Page 32: Subpart O - Machine Guarding · 2014-05-12 · The cutting heads of each wood shaper, hand-fed panel raiser, or other similar machine not automatically fed, shall be enclosed with](https://reader034.vdocuments.site/reader034/viewer/2022042108/5e8883443b9a605f2857ba12/html5/thumbnails/32.jpg)
32
1910.213(h)(4)
Installation shall be in such a manner that the front end of the unit will be slightly higher than the rear, so as to cause the cutting head to return gently to the starting position when released by the operator.
![Page 33: Subpart O - Machine Guarding · 2014-05-12 · The cutting heads of each wood shaper, hand-fed panel raiser, or other similar machine not automatically fed, shall be enclosed with](https://reader034.vdocuments.site/reader034/viewer/2022042108/5e8883443b9a605f2857ba12/html5/thumbnails/33.jpg)
33
1910.213(h)(5)
Ripping and ploughing shall be against the direction in which the saw turns. The direction of the saw rotation shall be conspicuously marked on the hood.
![Page 34: Subpart O - Machine Guarding · 2014-05-12 · The cutting heads of each wood shaper, hand-fed panel raiser, or other similar machine not automatically fed, shall be enclosed with](https://reader034.vdocuments.site/reader034/viewer/2022042108/5e8883443b9a605f2857ba12/html5/thumbnails/34.jpg)
34
1910.213(i)(1)
All portions of the saw blade (bandsaws) shall be enclosed or guarded, except for the working portion of the blade between the bottom of the guide rolls and the table.
![Page 35: Subpart O - Machine Guarding · 2014-05-12 · The cutting heads of each wood shaper, hand-fed panel raiser, or other similar machine not automatically fed, shall be enclosed with](https://reader034.vdocuments.site/reader034/viewer/2022042108/5e8883443b9a605f2857ba12/html5/thumbnails/35.jpg)
35
1910.213(j)(3)
Each hand-fed jointer with a horizontal cutting head shall have an automatic guard which will cover all the section of the head on the working side of the fence or gage.
![Page 36: Subpart O - Machine Guarding · 2014-05-12 · The cutting heads of each wood shaper, hand-fed panel raiser, or other similar machine not automatically fed, shall be enclosed with](https://reader034.vdocuments.site/reader034/viewer/2022042108/5e8883443b9a605f2857ba12/html5/thumbnails/36.jpg)
36
1910.213(j)(4)
Each hand-fed jointer with horizontal cutting head shall have a guard which will cover the section of the head back of the gage or fence.
![Page 37: Subpart O - Machine Guarding · 2014-05-12 · The cutting heads of each wood shaper, hand-fed panel raiser, or other similar machine not automatically fed, shall be enclosed with](https://reader034.vdocuments.site/reader034/viewer/2022042108/5e8883443b9a605f2857ba12/html5/thumbnails/37.jpg)
37
1910.213(m)(1)
The cutting heads of each wood shaper, hand-fed panel raiser, or other similar machine not automatically fed, shall be enclosed with a cage or adjustable guard so designed as to keep the operator’s hand away from the cutting edge.
![Page 38: Subpart O - Machine Guarding · 2014-05-12 · The cutting heads of each wood shaper, hand-fed panel raiser, or other similar machine not automatically fed, shall be enclosed with](https://reader034.vdocuments.site/reader034/viewer/2022042108/5e8883443b9a605f2857ba12/html5/thumbnails/38.jpg)
38
1910.213(o)(2)
Cutting heads on wood-turning lathes, whether rotating or not, shall be covered as completely as possible by hoods or shields.
![Page 39: Subpart O - Machine Guarding · 2014-05-12 · The cutting heads of each wood shaper, hand-fed panel raiser, or other similar machine not automatically fed, shall be enclosed with](https://reader034.vdocuments.site/reader034/viewer/2022042108/5e8883443b9a605f2857ba12/html5/thumbnails/39.jpg)
39
1910.213(p)(4)
Belt sanding machines shall be provided with guards at each nip point where the sanding belt runs on to the pulley.... The unused run of the sanding belt shall be guarded against accidental contact.
![Page 40: Subpart O - Machine Guarding · 2014-05-12 · The cutting heads of each wood shaper, hand-fed panel raiser, or other similar machine not automatically fed, shall be enclosed with](https://reader034.vdocuments.site/reader034/viewer/2022042108/5e8883443b9a605f2857ba12/html5/thumbnails/40.jpg)
40
1910.213(r)(4)
The mention of specific machines in paragraphs (a) thru (q) and this paragraph (r) of this section, inclusive, is not intended to exclude other woodworking machines from the requirements that suitable guards and exhaust hoods be provided to reduce to a minimum the hazard due to the point of operation of such machines.
![Page 41: Subpart O - Machine Guarding · 2014-05-12 · The cutting heads of each wood shaper, hand-fed panel raiser, or other similar machine not automatically fed, shall be enclosed with](https://reader034.vdocuments.site/reader034/viewer/2022042108/5e8883443b9a605f2857ba12/html5/thumbnails/41.jpg)
41
1910.213(s)(2)
All knives and cutting heads of woodworking machines shall be kept sharp, properly adjusted, and firmly secured. Where two or more knives are used, they shall be properly balanced.
![Page 42: Subpart O - Machine Guarding · 2014-05-12 · The cutting heads of each wood shaper, hand-fed panel raiser, or other similar machine not automatically fed, shall be enclosed with](https://reader034.vdocuments.site/reader034/viewer/2022042108/5e8883443b9a605f2857ba12/html5/thumbnails/42.jpg)
42
1910.213(s)(7)
All cracked saws shall be removed from service.
![Page 43: Subpart O - Machine Guarding · 2014-05-12 · The cutting heads of each wood shaper, hand-fed panel raiser, or other similar machine not automatically fed, shall be enclosed with](https://reader034.vdocuments.site/reader034/viewer/2022042108/5e8883443b9a605f2857ba12/html5/thumbnails/43.jpg)
43
1910.215
Abrasive-Wheel Machinery
![Page 44: Subpart O - Machine Guarding · 2014-05-12 · The cutting heads of each wood shaper, hand-fed panel raiser, or other similar machine not automatically fed, shall be enclosed with](https://reader034.vdocuments.site/reader034/viewer/2022042108/5e8883443b9a605f2857ba12/html5/thumbnails/44.jpg)
44
1910.215(a)(4)
Work rests shall be adjusted closely to the wheel with a maximum opening of one-eighth inch to prevent the work from being jammed between the wheel and the rest, which may cause wheel breakage.
![Page 45: Subpart O - Machine Guarding · 2014-05-12 · The cutting heads of each wood shaper, hand-fed panel raiser, or other similar machine not automatically fed, shall be enclosed with](https://reader034.vdocuments.site/reader034/viewer/2022042108/5e8883443b9a605f2857ba12/html5/thumbnails/45.jpg)
45
1910.215(b)(9)
The distance between the wheel periphery and the adjustable tongue or the end of the peripheral member at the top shall never exceed one-fourth inch.
![Page 46: Subpart O - Machine Guarding · 2014-05-12 · The cutting heads of each wood shaper, hand-fed panel raiser, or other similar machine not automatically fed, shall be enclosed with](https://reader034.vdocuments.site/reader034/viewer/2022042108/5e8883443b9a605f2857ba12/html5/thumbnails/46.jpg)
46
1910.215(d)(1)
Immediately before mounting, all wheels shall be closely inspected and sounded by the user (ring test) to make sure they have not been damaged.
![Page 47: Subpart O - Machine Guarding · 2014-05-12 · The cutting heads of each wood shaper, hand-fed panel raiser, or other similar machine not automatically fed, shall be enclosed with](https://reader034.vdocuments.site/reader034/viewer/2022042108/5e8883443b9a605f2857ba12/html5/thumbnails/47.jpg)
47
1910.216
Mills and Calendars in the Rubber and Plastics Industries
![Page 48: Subpart O - Machine Guarding · 2014-05-12 · The cutting heads of each wood shaper, hand-fed panel raiser, or other similar machine not automatically fed, shall be enclosed with](https://reader034.vdocuments.site/reader034/viewer/2022042108/5e8883443b9a605f2857ba12/html5/thumbnails/48.jpg)
48
1910.216(b)
A safety trip control must be provided in front and back of each mill. It must be accessible and operate readily on contact. It must be one of the following:
Pressure-sensitive body barSafety triprodSafety tripwire cable or wire
![Page 49: Subpart O - Machine Guarding · 2014-05-12 · The cutting heads of each wood shaper, hand-fed panel raiser, or other similar machine not automatically fed, shall be enclosed with](https://reader034.vdocuments.site/reader034/viewer/2022042108/5e8883443b9a605f2857ba12/html5/thumbnails/49.jpg)
49
1910.216(c)
A safety triprod, cable or wire must be provided across each pair or in-running rolls extending the length of the face of the rolls. It must be readily accessible and operate whether pushed or pulled.On both sides of the calendar and near each end of the face of the roll, there must be a safety trip cable or wire.
![Page 50: Subpart O - Machine Guarding · 2014-05-12 · The cutting heads of each wood shaper, hand-fed panel raiser, or other similar machine not automatically fed, shall be enclosed with](https://reader034.vdocuments.site/reader034/viewer/2022042108/5e8883443b9a605f2857ba12/html5/thumbnails/50.jpg)
50
1910.216(f)
Mills must stop within 1 1/2 percent of the peripheral no-load surface speed in feet per minute.Calendars must stop within 1 3/4 percent of the peripheral no-load surface speed in feet per minute. There is an exception for speeds above 250 feet per minute.
![Page 51: Subpart O - Machine Guarding · 2014-05-12 · The cutting heads of each wood shaper, hand-fed panel raiser, or other similar machine not automatically fed, shall be enclosed with](https://reader034.vdocuments.site/reader034/viewer/2022042108/5e8883443b9a605f2857ba12/html5/thumbnails/51.jpg)
51
1910.217
Mechanical Power Presses
![Page 52: Subpart O - Machine Guarding · 2014-05-12 · The cutting heads of each wood shaper, hand-fed panel raiser, or other similar machine not automatically fed, shall be enclosed with](https://reader034.vdocuments.site/reader034/viewer/2022042108/5e8883443b9a605f2857ba12/html5/thumbnails/52.jpg)
52
1910.217(a)(5)
Press brakes, hydraulic and pneumatic power presses, bulldozers, hot bending and hot metal presses, forging presses and hammers, riveting machines and similar types of fastener applicators are excluded from the requirements of this section.
![Page 53: Subpart O - Machine Guarding · 2014-05-12 · The cutting heads of each wood shaper, hand-fed panel raiser, or other similar machine not automatically fed, shall be enclosed with](https://reader034.vdocuments.site/reader034/viewer/2022042108/5e8883443b9a605f2857ba12/html5/thumbnails/53.jpg)
53
1910.217(b)(3)(i)
Machines using full revolution clutches shall incorporate a single-stroke mechanism.
![Page 54: Subpart O - Machine Guarding · 2014-05-12 · The cutting heads of each wood shaper, hand-fed panel raiser, or other similar machine not automatically fed, shall be enclosed with](https://reader034.vdocuments.site/reader034/viewer/2022042108/5e8883443b9a605f2857ba12/html5/thumbnails/54.jpg)
54
1910.217(b)(4)
The pedal mechanism shall be protected to prevent unintended operation.A pad with a nonslip contact area shall be firmly attached to the pedal.
![Page 55: Subpart O - Machine Guarding · 2014-05-12 · The cutting heads of each wood shaper, hand-fed panel raiser, or other similar machine not automatically fed, shall be enclosed with](https://reader034.vdocuments.site/reader034/viewer/2022042108/5e8883443b9a605f2857ba12/html5/thumbnails/55.jpg)
55
1910.217(b)(6)A two-hand trip shall have the individual operator’s hand controls protected against unintended operation and be arranged to require use of both hands.Two-hand trip systems on full revolution clutch machines shall incorporate an antirepeatfeature.If two hand trip systems are used on multiple operator systems, each operator shall have a separate set of controls.
![Page 56: Subpart O - Machine Guarding · 2014-05-12 · The cutting heads of each wood shaper, hand-fed panel raiser, or other similar machine not automatically fed, shall be enclosed with](https://reader034.vdocuments.site/reader034/viewer/2022042108/5e8883443b9a605f2857ba12/html5/thumbnails/56.jpg)
56
1910.217(b)(7)
Two-hand controls must incorporate an anti repeat feature, require use of both hands, be protected against unintended operation, have one set of controls for each operator.If foot control is provided, the selection between hand and foot control must be supervised by the employer.
![Page 57: Subpart O - Machine Guarding · 2014-05-12 · The cutting heads of each wood shaper, hand-fed panel raiser, or other similar machine not automatically fed, shall be enclosed with](https://reader034.vdocuments.site/reader034/viewer/2022042108/5e8883443b9a605f2857ba12/html5/thumbnails/57.jpg)
57
1910.217(b)(8)(i)
A main power disconnect switch, capable of being locked only in the off position shall be provided with every power press control system.
![Page 58: Subpart O - Machine Guarding · 2014-05-12 · The cutting heads of each wood shaper, hand-fed panel raiser, or other similar machine not automatically fed, shall be enclosed with](https://reader034.vdocuments.site/reader034/viewer/2022042108/5e8883443b9a605f2857ba12/html5/thumbnails/58.jpg)
58
1910.217(b)(13)
When required by paragraph (c)(5), the control system shall be constructed so that a failure within the system does not prevent the normal stopping action but does prevent initiation of a successive stroke until the failure is corrected.
![Page 59: Subpart O - Machine Guarding · 2014-05-12 · The cutting heads of each wood shaper, hand-fed panel raiser, or other similar machine not automatically fed, shall be enclosed with](https://reader034.vdocuments.site/reader034/viewer/2022042108/5e8883443b9a605f2857ba12/html5/thumbnails/59.jpg)
59
190.217(b)(14)
When required by paragraph (c)(5), brake monitors must be constructed as to automatically prevent the activation of a successive stroke if the stopping time or braking distance deteriorates to a point where the safety distance requirements are not met.
![Page 60: Subpart O - Machine Guarding · 2014-05-12 · The cutting heads of each wood shaper, hand-fed panel raiser, or other similar machine not automatically fed, shall be enclosed with](https://reader034.vdocuments.site/reader034/viewer/2022042108/5e8883443b9a605f2857ba12/html5/thumbnails/60.jpg)
60
1910.217(c)(1)
It shall be the responsibility of the employer to provide and insure the use of point of operation guards or properly applied and adjusted point of operation devices on every operation performed on a mechanical power press. See Table O-10.
![Page 61: Subpart O - Machine Guarding · 2014-05-12 · The cutting heads of each wood shaper, hand-fed panel raiser, or other similar machine not automatically fed, shall be enclosed with](https://reader034.vdocuments.site/reader034/viewer/2022042108/5e8883443b9a605f2857ba12/html5/thumbnails/61.jpg)
61
1910.217
Safety distance will be greater than the distance determined by the following formula:
Ds = 63 inches/second X Ts where Ts is the stopping time of the press measured at approximately 90 degree position of crankshaft rotation (seconds)
![Page 62: Subpart O - Machine Guarding · 2014-05-12 · The cutting heads of each wood shaper, hand-fed panel raiser, or other similar machine not automatically fed, shall be enclosed with](https://reader034.vdocuments.site/reader034/viewer/2022042108/5e8883443b9a605f2857ba12/html5/thumbnails/62.jpg)
62
1910.21(e)(1)
It shall be the responsibility of the employer to establish and follow a program of periodic and regular inspections of power presses.
![Page 63: Subpart O - Machine Guarding · 2014-05-12 · The cutting heads of each wood shaper, hand-fed panel raiser, or other similar machine not automatically fed, shall be enclosed with](https://reader034.vdocuments.site/reader034/viewer/2022042108/5e8883443b9a605f2857ba12/html5/thumbnails/63.jpg)
63
1910.217(e)(3)
It shall be the responsibility of the employer to insure the original and continuing competence of personnel caring for, inspecting, and maintaining power presses.
![Page 64: Subpart O - Machine Guarding · 2014-05-12 · The cutting heads of each wood shaper, hand-fed panel raiser, or other similar machine not automatically fed, shall be enclosed with](https://reader034.vdocuments.site/reader034/viewer/2022042108/5e8883443b9a605f2857ba12/html5/thumbnails/64.jpg)
64
1910.217(f)
The employer shall train and instruct the operator in the safe method of work before starting work on any operation covered by this section. The employer shall provide clearance between machines. Ample room for cleaning machines, handling material, work pieces, and scrap shall also be provided.
![Page 65: Subpart O - Machine Guarding · 2014-05-12 · The cutting heads of each wood shaper, hand-fed panel raiser, or other similar machine not automatically fed, shall be enclosed with](https://reader034.vdocuments.site/reader034/viewer/2022042108/5e8883443b9a605f2857ba12/html5/thumbnails/65.jpg)
65
1910.217(g)(1)
The employer shall, within 30 days, report all point of operation injuries to operators or other employees.
![Page 66: Subpart O - Machine Guarding · 2014-05-12 · The cutting heads of each wood shaper, hand-fed panel raiser, or other similar machine not automatically fed, shall be enclosed with](https://reader034.vdocuments.site/reader034/viewer/2022042108/5e8883443b9a605f2857ba12/html5/thumbnails/66.jpg)
66
1910.218
Forging Machines
![Page 67: Subpart O - Machine Guarding · 2014-05-12 · The cutting heads of each wood shaper, hand-fed panel raiser, or other similar machine not automatically fed, shall be enclosed with](https://reader034.vdocuments.site/reader034/viewer/2022042108/5e8883443b9a605f2857ba12/html5/thumbnails/67.jpg)
67
1910.219
Mechanical Power-Transmission Apparatus
![Page 68: Subpart O - Machine Guarding · 2014-05-12 · The cutting heads of each wood shaper, hand-fed panel raiser, or other similar machine not automatically fed, shall be enclosed with](https://reader034.vdocuments.site/reader034/viewer/2022042108/5e8883443b9a605f2857ba12/html5/thumbnails/68.jpg)
68
1910.219(a)
This section does not apply to the following belts operating at 250 fpm or less:
Flat belts 1 inch or less wideFlat belts 2 inches wide or less with no fasteners or metal lacingsRound belts 1/2 inch or less in diameterSingle-strand v-belts 13/32 inches wide or less.
![Page 69: Subpart O - Machine Guarding · 2014-05-12 · The cutting heads of each wood shaper, hand-fed panel raiser, or other similar machine not automatically fed, shall be enclosed with](https://reader034.vdocuments.site/reader034/viewer/2022042108/5e8883443b9a605f2857ba12/html5/thumbnails/69.jpg)
69
1910.219(a)
Vertical and inclined belts if not more than 2 1/2 inches wide, traveling at less than 1000 fpm, if free from metal lacings or fastenings may be guarded with a nip point belt and pulley guard.
![Page 70: Subpart O - Machine Guarding · 2014-05-12 · The cutting heads of each wood shaper, hand-fed panel raiser, or other similar machine not automatically fed, shall be enclosed with](https://reader034.vdocuments.site/reader034/viewer/2022042108/5e8883443b9a605f2857ba12/html5/thumbnails/70.jpg)
70
1910.219(b)(1)
Flywheels located so that any part is 7 feet or less above the floor or platform shall be guarded.Wherever flywheels are above working areas, guards shall be installed having sufficient strength to hold the weight of the flywheel in the event of a shaft or wheel mounting failure.
![Page 71: Subpart O - Machine Guarding · 2014-05-12 · The cutting heads of each wood shaper, hand-fed panel raiser, or other similar machine not automatically fed, shall be enclosed with](https://reader034.vdocuments.site/reader034/viewer/2022042108/5e8883443b9a605f2857ba12/html5/thumbnails/71.jpg)
71
1910.219(c)
Horizontal, vertical, and inclined shafting must be enclosed.Projecting shaft ends shall present a smooth edge and end and shall not project more than 1/2 the diameter of the shaft unless guarded by non rotating cap or safety sleeves. Unused keyways shall be filled up or covered.
![Page 72: Subpart O - Machine Guarding · 2014-05-12 · The cutting heads of each wood shaper, hand-fed panel raiser, or other similar machine not automatically fed, shall be enclosed with](https://reader034.vdocuments.site/reader034/viewer/2022042108/5e8883443b9a605f2857ba12/html5/thumbnails/72.jpg)
72
1910.219(d)
Pulleys less than 7 feet above the floor or platform must be guarded.Pulleys with cracks or pieces broken out of rims shall not be used.
![Page 73: Subpart O - Machine Guarding · 2014-05-12 · The cutting heads of each wood shaper, hand-fed panel raiser, or other similar machine not automatically fed, shall be enclosed with](https://reader034.vdocuments.site/reader034/viewer/2022042108/5e8883443b9a605f2857ba12/html5/thumbnails/73.jpg)
73
1910.219(e)
With some exceptions, horizontal, vertical, and inclined belts must be guarded.
![Page 74: Subpart O - Machine Guarding · 2014-05-12 · The cutting heads of each wood shaper, hand-fed panel raiser, or other similar machine not automatically fed, shall be enclosed with](https://reader034.vdocuments.site/reader034/viewer/2022042108/5e8883443b9a605f2857ba12/html5/thumbnails/74.jpg)
74
1910.219(f)Gears must be guarded.Guarding of hand operated gears is highly recommended.All sprocket and chains must be enclosed unless more than 7 feet above the floor or platform.When frequent oiling must be done, openings with hinged or sliding self-closing covers must be provided.
![Page 75: Subpart O - Machine Guarding · 2014-05-12 · The cutting heads of each wood shaper, hand-fed panel raiser, or other similar machine not automatically fed, shall be enclosed with](https://reader034.vdocuments.site/reader034/viewer/2022042108/5e8883443b9a605f2857ba12/html5/thumbnails/75.jpg)
75
1910.219(i)
Collars shall be cylindrical, and screws or bolts used in collars shall not project beyond the largest periphery of the collar.Couplings shall be constructed so as to present no hazard from bolts, nuts, setscrews, or revolving surfaces.
![Page 76: Subpart O - Machine Guarding · 2014-05-12 · The cutting heads of each wood shaper, hand-fed panel raiser, or other similar machine not automatically fed, shall be enclosed with](https://reader034.vdocuments.site/reader034/viewer/2022042108/5e8883443b9a605f2857ba12/html5/thumbnails/76.jpg)
76
1910.219(o)
Wood guards may be used in the woodworking and chemical industries or other industries where conditions would cause rapid deterioration or where its location outdoors would make metal guards and railings undesirable. In all other industries, wood guards must not be used.