standard timber finished sizes and profiles … in pdf/tabma profile sheets.… · standard timber...
TRANSCRIPT
•QUALITY•SERVICE• INTEGRITY•
STANDARD TIMBER FINISHED
SIZES AND PROFILES
STANDARD TIMBER FINISHED
SIZES AND PROFILES
2005
1
Acknowledgements
This publication was formulated after lengthy consultation with industry together with input from
several industry associations and many producers, suppliers, wholesalers and merchants.
Forest and Wood Products Research and Development Corporation are the major sponsors of this
publication.
Acknowledgement is also given to both the NZ Pine Manufacturers Association and the NSW
Timber Importers Association for their invaluable in-kind contribution.
Published by the Timber & Building Materials Association (NSW) Ltd. ABN 12 000 045 956
13-29 Nichols Street, Surry Hills NSW 2010 Australia. PO Box 107, Surry Hills NSW 2010 Australia
Telephone (02) 9360 3088 Fax (02) 9360 3464 [email protected] www.tabma.com.au
Acknowledgements
Introduction
Contents
The principle objective of this document is to describe to the building
industry, specifiers, renovators and end-users standard timber sizes and
moulding profiles that are commonly available on the East Coast of
Australia. The document can be used by producers, suppliers and
importers to encourage uniformity in supply to the industry.
For information on availability please visit www.tabma.com.au to find
your closest TABMA member.
2–4
Engineered Wood Products .................................................................4
Architraves and Skirting .......................................................................5
Architraves and Skirting – Queensland and Northern NSW ................6
Sundry Treated Pine H3 Products Exterior Use .................................11
12–13
14
Internal Lining.....................................................................................15
Internal Staircase Components..........................................................16
17
18
Detail of Box Frame Material 44mm Sash Stock ...............................19
Treated Timber Hazard Level Guide ...................................................21
Mouldings – Full size and to Scale.....................................................22
Page
Industry Standard Timber Sizes .......................................................
Sundry Mouldings ............................................................................7–8
Protective Coated – Finger Jointed Pine ........................................9–10
External Wall Cladding .................................................................
Flooring and Decking .........................................................................
Door Jambs, Door and Casement Framing, Casement Sills .............
Detail of Box Frame Material 38mm Sash Stock ...............................
Window Framing ................................................................................20
Australian Government
Forest and Wood ProductsResearch and DevelopmentCorporation
© Copyright
•QUALITY•SERVICE• INTEGRITY•
imber ProfileTHE
BookTT
01/05©
CopyrightFW
PRD
C. Published
byTAB
MA
DISCLAIMER: Although TABMA has taken due care in preparing the information in this
document, it is intended merely as a guide to assist industry participants. In no way is TABMA
warranting the accuracy or completeness of the information. Nor is TABMA making any
representation on the suitability, safety, quality or availability of any product referred to in this
document. In making any decisions about products, based on the information in this document,
you should make your own independent enquiries in relation to the suitability, safety, quality
and/or availability of the products for your intended use.
Width Thickness
12 18 30 42 66 90 116 138
12 12 18 30 42 66 90
18 12 18 30 42 66 90 116 138
30
42
66
90
116
138
165 18
185 18 30 42 66 90
230
280
12 18 30 42 66 90 116 138
12 18 30 42 66 90 116 138
12 18 30 42 66 90 116 138
12 18 30 42 66 90 116
92 12 18 30 42
110 12 18 66 90
12 18 30 42 66 90 116 138
12 18 30 42 66 90 138
18 30 42 66 90
18 30 42 66 90
Table 1Species include
Finger Jointed
Pine (unprimed,
treated and
primed), Pacific
Maple, Oregon,
Victorian Ash,
Tasmanian Oak,
Hardwood, WRC
and other species
Kiln Dried
SECTION A
Notes: 1 All dressed timber will be square edged unless noted below.
2 92mm Queensland only. FJ.
3 Treated Pine DAR primed all pencil round 2.0mm radius
4 Pacific Maple, Oregon, WRC, Tasmanian Oak, etc, will be 235mm and 285mm..
5 Some species may have up to 1.0mm variation.
6 Finger Jointed Pine will be 11.0mm.
7 Special sizes can be produced subject to “Special Order”.
Width Thickness
12 19 35 42 45 70 90
12 12 19 42 70 90
19 12 19 35 42 70 90
3
42
1
1
190 19 35 45
240 19 35 45
290 19 35 45
5 42
12 19 35 42
45 35 70 90
70 12 19 35 45 70 90
90 12 19 35 45 70 90
120 19 35 45
40 12 19 35 45
70 19
Table 2Radiata Pine
Dressed
Appearance Grades
Kiln Dried
Appearance Grade Timber Dressed
Recommended Finished Timber Sizes
2
01/05©
CopyrightFW
PRD
C.Published
byTAB
MA
imber ProfileTHE
BookTT
Width Thickness
35 45 70 90
35 45 70 90
45 70 90
70 35 45 70 90
90 35 45 70 90
120 35 45
140 35 45 70
170 35 45
190 35 45 70
220 35 45
240 35 45 70
270 35 45
290 35 45 70
Table 1
Pine and
Hardwood KDSolid, Gauged
Width Thickness
30 42 65
66 30 42
90 30 42
138 30 42
140 65
180 65
185 42
230 42
240 65
280 42 65
88 88
112 112
135 135
185 185
F8 Treated Primed Pine Posts
88 112 135 185
Table 2
Pine Primed
Treated
H3 Finger Jointed &
Laminated includes
F7, GL8 & GL10
Kiln dried
Structural Timber
Notes: 1 Incorporates Radiata and KD Hardwood in all relevant F & MGP strength
ratings, treated or untreated.
Notes: 1 Treated Pine Primed Posts will have 2.0 mm radius pencil round.
2 Some sizes and grades are subject to availability at the time of order.
3 The above table and notes are based on the common sizes and grades available.
4 65mm only available in GL8 and GL10.
5 The above are suitable for above ground only.
SECTION B
Tables 1 and 2 are finished sizes relevant to the Australian building
industry, although comprehensive this does not describe exact market
availability
Recommended Finished Timber Sizes
3
01/05©
CopyrightFW
PRD
C. Published
byTAB
MA
imber ProfileTHE
BookTT
4
Sawn Timber Sizes
Width Thickness
38 50 75 100 125 150 200 250 30025
50 25 38 50
75 25 38 50 75
100 25 38 50 75 100
125 25 38 50 75
150 25 38 50 75
175 25
200 25
225 25
250 25
300 25
100 125
100 125 150
38 50 75 100 125 150
38 50 75 100 125 150 200
38 50 75 100 125 150 200
38 50 75 100 125 150 200 250
38 50 75 100 125 150 200 250 300
Notes: 1 Refer to the relevant standards for each species.
2 The above are common sizes; other sizes are available on request.
3 Fine sawn Oregon as per the dressed sizes.
SECTION C
Recommended Nominal Timber Sizes (unseasoned)
Sizes 36 45 63 75
95 36 45 63 –
130 36 45 63 –
150 36 45 63 75
170 36 45 63 –
200 36 45 63 –
240 36 45 63 –
300 – 45 63 75
360 – 45 63 –
400 – 45 63 75
450 – – 63 75
525 – – – –
(mm)
Notes: • Lengths to 14.4m in 300 increments.
• Treated or untreated.
• Refer to suppliers’ span tables.
Laminated Veneer Lumber (LVL)
Engineered Wood Products
Producer 1 200 x 44 240 x 51
300 x 51 360 x 58
400 x 58
er 2 200 x 70 241 x 70
302 x 70 356 x 70
406 x 70 200 x 90
241 x 90 302 x 90
356 x 90 406 x 90
er 3 200 x 68 245 x 68
300 x 68 360 x 68
200 x 88 245 x 88
300 x 88 360 x 88
er 4 200 x 47 240 x 47
246 x 47 246 x 57
300 x 63 360 x 63
Produc
Produc
Produc
I-Joists – Sizes by ProducerI
©Copyright
FWP
RDC.P
ublishedby
TABM
Aimber Profile
THE
BookTT01/05
ARCHITRAVES AND SKIRTING
Bullnose
Bevel
Half Splayed
Full Splayed
Pencil Round
18r 138
18
259419
138
1335
19 94 25
18
19 46 25
85
905
19 22 25
61
665 5
13 13
37
42
16
42
128
13 1316
66
2219 25
18
13 1316
12
6r 42
12
6r 66
22 2519
18
42
13 16 13
6r
Colonial*
18
5
Half Splayed Type B
9.518
5733
90
9.518
3333
66
8
2594
113
138
19
18
25
252219
25
66
41 25
42
17
13 16 13
90
19
25 65
46 25
NO
TTO
SCALE
5
Type A AS4
AS3
AS2
AS1
AS5 AS6
AS7
9018r
254619
6618r
252219
4218r
131613
138 x 18138 x 18 90 x 1890 x 18 66 x 1866 x 18 42 x 1842 x 18
138 x 18138 x 18 90 x 1890 x 18 66 x 1866 x 18 42 x 1842 x 18
138 x 18138 x 18 90 x 1890 x 18 66 x 1866 x 18 42 x 1842 x 18
138 x 18138 x 18 90 x 1890 x 18 66 x 1866 x 18 42 x 1842 x 18
90 x 1890 x 18 66 x 1866 x 18 42 x 1242 x 12 66 x 1866 x 18
42 x 1242 x 12 66 x 1266 x 1242 x 1842 x 18
6090
254619
3466
252219
4210
131613
*Refer to page 23 for full
size profile of Colonial
8
©Copyright
FWP
RDC. P
ublishedby
TABM
A
imber ProfileTHE
BookTT
259419
138
01/05
ARCHITRAVES AND SKIRTINGS
Queensland and Northern NSW
Splayed
66 42
AS8
66 x 1166 x 11 42 x 1142 x 11
11 11
Bullnose
66
AS9
66 x 1166 x 11
11
Colonial 2 AS10
66 x 1166 x 11
66
11
42 x 1142 x 11
11
42
77mm dia.
Step AS12
66 x 1166 x 11
66
11
42 x 1142 x 11
11
42
Queensland Colonial AS13
66 x 1166 x 11
66
11
42 x 1142 x 11
42
8mm dia.10mm dia.
11
Classic
66 42
AS14
66 x 1166 x 11 42 x 1142 x 11
11 11
Pencil Round AS15
42 x 1142 x 1166 x 1166 x 11
66
11 11
42
6mm dia.
6
NO
TTO
SCALE©
CopyrightFW
PRD
C.Published
byTAB
MA
imber ProfileTHE
BookTT01/05
Square Edged
6r
30
2: 8
6r
42
2: 8
11
11
42
42
6
6
30
30
5
5
23
23
5
5
18
18
5
5
12
12
42
42
30
30
23
23
18
18
12
12
8
8
11
11
42
42
6
6
Note: 25% of width backed off
38*mm Nosing
30
66
30
42
30
30
11
90
5r
5r
55
30
11
66
5r
5r
18
10
30
10
Cover Strip
Half Round
Cover StripQuad
Scotia
Ovolo
30
8
42
8
79
90
Full
Splayed
SM1
42
3023
1812 8
SM2
42
3023 18
12
42
SM3
5
23
23
5
5
5
6
30
30
6
6
6
5
18
18
44
5
5
12
12
33
5
3023 18
12
18 x 1018 x 10 30 x 1030 x 10
SM5
SM4
SM6
SM7
SM8
90 x 3090 x 30 66 x 3066 x 30 42 x 3042 x 30
90 x 3090 x 30 66 x 3066 x 30 42 x 3042 x 30
SUNDRY MOULDINGS
7
31
30
42
5r
5r
11
NO
TTO
SCALE©
CopyrightFW
PRD
C. Published
byTAB
MA
imber ProfileTHE
BookTT
01/05
8
Inlay Bolection
3030
4242
42
29 13
1218
18r
6
29
26
42
16
13
1218
6
8
66
1218
6
8
25 41
53 13
66
53 13
1218
6
Sash Stop Bead
19
10
5
21212
23
10
5
2
12
30
5
2
1012
42
5
2
5.5r
10
16
30
5
2
1416
42
5
2
5.5r
14
10
22
Picture Rail
10
19
6
10
158
832
618
12
9
16
16
6
8 8
Parting Bead
Glazing Bead Sash Bead Colonial GLZ Bar
Stormould External Corner
30mm 42mm
5.5r
5.5r
5.5r 5.5r
18r
10 10
12 12
10
9
4230
40
2010
SUNDRY MOULDINGS (cont.)
SM9
30 x 1030 x 10
SM10
30 x 1030 x 10
42 x 1242 x 12 42 x 1242 x 12
SM11
42 x 1642 x 16
42 x 1242 x 12
30 x 1630 x 16
30 x 1230 x 12
23 x 1223 x 12 19 x 1219 x 12SM12
42 x 1842 x 18 66 x 1866 x 18
42 x 1842 x 18 66 x 1866 x 18
SM13
SM14 SM15 SM16
SM17 SM18
NO
TTO
SCALE©
CopyrightFW
PRD
C.Published
byTAB
MA
imber ProfileTHE
BookTT01/05
9
Handrails
20
42
79
63
20
44
88
32
42
25 mm Fascia 18 mm Fascia
23r
8 8 2525
25
135
25
25
25
23r
8
6 6
8
180
25
18
25
16r
8 8
180
16r
8 8 2525
18
135
Bottom Rails
42
28 31
86
30
PROTECTIVE COATED TREATED H3
FINGER JOINTED PINEEXTERIOR USE (above ground only)
20
42
42
66
12 12
80
30
4.5
46 25
66
4212 12
30
85
*Refer to page 23 for full size profile
T1
79 x 6379 x 63
T2
88 x 4288 x 42
T3
66 x 4266 x 42
T4
80 x 3080 x 30
T5
86 x 4286 x 42
T6
66 x 3066 x 30
T7
180 x 25180 x 25
T8
180 x 18180 x 18
135 x 25135 x 25 135 x 18135 x 18
27
11
16
15
NO
TTO
SCALE©
CopyrightFW
PRD
C. Published
byTAB
MA
imber ProfileTHE
BookTT
2r
2r
2r
2r
2r2r2r
01/05
10
Posts
Structural BeamsLaminated Beams
Weather Boards
135
135
2.0r
112
112
2.0r
88
88
2.0r
FJ and laminated
65
140
2.0r
65
180
2.0r
65
240
2.0r
65
280
2.0r
65
320
2.0r
138
8
5
518
9
16
4
122 cover
50
46r
PROTECTIVE COATED TREATED H3
1185
185
2.0r
EXTERIOR USE (above ground only)
185
8
5
518
9
16
4
169
70
46r
T9
185 x 185185 x 185
88 x 8888 x 88
135 x 135135 x 135
112 x 112112 x 112
T10
140 x 65140 x 65 180 x 65180 x 65 240 x 65240 x 65
280 x 65280 x 65 320 x 65320 x 65
T11
138 x 18138 x 18 185 x 18185 x 18
FINGER JOINTED PINEN
OT
TOSCALE
©Copyright
FWP
RDC.P
ublishedby
TABM
Aimber Profile
THE
BookTT01/05
11
Lattice surround
H3 PRODUCTS
SUNDRY TREATED PINE
Fence capping
8
10 38
135
30
39
6r
35
90
34 22 34
6r
35
70
24 22 24
To fit sawn lattice
6r
35
90
31 28 31
6r
35
70
21 28 21
To fit dressed lattice
20 50
115
2835
13
EXTERIOR USE (above ground only)
T25
90 x 3590 x 35 70 x 3570 x 35
90 x 3590 x 35 70 x 3570 x 35
T30
115 x 35115 x 35 135 x 39135 x 39
Important Recommendations when using Treated Timber
1 Use corrosion resistant fasteners, i.e. hot dipped galvanised or
stainless steel bolts, plates, nails, etc.
2 End seal after cutting and seal all housed or checked joints prior
to installing.
3 As a general rule use oil-based undercoats over primed treated
timber.
NO
TTO
SCALE©
CopyrightFW
PRD
C. Published
byTAB
MA
imber ProfileTHE
BookTT
01/05
12
White Cypress
Round log cabin
Flat log cabin
75
15
1020
10
Flat double log cabin
Rusticated
7515
10
40
46r
5
520
10
5
85
10
5
520
10
115
5
125
46r
Unseasoned
EXTERNAL WALL CLADDING
10
69 21
70r
Round double log cabin
125
10 10
10
20
115
56.556.5 621
48r 48r
125
10 10
10
20
115
56.556.5 621
10r 10r10r 10r
75
10 10
10
20
115
6921
10r10r
4550
110
10
5
520
10
115
5
160
46r60 110
10
5
520
10
115
5
170
46r70
Checked and nosed (tear drop)
90
9
75
2012
15
8
9
20r
Double checked and nosed (double tear drop)
62
9
125
2012
15
8
9
20r
78
20r
ex 100 x 25ex 100 x 25 ex 150 x 25ex 150 x 25
ex 100 x 25ex 100 x 25 ex 150 x 25ex 150 x 25
ex 100 x 25ex 100 x 25 ex 150 x 25ex 150 x 25
ex 175 x 25ex 175 x 25 ex 200 x 25ex 200 x 25
ex 100 x 25ex 100 x 25 ex 150 x 25ex 150 x 25
EC1 EC2
EC3 EC4
EC5
EC6 EC7
NO
TTO
SCALE©
CopyrightFW
PRD
C.Published
byTAB
MA
imber ProfileTHE
BookTT01/05
13
EXTERNAL WALL CLADDING
Western Red Cedar
Unseasoned select – Bevel sawn siding
Seasoned clear grade
Note: Recommended cover 160
194.5
190
17 4.5
190
Tongued and Grooved
V Joint
Sawnface
168
6
150 cover
19 5
5
9 7
19
8 9
5
75
55
6.25
6.2519
84 cover
92
6.56
6
84 cover8
3092
6
67
9
19 6.56.25
6.25
133 cover
141
8
6
67
9
30
19 6.56.25
6.25
Shiplap Sawn Face Treated CCA Kiln Dried Siding
140
126 cover
16
6.8
5.86.4
5
530
19
9
66
7
126 cover
14016
6.8
5.86.4
5
530
19
9
66
7 19
170
6
Baltic Pine
Checked and Chamfered
Radiata Pine
Treated Seasoned
Shiplap
5
5
8
19 6.56.25
6.25
133 cover
1419
75
5
6
6
Shiplap Dressed face Rusticated Dressed Face
5088
10
5
519
10
15
4
125
46r
EC8
140 x 19140 x 19
EC9
EC10
EC11
EC12 EC14
EC13 EC15
140 x 19140 x 19
140 x 19140 x 19
170 x 19170 x 19
ex 200 x 25ex 200 x 25
ex 200 x 25ex 200 x 25
ex 100 x 25ex 100 x 25
ex 150 x 25ex 150 x 25
ex 100 x 25ex 100 x 25
ex 150 x 25ex 150 x 25
ex 175 x 25ex 175 x 25
(cont.)
NO
TTO
SCALE©
CopyrightFW
PRD
C. Published
byTAB
MA
imber ProfileTHE
BookTT
01/05
14
FLOORING AND DECKING
Decking Seasoned
62
56
20
19
19
701.5r
Hardwood Structural Flooring
7 83 cover
7 113 cover
7 133 cover
8.6
8.6
8.6
76.3
6.36.4
76.3
6.36.4
76.3
6.36.4
860 cover
6
766.25
6.256.519
6.5
6.5619
6.5
6.5619
6.5
6.5619
9
7
99.25
9.25
6.525
1.5r
19
64
1.5r
19
86
1.5r
Secret nail
White Cypress Radiata Pine
764
3
7
76.5
3.53
3 3
8
85
78
20
764
3
7
76.5
3.53
3 3
8
98
91
20
764
3
7
76.5
3.53
3 3
8
135
128
20
764
3
7
76.5
3.53
3 3
8
Hardwood Reversible
70
22
22
1.5r
1.5r
1.5r
1.5r
Pine Treated Reversible Hardwood Local
Baltic100
7
7.58
6.5622
6
0.5
7
152
7
7.58
6.5622
6
0.5
7
10 10
10 10
5 6
9.5 8
6
766.25
6.256.519
5 6
9.580 cover
6
766.25
6.256.519
5
9.5130 cover
860 cover
9.5
5 6
80 cover
9
7
99.25
9.25
6.525
8 9.5
5 6
FD1ex 75 x 25ex 75 x 25 ex 100 x 25ex 100 x 25
Top nail FD2
Secret nail FD3
ex 150 x 25ex 150 x 25
ex 75 x 31ex 75 x 31 ex 100 x 31ex 100 x 31
FD5 FD6
ex 75 x 25ex 75 x 25 ex 100 x 25ex 100 x 25
ex 100 x 25ex 100 x 25ex 125 x 25ex 125 x 25
ex 113 x 25ex 113 x 25
ex 150 x 25ex 150 x 25
FD7ex 125 x 25ex 125 x 25
ex 150 x 25ex 150 x 25
FD8 FD9 FD10
70 x 1970 x 19 70 x 2270 x 22 64 x 1964 x 19
90 x 1990 x 19 90 x 2290 x 22 86 x 1986 x 19
90
4
3.013
5
80 cover
80 x 1380 x 13
6.1
3.93.5 136.0
3.5
1.4r
1.2r13.5 14141414
Hardwood Solid Overlay Flooring
FD12
68
21
1.5r
White Cypress FD11
68 x 2168 x 21
68
21
68 x 2168 x 21
NO
TTO
SCALE©
CopyrightFW
PRD
C.Published
byTAB
MA
imber ProfileTHE
BookTT
10 10
90
(based on 450mm centre)
01/05
133 cover
133 cover
6
7
3
8.6
63.5
6.3
6.36.4
63.5
140
6.5
6.56
12 4.33.85
3.85 3 33
3
3.7
3.7
7.390
4.6
83 cover
7
7
7
63.5
3
3
3.7
3.74.6
3 3.7
3.74.6
12 4.3
3
3.85
3.85
12 4.33.85
3.85
10 3
970
82 cover
82 cover
91
91
154
154
213.5
2.5
3 34
3.5
3.5
36
63
6
3.52.5
4
70
133
133
21
21
21
9
9
9
3
3
15 36
6
15 36
10 33.5
3.5
3
3
3
196.5
6.56
6.3
6.36.4
3
7
7
140 8.6
83
3
3
36
140 7.3
20140 7.3
140
133 cover
86 cover
86 cover
137 cover
133 cover
142
10
63.5
10
15
91
91
3.5
3.5
6
6
1.5
1.5
1.5
1.5
5
5
5 5
5
6
6
6
1.5
5
138
133
5
5
5
5
3
3
6
6
5
3
3
103.5
3.53.5
3.5 1.5
1.53
10
10
5
5
1.5
1.53
34
3
3.252.25
3
3 9
3
34
3
5
1.54
1.5
1.5
12
44.5
7.363.5
123.85
3.7
3.7
3.854.6
6.5
4.3
133 cover
6 363.5
63.5133 cover
63
63.5
45
45
45
45
45
Internal Panelling – Tongued and Grooved
PineDouble V Jointed and Centre GrooveV Jointed and Centre V Groove
Double V Jointed and Centre V Groove
Regency V Jointed
Shiplap
V Jointed – Regency – Centre Groove and Shiplap
V Jointed
Western Red Cedar Tasmanian OakSeasoned & Seasoned
Seasoned
No. 312
No. 315
No. 321 No. 322
No. 301
No. 302
3
L1 L2
L3
L4 L5
L7
15
INTERNAL LINING
L6
6
6
6
6
19
NO
TTO
SCALE©
CopyrightFW
PRD
C. Published
byTAB
MA
imber ProfileTHE
BookTT
01/05
16
Handrails
INTERNAL STAIRCASE
COMPONENTS
66
41
66
41
65
65
65
65
80
65
65
65
IS1 66 x 4166 x 41 IS2 66 x 4166 x 41
IS3 65 x 6565 x 65 IS4 65 x 6565 x 65
80
65
IS5 80 x 6580 x 65 IS6 80 x 6580 x 65
IS7 65 x 6565 x 65
NB Inside grooving can vary between 12, 16,
38, 42, and 44mm width and 8mm depth.
NO
TTO
SCALE©
CopyrightFW
PRD
C.Published
byTAB
MA
imber ProfileTHE
BookTT01/05
17
75*mm Door Framing & Jambs
50*mm Door Framing & Jambs
Casement Sills
30*mm Jamb Lining
38*mm Threshold
138117
92
66 40
13
13
6653
13
38
38
3845
45
454754
93100
72
79
138117
92
38
38
3845
45
13
138
13
51
66
85
11
31
20
13 76 16 43 156169
38
6
6 102516142
111
34
1025 6
6
16
51
66
454754
93100
72
79
75*mm Door Mullions
140118
9066
41
13
28
38
38
3845
45
452128
72
79
47
54
384593
100
94
28
79 / 7238
38
13
30
17
4545
100
79
47
140118
9066
94
30mm Jambs FJ Pine only
38
13
30
17
138116
90
110
Note: refer to pages 17–18 for Box Frame Window Sill Profiles
DOOR JAMBS
DOOR AND CASEMENT FRAMING
CASEMENT SILLS
J1 J2
J3
J4
J5
J6
J7
NO
TTO
SCALE©
CopyrightFW
PRD
C. Published
byTAB
MA
imber ProfileTHE
BookTT
01/05
18
Vertical Section through Sill
Sashes and Head
Section
through
Mullion
NOTE: This detail
is suitable for
lead weights
13
33
33
6
46
10
35
19
19 53 19
115
1212
916
Mullion
Inside Lining
No.67
Pulley Styles
No.59
Mullion
Outside Lining
No.68
Bottom
Sash
Top
Sash
Parting Bead
No. 6
Stop Bead
No. 9
Bottom
Sash
Top
Sash
DETAIL OF BOX FRAME
MATERIAL AND
38mm SASH STOCK
Inside Lining
Head Only
Outside Lining
Head Only
3
3743
6
12 129
13 19
35
41
46 10
6
3319
13
14
19
5.5r
2
19
30
91
Pulley Style
Head Lining No. 52
Stop Bead
No. 8
Parting Bead
No. 6
Sash Style
and Top Rail
No. 60
S1 S2
33
12
5448
12 9
3 6
Sash Style
and Top Rail S3
67
3
19
6
33
912 12
Sash Bar
S5
6
66
33
8
60
3
912 12
Bottom
Rail
S6
6
33
8
8591
12 91
3
12
Bottom Rail
(NOTE: Undersideif bottom rail splayedwhen fitting sash.)
S7
NOTE: Back lining
for brick buildings
only
Section
through
Left Hand
Box
13
666 13
46
10
33
3335
1219
78
19
91
Bottom
Sash
Top
Sash
Outside Lining
No. 70
Front edge
of sill
Pulley Style
No. 59
Inside Lining
S9
33
8
11
66
85
142
16 1025
38
6
6
55
22
Box Frame Sill
S8
Section
through
Mullion
NOTE: This detail is
suitable for round
cast iron weights
11 1119
19
19
13
138
91
100
160
Mullion Inside Lining
No.65
Pulley Styles
No.59
Mullion Outside Lining
No.66
Bottom
Meeting Bar
S4 6
6 8
36
27
33
912
12
35
35
27
42
42
Top
Meeting Bar
No. 66
NO
TTO
SCALE©
CopyrightFW
PRD
C.Published
byTAB
MA
imber ProfileTHE
BookTT01/05
19
6
8 10
36
34
40
1114
13
43
43
34
49
49
6
7
3
19
6
39
1114 14
33
8
11
66
111
168
16 1025
34
6
6
55
22
13
39
39
6
46
10
41
19
19 53 19
115
1212
916
6
39
10
8591
14 11
3
14
6
66
39
10
60
3
1114 14
11 1119
19
19
13
138
97
100
160
Vertical Section through Sill
Sashes and HeadSection
through
Mullion
NOTE: This detail is
suitable for round
cast iron weights
Section
through
Mullion
NOTE: This detail
is suitable for
lead weights
Mullion Inside Lining
No.65
Pulley Styles
No.59
Mullion Outside Lining
No.66
Mullion
Inside Lining
No.67
Pulley Styles
No.59
Mullion
Outside Lining
No.68
Bottom
Sash
Top
Sash
Parting Bead
No. 6
Stop Bead
No. 9
Top
Meeting Bar
No. 66
Bottom
Meeting Bar
Bottom Rail
Sash Bar
Bottom
Rail
(NOTE: Undersideif bottom rail splayedwhen fitting sash.)
NOTE: Back lining
for brick buildings
only
13
666 12
46
10
39
3941
1219
78
19
97Section
through
Left Hand
Box
Bottom
Sash
Top
Sash
Outside Lining
No. 70
Front edge
of sill
Pulley Style
No. 59
Inside Lining
Box Frame Sill
Bottom
Sash
Top
Sash
3
3743
6
14 1411
13 19
41
41
46 10
6
3919
13
14
19
5.5r
2
19
30
97
Inside Lining
Head Only
Outside Lining
Head Only
Pulley Style
Head Lining No. 52
Stop Bead
No. 8
Parting Bead
No. 6
Sash Style
and Top Rail
No. 60
DETAIL OF BOX FRAME
MATERIAL AND
44mm SASH STOCK
S17
S18
S16
S15
S14
S13
S11S10
Sash Style
and Top Rail
39
14
5448
14 11
3 6
S12
NO
TTO
SCALE©
CopyrightFW
PRD
C. Published
byTAB
MA
imber ProfileTHE
BookTT
01/05
20
WINDOW FRAMING
41
44
133
12 1217
19
143
12
12
70 19
12
29
19
41
133
44
1970
133/168
12
29
41
133
70
19
12 29
44
32
12
41
12 29
133
32
44
19
22 19
12
10
8
17 6
18/24
6
10
15
8
12
1922
32
57
8
8
32
12 20
12
19
143
6
18
12
9
16
16
6
8 8
Colonial GLZ Bar HeadSash
Chair Rail
Sash BeadGlazing Bead
Wind Mould
Chair Rail
Sill
Style
Transom
Mullion WF1 WF2 WF4WF3
WF5 WF6
WF7
WF8 WF9
WF10
WF11 WF12
NO
TTO
SCALE©
CopyrightFW
PRD
C.Published
byTAB
MA
imber ProfileTHE
BookTT01/05
21
Inside, above ground,
dry
Insect borer (other than
termites) hazard
Framing, flooring,
furniture, etc
Generally to order
Using treated timber in a higher hazard level than it is intended for may result in premature failure.
Note that the hazard level of treatment is not related to the stress grade or other engineering
properties of the timber.
TREATED TIMBER
HAZARD LEVEL GUIDE
Availability
H1
Inside, above ground,
dry
Insect borer and termite
hazard
Framing, flooring,
trusses
Stocks available:
framing 70 x 35
90 x 35
70 x 45
90 x 45
other sizes to order
H2
Outside, above ground Moderate fungal decay
and termite hazard
Decking, fencing,
cladding, fascia, window
joinery, exterior
structural timber
Available ex-stockH3
Outside, in ground High fungal decay and
termite hazard
Fencing, greenhouses,
pergolas, non-structural
and landscaping timbers
Available ex-stockH4
Outside, in ground or
fresh water
High fungal decay and
termite hazard
Engineered retaining
walls, building poles,
pilings and cooling
tower fill, structural or
critical applications
Generally to orderH5
Marine water exposure Marine borers hazard
Marine piles, jetty
crossbracing, landing
steps, sea walls
Generally to orderH6
Exposure Typical use/Hazard
©Copyright
FWP
RDC. P
ublishedby
TABM
A
imber ProfileTHE
BookTT
01/05
22
MOULDINGS
Full Size and to Scale
Handrail T1 79 x 6379 x 63
Colonial AS2 66 x 1866 x 18
Handrail T2 88 x 4288 x 42
©Copyright
FWP
RDC.P
ublishedby
TABM
Aimber Profile
THE
BookTT01/05
Published by the Timber and Building Materials Association (NSW) Limited
ABN 12 000 045 956. 13–29 Nichols Street, Surry Hills, NSW 2010 Australia
PO Box 107, Surry Hills NSW 2010 Australia
Telephone (02) 9360 3088. Fax (02) 9360 3464
Supplied by
Australian Government
Forest and Wood ProductsResearch and DevelopmentCorporation
© Copyright
•QUALITY•SERVICE• INTEGRITY•