T o m l i n C o r p o r a t i o n P h . 2 1 6 - 6 4 1 - 1 8 0 0 F a x . 2 1 6 - 6 4 1 - 5 2 5 0

Page 1

Spill Containers

517 Series

3 ½ Gallons AST Spill Container

518 Series

7 ½ Gallon AST Spill Container

515 Series

AST Remote Spill Container

Installed on aboveground storage tanks for the

purpose of containing small spills and drips from the

fill nozzle. 3 ½ gallon capacity. Steel construction.

Lockable and white powder coated. Available in 2”

and 4”.

Installed on aboveground storage tanks for the purpose of

containing small spills and drips from the fill nozzle. 7 ½

gallon capacity. Lockable with drain valve and vented lid.

Connects to 4” male (NPT) riser, and is white powder

coated. Female NPT x Female NPT. Available in 2” and 4”.

For use on aboveground storage tanks for the purpose of

containing fuel spillage during remote tank filling

operations. 15 gallon capacity. 12 gauge steel construction.

Lockable lid, and powder coated white for durability. 1”

NPT drain with locking ball valve included. Choice of one or

two fill ports, 2”, 3”, 4” or combination. 2” bung for pump.

Single column base is easily adjustable.

T o m l i n C o r p o r a t i o n P h . 2 1 6 - 6 4 1 - 1 8 0 0 F a x . 2 1 6 - 6 4 1 - 5 2 5 0

Page 2

Emergency Vents

Male Threaded Emergency Vents

Product SKU: 244OM

Female Threaded Emergency Vents

Product SKU: 244O

Flanged Emergency Vents

Product SKU: 244OF

Emergency vent (pressure relief only) used on aboveground storage tanks, as a code requirement that helps prevent the tanks from becoming over-pressurized and rupturing if exposed to fire. Available in 2”, 3”, 4”, 6”, and 8”.

The 244 emergency vent consists of a body and a black powder coated cover (2" not powder coated) that moves up and down on a center pin. Pressure inside the tank forces the cover to lift up off the vent seat, allowing air to exhaust. The center pin guides the movement. When pressure falls the cover lowers back down onto seat and the vent is automatically reset.

Warning: The 244 emergency vent is for “emergency pressure relief only” and must be used in conjunction with a “normal vent” or pressure vacuum vent such as a Morrison Fig. 354, 548, 748 or 749.

Warning: The 244 emergency vent must be properly sized and selected for each specific tank application in order to meet the proper “venting capacity” requirements. See the Morrison Vent Guide for further instructions.

Emergency vent (pressure relief only) used on aboveground storage tanks, as a code requirement that helps prevent the tanks from becoming over-pressurized and rupturing if exposed to fire. UL and ULC listed.

The 244 emergency vent consists of a body and a black powder coated cover (2" not powder coated) that moves up and down on a center pin. Pressure inside the tank forces the cover to lift up off the vent seat, allowing air to exhaust. The center pin guides the movement. When pressure falls the cover lowers back down onto seat and the vent is automatically reset.

Warning: The 244 emergency vent is for “emergency pressure relief only” and must be used in conjunction with a “normal vent” or pressure vacuum vent such as a Morrison Fig. 354, 548, 748 or 749.

Warning: The 244 emergency vent must be properly sized and selected for each specific tank application in order to meet the proper “venting

capacity” requirements. See the Morrison Vent Guide for further

instructions.

Emergency vent (pressure relief only) used on aboveground storage tanks, as a code requirement that helps prevent the tanks from becoming over-pressurized and rupturing if exposed to fire. UL and ULC listed.

The 244 emergency vent consists of a body and a black powder coated cover (2" not powder coated) that moves up and down on a center pin. Pressure inside the tank forces the cover to lift up off the vent seat, allowing air to exhaust. The center pin guides the movement. When pressure falls the cover lowers back down onto seat and the vent is automatically reset.

Warning: The 244 emergency vent is for “emergency pressure relief only” and must be used in conjunction with a “normal vent” or pressure vacuum vent.

Warning: The 244 emergency vent must be properly sized and selected for each specific tank application in

order to meet the proper “venting capacity” requirements. See the Morrison Vent Guide for further

instructions.

T o m l i n C o r p o r a t i o n P h . 2 1 6 - 6 4 1 - 1 8 0 0 F a x . 2 1 6 - 6 4 1 - 5 2 5 0

Page 3

Atmospheric Vents 354 Series

Updraft Vent

155S Series

Double Outlet Vent

Mushroom Vent Caps

Part Number Female NPT

4021 ¾”

4022 1”

4023 1 ¼”

4024 1 ½”

4025 2”

4027 3”

4028 4”

“Open” vent used on underground and aboveground tanks for motor fueling. Vent allows tank to “breathe” during filling/dispensing operations. Available in 1 ½”-4”. Note: Open vents will allow unrestricted evaporation of product. Construction Details Body: Aluminum Cap: Aluminum Screen: 40 Mesh Brass

Aluminum T-style vent used primarily on small fuel oil storage

tanks. Outlet ports on either side of the inlet with 20 mesh

stainless steel screen keeps debris out of the airway. Available

in ¾”-3”.

This popular style is used in the majority of installations in the United States, Alaska, and Canada . Rust-resistant zinc-plated cast iron design is available in female NPT sizes from 3/4" to 4". Each cap is designed with a 30 mesh screen, to prevent debris from entering the vent pipe.

T o m l i n C o r p o r a t i o n P h . 2 1 6 - 6 4 1 - 1 8 0 0 F a x . 2 1 6 - 6 4 1 - 5 2 5 0

Page 4

Fill Caps- Splash Fill

179 Series

179M Hinged Style Fill Cap- Aluminum, Male

178DT Series

Threaded Style Fill Cap- Drop Tube

Loose-seal style cap with hinged cover. For fill port of small

storage tanks. Lockable with a padlock. Aluminum or cast iron.

Also available with male or female threads. Cast iron caps

available painted black. Available 2”.

Tight-seal style threaded cap. For fill port of small storage tanks. Lockable with a padlock. Powder coated black. Body is available in iron (IB) or brass (BB). Cap is available in iron (IC) or brass (BC). Buna-N gasket. Available in 2”-4”.

Made for a drop tube with 2" straight pipe threads and Buna-N gasket.

T o m l i n C o r p o r a t i o n P h . 2 1 6 - 6 4 1 - 1 8 0 0 F a x . 2 1 6 - 6 4 1 - 5 2 5 0

Page 5

Fill Caps and Adaptors-Tight Fill

633 AST Series

Tank Inlet Spout Adaptors with Crossbar

1600 Series

Poppeted Kamvalok® Adaptors

Tight fill adaptors for use on remote

aboveground storage tanks. Available in

various materials and various sizes.

Part A

Part F

Fuel Delivery Couplers & Accessories are designed to connect fuel delivery transport truck hoses or nozzles to the fill pipe of an aboveground storage tank. The 633AST Series Adaptors, with a boss installed across the inlet, are designed to prohibit open-fills. Available in 2”.

Fuel Delivery Couplers & Accessories are designed to

connect fuel delivery transport truck hoses or nozzles

to the fill pipe of an aboveground storage tank.

Available in aluminum and stainless steel. Available in

1 ½ “-3”.

T o m l i n C o r p o r a t i o n P h . 2 1 6 - 6 4 1 - 1 8 0 0 F a x . 2 1 6 - 6 4 1 - 5 2 5 0

Page 6

Anti-Siphon Devices

Anti-Siphon Valves

Series 600

Solenoid Valve

Model 710

Anti-Siphon Valve with Expansion Relief

EBW’s Anti Siphon Valves are recommended for all above

ground storage applications to prevent fuel from exiting the

storage tank in the event of a broken line or leak. Each valve

has an adjusting mechanism allowing for various liquid head

pressure settings within the valve range. Available in sizes

¾ “-2”.

Installed on pipeline leading from an aboveground tank. This

valve is used to help prevent accidental siphoning of product

from the tank in the event of a fracture in the pipe or other

cause for leak downstream and below the liquid level.

Available in ¾” -3”, Aluminum and stainless steel, and AC or

DC coils.

Anti-Siphon Valve is used on storage tank systems to prevent

the formation of a siphon in the event of a line break or leak. It

will help prevent product loss, environmental contamination

and/or fire hazards. It is available in ¾”-1”.

T o m l i n C o r p o r a t i o n P h . 2 1 6 - 6 4 1 - 1 8 0 0 F a x . 2 1 6 - 6 4 1 - 5 2 5 0

Page 7

Overfill Prevention Valves

AST Overfill Prevention Valve

9095A

AST Overfill Prevention Valve

9095C Series

AST Overfill Prevention Valve

9095S Series

Installed at the fill port of an aboveground storage tank.

Used in a tight fill application, the valve terminates flow of

product when the liquid level reaches a preset warning level

(90-95% full). Available in 2” and 3”.

The 9095C Morrison Overfill Prevention Valve is designed

for use on low-profile top-loading aboveground storage

tanks and tanks that require a high level shutoff. The

9095C Overfill Prevention Valve is installed at the fill port

of a tank. Available in 2”.

The ULC listed Morrison Overfill Prevention Valve is

designed for use on low-profile, top-loading storage

tanks that require a high level shutoff. The valve

terminates the fill when the product reaches the

preset level. The valves can be retrofitted on existing

tanks and fits into a 2" opening. Available in 2”.

T o m l i n C o r p o r a t i o n P h . 2 1 6 - 6 4 1 - 1 8 0 0 F a x . 2 1 6 - 6 4 1 - 5 2 5 0

Page 8

Overfill Prevention Valves Mechanical Test Mechanism for use with 9095A Series Valves

Overfill Prevention Valve for Used Oil Systems

FMMASO Series

3’ x 4” Overfill Prevention Valve with Audible Alarm

Available in 2” and 3”.

Valve with optional alarm for use on used oil

evacuation systems which use an air operated

pump. Available in 2”.

Combination of #1228 C&B 3X4 Overfill Prevention Valve and #1400 Audible Alarm allows for high level alarm and Overfill Prevention of an AST through one opening. The C&B 3X4 is mechanical in operation and reliably shuts off the fuel supply of an AST at a predetermined level. Alarm is battery operated, intrinsically safe, and complies with NEMA requirements. 95 decibel alarm alerts delivery person when fluid in tank reaches the predetermined level.

T o m l i n C o r p o r a t i o n P h . 2 1 6 - 6 4 1 - 1 8 0 0 F a x . 2 1 6 - 6 4 1 - 5 2 5 0

Page 9

Overfill Monitors High Level/Interstitial Alarm

Gallon Gauge Alarm

918C

Provides an audible alarm for either a high or low level warning.

Incorporates an alarm box and a single-point level sensor. Contains

a battery powered, intrinsically safe, alarm unit that is mounted

remote from gauge. The single point level sensor is immersed in

the tank through a 2" NPT Female opening and is supported by a

nylon liquid tight cable connector, Teflon tubing and wire. The high

or low activation point is set at the factory. The order length

should be equal to the distance from the top of the 2" tank

opening to the desired activation level. The low level activation

point can be set up to 113". The interstitial monitor level can be set

up to 113" as well. Available with either 0-53" probe or 53"-113"

probe.

The Morrison Model 918C Gallon Gauge is used to

measure the liquid level in an aboveground storage

tank. The Gallon Gauge provides an approximate read

out clearly displayed in gallons, and can easily be read

from 20 feet away! The Morrison Gallon Gauge

eliminates the need to convert feet and inch gauge

readings to gallons. The 918C includes a high level

audible alarm.

T o m l i n C o r p o r a t i o n P h . 2 1 6 - 6 4 1 - 1 8 0 0 F a x . 2 1 6 - 6 4 1 - 5 2 5 0

Page 10

Overfill Monitors OPW 444TA AST Four Signal Tank Alarm and

144TA AST Liquid Level Tank Alarm

High/Low level Audible Fill Alarm

Model ATA-Tank Monitor

The OPW AST remote Four Signal Tank Alarm is designed to sense up to four different liquid levels or other signals using just one device. The OPW 144TA Tank Alarm is designed for liquid level sensing.

Our new Audible Fill Alarm can be retrofitted to all of our

most popular tank gauges. It is cost effective and easy to

maintain. This item can provide High Liquid Level Alarms,

Overfill Tank Alarm, Leak Detection Alarm, Low Level Alarm,

and Interstitial Alarms.

An intrinsically safe tank monitor can be used to monitor

high or low levels and/or leak detection. Available in 115

volt. Meets NEMA 4 requirements. One and two channel

panels available.

T o m l i n C o r p o r a t i o n P h . 2 1 6 - 6 4 1 - 1 8 0 0 F a x . 2 1 6 - 6 4 1 - 5 2 5 0

Page 11

Tank Gauging Gallon Gauge

818C

Electronic AST Mechanical Tank Gauge

1018

OPW 200 TG AST Mechanical Tank Gauge

The Morrison Model 818C Gallon Gauge is used to

measure the liquid level in an aboveground storage

tank. The Gallon Gauge provides an approximate read

out clearly displayed in gallons, and can easily be read

from 20 feet away! The Morrison Gallon Gauge

eliminates the need to convert feet and inch gauge

readings to gallons.

Monitors 1 to 4 aboveground storage tanks per console. Each gauge can be located up to 1000 ft. from the console. Can measure tanks up to 35 ft. in height, including vertical or horizontal cylindrical tanks and rectangular tanks. Accurate to 0.1”. Choose Feet-Inches, Inches or Gallons. Metric readout can also be selected as an option on the console.

The OPW 200TG Tank Gauge is designed for reading liquid levels in horizontal or vertical aboveground storage tanks. The 200TG Tank Gauge provides an accurate numerical counter readout, eliminating the need for any on-site manual gauging.

T o m l i n C o r p o r a t i o n P h . 2 1 6 - 6 4 1 - 1 8 0 0 F a x . 2 1 6 - 6 4 1 - 5 2 5 0

Page 12

Tank Gauging Type-D At-A-Glance Gauge

Type-K Leak Gauge

Type-O Overfill Alert

The At-A-Glance Type D Liquid Level Gauge is a reliable, swing arm type tank gauge used for measuring all types of liquid levels. This sight gauge’s simple mechanical design promotes durability, minimal upkeep, quick installation, and easy/inexpensive repairs.

This liquid level gauge is custom made in house to fit your tank. We can accommodate any size tank from 6 inches to 12 feet in depth, we can also account for double walls and pipe risers, and we offer multiple materials of construction to accommodate nearly any type of liquid.

The Leak Type K Gauge is a reliable, vertical type leak monitor used for detecting leaks in the annular/interstitial space of a double wall above ground containment tank (AST's). Its simple mechanical design promotes durability, minimal upkeep, quick installation, and easy/inexpensive repairs.

This Interstitial Leak Gauge is custom made in house to fit your tank. We can accommodate any size tank from 6 inches to 170 inches in depth.

The Overfill Alert Gauge is a high level visual gauge designed to visually alert you that your AST (tank) is near full. This overfill monitor's simple pop up mechanical design promotes easy installs, maximum durability, and low up-front costs.

Also, by purchasing our Overfill Alarm Accessory, you can turn your visual overfill gauge into an audible overfill alarm.

T o m l i n C o r p o r a t i o n P h . 2 1 6 - 6 4 1 - 1 8 0 0 F a x . 2 1 6 - 6 4 1 - 5 2 5 0

Page 13

Tank Gauging

Black Night

Red Fox

Jarhead

Numbers decrease as fluid level lowers indicating how many inches are left until the tank is empty. For use with oil, waste oil, diesel fuel, antifreeze, water and other fluids with a low flash point. Measures from 99”-0”. Available in 2” N.P.T. threads.

Numbers decrease as fluid level rises indicating how many inches are left until the tank is full. For use with oil, waste oil, diesel fuel, antifreeze, water and other fluids with a low flash point. Measures from 99”-0”. Available in 2 inch N.P.T. threads.

For use with oil, waste oil, diesel fuel, antifreeze, water

and other fluids with a low flash point. Available in 1 ½ “-2”

N.P.T threads.

T o m l i n C o r p o r a t i o n P h . 2 1 6 - 6 4 1 - 1 8 0 0 F a x . 2 1 6 - 6 4 1 - 5 2 5 0

Page 14

Emergency Valves 272 Series Internal Emergency Valve

External Emergency Valve-Ductile Iron

346 Series

Fire Safety Valves

12000 Series

Used to shut off flow in the event of fire. Fusible link holds

open spring actuated lever. Body mounts at the base of an

aboveground tank with plunger end projecting inside the

tank. Available in Brass and Ductile Iron. Available in 2”, 2 ½”,

3”, and 4” threaded and flanged.

Used to shut off flow in the event of fire. Fusible

link holds open spring actuated lever. Mounts on

external pipeline. Available in 1 ½”, 2”, and 3”.

Fusible Fire Safety Valves are designed to reduce fire

damage by shutting off the flow of oil from the oil tank in

the event of a fire. These valves conform to UL/ULC 842

and are listed in the US and Canada. They are required by

code in residential oil heating installations in conformance

with NFPA 31. Available in 3/8”-1”. FM NPT and Flare.

Available in brass construction.

T o m l i n C o r p o r a t i o n P h . 2 1 6 - 6 4 1 - 1 8 0 0 F a x . 2 1 6 - 6 4 1 - 5 2 5 0

Page 15

Emergency Valves Farm Tank Emergency Valve- Angle Type

474 Series

Farm Tank Emergency Valve-Straight Type

574 Series

Quick Opening Gate Valve with External Spring

238 Series

Emergency shutoff in case of fire. Male thread to

tank with plunger inside tank. Angled body to

female threaded outlet. Fusible link holds plunger

open. 5 PSI Maximum. Available 1” x ¾” and

1” x 1”.

Emergency shutoff closes in case of fire. Male

thread to tank with plunger inside tank. Straight

body with male threaded outlet. Fusible link holds

plunger open. 5 PSI Maximum. Available 1” x 1”.

Quick opening gate valves are manually-operated double disc gate valves designed for use where simple lever action opens or closes the valve. The 238 Series has an external spring and will remain closed when not held open. Can be held open with fusible link device. Available in 1 ¼” -3”. Available in brass construction.

T o m l i n C o r p o r a t i o n P h . 2 1 6 - 6 4 1 - 1 8 0 0 F a x . 2 1 6 - 6 4 1 - 5 2 5 0

Page 16

Pumps and Meters

For more information see section: Fuel Pumps and Accessories

T o m l i n C o r p o r a t i o n P h . 2 1 6 - 6 4 1 - 1 8 0 0 F a x . 2 1 6 - 6 4 1 - 5 2 5 0

Page 17

Decals and Placards

Many options available with specific wording and sizes

Please ask us about custom decals

Fuel Identification labels with numerous wording options in stock

Available in different color combinations

Available in 3” x 12”, or 4” x 13 ½”

Diamond placards are available with a variety of preprinted UN numbers

Available as a decal, metal sign, or rigid vinyl material

Two-sided rigid vinyl preprinted placards available

NFPA signs are available in several sizes

Vinyl decals, magnetic or aluminum material

Meets NFPA 704 requirements

Pre-numbered decals are offered for your convenience