spd62
DESCRIPTION
This is the data sheet of inductor which can be placed in transmission lines to avoid EMI/EMC issues.TRANSCRIPT
-
Actual Size
DASH NUMBER*
INDUCTANCE (H) 20%
DC RESISTANCE
MAXIMUM (OHMS)
CURRENT RATING
TYPICAL (AMPS)
TEST FREQUENCY (kHz)
SERIESShielded Surface Mount Inductors
Physical Parameters Inches MillimetersA 0.244 0.012 6.2 0.3B 0.260 .012 6.6 0.3C 0.118 Max. 3.0 Max.D 0.181 Ref. only 4.60 Ref. onlyE 0.059 0.007 1.5 0.2F 0.050 0.007 1.27 0.2G 0.015 Ref. only 0.38 Ref. only
Mechanical Configuration Units designed for surfacemounting; ferrite core and ferrite sleeve
Operating temperature range 55C to +125C
Application Frequency RangeValues 1.2H to 12H to 1.0 MHz Min.Values above 12H to 300 kHz Min.
Current Rating at 25C Ambient The maximum DCcurrent that will cause a 40C maximum temperature riseand where the inductance will not decrease by more than10% from its zero DC value
Packaging Tape & reel (16mm):13" reel, 1500 pieces max.; 7" reel not available
Note: No vias and traces in restricted area.
Power Inductors
270 Quaker Rd., East Aurora NY 14052 Phone 716-652-3600 Fax 716-652-4814 E-mail: [email protected] www.delevan.com
SPD62R
SERIES SPD62 FERRITE CORE & SLEEVE -122M -242M -352M -472M -682M -103M -123M -153M -183M -223M -273M -333M -393M -473M -563M -683M -823M -104M -124M -154M -184M -224M -274M -334M
3.50 2.80 2.50 2.00 1.80 1.40 1.30 1.20 1.10 1.00 0.94 0.82 0.78 0.70 0.68 0.56 0.50 0.41 0.39 0.37 0.35 0.32 0.29 0.22
0.08 0.10 0.12 0.15 0.17 0.18 0.20 0.30 0.35 0.40 0.45 0.50 0.70 0.75 0.85 1.20 1.45 1.60 1.70 1.80 2.10 2.20 3.00 3.30
100 100 100 100 100 100 100 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0
1.2 2.4 3.5 4.7 6.8 10 12 15 18 22 27 33 39 47 56 68 82 100 120 150 180 220 270 330
*Complete part # must include series # PLUS the dash #
For surface finish information, refer to www.delevanfinishes.com
Marking For values lower than 10H the R indicates a decimal point andthe remaining digits indicate the inductance in H. For values 10H andabove, the first two digits indicate the inductance in H and the third digitindicates the number of trailing zeros where a zero indicates that there areno trailing zeros.
Example: SPD62R-122M (1.2H) 1R2
Example: SPD62R-334M (330H) 331
6/2014