some experiences on choosing standards at kek
DESCRIPTION
Some Experiences on Choosing Standards at KEK. KEKB Controls Group 2002-08-21 by Tadahiko Katoh. Control Systems at KEK. KEK PS Control System TRISTAN Control System Renewed KEK PS Control System KEKB Control System. Standard used in PS Control System. System Design started in 1972 - PowerPoint PPT PresentationTRANSCRIPT
![Page 1: Some Experiences on Choosing Standards at KEK](https://reader035.vdocuments.site/reader035/viewer/2022062808/568154b2550346895dc2bd23/html5/thumbnails/1.jpg)
2002-08-21 EPICS Seminar at IHEP 1
Some Experiences on Choosing Standards at
KEK
KEKB Controls Group
2002-08-21by Tadahiko Katoh
![Page 2: Some Experiences on Choosing Standards at KEK](https://reader035.vdocuments.site/reader035/viewer/2022062808/568154b2550346895dc2bd23/html5/thumbnails/2.jpg)
Control Systems at KEK
- KEK PS Control System- TRISTAN Control System- Renewed KEK PS Control System- KEKB Control System
![Page 3: Some Experiences on Choosing Standards at KEK](https://reader035.vdocuments.site/reader035/viewer/2022062808/568154b2550346895dc2bd23/html5/thumbnails/3.jpg)
Standard used in PS Control System
- System Design started in 1972- Standards adopted- RS-232C
- Proprietary Systems- Network- Process Input/Output
![Page 4: Some Experiences on Choosing Standards at KEK](https://reader035.vdocuments.site/reader035/viewer/2022062808/568154b2550346895dc2bd23/html5/thumbnails/4.jpg)
Standards used in TRISTAN Control System
- Design started in 1981- Standards used- CAMAC Serial Highway(IEEE 596)- CAMAC Dataway(IEEE 483)- GPIB(IEEE 488)- MIL-1553B- RS-232C
- Proprietary System- Computer Network
![Page 5: Some Experiences on Choosing Standards at KEK](https://reader035.vdocuments.site/reader035/viewer/2022062808/568154b2550346895dc2bd23/html5/thumbnails/5.jpg)
Standards used in Second Generation PS Control System
- Renewal started in 1985- VMEbus(IEEE 1014)- Direct I/Os on VMEbus
- MAP(IEEE 801.4)- Broadband Token-Bus Network- CATV and Computer Network on one Coaxial
Cable
- GPIB(IEEE 488)- RS-232C
![Page 6: Some Experiences on Choosing Standards at KEK](https://reader035.vdocuments.site/reader035/viewer/2022062808/568154b2550346895dc2bd23/html5/thumbnails/6.jpg)
Standards in KEKB Control System
- Design Started 1993- VMEbus(IEEE 1014)- CAMAC(IEEE 596)- CAMAC(IEEE 483)- GPIB(IEEE 488)- FDDI- Ethernet(IEEE 801.2, 801.11)- 10 Base/T --> 100 Base/TX --> GbE
![Page 7: Some Experiences on Choosing Standards at KEK](https://reader035.vdocuments.site/reader035/viewer/2022062808/568154b2550346895dc2bd23/html5/thumbnails/7.jpg)
Life of the Accelerators
- KEK PS 30 years- TRISTAN 10 years- KEKB 10 - 20 years
![Page 8: Some Experiences on Choosing Standards at KEK](https://reader035.vdocuments.site/reader035/viewer/2022062808/568154b2550346895dc2bd23/html5/thumbnails/8.jpg)
Life of the Control Systems
- Electronic Equipment 10 - 20 years
- Consumer Electronics 7 years- Electronic Components10 - 20 years- IC’s(Supply) 20 years- Electrolytic Capacitors 10 years- Connectors
- VME Modules 10 years- Semiconductor Manufact. 5 years
![Page 9: Some Experiences on Choosing Standards at KEK](https://reader035.vdocuments.site/reader035/viewer/2022062808/568154b2550346895dc2bd23/html5/thumbnails/9.jpg)
Results of the Standards
- CAMAC(IEEE 483, IEEE 596)- Very simple and clear standard- Still widely used over the world- But careful design of the modules are req
uired- Parts especially SSI or MSI are obsolete
- VMEbus(IEEE 1014)- Very widely used- Will not be replaced by Compact PCI bus
![Page 10: Some Experiences on Choosing Standards at KEK](https://reader035.vdocuments.site/reader035/viewer/2022062808/568154b2550346895dc2bd23/html5/thumbnails/10.jpg)
Results of the Standard(2)
- MAP(IEEE 801.4)- Highly dependent on the automobile
industry(General Motors)- No second source of modules
- FDDI- It was a smart network standard- Expensive interface as ATM- Going to be obsolete in a few years- Replaced by Switched Ethernet
![Page 11: Some Experiences on Choosing Standards at KEK](https://reader035.vdocuments.site/reader035/viewer/2022062808/568154b2550346895dc2bd23/html5/thumbnails/11.jpg)
Results of the Standard(3)- GPIB(IEEE 488)- Widely used in Measuring Equipment- Optical Interface- Ethernet Interface- Behavior of the equipment is not always unpredi
ctable- Ethernet(IEEE 801.2, 801.11)- High Speed: 100 Base, Gb, 10 GbE- Wireless: 801.11a, 801.11b
- RS-232C, RS-485, RS-422/423- Physical Layer
![Page 12: Some Experiences on Choosing Standards at KEK](https://reader035.vdocuments.site/reader035/viewer/2022062808/568154b2550346895dc2bd23/html5/thumbnails/12.jpg)
How to Choose a Standard- Wait a little until the standard is widely
used.- A good standard is not always used
widely.- Don’t believe what a manufacturer
announces.- Check a module carefully before you
decide to use.- A manufacturer will never be your side
even if you are a good customer.
![Page 13: Some Experiences on Choosing Standards at KEK](https://reader035.vdocuments.site/reader035/viewer/2022062808/568154b2550346895dc2bd23/html5/thumbnails/13.jpg)
Standards that may be used Now
- Ethernet(IEEE 801.2, 801.11)- GbE, 100 Base/TX, 10 Base/T
- GPIB(IEEE 488)- You may use a GPIB equipment if it satisfi
es your requirements. Use with Ethernet.- CAMAC(IEEE 483, 596)- If you have already have CAMAC modules
- VME(IEEE 1014), VME64
![Page 14: Some Experiences on Choosing Standards at KEK](https://reader035.vdocuments.site/reader035/viewer/2022062808/568154b2550346895dc2bd23/html5/thumbnails/14.jpg)
Thank you for your attention!