siteline clad-wood window awning table of...
TRANSCRIPT
1
TABLE OF CONTENTS
Architectural Design Manual
February 2018
Product specifications may change without notice.
Questions? Consult JELD-WEN customer service.
SITELINE
CLAD-WOOD WINDOW
AWNING
Multiple Assemblies
Siteline clad awning windows may be mulled above, below, or beside other wood awning
windows, or other wood window products.
Dimensional Windows
Siteline clad awning windows may be specified as "dimensional", by adjusting the
desired rough opening width or height.
Siteline clad awning windows are available as operating, or stationary (non -
venting). Operating mechanism includes corrosion resistant steel hinges and roto
type operators for venting units. Sash locks are concealed unison type with an
exposed locking lever and escutcheon plate. There are several interior hardware
finish options. Refer to the Specifications for finish options.
GENERAL INFORMATION
Architectural Design Manual
February 2018
Product specifications may change without notice.
Questions? Consult JELD-WEN customer service.
SITELINE
CLAD-WOOD WINDOW
AWNING
Scale: NTS
2
Lite Cut Options
Special lite cut patterns can include a wide variety of straight line and radius patterns. The illustrations shown
above represent just a few of the possibilities. Rectangular, horizontal, vertical and Prairie lite patterns are
available in all standard size windows. Uneven, diamond, radius and Gothic lite cuts are available, subject to
approval.
Bar Alignment
Alignment of divided lite muntin bars from one window to the
next is often required by fine architectural design. Wood grilles,
GBG, and SDL's may be specified with muntin bars aligned.
Siteline Clad-Wood Awning Windows are available with removable Grilles, Grilles Between Glass (GBG), or
Simulated Divided Lites (SDL) in various styles and widths.
Rectangular Vertical Prairie
Uneven Diamond Radius
LITE CUT INFORMATION
Architectural Design Manual
February 2018
Product specifications may change without notice.
Questions? Consult JELD-WEN customer service.
SITELINE
CLAD-WOOD WINDOW
AWNING
Scale: NTS
3
26°
23°
Max. Opening
With 4" Limiter
Max. Opening
With 4" Limiter
Frame Height
Frame Height
Awning Vent Projection
The drawings above reflect full operation. Dimensions and angles above are approximate and will vary due to
frame height.
Narrow Operator
Frame Width under 21"
Roto type hardware
Roto type hardware
Note: Up to 4" max opening w/
window limiter device.
Standard Operator
Frame Width 21" and over
VENT PROJECTIONS
Architectural Design Manual
February 2018
Product specifications may change without notice.
Questions? Consult JELD-WEN customer service.
SITELINE
CLAD-WOOD WINDOW
AWNING
Scale: NTS
4
General Notes:
Unit size is always the maximum size of
the window with or without trim and does
not include nail fin.
Masonry Opening:
Masonry opening is always 1/2" over
(height and width) the unit size or the
outside of the trim of the window.
Rough Opening:
Rough opening is always 3/4" over frame
size of the window.
A
B
C
D
I
J
K
L
EF
GH
UNIT SIZING
Architectural Design Manual
February 2018
Product specifications may change without notice.
Questions? Consult JELD-WEN customer service.
SITELINE
CLAD-WOOD WINDOW
AWNING
Scale: NTS
5
11/16"5/8" 1"
1 1/8"7/8" 1 3/8"
5/8" GBG 23/32" Contour
GBG
1" Contour
GBG
Full Surround
1 3/8" Wood
Grille
Full Surround
1 1/8" Wood
Grille
Full Surround
7/8" Wood
Grille
InteriorExterior
Scale: NTS
6
GBG/SURROUND OPTIONS
Architectural Design Manual
February 2018
Product specifications may change without notice.
Questions? Consult JELD-WEN customer service.
SITELINE
CLAD-WOOD WINDOW
AWNING
1 1/8"7/8" 2 5/16"
1 3/8"
5/8"
Putty
7/8"
Putty
1 1/8"
Putty
1 3/8"
Putty
2 5/16"
Putty
7/8" 1 1/8" 1 3/8" 2 5/16"
7/8"
Bead
1 1/8"
Bead
1 3/8"
Bead
2 5/16"
Bead
NOTE: Various Combinations of the SDL Bars Shown are Available
5/8"
Exterior Interior
Scale: 6" = 1' - 0"
7
SDL OPTIONS
Architectural Design Manual
February 2018
Product specifications may change without notice.
Questions? Consult JELD-WEN customer service.
SITELINE
CLAD-WOOD WINDOW
AWNING
1 1/2"
1 3/4"
3"
1 5/16"
3"
1 1/4"
1 3/8"
1 1/4"
9/16"
1 1/2"
1 13/16"
5/16"
1 1/2"
1 5/16"
1 3/4"
2 1/4"
2 1/16"
1 1/16"
1"1/2"
Standard Nail
Fin
Brickmould
Beaded
Brickmould
3 1/2"
Flat Casing
Adams
Casing
Sill Nose Options
Standard Sill
Nosing
No Sill Nosing
1" Sill Nosing
2" Sill Nosing
Scale: 3" = 1' - 0"
8
TRIM AND SILL NOSE OPTIONS
Architectural Design Manual
February 2018
Product specifications may change without notice.
Questions? Consult JELD-WEN customer service.
SITELINE
CLAD-WOOD WINDOW
AWNING
Traditional Contemporary
GLASS STOP OPTIONS
Architectural Design Manual
February 2018
Product specifications may change without notice.
Questions? Consult JELD-WEN customer service.
SITELINE
CLAD-WOOD WINDOW
AWNING
Scale: NTS
9
6 9/16"
4 9/16"
1 5/32"
1 3/8"
5/8"
1 5/32"
5/8"
3 3/8"
7 15/16"
1 5/32"
4 3/4"
4 1/16"
1 1/8"
1 5/32"
9 5/16"
1 1/8"
5/8"
4 3/4"
1 3/8"
5/8"
7 1/4"
3 3/16" 3 3/16" 3 3/16"
3 3/16" 3 3/16"
4 9/16" Jamb Width 6 9/16" Jamb Width 7 15/16" Jamb Width
9 5/16" Jamb Width
5/4-4/4 Stacked Jamb
7 1/4" Jamb Width
5/4 Jamb Thickness
Kerfed Jamb Extension only available on 4/4 or 5/4 options
Maximum jamb length for 4/4 is 7 15/16".
Maximum jamb length for 5/4 is 7 1/4".
Maximum jamb length for 5/4 2 piece stacked is 12".
Scale: 3" = 1' - 0"
10
JAMB EXTENDER OPTIONS
Architectural Design Manual
February 2018
Product specifications may change without notice.
Questions? Consult JELD-WEN customer service.
SITELINE
CLAD-WOOD WINDOW
AWNING
5 15/16"
5 15/16"
2 5/16"
2 5/16"
4 3/4"
2 5/16"
4 3/4"
2 5/16"
5 15/16"
2 5/16"
Operating / Operating Operating / Stationary
Stationary
Operating
Direct Set
Operating
Direct Set / Operating
Scale: NTS
11
MULLION OPTIONS
Architectural Design Manual
February 2018
Product specifications may change without notice.
Questions? Consult JELD-WEN customer service.
SITELINE
CLAD-WOOD WINDOW
AWNING
7 15/16"
4 5/16"
2"
6 5/16"
4"
9 15/16"
3 5/16"
1"
6 15/16"
2 9/16"
6 1/8"
1/4"
Operating / Operating w/ 1/4"
Structural Mull Horizontal Section
Operating / Operating w/ 1" Solid
Spread Mull Horizontal Section
Operating / Operating w/ 2" Solid
Spread Mull Horizontal Section
Operating / Operating w/ 4" Solid
Spread Mull Horizontal Section
Scale: NTS
12
MULLION OPTIONS
Architectural Design Manual
February 2018
Product specifications may change without notice.
Questions? Consult JELD-WEN customer service.
SITELINE
CLAD-WOOD WINDOW
AWNING
4 5/16"
7 15/16"
2"
3 5/16"1"
6 15/16"
6 5/16"
9 15/16"
4"
2 9/16"
6 3/16"
1/4"
Stationary
Operating
W/ 1/4" Structural Mull Vertical
Section
W/ 1" Solid Spread Mull Vertical
Section
W/ 2" Solid Spread Mull Vertical
Section
W/ 4" Solid Spread Mull Vertical
Section
Stationary
Operating
Stationary
Operating
Stationary
Operating
Scale: NTS
13
MULLION OPTIONS
Architectural Design Manual
February 2018
Product specifications may change without notice.
Questions? Consult JELD-WEN customer service.
SITELINE
CLAD-WOOD WINDOW
AWNING
72"
18"
18"
36"
Note: Width and height combinations are limited to a maximum frame
size of 20 ft
2
.
Minimum Configuration
Maximum Configurations
60"
48"
MIN-MAX SIZING - OPERATOR
Architectural Design Manual
February 2018
Product specifications may change without notice.
Questions? Consult JELD-WEN customer service.
SITELINE
CLAD-WOOD WINDOW
AWNING
Scale: NTS
14
Minimum Configuration Maximum Configuration
84"18"
12"
84"
MIN-MAX SIZING - PICTURE
Architectural Design Manual
February 2018
Product specifications may change without notice.
Questions? Consult JELD-WEN customer service.
SITELINE
CLAD-WOOD WINDOW
AWNING
Scale: NTS
15
1 1/8"
1 1/8"
Da
ylig
ht O
pen
in
g
Sash
S
ize
2 1/16"
2 1/16"
Scree
n S
ize
1 5/8"
2 9/16"
5 13/16"
1 1/4"
1 1/4"
Ro
ug
h O
pe
nin
g
5/8"
5/8"
15/16"
15/16"
3 3/16"
4 9/16"
5 13/16"
3 3/16"
4 9/16"
Fram
e S
ize
3/8"
3/8"
Scale: 6" = 1' - 0"
16
OPERATOR - VERTICAL SECTION
Architectural Design Manual
February 2018
Product specifications may change without notice.
Questions? Consult JELD-WEN customer service.
SITELINE
CLAD-WOOD WINDOW
AWNING
5 13/16"3 3/16"
1 1/4"
5 13/16" 3 3/16"
1 1/4"
1 5/8"
Daylight
opening
Sash Size
Frame Size
Rough Opening
Screen Size
1 3/16" 1 1/8"
3/8" 3/8"
1 5/8"
2 1/16" 2 1/16"
15/16"
4 9/16" 4 9/16"
5/8" 5/8"
15/16"
Scale: 6" = 1' - 0"
17
OPERATOR - HORIZONTAL SECTION
Architectural Design Manual
February 2018
Product specifications may change without notice.
Questions? Consult JELD-WEN customer service.
SITELINE
CLAD-WOOD WINDOW
AWNING
Sash
S
ize
Ro
ug
h O
pe
nin
g
5 13/16"
Da
ylig
ht O
pen
in
g
2 1/16"
2 1/16"
1 1/8"
1 1/8"
Fra
me
S
ize
3/8"
3 3/16"
1 1/4"
5 13/16"
3 3/16"
1 1/4"
4 9/16"
4 9/16"
5/8"
5/8"
15/16"
15/16"
3/8"
Scale: 6" = 1' - 0"
18
PICTURE - VERTICAL SECTION
Architectural Design Manual
February 2018
Product specifications may change without notice.
Questions? Consult JELD-WEN customer service.
SITELINE
CLAD-WOOD WINDOW
AWNING
1 1/4"
Daylight
opening
Sash Size
2 1/16" 2 1/16"
5 13/16" 3 3/16"
1 1/4"
5 13/16"3 3/16"
Frame Size
Rough Opening
1 3/16" 1 1/8"
3/8" 3/8"
4 9/16"4 9/16"
5/8" 5/8"
15/16"15/16"
Scale: 6" = 1' - 0"
19
PICTURE - HORIZONTAL SECTION
Architectural Design Manual
February 2018
Product specifications may change without notice.
Questions? Consult JELD-WEN customer service.
SITELINE
CLAD-WOOD WINDOW
AWNING
Da
ylig
ht O
pen
in
g
Sash
S
ize
2 1/16"
2 1/16"
5 13/16"
1 1/4"
5 13/16"
1 1/4"
1 1/8"
1 1/8"
Fra
me S
ize
Scre
en
S
ize
1 9/16"
1 5/8"
4 9/16"
4 9/16"
5/8"
5/8"
15/16"
15/16"
3 3/16"
3 3/16"
Ro
ug
h O
pe
nin
g
3/8"
3/8"
Scale: 6" = 1' - 0"
20
PUSH-OUT CASEMENT - VERTICAL SECTION
Architectural Design Manual
February 2018
Product specifications may change without notice.
Questions? Consult JELD-WEN customer service.
SITELINE
CLAD-WOOD WINDOW
AWNING
5 13/16"
Screen Size1 9/16"
4 9/16"
Sash Size
3 3/16"
1 1/4"
5 13/16"
1 1/4"
3 3/16"
Frame Size
Rough Opening
1 1/8"1 3/16"
3/8" 3/8"
1 9/16"
4 9/16"
5/8" 5/8"
15/16" 15/16"
Daylight
opening
2 1/16" 2 1/16"
Scale: 6" = 1' - 0"
21
PUSH-OUT CASEMENT - HORIZONTAL SECTION
Architectural Design Manual
February 2018
Product specifications may change without notice.
Questions? Consult JELD-WEN customer service.
SITELINE
CLAD-WOOD WINDOW
AWNING
Daylig
ht O
pe
ning
Sa
sh
S
ize
2 1/16"
2 1/16"
1 1/8"
1 1/8"
Fram
e S
ize
5 13/16"
1 1/4"
4 9/16"
5/8"
5 13/16"
1 1/4"
4 9/16"
5/8"
15/16"
15/16"
3 3/16"
3 3/16"
Rou
gh O
pen
in
g
3/8"
3/8"
Scale: 6" = 1' - 0"
22
PUSH-OUT PICTURE CASEMENT - VERTICAL SECTION
Architectural Design Manual
February 2018
Product specifications may change without notice.
Questions? Consult JELD-WEN customer service.
SITELINE
CLAD-WOOD WINDOW
AWNING
Frame Size
Sash Size
5 13/16" 3 3/16"
1 1/4"
5 13/16"3 3/16"
1 1/4"
Rough Opening
1 3/16" 1 1/8"
3/8" 3/8"
15/16"
4 9/16" 4 9/16"
5/8" 5/8"
15/16"
Daylight
opening
2 1/16" 2 1/16"
Scale: 6" = 1' - 0"
23
PUSH-OUT PICTURE CASEMENT - HORIZONTAL SECTION
Architectural Design Manual
February 2018
Product specifications may change without notice.
Questions? Consult JELD-WEN customer service.
SITELINE
CLAD-WOOD WINDOW
AWNING
5 13/16"
1 1/4" 4 9/16"
Fram
e S
ize
Rou
gh O
pe
ning
1 1/8"
1 1/8"
Daylig
ht O
pe
ning
Sa
sh S
ize
2 1/16"
2 1/16"
Scree
n S
ize
1 5/8"
2 9/16"
5/8"
5/8"
15/16"
15/16"
5 13/16"
3 3/16"
1 1/4" 4 9/16"
3 3/16"
3/8"
3/8"
Scale: 6" = 1' - 0"
24
IMPACT OPERATOR - VERTICAL SECTION
Architectural Design Manual
February 2018
Product specifications may change without notice.
Questions? Consult JELD-WEN customer service.
SITELINE
CLAD-WOOD WINDOW
AWNING
5 13/16"3 3/16"
1 1/4"
5 13/16" 3 3/16"
1 1/4"
Daylight
opening
Sash Size
Frame Size
Rough Opening
Screen Size
1 3/16" 1 1/8"
3/8"
1 5/8"
3/8"
1 5/8"
2 1/16" 2 1/16"
4 9/16" 4 9/16"
5/8" 5/8"
15/16"15/16"
Scale: 6" = 1' - 0"
25
IMPACT OPERATOR - HORIZONTAL SECTION
Architectural Design Manual
February 2018
Product specifications may change without notice.
Questions? Consult JELD-WEN customer service.
SITELINE
CLAD-WOOD WINDOW
AWNING
4 9/16"
Da
yligh
t O
pe
nin
g
Sa
sh
S
ize
2 1/16"
2 1/16"
1 1/8"
1 1/8"
Fra
me
S
ize
Ro
ugh
O
pe
nin
g
3/8"
5 13/16"
3 3/16"
1 1/4"
5 13/16"
3 3/16"
1 1/4"
4 9/16"
5/8"
5/8"
15/16"
15/16"
3/8"
Scale: 6" = 1' - 0"
26
IMPACT PICTURE - VERTICAL SECTION
Architectural Design Manual
February 2018
Product specifications may change without notice.
Questions? Consult JELD-WEN customer service.
SITELINE
CLAD-WOOD WINDOW
AWNING
Daylight
opening
Sash Size
2 1/16" 2 1/16"
5 13/16" 3 3/16"
1 1/4"
5 13/16"3 3/16"
1 1/4"
Frame Size
Rough Opening
1 3/16" 1 1/8"
3/8" 3/8"
4 9/16"4 9/16"
5/8" 5/8"
15/16" 15/16"
Scale: 6" = 1' - 0"
27
IMPACT PICTURE - HORIZONTAL SECTION
Architectural Design Manual
February 2018
Product specifications may change without notice.
Questions? Consult JELD-WEN customer service.
SITELINE
CLAD-WOOD WINDOW
AWNING