sign and display adhesive - hawaii’s acrylic fabricator...science + innovation = smarter adhesive...

SIGN ANDDISPLAYADHESIVESELECTIONGUIDE

Offering the latest in adhesive

technologies required to bond

the wide range of substrates

typically found within the

Sign and Display market.

Science + Innovation= SMARTER ADHESIVE SOLUTIONS

ADHESIVES FOR PLASTICS DescriptionProduct

Non-flammable, water thin, very fast-setting solventcement for acrylic. Will also bond styrene, butyrate and polycarbonate to themselves.

3

Non-flammable, water thin, fast-setting solventcement for acrylic. Will also bond styrene, butyrate and polycarbonate to themselves.

4-SC

Two-component Kit, high strength, high viscosity structural adhesive for bonding large parts of, PVC, acrylic, ABS, and polycarbonate. Also bonds well to steel, non-anodized aluminum, other metals.

10

Medium bodied, fast-setting, high strength acrylic (PMMA) cement. Will also bond styrene, butyrate, polycarbonate, other plastics and porous surfaces.

16

Two-component Kit, reactive, high strength adhesive for bonding and fabricating all acrylics (extruded, cast, and cross linked PMMA) to each other. It will also bond acrylic to polyester, butyrate, PVC, ABS, PETG.

40

Two-component 10:1, reactive, high strength acrylic based adhesive provides ‘‘museum quality’’ water clear joints with excellent weather ability. Mil Spec A-8576C Type III.

42

VOC-free 1:1, two-component, slow-setting, reactive,urethane-based adhesive for bonding polycarbonate,butyrate, ABS, and PETG to themselves and each other. Excellent UV light resistance.

55

VOC-free 1:1, two-component, fast-setting, reactive,urethane-based adhesive for bonding polycarbonate,butyrate, ABS, and PETG to themselves and each other. Excellent UV light resistance.

58

DescriptionProduct

High Viscosity ethyl based ‘superglue’ for bonding where gap fill is important, or on absorbent surfaces such as wood, paper and some fabrics. Bonds most plastics, rubbers and metals.

CA01

A thixotropic ‘superglue’ gel. It is a non-drip formulation and will not run on vertical surfaces. It is fast to set on difficult surfaces such as leather and acetic substrates.

CA44

Thixotropic UV adhesive for bonding clear plastics to themselves, glass and metal. High Intensity Visible light cure is also possible.

UV106

Low odour 1:1, toughened clear acrylic adhesive. Bonds clear plastics, and other dissimilar materials. Low exotherm and shrinkage allow bonding of Alucabond without witness marks on face of panel.

3004-03

Low viscosity ‘superglue’ for use with special primer for bonding difficult plastics and elastomers such as PP, PE, Silicone, Glass-filled Nylon.

CA4061 Kit

Two-component 10:1 ‘Ultimate Plastic Bonder’ for bonding Polyolefin’s (P.P. & P.E.) to themselves, most other plastics and metals.

PPX5

Medium syrup, fast set, flexible bond. For flexible orrigid vinyl to itself or other materials such as leather,canvas, fabrics, ABS, acrylics, butyrate and polyurethane. Weather resistant.

4784

Low VOC, medium bodied, fast setting, cement for bonding ABS only.4707

www.scigrip.com

CHANGING THE WAY YOU PUT THINGSTOGETHER

SCIGRIP Smarter Adhesive Solutions™, is one of Europe’s leading manufacturers and formulators

of Engineering and Structural adhesives. Many of our patented formulations are used within the

automotive, marine and OEM sectorsaround the world.

The Sign and Display offer focuses on the adhesive technologies required to bond the wide range

of substrates typically found within the Sign and Display, shopfitting and plastic assembly markets.

Our 20 years’ experience in this market is based on the supply of quality products with first class

logistical and technical support.

Due to many potential variations in substrate and surface chemistries, SCIGRIP Adhesives and its distributors recommend that all substrates be tested under the intended applications to determine suitability.

SIGN AND DISPLAY SELECTION GUIDE

5558

4707

1642

165558

16425558

101645

45164245

423004

PPX5500010

30010

30010

30010

30010

30010

30041042

4547845558

5000-065000-065000-065000-06

1642

34SC1642

UV1061642

4245

1642

45164245

423004

PPX51045

1045

1045

1045

1045

1045

UV1063004

4245

45 4784Acrylic Sheet

ABS

5000-065000-065000-065000-06

165558

UV1061642

34SC4255

425558

101642

45164245

423004

PPX51045

1045

1045

1045

1045

1045

UV1063004

104245

45 10PETG

5000-065000-065000-065000-06

16425558

4245

425558

4SC42

101642

45164245

423004

PPX51045

1045

1045

1045

1045

104245

UV1063004

104245

45 10Polycarb

5000-065000-065000-065000-06

10164245

1642

101642

101642

1042

45164245

423004

PPX5500045

3001045

3001045

3001045

3001045

3001045

30042002

1042

45 4784PVC (Rigid)

5000-065000-065000-065000-06

165558

UV1061642

34255

425558

101642

45164245

3004 PPX51045

1045

1045

1045

1045

1045

UV1063004

104245

45 10PVC (Flexible)

5000-065000-065000-065000-06

45 45 45 45 4545

478445 3004 PPX5 45 45 45 45 45 45

20023004

45 45478445

PVC (Foam)

5000-065000-065000-065000-06

423004

423004

423004

423004

1042

3004

103004

103004

1042

3004

4245

PPX5

4245300

4245300

4245300

4245300

4245300

30043346

300420023346

300445

20023004Alucobond™

5000-065000-065000-065000-06

PPX5 PPX5 PPX5 PPX5 PPX5 PPX5 PPX5 PPX5 PPX5 PPX5 PPX5 PPX5 PPX5 PPX5 PPX5 PPX5 PPX5 PPX5 PPX5PE/PP

5000-065000-065000-065000-06

105000

1045

1045

1045

500045

1045

1045

3004 PPX53005000

3005000

3005000

3005000

3005000

3005000

UV1063004

33462002

45 10Fibreglass

(GRP)

5000-065000-065000-065000-06

30010

1045

1045

1045

3001045

1045

1045

32953004 PPX5

3005000

30032953346

30032953346

30032953346

30032953346

30032953346

33462002

1045

1045

10Aluminium

5000-065000-065000-065000-06

30010

1045

1045

1045

3001045

1045

1045

32953004 PPX5

3005000

30032953346

30032953346

30032953346

30032953346

30032953346

33462002

1045

1045

10Stainless Steel

5000-065000-065000-065000-06

30010

1045

1045

1045

3001045

1045

1045

32953004 PPX5

3005000

30032953346

30032953346

30032953346

30032953346

30032953346

33462002

1045

1045

10Mild Steel

5000-065000-065000-065000-06

30010

1045

1045

425558

3003295

1045

164245

3004 PPX53005000

30032953346

30032953346

30032953346

30032953346

30032953346

33462002

1045

1045

10Brass Sheet

5000-065000-065000-065000-06

30010

1045

1045

1045

3001045

1045

1045

3295

30043346

PPX53005000

30032953346

30032953346

30032953346

30032953346

30032953346

33462002

1045

1045

10PowderCoated

5000-065000-065000-065000-06

3004UV1063004

UV1063004

UV1063004

30042002

30042002

30042002

300420023346

PPX533462002

33462002

33462002

33462002

33462002

33462002

33462002

33462002

2002 2002Glass

5000-065000-065000-065000-06

1042

1042

UV1063004

UV1063004

30042002

30042002

30042002

30042002

PPX51045

1045

1045

1045

1045

1045

33462002

33462002

200210

2002Polyester

5000-065000-065000-065000-06

45 45 45 45 45 454510

453004

PPX5 451045

1045

1045

1045

1045

20021045

45 45Wood

5000-065000-065000-065000-06

47845558

4784 10 10 4784478445

4784 3004 PPX5 10 10 10 10 10 10 2002 10 4547845558

Polyurethane

ABS

PETG

Poly

ca

rb

PVC

(R

igid

)

PVC

(Fl

exi

ble

)

PVC

(Fo

am

)

Alu

co

bo

nd

™

PE/P

P

Fib

reg

lass

(G

RB)

Alu

min

ium

Sta

inle

ss S

tee

l

Mild

Ste

el

Bra

ss S

he

et

Pow

de

r Co

ate

d

Gla

ss

Poly

est

er

Wo

od

Poly

ure

tha

ne

Ac

rylic

Sh

ee

t

SCIGRIP Changing the way you put things together.

ADHESIVES FOR METALSDescriptionProduct

Two-component Kit, high strength, high viscosity structural adhesive for bonding PVC, acrylic, ABS, and polycarbonate. Also bonds well to steel, non-anodized aluminum, other metals.

10

Two-component 4:1, high strength, high viscosity,reactive structural adhesive for bonding unprepared and corrosion resistant metals, composites, wood, and plastics.

45

Two-component 10:1 MMA for bonding metals &composites. Most metals do not require a primer or surface preparation. Reduced odour and low read-through.

300 Series

A high specification clear MS Polymer adhesive. It is a single component system, with fast cure time and very high ultimate strength. Bonds and seals most materials. Paintable after cure.

2002

High Strength 1:1, low viscosity Toughened Acrylicbased adhesive. May be applied bead-on-bead or via mixer nozzle. Ideal for close fitting or ‘discrete’ bonds in stainless steel, aluminium and other metals.

3295-03

DescriptionProduct

No Mix System, Rubber Toughened Acrylic adhesive for use with brush on 7701 Initiator. Allows infinitely adjustable open time, but very rapid fixture on assembly.

3346 Kit


3004-03

High strength, two-component 1:1 MMA for bondingmetals, plastics and composites. Good gap-filling and low sag properties for a wide range of applications. Excellent tensile and impact strength.

5000 Series

A clear, two-component 1:1, non-yellowing, fast curing epoxy adhesive. This diverse adhesive can join a huge array of different materials, providing a high strength, water resistant bond.

6005

DescriptionProduct

High strength two-component 1:1 MMA for bonding metals, plastics and composites. Good gap-fi lling and low sag properties for a wide range of applications. Excellent tensile and impact strength.

5000 Series

Two-component 10:1 MMA for bonding metals &composites. Most metals do not require a primer or surface preparation. Reduced odour and low read-through.

300 Series


3004-03

DescriptionProduct

Two-component Kit, high strength, high viscositystructural adhesive for bonding PVC, acrylic, ABS,and polycarbonate. Also bonds well to steel, non-anodized aluminum, other metals.

10

A clear, two-component 1:1, non-yellowing, fast curing epoxy adhesive. This diverse adhesive can join a huge array of different materials, providing a high strength, water resistant bond.

6005

A high specifi cation clear MS Polymer adhesive. It is a single component system, with fast cure time and very high ultimate strength. Bonds and seals most materials. Paintable after cure.

2002

ADHESIVES FOR COMPOSITES

ADHESIVES FOR GLASSDescriptionProduct

No Mix System, Rubber Toughened Acrylic adhesive for use with brush on 7701 Initiator. Allows infi nitely adjustable open time, but very rapid fi xture on assembly.

3346 Kit


3004-03

DescriptionProduct

Thixotropic UV adhesive for bonding clear plastics tothemselves, glass and metal. High Intensity Visible light cure is also possible.

UV106

A high specification clear MS Polymer adhesive. It is a single component system, with fast cure time and very high ultimate strength. Bonds and seals most materials. Paintable after cure.

2002

CLEANERS, PRIMERS AND INITIATORSDescriptionProduct

Used in combination with CA4061 or other ‘superglue’ to promote adhesion on low energy surfaces such as Polyethylene, Polypropylene, Silicone rubber and certain hard to bond materials.

A701

A non-flammable, solventless initiator to be used in conjunction with our 3346 No-mix acrylic adhesive. 7701 ensures a rapid fi xture time once parts are assembled and is also available in a slower version - 7705.

7701

DescriptionProduct

A multi-purpose plastics cleaner for acrylics,polycarbonate, butyrate, vinyl, ABS, Styrene.

Powerful Solvent Cleaner/Degreaser.A061

57

Other products available on request

ViscosityReference

Typicalviscosity (cps)

Typicalspecificgravity

WorkingTime

PackagingProduct ColourTechnologyFixtureTime

N/A1.302 min1 min1 Litre Tin#ClearAcrylic3 water-thin

N/A1.123 min1-2 min1 Litre Tin#ClearSolvent4SC water-thin

40,0001.031-2 hrs25 min473ml Kit#WhiteMMA10 ketchup

1,0001.035-6 min2-3 min473ml Tin#ClearAcrylic16 motor oil

2,9001.032 hrs20 min473ml Kit#ClearMMA40 syrup

2,9001.032 hrs15 min50ml Cart#ClearAcrylic42 syrup

4,0001.141-2 hrs5-6 min50ml Cart#ClearUrethane55 syrup

4,0001.1420 min2-3 min50ml Cart#ClearUrethane58 syrup

1,5001.0660 sec10 sec50g Bottle#ClearCyanoacrylateCA01 motor oil

50,0001.0660 sec10 sec20g TubeClearCyanoacrylateCA44 gel

5,0001.09< 30 secN/A50ml Bottle#ClearAcrylic - UV Cureduv106 syrup

25,0000.99< 5 min< 3 min50ml Cart#ClearToughened Acrylic3004-03 gel

201.062 secsN/A20g Bottle#ClearCyanoacrylateCA4061 KIT water-thin

6,5000.99> 15 min4-6 min50ml Cart#WhiteMMAPPX5 syrup

3350.9025-30 min20 min473ml Tin#ClearSolvent4784 motor oil

4,0000.8810-15 min10 min473ml Tin#MilkySolvent4707 syrup

ViscosityReference



WorkingTime



500,0001.0515 min6 min400ml Cart#TanMMA45 peanut butter

250,0001.02VariousVarious50ml & 490mlOff White•MMA300 Series peanut butter

N/AN/A24 hrs20 min290ml CartClearMS Polymer2002 mastic

3,5001.026 min2 min25ml, 50ml#Pink & GreenToughened Acrylic3295-03 syrup

30,000N/A< 90 sec< 30 sec300ml Tube#ClearToughened Acrylic3346 Kit N/A

120,0000.97VariousVarious25ml, 50ml & 400mlAmberMMA5000 Series peanut butter

50,0001.210-12 min3-4 min50ml CartClearEpoxy6005 syrup

ViscosityReference



WorkingTime


30,0001.04< 90 sec< 30 sec300ml Tube#Pale AmberToughened Acrylic3346 Kit ketchup


5,0001.09< 30 secN/A50ml Bottle#ClearAcrylic - UV CuredUV106 syrup

N/AN/A24 hrs20 min290mlClearMS Polymer2002 mastic

ViscosityReference



WorkingTime


N/AN/AN/AN/A400ml AerosolClearCleaner/DegreaserA061 water-thin

N/A0.81N/AN/A500ml Tin#ClearPlastic Cleaner57 water-thin

N/AN/AN/AN/A50ml Pump SprayClearCA PrimerA701 water-thin

N/AN/A< 2 min< 1 min18ml & 35ml Bottle#Clear3346 Initiator7701 water-thin

ViscosityReference



WorkingTime


120,0000.97VariousVarious25ml, 50ml & 400AmberMMA5000 Series peanut butter

250,0001.02VariousVarious50ml & 490mlOff White•MMA300 Series peanut butter



50,0001.210-12 min3-4 min50ml CartClearEpoxy6005 syrup

N/AN/A24 hrs20 min290ml CartClearMS Polymer2002 mastic

# Other pack sizes are available please enquire • Also available in black

© 2012 - SCIGRIP® Smarter Adhesive Solutions. All rights reserved.

SCIGRIP EuropeUnit 22, Bentall Business Park, Glover Road,Washington, Tyne and Wear, NE37 3JD. United KingdomTel: +44 (0) 191 419 6444Fax: +44 (0) 191 419 6445Email: [email protected]

www.scigrip.com

Your distributor:The information contained herein is produced in good faith, and is believed to be reliable but is for guidance

only. SCIGRIP and its agents cannot assume liability or responsibility for results obtained in the use of its products

by persons whose methods are outside or beyond our control. All advice is given subject to terms & conditions of

sale, which are available on request from SCIGRIP. It is the users responsibility to determine the suitability of any of

the products and methods of use or preparation prior to use mentioned in our literature and furthermore it is the

user’s responsibility to observe and adopt such precautions as may be advisable for the protection of personnel

and property in the handling and use of any of our products. SCIGRIP reserves the right to change specifications

& prices without notice and customers should satisfy themselves that information relied on by the customer is that

which is currently published by the company on its website.

FURTHER SMARTER ADHESIVE SOLUTIONS AVAILABLE FROM SCIGRIP:

SCIGRIP’s well established range of REACH compliant engineering, maintenance, adhesives and sealants has grown and developed with the OEM and MRO industrial sectors over the past 3 decades. This division is a highly accredited sector of the SCIGRIP European Group, with WRAS, AGA, ASTM, NSF, DVGW, MIL specifications available for many of the products.

THE RANGE INCLUDES;

• ANAEROBICS - THREADLOCKERS - RETAINERS - SEALANTS & GASKET MAKERS• CA-INSTANT ADHESIVES• RTV SILICONES - POWERCAN PACKAGING• EPOXY STICKS AND REPAIR COMPOUND• ACTIVATORS AND PRIMERS• UV ADHESIVES

SCIGRIP offers cutting edge formulations of Methacrylate adhesives that are unrivalled for their combination of strength, toughness and ease of use.

This highly accredited range of products successfully services the Marine, Transportation, Building & Construction, Renewable Energy and Recreational Vehicle sectors.

THE RANGE COVERS;

• VARIED OPEN TIMES• 0.5MM - 39MM GAP FILL• PRIMERLESS METAL BONDING• CLEAR MMA• PE AND PP BONDING• HIGH PEEL AND HIGH FATIGUE RESISTANCE• HIGH TOUGHNESS AND ELONGATION• MARINE APPROVALS

HOLDTITE ENGINEERING STRUCTURAL ADHESIVES

S&D03/12

sign and display adhesive - hawaii’s acrylic fabricator...science + innovation = smarter adhesive...

Documents