Edge-Trim is a self-contained shear slitting system specifically

designed for trimming the edges of a continuously moving flexible web.

Instead of expensive cross-web hardware, this unique system has both upper

slitter and driven anvil ring mounted on a common C-Frame on linear rails.

Setup time is virtually eliminated because the blade-to-anvil geometric

relationship is never disturbed during slitting repositioning.

Optional Automated Controls are available for applications where trim

width accuracy is critical, where access to the trim slitters is difficult, or

where ‘on the fly’ trim changes or adjustments to the position of the

knives are required.

Optional Automated Controls• User-friendly, intuitive operations and touch-screen controls

• Highly accurate absolute web width patterns

• Absolute incremental positioning

• Position accuracy of ± .008" (0.2 mm)

Self-Contained Shear Slitting SystemEdge-TrimEdge-TrimTM

KEY

FEAT

UR

ES

Key Features:• Advanced design allows for trim

changes and blade replacements‘on the fly’, reducing downtimeand waste

• Built tough for reliable operations inmill-duty/heavy-duty environments

• Automatically maintains criticalblade-to-anvil relationship, greatlyreducing setup time while ensuringtrimming accuracy

• C-Frame allows trim up to 6.6", withmaximum possible trim of 15”

• Modular and flexible for a widerange of operations

• Compact and rugged control consoleenables many mounting options

• Can be configured to run from PCvia stand-alone program or existingHuman Machine Interface(RsView32, Wonderware, etc.)

Design Features

12.625(320.6)

30.6

39

12.331

(313.2)

(778

.2)

25.1

87

(639

.7)

5.000(127)

5.750(146.0)

15.707(399.0)

35.2

30

29.8

13

14.408(366.0)

(894

.8)

(757

.3)

Standard Edge-Trim Assembly

Class III Knifeholders

Class II Knifeholders

Specifications

Simplified Connections- Requires only 110 (or 220) VAC single-phase power and two easy-to-wire interconnect lines between the touchscreen

control and edge trim units. Input air connections are (also) required for the knife control and pneumatic brakes

- RS-485 communication and 24 VDC power cables

Servo System- True servo system with incremental encoder and DC brushless servomotors

Touch Screen- Industrial touch screen controller with NEMA 4 / IP65 enclosure

Control Console- Compact and rugged control console enables many mounting options

Anvil Motors- Ziehl-Abegg 3-phase External-Rotor-AC dust sealed motors enable a wide range of operating speeds and torque

values. Gear reducers are available for slow speed applications.

Construction- Heavy duty steel construction with non-corrosive nickel plated finish

Knifeholders- Performance Series Class II and Class III

Carriage Design- Modular mounts (bottom and back mount available), linear bearings, upper and lower blades are connected

Trim Widths- Standard trim support 5.6” (14.22 cm) (narrower and wider supports are available) - Maximum trim of 15” (38.1 cm) possible

Actuator- Self contained lead screw actuator with servomotor

Can be configured to run from customer’s PC via stand-alone program or an existing Human Machine Interface(RsView32, Wonderware, etc.)

Electrical

Mechanical

Options

Product Sheet: Edge-Trim 6.06

Complementary Products:TIDLAND

Slitting Products & Systems- Performance Series Knifeholders

Winding Products- Air Chucks- Boschert Safety Chucks

FIFEGuiding Products & Systems

MAGPOWR Tension Control ProductsTorque Control Products

Design Features

NomenclatureAutomated Edge-Trim

1. Performance Series Knifeholder2. Optional Platen Trim Support3. Edge Trim Unit4. AC Motor Drive5. Linear Bearing Rail6. Cable Management7. Sealed Linear Actuator8. Servo Motor

1

2

8

7

65

4

3

©20

06Ma

xces

sInt

erna

tiona

l

Tidland Corporation2305 SE 8th AvenueCamas, WA 98607, USAPhone: 360-834-2345Fax: 360-834-5865E-mail: tidland@tidland.comWeb: www.tidland.com

Maxcess EuropeFifestrasse 1, D-65779Kelkheim/Ts., GermanyPhone: (49) 6195-7002-433Fax: (49) 6195-7002-933E-mail: info@maxcess.de

Maxcess Asia300 Orchard Road No. 15-05Orchard TowersSingapore 238875Phone: (65) 6834-1998Fax: (65) 6835-4818E-mail: asia@maxcessintl.com