sealing the engine n chapter 5 n classroom manual –page95 n lab manual –page 113 cbc automotive...

14
SEALING the ENGINE Chapter 5 Classroom Manual – Page95 Lab Manual – Page 113 CBC AUTOMOTIVE RK

Upload: jonas-chase

Post on 30-Dec-2015

218 views

Category:

Documents


4 download

TRANSCRIPT

Page 1: SEALING the ENGINE n Chapter 5 n Classroom Manual –Page95 n Lab Manual –Page 113 CBC AUTOMOTIVE RK

SEALING the ENGINE

Chapter 5 Classroom

Manual– Page95

Lab Manual– Page 113

CBCAUTOMOTIVE

RK

Page 2: SEALING the ENGINE n Chapter 5 n Classroom Manual –Page95 n Lab Manual –Page 113 CBC AUTOMOTIVE RK

OBJECTIVES Locate cracks in castings. Explain process of repairing cracks by

welding. Properly install common engine gaskets

including cyl. head & valve cover gaskets. Properly install typical lip seals. Extract broken fasteners. Perform thread repair.

CBCAUTOMOTIVE

RKPage 113

Page 3: SEALING the ENGINE n Chapter 5 n Classroom Manual –Page95 n Lab Manual –Page 113 CBC AUTOMOTIVE RK

INTRODUCTION

Cracked castings - Repair or Replace? Other causes of leakage,

– Worn or damaged seals– Gaskets

Threaded holes can be damaged from,– Improper torquing– Corrosion CBC

AUTOMOTIVERKPage 113

Page 4: SEALING the ENGINE n Chapter 5 n Classroom Manual –Page95 n Lab Manual –Page 113 CBC AUTOMOTIVE RK

CRACK DETECTION

Visual Inspection Magnetic Particle Inspection (MPI) Magnetic Fluorescent Spray Penetrant Dye Pressure Testing

– On-car– Off-car

CBCAUTOMOTIVE

RKPage 114

Page 5: SEALING the ENGINE n Chapter 5 n Classroom Manual –Page95 n Lab Manual –Page 113 CBC AUTOMOTIVE RK

CRACK REPAIR

Pinning Cracks Welding Cracks Chemical Crack Repair

– Ceramic block sealers– Epoxy

CBCAUTOMOTIVE

RKPage 115

Page 6: SEALING the ENGINE n Chapter 5 n Classroom Manual –Page95 n Lab Manual –Page 113 CBC AUTOMOTIVE RK

GASKET INSTALLATION

Follow instructions. Thoroughly clean the mating surface. Match to old gasket. Check for proper fit. Never reuse gaskets.

CBCAUTOMOTIVE

RKPage 118

Page 7: SEALING the ENGINE n Chapter 5 n Classroom Manual –Page95 n Lab Manual –Page 113 CBC AUTOMOTIVE RK

CYLINDER HEAD GASKET

Must be capable of withstanding tremendous heat and pressure.

Follow gasket makers instructions on whether or not to use sealant.

What type of sealant and how much? Run thread chaser in bolt holes.

CBCAUTOMOTIVE

RKPage 119

Page 8: SEALING the ENGINE n Chapter 5 n Classroom Manual –Page95 n Lab Manual –Page 113 CBC AUTOMOTIVE RK

USING STRAIGHTEDGE

CBCAUTOMOTIVE

RK

Page 9: SEALING the ENGINE n Chapter 5 n Classroom Manual –Page95 n Lab Manual –Page 113 CBC AUTOMOTIVE RK

VALVE COVER GASKETS

Check cover flanges for straightness. Use load spreaders when available. Use sealants only when necessary and

not to much. See P5-8

CBCAUTOMOTIVE

RKPage 120

Page 10: SEALING the ENGINE n Chapter 5 n Classroom Manual –Page95 n Lab Manual –Page 113 CBC AUTOMOTIVE RK

SEAL INSTALLATION

Install with lip (and garter spring) toward liquid.

Lubricate lip before installation. Use sealant on the outside of steel

seals. Use a seal installer.

CBCAUTOMOTIVE

RKPage 122

Page 11: SEALING the ENGINE n Chapter 5 n Classroom Manual –Page95 n Lab Manual –Page 113 CBC AUTOMOTIVE RK

USING SEALANTS

Use proper sealant for application. Do not use sealants unless specified in

service manual or by gasket manufacturer.

Types of sealants– Hard drying– Aerobic (RTV)– Anaerobic

CBCAUTOMOTIVE

RKPage 122

Page 12: SEALING the ENGINE n Chapter 5 n Classroom Manual –Page95 n Lab Manual –Page 113 CBC AUTOMOTIVE RK

FASTENERS

ID fasteners by– Nominal diameter– Pitch (Threads per

Inch)– Length– Strength

CBCAUTOMOTIVE

RK

Page 13: SEALING the ENGINE n Chapter 5 n Classroom Manual –Page95 n Lab Manual –Page 113 CBC AUTOMOTIVE RK

THREAD REPAIR

See Handout

CBCAUTOMOTIVE

RK

Page 14: SEALING the ENGINE n Chapter 5 n Classroom Manual –Page95 n Lab Manual –Page 113 CBC AUTOMOTIVE RK

THREAD REPAIR

See Handout

CBCAUTOMOTIVE

RK