scope of work notes - home | mta

E-2005A

NOV 24, 2003

DATE :

DRAWING NO.

I:\standards\electrical\e-2005a.dgn 06-MAR-2020 14:43 kwunPRINT AS OF

DRAWN BY

DESIGNED BY

CHECKED BY

APPROVED BY

MANAGEMENT

CAPITAL PROGRAM

DEPARTMENT OF

(SIGNED)

STANDARD DRAWING

ELECTRICAL ENGINEERING

S. PIERI

E. DIAZ

S. SHAH, P.E.

G. REVES, P.E.

(SIGNED)

(SIGNED)

(SIGNED)ISSUE

FBSEB

PLB/ USED AS TEMPORARY SOURCE

NEW OR EXISTING SERVICE

60HZ

M

SEE NOTE 10

DBN

2P

600VNOTE 16

ATS

ATS

AC/DC

1P

NOTE 3

120/208VAC

600VDC120/208VAC

AC/DC LOADS

TO EXISTING 600V

TO EXISTING SERVICE

120/208VAC

60HZ

M

DBR120/208VAC

2P

NOTE 10

600V

1P

NOTE 16

ATS-GL

DB-GL

120/208VAC

NOTE 11

2.

3.

5.

6.

STENCIL THE TEMPORARY EQUIPMENT FOR IDENTIFICATION.

7.

DOORS. USE LAST FOUR DIGITS OF CONTRACT.

PROVIDE COMBINATION PADLOCKS FOR ALL EQUIPMENT AND ENTRANCE

8.

LOADS AT THE STATION.

THE TEMPORARY SERVICES SHALL BE RATED TO CARRY ALL ELECTRICAL

9.

10.

A. STATION LIGHTING (SPLIT WIRED)

D. VENT FANS (TO FAN ATS)

TYPICAL LOADS ON DISTRIBUTION BOARD DB-GL ARE:11.

A. AFC

B. TOKEN BOOTHS

C. LUBE ROOMS

D. EDR LIGHTING/POWER

E. CREW QUARTERS

F. COMMUNICATIONS

G. SIGNAL TOWER: DISPATCHER'S OFFICE

H. ESCALATOR ROOMS

12.

13. CIRCUIT BREAKER AS PER SIGNAL STANDARDS.

14. PROVIDE 30% SPACE CAPACITY IN EACH CIRCUIT BREAKER PANEL.

15.

16.

E.D.R.s. AND TEMPORARY POWER ENCLOSURES.

EMT CONDUIT SHALL BE USED FOR ALL TEMPORARY WIRING OUTSIDE OF

ENCLOSURES.

EACH TEMPORARY AND PERMANENT SERVICE SHALL BE IN SEPARATE

INFRASTRUCTURE.

STATIONS AT A TIME IN CONSULTATION WITH THE DIVISION OF OF

TEMPORARY ELECTRIC SERVICE SHALL BE LIMITED TO A MAXIMUM NUMBER

SERVICE AT ONE TIME.

ONLY ONE EXISTING SERVICE SHALL BE CONVERTED TO TEMPORARY

B. PUMPS (TO PUMP ATS)

C. ELEVATORS (TO ELEVATOR ATS)

LOAD, NOTE 13

TO SIGNAL

A MAXIMUM OF TWO HOURS DURING OFF-HOURS.

FOR SCHEDULED INTERRUPTIONS OF ONE OF THE 60HZ SERVICES FOR

PROVIDING TWO 60 HZ AND ONE DC SOURCE AT ALL TIMES EXCEPT

ALL THE EXISTING TUNNEL, STATION AND CONCESSION LOADS BY

TO PERFORM THE WORK NECESSARY TO MAINTAIN ENERGIZATION OF

THOSE SHOWN ARE:

TYPICAL LOADS ON DISTRIBUTION BOARDS DBN OR DBR OTHER THAN

DIAGRAM IND DIVISION

FOR STATIONS - ONE LINE

TYPICAL TEMPORARY POWER

FROM OUTSIDE THE ENCLOSURE OR ROOM.

PROVIDE AN UNFUSED DISCONNECT SWITCH WHEN THE FEEDER COMES

E-2000 GENERAL NOTES FOR SUBWAYS AND ELEVATED LINES

SCOPE OF WORK

NOTES

ONE LINE DIAGRAM

E-2001 ELECTRICAL SYMBOLS

1.

2.

3.

1.

4.

PERMITTED.OF THE WORK. MOUNTING ON THE TILE WALLS IS NOT

CEILING ONLY. RESTORE THE FLOOR AND CEILING AFTER THE COMPLETION

EQUIPMENT ON KINDORF. SECURE THE KINDORF TO THE FLOOR AND

ENCLOSURE APPROVED BY THE ENGINEER. MOUNT THE TEMPORARY

THE CONTRACTOR SHALL PROVIDE A LOCKABLE TEMPORARY POWER

E.D.R./TEMPORARY POWER ENCLOSURE.

ENCLOSURES SHALL BE USED TO HOUSE EQUIPMENT OUTSIDE OF THE

TO BE INSTALLED THROUGH THE BOTTOM OF THE ENCLOSURE. NEMA 12

BE NEMA 1 WITH ADEQUATE GUTTER SPACE FOR ALL CABLE. ALL ENTRIES

ALL EQUIPMENT IN TEMPORARY POWER ENCLOSURES AND E.D.R.s. SHALL

(NEC).

PROVIDED IN ACCORDANCE WITH THE NATIONAL ELECTRICAL CODE

PROVIDE A GROUND WIRE IN ALL EMT CONDUITS. GROUNDING SHALL BE

ELEVATED LINES

E-2020 TYPICAL GROUNDING OF ELECTRICAL EQUIPMENT SUBWAYS AND

REFERENCES

SERVICE FOR THE AC/DC ATS IS 600V-60HZ.

ACCEPTING 600V-60HZ, 600V-25HZ AND 600VDC SOURCES. NORMAL

THE AC/DC AUTOMATIC TRANSFER SWITCH (ATS) SHALL BE CAPABLE OF

LOAD, NOTE 13

TO SIGNAL

DIAGRAM IRT/BMT DIVISION

FOR STATION - ONE LINE

TYPICAL TEMPORARY POWER

E-2005B

NOV 24, 2003

DATE :

DRAWING NO.

I:\standards\electrical\e-2005b.dgn 06-MAR-2020 14:44 kwunPRINT AS OF

DRAWN BY

DESIGNED BY

CHECKED BY

APPROVED BY

MANAGEMENT

CAPITAL PROGRAM

DEPARTMENT OF

(SIGNED)

STANDARD DRAWING


S. PIERI

E. DIAZ

S. SHAH, P.E.

G. REVES, P.E.

(SIGNED)

(SIGNED)

(SIGNED)ISSUE

FB 600VDCPLB/

SEB

M

SWN

NOTE 15

600V 1P

NOTE 16

ATS

ATS

AC/DC

NOTE 3

TO EXISTING 600V

AC/DC LOADS

PLB/

SEB

M

SWR

600V

1P

ATS-GL

DB-GL

120/208VAC

NOTE 10

LOAD, NOTE 12

TO SIGNAL

1.

ENCLOSURES.

EACH TEMPORARY AND PERMANENT SERVICE SHALL BE IN SEPARATE

E.D.R.s. AND TEMPORARY POWER ENCLOSURES.

EMT CONDUIT SHALL BE USED FOR ALL TEMPORARY WIRING OUTSIDE OF 2.

3.

PARTICULAR STATION.AS THE FIRST WORK TO BE DONE AT A

CONTRACTOR SHALL INSTALL THE NEW PERMANENT SECOND SOURCE

THOSE STATIONS THAT HAVE ONLY ONE SOURCE OF AC POWER THE

SERVICES FOR A MAXIMUM OF TWO HOURS DURING OFF-HOURS. FOR

EXCEPT FOR SCHEDULED INTERRUPTIONS OF ONE OF THE 60HZ

PROVIDING TWO AC SOURCES AND ONE DC SOURCE AT ALL TIMES

ALL THE EXISTING TUNNEL, STATION AND CONCESSION LOADS BY

TO PERFORM THE WORK NECESSARY TO MAINTAIN ENERGIZATION OF

THE AC/DC ATS IS 600V-60HZ.

ACCEPTING 600V-60HZ AND 600VDC SOURCES. NORMAL SERVICE FOR

THE AC/DC AUTOMATIC TRANSFER SWITCH (ATS) SHALL BE CAPABLE OF

4.

5. STENCIL THE TEMPORARY EQUIPMENT FOR IDENTIFICATION.

6.

7.

DOORS. USE LAST FOUR DIGITS OF CONTRACT.

PROVIDE COMBINATION PADLOCKS FOR ALL EQUIPMENT AND ENTRANCE

8.

LOADS AT THE STATION.

THE TEMPORARY SERVICES SHALL BE RATED TO CARRY ALL ELECTRICAL

9.

INFRASTRUCTURE.

OF STATIONS AT A TIME IN CONSULTATION WITH THE DIVISION OF

TEMPORARY ELECTRIC SERVICE SHALL BE LIMITED TO A MAXIMUM NUMBER

10. TYPICAL LOADS ON DISTRIBUTION BOARD DB-GL ARE:

A.

B.

C.

D.

E.

F.

G.

H.

I.

J.

K.

L.

TOKEN BOOTHS

LUBE ROOMS

EDR LIGHTING/POWER

CREW QUARTERS

STATION LIGHTING (120V)

SIGNAL TOWER: DISPATCHER'S OFFICE

COMMUNICATIONS

PUMPS

ESCALATORS

ELEVATORS

VENT FANS

11.

PROVIDED IN ACCORDANCE WITH THE NATIONAL ELECTRICAL CODE (NEC).

PROVIDE A GROUND WIRE IN ALL EMT CONDUITS. GROUNDING SHALL BE

12. CIRCUIT BREAKER AS PER SIGNAL STANDARDS.

13. PROVIDE 30% SPACE CAPACITY IN EACH CIRCUIT BREAKER PANEL.

14.

SERVICE AT ONE TIME.

ONLY ONE EXISTING SERVICE SHALL BE CONVERTED TO TEMPORARY

15.

16.

FROM OUTSIDE THE ENCLOSURE OR ROOM.

PROVIDE AN UNFUSED DISCONNECT SWITCH WHEN THE FEEDER COMES

E-2000 GENERAL NOTES FOR SUBWAYS AND ELEVATED LINES

E-2001

E-2020

ELECTRICAL SYMBOLS

LINESELEVATED

TYPICAL GROUNDING OF ELECTRICAL EQUIPMENT SUBWAYS AND

AFC

SCOPE OF WORK

NOTES

REFERENCES

ONE LINE DIAGRAM

1.

2.

3.

OF THE WORK. MOUNTING ON THE TILE WALLS IS NOT PERMITTED.

CEILING ONLY. RESTORE THE FLOOR AND CEILING AFTER THE COMPLETION

EQUIPMENT ON KINDORF. SECURE THE KINDORF TO THE FLOOR AND

ENCLOSURE APPROVED BY THE ENGINEER. MOUNT THE TEMPORARY

THE CONTRACTOR SHALL PROVIDE A LOCKABLE TEMPORARY POWER

E.D.R.

ENCLOSURES SHALL BE USED TO HOUSE EQUIPMENT OUTSIDE OF THE

TO BE INSTALLED THROUGH THE BOTTOM OF THE ENCLOSURE. NEMA 12

BE NEMA 1 WITH ADEQUATE GUTTER SPACE FOR ALL CABLE. ALL ENTRIES

ALL EQUIPMENT IN TEMPORARY POWER ENCLOSURES AND E.D.R.s. SHALL

(REINFORCE IF NECESSARY)

120/208V, 60HZ

NEW OR EXISTING SERVICE

LOAD, NOTE 12

TO SIGNAL

PROVIDE A FUSED DISCONNECT SWITCH IF REQUIRED.

CT CABINET

LINE SIDE

CABINET

CURRENT TRANSFORMER

CT CABINET

LOAD SIDE

NOTE 8

NOTE 5

IS

OL

AT

ED

LN

LD

SWITCH

SERVICE

NOTE 3

CONNECTION, TYP.

STRUCTURAL STEEL

DETAIL B

NOTE 8,9

CONDUCTOR

GROUNDING

EQUIPMENT

BUSHING

GROUNDING

INSULATED

NOTE 7

JUMPER

BONDING

WALL

ENCLOSURE

EQUIPMENT

HUB

WATERTIGHTLOCKNUT

NOTE 14

BUSHING

INSULATED GROUNDING

NEUTRAL

SIDE OF COLUMN

ON SIDEWALK

SERVICE END BOX

SERVICE CONDUIT

LEVEL

SIDEWALK

18" MINIMUM

PEDESTAL

CONCRETE

LEVEL

STREET

CONNECTOR

PARALLEL TAP

(NOTE 6)

OR LESS

1100

1100

OVER

OR LESS

500

CONDUIT SIZE (INCH)

1/0 2/0 4/0

1 211 2

12

100 200 500 800 1000 1600 2000 2500 4000

1/0 2/0 4/0 250 350 500

20 60

12 10 8 6 2

NOTES

LEGEND

NOT TO SCALE

GROUND BUS - NOTE 14

ISOLATED NEUTRAL BUS

BONDING LOCKNUT

INSULATED THROAT WITH

WATERTIGHT HUB,

TWO HOLE TYPE

SOLDERLESS COPPER LUG

NOTE 6

CONDUCTOR

ELECTRODE

GROUNDING

NOTE 12

STRUCTURAL STEEL

DRILL AND TAP

GROUNDING LUG

(NTS)

IN ELECTRIC SERVICE ROOM, TYP

EQUIPMENT GROUNDING AND BONDING

SERVICE CONDUIT ON ELEVATED LINES

DETAIL C (NTS)ENCLOSURE BONDING

DETAIL B (NTS)

LESS

250 OR

6 4 2

(AWG OR KCMIL)

OR EQUIVALENT AREA FOR PARALLEL CONDUCTORS

SIZE OF LARGEST SERVICE ENTRANCE CONDUCTOR

COPPER WIRE (AWG)

SIZE OF GROUNDING ELECTRODE CONDUCTOR

43

43

43

CON EDISON NEUTRAL

G

G

N

G

G

G

G

G

GG

LINE BOX

PROPERTY

LESS

1/0 OR

G

N

STRAP

SUPPORT

CONDUITSTEEL COLUMN

STRUCTURAL

G

N

G

NTS

TABLE A: GROUNDING ELECTRODE CONDUCTOR

TABLE B: EQUIPMENT GROUNDING/BONDING CONDUCTOR

NOTE 8

CONDUCTOR

GROUNDING

EQUIPMENT

LUGS, TYP

GROUNDING

TYP

NOTE 8,9

300

4

NOT EXCEEDING (AMPERES)

AHEAD OF EQUIPMENT

OVERCURRENT DEVICE IN CIRCUIT

AMPERE RATING OR SETTING OF

(AWG OR KCMIL)

CONDUCTOR - COPPER

SIZE OF EQUIPMENT GROUNDING

NOTE 13

FIRST MOUNTING CLAMP

INSTALLED BEFORE

INSULATING COUPLING

CONDUIT

RIGID

208/120VAC, 3PH, 4W

CON EDISON COMPANY

PANELBOARD

NOTE 5 NOTE 5

NOTE 8,9 NOTE 8,9

G G

N N

PANELBOARD, ETC.

DISTRIBUTION BOARD,

LESS

2/0 OR

NOTE 7

JUMPER

BONDING

TRANSFER SWITCH

PANELBOARDS OR

DISTRIBUTION BOARDS,

NOTE 5

IN

OT

HE

R

RO

OM

S,

NO

TE

10

TO

EL

EC

TRI

CA

L

EQ

UI

PM

EN

T

TO

EL

EC

TRI

CA

L

DE

VI

CE

S,

NO

TE

10

G

G

G

G

CONDUCTORS, NOTE 6

GROUNDING ELECTRODE

(METAL ONLY)

CONDUIT

STEEL

STRUCTURAL

FR

OM

EL

EC

TRI

C

SE

RVI

CE

RO

OM

DATE :

DRAWING NO.

DRAWN BY

DESIGNED BY

CHECKED BY

APPROVED BY

MANAGEMENT

CAPITAL PROGRAM

DEPARTMENT OF

STANDARD DRAWING


ISSUE

G

SEE NOTE 18

CONNECTOR

PARALLEL TAP

WITH MULTIPLE CONDUIT

JUNCTION BOX

(METAL ONLY)

(SIGNED)

(SIGNED)

(SIGNED)

(SIGNED)

E-2020

G

NOV 24, 1993

1" C.

1 1/2"C.

2 1/2"C.

3"C.

4"C.

3/4"C.

1"C.

3/4"C.

1 1/2"C.

2 1/2"C.

3"C.

4"C.

NOTE 5

SEE

(NOTES 5,8,10)

BONDING JUMPER

E. DIAZ

EGC (TYPICAL)

(TYPICAL) SEE NOTE 5

BONDING JUMPER

LINK IN SERVICE SWITCH

NEUTRAL DISCONNECT

CONDUCTOR

GROUNDING ELECTRODE

CONDUCTOR (EGC)

EQUIPMENT GROUNDING

GROUNDING BUSHING

INSULATED THREADED

SPECIFICATION GRADE

CONDUIT

WITH SINGLE

JUNCTION BOX

STEEL CONNECTION

DETAIL A (NTS) STRUCTURAL

CONDUCTORS, NOTE 6

GROUNDING ELECTRODE

SEE NOTE 3

DETAIL A

(SEE NOTE 3 & 4)

JUNCTION BOX

T-CONDULET/

COATED STEEL CONDUIT

USE POLYURETHANE

STEEL AND REBARS.

FROM STRUCTURAL

ELECTRICALLLY

ISOLATE CONDUIT

S. PIERI

S. SHAH, P.E.

G. REVES, P.E.

(NTS)

IN ROOMS WITHOUT EGC, TYP

EQUIPMENT GROUNDING AND BONDING

DETAIL A

SEE NOTE 4

R:\61465\grand_street\ele\standards\e-2020 rev g.dgnR:\61465\grand_street\ele\standards\e-2020 rev g.dgn 07-JAN-2020 12:21 sandraPRINT AS OF

REFER TO STANDARD DRAWING E-2021 FOR OTHER TYPICAL GROUNDING DETAILS.20.

INSTALLED IN THE EDR FOR EQUIPMENT GROUNDING.

WHERE STRUCTURAL STEEL IS NOT AVAILABLE, THE GROUND BUS BAR SHALL BE 19.

EGC SHALL BE TAPPED AND CONNECTED TO PULL BOX GROUND BUS.

WHERE THE BONDING JUMPER SHALL BE IN ACCORDANCE WITH TABLE "B". THE LARGEST

RACEWAYS (DEPENDING ON NUMBER OF RACEWAYS AND SIZES)IN THE PULL BOXES

COMMON CONTINUOUS EQUIPMENT BONDING JUMPER SHALL CONNECT TWO OR MORE18.

BUS IN COMM. POWER PANEL AND THE MASTER BONDING BAR (MBB) IN THE COMM. ROOM.

POWER PANEL IN COMM. ROOM. A GROUND CONNECTION SHALL BE MADE WITH THE GROUND

CONDUCTOR SHALL BE INSTALLED ALONG WITH CIRCUIT CONDUCTORS TO COMMUNICATION

DRAWING W-1079B AND SPECIFICATION SECTION 19 CRBG. AN EQUIPMENT GROUNDING

FOR GROUNDING IN COMMUNICATION ROOM REFER TO COMMUNICATION STANDARD 17.

FOR TRANSFORMER GROUNDING SEE STANDARD DRAWING E-2022. 16.

A SEPARATE EGC SHALL BE PROVIDED.

TROUGH GROUNDING AND BONDING SHALL BE AS RECOMMENDED BY THE MANUFACTURER. 15.

BE KEPT CLEAN DURING PAINTING.

BE WELDED TO THE ENCLOSURE BEFORE GALVANIZING. THE CONTACT SURFACE SHALL

BOLTED ON CLEAN SURFACE OF SUITABLY SIZED STEEL BRACKET. THE BRACKET SHALL

AUTOMATIC TRANSFER SWITCHES, AND SAFETY SWITCHES. THE GROUND BUS SHALL BE

IN ALL METAL JUNCTION BOXES, SWITCHBOARDS, DISTRIBUTION BOARDS, PANELBOARDS,

PROVIDE COPPER EQUIPMENT GROUND BUS OF PROPER SIZE AND QUANTITY OF LUGS14.

UNDERGROUND CON EDISON MANHOLES.

C. BETWEEN SERVICE END BOXES ON ELEVATED STRUCTURE COLUMNS AND

B. IN CONDUITS BETWEEN ELEVATED AND SUBWAY STRUCTURES.

A. IN ALL UTILITY LINES ON ELEVATED STRUCTURES.

INSTALL INSULATING COUPLINGS AS FOLLOWS (SEE DETAIL C):13.

AREAS FROM PAINT, LACQUER ETC., IF NECESSARY.

ALL GROUNDING CONNECTIONS SHALL BE BARE METAL TO BARE METAL. CLEAN CONTACT12.

THAT WILL ENSURE AN EFFECTIVE GROUNDING CONNECTION.

ALL GROUNDING CONNECTIONS SHALL BE READILY ACCESSIBLE AND MADE IN A MANNER 11.

SIZE OF EACH EGCs SHALL BE BASED ON TABLE B.

RACEWAY, A DEDICATED EGC SHALL BE PROVIDED FOR EACH BRANCH CIRCUIT.

WHERE MULTIPLE BRANCH CIRCUIT CONDUCTORS ARE INSTALLED INTO A SINGLE

PROVIDE EGC FOR ALL FEEDER AND BRANCH CIRCUIT CONDUCTORS, SIZED PER TABLE B.10.

FULL SIZED EGC SHALL BE PROVIDED IN EACH CONDUIT.

B. WHERE CIRCUIT CONDUCTORS ARE INSTALLED IN PARALLEL IN MULTIPLE CONDUITS,

LARGER THAN CIRCUIT CONDUCTORS SUPPLYING THE EQUIPMENT.

TO CIRCULAR MIL AREA AS PER LATEST NEC SECTION 250.122B. EGC SHALL NOT BE

VOLTAGE DROP, EGC SIZES SHALL BE INCREASED PROPORTIONATELY ACCORDING

A. WHERE CIRCUIT CONDUCTORS ARE INCREASED IN SIZE TO COMPENSATE FOR 9.

CONDUCTORS.

INCLUDING SERVICE END BOX AND RUN IN THE SAME CONDUIT WITH CIRCUIT

FOR MC CABLES. EGC SHALL BE INSTALLED BETWEEN ALL ELECTRICAL EQUIPMENT

EGC SHALL BE COPPER WITH GREEN INSULATION AND SIZED AS PER TABLE B EXCEPT8.

THAN 1100 KCMIL COPPER, REFER TO LATEST NEC ARTICLE 250.28 FOR SIZES.

TABLE A. WHEN MULTIPLE SERVICE ENTRANCE PHASE CONDUCTORS ARE LARGER

THE SIZE OF THE BONDING JUMPER IN THE SERVICE SWITCH SHALL BE AS PER 7.

JOINTS AND SIZED AS PER TABLE A.

INSULATION AND INSTALLED IN ONE CONTINUOUS LENGTH WITHOUT SPLICES OR

THE GROUNDING ELECTRODE CONDUCTOR SHALL BE COPPER WITH GREEN 6.

THE ENCLOSURE AND CONNECT THE CONDUCTOR TO A GROUND BUS.

CONDUCTOR FROM ONE CONDUIT BUSHING TO ALL CONDUIT BUSHINGS ENTERING

INSTALLED WITHIN THE ENCLOSURE. RUN A CONTINUOUS COPPER BONDING

FITTINGS BOXES AND ENCLOSURES. THE SIZE SHALL BE AS PER TABLE B AND

BOND NON-CURRENT CARRYING METAL PARTS SUCH AS RACEWAYS, TROUGH, METER 5.

E. TUNNEL LIGHTING ROOMS, F. PUMP ROOMS.

B. ESCALATOR/ELEVATOR ROOMS, C. ELECTRIC PANEL ROOM, D. FAN PLANT ROOM,

IN ALL ELECTRICAL EQUIPMENT ROOMS SUCH AS: A. AIR COMPRESSOR ROOMS

ROOM, PROVIDE ONE STRUCTURAL STEEL CONNECTION FOR EQUIPMENT GROUNDING

FOR LOCATIONS WHERE THERE IS NO EGC COMING FROM THE ELECTRIC SERVICE 4.

CONDUCTORS ENTER AND SERVICE SWITCH IS LOCATED) FOR GROUNDING.

EACH ELECTRIC SERVICE ROOM WHERE UTILITY CO. SERVICE ENTRANCE

PROVIDE TWO STRUCTURAL STEEL CONNECTIONS, AT LEAST TEN FEET APART, IN 3.

PERMITTED.

UTILITY NEUTRAL SHALL NOT BE GROUNDED. GROUNDING TO TRACK RAIL IS NOT2.

ARE SHOWN.

FOR CLARITY, ONLY EQUIPMENT GROUNDING CONDUCTOR (EGC) AND NEUTRAL1.

NOTE 1

CONDUCTOR

ENTRANCE

SERVICE

ELECTRICAL EQUIPMENT

TYPICAL GROUNDING OF

DRAWN BY

DESIGNED BY

CHECKED BY

APPROVED BY

MANAGEMENT

CAPITAL PROGRAM

DEPARTMENT OF


ISSUE

DATE :

DRAWING NO.

R:\61465\grand_street\ele\standards\e-2024.dgn 07-JAN-2020 12:24 sandraPRINT AS OF

15AT

100AF

1P

15AT

100AF

1P

S. CALLENDER

S. SHAH, P.E.

G. REVES, P.E. (SIGNED)

(SIGNED)

(SIGNED)

(SIGNED)

MTA URBAN PANEL INSTALLATION

S. CALLENDER

NOTES

EQUIPMENT CIRCUIT WIRING DIAGRAM

LIGHTING PANEL

FROM

DO

WN

POST LIGHT

ENTRANCE

NOTE 13

DETAIL A

(NOT TO SCALE)

G

(NOT TO SCALE)

TYPICAL SUBWAY ENTRANCE WIRING DETAILS

GNPHGNPH

NOTE 6

CONNECTOR

GROUNDING

TO

NOTE 6

CONNECTOR

TO GROUNDING

FROM LIGHTING PANEL

POST LIGHT

TO ENTRANCE

LIGHTING FIXTURES

TO EMERGENCYPOST LIGHT

ENTRANCE

WIRING DETAILS

TYPICAL SUBWAY ENTRANCE

3#12 TYPE XHHW-2

NOTE 11

3 #12, TYPE XHHW-2

(TYP)

NOTE 7,10,12 & 17

LIGHT

ENTRANCE POST

(TYP)

NOTE 7,12 & 18

FIXTURE

EMERGENCY LIGHTING

NOTE 7,13 & 16

URBAN PANEL

NOTE 3

CONNECTOR

GROUNDING

LIGHT & URBAN PANEL IN THE K-RAILING

FOR EXISTING CONDITION ROUTE CABLES FOR POST

TYPE XHHW-2

#12

1#12, FOR URBAN PANEL

1#12, FOR POST LIGHT

OR XHHW-2

#12, TYPE THHN

EMEM

EM EM

TIMES

FIXTURE SHALL BE ON ALL

OR APPROVED EQUAL. LIGHT

SERIES BY LUMINAIRE LED

STAIR ENTRANCE. VPF 8

FIXTURE ON COPING AT

PROVIDE 4' VP, WP LED

(TTY)

NOTE 8

CONNECTOR

WIRE DETAIL A

POSTNOTE 16B

RAILING

TYP

NOTE 2,5

NOTE 9

URBAN PANEL

NOTE 11

XHHW-2

3#12,TYPE

OR XHHW-2

THHN

12#12,TYPE

LE

D

E-2024

URBAN PANEL, SEE NOTE 7 & 8

CIRCUIT GUARD (GFCI)

GLOBE LIGHT, SEE NOTE 7 & 8


POST

C

NOV 5, 2015

NOTE 7, 16D

208Y/120VAC LIGHTING PANEL

COVER-1

HAND HOLE

COVER-2

HAND HOLE

COVER-3

HAND HOLE

N

G

NOTE 16E

NOTE 16A & 16C

COPPER GROUND LUG

LED HANDRAIL

OR THHN

TYPE XHHW-2

12#12

15AT

100AF

1P

15AT

100AF

1P LED HANDRAIL


1#12, FOR LED HANDRAIL

LED HANDRAIL

LED HANDRAIL

1" CONDUIT CONCEALED IN CONCRETE (COPING)

FOR POST LIGHT, URBAN PANEL & LED LIGHTS IN

FOR NEW WORK ROUTE CABLES (XHHW-2)

FIXTURE.

THE LAMP FOR 2 HOURS MINIMUM "X" DENOTES THE COLOR OF THE

"DUAL LITE" CAT 3PG-X-HTR-PGMNT O.A.E. BATTERY SHALL OPERATE

18. EMERGENCY LIGHTING SHALL BE VANDAL RESISTANT, LED LIGHTS BY

EQUAL.

BY LIGHT EFFICIENT DESIGN CAT. # LED-8029E40A OR APPROVED

17. THE LAMP FOR THE ENTRANCE POST LIGHT SHALL BE 24 WATTS LED

URBAN PANEL.

E. CONNECT PHASE AND NEUTRAL CONDUCTORS TYPE XHHW-2 TO THE

URBAN PANEL INSTALLATION.

D. REFER TO NOTE 7 FOR GFCI GUARD REQUIREMENT FOR

HAND HOLE COVER-3 TO THE COPPER GROUND LUG.

C. CONNECT EQUIPMENT GROUNDING CONDUCTOR, TYPE XHHW-2 IN

THE CONDUIT ENTRY INTO THE URBAN PANEL.

B. PROVIDE A RAIN TIGHT HUB, O-Z/GEDNEY SERIES CHM-T, FOR

A. PROVIDE THE COPPER GROUND LUG INSIDE THE URBAN PANEL.

PERFORM THE FOLLOWING WORK WHEN INSTALLING THE URBAN PANEL:

CONDUCTED BY AN MTA CONTRACTOR. THE MTA CONTRACTOR SHALL

16. THE INSTALLATION OF THE URBAN PANEL IS SEPARATE WORK TO BE

LED HANDRAIL AND BATTERY PACK.

FROM LIGHTING PANEL. PROVIDE CIRCUIT GUARD (GFCI) FOR EACH

15. EACH LED HANDRAIL SHALL BE FED FROM A SEPARATE CIRCUIT

14. FOR LED HANDRAILS REFER TO SPECIFICATION 16HS.

TYPE XHHW-2 SHALL BE CAPPED IN HAND HOLE.

LIGHTING PANEL. PHASE, NEUTRAL AND GROUND CONDUCTORS

13. IF NO URBAN PANEL IS INSTALLED, OPEN CIRCUIT BREAKER IN

OF ENTRANCE POST LIGHTS AND EMERGENCY LIGHTING FIXTURES.

12. REFER TO CONTRACT DRAWINGS FOR QUANTITY AND EXACT LOCATION

600VAC.

11. CONDUCTORS IN POST AND RAILING SHALL BE UL LISTED TYPE XHHW-2

10. ALL THE ENTRANCE POST LIGHTS SHALL BE PHOTOCELL CONTROLLED.

O-Z/GEDNEY CAT #HBLG WITH STAINLESS STEEL SCREW.

9. USE A SPECIFICATION GRADE INSULATED GROUNDING BUSHING,

FROM CIRCUIT GUARD TO GLOBE AND URBAN PANEL.

CIRCUIT GUARD AS PER NOTE #7 AND RUN NEW CABLE AND CONDUITS

CIRCUIT CABLE IN THE MEZZANINE AREA NEXT TO STAIRS AND PROVIDE

8. FOR EXISTING PANEL WITHOUT GFCI BREAKERS, SPLICE THE EXISTING

HANDRAIL LIGHTS.

PROVIDE DEDICATED FEED FOR GLOBE LIGHT, URBAN PANEL AND LED

LIGHTING FIXTURES, URBAN PANEL AND LED HANDRAIL LIGHTS.

LIGHTING PANEL TO FEED THE ENTRANCE POST LIGHTS, EMERGENCY

HUBBELL CAT. # GFHW13105 OR APPROVED EQUAL OUTSIDE THE

7. PROVIDE 30A, 125V AC CIRCUIT GUARD (GFCI) WITH AUTO RESET

TYPE XHHW-2 TO GROUNDING CONNECTOR IN POST.

6. EXTEND AND TERMINATE GROUNDING CONDUCTOR FROM 3 #12

NECESSARY.

METAL. CLEAN THE CONTACT AREAS FROM PAINT, RUST, ETC., IF

5. ALL THE GROUNDING CONNECTIONS SHALL BE BARE METAL TO BARE

4. GROUNDING CONDUCTORS SHALL BE CONTINUOUS.

POST FOR MOUNTING BOLTS.

CONTAMINANTS FROM ENTERING THE CONTACT AREA. DRILL AND TAP

FACTORY INSTALLED OXIDE INHIBITORS TO PREVENT MOISTURE AND

SERIES WITH 8 PORTS. GROUNDING CONNECTORS SHALL HAVE

3. GROUNDING CONNECTOR SHALL BE BURNDY UNITAP TYPE BIBS-MT

COMPONENTS.

EFFECTIVELY GROUNDED BY BOLTING ALL THE RAILING AND POST

AND HANDRAILS SHALL BE ELECTRICALLY CONTINUOUS AND

2. ALL SUBWAY ENTRANCE RAILING, SECTIONS, POSTS, URBAN PANELS,

DETAILS.

1. REFER TO ARCHITECTURAL DRAWINGS FOR POST AND HANDRAIL

STANDARD DRAWING

AND HANDRAIL LIGHT WIRING DETAILS

EMERGENCY LIGHTING, URBAN PANEL

SUBWAY ENTRANCE POST LIGHT,

E-2041

NOV 24, 2003

DATE :

DRAWING NO.

07-JAN-2020 12:25 sandraPRINT AS OF

DRAWN BY

DESIGNED BY

CHECKED BY

APPROVED BY

MANAGEMENT

CAPITAL PROGRAM

DEPARTMENT OF

STANDARD DRAWING

T. SEN, P.E.

G. REVES, P.E.


ISSUE E

G. ANTONY

K GEORGIADIS

(SIGNED)

(SIGNED)

(SIGNED)

(SIGNED)

APPROX. 5'

COLUMN OR WALL BETWEEN ADJACENT TRACKS

DIRECTION OF TRAIN

NOTES

1.

2.

3.

4.

5.

6.

7.

8.

9.

BE DETERMINED AS RECOMMENDED BY MANUFACTURER.

BOLT SIZE FOR CONDUIT STRAP, BACK STRAP AND STUD ANCHORS SHALL

STRUCTURAL ENGINEERING PRIOR TO CHASING OF CONCRETE CEILING.

SUBMIT A COMPLETE INSTALLATION DETAIL FOR EACH TRACK CROSSING TO

R:\61465\grand_street\ele\standards\e-2041 rev e.dgn

REQUIRES ENGINEER'S APPROVAL.

NECESSARY, CUT AND CHASE CEILING. CUTTING AND CHASING CEILING

(LLLE). CHECK CLEARANCES PRIOR TO AND AFTER INSTALLATION. IF

EQUIPMENT SHALL NOT ENCROACH ON THE LIMITING LINE OF LINE EQUIPMENT

(TYP)

SPANNING TRACK

EXISTING BEAM

CEILING

CEILING

DETAIL A

DETAIL B

2" MINIMUM

NOTE 4

INCH BOLT21

FLAT WASHER

FLAT WASHER

LOCK WASHER

HEX NUT

SPANNING TRACK

EXISTING BEAM

EXISTING COLUMN

CLAMP

BAR

..........

..........

... ..

NOTE 9

BACK STRAP

STRAP AND

CONDUIT

WALL OR CEILING

WASHER AND HEX NUT

FLAT WASHER, LOCK

STAINLESS STEEL

DETAIL A (NTS)

STEEL STUD ANCHOR

RED HEAD STAINLESS

DETAIL B (NTS)

(DETAIL "B")

FEET CENTERS. ALTERNATE DIRECTION OF STRAPS AND BACK STRAPS.

MOUNT CONDUIT ON CEILING WITH STRAPS AND BACK STRAPS ON 2

DETAIL B

2 RECESSED FLAT CEILING (NTS)

3 FLAT CEILING WITHOUT BEAMS (NTS)

USE RIGID GALVANIZED STEEL CONDUIT TO CROSS THE TRACK.

TYPES OF MOUNTING DETAIL

TYPES OF CEILING

1 CURVED CEILING (NTS)

BARS (TYP)

TO FIT PROTECTION

CUT CONCRETE

NOTES 1 AND 2

STEEL PROTECTION BAR

AFTER INSTALLATION OF THE BAR.

BE CUT OUT FOR THE INSTALLATION OF THE BAR. RESTORE CONCRETE

FEET ON CENTER. THE CONCRETE ABOUT THE FLANGE OF THE BEAMS SHALL

THE ADJACENT CEILING BEAMS OF THE CEILING BAY, APPROXIMATELY 5

ENDS OF THE STEEL PROTECTION BARS SHALL REST ON THE FLANGES OF

BAR CLAMPS WITH SLOTTED HOLES.

ON FLANGES OF CEILING BEAMS, PROVIDE 2 INCH WIDE, GALVANIZED

INCH THICK, LENGTH AS REQUIRED. WHERE INSTALLED 21INCHES WIDE,

STEEL PROTECTION BARS SHALL BE HOT DIPPED GALVANIZED STEEL, 2

FEET CENTERS.

CONDUITS/CABLES CROSSING THE TRACK. BAR SPACING SHALL BE ON 5

INSTALL STEEL PROTECTION BARS MOUNTED BELOW OVERHEAD

PROTECTION BARS

(TYPICAL)

SEE NOTE 5

LOCK WASHER AND ONE HEX NUT PER BOLT. (DETAIL "A")

WASHERS, LOCK WASHERS AND HEX NUTS. USE TWO FLAT WASHERS, ONE

SECURE STEEL PROTECTION BARS WITH STAINLESS STEEL BOLTS, FLAT

NOTE 10

CONDUIT OR MC CABLE

10.WHEREVER MC CABLE IS USED THIS DRAWING SHALL BE APPLICABLE.

E-2052

NOV 24,2003

DATE :

DRAWING NO.


DRAWN BY

DESIGNED BY

CHECKED BY

APPROVED BY

MANAGEMENT

CAPITAL PROGRAM

DEPARTMENT OF

(SIGNED)

STANDARD DRAWING


(SIGNED)

(SIGNED)

(SIGNED)ISSUE

NOTES

PUMP ROOM

1" MINIMUM

1.

MID RIVER PUMPS

1.

2.

WIRE/CABLE

1.

2.

WIRE/CABLE

1.

2.

CONDUIT

1.

2.

1.

1.

2.

1.

LP3-15

LINE 4: EQUIPMENT DESIGNATION OF SOURCE OF POWER

LINE 3: INCOMING FEEDER AND CONDUIT SIZES

LINE 2: AMPERE, PHASE, WIRE, HP, WINDINGS, OR OTHER APPLICABLE INFORMATION

LINE 1: EQUIPMENT DESIGNATIONLINE 3: BRANCH CABLE AND CONDUIT SIZES

LINE 2: FRAME, POLES, AND TRIP RATING OF CIRCUIT BREAKER

LINE 1: DESIGNATION OF EQUIPMENT BEING SERVED

SERVICE SWITCH NORMAL, BPSN

AND WIRE TAGS

EQUIPMENT IDENTIFICATION

TYPICAL DETAILS FOR

1.

3.

DISTRIBUTION BOARD NORMAL-DBN

THE IDENTIFICATION SHALL BE:

A. CABLES IN MANHOLES AND CABLE CHAMBERS

4.

OR LETTERS EXCEEDS THE AVAILABLE LENGTH.

ABBREVIATIONS FOR THE INSCRIPTIONS IS PERMITTED ONLY WHEN NUMBER OF CHARACTERS

3.

4.

2.

PANELBOARD DESIGNATION, DASH LINE, AND CIRCUIT NUMBER.

APPURTENANCE SHALL BE PROVIDED WITH IDENFICATION PLATE TO SHOW ABBREVIATED

EACH LIGHTING FIXTURE, HEATER, RECEPTACLE, SWITCH, AND OTHER ELECTRICAL

H. NAMEPLATE FOR FEEDER BREAKER/SWITCH

G. ELECTRICAL DEVICE TAGGING

4#2-1•"C

100AF-100AT-3P

COMMUNICATION PANEL-CP

WHITE CORE.

THE NAMEPLATE COLOR SHALL BE AS SHOWN BELOW AND ENGRAVED THROUGH TO THE

WHITE CORE:

THE NAMEPLATE COLOR SHALL BE AS SHOWN BELOW AND ENGRAVED THROUGH TO THE

RED FOR 600V AC AND DC

ORANGE FOR 480Y/277VAC

BLACK FOR 208Y/120VAC

OR LETTERS EXCEEDS THE AVAILABLE LENGTH.

ABBREVIATIONS FOR THE INSCRIPTIONS IS PERMITTED ONLY WHEN NUMBER OF CHARACTERS

TOP OR ADJACENT TO THE BREAKER.

WITH NAMEPLATE AFFIXED WITH HIGH STRENGTH ADHESIVE. IT SHALL BE AFFIXED ON THE

EACH FEEDER BREAKER IN SWITCHBOARD AND DISTRIBUTION BOARD SHALL BE PROVIDED

2.

MARKED ONLY WHEN THERE ARE MULTIPLE NEUTRALS IN THE SAME PULL/JUNCTION BOX.

LETTERING SHALL BE BLACK ON YELLOW BACKGROUND. THE NEUTRAL WIRE SHALL BE

EACH CABLE SHALL BE IDENTIFIED WITH WRAPAROUND TYPE SNAP-ON CABLE MARKERS.

MARKED ONLY WHEN THERE ARE MULTIPLE NEUTRALS IN THE SAME ELECTRICAL ENCLOSURE.

LETTERING SHALL BE BLACK ON YELLOW BACKGROUND. THE NEUTRAL WIRE SHALL BE

EACH CABLE SHALL BE IDENTIFIED WITH WRAPAROUND TYPE SNAP-ON CABLE MARKERS.

LINE 1: POWER SOURCE-CIRCUIT NUMBER, AND PHASE


E. TAGGING FOR CONDUITS

F. SNAP ON MARKERS FOR CONDUITS

C. CABLES IN ELECTRICAL ENCLOSURE

D. NAMEPLATE FOR ELECTRICAL EQUIPMENT

208Y/120V

5.

LINE 1: DESTINATION, CIRCUIT NUMBER, AND PHASE


DBN-5, A

FAN, DBN-5, N

NO INSCRIPTION ON LINE 1 AND 3 FOR SPARE BREAKER.

2.

3.

IDENTIFIED/TAGGED AS DESCRIBED ON THIS DRAWING AND AS PER SPECIFICATIONS.

CABLE CHAMBERS, PULL BOXES, CONDUITS, AND ELECTRICAL ENCLOSURES SHALL BE

ALL ELECTRICAL EQUIPMENT, FEEDER BREAKER/SWITCH, CABLES/WIRES IN MANHOLES,

AREA SERVED BY EACH.

DISCONNECT LOCATION DENOTING OTHER SERVICE SUPPLYING THE FACILITY AND THE

PERMANENT NAMEPLATE, PER ITEM H, SHALL BE INSTALLED AT EACH SERVICE

WHEN THERE IS MORE THAN ONE ELECTRIC SERVICE SUPPLIED IN A FACILITY, A

TRANSFORMER NAMEPLATE COLOR SHALL BE SELECTED FOR THE HIGHEST VOLTAGE.

INSCRIPTION ON EACH LINE SHALL BE AS FOLLOWS:

AS INDICATED BELOW, WITH THREE LINES OF 0.25 INCH HIGH CAPITAL LETTERS. THE

0.062" THICK WITH EDGES BEVELED 0.032X 45 DEGREES. NAMEPLATES SHALL HAVE COLOR

THE NAMEPLATE SHALL BE ENGRAVED, LAMINATED THERMO-SETTING PLASTIC, 1" H X 4" W X

INSCRIPTION ON EACH LINE SHALL BE AS FOLLOWS:

COLOR AS SHOWN BELOW WITH FOUR LINES OF 0.25 INCH HIGH CAPITAL LETTERS. THE

W X 0.125" THICK WITH EDGES BEVELED 0.062 X 45 DEGREES. NAMEPLATE SHALL HAVE

THE NAMEPLATE SHALL BE ENGRAVED, LAMINATED THERMO-SETTING PLASTIC, 1.625" H X 6"

AFFIXED WITH HIGH STRENGTH ADHESIVE TO THE OUTER ENCLOSURE.

AUTOMATIC TRANSFER SWITCHES, FUSE BOXES, ETC SHALL BE PROVIDED WITH A NAMEPLATE

DISCONNECTS, SWITCHBOARDS, DISCONNECT SWITCHES, ENCLOSED BREAKERS, CABINETS,

ALL ELECTRICAL EQUIPMENT SUCH AS DISTRIBUTION BOARDS, PANELBOARDS, SERVICE

C. RED FOR 600V AND HIGHER VOLTAGE

B. ORANGE FOR 480Y/277VAC

A. BLACK FOR 208Y/120VAC

D

1.5"

0.125"0.125"

0.25"

0.25"

0.125"

0.125"

0.125"

0.125"DBN-12

0.125" MIN.

0.125" MIN.

0.25"

2"

1"

4"

6"

1.625"

0.75"

0.125"

0.125"

0.125"

0.125"

TR135-2, 4, 6

26, 28, 30

TL135S-

0.125"

SHALL BE PROVIDED WITH NAMEPLATE AS SHOWN IN ITEM D AND H.

ALL ELECTRICAL EQUIPMENT, EXISTING AND NEW, SHOWN ON THE ONE-LINE DIAGRAM

ACCEPTABLE MANUFACTURERS:

ENGINEER.

SUBMIT FOR APPROVAL BY THE ENGINEER. SUBMIT SAMPLES WHEN REQUESTED BY THE

PROVIDE SHOP DRAWINGS SHOWING IDENTIFICATION/INSCRIPTION IN EACH LINE AND

5.

4.

4.

3.

2.

1.

BE USED TO SECURE THE TAG.

SHALL BLACK, 0.125" HIGH AND ENGRAVED ON ONE SIDE. DOUBLED NO.18 MONEL WIRE SHALL

DURABLE, PLASTIC TAG AS MANUFACTURED BY SETON, STYLE NO. M4551. THE LETTERING

ALL PANELBOARDS, SWITCHES AND OTHER EQUIPMENT BY A 0.0625" THICK ROUND, YELLOW,

THE CONDUITS OF ALL FEEDERS AND BRANCH CIRCUITS SHALL BE PROPERLY DESIGNATED AT

5"

3.5"

B. CABLES IN PULL/JUNCTION BOXES

LINE 1: VOLTAGE, LINE 2: DESTINATION, LINE 3: ORIGIN (PANEL AND CIRCUIT NUMBER)

EMBOSSED, BLACK FILLED, 19 GAUGE BRASS AS MANUFACTURED BY SETON, STYLE NO. 37430.

TO THE CABLE WITH TWO LOOPS OF #18 MONEL WIRE. THE TAG SHALL BE STAMPED OR

EACH CABLE SHALL BE IDENTIFIED WITH A TAG AT THE END OF EACH DUCT AND FASTENED

TUNNEL. THE LETTERING AND ARROW SHALL BE BLACK ON AN ORANGE BACKGROUND.

BY SNAP-ON MARKERS. CONDUITS SHALL HAVE A MARKER PLACED EVERY 100 FT IN THE

ALL CONDUITS WITHIN ENCLOSURES AND RUNNING ALONG THE TUNNEL SHALL BE IDENTIFIED

THE ROOM OR EQUIPMENT NAME. (RECEPTACLES, TUNNEL LIGHTS, PUMP ROOM, ETC)

THE IDENTIFICATION SHALL BE AN ARROW POINTING IN THE DIRECTION OF THE LOAD AND

WITH AN IMPACT TYPEWRITER.

PERMANENT TYPE PRESSURE ADHESIVE. LETTERING SHALL BE BLACK 0.125" AND BE MADE

ALUMINUM. THE PLATES SHALL BE AFFIXED TO THE INTERIOR OF THE EQUIPMENT WITH A

IDENTIFICATION PLATES SHALL BE 0.75" X 0.25" MADE UP OF 0.003 INCH THICK ANODIZED

LO

AD

SO

UR

CE

A. SETON, B. ACTIONCRAFT, C. LEM PRODUCTS, INC

2 SETS 4#500KCMIL, 1/0G IN 2-4"C

800A,208Y/120V,3PH,4W,SN,GND

S.PIERI

I. ARC FLASH PROTECTION LABEL (SAMPLE)

CAL/SQ CM.

PROTECTION LABEL WHEN INCIDENT ENERGY IS GREATER THAN OR EQUAL TO 40

PROVIDE A RED "DANGER" (INSTEAD OF ORANGE "WARNING") ARC FLASH

VINYL AND LOCATED SO THAT IT IS CLEARLY VISIBLE TO QUALIFIED PERSONS.

THE LABELS SHALL BE 3.5" WIDE X 5" HIGH MADE OF DURABLE SELF ADHESIVE

APPROVED EQUAL AS ILLUSTRATED.

Z534.4 REQUIREMENTS AND SHALL BE GENERATED BY SKM SOFTWARE, OR

THE LABELS SHALL SATISFY THE LATEST ISSUE OF NFPA 70E, OSHA AND ANSI

LABELS FOR ELECTRICAL SAFETY IN THE WORKPLACE.

OTHER SWITCHING EQUIPMENT SHALL HAVE ELECTRIC ARC FLASH PROTECTION

CONTROL PANELS, METER SOCKET ENCLOSURES, MOTOR CONTROL CENTERS AND

ALL ELECTRICAL EQUIPMENT, SUCH AS SWITCHBOARDS, PANELBOARDS, INDUSTRIAL

E.DIAZ

S.SHAH,P.E.

G.REVES,P.E.

JUN 3, 2004

G. HAIMOVICI

FOR STATIONGENERATOR CONNECTION BOX

E-2058

(SEE NOTE 5B)

B C N G

A B C

DATE :

DRAWING NO.


DRAWN BY

DESIGNED BY

CHECKED BY

APPROVED BY

MANAGEMENT

CAPITAL PROGRAM

DEPARTMENT OF

B


STANDARD DRAWING

(SIGNED)

(SIGNED)

(SIGNED)

(SIGNED)

S. CALLENDER

S. SHAH, P.E.

G. REVES, P.E.ISSUE

SCB

GCB

30"

#12

24"

CAP

6"

NOTE 12

DISTRIBUTION BOARD

480Y/277VAC, 3P, 4W

208Y/120VAC, 3P, 4W OR

CON EDISON SERVICE

3P

NOTE 14

INTERLOCK

SWITCH

SERVICE

GENERATOR CONNECTION

BY OTHERS

GENERATOR

FROM

NOTE 10

PH

AS

E

A

PH

AS

E

B

PH

AS

E

C

NE

UT

RA

L

GR

OU

ND

WATERTIGHT HUB

BOARD

TO DISTRIBUTION

EQ

NIPPLE

BY OTHERS

FROM GENERATOR

3" WATERTIGHT HUB

INSULATED GROUNDING BUSHING

BLOCK NAMEPLATE

MOUNTING LUGS (4)

NOTE 15

EQ

NOTE 10

REFERENCES

E-2020

E-2052

AND ELEVATED LINES

TYPICAL GROUNDING OF ELECTRICAL EQUIPMENT SUBWAYS 1.

2.

A

2"

1.625"

1.625"

NOTES

WIRE TAGS

TYPICAL DETAILS FOR EQUIPMENT IDENTIFICATION AND

(NTS)

GENERATOR CONNECTION BOX (GCB)

(NTS)

COVER NAMEPLATES

(NTS)

BLOCK NAMEPLATE

"21

10

NOTE 9

4 #4/0, #2G IN 2"CNOTE 13

200AT

225AF

NOTE 16


4#4/0, #2G IN 2"C

200A, 208Y/120VAC, 3P, N, GND

GENERATOR CONNECTION BOX NORMAL-GCBN

CAT# ATM3 WITH ULTRA SAFE HOLDERS CAT# USM3.

16. PROVIDE THREE 3A, 600VAC, FAST ACTING FUSES, MERSEN

10% OF THE NORMAL VOLTAGE.

VOLTAGE INDICATORS. SET TRIP POINT INDICATION TO MINUS

OR MODEL #C2638 FOR 480VAC, WITH PHASE REVERSAL AND LOW

15. TIME MARK 3-PHASE MONITOR SHALL BE MODEL #B2638 FOR 208VAC

IF REQUIRED, SHALL BE COORDINATED WITH THE FIELD ENGINEER.

REMOVABLE IN OPEN POSITION ONLY. THE SERVICE SHUTDOWN,

ONE MAY BE CLOSED AT ANY ONE TIME. KEY SHALL BE

THE REVERSE FED 200 AMPERE CIRCUIT BREAKER SO THAT ONLY

14. PROVIDE A KEY TYPE INTERLOCK FOR THE SERVICE SWITCH AND

IN 2" CONDUIT TO MAIN BUS OF THE DISTRIBUTION BOARD.

CIRCUIT BREAKER SHALL BE CONNECTED WITH 4#4/0, #2 GROUND

INSTALLED IN A SEPARATE ENCLOSURE. THE LINE SIDE OF THE

DISTRIBUTION BOARD, THE CIRCUIT BREAKER SHALL BE

13. IF REVERSE FED CIRCUIT BREAKER CANNON BE PROVIDED IN

OTHER CIRCUIT BREAKERS IN THE DISTRIBUTION BOARD.

SWBDR IN RESERVE EDR) WITH RATINGS CORRESPONDING TO THE

DISTRIBUTION BOARD (DBN OR SWBDN IN NORMAL EDR AND DBR OR

12. PROVIDE A REVERSE FED 200 AMPERE CIRCUIT BREAKER IN THE

AND RESERVE ELECTRICAL DISTRIBUTION ROOMS.

11. PROVIDE A GCB AND ASSOCIATED WIRING IN BOTH THE NORMAL

BE BY OTHERS.

10. WIRING CONNECTION BETWEEN THE GCB AND THE GENERATOR SHALL

9. COLOR CODE WIRING BETWEEN CIRCUIT BREAKER AND GCB.

CONDUITS, AND SERVICE GROUND. SEE E-2020.

8. BOND DISTRIBUTION BLOCK LABELED "GROUND" TO THE ENCLOSURE,

THE TOP SHALL EXTEND TO THE CEILING.

PROVIDE A 12" CLEARANCE ON BOTH SIDES. THE CLEARANCE ON

THE BOX TOP SHALL BE 4 FOOT 6 INCHES ABOVE THE FLOOR LEVEL.

7. INSTALL THE GCB ON THE EDR WALL CLOSE TO THE SWITCHBOARD.

BOX.

6. THE GCB WIRING ENTRY AND EXIT SHALL BE ON THE TOP OF THE

AND AFFIXED WITH STAINLESS STEEL SCREWS AND ADHESIVE.

THROUGH TO THE WHITE CORE. THE EDGE SHALL BE NEATLY BEVELED

FOR 208Y/120VAC AND ORANGE FOR 480Y/277VAC ENGRAVED

WITH ‚" HIGH LETTERING ENGRAVED. NAMEPLATE SHALL BE BLACK

„" THICK OUTDOOR GRADE MULTICOLORED LAMICOID PLASTIC SHEETS

5. PROVIDE A COVER NAMEPLATE AND A BLOCK NAMEPLATE MADE FROM

EACH POLE

B. SQUARE D PART #9080LB51, CLEAR PLASTIC COVER FOR

A. SQUARE D PART #KH-20, END CLAMP5

EQUAL WITH THE FOLLOWING ACCESSORY:

THE LOAD SIDE, SQUARE D PART #9080LBC165212 OR APPROVED

ALLOY, WITH ONE OPENING PER POLE ON THE LINE SIDE AND

4. THE POWER DISTRIBUTION BLOCKS SHALL BE 1POLE, COPPER

(3P, N, G) FOR EITHER 480Y/277VAC OR 208Y/120VAC SYSTEMS.

3. THE GCB IS DESIGNED FOR 200 AMPERE, 600VAC, 5 POLE

OR APPROVED EQUAL. PROVIDE LOCK AND KEYS FOR THE BOX.

CATALOG #A-30H2408SS6LP WITH HOFFMAN PANEL PART #A-30P24

2. THE GCB SHALL BE NEMA 4X, STAINLESS STEEL, HOFFMAN

WITH CLEARANCE DIMENSIONS AS INDICATED.

WITH FIVE POWER DISTRIBUTION BLOCKS AND TWO NAMEPLATES

FACTORY ASSEMBLED AND PRE-WIRED EXCEPT FOR EXTERNAL WIRES,

1. GENERATOR CONNECTION BOX (GCB) SHALL BE COMPLETELY

(SEE NOTE 3 AND 5)


4#4/0, #2G IN 2"C

200A, 480Y/277VAC, 3P, N, GND

GENERATOR CONNECTION BOX NORMAL-GCBN

ENCLOSUREDISTRIBUTION BOARD

PANELBOARD AND

E-2060

NOV 24, 2003

DATE :

DRAWING NO.


DRAWN BY

DESIGNED BY

CHECKED BY

APPROVED BY

MANAGEMENT

CAPITAL PROGRAM

DEPARTMENT OF


STANDARD DRAWING

(SIGNED)

(SIGNED)

(SIGNED)

(SIGNED)

B. M. PATEL

B. M. PATEL

Y. TEOH, P.E.

G. REVES, P.E.ISSUE

1.

SPECIFIED ON CONTRACT DRAWINGS. THE GENERAL REQUIREMENTS ARE:

SHALL BE ENCLOSED IN A STEEL OR STAINLESS STEEL CABINET AS

THE PANELBOARD/DISTRIBUTION BOARD BUS AND CIRCUIT BREAKER ASSEMBLY

2.

3. THE ENCLOSURE SHALL HAVE CONTINUOUSLY WELDED SEAMS.

4.

WELDED TO DOOR AND ENCLOSURE.

HINGES SHALL HAVE STAINLESS STEEL PINS. THE HINGES SHALL BE

5.

SELF-ADHESIVE BLACK NEOPRENE SPONGE RUBBER GASKET.

EXTERIOR DOORS SHALL BE COMPLETELY GASKETED WITH A

6.

7.

8.

FRAME.

A HEAVY GAUGE LUCITE THAT IS BOLTED IN PLACE IN THE DIRECTORY

ELECTROGALVANIZING DOOR. DIRECTORY FRAME SHALL BE COVERED BY

DIRECTORY FRAME SHALL BE WELDED TO INTERIOR OF DOOR BEFORE

9.

10.

MINIMUM SURFACE FOR GASKETING SHALL BE PROVIDED.

INCH 21FLAT SEALING SURFACE FOR THE NEOPRENE GASKETING. A

PROVIDE A CONTINUOUS RAIN GUTTER AROUND OPENING TO ACT AS A

11. PROVIDE MECHANISM TO LOCK CIRCUIT BREAKERS IN OFF POSITION.

12.

AND LEFT TO RIGHT, AS VIEWED FROM THE FRONT.

BREAKERS SHALL BE A, B, C, FROM FRONT TO BACK, TOP TO BOTTOM

THE PHASE ARRANGEMENT ON THREE-PHASE BUSES AND CIRCUIT

13.

14.

A. NOTES - GENERAL

1.

B. NOTES FOR STEEL ENCLOSURE

2.

ELECTRO-GALVANIZED. SEE SPECIFICATIONS FOR DETAILS ON PAINTING.

PAINT SHALL BE APPLIED AFTER CABINET HAS BEEN

3.

4.

THE EXTERIOR METAL SHALL BE MINIMUM 10 GAUGE.

C. NOTES FOR STAINLESS STEEL ENCLOSURE1.

BRUSHED FINISH.

THE EXTERIOR METAL SHALL BE MINIMUM 12 GAUGE, TYPE 304 WITH #4

2.

3. THE ENCLOSURE SHALL NOT BE PAINTED.

(TYPICAL FOR 4)

" DIA. HOLE85

W

DIMEN.

THE DOOR

INSIDE OF

FRAME ON

DIRECTORY

NOTE 6

VAULT LOCK

3-POINT

SEMI-FLUSH

LOCKING BARS

3"

3"

"211

4 REQUIRED

INSTALLATION

FOR SURFACE

MOUNTING PLATE

(TYPICAL, 2 REQUIRED)

WITH SCREWS

WEEP HOLES

6" MIN

DIMEN.

H

STEEL PINS

WITH STAINLESS

PIANO HINGE

DIMEN.

D

"85

NOTE 6

VAULT LOCK

3-POINT

SEMI-FLUSH

LOCKING BARS

3"

3"

"211

DIMEN.

W

THE DOOR

INSIDE OF

FRAME ON

DIRECTORY

4 REQUIRED

INSTALLATION

FOR SURFACE

MOUNTING PLATE

(TYPICAL, 2 REQUIRED)

WITH SCREWS

WEEP HOLES

6" MIN

NOTE 5

GASKETING

NOTE 8

DIRECTORY

NUMBERING (TYPICAL)

CIRCUIT BREAKER

1

7

11

13

3P

3P 3P

3P

1P

2P1P

1P

1P

2P

1P

2

8

10

12

14

18

NOTE 5,10

GASKETING NOTE 14

NOTE 8

DIRECTORY

NOTE 10

RAIN GUTTER

SCREWS ARE IN PLACE THE ENCLOSURE SHALL HAVE A NEMA 12 RATING.

WHEN THE WEEP HOLE SCREWS ARE REMOVED. WHEN THE WEEP HOLE

SPECIFIED. THE NEMA 12 ENCLOSURE SHALL HAVE A NEMA 3R RATING

ENCLOSURE SHALL BE COMBINATION NEMA 12/NEMA 3R OR NEMA 4X, AS

IS MORE THAN 30 INCHES.

PROVIDE TWO GASKETED OVERLAPPING DOORS WHEN ENCLOSURE WIDTH

APPENDAGES (HINGES, DIRECTORY FRAMES AND MOUNTING STUDS).

ELECTROGALVANIZED AFTER FABRICATION AND WELDING IN PLACE OF

EXTERIOR PARTS, INCLUDING BOX AND DOOR, SHALL BE

COLLAR ASSEMBLY.

FOR FLUSH MOUNTING, PROVIDE A TEN GAUGE, FOUR PIECE REMOVABLE

PIECE REMOVABLE COLLAR ASSEMBLY.

FOR FLUSH MOUNTING, PROVIDE A 12 GAUGE, STAINLESS STEEL FOUR

ONE DOOR PANEL TWO DOOR PANEL

ONE DOOR PANELTWO DOOR PANEL

(NTS)FRONT VIEW

(NTS)SIDE VIEW

(NTS)FRONT VIEW

(NTS)SECTION A-A

(NTS)SECTION B-B

LC

B B

LC

A A

(TYPICAL FOR 4)

DIA. HOLE

STEEL PINS

WITH STAINLESS

PIANO HINGE

NOTE 10

RAIN GUTTER

REQUIRED.

THE TYPE AND NUMBER OF CIRCUIT BREAKERS AND THE GUTTER SPACE

DIMENSIONS H, W, AND D TO BE DETERMINED BY THE MANUFACTURER FOR

A CONVENIENT LOCATION.

PROVIDE GROUND BAR KITS, WELDED INSIDE ENCLOSURE ON THE BACK AT

NO PROTRUDING PARTS.

LOCK, EMKA #333 KEY. MECHANISM SHALL BE SEMI FLUSH MOUNTED WITH

AND LOCK MECHANISM. EMKA #1107-U159-02B WITH A 1109-U2 CYLINDER

EXTERIOR DOORS SHALL BE SECURED BY A COMBINATION 3 POINT LATCH

BE ENTIRELY DEAD-FRONT WITH DOOR OPEN.

INTERIOR TRIM SHALL BE SO CONSTRUCTED THAT THE ENCLOSURE SHALL

AND NATIONAL ELECTRICAL CODE REQUIREMENTS.

STANDARD "PB1-977, UL STANDARD 67" AND APPLICABLE NEW YORK CITY

THE SIZE OF THE WIRING GUTTERS SHALL BE IN ACCORDANCE WITH NEMA

HEAT TRACE

E-2065

A. KOZAK

DRAWN BY

DESIGNED BY

CHECKED BY

APPROVED BY

MANAGEMENT

CAPITAL PROGRAM

DEPARTMENT OF


STANDARD DRAWING

(SIGNED)

(SIGNED)

(SIGNED)

(SIGNED) ISSUE

1.

(ZONE).

THE HEAT TRACE SHOWN IS FOR ONE TYPICAL HEAT TRACE CIRCUIT

2.

APPLICABLE.

USE SEPARATE CONDUIT FOR POWER AND CONTROL CIRCUITS WHERE

3.

REGARDLESS OF THE MANUFACTURER'S UPPER LIMIT.

EACH ZONE SHALL COVER NO MORE THAN 250 LINEAR FEET OF PIPE

DRAWINGS.

BE HEAT TRACED ARE INDICATED ON THE HYDRAULIC/MECHANICAL

CONTRACT DRAWING. THE LENGTH AND THE LOCATION OF THE PIPES TO

THE LOCATION OF THE HEAT TRACE PANEL SHALL BE AS SHOWN ON THE

RATED 5 OR 8 WATTS PER FOOT.

BASED ON HEAT LOSS CALCULATIONS, HEAT TRACE CABLES SHALL BE

COMPLIANCE WITH NYCT, NYS, OR NEC REQUIREMENTS.

LOCATIONS CLASSIFIED HAZARDOUS, SHALL BE HEAT TRACED IN

REFERENCED TO TRACK STATIONINGS.

LOCATIONS AND ALL TERMINATIONS. ALL LOCATIONS SHALL BE

AND CONTROL ROUTING, THE HEAT TRACE ROUTING, ALL SPLICE BOX

ON THE INSIDE OF THE CONTROL PANEL DOOR, INDICATING THE POWER

THE CONTRACTOR SHALL INSTALL A PLASTIC COATED ONE LINE DIAGRAM,

NUTS SHALL NOT BE ACCEPTABLE.

POWER CONNECTORS SHALL BE THE COPPER TERMINAL BLOCK TYPE. WIRE

STAINLESS STEEL ENCLOSURE.

HEAT TRACE CONTROL PANEL SHALL BE HOUSED IN A 14 GAUGE NEMA 4X

4.

5.

6.

7.

8.

9.

10.

11.

12.

13.

14.

15.

16.

17.

AND TESTING PROCEDURES.

SEE SPECIFICATION SECTION 16WA FOR THE SEQUENCE OF OPERATION

HEAT TRACE CONTROL PANEL

POWER CONNECTION KIT

SPLICE CONNECTION KIT

T-CONNECTION KIT

HEAT TRACE CABLE

BULB & CAPILLARY THERMOSTAT

1

DESCRIPTIONITEM NUMBER

DATE :

DRAWING NO.


POWER ON

(WHITE)

8 6 7

NOTES

1

CONTROLLER

MICROPROCESSOR

(WHITE)

POWER ON

(RED)

SYSTEM FAULT

2 6

34 6

7

7

6 5

2

3

4

5

6

7

8

9

CONTACTOR

2P

20AT, GFCI

2P208VAC

OTHERWISE INDICATED.

THE HEAT TRACE SHALL BE MICROPROCESSOR CONTROLLED UNLESS

CASE OF CONFLICT, THE MORE STRINGENT REQUIREMENT SHALL APPLY.

SPECIFICATIONS AND AS DIRECTED BY THE EQUIPMENT MANUFACTURER. IN

HEAT TRACE INSTALLATION SHALL BE TESTED IN ACCORDANCE WITH

NOTE 12

END OF THE HEATING CABLE USING A POWER CONNECTION KIT.

SURFACE USING GLASS TAPE. POWER IS CONNECTED TO ONE

THE JOB SITE AND INSTALLED ON TO THE PIPING OR TANK

THE SELF-REGULATING HEATING CABLE IS CUT TO LENGTH AT

TEMPERATURE SENSOR.

AUTOMATICALLY BY SENSING THE PIPE TEMPERATURE WITH THE

HEAT TRACE CABLES. THE HEATING CABLE SHALL BE CONTROLLED

TEE CONNECTION KITS ARE USED AS NECESSARY TO CONNECT

END SEAL KIT OR IS TERMINATED BY AN RT DEVICE. SPLICE AND

THE OTHER END OF THE HEATING CABLE IS SEALED USING AN

EQUIPMENT SCHEDULE

TEMPERATURE SENSOR (SEE NOTE 4)

END SEAL KIT

INSTALLATION DIRECTION.

NATIONAL ELECTRICAL CODE AND AS PER THE MANUFACTURERS

SHIELD SHALL BE EFFECTIVELY GROUNDED IN ACCORDANCE WITH THE

ALL EQUIPMENT SHALL BE EFFECTIVELY GROUNDED. HEAT TRACE CABLE

HEAT TRACE SYSTEM OVERVIEW

(NTS)

SUPERVISED HEAT TRACE (ONE ZONE)

(NTS)


(NTS)


FRONT VIEW

SAME MANUFACTURER.

INCLUDING THE POWER CONNECTOR KIT, SHALL BE SUPPLIED BY THE

ALL HEAT TRACE CABLE, SENSORS, END SEALS, AND CONNECTORS

AND CONCURRED BY THE EQUIPMENT MAINTAINER.

RUN IN AN EASILY ACCESSIBLE LOCATION, AS DIRECTED BY THE ENGINEER

INSTALL TEMPERATURE SENSORS IN THE COLDEST SECTION OF THE PIPE

FARENHEIT.

SET AT 40 DEGREES FARENHEIT, WITH ALARM AT 36 DEGREES

THE CONTROLLER FOR EACH MONITORED HEAT TRACE CABLE SHALL BE

T

(NTS)

NON-SUPERVISED HEAT TRACE (ONE ZONE)

REMOTE ALARM

FOR FUTURE

9

3P

ZONE 1

ZONE 2

CB1

CB2

2P

20AT

20AT

20AT

2P

2P

ZONE 8

CB8

FROM SEPARATE PANEL.

PROVIDE POWER FOR HEAT TRACE FROM A 3 POLE CIRCUIT BREAKER 18.

19.

20.

BY HEAT TRACE MANUFACTURER AS A COMPLETE PACKAGE.

ALL COMPONENTS IN HEAT TRACE CONTROL PANEL TO BE SUPPLIED

A. KOZAK

J. LEE, P.E.

J. ESPOSITO, P.E.

SEE NOTE 18

BY DESIGNER

AS REQUIRED

TRIP RATING

SEE NOTE 19

MAIN CB

E

FOR 8 ZONES.

BREAKER FOR 4 ZONES OR A 3 POLE 100A MAIN CIRCUIT BREAKER

HEAT TRACE CONTROL PANEL TO USE A 3 POLE 50A MAIN CIRCUIT

BREAKER.THE ENCLOSURE SHALL BE 14 GAUGE NEMA 4X.

POWER TO THIS CIRCUIT SHALL BE FROM A 2P-20AT GFCI CIRCUIT

ADJUSTABLE BULB AND CAPILLARY THERMOSTAT, SHALL BE USED. THE

HEAT TRACE ZONE, LIMITED IN LENGTH TO 250FEET, WITH A SINGLE POINT,

WHERE INDICATED IN THE CONTRACT, A SINGLE ZONE, NON-SUPERVISED

ELECTRICAL CIRCUIT BREAKER

JUNE 10, 2004

+

PRINT AS OF

E-2071

E. DIAZ

E

FOR 208 VAC SERVICESDC RELAY PANEL

NOV 24, 2003DATE :

DRAWING NO.


DRAWN BY

DESIGNED BY

CHECKED BY

APPROVED BY

MANAGEMENT

CAPITAL PROGRAM

DEPARTMENT OF


STANDARD DRAWING

(SIGNED)

(SIGNED)

(SIGNED)

(SIGNED)

S. CALLENDER

S. SHAH, P.E.

G. REVES, P.E.ISSUE

NOTES

2L1

1L1

211

212

MR2

1L2

1L3

6

5

7

11

MR1

C1

R1

11

12

20R1 R1

2L2

2L3

2N

5

6

7

11

1

3

SS

1

3

T 0

15

16

DC1

DC2

DC2

DC3

C15

6

7

11

1

317

16

MR3

3L1

3L2

3L3

3N

5

6

7

11

4L1

4L2

4L3

4N

MR4

1

318

17

5L1

5L2

5L3

5N

5

6

7

11

MR5

1

319

18

6L1

6L2

6L3

6N

5

6

7

11

MR6

1

320

19

GND DCRP

DCLP

"C.212#6 TR-1

2#1/0 TR-2"C. TRACK

E.D.R.

POSITIVE RAIL (THIRD RAIL)

NEGATIVE RAIL600 V DC

FUSE BOX.

METHOD OF INSTALLING

STANDARD DWG TITLED

1/0 TR CABLE. REFER TO

CONTACTOR

C1

RELAY

R1

TE

RMIN

AL

BL

OC

KS

O

SS T

ME

TE

RIN

G

RE

LA

YS,

TY

P.

MR1

MR2

MR3

MR4

MR5

MR6

PANEL DESIGNATION: DCLP

LOCATION:

SYSTEM VOLTAGE : 600VDC, 2W.,

MAIN LUGS ONLY

100

DESCRIPTION

LOAD

DESCRIPTION

LOAD

150AF-15AT-4P

150AF-15AT-4P

150AF-15AT-4P

150AF-15AT-4P

150AF-15AT-4P

150AF-15AT-4P

150AF-15AT-4P

150AF-15AT-4P

150AF-15AT-4P

150AF-15AT-4P

-ve

GND

TOTAL WATTS= AMPS= AIC=42000 @ 750VDC

REFERENCES

METHOD OF INSTALLING FUSE BOX

RAIL CONNECTORS

P-414-607

P-414-1576

P-434-2874

P-434-2875

JUNCTION BOX/"T" CONDULET1N

DC RELAY PANEL

DC LIGHTING PANEL

DC RELAY PANEL

BRANCH CIRCUIT

MAINS: AMP., TOP, BOTTOM,TYPE : FLUSH SURFACE

FUSE BOX FOR CONTACT RAIL TAP 31-60 AMPERES-DETAILS

FUSE BOX FOR CONTACT RAIL TAP 0-30 AMPERES-DETAILS

TO THIRD RAIL

VERTICAL PROTECTION BOARD FOR EQUIPMENT ADJACENT

1.

2.

3.

4.

5.

-

+

+

-

-

V

1

3

9

2

4

6

8

10

5

7

+

WATTS WATTS

VV

VV

VV

VV

VV

DC

INTERIOR LAYOUT

NOTE 3

150AF-40AT, 4P

ECB

NOTE 6

60A,1P

TFB

NOTE 5

TYP

NOTE 11

NOTE 15

TYP

NOTE 7

NOTE 4

NOTE 12

NOTE 8

NOTE 9

LIGHTING PANEL

" C TOƒ4#12,

UNLESS OTHERWISE INDICATED.

ALL BRANCH CIRCUIT WIRING FOR DC LIGHTING FIXTURES SHALL BE TYPE "KK" 18.

SHOWN ON THE DRAWINGS.

COVER WITH OPENINGS TO READ PROJECT NUMBER AND CONTRACT TITLE AS

IN A BOOKLET. THE BOOKLET SHALL BE PROVIDED WITH HEAVY DUTY PLASTIC

DRAWING, SCHEMATICS AND CATALOG CUTS FOR THE SYSTEM COMPONENTS

CONTRACTOR SHALL SUBMIT DETAILED SHOP DRAWING CONSISTING OF 17.

SHALL BE FULL DESCRIPTION OF EQUIPMENT.

THE FIRST LINE SHALL BE ABBREVIATED DESIGNATION AND THE SECOND LINE

FASTENED WITH 2 STAINLESS STEEL MACHINE SCREWS. THE INSCRIPTION ON

LAMINATED THERMO SETTING PLASTIC NAMEPLATE WITH 1/4" HIGH LETTERS

EACH DEVICE IN THE PANEL SHALL BE IDENTIFIED WITH 2"x3/4" x1/8" THICK 16.

RESPECTIVELY.

THE JUMPER WIRE SHALL BE #6 OR #2 FOR 60A OR 100A TRACK FUSE BOX 15.

EXCEPT INCOMING CABLES TO 'MR' RELAY L AND N TERMINALS.

ALL CABLES SHALL BE 'TR' RATED 1000V BY AIW CO. OR APPROVED EQUAL. 14.

PANEL WITH 4#12 IN 3/4" C. RESPECTIVELY.

INTERLOCKED WITH 211, 212, 11 & 12 OF SECOND RELAY AND CONTACTOR

TERMINAL 11, 12, 211 & 212 OF RELAY AND CONTACTOR PANEL ARE TO BE 13.

ON SECOND PANEL.

JUMPER MUST BE INSTALLED, UNLESS PANEL IS INTERLOCKED WITH R1 12.

IS INSTALLED, RELAY MAY BE REMOVED FROM SOCKET.

JUMPER MUST BE INSTALLED FOR UNUSED METERING RELAYS. ONCE JUMPER 11.

AND AS PER SPECIFICATION 16H AND 16HS.

INSTALL DC LIGHTING FIXTURES AS INDICATED IN THE CONTRACT DRAWINGS 10.

SWITCH AND CBK-CB10 FOR CONTACT.

MANUFACTURED BY ASEA BROWN BOVERIE SERIAL NO. CBF-S2MK FOR

SELECTOR SWITCH SS SHALL BE TWO POSITION (ON & TEST) AS 9.

CLASS 9050, TYPE JCK18V20/8501 NH7 SET AT 5 MIN.

RELAY R1 SHALL BE 120V, AC, DPDT POLE CONTROL RELAY BY SQUARE 'D' 8.

GAVAZZI CAT. NO. PPB-01-C-M23 OR APPROVED EQUAL.

METERING RELAYS MR1 THRU MR6 SHALL BE 3 PHASE, 4 WIRE BY CARLO 7.

CONTRACT DRAWINGS.

INSTALL 60A, OR SIZED AS INDICATED TRACK FUSE BOX ON TRACK AS PER 6.

SERIES CONNECTED WITH LONG LEG #6 WIRED.

HFDDC RATED 42000 AIC AT 750VDC. THE POLES OF THE BREAKERS ARE

DC LIGHTING PANEL SHALL HAVE CUTLER-HAMMER CIRCUIT BREAKER TYPE 5.

APPROVED EQUAL.

FOR 24VDC, WITH SINGLE PHASE POWER SUPPLY (100V - 240VAC) OR

CONTACTOR RATED AT 750VAC, 90AMP. NORMALLY CLOSED, COIL RATED

CONTACTOR C1 SHALL BE MFG. BY GIGVAC, TYPE GXNC14 WITH MAIN 4.

LONG LEG #2 WIRED.

ENCLOSURE. THE POLES OF THE BREAKERS ARE SERIES CONNECTED WITH

CIRCUIT BREAKER SHALL BE CUTLER-HAMMER TYPE HFDDC IN A NEMA 12 3.

INSTALLED IN A NEMA 12 PANELBOARD CONSTRUCTION ENCLOSURE.

DC RELAY PANEL AND DC LIGHTING PANEL SYSTEM COMPONENTS SHALL BE 2.

AS INDICATED AND WIRED OUT TO TERMINAL BLOCKS.

EXTERNAL WIRING. ALL TERMINALS INCLUDING SPARES SHALL BE MARKED

ASSEMBLED AND PRE-WIRED, EXCEPT FOR JUMPERS, INTERLOCKING AND

THE DC LIGHTING AND DC RELAY PANELS SHALL BE COMPLETELY FACTORY 1.

LIGHTING PANEL

" C TOƒ4#12,

LIGHTING PANEL

" C TOƒ4#12,

LIGHTING PANEL

" C TOƒ4#12,

LIGHTING PANEL

" C TOƒ4#12,

LIGHTING PANEL

" C TOƒ4#12,

P-414-609

LOCK AND FLAT

APPROX. 1" TO SUIT

1/2" SCREWANCHOR

DRILL AND TAP

6"L. X 2"W. X 5/8"D.

CEILING

GALVANIZED STEEL PLATE

FOR PENDANT MOUNTING

BATTER OF BEAM

BEND ANGLE SUPPORT TO

CONFORM WITH BATTER ANGLE

1/2" SCREW ANCHOR,

ACKERMAN-JOHNSON,

STAR, OR EQUAL

CEILING BEAM WITH

CONCRETE COVER

7" X 3" X 3/8"ALUM. ANGLE 2" LONG

SET SCREWBEAM CLAMP ASSEMBLY

UNISTRUT CORP. CAT. NO.

U-77 OR U-81 OR EQUAL

INSTALL GROUND

BUSHING TYPE

"GB" OZ. OR EQUALON CONDUIT

1/8" LEAD WASHER

INSTALL NO.10

GROUND WIRE

CONNECT TOFIXTURE TROUGH

2"

4"

1"

18" 6"

OR "M6" FOR CEILING MOUNTING

FIXTURE MOUNTING DETAILS

E-2074

DATE :

DRAWING NO.


DRAWN BY

DESIGNED BY

CHECKED BY

APPROVED BY

MANAGEMENT

CAPITAL PROGRAM

DEPARTMENT OF


STANDARD DRAWING

(SIGNED)

(SIGNED)

(SIGNED)

(SIGNED)ISSUE

MOUNTING DETAIL "M1"


TROUGH CLAMP TYPE "A"

DETAIL


TROUGH CLAMP TYPE "B"

DETAIL


MOUNTING DETAIL "M9A"

TROUGH CLAMP TYPE "B"

SECTION A-A

MOUNTING DETAIL "MC1"

MOUNTING DETAIL "ML2"



ALUM. PLATE

DETAIL

ALUM. CHANNEL

DETAIL

MOUNTING DETAIL "ML1A"




ALUM. STRAP

DETAIL

SECTION E-E



SECTION B-B

SECTION F-F




SECTION C-C

SECTION D-D

NOTES

FOR 1/2" ROD

TROUGH CLAMP

1/2" FULL

THREADED ROD

FLAT WASHER

WASHER

1/4" CLEAR AFTER

ELECTROPLATING

3/16" (MIN)

3/16" X 1"

SLOTTED HOLE

1 1/2"

DRILL AND TAP

FOR SET SCREW

FLAT WASHER

LOCK WASHER

1/2" HEX. NUT

FLAT WASHER

1/2" HEX. NUT

FLAT WASHER

FLAT WASHER

LOCK WASHER

9" X 9" STEEL BRACKET

2" WIDE, 3/8" THICK

1/2" ROD

LOCK WASHER

1/2" HEX. NUT

3/8" SCREW ANCHOR

FOR CONTINUATION SEE TROUGH

CLAMP TYPE "A" DETAIL

ON CONCRETE

ON STEEL

3/8" THICK

ELONGATE HOLES

VERTICALLY

3/8" STEEL PLATE, OMIT WHEN

BASE PLATE IS MOUNTED ON

COLUMN FLANGE OR CONCRETE

ALUM. BASEPLATE 3/8" TH.

3" X 1 1/2" ALUM. BAR

(WELD ALL AROUND)

SEE ALUM. CHANNEL DETAIL

SEE TROUGH CLAMP

TYPE "B" DETAIL

1 1/2"W. X 3"H. X 1/4"TH.

ALUM. TUBING

FOR CONTINUATION

SEE MOUNTING

DETAIL "M5"

THREADED ROD

STAINLESS STEEL

1/4-20 X 3/8" HEX.

HEAD SCREW, ROUND NOSE9/16" X 1" SLOTTED HOLE

3/16" (MIN)

FLAT WASHER

HO

LL

OW

TIL

E

CEILIN

G

VA

RIA

BL

E

1/2" COND. SPACER

FOR CONTINUATION SEE

MOUNTING DETAILS "M1"

VARIABLE

3" X 1 1/4" SOLID

ALUM. BAR

SHIM WHERE REQUIRED

(FOR LATERAL SUPPORT)

SHIM

3"

SEE TROUGH CLAMPTYPE "B" DETAIL

EXISTING BEAM

1 1/2"W. X 3"H. X 1/4"TH. ALUM.

TUBING TO SPAN CEILING BEAMS

SUITABLE ALUM.

ANGLE CLIP 2" LONG

1/2" DARDELET RIVET

BOLT ON NEUTRAL AXIS

WALL

1/2" ROD


TROUGH CLAMP TYPE "A" DETAIL

FLAT WASHER1/2" HEX. NUT

6" X 3" X 2" BENT

ANGLE SUPPORT

FLAT WASHER LOCK WASHER

FLAT WASHER

LOCK WASHER

3"

3/8"

FLAT WASHER

LOCK WASHER

1/2" HEX. BOLT

CEILING

TROUGH CLAMP

TYPE "A"

EXIS

TIN

G

CO

LU

MN

DRILL COLUMN

FOR LATERAL SUPPORT

INSTALL APPROX.

15'-0" SPACING

VARIABLE

3" X 1 1/4" SOLID

ALUM. BAR

1 1/4"

1/2" SCREW ANCHORSEE TROUGH CLAMP

TYPE "B" DETAIL

1 1/2"W. X 3"H. X 1/4"TH.

ALUM. TUBING TO

SPAN CEILING BEAMS

THREADED ROD



EXISTING STEEL BEAM

3/8" APPROVED

BEAM CLAMP

EXISTING STEEL BEAM

3/8" APPROVED

BEAM CLAMP



SEE TROUGH CLAMP

TYPE "B" DETAIL

ELONGATE HOLES INLENGTH OF CHANNEL ONLY

ALUM. STRAP, SEE DETAIL

ALUM. CHANNEL, SEE DETAIL

1 1/2"W. X 3"H. X 1/4"TH.

ALUM. TUBING

EXIS

TIN

G

CO

LU

MN

3" X 1 1/4" SOLIDALUM. BAR

DRILL COLUMN

INSTALL APPROX.

15'-0" SPACING

7/16" HOLE FOR3/8" BOLT

2'-0" MAX.

3/8" STEEL PLATE, OMIT WHEN

BASE PLATE IS MOUNTED ON

COLUMN FLANGE OR CONCRETE

(WELD ALL AROUND)

ALUM. BASE

PLATE 3/8" TH.

ELONGATE HOLES

HORIZONTALLY IN

BAR ONLY

SEE TROUGH CLAMP

TYPE "B" DETAIL1 1/2"W. X 3"H. X 1/4"TH.

ALUMINIUM TUBING

3"

1/8"

ANGLE DIRECTION OF RUN

ELONGATE HOLES IN3" X 4" X 1/4" ALUM

ANGLE 1 1/2" LONG

3" X 1 1/4" SOLIDALUM. BAR

ALUM. END PLUG

WELD ALL AROUND

ALUM. PLATE, SEE DETAIL

4" X 2 1/2" ELLIPSE

EXIS

TIN

G

CO

LU

MN

12"

MA

X.

2 3/8" O.D. SECTION

2'-1" TO 6'-0"

MAST ARM FORMED FROM 3 1/2" O.D. X 120 WALL

PFAFF AND KENDALL OR EQUAL.

TUBING 6063-T6 ALLOY. DWG NO. B-15483

INSTALL APPROX. 15'-0" SPACING

SLOPING CEILING

SHIM STEEL

FIXTURE TROUGH 1/8" LEAD WASHER

3/8" SCREW ANCHOR

EXISTING STEEL BEAM

1/2" HEX. BOLT

FLAT WASHER

LOCK WASHER

FLAT WASHER

LOCK WASHER

FLAT WASHER1/2" HEX. NUT

1/2" ROD



WHERE TROUGH IS INSTALLED

HANDHOLE AND INSTALL 1/8"

LEAD GASKET

UNDER OUTLET BOX, CUT 4"X4"

1/4"

1 3/16"2"

ALUM. TUBING

1 1/2"W. X 3"H. X 1/4"TH.

3/8" SCREW ANCHOR

1/2" SCREW ANCHOR,

ACKERMAN-JOHNSON,

STAR, OR EQUAL

TROUGH CLAMP

TYPE "A"

FIXTURE TROUGH

THREADED ROD

7"

4 1/2"

3/4"

3/4"

7"

5 1/2'

3/4"1 5/8"

1/4"

1 1/4" CL

7 7/8"

1 1/4"

1 1/4"

2 2/8"

1 1/2"

1 1/2"

14"

5 3/8"

2 13/16"

2 13/16"

1 1/2"

1 1/2"

AA

E

E

F

F

D

D

C

C

B

B

E

E

1 1/4"

6"

6"

3/4"

3/4"

6"

6"3/4"

3/4"

3/4"

3/4"

1"

3"

3"

1"

1"

1"

3"

1 1/2"

3/4" 5/8"

1"

FOR CONTINUATION SEE TROUGH

CLAMP TYPE "A" DETAIL

3/8" HEX. BOLT

3"

1/8"

3" X 1 1/4" ALUM. BAR

3/8" SCREW ANCHOR

TO BE INSTALLED AT 45' INTERVALS WHEN ROD LENGTH IS

18" TO 30" AND AT 30' INTERVALS WHEN ROD LENGTH IS MORE THAN 30".

CEILING

3/8"

3" WIDE STEEL STRAP ON

SIDE AWAY FROM

PLATFORM EDGE

1/2" HEX. NUT

FLAT WASHER


1/2" ROD

(FOR LATERAL SUPPORT)

TO BE INSTALLED AT 45' INTERVALS WHEN ROD LENGTH IS

18" TO 30" AND AT 30' INTERVALS WHEN ROD LENGTH IS MORE THAN 30".

VA

RIA

BL

E

3"

FLAT WASHER LOCK WASHER

ANCHOR

•" SCREW

TYPE "B"

1/2" HEX. NUT

FIELD CONDITION

1/2" HEX. NUT

STAINLESS STEEL

1/4-20 X 3/8" HEX.

HEAD SCREW,

ROUND NOSE

TROUGH CLAMP

TYPE "A"

1/2" ROD

(SEE NOTE3)

1/2" HEX. NYLON NUT

1/2" BOLT, NYLON NUT, FLAT

& LOCK WASHER (SEE NOTE 3)

(SEE NOTE 3)

1/2" HEX. NYLON NUT

(SEE NOTE 3)

1/2" HEX. NYLON NUT

(SEE NOTE3)

1/2" HEX. NYLON NUT

(SEE NOTE3)

1/2" HEX. NYLON NUT

(SEE NOTE 3)

(SEE NOTE 3)

(SEE NOTE3)

1/2" HEX. NYLON NUT

(SEE NOTE 3)

1/2" HEX. NYLON NUT

A

(SEE NOTE 3)

(SEE NOTE 3)

FLEXIBLE CONDUITS SHALL BE LIQUIDTIGHT, HOT DIP/MECHANICALLY GALVANIZED. EXTERNAL BONDING WIRE SHALL BE PROVIDED.

LIQUIDTIGHT FLEXIBLE CONDUITS SHALL BE USED WHERE REQUIRED, WITH THE MINIMUM LENGTH NECESSARY. FITTINGS FOR 12.

FOR PENDANT MOUNTING, REFER TO NOTES ON STANDARD DRAWING E-2067.11.

SCREWS, NUTS AND BOLTS SHALL BE STAINLESS STEEL.10.

AT 15 FOOT INTERVALS MAY BE SUBSTITUTED.

IN LIEU OF ALUMINUM TUBING, TROUGHING WITH AN ADEQUATE SELF-SUPPORTING DISTRIBUTED SECTION AREA SUPPORTED9.

ALL ALUMINUM SHALL BE ALLOY 6061-T6, UNLESS OTHERWISE INDICATED.8.

ALL STEEL PARTS FOR MOUNTING OF FIXTURES, EXCEPT 1 /2 " RODS, SHALL BE HOT-DIP GALVANIZED AFTER FABRICATION.7.

CONSIST OF SCREW ANCHOR, HEX. BOLT, FLAT WASHER AND LOCK WASHER.

ALL SCREW ANCHORS SHALL BE STAR TAMPIN, ANKERMAN-JOHNSON, OR EQUAL. ASSEMBLY SHALL6.

ALL FLAT AND LOCK WASHERS SHALL HAVE A CLOSELY ADHERING COATING OF AT LEAST .0006 INCH THICK CADMIUM PLATING.5.

ALL SCREWS AND BOLTS SHALL BE PROVIDED WITH HEAVY DUTY FLAT AND LOCK WASHERS.4.

PAINTED WITH A MIN. COATING OF Z.R.C. COLD GALVANIZING COMPOUND. ZRC CHEMICAL PRODUCT CO. OR APPROVED EQUAL.

LOCK WASHERS, UNLESS OTHERWISE INDICATED ROD SHALL BE ZINC ELECTRO PLATED AND SPRAYED OR

ALL THREADED ROD AND ALL BOLTS SHALL BE 1#2" WITH HEX. NUT, ELASTIC STOP NYLON NUT, FLAT AND 3.

ALL HOLES SHALL BE DRILLED FOR 1#2" BOLTS, UNLESS OTHERWISE INDICATED.2.

STEEL SHALL BE DRILLED AND TAPPED, WHERE REQUIRED PRIOR TO INSTALLATION.1.

B.M.PATEL

B.M.PATEL

Y.TEOH,P.E.

G.REVES,P.E.

NOV 24,2003

NOV 22, 2006

DATE :

DRAWING NO.


DRAWN BY

DESIGNED BY

CHECKED BY

APPROVED BY

MANAGEMENT

CAPITAL PROGRAM

DEPARTMENT OF

STANDARD DRAWING

(SIGNED)


ISSUE

E-2076

STATION LIGHTING FIXTURE

TROUGH MOUNTED

SPLICING DETAILS FOR

NOTES

1.

2.

3.

4.

DC

N

R

5CA

B

C

N

G

BALLAST

NOTE 5

COMPARTMENT

BALLAST

" CONDUIT43

5.

N

R

N

R A

B

C

N

G

COMPARTMENT

BALLAST

ACCESS COVER

N

5C

DC

R

SIDE

PLATFORM



EMERGENCY LIGHTING

COMMON

COMMMUNCATIONS

WIRE BOX

FIXTURE

SUPPLEMENTAL LIGHTINGFIXTURE

SUPPLEMENTAL LIGHTING

COMM

N

5C

DC

R

COMM

WIRE BOX

SIDE.

ORIENT "N" AND "R" COMPARTMENTS AND WIRE BOX TO BE ON PLATFORM

TROUGH DESIGNATIONS SHALL BE AS INDICATED IN THE CROSS SECTIONS,

THROUGH THE 5C COMPARTMENT OF THE TROUGH.

BALLAST LEADS SHALL BE CONNECTED TO THE BRANCH CIRCUIT WIRES

7.

6.

NORMAL LIGHTING

RESERVE LIGHTING

SIDE

PLATFORM

8.

NOTE 8

SPECIFICATIONS.

THE TROUGH SHALL HAVE FIVE COMPARTMENTS AS DETAILED IN THE

NOTE 6

BRANCH CIRCUITING

LOOP FOR CONTINUOUS

S. CALLENDER

S. CALLENDER

S. SHAH, P.E.

G. REVES, P.E.

(SIGNED)

(SIGNED)

(SIGNED)

BALLAST

BALLAST



COMM

WIRING DIAGRAM B

TROUGH COMPARTMENT LEGEND

WIRING DIAGRAM-B

WIRING DIAGRAM-A

(NTS)

TROUGH & FIXTURE CROSS SECTION

(NTS)

TROUGH & FIXTURE CROSS SECTION WITH SUPPLEMENTAL FIXTURE

SCOTCHLOK 562 SELF-STRIPPING ELECTRICAL TAP CONNECTORS.

CONNECT NORMAL, RESERVE, AND DC CIRCUIT WIRES WITH 3M COMPANY

(TYP)

NOTE 4

(TYP)

NOTE 3, 7

(TYP)

NOTE 1

TROUGH

(TYP)

NOTE 3, 7, WIRING DIAGRAM A

(TYP)

TO FIXTURE

CONNECTION

GROUNDING

(TYP)

NOTE 1

TROUGH

THE LIGHT FIXTURE.

FROM THE JUNCTION BOX TO THE TROUGH AND FROM THE TROUGH TO

" SNAP-IN BUSHING FOR BRANCH CIRCUIT WIRES PASSING 21PROVIDE HEYCO

ELECTRICAL TAP CONNECTORS USED ON ALL BRANCH CIRCUITS.

SUPER 88, 8.5MIL AROUND THE 3M COMPANY SCOTCHLOK SELF-STRIPPING

PROVIDE TWO LAYERS OF 3M COMPANY PREMIUM VINYL ELECTRICAL TAPE,

INSULATED ELECTRICAL SPRING CONNECTOR.

SPLICE TO BALLAST WIRES WITH 3M COMPANY SCOTCHLOK TYPE

COMMUNICATION DOCUMENTS.

FOR COMMUNICATION WIRING AND SPLICING/TAP DETAILS SEE

7/16"

9/32"

2 1/4"

1 19/32"

1 1/8"

3 3/16"

2 1/4"

6 1/2"

2 1/4"

1 1/8"

6 31/32"

8 1/8"

1/2"

3/8"

7/8"

7/8"

BRASS DOWEL

3/8" STIFFENER

RIVETED IN

2 1/8"

1/2" 1 1/4"

7/8"

1/16" 1 7/8"

7/16" 7/32"

1"

5/16"

1/8"

1/2"

1 3/16"

1/2"

5/16"

1"

7/16"

1"

13/32"

JAWS FINISHED ALL OVER

3/8"

4 1/4"

3 1/4"

1 5/8"

1"

3 5/8"

1/2"

2"

1/16" WALL, 3 3/16" LONG3/8"

3 1/4"

1/4"-20

1/4"-20

1"

2"

4"

1/2"

1"3/8"

3/8"

4 5/8" LONG-BRASS3/4"

1/4"-20 BRONZE SWING EYE

BOLT WITH BRASS WING NUT

UPSET END

1'-3"

3/8"

3/4"

2 7/8"

5 1/2"

6"

1/4"

3/8"

5/16"

3/4"

1 1/4"

3/8"

1/2" RO

UN

D

OF

F

ED

GE

S

INSULATING SLEEVE

5/16"*

5 1/2"

ST

EE

L

BO

LT

WIT

H

NU

T.

ST

D

WA

SH

ER,

LO

CK

WA

SH

ER

AN

D

SP

EC.

ST

EE

L

NU

T

1/4"*

3/4"

SQ

R.

AL

L

GA

LV

ANIS

ED

EX

CE

PT

LO

CK

WA

SH

ER.

1/2"

1/2"

3/4"

DIA.

HO

LE

1/8"*

1/16"

L

OC

K

WA

SH

ER5/16"

3/4"

3 3/8" 4"

3/4" DIA. BRASS WASHER

LONG

3/4"X3/4"X1/8"X2 5/8"

1 8"

1 8"

1"

# 125 MICARTA

ANGLE OR EQUAL

1/16"

1/2"

REAM

1 1/2"

#76 MICARTA OR EQUAL

11

16

"SCALE

0

FT.

1 2

BASE 2 1/2'X10 1/4'X 1/2"

3/4"X3/4"X1/8" ANGLE

3/8"

5/8"

1 1/8"

7/8"

3/16"1/2"

3/16"1/8"

5/16"

7/16"

18 GA. PHOS. BRZ.

SPRING CLIP

SPRING CLIP

CLEARANCE HOLE

FOR 1/8" RIVETS

5/16"

1/2"3/16"

31-60 AMPS

REFERENCES

5. FIBERGLASS GLASTIC 1130 EXCEPT AS NOTED.

AMPERES.

RAIL CONNECTIORS FOR FUSE BOXES RATED 31-60

4. NO. 1/0 CABLE SHALL BE USED WITH THE CONTACT

APPROVED INSULATING COMPOUND.

3. ALL COUNTERBORED HOLES TO BE FILLED WITH

OTHERWISE SPECIFIED.

2. ALL COUNTERBORES TO BE ‚" DEEP UNLESS

BRONZE NUTS UNLESS OTHERWISE INDICATED.

1. ALL MACHINE SCREWS #10-24 R'D HD BRONZE WITH

METHOD OF INSTALLING FUSE BOX P-414-609

P-414-607

31-60 AMPERES - DETAILS

FOR CONTACT RAIL TAP

FUSE BOX

A

1 3/4"

7/16" 7/8"

4 1/2"

FUSE CLIP

3/4"

END VIEW OF COVER

2 1/2"

6 1/4"

3 1/8"

1 1/16"

2 1/8"

3/4"

1 1/4"

3 8" DRAIN

HOLE

A

A

PLAN

FUSE TERMINAL

COPPER13/16" 1 1/2"

1/4"-20 TAP

1 9/16"

1 1/8"

3 1/8"

1"

2"

13/16"

1 5/8"

1/8"

5/16"

1/2"

1"

1 5/16"

USE #10-24 TAP

2"

1/2"

1/4"

5/8"

7/8"

1/2"

1/4"

PILOT BLOCK

1 1/4"

COUNTERSUNK

13/16"

NOTES:

COPPER

CABLE TERMINAL

SECTION A-AELEVATION

BOTTOM VIEW OF COVER

COPPER

CABLE FERRULE

STANDARD DRAWING

DRAWN BY

APPROVED BY

DATE :

DRAWING NO.

MANAGEMENT

CAPITAL PROGRAM

DEPARTMENT OF

DESIGNED BY

CHECKED BY


ISSUE

12-04-2003

G. REVES

J. DELLAS P.E.

P.E.

R. DE LA SOLEDAD

C.B. PATEL P.E.

(SIGNED)

(SIGNED)

(SIGNED)

(SIGNED)

12"

CONNECTOR

WATER TIGHT

EQUIPMENT

ELECTRICAL

CONDUIT TO

AS REQUIRED

ELBOWS

CONDULET

CONNECTOR

WATER TIGHT

CAULK & SEAL

THROAT

INSULATED

METALIC CONDUIT, 18" MAXIMUM.

TO CONTACT RAIL (LINE SIDE) SHALL BE IN A FLEXIBLE NON

4. CABLE FROM FUSE BOX TO CONDUIT (LOAD SIDE) AND FUSE BOX

CLEARANCE LINE.

3. FUSE BOX MAY BE LOWERED IF NECESSARY TO KEEP OUTSIDE OF

LOCK WASHERS.

†"x3•" TWO UNIT STAINLESS STEEL EXPANSION BOLTS WITH

2. ALL BRACKETS SHALL BE SECURED TO STRUCTURE BY MEANS OF

1. BRACKETS SHALL BE 1•"x…" HOT DIPPED GALVANIZED STEEL.

REFERENCES:

150 LB RAIL CLAMP P-434-2874

FUSE BOX - 101-200 P-414-608

FUSE BOX - 31-60 AMP P-414-607

FUSE BOX - 30 AMP OR LESS P-414-1576

W

BASE OF RAIL

1"

CAR CLEARANCE LINE

3†"

1' 4ƒ"

ƒ"

1"

3"

2‚"

3"

W

BASE OF RAIL

CAR CLEARANCE LINE

† "X 3•

"

1' 4ƒ"

ƒ"

1"

3"

1†"

4‚" 3†"

-2 UNIT EXPANSION BOLT (STAINLESS STEEL)

A

A

ƒ"

1" 3"11"

CONTACT RAIL

CONTACT RAIL

CONNECTOR

BASE OF RAIL

† "

…

CL

"3' - 3 TO GAUGE LINE

5' - 7 TO OF TRACK

{

CAR CLEARANCE LINE

3†"

1•"

DETERMINE IN FIELD

FUSE BOX

BASE OF RAIL

PROTECTION BOARD

CONTACT RAIL

CONNECTORCONTACT RAIL

CONTACT RAIL

BASE OF RAIL

FUSE BOX THIRD RAIL

PROTECTION BOARD

B

B0 2 4

SCALE : IN.

THIRD RAIL

NEOPRENE SHEATHED #6 AWG

BASE OF RAIL

0 2 4

SCALE : IN.

NOTE 4

NOTE 4

NOTE 4

CONTACT RAIL

150 LB.

CONTACT RAIL

150 LB.

P-414-609

FUSE BOX

METHOD OF INSTALLING

•" LOCK NUT

A

NOTES:

SECTION "B-B"

GENERAL MOUNTING

PROTECTION BOARD BRACKET

TYPE-A BRACKET

TYPE-B BRACKET

ELEVATION A-ATYPE-C BRACKET

IS BETWEEN 5'-9" AND 5'-11"

FROM FACE OF WALL TO > OF TRACK

TO BE USED WHERE DISTANCE "W"

IS BETWEEN 5'-11" AND 6'-2"

FROM FACE OF WALL TO > OF TRACK

TO BE USED WHERE DISTANCE "W"

WALL WITHIN 6'-2" OF > OF TRACK

TO BE USED WHERE THERE IS NO

CLEARANCE LINE

CONSTRUCTION

J280 OR EQUAL

BURNDY RAIL CONNECTOR

•" FLAT WASHER (NARROW GAUGE)

•" HEX. BOLT

BOARD

PROTECTION

FIBERGLASS

BOX

FUSE

BRACKET

PROTECTION BOARD

OR EQUAL)

(FIBERGLASS

NIPPLE

LOCATION OF CABLE

ALTERNATE

BOARD BRACKET

PROTECTION

MATERIAL: 3/8"X1 1/2" STEEL (H.D.G.)

NO. REQUIRED: TWO PER FUSE BOX

12"

7 1/4"

…"

1"2•"3ƒ"

1"

3•

"4‚

"

8ƒ

"

ƒ"

Œ"D

1•"

•"D

2"

STANDARD DRAWING

DRAWN BY

APPROVED BY

DATE :

DRAWING NO.

MANAGEMENT

CAPITAL PROGRAM

DEPARTMENT OF

DESIGNED BY

CHECKED BY


ISSUE

12-04-2003

G. REVES

J. DELLAS P.E.

P.E.

R. DE LA SOLEDAD

C.B. PATEL P.E.

(SIGNED)

(SIGNED)

(SIGNED)

(SIGNED)

.56R

13 O

13 O

1.12 DIA

P-434-2874

RAIL CONNECTORS

A

3. GRIND THE RAIL WHEN THE CLAMP COMES INTO CONTACT WITH IT.

2. MATERIAL OR CLAMPS SHALL BE APPROVED CAST COPPER ALLOY.

1. ALL DIMENSIONS ARE IN INCHES.

SECTION A-A

NOTES

RAIL

RUNNING

100 LB.

CONTACT RAIL

150 LB.

.44"

1.25"

1.44"

1.25"

1.50"

LOCKWASHER

WASHER & SKPRF.

HEX. BOLT FLAT-

Š"x†" DURIUM

1.81"

.12"

.42"

2.00"

.44"

.25"

NUT & SPLIT LOCK WASHER

• x 8 HEX. DURIUM BOLT,

1.75"

.44"

2.00".45"

.50"

.88"

LOCKWASHER

WASHER & SKPRF.

HEX. BOLT FLAT-

Š"x†" DURIUM

NUT & SPLIT LOCK WASHER

• x 7 HEX. DURIUM BOLT,

.12"

.62"

2.19"

.44"

.25"2.00"

.50"

AA

1.50"

1.25"

2.19"1.50"

2.19"

STANDARD DRAWING

DRAWN BY

APPROVED BY

DATE :

DRAWING NO.

MANAGEMENT

CAPITAL PROGRAM

DEPARTMENT OF

DESIGNED BY

CHECKED BY


ISSUE

12-04-2003

G. REVES

J. DELLAS P.E.

P.E.

R. DE LA SOLEDAD

C.B. PATEL P.E.

(SIGNED)

(SIGNED)

(SIGNED)

(SIGNED)

1.

2.

NOTE-2.NOTE-2.

NOTE-3.

NOTE-4.

5.

6.

7.

3.

4.

SIGNAGE

0 2 4

FTSCALE

0 2 4

FTSCALE 0 2 4

FTSCALE

NOTE-3.

LED DOWN LIGHT DETAILSLOCATION..MOUNTING FOOTADJ & LOCKS.S. SCREW TO

1.5

8

BOTTOM VIEW

OPTICS: WIDE BEAMCOLOR TEMP TO BE SPECIFIED.1W X 17 LEDS

CLEAR 50% DR ACRYLIC LENS

ALUMINUM BODYANODIZED EXTRUDED CLEAR

MOUNTING FEET8GA ALUMINUM

W/ STRAIN RELIEF.4ft CABLE PROVIDED

2.1

0

2.00

34.75

35.13

1.1

2

4.0

0

1.00

1.1

2

.38

.19

2.07

NTS

STREET ELEVATOR FRONT (TYP.) STREET ELEVATOR SIDE (TYP.)

STREET ELEVATOR PLAN (TYP.)

NOTES:

ALL CONDUITS AND FITTING FOR THE LED LIGHTINGS SHALL BE STAINLESS STEEL.

INSTALLATION OF THE FIXTURES.

FOR INSPECTION AND APPROVAL BY THE ENGINEERS PRIOR TO MANUFACTURING AND

CONTRACTOR SHALL INSTALL MOCK-UPS OF LED DOWN LIGHT & CANOPY LED STRIPS.

ALL LED LIGHTING SHALL BE CONTROLLED BY THE PHOTOCELL.

ARCHITECTURE DRAWING FOR DETAILS.

OF THE CANOPY STAINLESS STEEL STRUCTURE BEAMS. SEE ALSO

CAT. # 24-X35-S-4F-NC-00 PT. LED STRIPS MOUNT ALONG THE SIDES

MANUFACTURED BY ILIGHT TECHNOLOGIES WHITE 2X SERIES

PROVIDE 14 SETS OF PLEXINEON LED STRIPS UNDER THE CANOPY,

FOR SIGNAGE ENCLOSURE, SEE ARCHITECTURE DRAWING FOR DETAILS.

THE LED DRIVER MANUFACTURED BY DESIGNPLAN CAT. # PT-DB-CV1-2X100.

INSIDE THE SIGNAGE ENCLOSURE, PROVIDE MOUNTING HARDWARE AS REQUIRED.

MOUNT 4X100W 24VDC LED DRIVERS WITH TWO SPECIAL MADE ENCLOSURES

DELETED

WITH THE BOTTOM OF THE ENCLOSURE. SEE ALSO ARCHITECTURE DRAWINGS FOR DETAILS.

BEHIND THE STATION SIGNAGE. THE BOTTOM OF THE LED DOWN LIGHT SHALL BE IN LINE

LIGHTING CAT. # CV1-L-AC-NO-96-3-X-A PT. MOUNT LED DOWN LIGHT INSIDE ENCLOSURE

PROVIDE LED DOWN LIGHT IN FRONT OF THE ELEVATOR DOOR, MANUFACTURED BY DESIGNPLAN

R:\61465\grand_street\ele\standards\streetlight.dgn 02-MAR-2020 14:07 sandraPRINT AS OF

DATE :

DRAWING NO.

MANAGEMENT

CAPITAL PROGRAM

DEPARTMENT OF

New York City

Transit Authority

CONTRACT A-37151

IN THE FIVE BOROUGHS OF NYC - PACKAGE A

AT TWENTY-THREE STATIONS

DESIGN BUILD SERVICES FOR ACCESSIBILITY UPGRADES

02/12/2020

ELECTRICAL

L-

scope of work notes - home | mta

Documents