safety data sheet · safety data sheet 1. identification product identifier 3-36® multi-purpose...
TRANSCRIPT
SAFETY DATA SHEET
1. Identification
Product identifier 3-36® Multi-Purpose Lubricant & Corrosion Inhibitor
Other means of identification
Product code 03004, 03005
Recommended use Multi-purpose lubricant
Recommended restrictions None known.
Manufacturer/Importer/Supplier/Distributor information
Manufactured or sold by:
Company name CRC Industries, Inc.
Address 885 Louis Dr.
Warminster, PA 18974 US
Telephone
General Information 215-674-4300
Technical
Assistance
800-521-3168
Customer Service 800-272-4620
24-Hour Emergency 800-424-9300 (US)
(CHEMTREC) 703-527-3887 (International)
Website www.crcindustries.com
2. Hazard(s) identification
Category 1Flammable aerosolsPhysical hazards
Compressed gasGases under pressure
Category 2Skin corrosion/irritationHealth hazards
Category 3 narcotic effectsSpecific target organ toxicity, single exposure
Category 1Aspiration hazard
Category 2Hazardous to the aquatic environment, acutehazard
Environmental hazards
Not classified.OSHA defined hazards
Label elements
Signal word Danger
Hazard statement Extremely flammable aerosol. Contains gas under pressure; may explode if heated. May be fatal ifswallowed and enters airways. Causes skin irritation. May cause drowsiness or dizziness.
Precautionary statement
Prevention Keep away from heat/sparks/open flames/hot surfaces. - No smoking. Do not spray on an openflame or other ignition source. Do not apply while equipment is energized. Pressurized container:Do not pierce or burn, even after use. Extinguish all flames, pilot lights and heaters. Vapors willaccumulate readily and may ignite. Use only with adequate ventilation; maintain ventilation duringuse and until all vapors are gone. Open doors and windows or use other means to ensure a freshair supply during use and while product is drying. If you experience any symptoms listed on thislabel, increase ventilation or leave the area. Avoid breathing gas, mist or vapor. Wear protectivegloves. Wash hands thoroughly after handling.
Response If swallowed: Immediately call a poison center/doctor. Do NOT induce vomiting. If on skin: Washwith plenty of water. If skin irritation occurs: Get medical attention. Take off contaminated clothingand wash before reuse. If inhaled: Remove person to fresh air and keep comfortable forbreathing. Call a poison center/doctor if you feel unwell.
Storage Store in a well-ventilated place. Store locked up. Protect from sunlight. Do not expose totemperatures exceeding 50°C/122°F. Exposure to high temperature may cause can to burst.
Disposal Dispose of contents/container in accordance with local/regional/national regulations.
Hazard(s) not otherwise
classified (HNOC)None known.
1 / 8
Material name: 3-36® Multi-Purpose Lubricant & Corrosion Inhibitor
1724 Version #: 01 Issue date: 11-11-2013
SDS US
http://www.techni-tool.com
http://www.techni-tool.com
Supplemental information
Not applicable.
3. Composition/information on ingredients
Mixtures
CAS number %Chemical name Common name and synonyms
64742-47-8Distillates (petroleum),Hydrotreated Light
60 - 70
64741-88-4Distillates (petroleum),Solvent-refined Heavy Paraffinic
10 - 20
123-95-5n-Butyl stearate 3 - 5
124-38-9Carbon dioxide 1 - 3
61788-89-4Fatty Acids, C18-unsatd., Dimers 1 - 3
8009-03-8Petrolatum 1 - 3
5989-27-5d-Limonene < 0.2
Specific chemical identity and/or percentage of composition has been withheld as a trade secret.
4. First-aid measures
Inhalation Remove victim to fresh air and keep at rest in a position comfortable for breathing. Call a POISONCENTER or doctor/physician if you feel unwell.
Skin contact Remove contaminated clothing. Wash off with soap and plenty of water. If skin irritation occurs:Get medical advice/attention.
Eye contact Rinse with water. Get medical attention if irritation develops and persists.
Ingestion Call a physician or poison control center immediately. Rinse mouth. Do not induce vomiting. Ifvomiting occurs, keep head low so that stomach content doesn't get into the lungs. Aspiration maycause pulmonary edema and pneumonitis.
Most important
symptoms/effects, acute and
delayed
Vapors have a narcotic effect and may cause headache, fatigue, dizziness and nausea. Maycause drowsiness or dizziness. Irritant effects.
Indication of immediate
medical attention and special
treatment needed
Provide general supportive measures and treat symptomatically.
General information Ensure that medical personnel are aware of the material(s) involved, and take precautions toprotect themselves. If you feel unwell, seek medical advice (show the label where possible). Washcontaminated clothing before reuse.
5. Fire-fighting measures
Suitable extinguishing media Alcohol resistant foam. Water. Water spray. Dry powder. Carbon dioxide (CO2).
Unsuitable extinguishing
media
None known.
Specific hazards arising from
the chemical
Contents under pressure. Pressurized container may explode when exposed to heat or flame.
Special protective equipment
and precautions for firefighters
Firefighters must use standard protective equipment including flame retardant coat, helmet withface shield, gloves, rubber boots, and in enclosed spaces, SCBA.
Fire-fighting
equipment/instructionsIn case of fire: Stop leak if safe to do so. Do not move cargo or vehicle if cargo has been exposedto heat. Move containers from fire area if you can do so without risk. Use water spray to coolunopened containers. Containers should be cooled with water to prevent vapor pressure build up.For massive fire in cargo area, use unmanned hose holder or monitor nozzles, if possible. If not,withdraw and let fire burn out.
General fire hazards Extremely flammable aerosol.
6. Accidental release measures
Personal precautions,
protective equipment and
emergency procedures
Keep people away from and upwind of spill/leak. Keep out of low areas. Wear appropriatepersonal protective equipment. Do not touch damaged containers or spilled material unlesswearing appropriate protective clothing. Ventilate closed spaces before entering them. Localauthorities should be advised if significant spillages cannot be contained.
Methods and materials for
containment and cleaning up
Eliminate all ignition sources (no smoking, flares, sparks, or flames in immediate area). Keepcombustibles (wood, paper, oil, etc.) away from spilled material. Stop leak if you can do so withoutrisk. Move the cylinder to a safe and open area if the leak is irreparable. Use water spray to reducevapors or divert vapor cloud drift. Following product recovery, flush area with water.
Environmental precautions Avoid discharge into drains, water courses or onto the ground.
2 / 8
Material name: 3-36® Multi-Purpose Lubricant & Corrosion Inhibitor
1724 Version #: 01 Issue date: 11-11-2013
SDS US
http://www.techni-tool.com
http://www.techni-tool.com
7. Handling and storage
Precautions for safe handling Pressurized container: Do not pierce or burn, even after use. Do not use if spray button is missingor defective. Do not spray on a naked flame or any other incandescent material. Do not smokewhile using or until sprayed surface is thoroughly dry. Do not cut, weld, solder, drill, grind, orexpose containers to heat, flame, sparks, or other sources of ignition. Use caution aroundenergized equipment. The metal container will conduct electricity if it contacts a live source. Thismay result in injury to the user from electrical shock and/or flash fire. Avoid breathing mist orvapor. Avoid breathing gas. Avoid contact with skin. Avoid contact with eyes. Avoid prolongedexposure. Use only in well-ventilated areas. Wear appropriate personal protective equipment.Wash hands thoroughly after handling. Observe good industrial hygiene practices. For productusage instructions, please see the product label.
Conditions for safe storage,
including any incompatibilities
Level 3 Aerosol.
Store in a well-ventilated place. Pressurized container. Protect from sunlight and do not expose totemperatures exceeding 50°C/122 °F. Do not puncture, incinerate or crush. Keep away from heat,sparks and open flame. This material can accumulate static charge which may cause spark andbecome an ignition source.
8. Exposure controls/personal protection
Occupational exposure limits
U.S. - OSHA
ValueComponents FormType
TWA 5 mg/m3 RespirableFatty Acids, C18-unsatd.,Dimers (CAS 61788-89-4)
US. OSHA Table Z-1 Limits for Air Contaminants (29 CFR 1910.1000)
ValueComponents FormType
PEL 9000 mg/m3Carbon dioxide (CAS124-38-9)
5000 ppm
PEL 5 mg/m3 Mist.Distillates (petroleum),Solvent-refined HeavyParaffinic (CAS64741-88-4)
2000 mg/m3
500 ppm
PEL 5 mg/m3 Mist.Petrolatum (CAS8009-03-8)
ACGIH
ValueComponents FormType
STEL 10 mg/m3 RespirableFatty Acids, C18-unsatd.,Dimers (CAS 61788-89-4)
TWA 5 mg/m3 Respirable
US. ACGIH Threshold Limit Values
ValueComponents FormType
STEL 30000 ppmCarbon dioxide (CAS124-38-9)
TWA 5000 ppm
TWA 5 mg/m3 Inhalable fraction.Distillates (petroleum),Solvent-refined HeavyParaffinic (CAS64741-88-4)
TWA 10 mg/m3n-Butyl stearate (CAS123-95-5)
TWA 5 mg/m3 Inhalable fraction.Petrolatum (CAS8009-03-8)
US. NIOSH: Pocket Guide to Chemical Hazards
ValueComponents FormType
STEL 54000 mg/m3Carbon dioxide (CAS124-38-9)
30000 ppm
TWA 9000 mg/m3
5000 ppm
TWA 100 mg/m3Distillates (petroleum),Hydrotreated Light (CAS64742-47-8)
3 / 8
Material name: 3-36® Multi-Purpose Lubricant & Corrosion Inhibitor
1724 Version #: 01 Issue date: 11-11-2013
SDS US
http://www.techni-tool.com
http://www.techni-tool.com
US. NIOSH: Pocket Guide to Chemical Hazards
ValueComponents FormType
STEL 10 mg/m3 Mist.Distillates (petroleum),Solvent-refined HeavyParaffinic (CAS64741-88-4)
TWA 5 mg/m3 Mist.
STEL 10 mg/m3 Mist.Petrolatum (CAS8009-03-8)
TWA 5 mg/m3 Mist.
US. AIHA Workplace Environmental Exposure Level (WEEL) Guides
ValueComponents Type
TWA 165.5 mg/m3d-Limonene (CAS5989-27-5)
30 ppm
Biological limit values No biological exposure limits noted for the ingredient(s).
Appropriate engineering
controls
Good general ventilation (typically 10 air changes per hour) should be used. Ventilation ratesshould be matched to conditions. If applicable, use process enclosures, local exhaust ventilation,or other engineering controls to maintain airborne levels below recommended exposure limits. Ifexposure limits have not been established, maintain airborne levels to an acceptable level.
Individual protection measures, such as personal protective equipment
Eye/face protection Wear eye/face protection. Wear safety glasses with side shields (or goggles).
Skin protection
Hand protection Wear protective gloves such as neoprene or nitrile.
Other Wear appropriate chemical resistant clothing.
Respiratory protection Wear positive pressure self-contained breathing apparatus (SCBA). Air monitoring is needed todetermine actual employee exposure levels.
Thermal hazards Wear appropriate thermal protective clothing, when necessary.
General hygiene
considerations
When using, do not eat, drink or smoke. Always observe good personal hygiene measures, suchas washing after handling the material and before eating, drinking, and/or smoking. Routinelywash work clothing and protective equipment to remove contaminants.
9. Physical and chemical properties
Appearance
Physical state Liquid.
Form Aerosol.
Color Blue green.
Odor Pleasant.
Odor threshold Not available.
pH Not available.
Melting point/freezing point -72.4 °F (-58 °C) estimated
Initial boiling point and boiling
range
380 °F (193.3 °C) estimated
Flash point 192 °F (88.9 °C) Tag Closed Cup
Evaporation rate Slow
Flammability (solid, gas) Not available.
Upper/lower flammability or explosive limits
Flammability limit - lower
(%)
0.6 % estimated
Flammability limit - upper
(%)
5.5 % estimated
Vapor pressure 1431 hPa estimated
Vapor density > 1 (air = 1)
Relative density 0.84 estimated
Solubility (water) Negligible.
Partition coefficient
(n-octanol/water)
Not available.
Auto-ignition temperature 456.8 °F (236 °C) estimated
Decomposition temperature Not available.
4 / 8
Material name: 3-36® Multi-Purpose Lubricant & Corrosion Inhibitor
1724 Version #: 01 Issue date: 11-11-2013
SDS US
http://www.techni-tool.com
http://www.techni-tool.com
Viscosity (kinematic) Not available.
Percent volatile 88.6 % estimated
10. Stability and reactivity
Reactivity The product is stable and non-reactive under normal conditions of use, storage and transport.
Chemical stability Material is stable under normal conditions.
Possibility of hazardous
reactions
No dangerous reaction known under conditions of normal use.
Conditions to avoid Heat, flames and sparks. Avoid temperatures exceeding the flash point. Contact with incompatiblematerials.
Incompatible materials Strong oxidizing agents.
Hazardous decomposition
products
Carbon oxides. Sulfur oxides. Hydrocarbons.
11. Toxicological information
Information on likely routes of exposure
Ingestion May be fatal if swallowed and enters airways.
Inhalation Vapors have a narcotic effect and may cause headache, fatigue, dizziness and nausea.Prolonged inhalation may be harmful.
Skin contact Causes skin irritation.
Eye contact Direct contact with eyes may cause temporary irritation.
Symptoms related to the
physical, chemical and
toxicological characteristics
Symptoms of overexposure may be headache, dizziness, tiredness, nausea and vomiting. Irritanteffects.
Information on toxicological effects
Acute toxicity May be fatal if swallowed and enters airways. Narcotic effects.
Test ResultsProduct Species
3-36® Multi-Purpose Lubricant & Corrosion Inhibitor
LD50 Rabbit
Dermal
Acute
2818.8381 mg/kg estimated
LC50 Rat
Inhalation
116.664 mg/l estimated
LD50 Rat
Oral
6740.1777 mg/kg estimated
LD50 Rat
Oral
Subchronic
1166.0905 g/kg, 14 days estimated
Skin corrosion/irritation Causes skin irritation.
Serious eye damage/eye
irritation
Direct contact with eyes may cause temporary irritation.
Respiratory sensitization Not available.
Skin sensitization This product is not expected to cause skin sensitization.
Germ cell mutagenicity No data available to indicate product or any components present at greater than 0.1% aremutagenic or genotoxic.
Carcinogenicity This product is not considered to be a carcinogen by IARC, ACGIH, NTP, or OSHA.
IARC Monographs. Overall Evaluation of Carcinogenicity
d-Limonene (CAS 5989-27-5) 3 Not classifiable as to carcinogenicity to humans.
Reproductive toxicity This product is not expected to cause reproductive or developmental effects.
Specific target organ toxicity -
single exposure
Narcotic effects.
Specific target organ toxicity -
repeated exposure
Not classified.
Aspiration hazard May be fatal if swallowed and enters airways.
Chronic effects Prolonged exposure may cause chronic effects.
5 / 8
Material name: 3-36® Multi-Purpose Lubricant & Corrosion Inhibitor
1724 Version #: 01 Issue date: 11-11-2013
SDS US
http://www.techni-tool.com
http://www.techni-tool.com
12. Ecological information
Ecotoxicity The product is not classified as environmentally hazardous. However, this does not exclude thepossibility that large or frequent spills can have a harmful or damaging effect on the environment.
Product Test ResultsSpecies
3-36® Multi-Purpose Lubricant & Corrosion Inhibitor
Acute
LC50Fish 4916.4028 ppm, 96 hours estimatedFish
Components Test ResultsSpecies
Distillates (petroleum), Hydrotreated Light (CAS 64742-47-8)
Aquatic
Acute
LC50Fish 2.2 mg/l, 96 hoursBluegill (Lepomis macrochirus)
d-Limonene (CAS 5989-27-5)
Aquatic
EC50Crustacea 69.6 mg/l, 48 hoursWater flea (Daphnia pulex)
LC50Fish 0.619 - 0.796 mg/l, 96 hoursFathead minnow (Pimephales promelas)
Fatty Acids, C18-unsatd., Dimers (CAS 61788-89-4)
Acute
NOELCrustacea 1000 mg/l, 48 hours loading rate WAFDaphnia
NOELFish 1000 mg/l, 96 hours loading rate WAFFish
Persistence and degradability No data is available on the degradability of this product.
Bioaccumulative potential No data available.
Partition coefficient n-octanol / water (log Kow)
d-Limonene 4.232
Fatty Acids, C18-unsatd., Dimers 1 - 2.5, logKow
Mobility in soil No data available.
Other adverse effects No other adverse environmental effects (e.g. ozone depletion, photochemical ozone creationpotential, endocrine disruption, global warming potential) are expected from this component.
13. Disposal considerations
Disposal of waste from
residues / unused products
The dispensed liquid product is not a RCRA hazardous waste (See 40 CFR Part 261.20 - 261.33).Consult authorities before disposal. Contents under pressure. Do not puncture, incinerate or crush.Do not allow this material to drain into sewers/water supplies. Do not contaminate ponds,waterways or ditches with chemical or used container. Dispose of contents/container inaccordance with local/regional/national regulations.
Hazardous waste code Not regulated.
Contaminated packaging Do not re-use empty containers.
14. Transport information
DOT
UN1950UN number
Aerosols, flammable, limited quantityUN proper shipping name
2.1Class
Transport hazard class(es)
-Subsidiary risk
2.1Label(s)
Not applicable.Packing group
Not available.Special precautions for user
306Packaging exceptions
NonePackaging non bulk
NonePackaging bulk
IATA
UN1950UN number
Aerosols, flammable, limited quantityUN proper shipping name
2.1Class
Transport hazard class(es)
-Subsidiary risk
Not applicable.Packing group
No.Environmental hazards
2LERG Code
6 / 8
Material name: 3-36® Multi-Purpose Lubricant & Corrosion Inhibitor
1724 Version #: 01 Issue date: 11-11-2013
SDS US
http://www.techni-tool.com
http://www.techni-tool.com
Not available.Special precautions for user
Allowed.Passenger and cargo
aircraft
Other information
Allowed.Cargo aircraft only
IMDG
UN1950UN number
AEROSOLS, LIMITED QUANTITYUN proper shipping name
2Class
Transport hazard class(es)
-Subsidiary risk
Not applicable.Packing group
No.Marine pollutant
Environmental hazards
F-D, S-UEmS
Not available.Special precautions for user
15. Regulatory information
US federal regulations This product is a "Hazardous Chemical" as defined by the OSHA Hazard CommunicationStandard, 29 CFR 1910.1200.
TSCA Section 12(b) Export Notification (40 CFR 707, Subpt. D)
Not regulated.
SARA 304 Emergency release notification
Not regulated.
US. OSHA Specifically Regulated Substances (29 CFR 1910.1001-1050)
Not listed.
US EPCRA (SARA Title III) Section 313 - Toxic Chemical: Listed substance
Not listed.
CERCLA Hazardous Substance List (40 CFR 302.4)
Not listed.
CERCLA Hazardous Substances: Reportable quantity
Not listed.
Spills or releases resulting in the loss of any ingredient at or above its RQ require immediate notification to the NationalResponse Center (800-424-8802) and to your Local Emergency Planning Committee.
Clean Air Act (CAA) Section 112 Hazardous Air Pollutants (HAPs) List
Not regulated.
Clean Air Act (CAA) Section 112(r) Accidental Release Prevention (40 CFR 68.130)
Not regulated.
Safe Drinking Water Act
(SDWA)
Not regulated.
Food and Drug
Administration (FDA)
Not regulated.
Superfund Amendments and Reauthorization Act of 1986 (SARA)
Section 311/312
Hazard categories
Immediate Hazard - YesDelayed Hazard - NoFire Hazard - YesPressure Hazard - YesReactivity Hazard - No
SARA 302 Extremely
hazardous substance
No
US state regulations
US. New Jersey RTK - Substances: Listed substance
Carbon dioxide (CAS 124-38-9)
US. Massachusetts RTK - Substance List
Carbon dioxide (CAS 124-38-9)
US. Pennsylvania RTK - Hazardous Substances
Carbon dioxide (CAS 124-38-9)
Distillates (petroleum), Hydrotreated Light (CAS 64742-47-8)
US. Rhode Island RTK
None.
7 / 8
Material name: 3-36® Multi-Purpose Lubricant & Corrosion Inhibitor
1724 Version #: 01 Issue date: 11-11-2013
SDS US
http://www.techni-tool.com
http://www.techni-tool.com
US. California Proposition 65
California Safe Drinking Water and Toxic Enforcement Act of 1986 (Proposition 65): This material is not known to containany chemicals currently listed as carcinogens or reproductive toxins.
Volatile organic compounds (VOC) regulations
EPA
VOC content (40 CFR
51.100(s))
97.5 %
Consumer products
(40 CFR 59, Subpt. C)
Not regulated
State
Consumer products This product is regulated as a Multi-Purpose Lubricant. This product is compliant for use in all 50states.
VOC content (CA) 0 %
VOC content (OTC) 0 %
International Inventories
Country(s) or region Inventory name On inventory (yes/no)*
NoAustralia Australian Inventory of Chemical Substances (AICS)
NoCanada Domestic Substances List (DSL)
NoCanada Non-Domestic Substances List (NDSL)
NoChina Inventory of Existing Chemical Substances in China (IECSC)
NoEurope European Inventory of Existing Commercial ChemicalSubstances (EINECS)
NoEurope European List of Notified Chemical Substances (ELINCS)
NoJapan Inventory of Existing and New Chemical Substances (ENCS)
NoKorea Existing Chemicals List (ECL)
NoNew Zealand New Zealand Inventory
NoPhilippines Philippine Inventory of Chemicals and Chemical Substances(PICCS)
YesUnited States & Puerto Rico Toxic Substances Control Act (TSCA) Inventory
*A "Yes" indicates that all components of this product comply with the inventory requirements administered by the governing country(s)A "No" indicates that one or more components of the product are not listed or exempt from listing on the inventory administered by the governingcountry(s).
16. Other information, including date of preparation or last revision
Issue date 11-11-2013
Prepared by Allison Cho
Version # 01
Further information CRC # 510F
HMIS® ratings Health: 1Flammability: 3Physical hazard: 0Personal protection: B
NFPA ratings Health: 1Flammability: 3Instability: 0
Disclaimer The information contained in this document applies to this specific material as supplied. It may notbe valid for this material if it is used in combination with any other materials. This information isaccurate to the best of CRC Industries' knowledge or obtained from sources believed by CRC tobe accurate. Before using any product, read all warnings and directions on the label. For furtherclarification of any information contained on this (M)SDS consult your supervisor, a health & safetyprofessional, or CRC Industries.
8 / 8
Material name: 3-36® Multi-Purpose Lubricant & Corrosion Inhibitor
1724 Version #: 01 Issue date: 11-11-2013
SDS US
http://www.techni-tool.com
http://www.techni-tool.com