safety check course...check shifter flappy paddle then check if the red light is on when you push...
TRANSCRIPT
Safety Check-CourseIN THIS SLIDESHOW YOU WILL TAKE PART OF HOW A SAFETY CHECK
IS PREFORMED CORRECTLY
CASTER - ENGINEERS IN THE FRONT SEAT
The list to perform a Safety
CheckThe safety check is divided into fiveparts, every part has to be approved in order for the safety check to be completed.
Three parts includes a check of the pit area and upper platform which is around the simulator.
Two parts include the start up and safety check which is to be made on the computer.
And the last driving check is made witha driver in the drivers seat.
Let´s begin!
CASTER - ENGINEERS IN THE FRONT SEAT
Pit area
CASTER - ENGINEERS IN THE FRONT SEAT
Make sure that the white spot on the pawn is aligned to the white spot on the ground everywhere around on all three of the attachments
CASTER - ENGINEERS IN THE FRONT SEAT
1. Inspect ground attachment bolts
Same as previous, make sure that the white spot on very bolt is near the white spot on the plate, to make sure no bolt has loosened up.
CASTER - ENGINEERS IN THE FRONT SEAT
2. Inspect actuator fixation (top & bottom)
Top Bottom
Check if wiring and connectors are attached and not moving except around its attachment.
CASTER - ENGINEERS IN THE FRONT SEAT
3. Inspect wiring & connectors of all actuators
4. Inspect computer cabinet
CASTER - ENGINEERS IN THE FRONT SEAT
Make sure the computer cabninets are in the right position
5. Inspect stand and its fixation
CASTER - ENGINEERS IN THE FRONT SEAT
6. Inspect access bridge and its fixation
CASTER - ENGINEERS IN THE FRONT SEAT
There is no bridge, therefore it should look like the picture to the left.
6. Inspect pedalbox wiring & connectors7. Inspect pedalbox fixation
CASTER - ENGINEERS IN THE FRONT SEAT
See if the pedals are fixed and the wiring and connectors are attached.
66
8. Check brake system for oil leaks9. Inspect even brake pedal travel
CASTER - ENGINEERS IN THE FRONT SEAT
Oil leaks
Obs! Check for oil leaks under both cylinders
9
8
10. Inspect throttle pedal endstops11. Inspect clutch pedal endstops
CASTER - ENGINEERS IN THE FRONT SEAT
10 11
12. Inspect screen attachements
CASTER - ENGINEERS IN THE FRONT SEAT
Make sure the screens are still attached – not moving.
Upper platform
CASTER - ENGINEERS IN THE FRONT SEAT
1. Inspect general condition of seat and fixation2. Inspect seatbelt and attachment functioning
CASTER - ENGINEERS IN THE FRONT SEAT
Attachments
Attachments
2
3. Inspect subwoofer underneeth the seat
CASTER - ENGINEERS IN THE FRONT SEAT
Make sure that the subwoofer is fix and no screws has come lose.
4. Inspect seating position adjuster
CASTER - ENGINEERS IN THE FRONT SEAT
Check the position adjuster.
5. Inspect steering wheel6. Inspect general condition of H-pattern shifter7. Inspect fixation of H-pattern to upper platform8. Clean upper platform
CASTER - ENGINEERS IN THE FRONT SEAT
Check shifter flappy paddle
Then check if the red light is on when you push the flappy paddle.
H-pattern shifter
5
7
Start up
CASTER - ENGINEERS IN THE FRONT SEAT
1. Switch on motion system2. Realese E-stop and press red reset button3. Start operator computer
CASTER - ENGINEERS IN THE FRONT SEAT
Switch on motion system
This is how it looks when the E-stop is realesed and the red button is pushed(not shining)
Operator computer
1
23
4. Start Session Manager on desktop
CASTER - ENGINEERS IN THE FRONT SEAT
5. Start all computers
CASTER - ENGINEERS IN THE FRONT SEAT
They can also be started trough ”Session manager”.
6. Check if all computers have Racer running7. Start a new heat and select demo (no driver)
CASTER - ENGINEERS IN THE FRONT SEAT
6. If Racer is running then all the screens on the simulator have a black background withthe Chalmers logo on the middle screen
7.1
7.2
8. Inspect if motion is properly working
CASTER - ENGINEERS IN THE FRONT SEAT
Motion is when the simulator moves while driving. It can be turned off so you can drive without movement.
The motion can be checked by listening for noise and see that the movement is as expected
1. Check if simulator comes up OK 2. Check the car and track loads OK3. Check if spectator view is OK4. Check if the platform moves OK
CASTER - ENGINEERS IN THE FRONT SEAT
What to check while testing demo
Driving check
CASTER - ENGINEERS IN THE FRONT SEAT
Driving Check for test driver
CASTER - ENGINEERS IN THE FRONT SEAT
1. Test motion (It acts normal)2. Test steering (Force feedback)3. Test pedals4. Test shift pedals and manual H-pattern gearbox5. Check audio system
Let´s go!
CASTER - ENGINEERS IN THE FRONT SEAT