s-presso - asusdlcdnet.asus.com/pub/asus/barebone/spresso/j1686_spresso...ribbon cable to pin 1....
TRANSCRIPT
-
® S-presso
-
i ii ii ii ii i
Copyright© 2004 ASUSTeK COMPUTER INC. All Rights Reserved.
-
i i ii i ii i ii i ii i i
-
i vi vi vi vi v
-
vvvvv
-
v iv iv iv iv i
Federal Communications Commission StatementFederal Communications Commission StatementFederal Communications Commission StatementFederal Communications Commission StatementFederal Communications Commission Statement
This device complies with Part 15 of the FCC Rules. Operation is subject tothe following two conditions:
• This device may not cause harmful interference, and
• This device must accept any interference received including interferencethat may cause undesired operation.
This equipment has been tested and found to comply with the limits for aClass B digital device, pursuant to Part 15 of the FCC Rules. These limits aredesigned to provide reasonable protection against harmful interference in aresidential installation. This equipment generates, uses and can radiate radiofrequency energy and, if not installed and used in accordance withmanufacturer’s instructions, may cause harmful interference to radiocommunications. However, there is no guarantee that interference will notoccur in a particular installation. If this equipment does cause harmfulinterference to radio or television reception, which can be determined byturning the equipment off and on, the user is encouraged to try to correctthe interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment to an outlet on a circuit different from that towhich the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Canadian Department of CommunicationsCanadian Department of CommunicationsCanadian Department of CommunicationsCanadian Department of CommunicationsCanadian Department of CommunicationsStatementStatementStatementStatementStatement
This digital apparatus does not exceed the Class B limits for radio noiseemissions from digital apparatus set out in the Radio InterferenceRegulations of the Canadian Department of Communications.
This class B digital apparatus compl ies with Canadian ICES-This class B digital apparatus compl ies with Canadian ICES-This class B digital apparatus compl ies with Canadian ICES-This class B digital apparatus compl ies with Canadian ICES-This class B digital apparatus compl ies with Canadian ICES-003.003.003.003.003.
The use of shielded cables for connection of the monitor to thegraphics card is required to assure compliance with FCCregulations. Changes or modifications to this unit not expresslyapproved by the party responsible for compliance could void theuser’s authority to operate this equipment.
-
v i iv i iv i iv i iv i i
Lithium-Ion Battery WarningCAUTION: Danger of explosion if battery is incorrectly replaced.Replace only with the same or equivalent type recommended bythe manufacturer. Dispose of used batteries according to themanufacturerís instructions.
VORSICHT: Explosionsgetahr bei unsachgemäßen Austausch derBatterie. Ersatz nur durch denselben oder einem vom Herstellerempfohlenem ähnljchen Typ. Entsorgung gebrauchter Batteriennach Angaben des Herstellers.
LASER PRODUCT WARNING
CLASS 1 LASER PRODUCT
-
v i i iv i i iv i i iv i i iv i i i
Safeguards
-
i xi xi xi xi x
-
xxxxx
-
1 - 21 - 21 - 21 - 21 - 2
®
®
1
2 5
6
7
3
4
-
1 - 31 - 31 - 31 - 31 - 3
8
9
1
2
12 13 14
10
11
5
6
7
3
15 16
4
-
1 - 41 - 41 - 41 - 41 - 4
-
1 - 51 - 51 - 51 - 51 - 5
®
®
® ®
®
®
17
18
19
20
21
22
23 24 25 26
-
1 - 61 - 61 - 61 - 61 - 6
1
2
4
3
5
10
9
6
7
8
11 12 171613 14 15 18
-
1 - 71 - 71 - 71 - 71 - 7
-
1 - 81 - 81 - 81 - 81 - 8
12
4
3
5
68
7
-
1 - 91 - 91 - 91 - 91 - 9
1 2 3 4 5 6 7
8 9 10
®
11 12
-
1 -101 -101 -101 -101 -10
-
2 - 22 - 22 - 22 - 22 - 2
P4P8T ®
P4P8T Onboard LED
SB_PWR
ONStandbyPower
OFFPowered
Off
-
2 - 32 - 32 - 32 - 32 - 3
-
2 - 42 - 42 - 42 - 42 - 4
-
2 - 52 - 52 - 52 - 52 - 5
-
2 - 62 - 62 - 62 - 62 - 6
®
®
1
2
3
-
2 - 72 - 72 - 72 - 72 - 7
2
1
35
4
-
2 - 82 - 82 - 82 - 82 - 8
1
2
3
-
2 - 92 - 92 - 92 - 92 - 9
256MB Samsung M368L3223DTM-CC4 Samsung K4H560838D-TCC4
256MB Samsung M368L3223ETM-CCC Samsung K4H560838E-TCCC
512MB Samsung M368L6432ETM-CCC Samsung K4H560838E-TCCC
256MB Infineon HYS64D32300GU-5-B Infineon HYB25D256800BT-5B
512MB Infineon HYS64D64320GU-5-B Infineon HYB25D256800BT-5B
256MB Transcend TS32MLD64V4F3 Samsung K4H560838D-TCC4
512MB Transcend TS64MLD64V4F3 Samsung K4H560838D-TCC4
256MB Winbond W9425GCDB-5 Winbond W942508CH-5
512MB Winbond W9451GCDB-5 Winbond W942508CH-5
256MB A DATA MDOAD5F3G315B1ECZ Samsung K4H560838D-TCC4
256MB TwinMOS MDSTTUF08108L294K4FW0/T TwinMOS TMD7608F8E50B
512MB Hynix HYMD264646B8J-D43 AA Hynix HY5DU56822BT-D43
512MB Apacer 77.10636.465 Samsung K4H560838D-TCC4
-
2 -102 -102 -102 -102 -10
-
2 -112 -112 -112 -112 -11
P4P8T ®
P4P8T Accelerated Graphics Port (AGP)
Keyed for 1.5v
-
2 -122 -122 -122 -122 -12
23
5
6
-
2 -132 -132 -132 -132 -13
-
2 -142 -142 -142 -142 -14
-
2 -152 -152 -152 -152 -15
5
67
-
2 -162 -162 -162 -162 -16
3
4
5
6
-
2 -172 -172 -172 -172 -17
-
2 -182 -182 -182 -182 -18
c
d
b
a
d
-
2 -192 -192 -192 -192 -19
-
2 -202 -202 -202 -202 -20
-
2 -212 -212 -212 -212 -21
-
2 -222 -222 -222 -222 -22
-
3 - 23 - 23 - 23 - 23 - 2
CHA_FAN
FLO
PP
Y
CD1
AD1888
AUX1
USB56
P4P8T ®PCI Slot 1
Su
pe
r
I/O
FlashBIOS
PS/2T:MouseB:Keyboard
SE
C_I
DE
ATX12V
PAR
AL
LE
L P
OR
T
VGA1
MicIn
LineIn
LineOut
BUZZER
Socket 478
CLRTC
PR
I_ID
E
CPU_FAN
24.89cm (9.8in)
20.0
6cm
(7.
9in)
DD
R D
IMM
_A1
(64/
72-b
it, 1
84-p
in m
odul
e)
DD
R D
IMM
_B1
(64/
72-b
it, 1
84-p
in m
odul
e)
AGP
USB2.0T: USB3B: USB4
Top:RJ-45
SB_PWRPANEL
FP_AUDIO
SPDIF OUT
MDC
IntelICH5
Intel865G
CR2032 3VLithium Cell
CMOS Power
USB78
ATX
Pow
er C
onne
ctor
SATA2
SATA1
USB2.0T: USB1B: USB2
J1
LCD
_PA
NE
L
RT
L810
0C
-
3 - 33 - 33 - 33 - 33 - 3
P4P8T ®
P4P8T Clear RTC RAM
CLRTC
Normal Clear CMOS(Default)
1 2 2 3
-
3 - 43 - 43 - 43 - 43 - 4
P4P8T ®
P4P8T USB connector
US
B P
ower
US
BP
2–U
SB
P2+
GN
D+
5VP
ower
Bot
ton
US
B P
ower
US
BP
3–U
SB
P3+
GN
D
Dum
my
1
USB78
P4P8T ®
P4P8T USB connector
USB56U
SB
Pow
erU
SB
P2–
US
BP
2+G
ND
NC
US
B P
ower
US
BP
3–U
SB
P3+
GN
D
1 5
6 10
-
3 - 53 - 53 - 53 - 53 - 5
P4P8T ®
P4P8T Digital audio connector
+5V
SP
DIF
OU
TG
ND
SPDIF OUT
P4P8T ®
P4P8T Front panel audio connector
FP_AUDIO
BLI
NE
_OU
T_L
MIC
2
Line
out
_R
Line
out
_L
BLI
NE
_OU
T_R
NC
MIC
PW
R+
5VA
AG
ND
-
3 - 63 - 63 - 63 - 63 - 6
P4P8T ®
P4P8T Fan connectors
CPU_FANGND
Rotation+12V
CHA_FANGND
Rotation+12V
-
3 - 73 - 73 - 73 - 73 - 7
P4P8T ®
P4P8T ATX power connector
+3.3Volts-12.0VoltsGroundPower Supply OnGroundGroundGround-5.0 Volts+5.0 Volts+5.0 Volts
Power Good
+12.0Volts
+3.3 Volts+3.3 Volts
Ground+5.0 Volts
Ground+5.0 Volts
Ground
+5V Standby
ATX12V
ATXPWR
+12V DC
Ground+12V DC
Ground
-
3 - 83 - 83 - 83 - 83 - 8
•
•
P4P8T ®
P4P8T IDE connectors
NOTE: Orient the red markings(usually zigzag) on the IDEribbon cable to PIN 1.
SE
C_I
DE
PIN 1
PR
I_ID
E
P4P8T ®
P4P8T Internal audio connectors
AUX1 (White) CD1 (Black)
Rig
ht A
udio
Cha
nnel
Left
Aud
io C
hann
elG
roun
d
Rig
ht A
udio
Cha
nnel
Left
Aud
io C
hann
elG
roun
d
-
3 - 93 - 93 - 93 - 93 - 9
®
®
®
®
®
®
®
P4P8T ®
P4P8T SATA connectors
SATA2
GN
DR
SAT
A_T
XP
2R
SAT
A_T
XN
2G
ND
RS
ATA
_RX
P2
RS
ATA
_RX
N2
GN
D
SATA1
GN
DR
SAT
A_T
XP
1R
SAT
A_T
XN
1G
ND
RS
ATA
_RX
P1
RS
ATA
_RX
N1
GN
D
-
3 -103 -103 -103 -103 -10
®®®®® ®®®®®
P4P8T ®
P4P8T J1 connector
ODJ VOLUP ODJ STOP#ODJ VOLDN RAUSE
ODJ SCANRW ODJ PLAYODJ SCANFW GND
PB
J1
P4P8T ®
P4P8T LCD_PANEL connector
LCD_PANEL
PIC_CLK
+5VSB GNDPIC_STB# PIC_DOUTPIC_CLK PIC_DIN
PIC_DINPIC_STB# PIC_DOUTDJ_PLAY +5V
DJ_SCANFW DJ_SCANRWSMBDATA +5VSB
SMBCLK GND+12V
DJ_VOLUP DJ_VOLDNDJ_STOP#
-
3 -113 -113 -113 -113 -11
P4P8T ®
P4P8T System panel connector* Requires an ATX power supply.
PLE
D+
Gro
und
Power LED
PW
R
ATX PowerSwitch*
PLE
D-
IDE
_LE
D+
IDE
_LE
D-
IDE_LED
PANEL
-
3 -123 -123 -123 -123 -12
-
1
-
4 - 24 - 24 - 24 - 24 - 2
®
®
-
4 - 34 - 34 - 34 - 34 - 3
A:\>afudos /oMYBIOS03.rom
AMI Firmware Update Utility - Version 1.10
Copyright (C) 2002 American Megatrends, Inc. All rightsreserved.
Reading flash ..... 0x0008CC00 (9%)
A:\>afudos /oMYBIOS03.rom
AMI Firmware Update Utility - Version 1.10
Copyright (C) 2002 American Megatrends, Inc. All rightsreserved.
Reading flash ..... done
A:\>
-
4 - 44 - 44 - 44 - 44 - 4
A:\>afudos /ip4p8t.rom
AMI Firmware Update Utility - Version 1.10
Copyright (C) 2002 American Megatrends, Inc. All rightsreserved.
Reading file ..... done
Erasing flash .... done
Writing flash .... 0x0008CC00 (9%)
-
4 - 54 - 54 - 54 - 54 - 5
A:\>afudos /ip4p8t.rom
AMI Firmware Update Utility - Version 1.10
Copyright (C) 2002 American Megatrends, Inc. All rightsreserved.
Reading file ..... done
Erasing flash .... done
Writing flash .... 0x0008CC00 (9%)
Verifying flash .. done
A:\>
-
4 - 64 - 64 - 64 - 64 - 6
User recovery requested. Starting BIOS recovery...
Checking for floppy...
Floppy found!
Reading file ìp4p8t.romî. Completed.
Start flashing...
Flashed successfully. Rebooting.
User recovery requested. Starting BIOS recovery...
Checking for floppy...
-
4 - 74 - 74 - 74 - 74 - 7
Bad BIOS checksum. Starting BIOS recovery...
Checking for floppy...
Bad BIOS checksum. Starting BIOS recovery...
Checking for floppy...
Floppy found!
Reading file ìp4p8t.romî. Completed.
Start flashing...
-
4 - 84 - 84 - 84 - 84 - 8
Bad BIOS checksum. Starting BIOS recovery...
Checking for floppy...
Bad BIOS checksum. Starting BIOS recovery...
Checking for floppy...
Floppy not found!
Checking for CD-ROM...
CD-ROM found.
Reading file ìp4p8t.romî. Completed.
Start flashing...
-
4 - 94 - 94 - 94 - 94 - 9
®
-
4 -104 -104 -104 -104 -10
-
4 -114 -114 -114 -114 -11
-
4 -124 -124 -124 -124 -12
System Time [11:10:19]System Date [Tue, 06/29/2004]Language [English]
Primary IDE Master [Maxtor 6Y080L0]Primary IDE Slave [ASUS CDS520/]Secondary IDE Master [Not Detected]Secondary IDE Slave [Not Detected]Third IDE Master [Not Detected]Fourth IDE Master [Not Detected]IDE Configuration
System Information
Use [ENTER], [TAB] or[SHIFT-TAB] to select afield.
Use [+] or [-] toconfigure system time.
-
4 -134 -134 -134 -134 -13
System Time [11:10:19]System Date [Tue, 06/29/2004]Language [English]
Primary IDE Master [Maxtor 6Y080L0]Primary IDE Slave [ASUS CDS520/]Secondary IDE Master [Not Detected]Secondary IDE Slave [Not Detected]Third IDE Master [Not Detected]Fourth IDE Master [Not Detected]IDE Configuration
System Information
Use [ENTER], [TAB]or [SHIFT-TAB] toselect a field.
Use [+] or [-] toconfigure systemtime.
-
4 -144 -144 -144 -144 -14
System Time [11:10:19]System Date [Tue, 06/29/2004]Language [English]
Primary IDE Master [Maxtor 6Y080L0]Primary IDE Slave [ASUS CDS520/]Secondary IDE Master [Not Detected]Secondary IDE Slave [Not Detected]Third IDE Master [Not Detected]Fourth IDE Master [Not Detected]IDE Configuration
System Information
Use [ENTER], [TAB] or[SHIFT-TAB] to select afield.
Use [+] or [-] toconfigure system time.
-
4 -154 -154 -154 -154 -15
Primary IDE Master Select the type ofdevice connected to thesystem.Device : Hard Disk
Vendor : Maxtor 6Y080L0Size : 81.9GBLBA Mode : SupportedBlock Mode : 16 SectorsPIO Mode : 4Async DMA : MultiWord DMA-2Ultra DMA : Ultra DMA-6SMART Monitoring: Supported
Type [Auto]LBA/Large Mode [Auto]Block (Multi-sector Transfer) M [Auto]PIO Mode [Auto]DMA Mode [Auto]Smart Monitoring [Auto]32Bit Data Transfer [Auto]
-
4 -164 -164 -164 -164 -16
®
®
IDE Configuration
Onboard IDE Operate Mode [Enhanced Mode] Enhanced Mode Support On [S-ATA] IDE Detect Time Out (Sec) [35]
Set [Compatible Mode]when Legacy OS (i.e.WIN ME, 98, NT4.0, MSDOS) is used.
Set [Enhanced Mode]when Native OS (i.e.WIN2000, WIN XP) isused.
-
4 -174 -174 -174 -174 -17
AMI BIOSVersion : 08.00.09Build Date : 06/15/04ID : A0103101
ProcessorType : Intel(R) Celeron(R) CPU 1.70GHzSpeed : 1700MHzCount : 1
System MemorySize : 120MB
-
4 -184 -184 -184 -184 -18
CPU ConfigurationChipsetOnboard Devices ConfigurationPCI PnPUSB Configuration
Load MiniLoader [Disabled]
Configure CPU.
Configure advanced CPU settings Sets the rationbetween CPU Core Clockand the FSB Freuency.
Note: If an invalidratio is set in CMOS,then actual andsetpoint values maydiffer.
Manufacturer : Intel(R)Brand String : Intel(R) Celeron(R) 4 CPU 1.70GHzFrequency : 1700MHzFSB Speed : 400MHz
Cache L1 : 8 KBCache L2 : 128 KBCache L3 : 0 KB
Ratio Status : LockedRatio Actual Value : 17Max CPUID Value Limit [Disabled]
-
4 -194 -194 -194 -194 -19
Set DDR referencevoltage.
WARNING: Setting wrong values in the sections below may cause system to malfunction.
DDR Reference Voltage [Auto]DRAM Frequency [Auto]Configure DRAM Timing by SPD [Enabled]Internal Graphic Accelerate Mode [Auto]
Graphic Adapter Priority [AGP/Int-VGA]Onboard Video Memory [Enabled, 8MB]Graphics Aperture Size [ 64MB]
Boot Display Device [Auto]Flat Panel type [640x480LVDS]TV Standard [Auto]MPS Revision [1.4]
Advanced Chipset settings
-
4 -204 -204 -204 -204 -20
-
4 -214 -214 -214 -214 -21
’
OnBoard AC’97 Audio� [Auto]OnBoard LAN [Enabled] OnBoard LAN Boot ROM [Disabled]
Parallel Port Address [378]Parallel Port Mode [EPP+ECP] EPP Version [1.9] ECP Mode DMA Channel [DMA3] Parallel Port IRQ [IRQ7]
-
4 -224 -224 -224 -224 -22
-
4 -234 -234 -234 -234 -23
NO: Lets the BIOSconfigure all thedevices in the system.YES: Lets theoperating systemconfigure Plug andPlay (PnP) devices notrequired for boot ifyour system has a Plugand Play operatingsystem.
WARNING: Setting wrong values in the sections below may cause system to malfunction.
Plug and Play OS [No]PCI Latency Timer [64]Allocate IRQ to PCI VGA [Yes]Palette Snooping [Disabled]PCI IDE BusMaster [Enabled]
IRQ3 [Available]IRQ4 [Available]IRQ5 [Available]IRQ7 [Available]IRQ9 [Available]IRQ10 [Available]IRQ11 [Available]IRQ14 [Available]IRQ15 [Available]
Advanced PCI PnP settings
-
4 -244 -244 -244 -244 -24
Enables USB hostcontrollers.
Module Version : 2.22.4-5.3
USB Devices Enabled : None
USB Function [8 USB Ports]Legacy USB Support [Auto]USB 2.0 Controller [Enabled]USB 2.0 Controller Mode [FullSpeed]
USB Mass Storage Device Configuration
USB Configuration
-
4 -254 -254 -254 -254 -25
Number of secondsPOST waits for the USBmass storage deviceafter start unitcommand.
USB Mass Storage Reset Delay [20 Sec]
No USB Mass Storage device detected
Device #1 N/A Emulation Type [N/A] Device #2 N/A Emulation Type [N/A] Device #3 N/A Emulation Type [N/A] Device #4 N/A Emulation Type [N/A] Device #5 N/A Emulation Type [N/A] Device #6 N/A Emulation Type [N/A]
USB Mass Storage Device Configuration
-
4 -264 -264 -264 -264 -26
Suspend Mode [Auto]Repost Video on S3 Resume [No]ACPI 2.0 Support [No]ACPI ASIC Support [Enabled]
APM ConfigurationHardware Monitor
Select the ACPI stateused for SystemSuspend.
-
4 -274 -274 -274 -274 -27
APM Configuration
Restore on AC Power Loss [Power Off]
Power On By PS/2 Devices [Disabled]Power On By External Modems [Disabled]Power On By PCI Devices [Disabled]Power On By RTC Alarm [Disabled]
Set power stateafter AC powerfailure.
-
4 -284 -284 -284 -284 -28
º ºº º
MB temperature.
MB Temperature [36°C/96.5°F]CPU Temperature [44°C/111°F]
CPU Fan Speed [5234RPM]Chassis Fan Speed [N/A]
VCORE Voltage [1.808V]3.3V Voltage [3.376V]5V Voltage [5.080V]12V Voltage [11.977V]
SMART Q-Fan Function [Enabled]
Hardware Monitor
-
4 -294 -294 -294 -294 -29
Boot Settings
Boot Device PriorityRemovable Drives
Boot Settings ConfigurationSecurity
Specifies the BootDevice Prioritysequence.
Boot Device Priority
1st Boot Device [PM-Maxtor 6Y080L0]2nd Boot Device [1st Floppy Drive]
Specifies the bootsequence from theavailable devices.
A device enclosed inparenthesis has beendisabled in thecorresponding typemenu.
-
4 -304 -304 -304 -304 -30
Removable Drives
1st Drive [1st Floppy Drive]
Specifies the bootsequence from theavailable devices.
Boot Settings Configuration
Quick Boot [Enabled]Full Screen Logo [Enabled]Add On ROM Display Mode [Force BIOS]Bootup Num-Lock [On]PS/2 Mouse Support [Auto]Typematic Rate [Fast]Boot to OS/2 [No]Wait for ‘F1’ If Error [Enabled]Hit ‘DEL’ Message Display [Enabled]Interrupt 19 Capture [Disabled]
Allows BIOS to skipcertain tests whilebooting. This willdecrease the timeneeded to boot thesystem.
-
4 -314 -314 -314 -314 -31
‘ ’
‘ ’
-
4 -324 -324 -324 -324 -32
Security Settings
Supervisor Password Not InstalledUser Password Not Installed
Change Supervisor Password
Boot Sector Virus Protection [Disabled]
to changepassword. again todisable password.
-
4 -334 -334 -334 -334 -33
Security Settings
Supervisor Password Not InstalledUser Password Not Installed
Change Supervisor PasswordUser Access Level [Full Access]Change User PasswordClear User PasswordPassword Check [Setup]
Boot Sector Virus Protection [Disabled]
to changepassword. again todisable password.
-
4 -344 -344 -344 -344 -34
Exit Options
Exit & Save ChangesExit & Discard ChangesDiscard Changes
Load Setup Defaults
Exit system setupafter saving thechanges.
F10 key can be usedfor this operation.
-
4 -354 -354 -354 -354 -35
-
4 -364 -364 -364 -364 -36
-
5 - 25 - 25 - 25 - 25 - 2
®
-
5 - 35 - 35 - 35 - 35 - 3
-
5 - 45 - 45 - 45 - 45 - 4
®
®
®
®
®
-
5 - 55 - 55 - 55 - 55 - 5
®
® ®
® ® ®
-
5 - 65 - 65 - 65 - 65 - 6
-
5 - 75 - 75 - 75 - 75 - 7
-
5 - 85 - 85 - 85 - 85 - 8
-
5 - 95 - 95 - 95 - 95 - 9
-
5 -105 -105 -105 -105 -10
-
5 -115 -115 -115 -115 -11
-
5 -125 -125 -125 -125 -12
-
5 -135 -135 -135 -135 -13
-
5 -145 -145 -145 -145 -14
-
5 -155 -155 -155 -155 -15
-
5 -165 -165 -165 -165 -16
®