rtd module - cimon.com€¦ · 04-07-2014 · cicon, the rtd input type of each channel and the...

RTD ModuleCM1-RD04ACM1-RD04B

www.cimon.com

MEMO

CautionTo use this product safely please read the following

instructions

The power must be off whenever you are in contact with the product.

Read and understand the following technical information about the product.

For your safety only a qualified electrician should work on this product.

1.

2.

3.

Available RTD

Range of Temperature Input

Digital Output

Detecting the breaking of wires

Accuracy

Max.Conversion Rate

Number of Temperature Inputs

Insulation

Contact terminal

No. of Occupied Points

Pt100(JIS C1640-1989, DIN 43760-1980)JPt100(KS C1603-1991, JIS C 1604-1981)

Pt100:-200.0°C to 600°C(18.48 to 313.59Ω)

JPt100:-200.0°C to 600°C(17.14 to 317.28Ω)

Pt1000 (DIN EN 60751)

Pt1000:-200.0°C to 600°C(185.20 to 3137.08Ω)

Ni1000(DIN 43760): -50°C to 160°C(742.6 to 1986.3Ω)

Ni1000(TCR 5000): -50°C to 160°C(790.0 to 1799.3Ω)

50ms / 1ch.

4 Ch. / 1 module

Between input terminal and PLC Power : Photo-CouplerBetween channels : No

18-points Terminal Block

16 Points

InternalCurrent

(mA)

50

30

10

+5V

+15V

-15V

3 wires per channel

Digital converted value : 0~16,000(-8000~8000)Detected temperature value: -2000~6000

(First decimal place value X 10 times)

±0.1%[Full Scale]

CM1-RD04A CM1-RD04B

General Specifications Module Specifications

Items Specification Standards

Ambient Temp. -10°C~70°C -Storage Temp. -25°C~80°C -

Ambient Humidity 5~95%RH, (Non-condensing) -Storage Humidity 5~95%RH, (Non-condensing) -

Vibration

For discontinuous vibration

IEC 61131-2

Frequency Acceleration Amplitude Times

10≤f<57Hz - 0.075mm

X,Y,ZEach direction,

10 times

57≤f≤150Hz 9.8m/s2{1G} -

Contionuous vibrationFrequency Acceleration Amplitude

10≤f<57Hz - 0.035mm

57≤f≤150Hz 4.9m/s2{1G} -

Shocks · Max. impact acceleration: 147m/S2(15G) · Authorized time : 11ms · Pulse wave : Sign half-wave pulse (3 times each in X, Y, Z)

IEC 61131-2

Noise

Square waveimpulse noise ± 2,000V CIMON

standard

Electrostaticdischarge Voltage : 4kV (contact discharging) IEC 61131-2

IEC 1000-2Radiated

electromagneticfield noise

27~500 MHz,10V/m IEC 61131-2IEC 1000-4-3

Fast TransientBurst noise

Powermodule

Digital I/O(24V or more)

Digital I/O(less than 24V)Analog I/O

Comm. interface IEC 61131-2IEC 1000-4-4

2 kV 2 kV 0.25 kV

Voltage 2 kV/1min 0.5 kV/1min

Ambientconditions No corrosive gas or dust

Cooling type Natural air cooling

※ 4, 8, 12, 16, 17 terminals are not used.1) The temperature converted by a platinum resistance temperature detector of Pt100 of Jpt100 or Pt1000 or Ni1000 can be displayed in ℃ or ℉, and the temperature values can be processed as digital values up to the first decimal place.

2) The converted temperature data are converted to 16bit binary data, which can be processed as digital values. The temperature in the range from -200℃ to 600℃ are converted to the values from 0 to 16000(-8000~8000).

3) The range of temperature is from -250℃ to 650℃, and the range of digital value is from -192 to 16191.

4) If Min and Max. temperature values are set up, the min. value will ve converted to 0 (-8000) and the max. value is 16000(8000).

5) Each channel can detect the breaking of resistance temperature, cables, and the excess of measuring range.

6) There are 4 channels to connect PT100, JPT100, PT1000 or Ni1000.

7) The number of modules used on one base is not limited.

8) LED is lighted in normal status, and blinks at the intervals of 0.2 second in error status.

Features and Operation of CM1-RD04A, RD04B Front view(RTD)

Terminals are grouped as 1-2-3, 5-6-7, 9-10-11,13-14-15, and each above channel takes input.

1) Pt100 or JPt100 has 100Ω(resistance) at 0℃, and the Resistance value changes according to temperature variation.

2) CM1-RTD gets resistance values by dividing voltage, and converts Resistance to a temperature value to save the result in memory.

3) RTD input module linearizes the resistance input of non-linear RTD as follows.

Wiring MethodTerminal Block Terminal Block or Input Module

Ch 1

Ch 2

Ch 3

Ch 4

CH Terminal A Terminal B Terminal b Terminal FG

Terminal 1

Terminal 5

Terminal 9

Terminal 13

Terminal 3

Terminal 7

Terminal 11

Terminal 15

Terminal 2

Terminal 6

Terminal 10

Terminal 14

Terminal 18

Terminal 18

Terminal 18

Terminal 18

↑Converted

Temperaturevalue

※ Connect both shields of RTD and wire to FG of RTD input module. The difference between wires must be 1Ω or less.

Characteristic of Linear Temperature-Resistance

Characteristic of Actual Temperature-Resistance

Resistance ValueTemperature-detected

Wiring Characteristics of RTD Conversion

User Program Memory User Program Memory

Hexa0H1H2H3H4H5H6H7H8H9HAHBHCHDHEHFH10H11H12H13H

14H

15H16H17H18H19H1AH1BH1CH1DH

Hexa1EH1FH20H21H22H23H24H25H26H27H28H29H2AH2BH2CH2DH2EH2FH30H31H32H33H34H35H36H37H38H39H3AH3BH3FH

Deci012345678910111213141516171819

20

212223242526272829

Deci3031323334353637383940414243444546474849505152535455565758

59~6263

R/WRRRRRRRR

R/WR/W

RRRRRRRRR

R/W

RRRRRRRR

R/W

R/WRRRRRRRR

-

R/WR/WR/WR/WR/WR/WR/WR/WR/W

RR/WR/WR/WR/WR/WR/WR/WR/WR/W

R

Enabling/Disabling RTD conversionDetected temp. value of CH.1(℃)

Detected temp. value of CH.2(℃)







Assigning RTD typeSet Digital Output 1

Detected temp. value of CH.1(℉)








Information on operating channels

Assigning RTD

(RD04B ver1.18 or more)

Digitally converted value of CH.1Digitally converted value of CH.2Digitally converted value of CH.3Digitally converted value of CH.4Digitally converted value of CH.5Digitally converted value of CH.6Digitally converted value of CH.7Digitally converted value of CH.8

Set Digital Output 2

Assigning Average ProcessError code value of CH.1Error code value of CH.2Error code value of CH.3Error code value of CH.4Error code value of CH.5Error code value of CH.6Error code value of CH.7Error code value of CH.8

Not use

Max. temp. input value of CH.1Max. temp. input value of CH.2Max. temp. input value of CH.3Max. temp. input value of CH.4Max. temp. input value of CH.5Max. temp. input value of CH.6Max. temp. input value of CH.7Max. temp. input value of CH.8

Max./Min. temp. set dataError in max./min. setting

Min. temp. input value of CH.1








Setting up average Time/Filter coefficient for CH1~CH4OS version

Address AddressDescription DescriptionR/W R/W

I/O Signal Error Code

Input

X0

X1

X2

X3

X4

X5

X6

X7

X8

X9

XA

XB

XC

XD

XE

XF

Output

Y0

Y1

Y2

Y3

Y4

Y5

Y6

Y7

Y8

Y9

YA

YB

YC

YD

YE

YF

Signal Name

RTD module ready

Flag (RTD conversion completed)

Flag (Set Value saving is completed)

Signal Name

Requesting to save the Set Value(SV)

Not Used Not Used

Flag(error occurred in RTD module)

Requesting to clearan error

Signal Direction(CPU ← RTD)

Signal Direction(CPU → RTD)

In case that RTD or cable is broken down, or measured temperature values are greater than maximum value or less than minimum value, the following error codes are stored in Buffer Memory from "31" to "38" for each channel and LED blinks at the intervals of 0.3 sec.

In order to clear error code, open CICON and click [Online] → [RTD Module] → [Status] and then click [Reset Error].

∆ is 0~3 for RTD modules.

If error occurs in maximunm and minimum temperature setting, the bit for Buffer Memory "50" becomes 1, and LED blinks at the intervals of 0.3 sec.

Not Used

Error Code Description01 When A is disconnected

02 When B is disconnected

03 When b or both A and B is disconnected

04 When a measured temperature go out of max. and min. temperature

10∆ System error (A/S required)

Trouble Shooting(1) Trouble Shooting(2)

RTD input values do not match to the detected temperature values. CPU module cannot read the converted temperature values.

When values are uploaded from the Special Card Setup of the CICON, the RTD input type of each channel and the connected input type are correct?

Power module type is CM1-SPC.

The channel is assigned correctly when uploading in Special Card Setup of CICON.

Modify the channel configuration to be used.

The wiring of channel input terminal is correct.

Wire correctly.

RTD Hardware is broken down.

Replace the power module with SPC.

Check out the current Input type, and modify it correctly in CICON.Y

YN

N

YY

Y

NN

NN

Wire correctly.

Ground FG terminal.

The wiring of RTD module input terminal is correct?

FG Terminal is grounded?

RTD hardware is broken down.

Outward Dimension

Unit(mm)

Revision History

Version Date Content Page

V1.0 2013-10-08 New Revision -

January 2014All Cimon products including hardware, software, and firmware (collectively called “Products”) carry a one-year warranty against defects in materials and workmanship beginning from the date of product receipt from seller or its appointed distributor. If a product proves defective in materials and workmanship within one year from the date of purchase, we will replace or repair it. Products returned under warranty after 30 days may be replaced with refurbished or remanufactured goods at Cimon’s discretion. Cimon makes no representation or warranty, express or implied, that the operation of the Products will be uninterrupted or error free, or that the functions contained therein will meet or satisfy buyer’s intended use or requirements. Repaired or replaced Products provided as a result of this warranty are warranted for a period of six (6) months from the shipment to buyer or the remainder of the original warranty term for that particular product, whichever is longer. Cimon’s standard policy is that all customers are responsible for freight charges to Cimon when returning products under the warranty return policy.

This warranty will be void if Products date codes or serial numbers are removed or defaced. Warranties do not apply to products that have been subjected to abnormal use, abnormal conditions, improper storage, exposure to moisture or dampness, unauthorized modifications, unauthorized repair, misuse, neglect, accident, alteration, improper installation or other acts which are not the fault of Cimon, including damage caused in shipping. Our warranty also does not apply to any product that has been damaged by external causes such as fire, flood, sand, dirt, lightning, acts of God, battery leakage, theft, blown fuses, improper use of any electrical source or connection to product not recommended in writing for interconnection by Cimon.

In no event will Cimon be liable, whether in contract, tort or under any other legal theory, for lost profits or revenues, loss of use or similar economic loss, for any indirect, special, incidental, consequential, punitive or similar damages arising out of or in connection with any products including non-conforming products, or for any third party claims against you relating to the products, even if we have been advised of the possibility of such claim. In no event will our monetary liability in respect of any product exceed the purchase price that you paid for it.

1)

2)

3)

4)

5)

6)

Product WarrantySafety Instruction

Use a cable for input signal of module differently from a cable for AC to prevent the influence of surge or induction noise occurring from AC.

Select a cable considering ambient temperature and allowable current AWG22(0.3mm2) or more is recommended.

If the wiring is to colse to heat-generating device or directly contacted with oil for long periods of time it may cause short circuit, breakdown or malfunction.

In case of wiring together with high-voltage cable or power line, it may cause malfunction or breakdown.

The tightening torque is 6.99 in.Ib.

Use copper or copper-clad aluminum conductor.

CIMON LTD AND ITS AFFILIATES AND SUPPLIERS DISCLAIM ANY REP-RESENTATIONS OR WARRANTIES THAT YOUR USE OF THE PRODUCTS WILL SATISFY OR ENSURE COMPLIANCE WITH ANY LEGAL OBLIGATIONS OR LAWS OR REGULATIONS.

LIMITATION OF LIABILITY AND INDEMNITY. TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THE ENTIRE LIABILITY OF CIMON, AND ITS AFFILIATES AND SUPPLIERS FOR ALL MATTERS OR CLAIMS RELATING TO THIS AGREEMENT SHALL BE LIMITED TO THE AMOUNT YOU PAID FOR THE PRODUCTS DURING THE

TWELVE (12) MONTHS PRIOR TO SUCH CLAIM.

THE STATUTE OF LIMITATIONS FOR FILING A CLAIM SHALL BE LIMITED TO THE SHORTER OF TWELVE MONTHS, OR THE SHORTEST PERIOD ALLOWED UNDER APPLICABLE LAW.

SUBJECT TO APPLICABLE LAW, CIMON AND ITS AFFILIATES AND SUPPLIERS ARE NOT LIABLE FOR ANY OF THE FOLLOWING: (A) INDIRECT, SPECIAL, INCIDENTAL, PUNITIVE OR CONSEQUENTIAL DAMAGES; (B) DAMAGES RELATING TO FAILURES OF TELECOMMUNICATIONS, THE INTERNET, ELECTRONIC COMMUNICATIONS, CORRUPTION, SECURITY, LOSS OR THEFT OF DATA, VIRUSES, SPYWARE, LOSS OF BUSINESS, REVENUE, PROFITS OR INVESTMENT, OR USE OF SOFTWARE OR HARDWARE THAT DOES NOT MEET CIMON SYSTEM REQUIREMENTS. THE ABOVE LIMITATIONS APPLY EVEN IF CIMON AND ITS AFFILIATES AND SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES AND/OR THE POSSIBILITY OF DAMAGES GREATER THAN THE LIMITATION ABOVE. THIS AGREEMENT SETS FORTH THE ENTIRE LIABILITY OF CIMON, ITS AFFILIATES AND YOUR EXCLUSIVE REMEDY WITH RESPECT TO THE SOFTWARE AND ITS USE.

THE PARTIES FURTHER AGREE THAT THE APPLICABLE LAW AND VENUE FOR ANY DISPUTED ARE THE LAWS OF CALIFORNIA. TO THE EXTENT ALLOWED BY APPLICABLE LAW, ANY CLAIMS SHALL BE BROUGHT IN LOS ANGELES CALIFORNIA AND CALIFORNIA LAW SHALL APPLY. THE CALIFORNIA VERSION OF THE UCC IS THE PREFERRED LAW TO BE APPLIED TO ANY WARRANT AND RELATED CLAIMS.

Product Warranty

To minimize the risk of potential safety problems, you should follow all applicable local and national codes that regulate the installation and operation of your equipment. These codes vary from area to are and usually change with time. It is your responsibility to determine which codes should be followed, and to verify that the equipment, installation and operation is in compliance with the latest revision of these codes.

CIMON SOFTWARE AND HARDWARE (COLLECTIVELY REFFERED TO AS, “PRODUCTS”) LICENSE DISCLAIMER AND LIMITATION OF WARRANTIES

YOUR USE OF ANY CIMON PRODUCTS AND CONTENT ACCESSIBLE THROUGH THE PRODUCTS IS ENTIRELY AT YOUR OWN RISK. EXCEPT AS DESCRIBED IN THIS AGREEMENT, THE PRODUCTS ARE PROVIDED "AS IS." TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, CIMON, ITS AFFILIATES, AND ITS THIRD PARTY SERVICE OR DATA PROVIDERS, LICENSORS, DISTRIBUTORS OR SUPPLIERS (COLLECTIVELY REFERRED TO AS, "SUPPLIERS") DISCLAIM ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY WARRANTY THAT THE PRODUCTS ARE FIT FOR A PARTICULAR PURPOSE, TITLE, MERCHANTABILITY, DATA LOSS, NON-INTERFERENCE WITH OR NON-INFRINGEMENT OF ANY INTELLECTUAL PROPERTY RIGHTS, OR THE ACCURACY, RELIABILITY, QUALITY OR CONTENT IN OR LINKED TO THE PRODUCTS.

CIMON AND ITS AFFILIATES AND SUPPLIERS DO NOT WARRANT THAT THE PRODUCTS ARE SECURE, FREE FROM BUGS, VIRUSES, INTERRUPTION, ERRORS, THEFT OR DESTRUCTION. FURTHER, CIMON DOES NOT WARRANT ACCESS TO THE INTERNET OR TO ANY OTHER SERVICE, CONTENT OR DATA TRANSMITTED THROUGH THE PRODUCTS. IF THE EXCLUSIONS FOR IMPLIED WARRANTIES DO NOT APPLY TO YOU, ANY IMPLIED WARRANTIES ARE LIMITED TO 60 DAYS FROM THE DATE OF PURCHASE OR DELIVERY OF THE PRODUCTS, WHICHEVER IS SOONER.

EQUIPMENT DAMAGE OR SERIOUS INJURY TO PERSONNEL INCLUDING DEATH CAN RESULT FROM THE FAILURE TO FOLLOW ALL APPLICABLE CODES AND STANDARDS INCLUDING ENGINEERING STANDARDS. CIMON DOES NOT ASSUME ANY RESPONSIBILITY FOR YOUR PRODUCT DESIGN, INSTALLATION OR OPERATION.

Product Warranty

MEMO MEMO

Version:1.0

Revision Date : Oct, 2013

Printed : Jul, 2014

BCP13029

H.Q Address : 5F KDT B/D, #48, Beolmal-ro, Bundang-gu,Seongnam-si, GyeongGi-do, Korea 463-836Tel : +82-31-778-3071Homepage : www.cimon.com

CIMON CO.,LTD.

USA : 3699 Wilshire Blvd suite 1250 Los Angeles CA90010Tel : 213 384-8703Homepage : www.cimon.com

rtd module - cimon.com€¦ · 04-07-2014 · cicon, the rtd input type of each channel and the...

Documents