robotc for vex cortex llano estacado roboraiders frc team 1817
DESCRIPTION
ROBOTC for VEX Cortex Llano Estacado RoboRaiders FRC Team 1817. Humans and Machines. Machines are built to perform useful tasks. The way a Machine works depends entirely on the way the Human build it. - PowerPoint PPT PresentationTRANSCRIPT
06/2012 Tanya Mishra 1
ROBOTC for VEX CortexLlano Estacado RoboRaiders
FRC Team 1817
08/2012 Tanya Mishra 2
Humans and Machines Machines are built to perform useful tasks. The way a Machine works depends entirely on the way
the Human build it. Since Machines and Robots need a medium of
communication, a language called “Programming Language” is used.
EASYC, ROBOTC, C++, C all are programming languages.
The instructions in the language are called “Programs” and the human that writes the instructions is called the “Programmer”.
08/2012 Tanya Mishra 3
Task of Programmer: Understand Problem, Find a solution, Write a program to solve the problem in the required Programming language.
Task of Machine: Follow the program provided. A ROBOT is a Machine.
08/2012 Tanya Mishra 4
Planning and Behavior
Behavior: Action the Robot has to take. Big Behavior: Solving a maze Small Behavior: Turn Left, Move Forward, etc. Big Behavior is made up of Smaller Behaviors. Plan a Solution to the problem. Break down the plan into detailed smaller steps. Each step is a behavior the robot needs to follow. Sequence of these steps in English is called “pseudo-
code”.
08/2012 Tanya Mishra 5
08/2012 Tanya Mishra 6
“Flow charts” are a visual representation of the program flow.
Start and End: “Rounded Rectangles”. They contain the word “Start” or “End”, but can be more specific such as “Power Robot Off” or “Stop All Motors”.
Actions: “Rectangles”. They act as basic commands and process steps.
Decision blocks: “Diamonds”. These typically contain Yes/No questions. Based on the choice, the next step is determined.
08/2012 Tanya Mishra 7
08/2012 Tanya Mishra 8
Introduction to C Programming
EasyC is based on the the principles of C Programming.
We will cover the following concepts:
1. Basic Components of a C Program
2. Data Types and Variables
2. Conditional operators
3. Control Structures and Loops
4. Methods and Functions
08/2012 Tanya Mishra 9
A Basic C Program
#include<stdio.h> // Header File
void main(void) // Main function
{
// Body of the main function
}
Header file: Includes all the required words and instructions needed to write a program
Main function: Execution starts from here Body: stepwise Instructions to the Robot
08/2012 Tanya Mishra 10
Each Instruction to the robot is also called a “Statement”.
When the list of instruction is send to the VEX cortex, it read them from top to bottom and left to right.
Different Commands use different paired Punctuations such as “[]” “{}” “()”
“{..}” defines a body of one or more instructions. Also called a “Compound Statement”.
Every instruction in the body ends with a “;”. It shows the end of a instruction.
08/2012 Tanya Mishra 11
Comments are for the programmer to understand what a particular statement does.
Two kinds of comments:
1. // This is a one line comment
2. /* This is a more than one line
Comment.*/ C language is case sensitive: Upper and lower
cases are considered different.
08/2012 Tanya Mishra 12
Data types and Variables A “Variable” is a place to store a value. A variable has a “Type” and a “Name” “Type” deals with the type of Data the variable
will hold.
Type of Data:
Int: Whole Numbers. Positive, Negative, Zero
float(Floating Point): Decimal Point Numbers. Positive and Negative.
String: Text. Letters, Spaces and characters.
08/2012 Tanya Mishra 13
char(Characters): Single characters
bool(Boolean): True and False values
Declare a variable: int Age;
float Score;
string Name;
char Grade;
bool Pass;
08/2012 Tanya Mishra 14
Assign a variable: Age = 18;
Score = 90.5;
Name = “William”;
Grade = 'A';
Pass = True;
Declare and assign: int Age = 18;
float Score = 90.5;
string Name = “William”;
char Grade = 'A';
bool Pass = True;
08/2012 Tanya Mishra 15
Variable Naming Rules: A variable name can not have spaces in it. A variable name can not have symbols in it. A variable name can not start with a number. A variable name can not be the same as an
existing reserved word.
Scope of a Variable: Local variables: Within a certain block of code
or function. Cannot be accessed outside. Global variables: Can be accessed anywhere
in the code.
08/2012 Tanya Mishra 16
Using Variables in a print to screen function:
When printing a variable on the screen, the following syntax is used:
Print to screen function(“%type”,Variable);
Signed : + and - , unsigned: - , short: less range , long : more range
08/2012 Tanya Mishra 17
Conditional Operators Comparison operators
Relational Operator Example
> (Greater Than) 7 > 5
>= (Greater Than or Equal To) 7 >= 5 , 7 >= 7
< (Less Than) 5 < 7
<= (Less Than or Equal To) 5 < 7 , 7<=7
== (Equal To) 7 == 7
!= (Not Equal To) 7 != 5
= (Assignment Operator) number = 7
08/2012 Tanya Mishra 18
Logical operators:
Boolean Truth TableJoining two or more statements using “And” and “Or”
A: Its a Sunny Day
B: My Car is working
Can I go out?(A and B)
Can I go out?(A or B)
Yes Yes Yes Yes
Yes No No Yes
No Yes No Yes
No No No No
08/2012 Tanya Mishra 19
And : &&
Or : ||
Not : !
A B !A A && B A || B
True True False True True
True False False False True
False True True False True
False False True False False
08/2012 Tanya Mishra 20
Control Structures and LoopsControl Structure
IF statements:if(condition)
{
Instructions, if “condition” is True
}
08/2012 Tanya Mishra 21
IF-ELSE Statements:if(condition)
{
// Instructions, if “condition” is true
}
else
{
// Instructions, if “condition” is false
}
08/2012 Tanya Mishra 22
ELSE-IF Statements:if(condition1)
{
// Instructions, if “condition 1” is true
}
else if(condition 2)
{
// Instructions, if “condition 2” is true
}
else
{
// Instructions, if “condition 1” and “condition 2” are false
}
08/2012 Tanya Mishra 23
Switch Statements:switch(expression) //expression can only be an “int” or “char”
{
case Value-1:
// Instructions, if expression = Value-1
break;
case Value-2:
// Instructions, if expression = Value-2
break;
default:
// Instructions, if expression does not match any Value
}
08/2012 Tanya Mishra 24
Example:
char Grade = 'A';
switch(Grade)
{
case A:
Your Grade is A;
break;
case B:
Your Grade is B;
break;
default:
This is the default choice
}
08/2012 Tanya Mishra 25
Loops While loops:
while(condition)
{
// Instructions, if “condition” is true
}Note: Control Structures execute only once. On the other hand, while
loops execute continuously until the condition is false.
If the condition in the loop is always true, the loop never ends. Such a loop is called an “Infinite Loop”.
A loop will end only when the condition is false or there is a “break” statement.
08/2012 Tanya Mishra 26
Example:int count = 0; //Initialization
while(count <= 2) //Condition
{
PrintToScreen(“ I have %d apple \n”, count);
count = count + 1; //Increment
}
Output: I have 0 apple
I have 1 apple
I have 2 apple
08/2012 Tanya Mishra 27
For Loop:
for(initialization; condition; increment)
{
// Instructions, If “condition” is true
}
Similar to a while loop except that the initialization and increment are all together.
Note: Initialization is done only when the loop first starts. After that it is skipped.
08/2012 Tanya Mishra 28
Example:int count;
for(count =0; count <= 2; count = count +1)
{
PrintToScreen(“ I have %d apple \n”, count);
}
Output: I have 0 apple
I have 1 apple
I have 2 apple
Note: \n is called new lines. It prints the next sentence in a new line.
08/2012 Tanya Mishra 29
Methods and function
Functions are named sections of code that can be called from other sections of code.
Also called subroutines. Every executable statement in C must live in a
function. Functions have a Data type, name and input
values. Input values are called Parameters. They are
the values you want the function to work with.
08/2012 Tanya Mishra 30
The function definition specifies the “return value” and the “parameters” of the function:
<data type> FunctionName(<param1>, <param2>, ...)
{
<function body>
<return type>
}
Return type and Data type should be of the same kind.
Return type is “void” if nothing is to be returned.
Parameters is “void” if nothing is to be passed in.
08/2012 Tanya Mishra 31
Example:
int addition(int x, int y)
{
int z;
z = x+ y;
return z;
}
void main(void)
{
addition(2, 3);
}
08/2012 Tanya Mishra 32
Some Useful termsCompiler: Turns C program into the machine
language for the controller.
Loader: Loads the machine language output of the compiler (along with other stuff) into the robot controller.
Machine Language: What the robot controller actually understands. Found in .HEX files.
10110100
11100101
00001011
06/2012 Tanya Mishra 33
Download ROBOTC
Download Link: ROBOTC for CORTEX and PIC
www.robotc.net->Download->ROBOTC 3.0 for CORTEX and PIC
or
http://www.robotc.net/download/cortex/
06/2012 Tanya Mishra 34
ROBOTC Rulestask main()
{
motor[port3] = 127;
wait1Msec(3000);
}
Important words are highlighted. Uppercase and Lowercase matters. White spaces and tabs are for programmer convenience Sentences or Instructions are separated by semicolon. Instructions are read from T – B and L-R.
06/2012 Tanya Mishra 35
Error Messages
Compiler analyzes your programs to identify syntax errors, capitalization and spelling mistakes, and code inefficiency (such as unused variables).
Errors: Major issues. misspelled words, missing semicolons, and improper syntax. Errors are denoted with a Red X.
Warnings: Minor issues. These are usually incorrect capitalization or empty, infinite loops. Warnings are denoted with a Yellow X.
06/2012 Tanya Mishra 36
Information: ROBOTC will generate information messages when it thinks you have declared functions or variables that are not used in your program. These messages inform you about inefficient programming. Information messages are denoted with a “White X”.
06/2012 Tanya Mishra 37
System Configurations “Firmware” is a piece of software that accessing
the operating system in the processor enabling it to perform its task.
Update firmware to make sure it is compatible with the ROBOTC and latest Vex Hardware
Update Firmware on Cortex: Cortex Micro controller is the “Brain”
06/2012 Tanya Mishra 38
It has two separate processors inside:
1. User Processor : Handles all ROBOTC programming instructions.
2. Master Processor: Handles all lower level operations like Motor Control and VexNet Communication.
Make sure you have the following first:
1. A USB A-A cable.
2. A charged robot battery
3. The cortex Powered Off
4. Latest version of ROBOTC installed on PC
06/2012 Tanya Mishra 39
Step 1: Connect Cortex and PC
using A-A cable. Step 2: Turn Cortex ON. Step 3: Go to ROBOTCRobot->Platform Type->Innovation First(IFI)->Vex 2.0 Cortex
06/2012 Tanya Mishra 40
Step 4: View->Select Communication Port->USB wired Cable or Vex Robotics COMM Port (if Cortex recognized) otherwise Automatic
Step 5: Robot->Download Firmware->Automatically update Vex Cortex
06/2012 Tanya Mishra 41
Update Firmware on Joystick: Make sure you have the following first:
1. A USB A-A cable.
2. Latest version of ROBOTC installed on PC Step 1: Connect Joystick and PC
using A-A cable. Step 2: Go to ROBOTCRobot->Platform Type->Innovation First(IFI)->Vex 2.0 Cortex
06/2012 Tanya Mishra 42
Step 4: View->Select Communication Port->USB wired Cable or Vex Robotics COMM Port (if Cortex recognized) otherwise Automatic
Step 5: Robot->Download Firmware->Automatically update VexNET Joystick
06/2012 Tanya Mishra 43
Download Firmware when: You start using a particular Vex Cortex or
VexNET Joystick You update a newer version of ROBOTC.
06/2012 Tanya Mishra 44
Download Sample Program
Step 1: Go to ROBOTCFile->Open Sample Program->Training Samples->Motor port 3
forward.c
06/2012 Tanya Mishra 45
Before Downloading, make sure: Your cortex and VexNet remote control are
paired and equipped with VexNet USB keys. Batteries connected to remote control and
cortex. Robot propped up. Orange programming kit connecting PC and
remote control. Turn on Remote Control and Robot. Robot and VexNet status lights should blink
green on both remote control and Robot.
06/2012 Tanya Mishra 46
Step 2: View->preferences->Detailed Preferences->Platform: Vex 2.0 Cortex and Communication Port: Prolific USB-Serial Comm port.
Step 3: Robot->Vex Cortex Communication Mode->VexNet or USB
06/2012 Tanya Mishra 47
Step 4: Robot->Compile and Download Program
Step 5:Debugger Window->Start
06/2012 Tanya Mishra 48
Motorstask main()
{
motor[port3] = 127;
motor[port2] = 127;
wait1Msec(3000);
}
Running this program makes the Robot spin because the motors on the robot are mirrored. So making the motor on port2 move forward in the code, makes it move in reverse in real time.
06/2012 Tanya Mishra 49
Reverse Motor Polarity: Robot->Motors and Sensors Setup->Motors
tab-> Port 2 reversed check box is checked.
06/2012 Tanya Mishra 50
#pragma config(Motor, port2, , tmotorNormal, openLoop, reversed)
The “pragma” statement contains configuration information from the motors and sensors settings and should only be changed from the window.
06/2012 Tanya Mishra 51
The Motors and Sensor Window can also be opened by double clicking on the pragma statement.
Motors and Sensor Window: Name: Name of the Motor eg. leftMotor, rightMotor
Type : Motor Equipped or Type of Motor
Reversed: Checked if Motor needs to be reversed.
task main()
{
motor[leftMotor] = 127;
motor[rightMotor] = 127;
wait1Msec(3000);
}
06/2012 Tanya Mishra 52
06/2012 Tanya Mishra 53
Assigning Positive power Values(127) on both motors makes the robot go forward.
Lower speed of robot by assigning values less than full power(127).
Assigning negative power values(-127) on both motors makes the robot go reverse.
Assigning zero power values(0) on both motors makes the robot stay in place.
Turning of Motors
06/2012 Tanya Mishra 54
Point Turn: Turn in place (-63 and 63)
Swing Turn: Making one motor on and the other off makes the robot swing around the stationary wheels. (0 and 63)
06/2012 Tanya Mishra 55
Sometimes the power assigned in the code to the motors does not reach the motors. Reasons: friction or construction. Manual adjustments to the power levels.
task main()
{
//Makes the robot go forward at half speed for 2 seconds.
motor[leftMotor] = 63;
motor[rightMotor] = 63;
wait1Msec(2000);
//Makes the Robot turn left in place for 0.7 seconds.
motor[leftMotor] = -63;
motor[rightMotor] = 63;
wait1Msec(700);
}
06/2012 Tanya Mishra 56
Shaft Encoders/Rotation Sensor
Manual adjustments of power are not same for all robots and as the battery power drains, the robot is move shorter distances.
Shaft Encoders are used to control how far the Robot Moves.
Number of counts per Revolution on a axle mounted through the encoder center.
Max 360 up for forward movements and 360 down for reverse movements.
06/2012 Tanya Mishra 57
ROBOTC->File->Open Sample Program->Shaft Encoder->Forward for Distance.c
06/2012 Tanya Mishra 58
06/2012 Tanya Mishra 59
Encoders need to be set to zero before you use them.
On the Cortex Micro controller, the Analog and Digital Ports are used to connect sensors.
In Motors and Sensors setup: Digital Port, Sensor Name and Sensor Type Naming Conventions: No special Characters,
No spaces and Not a reserved word in ROBOTC.
Both Encoder wired on the Right and Left side of the robot must be in neighboring ports.
06/2012 Tanya Mishra 60
06/2012 Tanya Mishra 61
Clear the encoders for better consistency and precision on your robots movements.
06/2012 Tanya Mishra 62
Sensor Debug Window: In order to see the values in the encoders as
the robot runs, we can use the debugger window.
Compile and Download the program. Press “continuous” on the debugger window
instead of “start”. Robot->Debugger Windows->Sensors Scroll down and find your encoders in the list. Press “start” on the debugger window to start
your robot and watch the values change.
06/2012 Tanya Mishra 63
06/2012 Tanya Mishra 64
Forward movement and Turning: Not controlled by power or time but rotation
counts.
06/2012 Tanya Mishra 65
Joystick Mapping
Vex Remote control provides you with two joysticks (each having a x- axis and y-axis), eight buttons on the front and four additional buttons on the top.
06/2012 Tanya Mishra 66
The remote control sends streams of data to the Robot over the VexNet.
The Vertical motion of the joysticks on the remote control range from +127 to -127, where +127 is full power forward, 0 is stop and -127 is full power reverse.
To access the values in the joystick in ROBOTC, we use the following command:
vexRT[channel Number]
VexRT is short for Vex Remote Transmitter. The channel number for each input is shown on
the remote.
06/2012 Tanya Mishra 67
For example, the right joystick's vertical motion is on channel 2.
vexRT[ch2]
Pairing each motor with each joystick we can make the robot move forward, turn or go in reverse.
motor[port number] = vexRT[channel number]
06/2012 Tanya Mishra 68
Sample Program:ROBOTC->file->Open Sample Program->Remote Control->Dual
Joystick Control.c
06/2012 Tanya Mishra 69
06/2012 Tanya Mishra 70
Limiting the range of power from [127, -127] to half power [63,-63] to achieve accurate movements.
Similarly, many other possible mapping combinations are possible.
06/2012 Tanya Mishra 71
Timers
Timers are like “Stopwatches”. Used in competition to know how long the robot
has been working. Four Timers provided in ROBOTC: T1 , T2, T3
and T4.ClearTimer(TimerName)
This command resets the Timer to 0 and immediately starts counting again.
06/2012 Tanya Mishra 72
To check the elapsed time on the Timer T1, we use the following command:
time1[T1]
It returns the elapsed time in milliseconds. To check elapsed time in 10 milliseconds or
100 milliseconds, the commands are:
time1[T1], time10[T1], or time100[T1]
06/2012 Tanya Mishra 73
Thus, to make your robot unresponsive for 90 seconds:
06/2012 Tanya Mishra 74
Buttons Mapping
The 8 buttons on front of the remote control are divided into two groups and the four buttons on top are also divided into two groups. The group number is written next to the numbers.
06/2012 Tanya Mishra 75
Unlike joysticks, the buttons have two values: 1 when pressed and 0 when released.
VexRT[Btn Group# Direction],
where Direction = U(Up), D(Down), L(Left), R(Right)
For example, to access the Down button on Group 7 (Left side buttons on the remote):
VexRT[Btn 7 D]
06/2012 Tanya Mishra 76
To make your robot respond to user control on a button press:
06/2012 Tanya Mishra 77
Sensor Configuration
Vex Cortex allows us to incorporate various sensors on the robot which provides valuable sensor feedback for intelligent decision making.
There are 8 Analog Sensor ports for sensors like Line Follower, Accelerometer and Potentiometer.
There are 12 Digital Sensor ports for sensors like the limit switch, Shaft Encoder and Ultrasonic Rangefinder.
06/2012 Tanya Mishra 78
06/2012 Tanya Mishra 79
These sensors are configured in the same way we have configured motors and shaft encoders before.
The ROBOTC Motors and Sensors setup allows you to setup these sensors depending on if it is a Digital or Analog Sensor.
If you are unsure of the type of sensor being Analog or Digital, you can see it in the drop down menus in the Motor and Sensor Setup.
06/2012 Tanya Mishra 80
Limit Switch: Limit Switch is a Digital Sensor(0 and 1) and is
plugged into the Digital port 6 on the Cortex. When pressed, it provides a sensor value 1,
when released, it provides a sensor value 0.SensorValue[Limit switch name]
06/2012 Tanya Mishra 81
Potentiometers: A potentiometer is a Analog Sensor and is
plugged into port 6 of the Analog board on the cortex.
It measures rotation between 0 to 250 (not 360 due to internal mechanical stops) degrees and return value ranging from 0 to approximately 4095.
06/2012 Tanya Mishra 82
The values returned by the Potentiometers can be seen using the Sensor Debug Window that we used with the Shaft encoders.
SensorValue[Potentiometer name]
06/2012 Tanya Mishra 83
Ultrasonic Range Finder Ultrasonic Range Finder allows us to sense
obstacles in the path of the robot and avoid bumping into them.
06/2012 Tanya Mishra 84
It measures distance to the obstacle using sound waves. It calculates the Distance depending on how long it takes for the sound wave to bounce back.
Distance = Speed * Time / 2
Digital Sensor and connections on the Cortex are as follows:
06/2012 Tanya Mishra 85
Motors and Sensor Setup: Choose type depending on what distance scale
you want: cm or mm or inch
06/2012 Tanya Mishra 86
According to the program, till the distance to the obstacle is greater than 25 cm, the robot will move forward. As soon as it is 25 cm away from the obstacle, to robot will stop.
06/2012 Tanya Mishra 87
Sometimes the echo of the sound wave does not reach the range finder on soft surfaces like a sweater or certain surfaces such as a slope deflect the wave in another direction.
In the debugger window, we can see that when the sonar does not detect any sound, the sensor value if set to -1.
06/2012 Tanya Mishra 88
If the sonar value will be -1, the condition in the code will always be false and the robot will not move when no obstacle is detected.
To make the robot move forward when no obstacle is detected, the condition needs to be changed.
06/2012 Tanya Mishra 89
Line Tracking Sensors
Below is shown a set of three Line tracking Sensors. Line tracking sensors work on the bases of Infrared Light. Each sensor has an Infrared LED and an Infrared Light sensor.
06/2012 Tanya Mishra 90
The LED emits light and the sensor detects the amount the light reflected back.
Light Surfaces = Low Sensor Reading Dark Surfaces = High Sensor Reading
06/2012 Tanya Mishra 91
The cortex gives a Sensor reading from 0 to 4095. The value does not correspond to any unit of measurement.
Thus it is important to take care of lighting conditions around the robot and the height at which the sensors are placed in order to determine the threshold of reading.
06/2012 Tanya Mishra 92
Motors and Sensor Setup:
06/2012 Tanya Mishra 93
Calculate Threshold Values (Example): Leaving the task main() empty, if we run the
robot on a light surface, we get the the following values in the Sensor Debugger Window:
For Dark Surfaces we get the following values:
06/2012 Tanya Mishra 94
Light Surface Average Value:
Average = 165 + 167 + 160 = 492 /3 = 164
Dark Surface Average Value:
Average = 2795 + 2821 + 2837 = 8453 / 3 = 2817.66 ~ 2818
Threshold Value:
164 + 2818 = 2982 / 2 = 1491
06/2012 Tanya Mishra 95
Using all three sensors allows us to detect the line as well as border of the line, corners and intersections, which is not possible if you use just one line tracking sensor.
06/2012 Tanya Mishra 96
Sample Program:File->Open Sample Program->VEX2->Training Samples->Simple
Line Tracking.c
06/2012 Tanya Mishra 97
06/2012 Tanya Mishra 98
We can see that the motor value pairs of 0 and 40 cause the robot to make sharp swings as it steers itself on to the line. This causes waste of energy. To simplify, use pairs of motor values close enough lie 20 and 40.
For sharp turns and curves on the lines, we can optimize the motor values, shaft encoder rotation counts and threshold values to work together in order to perfect the different sections of the path.
06/2012 Tanya Mishra 99
Tips on Line Tracking: Break the entire path into sections depending
on how the line curves. Instead of programming the entire path at once,
implement and test each section one after another.
The behaviour in each section will almost eb the same. The only difference will be the values of the motors, encoders or threshold. This can be achieved by implementing a LineTracking() function with different parameter values!
06/2012 Tanya Mishra 100
Reserved words
Motors
Motor control and some fine-tuning commands. motor[output] = power;
The VEX has 8 motor outputs: port1, port2... up to port8. The VEX supports power levels from -127 (full reverse) to 127 (full forward). A
power level of 0 will cause the motors to stop.
bMotorReflected[output] = 1; (or 0;)
06/2012 Tanya Mishra 101
Timing
The VEX allows you to use Wait commands to insert delays into your program. It also supports Timers, which work like stopwatches; they count time, and can be reset when you want to start or restart tracking time elapsed.
wait1Msec(wait_time);
Maximum wait_time is 32768Msec, or 32.768 seconds.
06/2012 Tanya Mishra 102
wait10Msec(wait_time);
Maximum wait_time is 32768, or 327.68 seconds.
time1[timer]
It returns the current value of the referenced timer as an integer. The maximum amount of
time that can be referenced is 32.768 seconds The VEX has 4 internal timers: T1, T2, T3, and T4.
time10[timer]
The maximum amount of time that can be referenced is 327.68 seconds.
06/2012 Tanya Mishra 103
time100[timer]
The maximum amount of time that can be referenced is 3276.8 seconds.
ClearTimer(timer);
This resets the referenced timer back to zero seconds.
SensorValue(sensor_input)
SensorValue is used to reference the integer value of the specified sensor port. Values will correspond to the type of sensor set for that port. The VEX has 16 analog/digital inputs: in1, in2... to in16
06/2012 Tanya Mishra 104
Type of Sensor Digital/Analog? Range of Values
Touch Digital 0 or 1
Reflection (Ambient) Analog 0 to 1023
Rotation (Older Encoder) Digital 0 to 32676
Potentiometer Analog 0 to 1023
Line Follower (Infrared) Analog 0 to 1023
Sonar Digital -2, -1, and 1 to 253
Quadrature Encoder Digital -32678 to 32768
Digital In Digital 0 or 1
Digital Out Digital 0 or 1
06/2012 Tanya Mishra 105
Sounds
The VEX can play sounds and tones using an external piezoelectric speaker attached to a motor port.
PlayTone(frequency, duration);
This plays a sound from the VEX internal speaker at a specific frequency (1 = 1 hertz) for a specific length (1 = 1/100th of a second).
06/2012 Tanya Mishra 106
Radio Control
ROBOTC allows you to control your robot using input from the Radio Control Transmitter.
BvexAutonomousMode = <value>;
Set the value to either 0 for radio enabled or 1 for radio disabled (autonomous mode). You can also use “true” for 1 and “false” for 0.
vexRT[joystick_channel]
This command retrieves the value of the specified channel being transmitted.
06/2012 Tanya Mishra 107
If the RF receiver is plugged into Rx 1, the following values apply:
Control Port Joystick Channel Possible Values
Right Joystick, X-axis
Ch1 -127 to 127
Right Joystick, Y-axis
Ch2 -127 to 127
Left Joystick, Y-axis
Ch3 -127 to 127
Left Joystick, X-axis
Ch4 -127 to 127
Left Rear Buttons Ch5 -127, 0, or 127
Right Rear Buttons
Ch6 -127, 0, or 127
If the RF receiver is plugged into Rx 1, the following values apply:
If the RF receiver is plugged into Rx 2, the following values apply:
06/2012 Tanya Mishra 108
Control Port Joystick Channel Possible Values
Right Joystick, X-axis
Ch1Xmtr2 -127 to 127
Right Joystick, Y-axis
Ch2Xmtr2 -127 to 127
Left Joystick, Y-axis
Ch3Xmtr2 -127 to 127
Left Joystick, X-axis
Ch4Xmtr2 -127 to 127
Left Rear Buttons Ch5Xmtr2 -127, 0, or 127
Right Rear Buttons
Ch6Xmtr2 -127, 0, or 127
bVexAutonomousMode = false; //enable radio control while(true) {
motor[port3] = vexRT[Ch3]; //right joystick, y-axis //controls the motor on port 3 motor[port2] = vexRT[Ch2]; //left joystick, y-axis //controls the motor on port 2
}
06/2012 Tanya Mishra 109
Reference
VEX Cortex Video Trainer using ROBOTC[http://www.education.rec.ri.cmu.edu/products/teaching_robotc_cortex/index.html]
ROBOTC : A C Programming language for Robotics
[http://www.robotc.net/]