rno

Alcatel BSS

A9156 RNO & A9157 LASER -

Preliminary PC Installation

NPA/RNO/LASER Document

Installation Manual

Release B8

3BK 17421 4031 RJZZA Ed.08

Status RELEASED

Short title Installation Manual

All rights reserved. Passing on and copying of this document, useand communication of its contents not permitted without writtenauthorization from Alcatel/Evolium.

BLANK PAGE BREAK

2 / 64 3BK 17421 4031 RJZZA Ed.08

Contents

ContentsPreface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71 General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

1.1 Principles of the Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101.2 Scenario . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101.3 Procedure Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

1.3.1 Pre-requisites . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101.3.2 Restrictions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101.3.3 Initial Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101.3.4 Sequence of Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101.3.5 Final Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111.3.6 Necessary Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111.3.7 Schedule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121.3.8 Impact on Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

1.4 Supplies, Tools and Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121.5 Before to Start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131.6 Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

2 PI 01 - Preliminary Checks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152.1 Check Windows 2000/XP Booting Process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162.2 Check Disk Partitioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162.3 Check RAID5 Activation on Compaq Proliant ML530 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 172.4 Check RAID5 Activation on HP Proliant ML370 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

3 PI 02 - PC Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 193.1 Window 2000 Server Installation on Compaq Proliant ML530 . . . . . . . . . . . . . . . . . . . . . . . . . . 20

3.1.1 Boot with Compaq SmartStart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 203.1.2 Install Compaq Array Configuration Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

3.2 Windows 2000 Server Installation on HP Proliant ML370 G3 . . . . . . . . . . . . . . . . . . . . . . . . . . . 233.2.1 Boot with HP SmartStart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 233.2.2 Install HP Array Configuration Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

3.3 Windows 2000 Server Installation on HP Proliant ML370 G4 . . . . . . . . . . . . . . . . . . . . . . . . . . . 253.3.1 Boot with HP SmartStart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 253.3.2 Install HP Array Configuration Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

3.4 Windows 2000 Professional Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 273.5 Windows XP Professional Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 293.6 Assign L: for CD-ROM Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 323.7 Create D: Partition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 333.8 Install Windows Service Pack 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

4 PI 03 - Customize and Check Windows 2000/XP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 354.1 Windows 2000 Server Customization and Checks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

4.1.1 Customize and Check Network Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 364.1.2 DNS Server Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 374.1.3 Active Directory Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 414.1.4 Set Time Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 434.1.5 Create Users . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 434.1.6 Check Date/Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 454.1.7 Check Regional Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 454.1.8 Check Display Properties for Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 454.1.9 Install TCP/IP Printer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

4.2 Windows 2000 Professional Customization and Checks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 474.2.1 Customize and Check Network Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 474.2.2 Connect Clients to Domain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 484.2.3 Create Users for RNO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 494.2.4 Create Users for LASER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

3BK 17421 4031 RJZZA Ed.08 3 / 64

Contents

4.2.5 Check Date/Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 514.2.6 Check Regional Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 514.2.7 Check Display Properties for Workstation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 514.2.8 Install TCP/IP Printer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

4.3 Windows XP Professional Customization and Checks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 544.3.1 Customize and Check Network Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 544.3.2 Activate Windows XP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 554.3.3 Create Users for LASER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 554.3.4 Check Date and Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 564.3.5 Check Regional Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 564.3.6 Check Display Properties for Workstation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 574.3.7 Install TCP/IP Printer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

5 PI 04: Third Party Software Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 595.1 ARCserve 11 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 605.2 Microsoft Office 2000 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 625.3 Internet Explorer Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

4 / 64 3BK 17421 4031 RJZZA Ed.08

Tables

TablesTable 1: If Windows 2000 is installed and well partitioned . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11Table 2: If Windows 2000 is not (well) installed/partitioned . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

3BK 17421 4031 RJZZA Ed.08 5 / 64

Tables

6 / 64 3BK 17421 4031 RJZZA Ed.08

Preface

PrefacePurpose This document describes the installation and customization of Windows 2000

for further A9156-RNO and A9157-LASER software kits installation.

Whats New In Edition 08Introduction of the HP XW4300 workstation in Windows 2000 ProfessionalInstallation (Section 3.4).

In Edition 07Add section Install Windows Service Pack 4 (Section 3.8).

In Edition 06Add section Windows 2000 Server Installation on HP Proliant ML370 G4(Section 3.3) with Smartstart 7.1.

In Edition 05Add section to configure the Internet Explorer. See Internet ExplorerConfiguration (Section 5.3)

In Edition 043BKA55CBR142966 - End-Of-Life for ARCserve 9 (replacement withARCserve 11).

In Edition 03Windows 2000 default Administrators password is changed.Describe the Windows XP installation and customisation for LASER Client.3BKA55CBR126481 - Introduction of the HP XW4100 workstation for Clientand Standalone machines.

3BK 17421 4031 RJZZA Ed.08 7 / 64

Preface

Audience This document is intended for:

Field service technicians.

Project managers.Site administrators.

System support engineers (specialists).Occasional users (e.g. subcontractors).

Assumed Knowledge You must have a basic understanding of the followings:

Windows 2000 Administration.Installation tools and materials.

TCP/IP knowledge.

8 / 64 3BK 17421 4031 RJZZA Ed.08

1 General Information


This chapter provides general information about the principle of the operationsand requirements for the procedure.

3BK 17421 4031 RJZZA Ed.08 9 / 64


1.1 Principles of the OperationThis document describes the preliminary tasks to be performed before to installan A9156-RNO or A9157-LASER software kit on a PC machine.This document describes also the common third party software installationfor A9156-RNO and A9157-LASER application.

1.2 ScenarioOnly one scenario exists.This method contains the tasks to be performed in order to install andcustomize Windows 2000/XP.

PI01 Preliminary Checks

PI02 PC Installation

PI03 Customize and Check Windows 2000/XP

PI04 Third Party Software Installation.

1.3 Procedure Information

1.3.1 Pre-requisitesPC machine is connected to Power Supply and LAN.

Respect the safety rules.

Inform the operator. Ask for an operators representative to be on site(unless otherwise specifically agreed in writing).

1.3.2 RestrictionsNone.

1.3.3 Initial StatusIt is possible to have Windows 2000 already installed.

Depending on the configuration of Windows 2000, the PC machine will beinstalled from scratch or just customized.

1.3.4 Sequence of Operations

Procedure Name Mandatory/Optional

PI01 - Preliminary Checks Mandatory

10 / 64 3BK 17421 4031 RJZZA Ed.08



PI03 - Customize and Check Windows 2000/XP Mandatory

PI04 - Third Party Software Installation Mandatory

Table 1: If Windows 2000 is installed and well partitioned


PI01 - Preliminary Checks Mandatory

PI02 - PC Installation Mandatory

PI03 - Customize and Check Windows 2000/XP Mandatory

PI04 - Third Party Software Installation Mandatory

Table 2: If Windows 2000 is not (well) installed/partitioned

1.3.5 Final StatusOn each configuration requested, Windows 2000 is installed, customizedand with corresponding third party software on it.

For Standalone and Client configuration the operating system used isWindows 2000 Professional.

For Server configuration the operating system used is Windows 2000 Server.

1.3.6 Necessary InformationThe PC machine needs the following information:

IP Address

Netmask

Gateway

Hostname (NetBIOS Computer Name)DNS IP Address

DNS Suffix (for Client/Server configuration only)If a registered domain suffix is not available use the default one:..

Domain name (default: rnov4 or laser)IP address of printer to be used.

Administrator password if Windows 2000 already installed.

3BK 17421 4031 RJZZA Ed.08 11 / 64


1.3.7 Schedule

PI No. PI Titles Total Time

PI 01 Preliminary Checks 10 min./machine

PI 02 PC Installation 80 min./machine

PI 03 Customize and Check Windows 2000/XP 80 min./ server60 min./ client60 min./ standalone

PI 04 Third Party Software Installation 40 min./machine

TOTAL 3 h 30 min / Server3 h / Client3 h / Standalone

1.3.8 Impact on ServiceNone.

1.4 Supplies, Tools and DocumentationSupplies No supplies needed.

Tools

Designation Version

Windows Server CD-ROM 2000

Windows Professional CD-ROM 2000 (or XP) (*)Compaq SmartStart Server Profile Diskette

Compaq SmartStart for Server CD-ROM 5.10 (or higher)HP SmartStart for Server CD-ROM 6.3 or 7.1

SCSI drivers (if needed)In case of Client/Standalone installation

see SPS

Network Card DriverIn case of Client/Standalone installation

see SPS

Video Card DriverIn case of Client/Standalone installation

see SPS

12 / 64 3BK 17421 4031 RJZZA Ed.08


Designation Version

Printer Driver see SPS

ARCserve CD-ROM 11

(*) Only for LASER configuration.Applicable Documents

No. Designation Reference

[1] Completion Check List (CCL) 3BK 17421 4031 QZZZA[2] B8 Technical Status Information (TSI) 3BK 17421 0003 PCZZA[3] B8 Site Preparation Sheet (SPS) 3BK 17421 4002 RJZZA

1.5 Before to StartThe sequence of this method consists in the result of "PI01: PreliminaryChecks".Depending of PI01s results, the applicability of the next PIs are describedbelow:

if PI01 is NOK then apply { P02, PI03 and PI04 }if PI01 is OK then apply { PI03 and PI04 }

1.6 ConventionsThe following conventions are used in the document:

Keyboard keys are indicated in the text as [ XX ]. For example, Press[ Enter ] means press the [ Enter ] key.System messages appear in Courier font:system message

Operator input is shown after a double right-oriented arrow, in Courier font.The Windows 2000 command prompt looks like the following:

C:\>

Software buttons on a terminal screen are also indicated in the text as [ XX ].For example, click on [ OK ] means move the mouse pointer to the [ OK ]button on the screen and then click the left mouse.

To describe a menu path chain, the menu entries are chained with a ->.Example:Tools > Options > Printer -> ...

3BK 17421 4031 RJZZA Ed.08 13 / 64


14 / 64 3BK 17421 4031 RJZZA Ed.08

2 PI 01 - Preliminary Checks


This chapter describes the preliminary checks to be performed in order to find ifWindows is already installed and correct partitioned.

Apply this PI for any configuration to be installed (Windows 2000 Server orProfessional).

3BK 17421 4031 RJZZA Ed.08 15 / 64


2.1 Check Windows 2000/XP Booting Process1. Switch on the PC machine.2. Let the system boot .3. Check that Log On window appears after some minutes.4. If Log On windows not appear continue with PI 02 - PC Installation.5. Update the Completion Check List (CCL).

2.2 Check Disk Partitioning1. Log in as Administrator (find password in SPS).2. Go on the menu path:

Start > Settings > Control Panel3. Double click on Administrative Tools icon.4. In Administrative Tools window, double click on Computer Management icon.5. In Computer Management window, select Disk Management.

The disk partitions will be displayed on the left window.6. Check the following partitions are created, at the Disk 0 line:

The C: partition must be 4 GB NTFS for Server, Client or Standaloneconfiguration.

The D: partition must be NTFS with the remaining disk space for Server,Client or Standalone configuration.

7. If disk is not correct partitioned continue with PI 02 - PC Installation.8. Update the Completion Check List (CCL).

16 / 64 3BK 17421 4031 RJZZA Ed.08


2.3 Check RAID5 Activation on Compaq Proliant ML530

This paragraph is applicable only for Server configuration.

To check the RAID5 configuration:

For Compaq Proliant

ML530

1. Follow the menu path:Start > Programs > Compaq System Tools > Compaq ArrayConfiguration UtilityIf path specified above is not available perform following steps:

Insert SmartStart for Servers Compaq CD-ROM in drive.

Restart the PC.System will boot from Compaq SmartStart CD-ROM.

In System Utilities window:Double click on Run Array Configuration Utility icon.

2. In Compaq Array Configuration Utility windows a line contains RAID5must appear like that:xxxx Mb, RAID 5, Logical drive 1

3. If RAID5 is not correct configured continue with PI 02 - PC Installation.If the configuration is OK go to PI 03 - Customize and Check Windows2000/XP.

4. Close Compaq Array Configuration Utility window.If the system was booted from Compaq SmartStart CD-ROM:

Exit System Utilities clicking on [ Exit ]. Confirm, clicking on [ OK ].Remove CD-ROM from drive.

Press any key to restart the system.

5. Update the Completion Check List (CCL).

3BK 17421 4031 RJZZA Ed.08 17 / 64


2.4 Check RAID5 Activation on HP Proliant ML370

This paragraph is applicable only for Server configuration.

To check the RAID5 configuration:

For HP Proliant ML370 1. To check the RAID5 configuration, follow the menu path:Start > Programs > Compaq System Tools > hp Array ConfigurationUtility > hp Array Configuration UtilityA new Array Configuration Utility (ACU) icon appears on the taskbar.

2. Right click on ACU icon, then choose Open Local ACU Client option.An Internet Explorer is opened.

Note: If Internet Explorer was never launched, follow the wizards steps to open anew session.3. In Security Alert window :

Select In the future, do not show this warning option.

Click on [ OK ].

4. At the question Do you want to proceed ? Answer Yes.The Internet Explorer is opened with System Management Homepagefor ML370.

5. In Account Login section:

Choose administrator from drop-down menu (if not already).Type the administrators password.In case of RNO machine, the default password is rnoadm.In case of LASER machine, the default password is laseradm.

Click on [ OK ].

6. Wait and in the new Internet Explorer window is displayed the SCSIconfiguration. The last line must be:Logical Drive 1 (xxxxx MB, RAID5)

7. If RAID5 is not correct configured or detected continue with PI 02 - PCInstallation.If the RAID5 configuration is OK go to PI 03 - Customize and CheckWindows 2000/XP.


18 / 64 3BK 17421 4031 RJZZA Ed.08

3 PI 02 - PC Installation


This chapter describes the operations to be performed for installation ofWindows 2000 on Server and Workstation.

Apply this PI only if checks performed in "PI01 - Preliminary Checks" wereNOK.

3BK 17421 4031 RJZZA Ed.08 19 / 64


3.1 Window 2000 Server Installation on Compaq Proliant ML530This section is intended for Server configuration only.

The method will not describe all the step to follow to perform the installationbecause is depending to the hardware to be installed. Follow the installation byclicking on [ Continue ], [ Next ] or press [ Enter ] buttons. When special actionmust be performed they will be mentioned in the method.

3.1.1 Boot with Compaq SmartStartStart Installation 1. Perform a copy of Compaq SmartStart Server Profile diskette on a

separate PC machine.2. Boot with Compaq SmartStart for Servers CD-ROM.

If the System Utilities window is displayed double click on Run System EraseUtility window and confirm all the question to delete current configuration.When erase process is finished restart installation.If no previous installation was found the language selection window willbe displayed.

3. Choose English language.4. Enter regional settings and continue installation. Be careful to enter the

right date !5. Check the box labeled I agree asking about the license and continue

installation.6. Choose Assisted Integration then click on [ Begin ].7. When asked, insert the copy of Compaq SmartStart Server Profile diskette:

Click on [ Next ].8. Double click on Microsoft and then select Microsoft Windows 2000 Server -

English:Click [ Next ] button to continue the installation.

9. Select Continue with SmartStart and press [ Enter ].Configure Smart Array 1. The window Compaq SmartStart Array Configuration Utility appears.

Select [ Continue ] and follow installation.2. Select Smart Array Controllerand click on [ Next ].3. Choose RAID5 in Select A Configuration window.

Click on [ Continue ] to follow installation and at the end of configurationclick [ Finish ].

4. System reboots two times.

Configure Windows 1. In Compaq SmartStart Product Selection window choose Install softwarefrom CD only.Click on [ Next ] and follow installation.

2. Do not select creation of replication profile:Click [ Next ] and continue installation.

3. A window Hardware Configuration Options appears. Continue the AutomaticServer Recovery and Integrated Remote Console installation by clicking on[ Next ] button few times. At the end, click [ Continue ].

20 / 64 3BK 17421 4031 RJZZA Ed.08


4. In Windows 2000 Server Disk Carving Interview window, set boot partition to4096 MB and NTFS. Click on [ Continue ].

5. In Microsoft Windows 2000 Server Setup, choose Per Server and forNumber of Concurrent Connections enter 50:Click on [ Next ].

6. In Microsoft Windows 2000 Server Setup enter the product key.Find product key in SPS.Click on [ Continue ].

7. In Diskette Builder window, select [ Continue ] and follow installation.8. Pre-Installation window will be displayed:

Click on [ Continue ].The system will reboot. During boot, the system partition is gettingformatted.

Personalize Windows 1. When asked, insert Windows 2000 Server CD-ROM, and click on [ OK ].Windows 2000 installation files are copied to hard disk. A progress bar isdisplayed on the screen.

2. When asked, remove CD-ROM and diskette, then click [ OK ].System will reboot. After reboot windows installation continue. After, systemreboot again two times to convert primary partition to NTFS.

3. Welcome to the Windows 2000 Setup Wizard window will be displayed:Click on [ Next ].

4. If Digital Signature Not Found window is displayed:Click on [ Yes ].

5. Regional Settings window is displayed:Click on [ Next ].

6. Personalize Your Software window is displayed:

Enter Name + Organization. Find organization in TSI.

Click [ Next ].

7. In Computer Name and Administrator Password window:

Enter Computer name, find it in SPS (in case of RNO Server migrationfind the computer name in CCL of migration method).For the Administrator password and Confirm password fields:In case of RNO machine, type rnoadm.In case of LASER machine, type laseradm.

Click [ Next ].

8. In Date and Time Settings:

Check the date and time and enter the right one if are not correct.

Check and select the right Time Zone if not correct

Click on [ Next ].

3BK 17421 4031 RJZZA Ed.08 21 / 64


Network Configuration 1. In Workgroup or Computer Domain window:

Select No, this computer is not on a network or is on a network without adomain.Enter the name of the future domain in Workgroup or Computer Domainfield. Find it in SPS (in case of RNO Server migration find the Domainname in CCL of migration method).Click on [ Next ].

2. The Completing Windows 2000 Server Wizard window will be displayed:Click on [ Finish ].Computer will reboot.

3. After reboot, Welcome to the Network Identification Wizard window isdisplayed:Click on [ Next ].

4. In Users of This Computer window:

Select Users must enter a user name and password to use thiscomputer.

Click [ Next ].

5. In Completing the Network Identification Wizard window:Click on [ Finish ].


3.1.2 Install Compaq Array Configuration Utility1. Press [ CTRL ] + [ ALT ] + [ DEL ] .2. Log in as Administrator.

Compaq Installation Utility window is displayed with a progress bar.After installation, the system reboots.


22 / 64 3BK 17421 4031 RJZZA Ed.08


3.2 Windows 2000 Server Installation on HP Proliant ML370 G3This section is intended for Server configuration only.

Ensure the boot sequence starts first with CD-ROM.

3.2.1 Boot with HP SmartStart

The minimum version of HP SmartStart CD is 6.30.

HP SmartStart 1. Insert HP SmartStart CD-ROM in the drive.Wait for the drivers to be loaded automatically.

2. Select English language, click on [ Continue ].3. In End-User License Agreement window, click on [ Agree ].4. In PCI Device Information section,

Check that Smart Array 64x Controller is present.If not, do not continue with the next steps.

Click on [ launch setup ] .

5. In Hardware Configuration window, click on [ Next ].6. In Operating System Family window:

Select Microsoft Windows 2000 Server line

Click on [ Next ].

7. In Boot Partition Size window :

Select file system as NTFS.

Select Custom then type 6144 (size of boot partition).Click on [ Next ].

8. In Operating System Configuration Information window :

Type User Name and Organization as aproppiate

Enter Product Key of Windows 2000 Server

For License Type, choose Per Server, then type 50 for Client Licenses.

Click on [ Next ].

9. In Web-Enabled System Management Password Configuration window:

Type Administrators password and confirm it.

Click on [ Next ].

10. A window titled SmartStart has enough information to install appears,click on [ Continue ].

3BK 17421 4031 RJZZA Ed.08 23 / 64


The system will erase all drives and existing data, create partition, copydrivers on hard disk and install Proliant Support Pack.

Start Installation 1. When asked, remove the HP SmartStart CD and insert the Windows2000 Server CD-ROM in the drive.Follow instructions present on the screen.

2. Let the installation to be done automatically. Do not press any key !The system will copy Windows 2000 files on the hard disk and convert theprimary partition.The system restarts for several times.

3. Wait until the window titled Welcome to Windows 2000 Setup Wizardappears, click on [ Next ].Wait for installing the devices.

4. In Regional Settings window, click on [ Next ].5. In Computer Name and Administrator Password window, type the right

information, then click on [ Next ].6. In Date and Time Settings window, enter the right date, time and timezone,

then click on [ Next ].7. In Workgroup or Computer Domain window:

Select No, this computer is not on a network or is on a network without adomain.

Enter the name of the future domain in Workgroup or Computer Domainfield. Find it in SPS (in case of RNO Server migration find the Domainname in CCL of migration method).Click on [ Next ].

8. When Completing the Windows 2000 Setup Wizard window appears:

Remove the Windows 2000 CD-ROM from the drive (if not already).Click on [ Finish ].

The system restarts.

3.2.2 Install HP Array Configuration UtilityNote: With HP array configuration utility, you can view the SCSI configuration via

HTTP (using Internet Explorer).1. Log in as Administrator.2. The window titled HP Installation Utility is displayed.

Wait until the HP programs are installing and configuring automatically.The machine restarts.


24 / 64 3BK 17421 4031 RJZZA Ed.08


3.3 Windows 2000 Server Installation on HP Proliant ML370 G4This section is intended for Server configuration only.

Ensure the boot sequence starts first with CD-ROM.

3.3.1 Boot with HP SmartStart

The minimum version of HP SmartStart CD is 7.1.

HP SmartStart 1. Insert HP SmartStart CD-ROM in the drive.Wait for the drivers to be loaded automatically.

2. Select English language, click on [ Continue ].3. In End-User License Agreement window, click on [ Agree ].4. In PCI Device Information section,

Check that Smart Array 640x Controller is present.If not, do not continue with the next steps.

Click on [ launch setup ] .

5. In Hardware Configuration window, click on [ Next ].6. In Operating System Selection window:

Click Microsoft Windows 2000 line

Click Microsoft Windows 2000 Server line

Click on [ Next ].

7. In Boot Partition Size window :

Select file system as NTFS.

Select Custom then type 6144 (size of boot partition).Click on [ Next ].

8. In Operating System Configuration Information window :

Type User Name and Organization as aproppiate

Enter Product Key of Windows 2000 Server

For License Type, choose Per Server, then type 50 for Client Licenses.

Click on [ Next ].

9. In SNMP Configuration window, click on [ Next ].10. In Web-Enabled System Management Password Configuration window:

Type Administrators password and confirm it.

Click on [ Next ].

3BK 17421 4031 RJZZA Ed.08 25 / 64


11. A window titled SmartStart has enough information to install appears,click on [ Continue ].The system will erase all drives and existing data, create partition, copydrivers on hard disk and install Proliant Support Pack.

Start Installation 1. When asked, remove the HP SmartStart CD and insert the Windows2000 Server CD-ROM in the drive.Follow instructions present on the screen.

2. Let the installation to be done automatically. Do not press any key !The system will copy Windows 2000 files on the hard disk and convert theprimary partition.The system restarts for several times.

3. Wait until the window titled Welcome to Windows 2000 Setup Wizardappears, click on [ Next ].Wait for installing the devices.

4. In Regional Settings window, click on [ Next ].5. In Computer Name and Administrator Password window, type the right

information, then click on [ Next ].6. In Date and Time Settings window, enter the right date, time and timezone,

then click on [ Next ].7. In Workgroup or Computer Domain window:

Select No, this computer is not on a network or is on a network without adomain.

Enter the name of the future domain in Workgroup or Computer Domainfield. Find it in SPS (in case of RNO Server migration find the Domainname in CCL of migration method).Click on [ Next ].

8. When Completing the Windows 2000 Setup Wizard window appears:

Remove the Windows 2000 CD-ROM from the drive (if not already).Click on [ Finish ].

The system restarts.

3.3.2 Install HP Array Configuration UtilityNote: With HP array configuration utility, you can view the SCSI configuration via

HTTP (using Internet Explorer).1. Log in as Administrator.2. The window titled HP Installation Utility is displayed.

Wait until the HP programs are installing and configuring automatically.The machine restarts.


26 / 64 3BK 17421 4031 RJZZA Ed.08


3.4 Windows 2000 Professional Installation

Apply this section for Client or Standalone configuration only.

The method will not describe all the step to follow to perform the installationbecause is depending to the hardware to be installed. Follow the installation byclicking on [ Continue ], [ Next ] or press [ Enter ] buttons. When special actionmust be performed they will be mentioned in the method.

Boot from Windows

2000 CD-ROM

1. Switch on the PC machine.2. In case of HP XW4300 workstation, insert the

HP Restore Plus CD-ROM and follow the indications on the screen.

Windows 2000 Professional CD-ROM with SP4 only

3. At boot, insert CD-ROM Windows 2000 Professional in CD-ROM drive.When prompted, press any key to boot from CD-ROM.

If you insert your CD-ROM too late, then reboot again the machine. If themachine does not boot from CD-ROM, check in boot setup that CD-ROMis first in Boot Sequence.

If the PC have SCSI hard disk, the SCSI driver must be installed as describedin SCSI Driver Installation, else continue with Start Installation.

SCSI Driver Installation 1. When the Windows 2000 Setup blue window is displayed with followingmessage in the down side:

Press F6 if you need to install a third party SCSI orRAID driver.

Press the [ F6 ] key.2. In next window:

Press [ S ] to specify additional device.Install the drivers for SCSI controller from a floppy disk.

After the drivers was installed, the Windows 2000 Professional installationcontinue as described below.

Start Installation 1. In Welcome to Setup window:Press [ Enter ].

2. In Windows 2000 Licensing Agreement window:Press [ F8 ] to agree.

3. If a previous installation of Windows 2000 is found, it will ask to repairor upgrade it:Press [ Esc ] to continue.

4. In the next window, the system lists the possible existing partitions. Deleteany partition that exists with following sequence:

3BK 17421 4031 RJZZA Ed.08 27 / 64


Select the partition.

Press [ D ], [ Enter ] and [ L ].

5. To create C: partition, perform the next two steps:

Press [ C ].Enter 4096 value as the partition size (in Mb):Press [ Enter ] to create partition.

6. Select C: line for installation of the Windows 2000 Professional, then press[ Enter ].

7. Choose to format the partition using NTFS then press [ Enter ].The hard disk is verified, then some files are copied on the hard disk,andthen system reboots.

Windows 2000

Professional Installation

1. After reboot, the installation starts automatically.2. In Regional Settings window:

Click on [ Next ] button to continue.3. In Personalize Your Software window:

Enter Name & Organization (find in TSI).Click on [ Next ].

4. Enter License Key, then click [ Next ]. Find the License Key on SPS.5. In Computer Name and Administrator Password window:

Enter Computer name, find it in SPS.

For Administrator password and Confirm password fields:In case of RNO machine, type rnoadm.In case of LASER machine, type laseradm.

Click [ Next ].

6. In Date and Time Settings window:

Enter the right date and time.

Select the right Time Zone.

Click on [ Next ].

7. In Network Settings window:

Select Typical settings.

Click on [ Next ].

8. In Workgroup or Computer Domain window:

Select No, this computer is not on a network or is on a networkwithout a domain.

Click on [ Next ].Files will be copied.

28 / 64 3BK 17421 4031 RJZZA Ed.08


9. Completing the Windows 2000 Setup Wizard window is displayed:

Remove CD from drive.

Click on [ Finish ] to restart computer.

Network Identification 1. Welcome to the Network Identification Wizard window is displayed:Click on [ Next ].

2. In Users of This Computer window:

Select Users must enter a user name and password to use thiscomputer.

Click [ Next ].

3. In Completing the Network Identification Wizard window:Click on [ Finish ].


3.5 Windows XP Professional Installation

Apply this section for LASER Client configuration only.

The method will not describe all the steps to perform at the installation becauseis depending to the hardware to be installed. Follow the installation by clickingon [ Continue ], [ Next ] or press [ Enter ] buttons. When special action must beperformed they will be mentioned in the method.

Boot from Windows

2000 CD-ROM

1. Switch on the PC machine.2. At boot, insert CD-ROM Windows XP Professional in CD-ROM drive.

When prompted, press any key to boot from CD-ROM.

If you insert your CD-ROM too late, then reboot again the machine. If themachine does not boot from CD-ROM, check in boot setup that CD-ROMis first in Boot Sequence.

If the PC have SCSI hard disk, the SCSI driver must be installed as describedin SCSI Driver Installation, else continue with Start Installation.

SCSI Driver Installation 1. When the Windows XP Setup blue window is displayed with followingmessage in the down side:

Press F6 if you need to install a third party SCSI orRAID driver.

Press the [ F6 ] key.2. In next window:

Press [ S ] to specify additional device.Install the drivers for SCSI controller from a floppy disk.

3BK 17421 4031 RJZZA Ed.08 29 / 64


After the drivers was installed, the Windows XP Professional installationcontinue as described below.

Start Installation 1. In Welcome to Setup window:Press [ Enter ].

2. In Windows XP Licensing Agreement window:Press [ F8 ] to agree.

3. If a previous installation of Windows XP is found, it will ask to repairor upgrade it:Press [ Esc ] to continue.

4. In the next window, the system lists the possible existing partitions. Deleteany partition that exists with following sequence:

Select the partition.

Press [ D ], [ Enter ] and [ L ].

5. To create C: partition, perform the next two steps:

Press [ C ].Enter 4096 value as the partition size (in Mb):Press [ Enter ] to create partition.

6. Select C: line for installation of the Windows XP Professional, then press[ Enter ].

7. Choose to format the partition using NTFS then press [ Enter ].The hard disk is verified, then some files are copied on the hard disk,and then system reboots.

Windows XP

Professional Installation

1. After reboot, the installation starts automatically.2. In Regional and Language Options window:

Click on [ Next ] button to continue.3. In Personalize Your Software window:

Type the Name & Organization.

Click on [ Next ].

4. Type the Product Key, then click [ Next ]. Find the License Key on SPS.5. In Computer Name and Administrator Password window:

Type the Computer name, find it in SPS.

In Administrator password and Confirm password fields:For the LASER machine, type laseradm.

Click [ Next ].

6. In Date and Time Settings window:

Select the right date and time.

Select the right Time Zone.

Click on [ Next ].

30 / 64 3BK 17421 4031 RJZZA Ed.08


7. In Network Settings window:

Select Typical settings.

Click on [ Next ].

8. In Workgroup or Computer Domain window:

Select No, this computer is not on a network or is on a networkwithout a domain.

Click on [ Next ].Files will be copied.

9. In Display Settings window, click on [ OK ].Windows Activation 1. In Welcome to Microsoft Windows window, click on [ Next ].

2. In conecting to internet window, click on [ Skip ].3. In Ready to activate Windows window:

Select No, remind me every few days

Click on [ Next ].

4. In Who will use this computer window, type laser and click on [ Next ].5. In Thank you window, click on [ Finish ].

The system will reboot.

Switch to Classic View 1. Log in as Administrator and go on the menu path:Start > Control Panel

2. In the left side of the window click on [ Switch to Classic View ].3. In the right side of the window double click on Taskbar and Start Menu icon.4. In Taskbar and Start Menu window:

Select the Start Menu tab

Select the Classic Start menu button

Click on [ OK ].

5. Close the Control Panel window.6. Update the Completion Check List (CCL).

3BK 17421 4031 RJZZA Ed.08 31 / 64


3.6 Assign L: for CD-ROM Drive

Apply this paragraph as Administrator for ALL configurations.

1. Log in as Administrator, if not already logged on.2. Go on the menu path:

Start > Settings > Control Panel3. In Control Panel window, double click on Administrative Tools icon.4. In Administrative Tools window, double click on Computer Management icon.5. In Computer Management window, select Storage > Disk Management.6. Select CD-ROM label (D:).7. To change the drive letter, go on the submenu path:

Action > All Tasks > Change Drive Letter and Paths ...8. In the Change Drive Letter and Paths for (D:) window:

For Windows 2000, click on [ Edit ].For Windows XP, click on [ Change ].

9. In Edit or Change Drive Letter or Path window:

Select L in Assign a drive letter:

Click on [ OK ].In Confirm window, click on [ Yes ].


32 / 64 3BK 17421 4031 RJZZA Ed.08


3.7 Create D: Partition

Perform this paragraph as Administrator for ALL configurations.

Create Partition 1. In Computer Management window select Disk Management (double click onStorage if storage tree is closed).

Select the unallocated space (click on it).Choose:Action > All Tasks > New Partition ...

2. Welcome to the Create Partition Wizard window will be displayed:Click on [ Next ].

3. Select Partition Type window will be displayed:

Select Primary partition

Click on [ Next ].

4. Specify Partition Size window will be displayed:

The maximum disk space is already present.

Click on [ Next ].

5. In Assign Drive Letter or Path window:

Select D for Assign the following drive letter:

Click on [ Next ].

6. Format Partition window will be displayed:

Select Format this partition with the following settings

Select following settings:NTFS for File System to useDefault for Allocation unit sizeData for Volume label

Click on [ Next ].Click on [ Finish ].

Wait for partition to be created and formatted.7. Close the Computer Management window.8. Close the Administrative Tools window.9. Update the Completion Check List (CCL).

3BK 17421 4031 RJZZA Ed.08 33 / 64


3.8 Install Windows Service Pack 4

Perform this paragraph as local Administrator for ALL RNO configurations.

1. Insert the RNO CD-ROM in the drive.2. Open the Windows Explorer.3. Go on the following folder:

L:\3rd Party Software\Windows2000 ServicePack 44. Double click on w2ksp4_en.exe.

Wait for all files extraction.5. In Welcome window, click on [ Next ].6. In License Agreement window:

Select I Agree.

Click on [ Next ].

7. In Select Options window:

Select Do Not Archive Files option.

Click on [ Next ].

8. Wait for system files update.9. In Completing the Windows 2000 Service Pack 4 Setup Wizard window, click

on [ Finish ] to restart the machine.10. Remove the RNO CD-ROM from the drive.11. Update the Completion Check List (CCL).

34 / 64 3BK 17421 4031 RJZZA Ed.08

4 PI 03 - Customize and Check Windows 2000/XP


This chapter describes the operations to customize and checks to do in order toassure that Windows 2000 is correct configured.

Apply this PI as Administrator on each PC machine.

3BK 17421 4031 RJZZA Ed.08 35 / 64


4.1 Windows 2000 Server Customization and Checks

Perform this paragraph only on Server.

4.1.1 Customize and Check Network Parameters1. Log in as Administrator.2. Right click on My Network Places icon.

Select Properties from the pop-up menu.3. In Network and Dial-up Connections window:

Right click on each Local Area Connection icon.

Select Properties from the pop-up menu.

4. In Local Area Connection Properties window:

Select Internet Protocol (TCP/IP).Click on [ Properties ].

5. In Internet Protocol (TCP/IP) Properties window:Check if Use the following IP address: is selected. If is not selected,select it.

Check and modify if needed the value for IP Address, Subnet masksand Default gateway. Find this values in SPS.

In case of installation of Windows 2000 during migration of a RNO Server, findthe values for IP Address, Subnet masks and Default gateway in CCL of themigration method (the values that were on the old machine).

Check if Use the following DNS server addresses: is selected. Ifnot, select it.

In Preferred DNS server field enter its own IP address (same value asentered before for IP address).Click on [ OK ].

6. In Local Area Connections Properties window, click on [ OK ].7. Close Network and Dial-up Connections window.8. Update the Completion Check List (CCL).

36 / 64 3BK 17421 4031 RJZZA Ed.08


4.1.2 DNS Server InstallationConfigure DNS Suffix 1. Open the Properties dialog box for My Computer.

2. In the System Properties dialog box, on the Network Identification tab,click Properties.

3. In the Identification Changes dialog box, click on [ More... ].4. In the DNS Suffix and NetBIOS Computer Name dialog box:

In the Primary DNS Suffix of this computer field enter: .< DNSsuffix>. Find domain name and DNS suffix in SPS .If domain name or DNS Suffix are not present in SPS usethe default values: rnov4.. orlaser.., where rnov4 or laser representthe domain name and . represent theDNS Suffix.

In case of RNO Server migration find the domain name and DNS suffix inCCL of the migration method.

Click on [ OK ].

5. In Identification Changes dialog box:Click on [ OK ].

6. In Network Identification dialog box:Click on [ OK ].

7. Click [ OK ] to close the System Properties dialog box, and then click [ Yes ]button in System Settings Change message box to restart computer.

Install DNS 1. Log in as Administrator.2. In Control Panel , double click Add/Remove Programs icon, and then click

Add/Remove Windows Components icon.3. On the Windows Components page, under Components, select Networking

Services, without to check it, and then click on [ Details ].

If the Domain Name System (DNS) is already selected clear it and click[ OK ]. Follow steps to uninstall DNS. After DNS was uninstalled, restartDNS installation.

4. In Networking Services window:

Verify that all check boxes are cleared. If not then clear all.

Select the Domain Name System (DNS) check box.Click on [ OK ].

5. In the Windows Components Wizard page:Click on [ Next ].

6. If prompted, insert the Windows 2000 Server compact disc and click on[ OK ] button (the new letter of CD drive is L:).

3BK 17421 4031 RJZZA Ed.08 37 / 64


7. After the required files have been copied, click on [ Finish ] button, and thenclose all windows.

Add Forward Lookup

Zone

1. SelectStart -> Programs -> Administrative Tools -> DNS

2. In the console tree, right click , and then click Configurethe server.

3. On the Welcome to the Configure DNS Server Wizard page:Click on [ Next ].

4. On the Root Server page:

Select This is the first DNS server on this network.

Click on [ Next ].

5. On the Forward Lookup Zone page:

Ensure that Yes, create a forward lookup zone is selected.

Click on [ Next ].

6. On the Zone Type page:

Ensure that Standard primary is selected.

Click on [ Next ].

7. On the Zone Name page:

In the Name field enter: . from SPS (in caseof migration find domain name in CCL of migration method), the samevalues used before for Configure DNS Suffix paragraph.Default : rnov4.. orlaser..

If the Windows 2000 installation is performed for a RNO Server migration find and in CCL of migration method.

Click on [ Next ].

8. On the Zone File page:

Ensure that Create a new file with this file name is selected.

Click on [ Next ].

Add Reverse Lookup

Zone

1. On the Reverse Lookup Zone page :

Ensure that Yes, create a reverse lookup zone is selected.

Click on [ Next ].

2. On the Zone Type page:

Select Standard primary.

Click on [ Next ].

38 / 64 3BK 17421 4031 RJZZA Ed.08


3. On the Reverse Lookup Zone page:

Verify that Network ID is selected.

For the network ID, enter the significant octets of the IP address, conformwith the IP network class.

The octets that have to be filled up, in Network ID field, are in white color.

For example, for an IP address of 192.168.1.1, type 192.168.1 .

Click on [ Next ].

4. On the Zone File page:

Ensure that Create a new file with this file name is selected.

Click on [ Next ].

5. On the Completing the Configure DNS Server Wizard page:Click on [ Finish ].

Support Dynamic

Update

1. In the console tree of DNS , expand (where is thecomputer name).

2. In the console tree, expand Forward Lookup Zone, and then click the domain(default domain: rnov4..).

3. Right click on domain and then select Properties.4. In the Properties box:

In the General tab, for Allow dynamic updates field select Yes.

Click on [ OK ].

5. In the console tree, expand Reverse Lookup Zone, and then click the subnet(for example the subnet is : 192.168.1).

6. Right click the subnet and then select Properties.7. In the Subnet Properties box:

In the Allow dynamic updates field select Yes.

Click on [ OK ].

Enable Forwarders 1. In the console tree of DNS , expand (where is thecomputer name), if not already expanded.

This paragraph must be performed only if IP address of a DNS server ispresent in SPS or in CCL of the migration method in case of installation duringRNO Server migration.

2. In the console tree, expand Forward Lookup Zone, and then click the . zone.3. Right click on . zone and then select Delete.4. In DNS window:

Click on [ OK ] button to confirm deletion.5. In the console tree of DNS , right click on (where is

the computer name).

3BK 17421 4031 RJZZA Ed.08 39 / 64


From the pop-up menu select Properties.6. In the Properties window:

In Forwarders tabCheck Enable forwarders check box.Enter DNS IP address from SPS.

If the Windows 2000 installation is performed for a RNO Server migration, findDNS IP address in CCL of the migration method.

Click on [ Add ].

Click on [ OK ].

7. Close DNS window.

Register DNS 1. Open a command prompt:Start -> Programs -> Accessories -> Command Prompt

2. At the command prompt, enter following command:C:\> ipconfig /registerdns

Check DNS 1. At the command prompt enter following command:C:\> nslookup ..

Find the computer name, domain and DNS Suffix in SPS.

In case of RNO Server migration, find computer name and domain name andDNS Suffix in CCL of the migration method.

For example:C:\> nslookup server.rnov4.tm.alcatel

Server: server.rnov4.tm.alcatelAddress: 192.168.1.1Name: server.rnov4.tm.alcatelAddress: 192.168.1.1The DNS server responds with its name and IP address.

2. At the command prompt enter following command:C:\> nslookup

where < IP address> is the IP address of the computer.The DNS server responds with its name and IP address.For example:

C:\> nslookup 192.168.1.1Server: server.rnov4.tm.alcatelAddress: 192.168.1.1Name: server.rnov4.tm.alcatelAddress: 192.168.1.1

For both nslookup commands, if an error message is received or the name andIP address could not be solved, stop installation and call Alcatel TAC level 2.

3. Close Command Prompt window.4. Update the Completion Check List (CCL).

40 / 64 3BK 17421 4031 RJZZA Ed.08


4.1.3 Active Directory InstallationStart Installation 1. Select:

Start -> Run2. In the Run box, enter dcpromo and then click [ OK ].

If Active Directory was previous installed the dcpromo program will find it andwill remove it. Follow the wizard to uninstall it. After Active Directory wasremoved, reboot PC and restart installation of Active Directory again.

3. On the Welcome to the Active Directory Installation Wizard page, click on[ Next ].

4. On the Domain Controller Type page:

Ensure that Domain controller for a new domain is selected.

Click on [ Next ].

5. On the Create Tree or Child Domain page:

Ensure that Create a new domain tree is selected.

Click on [ Next ].

6. On the Create or Join Forest page:

Ensure that Create a new forest of domain trees is selected.

Click on [ Next ].

Complete Installation 1. On the New Domain Name page:

In the Full DNS name for new domain field, enter: . (find it in SPS).

If the Windows 2000 installation is performed for a RNO Server migration the and values can be found in CCL of the migrationmethod.

Click on [ Next ].

2. On the NetBIOS Domain Name page:

Ensure that Domain (where Domain is the assigned domain name)appears.

Click on [ Next ].

3. On the Database and Log Locations page, accept the default locationsby clicking [ Next ] .

4. On the Shared System Volume page, accept the default location by clicking[ Next ] .

5. On the Permissions page:

Select Permissions compatible only with Windows 2000 servers.

3BK 17421 4031 RJZZA Ed.08 41 / 64


Click on [ Next ] .

6. On the Directory Services Restore Mode Administrator Password page:

On the Password and Confirm password boxes enter:In case of RNO machine, type rnoadm.In case of LASER machine, type laseradm.

Click on [ Next ].

7. On the Summary page:

Review the options you selected.

Click on [ Next ].The Active Directory installation process begins.

8. When the Completing the Active Directory Installation Wizard page appears,click on [ Finish ], and then restart your computer by clicking on [ RestartNow ].

Convert Standard

Primary Zones

1. Log in as Administrator.2. Open DNS :

Start -> Programs -> Administrative Tools -> DNS3. In the console tree:

Expand Computer (where Computer is the computer name).Expand Forward Lookup Zones.

Click on . zone.

4. Right click on . zone and select Properties.5. In the . Properties dialog box:

On the General tab, click on [ Change ].6. In the Change Zone Type dialog box:

Select Active Directory - integrated.

Click on [ OK ].

7. In the DNS dialog box, click [ OK ] to confirm the change, and then click[ Ok ] to close . Properties dialog box.

8. Repeat steps 4 to 7 for the Reverse Lookup Zones.9. Close DNS window.

Convert Domain to

Native Mode

1. Select:Start -> Programs -> Administrative Tools -> Active Directory Usersand Computers

2. In the console tree, right click on . and selectProperties.

3. In the . Properties box:Click on [ Change Mode ].

4. In the Active Directory dialog box, click [ Yes ] to confirm the change.5. Click [ OK ] to close the . Properties box.

42 / 64 3BK 17421 4031 RJZZA Ed.08


6. Click [ OK ] to close the Active Directory dialog box.7. Update the Completion Check List (CCL).

4.1.4 Set Time Server1. Open a Command Prompt window:

Start -> Programs -> Accessories -> Command Prompt2. In Command Prompt window enter following command:

C:\> net time /setsntp:where is the IP address of the server. Find value inSPS.

In case of RNO Server migration find address in CCL of the migration method.


4.1.5 Create Users4.1.5.1 Create User for RNO

Perform this paragraph just in case of future RNO Server installation

1. In Active Directory Users and Computers window select ..

2. Perform following action:Action -> New -> User

3. In New Object - User window:Enter rno in Full name field.

Enter rno in User logon name field.

Check that rno is present in User logon name (pre Windows 2000) field.Click on [ Next ].

4. In next window:

Enter rno in Password and Confirm password fields.

Check Password never expires check box.

Click on [ Next ].

5. In next window click on [ Finish ].6. Repeat steps 2 to 4 to create alcatel user with alcatel password.

3BK 17421 4031 RJZZA Ed.08 43 / 64


4.1.5.2 Create User for LASER

Perform this paragraph just in case of future LASER Server installation

1. In Active Directory Users and Computers window select ..

2. Perform following action:Action > New > User

3. In New Object - User window:Enter Laser in Full name field.

Enter Laser in User logon name field.

Check that Laser is present in User logon name (pre Windows 2000)field.

Click on [ Next ].

4. In next window:

Enter Laser in Password and Confirm password fields.

Check Password never expires check box

Click on [ Next ].

5. In next window click on [ Finish ].4.1.5.3 Group Settings

Perform this paragraph for both RNO or LASER Server installation.

1. In Active Directory Users and Computers window expand the.

2. In console tree select Users and after right click on Domain Adminsgroup in right window.On the pop-up menu select Properties.

3. In Domain Admins Properties window:Under Members tab click on [ Add... ].

4. In Select Users, Contacts, Computers, or Groups window:

Select alcatel or Laser user in upper window.

Click on [ Add ].Click on [ OK ].

5. In Domain Admins Properties window:Click on [ OK ] button to close window.

6. Close Active Directory Users and Computers window.7. Update the Completion Check List (CCL).

44 / 64 3BK 17421 4031 RJZZA Ed.08


4.1.6 Check Date/Time1. In Control Panel window double click on Date/Time icon.2. Verify date, time and time zone; if it is needed then modify it.3. Close Date/Time Properties window with click on [ OK ].4. Close Control Panel window.5. Update the Completion Check List (CCL).

4.1.7 Check Regional Options1. In Control Panel window double click on Regional Options icon.2. In Your Locale field select English (United States).3. Select Numbers index.4. In the Decimal symbol field there must be the following character: ".". If

not, enter it.5. In the List separator field there must be the following character: ";". If

not, enter it.6. Then, click on [ OK ].7. Log out from current Administrator session and log on as alcatel or Laser

user

8. Perform steps from 1 to 6 to check regional options for alcatel or Laser user.9. Log out, and log on again as Administrator.


4.1.8 Check Display Properties for Server1. In Control Panel window double click on Display icon.2. Select Settings tab.3. Click on [ Advanced ] :

On Adapter tab verify that adapter and drivers are conform SPS.

On General tab check that the value in Font Size field is Small Fonts.

In Monitor tab for Refresh Frequency, check that it is equal or above 75Hz.If is not the case, change to a frequency equal or greater to 75 Hz.

Click [ OK ] to close the window.If changes was performed, click on [ OK ] button to apply changes andafter confirm with [ Yes ].

4. For Colors field, check that it is greater or equal to 65536.If not change to 65536 (16 bit) or a greater value.

5. For Screen Area field, check that the resolution is 800x600.If is not the case, change to a resolution equal or greater to 800x600.

6. Click [ OK ] to close Display Properties window.If changes was performed, click on [ OK ] to apply changes and confirmwith [ Yes ].

3BK 17421 4031 RJZZA Ed.08 45 / 64



4.1.9 Install TCP/IP Printer

Apply this paragraph for ALL configurations.

1. Select following menu path:Start > Settings > Printers

2. In Printers window:Double click on Add Printer icon.

3. In Welcome to the Add Printer Wizard window:Click on [ Next ].

4. In Local or Network Printer window:

Select Local Printer

Clear Automatically detect my Plug and Play printer

Click on [ Next ].

5. In Select Printer Port window:

Select Create a new port

In Type field select Standard TCP/IP Port.

Click on [ Next ].

Add TCP/IP Printer Port 1. In Welcome to the Add Standard TCP/IP Printer Port Wizard window:Click on [ Next ].

2. In Add Port window:

Enter IP address of the printer in Printer Name or IP Address field.

Click on [ Next ].

3. In Completing the Add Standard TCP/IP Printer Port Wizard window:Click on [ Finish ].Wait until Add Printer Wizard window is displayed.

Add Printer Driver 1. In Add Printer Wizard window:Click on [ Have Disk ].

2. Insert CD or floppy with printer driver.3. In Install From Disk window:

Click on [ Browse ].Select path to the printer driver.

Click on [ OK ].

4. In Name Your Printer window:

In Printer Name field enter the printer name (find it in SPS).

46 / 64 3BK 17421 4031 RJZZA Ed.08


Click on [ Next ].

5. In Printer Sharing window:Click on [ Next ].

6. In Print a Test Page window:

Select Yes.

Click on [ Next ].

7. In Completing the Add Printer Wizard window:Click on [ Next ].If test page was not printed, refer to the documentation of the printer.

Do not continue with RNO or LASER software installation until printer was notinstalled correctly.


4.2 Windows 2000 Professional Customization and Checks

Perform this paragraph on Client or Standalone only.

4.2.1 Customize and Check Network Parameters1. Right click on My Network Places icon.

Select Properties from the pop-up menu.2. In Network and Dial-up Connections window:

Right click on Local Area Connection icon.Select Properties from the pop-up menu.

3. In Local Area Connection Properties window:Click on [ Configure ].

4. In Properties window:

In General tab:Check the network card name. Find network card name in SPS. If isnot correct, install the right one from diskette.

In Driver tab:Check the driver. Find the driver in SPS. If is not correct, install theright one.

Click on [ OK ].



6. In Internet Protocol (TCP/IP) Properties window:

3BK 17421 4031 RJZZA Ed.08 47 / 64


Check if Use the following IP address: is selected. If is not selected,select it.

Check and modify if needed the value for IP Address, Subnet masksand Default gateway. Find this values in SPS.

Check if Use the following DNS server addresses: is selected. If not,select it.

In Preferred DNS server field enter:In case of Standalone: DNS IP address from SPS.In case of Client: the IP address of the Server from SPS.

Click on [ OK ].

7. In Local Area Connections Properties window:Click on [ OK ].

8. Close Network and Dial-up Connections window.9. Update the Completion Check List (CCL).

4.2.2 Connect Clients to Domain

This paragraph is applicable for Clients PC only.

1. Right click on My Computer icon on the desktop.Select Properties.

2. In System Properties window:

Select Network Identification tab.

On Network Identification tab click on [ Properties ].

3. In Identification Changes window:

Select Domain bullet.

Enter domain name.Find domain name in SPS.

Click on [ OK ].

4. In Domain Username And Password window:

Enter Administrator in Name field.

Enter password for domain Administrator (Server Administrator) inPassword field.

Click [ OK ].

5. In Network Identification window:Click on [ OK ] button and in next window click again on [ OK ].

6. In System Properties window:Click on [ OK ].

48 / 64 3BK 17421 4031 RJZZA Ed.08


7. In System Settings Change window:Click on [ Yes ] button to restart computer.


4.2.3 Create Users for RNO

Perform this paragraph only in case of future RNO Standalone.

Create Users 1. Go on the menu path:Start > Settings > Control Panel

2. In Control Panel window, double click on Administrative Tools icon.3. In Administrative Tools window, double click on Computer Management icon.4. In Computer Management window, select Users (double lick on Local Users

and Groupsif the tree is closed).5. In User Manager window, to create a new user:

Action > New User...6. In the New User window:

Enter alcatel as user name and password

Clear option User Must Change Password at Next Logon

Select Password never expires

Click on [ Create ].

7. Repeat the operations described before to create an other user with username: rno and password rno.Close New User window after the rno user was created.

Group Settings 1. In Computer Management window:Right click on alcatel user and select Properties.

2. In alcatel Properties window:Select the Member Of tab.

3. In Member Of tab:Click on [ Add... ].

4. In Select Groups window:

Select Administrators group.


5. In alcatel Properties window:Click on [ OK ].

6. Close Computer Management window.7. Update the Completion Check List (CCL).

3BK 17421 4031 RJZZA Ed.08 49 / 64


4.2.4 Create Users for LASER

Perform this paragraph only in case of future LASER Standalone machines.


2. In Control Panel window, double click on Administrative Tools icon.3. In Administrative Tools window, double click on Computer Management icon.4. In Computer Management window, select Users (double click on Local

Users and Groups if it is closed).5. In Computer Management window, to create a new user, follow the menu

path:Action > New User...

6. In the New User window:

Enter Laser for User name, Password and Confirm password.

Clear option User Must Change Password at Next Logon.

Select Password never expires.

Click on [ Create ].Once the Laser user is created, close the New User window.

Group Settings 1. In Computer Management window:Right click on Laser user and select Properties.

2. In Laser Properties window:Select the Member Of tab.





5. In Laser Properties window:Click on [ OK ].

6. Close Computer Management window.7. Close Administrative Tools window.8. Update the Completion Check List (CCL).

50 / 64 3BK 17421 4031 RJZZA Ed.08


4.2.5 Check Date/TimeTo check the date and time perform following steps:1. Log in as domain Administrator.2. Go on the menu path:

Start -> Settings -> Control Panel3. In Control Panel window, double click on Date/Time icon.4. Verify date, time and time zone; if it is needed then modify it.5. Close Date/Time Properties window with click on [ OK ].6. Close Control Panel window.7. Update the Completion Check List (CCL).

4.2.6 Check Regional Options

Perform this paragraph logged on as Administrator, rno, alcatel for RNOinstallation (migration), or Administrator and Laser in case of LASERinstallation (migration).

1. Go on the menu path:Start -> Settings -> Control Panel

2. In Control Panel window double click on Regional Options icon.3. In Regional Options field select English (United States).4. Select Numbers tab.5. In the Decimal symbol field it must be the following character: ".". If

not, enter it.6. In the List separator field it must be the following character: ";". If

not, enter it.7. Click on [ OK ].8. Log out and log on as other user and repeat steps 1 to 6.9. Update the Completion Check List (CCL).

4.2.7 Check Display Properties for WorkstationTo check the display perform following steps:1. Log in as domain Administrator.2. In Control Panel window double click on Display icon.3. Select Settings tab.4. Click on [ Advanced ] button:

On Adapter tab verify that adapter and drivers are conform SPS. Ifnot, install the right driver.


In Monitor tab for Refresh Frequency, check that it is equal or above 85Hz. If is not the case change to a frequency equal or greater to 85 Hz.

3BK 17421 4031 RJZZA Ed.08 51 / 64


Click [ OK ] button to close the window. Confirm clicking on [ OK ].

5. For Colors field, check that it is greater or equal to 65536 (16 bits). If notchange to 65536 (16 bits) or a greater value.

6. For Screen Area field, check that the resolution is 1280x1024. If is not thecase, change to a resolution equal or greater to 1280x1024.

7. Click [ OK ] to close Display Properties window.Confirm changes, if needed, clicking on [ OK ].



Apply this paragraph for all configurations.

1. Select following menu path:Start -> Settings -> Printers






Click on [ Next ].




Click on [ Next ].




Click on [ Next ].




52 / 64 3BK 17421 4031 RJZZA Ed.08



Click on [ OK ].


In Printer Name field enter the printer name (find it in SPS).Click on [ Next ].



Select Yes.

Click on [ Next ].




3BK 17421 4031 RJZZA Ed.08 53 / 64


4.3 Windows XP Professional Customization and Checks

Perform this paragraph on Client or Standalone only.

4.3.1 Customize and Check Network Parameters1. Open the menu path:

Start -> Settings -> Control PanelDouble click on Network Connection icon.

2. In Network Connections window:Right click on Local Area Connection icon.Select Properties from the pop-up menu.

3. In Local Area Connection Properties window:Click on [ Properties ].

4. In Properties window:

In General tab:Check the network card name. Find network card name in SPS. If isnot correct, install the right one from diskette.

In Driver tab:Check the driver. Find the driver in SPS. If is not correct, install theright one.

Click on [ OK ].



6. In Internet Protocol (TCP/IP) Properties window:Check if Use the following IP address: is selected. If is not selected,select it.

Check and modify if needed the value for IP Address, Subnet masks andDefault gateway. Find these values in SPS.

Check if Use the following DNS server addresses: is selected. If not,select it.

In Preferred DNS server field :In case of Standalone, enter DNS IP address from SPS.In case of Client, enter the IP address of the Server from SPS.

Click on [ OK ].

7. In Local Area Connections Properties window:Click on [ OK ].

8. Close Network Connections window.

54 / 64 3BK 17421 4031 RJZZA Ed.08



4.3.2 Activate Windows XP1. Open the menu path:

Start -> Activate Windows2. In Lets activate Windows window, select Yes, lets activate Windows over

the internet now and click [ Next ].3. In Register with Microsoft window, select No, I dont want to register now;

lets just activate Windows and click [ Next ].4. In Thank You window click on [ OK ].5. Update the Completion Check List (CCL).

4.3.3 Create Users for LASER

Perform this paragraph only in case of future LASER Client machines.


2. In Control Panel window, double click on Administrative Tools icon.3. In Administrative Tools window, double click on Computer Management icon.4. In Computer Management window, select Users (double click on Local

Users and Groups if it is closed).5. In Computer Management window, to create a new user, follow the menu

path:Action > New User...

6. In the New User window:

Enter Laser for User name, Password and Confirm password.

Clear option User Must Change Password at Next Logon.

Select Password never expires.

Click on [ Create ].Once the Laser user is created, close the New User window.

Group Settings 1. In Computer Management window:Right click on Laser user and select Properties.

2. In Laser Properties window:Select the Member Of tab.





3BK 17421 4031 RJZZA Ed.08 55 / 64


5. In Laser Properties window:Click on [ OK ].

6. Close Computer Management window.7. Close Administrative Tools window.8. Update the Completion Check List (CCL).

4.3.4 Check Date and TimeTo check the date and time perform following steps:1. Go on the menu path:

Start > Settings > Control Panel2. In Control Panel window, double click on Date and Time icon.3. Verify date, time and time zone; if it is needed then modify it.4. Close Date/Time Properties window with click on [ OK ].5. Close Control Panel window.6. Update the Completion Check List (CCL).

4.3.5 Check Regional Options

Perform this paragraph logged on as Administrator and Laser in case ofLASER installation (migration).

1. Go on the menu path:Start -> Settings -> Control Panel

2. In Control Panel window double click on Regional an Language Options icon.3. In Regional Options field select English (United States).4. Select Customize.5. In the Decimal symbol field it must be the following character: ".". If

not, enter it.6. In the List separator field it must be the following character: ";". If

not, enter it.7. Click on [ OK ].8. Log out and log on as other user and repeat steps 1 to 6.9. Update the Completion Check List (CCL).

56 / 64 3BK 17421 4031 RJZZA Ed.08


4.3.6 Check Display Properties for WorkstationTo check the display perform following steps:1. Log in as domain Administrator.2. In Control Panel window double click on Display icon.3. Select Settings tab.4. Click on [ Advanced ] button:

On Adapter tab verify that adapter and drivers are conform SPS. Ifnot, install the right driver.


In Monitor tab for Refresh Frequency, check that it is equal or above 85Hz. If is not the case change to a frequency equal or greater to 85 Hz.

Click [ OK ] button to close the window. Confirm clicking on [ OK ].

5. For Color quality field, check that it is greater or equal to 65536 (16 bits). Ifnot change to 65536 (16 bits) or a greater value.

6. For Screen resolution field, check that the resolution is 1280x1024. If is notthe case, change to a resolution equal or greater to 1280x1024.

7. Click [ OK ] to close Display Properties window.Confirm changes, if needed, clicking on [ OK ].



Apply this paragraph for all configurations.

1. Select following menu path:Start > Settings > Printers and Faxes






Click on [ Next ].




Click on [ Next ].

3BK 17421 4031 RJZZA Ed.08 57 / 64





Click on [ Next ].





Click on [ OK ].


In Printer Name field enter the printer name (find it in SPS).Click on [ Next ].



Select Yes.

Click on [ Next ].




58 / 64 3BK 17421 4031 RJZZA Ed.08

5 PI 04: Third Party Software Installation


This chapter describes the operations to be performed for installation of thirdparty software.

3BK 17421 4031 RJZZA Ed.08 59 / 64


5.1 ARCserve 11 Installation

Apply this section as Administrator for Standalone or Server configuration.

Start Installation 1. Insert the ARCserve 11 CD-ROM into CD-ROM drive.2. If the installation program does not run automatically then run setup.exe

from the root directory of ARCserve CD-ROM.

3. In Welcome to the BrightStor ARCserve Release 11 Backup ProductInstallation Browser window, click Install BrightStor ARCserve Backup,agents, options and more.

4. Click Install BrightStor ARCserve Backup, agents, options and more.Wait for the next window.

5. In License Agreement window, scroll down until the end of message window.Click on [ I Agree ].

6. In Customer Information window :

Check the User Name and Organization; if it is not OK then enter theright values.

Click on [ Next ].

7. In the License Key Entry window, type the right license code.Click on [ Next ].

Configure Installation 1. In Select Install Type window :

Select Local Install option.

Click on [ Next ] and wait.

2. In Select Products window :

Click on [ Change Folder ], then type the D:\ARCserve11 for InstallPath field.

Verify that the Base Manager, Base Server, Server Admin and DisasterRecovery Option are selected.

Click on [ Next ].

3. In Select Database window :

Select Standard Database option.

Click on [ Next ].

4. In Set Password window, type and confirm password (by default is admin).Click on [ Next ].

5. In System Account window :

Check the User Name is Administrator.

Check the Domain/Computer name for the right values.

Enter password for Administrator.

60 / 64 3BK 17421 4031 RJZZA Ed.08


Confirm password for Administrator.

Click on [ Next ] .

6. In Account Configuration window, click on [ Skip ].If warning appears click on [ Yes ] then on [ OK ].

Complete Installation 1. In Product List window, click on [ Install ] and wait.2. In Licensing Information window, click on [ Continue ].3. In Components window :

Select BrightStor ARCserve Backup for Windows Disaster RecoveryOption line.

Choose Use License Key option.

Insert the License Key then click on [ Add ].Click on [ Continue ] and wait for some minutes.

4. In Install Summary window, click on [ Next ].5. In Alternate Location for DR Information window:

Clear Use alternate path for added disaster protection option.

Click on [ OK ].

6. In Install Summary window, click on [ Finish ].7. In Registration window, choose Do not ask me again then click on

[ Continue ].8. In BrightStor ARCserve Backup window, click on [ Exit ].9. Restart the computer.


3BK 17421 4031 RJZZA Ed.08 61 / 64


5.2 Microsoft Office 2000 Installation

Apply this paragraph for future RNO/LASER Workstation (Client / Standalone)and for LASER Server.

1. Insert the Microsoft Office 2000 CD-ROM in the CD-ROM drive.2. The Welcome to Microsoft Office 2000 window appears automatically:

It asks for the User name, Initials, Organization, CD-key.

Ask customer representative for the User name, Initials, Organization andfind the CD-key in SPS. Fill the corresponding fields then click [ Next ].

3. Microsoft Office 2000 End-User License Agreement window appears:

Select I accept the terms in the License Agreement bullet.

Click on [ Next ].

4. Microsoft Office 2000: Ready to install window appears:Click on Customize icon.

5. Microsoft Office 2000 Installation Location window appears. It asks forMicrosoft Office 2000 location:

Insert D:\Program Files\Microsoft Office\.

Click on [ Next ].

6. Microsoft Office 2000: Selecting Features window appears:

Click the icon near Microsoft Word and Microsoft Excel and choose Runall from My Computer.

For all other products select Not Available.

Click on [ Install Now ].

7. In Installer Information window appears informing that the installer mustreboot the system before of Microsoft Office 2000 configuration:Click on [ Yes ] to reboot to take effect.

8. After reboot, log in as Administrator. The system displays a FinishingMicrosoft Office 2000 Setup window. A progress bar is moving for sometimes, then the installation is completed.


62 / 64 3BK 17421 4031 RJZZA Ed.08


5.3 Internet Explorer Configuration

This section is optional. To be applied for future RNO/LASER Standaloneor Client.

The following steps configure the Windows 2000 operating system to open alsothe HTM files with Internet Explorer application.1. Open the Windows Explorer.2. In the Windows Explorer window, select Tools > Folder Options3. In the File Types tab, select HTM extension.4. Click on [ Advanced ].5. Select Open line, then click on [ Edit... ].6. Click on [ Browse... ] for the path of the Internet Explorer application:

C:\Program Files\Internet Explorer\iexplorer.exe %17. Clear Use DDE option.8. Click on [ OK ].9. Click on [ Change Icon ].

10. Click on [ Browse... ] for the path of the Internet Explorer application:C:\Program Files\Internet Explorer\ieplorer.exe

11. Choose the icon you want then click on [ OK ].12. In the Edit File Type window, click on [ OK ].13. In the Folder Options window, click on [ Close ].14. Update the Completion Check List (CCL).

3BK 17421 4031 RJZZA Ed.08 63 / 64


BLANK PAGE BREAK

64 / 64 3BK 17421 4031 RJZZA Ed.08