rne fundamentals b11
TRANSCRIPT
Section 1 · Module 1 · Page 1
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
Do not delete this graphic elements in here:
All Rights Reserved © Alcatel-Lucent 2010
Module 1Basics
TMO 18047Issue 01
Section 1Basics
RNERNE (Radio Network Engineering) B11 Fundamentals
TMO54014 Issue 01
Section 1 · Module 1 · Page 2
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 2
Blank Page
This page is left blank intentionally
First editionHille, Helmut2010-01-0701
RemarksAuthorDateEdition
Document History
Section 1 · Module 1 · Page 3
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
Do not delete this graphic elements in here:
All Rights Reserved © Alcatel-Lucent 2010
TMO54014 Edition 1
RNE Fundamentals
Section 1 · Module 1 · Page 4
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 4
Blank Page
This page is left blank intentionally
Section 1 · Module 1 · Page 5
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 5
Objectives
By the end of the course, participants will be able to: - Plan a standard GSM (single band and single layer)
network in urban, suburban and rural areas fulfillingdefined coverage probability;
- Choose suitable BTS site configurations for different clutter types:- Omni sites/sectorized sites,- Number of TRX,- Antenna height and antenna type,- Feeder cable.- Plan site locations:- To achieve planned coverage probability- Inter site distanceAntenna azimuth and tilt.
Section 1 · Module 1 · Page 6
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 6
Table of Contents
Switch to notes view! Page
1 Introduction Standardisation & Documentation 151.1.1 www.3GPP.org organizational partners 161.1.2 TSG Organisation 171.1.3 Specifications and Releases 181.1.4 Specifications out of Release 1999 19
1.2 Radio Network Architecture 201.2.1GSM Network Architecture with out GPRS 211.2.2 GSM Network Architecture with GPRS 221.2.3 OMC-R 231.2.4 GSM Network Elements 241.2.5 RF Spectrum 25
1.3 Mobile Phone Systems 261.3.1 Access Methods 271.3.2 FDMA 281.3.3 TDMA 291.3.4 CDMA (Code Division Multiple Access) 301.3.5 Analogue Cellular Mobile Systems 311.3.6 AMPS (Advanced Mobile Phone System) 321.3.7 AMPS - Technical objectives 331.3.8 AMPS Frequency Range 341.3.9 TACS Total Access Communications System 351.3.10 TACS - Technical objectives 361.3.11 Different TACS-Systems 371.3.12 TACS (Total Access Communications System) 381.3.13 Why digital mobile communication ? 391.3.14 GSM - Technical objectives 401.3.15 DECT (Digital European Cordless Telephone) 411.3.16 DECT - Technical objectives 421.3.17 CDMA - Technical objectives 431.3.18 CDMA - Special Features 441.3.19 CDMA - Technical objectives 451.3.20 TETRA - Features 461.3.21 TETRA - Typical Users 471.3.22 TETRA - Technical objectives 481.3.23 Universal Mobile Telecommunication System 49
1.4 RNP Process Overview 501.4.1 Definition of RN Requirements 511.4.2 Preliminary Network Design 521.4.3 Project Setup and Management 531.4.4 Initial Radio Network Design 541.4.5 Site Acquisition Procedure 551.4.6 Technical Site Survey 561.4.7 Basic Parameter Definition 571.4.8 Cell Design CAE Data Exchange over COF 581.4.9 Turn On Cycle 591.4.10 Site Verification and Drive Test 601.4.11 HW / SW Problem Detection 611.4.12 Basic Network Optimization 621.4.13 Network Acceptance 631.4.14 Further Optimization 64
2 Coverage Planning 652.1 Geo databases 66
2.1.1 Geographical data needed for Radio Network Planning ? 672.1.2 Maps are flat 68
Section 1 · Module 1 · Page 7
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 7
Table of Contents [cont.]
Switch to notes view! Page
2.1.3 Mapping the earth 692.1.4 Map Projection 702.1.5 Geodetic Ellipsoid 712.1.6 Global & Regional Ellipsoids 722.1.7 Geodetic Datum 732.1.8 Different Map Projection’s 742.1.9 Geo-Coordinate System 752.1.10 WGS 84 (World Geodetic System 1984) 762.1.11 Transverse Mercator Projection 77
2.1 Geo databases 2.1.12 Transverse Mercator Projection (e.g. UTM ) 78
2.1.13 Universal Transverse Mercator System 792.1.14 UTM - Definitions 802.1.15 UTM Zones (e.g. Europe) 812.1.16 UTM-System 822.1.17 UTM Zone Numbers 832.1.18 UTM-System: Example "Stuttgart" 842.1.19 Lambert Conformal Conic Projection 852.1.20 Geospatial data for Network Planning 862.1.21Creation of geospatial databases 872.1.22 Parameters of a Map 882.1.23 Raster- and Vectordata 892.1.24 Rasterdata / Grid data 902.1.25 Vectordata 912.1.26 Digital Elevation Model (DEM) 92
2.1 Geo databases 2.1.27 Morphostructure / Land usage / Clutter (1) 93
2.1.28 Morphostructure (2) 942.1.29 Morphoclasses 952.1.30 Morphoclasses (2) 962.1.31Background data (streets, borders etc.) 972.1.32 Orthophoto 982.1.33 Scanned Maps 992.1.34 Buildings 1002.1.35 Buildings (2) 1012.1.36 Traffic density 1022.1.37 Converting one single point (1a) 1032.1.38 Converting one single point (1b) 1042.1.39 Converting one single point (2a) 1052.1.40 Converting one single point (2b) 1062.1.41 Converting a list of points (3a) 1072.1.42 Converting a list of points (3b) 1082.1.43 Converting a list of points (3c) 1092.1.44 Provider for Geospatial data 1102.1.45 Links for more detailed infos 111
Section 1 · Module 1 · Page 8
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 8
Table of Contents [cont.]
Switch to notes view! Page
2.2 Antennas and Cables 1122.2.1.1 The Antenna System 1132.2.1.2 Antenna Theory 1142.2.1.3 Antenna Data 1152.2.1.4 Antenna Pattern and HPBW 1162.2.1.5 EIRP 1172.2.1.6 Linear Antennas 1182.2.1.7 Monopole Antenna Pattern 1192.2.1.8 Panel Antenna with Dipole Array 1202.2.1.9 Dipole Arrangement 1212.2.1.10 Omni Antenna 122
2.2.2 Antenna Parameters 1232.2.2.1 X 65° T6 900MHz 2.5m 1242.2.2.2 X 65° T6 900MHz 1.9m 1252.2.2.3 X 90° T2 900MHz 2.5m 1262.2.2.4 V 65° T0 900MHz 2.0m 1272.2.2.5 V 90° T0 900MHz 2.0m 1282.2.2.4 X 65° T6 1800MHz 1.3m 1292.2.2.5 X 65° T2 1800MHz 1.3m 1302.2.2.6 X 65° T2 1800MHz 1.9m 1312.2.2.7 V 65° T2 1800MHz 1.3m 1322.2.2.8 V 90° T2 1800MHz 1.9m 133
2.2.3 Cable Parameters 1342.2.3.1 7/8" CELLFLEX® Low-Loss Coaxial Cable 1352.2.3.2 1-1/4" CELLFLEX® Coaxial Cable 1362.2.3.3 1-5/8" CELLFLEX® Coaxial Cable 1372.2.3.4 1/2" CELLFLEX® Jumper Cable 138
2.3 Radio Propagation 1392.3.1 Propagation effects 140
2.3.1.1 Reflection 1412.3.1.2 Refraction 1422.3.1.3 Diffraction 1432.3.1.4 Fading 1442.3.1.5 Fading types 1452.3.1.6 Signal Variation due to Fading 1462.3.1.7 Lognormal Fading 147
2.4 Path Loss Prediction 1482.4.1 Free Space Loss 1492.4.2 Fresnel Ellipsoid 1502.4.3 Fresnel Ellipsoid 1512.4.4 Knife Edge Diffraction 1522.4.5 Knife Edge Diffraction Function 1532.4.6 "Final Solution" for Wave Propagation Calculations? 1542.4.7 CCIR Recommendation 1552.4.8 Mobile Radio Propagation 1562.4.9 Terrain Modeling 1572.4.10 Effect of Morphostructure on Propagation Loss 1582.4.11 Okumura-Hata for GSM 900 1592.4.12 CORRECTIONS TO THE HATA FORMULA 1602.4.13 Hata-Okumura for GSM 900 1612.4.14 COST 231 Hata-Okumura GSM 1800 1622.4.15 Alcatel Propagation Model (Standard Propagation Model) 1632.4.16 Alcatel Propagation Model 1642.4.17 Exercise ‘Path Loss’ 165
2.5 Link Budget Calculation 1662.5.1 Maximum Propagation Loss (Downlink) 1672.5.2 Maximum Propagation Loss (Uplink) 1682.5.3 GSM900/1800 Link Budget 1692.5.3 GSM900/1800 Link Budget 1712.5.4 GSM1800 Link Budget 1722.5.5 Additional Losses Overview 173
Section 1 · Module 1 · Page 9
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 9
Table of Contents [cont.]
Switch to notes view! Page
2.6 Coverage Probability 1742.6.1 Indoor propagation aspects 1752.6.2 Indoor propagation: empirical model 1762.6.3 Indoor Penetration 1772.6.4 Body Loss (1) 1782.6.5 Body Loss (2) 1792.6.6 Body Loss (3) 1802.6.7 Interference Margin 1812.6.8 Degradation (no FH) 1822.6.9 Diversity Gain 1832.6.10 Lognormal margin 1842.6.11 Consideration of Signal Statistics (1) 1852.6.12 Consideration of Signal Statistics (2) 186
2.7 Cell Range Calculation 1872.7.1 Calculation of Coverage Radius R 1882.7.2 Coverage Probability 1892.7.3 Coverage Ranges and Hata Correction Factors 1902.7.4 Conventional BTS Configuration 1912.7.5 Coverage Improvement by Antenna Diversity 1922.7.6 Radiation Patterns and Range 1932.7.7 Improvement by Antenna Diversity and Sectorization 1942.7.8 Improvement by Antenna Preamplifier 195
2.8 Antenna Engineering 1962.8.1 Omni Antennas 1972.8.2 Sector Antenna 1982.8.3 Typical Applications 1992.8.4 Antenna Tilt 2002.8.5 Mechanical Downtilt 2012.8.6 Electrical Downtilt 2022.8.7 Combined Downtilt 2032.8.8 Assessment of Required Tilts 2042.8.9 Inter Site Distance in Urban Area 2052.8.10 Downtilt in Urban Area 2062.8.11 Downtilt in Urban Area 2072.8.12 Downtilt in Suburban and Rural Area 2082.8.13 Antenna configurations 2092.8.14 Antenna Configurations for Omni and Sector Sites 2102.8.15 Three Sector Antenna Configuration with AD 2112.8.16 Antenna Engineering Rules 2122.8.17 Distortion of antenna pattern 2132.8.18 Tx-Rx Decoupling (1) 2142.8.19 TX-RX Decoupling (2) 2152.8.20 TX-RX Decoupling (3) 2162.8.21 Space Diversity 2172.8.22 Power Divider 2182.8.23 Power Divider 2192.8.24 Panel Configurations (1) 2202.8.25 Panel Configurations (2) 2212.8.26 Panel Configurations (3) 222
Section 1 · Module 1 · Page 10
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 10
Table of Contents [cont.]
Switch to notes view! Page
2.8 Antenna Engineering 2.8.27 Feeders 223
2.8.28 Feeder Installation Set and Connectors 2242.8.29 Feeder Parameters 2252.8.30 Feeder attenuation (1) 226
2.8 Antenna Engineering 2.8.31 Radiating Cables 227
2.8.32 Components of a radiating cable system 2282.8.33 Comparison of field strength: Radiating cable and standard antenna 2292.8.34 Example of a radiating cable in a tunnel 2302.8.35 Microwave antennas, feeders and accessories 2312.8.36 Parabolic antenna 2322.8.37 High performance antenna 2332.8.38 Horn antennas 2342.8.39 Specific Microwave Antenna Parameters (1) 2352.8.40 Specific Microwave Antenna Parameters (2) 2362.8.41 Data sheet 15 GHz 2372.8.42 Radiation pattern envelope 2382.8.43 Feeders (1) 2392.8.44 Feeders (2) 2402.8.45 Feeders (3) 2412.8.46 Feeders (4) 2422.8.47 Feeders (5) 2432.8.48 Antenna feeder systems (1) 2442.8.49 Antenna feeder systems (2) 2452.8.50 Antenna feeder systems (3) 246
2.9 Alcatel BSS 2472.9.1 Architecture of BTS - Evolium Evolution A9100 2482.9.2 EVOLIUMTM A9100 Base Station (1) 2492.9.3 EVOLIUMTM A9100 Base Station (2) 2502.9.4 EVOLIUMTM A9100 Base Station (3) 2512.9.5 EVOLIUMTM BTS Features 2522.9.7 Generic Configurations for A9100 G4/5 BTS 2582.9.8 Non multi-band configurations 2592.9.9 Multi-band configurations 2602.9.10 Extended cell configurations 2612.9.11 Standard configurations 2622.9.12 TRX Types 2632.9.12 TRX Types 2642.9.13 BTS Output Power 2652.9.14 Feature Power Balancing 2662.9.15 Cell Split Feature 2672.9.19 Cell Split Example: High Power Configuration 2682.9.22 Indoor BTS Rack Layout 2692.9.23 Outdoor MBO1 Evolution and MBO2 Evolution cabinets 2702.9.24 Micro BTS types 2712.9.25 Technical Data 2722.9.26 BSC capacities in terms of boards 2732.9.27 Capacity and dimensioning for E1 links 2742.9.28 Abis and atermux allocation on LIU boards 275
Section 1 · Module 1 · Page 11
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 11
Table of Contents [cont.]
Switch to notes view! Page
2.10 Coveradge Improvement 2762.10.1 Antenna Diversity 277
2.10.1.1 Diversity 2782.10.1.2 Selection Diversity (1) 2792.10.1.3 Selection Diversity (2) 2802.10.1.4 Selection Diversity (3) 2812.10.1.5 Equal Gain Combining (1) 2822.10.1.6 Equal Gain Combining (2) 2832.10.1.7 Maximum Ratio Combining (1) 2842.10.1.8 Maximum Ratio Combining (2) 2852.10.1.9 Comparison of combining methods 2862.10.1.10 Enhanced Diversity Combining (1) 2872.10.1.11 Enhanced Diversity Combining (2) 2882.10.1.12 Tx Diversity 2892.10.1.12 Tx Diversity 2902.10.1.12 Tx Diversity 2912.10.1.12 Tx Diversity 2922.10.1.12 Diversity systems in Mobile Radio Networks 2932.10.1.13 Space Diversity Systems 2942.10.1.14 Space Diversity - General Rules 2952.10.1.15 Achievable Diversity Gain 2962.10.1.16 Polarization Diversity 2972.10.1.17 Principle of Polarization Diversity 2982.10.1.18 Air Combining 2992.10.1.19 Air Combining with Polarization Diversity 3002.10.1.20 Air Combining with Space Diversity 3012.10.1.21 Decoupling of Signal Branches 3022.10.1.22 Cross Polarized or Hor/Ver Antenna? (1) 3032.10.1.23 Cross Polarized or Hor/Ver Antenna? (2) 3042.10.1.24 Conclusion on Antenna Diversity 305
2.10.2 Repeater Systems 3062.10.2.1 Repeater Application 3072.10.2.2 Repeater Block Diagram 3082.10.2.3 Repeater Applications (2) 3092.10.2.4 Repeater Types 3102.10.2.5 Repeater for Tunnel Coverage 3112.10.2.4 Repeater for Indoor coverage 3122.10.2.5 Planning Aspects 3132.10.2.6 Repeater Gain Limitation (1) 3142.10.2.7 Repeater Gain Limitation (2) 3152.10.2.8 Intermodulation Products 3162.10.2.9 Repeater Link Budget 3172.10.2.10 High Power TRXs 3182.10.2.13 3x6 TRXs High Power Configuration 3192.10.2.14 Mixed TRX Configuration 320
3 Traffic & Frequency Planning 3213.1 Traffic Caspacity 322
3.1.1 Telephone System 3233.1.2 Offered Traffic and Traffic Capacity 3243.1.3 Definition of Erlang 3253.1.4 Call Mix and Erlang Calculation 3263.1.5 ERLANG B LAW (2) 3283.1.6 Erlang´s Formula 3293.1.7 Blocking Probability (Erlang B) 3303.1.8 BTS Traffic Capacity (Full Rate) 331
Section 1 · Module 1 · Page 12
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 12
Table of Contents [cont.]
Switch to notes view! Page
3.2 Network Evolution 3323.2.1 Network Evolution - Capacity Approach (1) 3333.2.2 Network Evolution - Capacity Approach (2) 3343.2.3 Network Evolution - Capacity Approach (3) 3353.2.4 Network Evolution - Capacity Approach (4) 336
3.3 Cell Structures 3373.3.1 Cell Structures and Quality 3383.3.2 Cell Re-use Cluster (Omni Sites) (1) 3393.3.2 Cell Re-use Cluster (Omni Sites)(2) 3403.3.4 Cell Re-use Cluster (Sector Site) (1) 3413.3.5 4x3 Cell Re-use Cluster (Sector Site) (2) 3423.3.6 Irregular (Real) Cell Shapes 343
3.4 Frequency Reuse 3443.4.1 GSM Frequency Spectrum 3453.4.2 Impact of limited Frequency Spectrum 3463.4.3 What is frequency reuse? 3473.4.4 RCS and ARCS (1) 3483.4.5 RCS and ARCS (2) 3493.4.6 Reuse Cluster Size (1) 3503.4.7 Reuse Cluster Size (2) 3513.4.8 Reuse Distance 3523.4.9 Frequency Reuse Distance 3533.4.10 Frequency Reuse: Example 354
3.5 Cell Planning 3553.5.1 Cell Planning - Frequency Planning (1) 3563.5.2 Cell Planning - Frequency Planning (2) 3573.5.3 Influencing Factors on Frequency Reuse Distance 3583.5.4 Conclusion 3593.5.5 Examples for different frequency reuses 360
3.6 Interference Probability 3613.6.1 Interference Theory (1) 3623.6.2 Interference Theory (2) 3633.6.3 CPDF - Cumulative Probability Density Function 3643.6.4 Interference Probability dependent on Average Reuse 365
3.7 Carrier Types 3663.7.1 Carrier Types - BCCH carrier 3673.7.2 Carrier Types - TCH carrier 368
3.8 Multiple Reuse Pattern MRP 3693.8.1 Meaning of multiple reuse pattern (1) 3703.8.2 Meaning of multiple reuse pattern (2) 3713.8.3 GSM restrictions 372
3.9 Intermodulation 3733.9.1 Intermodulation problems (1) 3743.9.2 Intermodulation problems (2) 3753.9.3 Intermodulation problems (3) - Summary 3763.9.4 Treating “neighbor” cells 3773.9.5 Where can I find neighbor cells? 378
3.10 Manual Frequency Planning 3793.10.1 Frequency planning (1) 3803.10.2 Frequency planning (2) 3813.10.3 Exercise: Manual frequency planning (1) 3823.10.4 Exercise: Manual frequency planning (2) 3833.10.5 Discussion: Subdivide Frequency Band? 3843.10.6 Hint for creating a future proofed frequency plan 3853.10.7 Implementing a frequency plan 386
Section 1 · Module 1 · Page 13
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 13
Table of Contents [cont.]
Switch to notes view! Page
3.11 BSCI Planning 3873.11.1 BSCI allocation 3883.11.2 BSIC Planning Rules 3893.11.3 Spurious RACH 3903.11.4 Summary 391
3.12 Capacity Enhancement Techniques 3923.12.1 Capacity enhancement by planning 3933.12.2 Capacity enhancement by adding feature 3943.12.3 Capacity enhancement by adding TRX 3953.12.4 Capacity enhancement by adding cells 3963.12.5 Capacity enhancement by adding sites 397
4 Radio Interface 3984.1 GSM Air Interface 399
4.1.1 Radio Resources 4004.1.2 GSM Transmission Principles (1) 4014.1.3 GSM Transmission Principles (2) 4024.1.4 Advantages of Signal Processing 4034.1.5 Signal Processing Chain 404
4.2 Channel Coding 4054.2.1 Speech Coding 4064.2.2 Error Protection 4074.2.3 Interleaving and TDMA Frame Mapping 4084.2.4 Encryption 4094.2.5 Burst Structure 4104.2.4 Synchronisation 4114.2.5 Modulation 4124.2.6 Propagation Environment 4134.2.7 Equalizing 4144.2.8 Definition of Bit Error Rates 4154.2.9 Speech Quality 4164.2.10 Dependence of BER on Noise and Interference 4174.2.13 Frequency Hopping (1) 4184.2.14 Frequency Hopping (2) 4194.2.15 The OSI Reference Model 4204.2.16 GSM Burst Types (1) 4214.2.17 GSM Burst Types (2) 4224.2.18 Logical Channels 4234.2.19 Possible Channel Combinations 4244.2.20 Channel Mapping (1) 4254.2.21 Channel Mapping (2) 4264.2.22 TDMA Frame Structure for TCHs 427
Section 1 · Module 1 · Page 14
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 14
Blank Page
This page is left blank intentionally
Section 1 · Module 1 · Page 15
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 15
Standardisation & Documentation
1 Introduction
Section 1 · Module 1 · Page 16
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 16
1.1 Standardisation & Documentation
1.1 www.3GPP.org organizational partners
Project supported byARIB Association of Radio Industries and Businesses (Japan)CWTS China Wireless Telecommunication Standard groupETSI European Telecommunications Standards InstitutT1 Standards Committee T1 Telecommunication (US)TTA Telecommunications Technology Association (Korea)TTC Telecommunication Technology Committee (Japan)
The Organizational Partners shall determine the general policy and strategy of 3GPP and perform the following tasks:
Approval and maintenance of the 3GPP scopeMaintenance the Partnership Project Description Taking decisions on the creation or cessation of Technical Specification Groups, and approving their scope and terms of referenceApproval of Organizational Partner funding requirementsAllocation of human and financial resources provided by the Organizational Partners to the Project Co-ordination Group
www.3GPP.org organizational partners:
Source: www.3gpp.org
Section 1 · Module 1 · Page 17
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 17
TSG ORGANIZATION
Project Co-ordination Group(PCG)
TSG RANRadio Access Networks
RAN WG1Radio Layer 1 specification
RAN WG2Radio Layer2 &3 spec
RAN WG3UTRAN O&M requirements
RAN WG4Radio &Protocol Aspects
RAN WG5 (ex T1)Mobile TerminalTesting
TSG SAServices & System Aspects
SA WG1Services
SA WG2Architecture
SA WG3Security
SA WG4Codec
SA WG5Telecom Management
TSG CTCore Network & Terminals
CT WG1 (ex CN1)MM/CC/SM (lu)
CT WG3 (ex CN3)Networks Interworking
CT WG4 (ex CN4)MAP/GTP/BCH/SS
CT WG5 (ex CN5)Open Service Access
CT WG6 (ex T3)Card Application Aspects
TSG GERANGSM EDGE
Radio Access Network
GERAN WG1Radio Aspects
GERAN WG2Protocol Aspects
GERAN WG3Terminal TestingGERAN WG3Terminal Testing
1.1 Standardisation & Documentation
1.2 TSG Organisation
Source: www.3gpp.org
Section 1 · Module 1 · Page 18
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 18
1.1 Standardisation & Documentation
1.3 Specifications and Releases
GSM/Edge Releases: http://www.3gpp.org/specs/releases.htmTR 41.103 GSM Phase 2+ Release 5
Freeze date: March - June 2002 TR 41.102 GSM Phase 2+ Release 4
Freeze date: March 2001TR 01.01 Phase 2+ Release 1999
Freeze date: March 2000
For the latest specification status information please go to the 3GPP Specifications database: http://www.3gpp.org/ftp/Information/Databases/Spec_Status/The latest versions of specifications can be found on ftp://ftp.3gpp.org/specs/latest/
TS – Technical SpecificationTR – Technical Report
Section 1 · Module 1 · Page 19
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 19
1.1 Standardisation & Documentation
1.4 Specifications out of Release 1999
TR 01.04 Abbreviations and acronymsTS 03.22 Functions related to Mobile Station (MS) in idle mode and group receive modeTR 03.30 Radio Network Planning AspectsTS 04.04 Layer 1 - General RequirementsTS 04.06 Mobile Station - Base Stations System (MS - BSS) Interface Data Link (DL) Layer SpecificationTS 04.08 Mobile radio interface layer 3 specificationTS 05.05 Radio Transmission and ReceptionTS 05.08 Radio Subsystem Link ControlTS 08.06 Signalling Transport Mechanism Specification for the Base Station System - Mobile Services Switching Centre (BSS-MSC) InterfaceTS 08.08 Mobile-services Switching Centre - Base Station system (MSC-BSS) Interface Layer 3 Specification
Section 1 · Module 1 · Page 20
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 20
1 Intruduction
1.2 Radio Network Architecture
Section 1 · Module 1 · Page 21
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 21
1.2 Radio Network Architecture
1.2.1GSM Network Architecture with out GPRS
HLR GCR AuC
E
B C
D
F
G H
I
Abis
B C D E F G H I
PSTN ISDN
BTS - BSC
MSC-VLR (SM-G)MSC-HLR
HLR-VLR (SM-G)MSC-MSC (SS7 basic) +
MAP MSC-EIR VLR-VLR
HLR-AuC MSC-GCR
MSC-PSTN (SS7 basic) + TUP or ISUP MSC-ISDN
LapD (ISDN type)
GSM Circuit-switching:
(BSSAP = BSSMAP + DTAP)
A BSC - MSC (SS7 basic) + BSSAP
BTS LapDm
(GSM specific) Um MS - BTS
BSC BSC
MSC MSC
BTS
PSTN / ISDN
MS
VLR VLR EIR
AuC
AuC Authentication Center
BTS Base Transceiver Station
BSC Base Station Controller
BSS Base Station System
EIR Equipment Identity Register
HLR Home Location Register
ISDN Integrated Services Digital Network
MS Mobile Station
OMC-R Operation and Maintenance Centre – Radio
PSTN Public Switched Telephone Network
VLR Visitor Location Register
GCR Group Call Register -The general architecture of GSM is maintained. In addition, a network function is required which is used for registration of the broadcast call attributes, the Group Call Register.
Section 1 · Module 1 · Page 22
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 22
Gc GGSN-HLR IP/SS7
LAPDm(GSM specific)
Gs
Gb
Um (Radio)
Gi GGSN-Data Network IP
MS
BSS - SGSN
Gr SS7SGSN-HLR
Gf SS7SGSN-EIRSGSN-MSC/VLR
GnSGSN-GGSN IP
IPSGSN-SGSN
MS - BTS
Gs
GfGr
Gn
Gn
Gc SS7
GSM Packet-switching (GPRS/EDGE):
BSSGP
BSS withPCU
BSS withPCU
HLR EIR
DataNetwork
SGSN
GGSN
SGSN MSC
1.2 Radio Network Architecture
1.2.2 GSM Network Architecture with GPRS
Note: according to GSM 03.60, the PCU function (Packet Control Unit) may be implemented on the BTS, the BSC or the SGSN site.
MFS Multi – BSS Fast Packet Server A935
PSTN Public Switched Telephone Network
SGSN Serving GPRS Support Node
GGSN Gateway GPRS Support Node
VLR Visitor Location Register
Section 1 · Module 1 · Page 23
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 23
1.2 Radio Network Architecture
1.2.3 OMC-R
BSS
BTS
BTS
Alcatel9135 MFS SSP
+ RCPBSC
SGSN
OMC-R
MS
A bis A ter
TC
Gb
A
GGSNGn
OMC-G
NSS
GPRS CN
GPRS Core Network (CN): Alcatel 1000 GPRS
Packet Control Unit (PCU) function for several BSS: Alcatel 9135 MFS
TC Transcoder
Section 1 · Module 1 · Page 24
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 24
1.2 Radio Network Architecture
1.2.4 GSM Network Elements
Base Station System BSSBase Transceiver Station BTSBase Station Controller BSC
Terminal EquipmentMobile Station MS
Operation and Maintenance Center-Radio OMC-R
Network Subsystem NSS Mobile Services Switching Center MSCVisitor Location Register VLRHome Location Register HLRAuthentication Center AuCEquipment Identity Register EIR
Operation and Maintenance Center OMCMulti-BSS Fast Packet Server (GPRS) MFSServing GPRS Support Node SGSNGateway GPRS Support Node GGSN
Section 1 · Module 1 · Page 25
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 25
1.2 Radio Network Architecture
1.2.5 RF Spectrum
System Total Bandwidth Uplink frequency band /MHz
Downlink frequency band /MHz
Carrier Spacing
GSM 450 2x7.5MHz 450.4-457.6 460.4-467.6 200 kHz
GSM 480 2x7.2MHz 478.8-486 488.8-496 200 kHz
GSM 850 2x25MHz 824-849 869-894 200 kHz
GSM 900 2x25MHz 890-915 935-960 200 kHz
E-GSM 2x35MHz 880-915 925-960 200 kHz
DCS 1800 (GSM)
2x75MHz 1710-1785 1805-1880 200 kHz
PCS 1900 (GSM)
2x60MHz 1850-1910 1930-1990 200 kHz
AMPS : UK
TACS : UK
DECT: Cordless
CDMA: System of next Generation
TETRA: Digital communication System for Commercial use
Frequency Ranges depends on country.
Section 1 · Module 1 · Page 26
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 26
1 Intruduction
1.3 Mobile Phone Systems
Section 1 · Module 1 · Page 27
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 27
1.3 Mobile Phone Systems Access Methods
1.3.1 Access Methods
FDMA
TDMA
CDMA
time
time
time
pow
er
pow
er
pow
er
frequency
frequency
frequency
Section 1 · Module 1 · Page 28
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 28
1.3 Mobile Phone Systems Access Methods
1.3.2 FDMA
Used for standard analog cellular mobile systems(AMPS, TACS, NMT etc.) Each user is assigned a discrete slice of the RF spectrumPermits only one user per channel since it allows the user to use the channel 100% of the time.
Section 1 · Module 1 · Page 29
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 29
1.3 Mobile Phone Systems Access Methods
1.3.3 TDMA
Multiple users share RF carrier on a time slot basisCarriers are sub-divided into timeslotsInformation flow is not continuous for an user, it is sent and received in "bursts"
Section 1 · Module 1 · Page 30
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 30
1.3 Mobile Phone Systems Access Methods
1.3.4 CDMA (Code Division Multiple Access)
Multiple access spread spectrum techniqueEach user is assigned a sequence code during a callNo time division; all users use the entire carrier
What is CDMA ?
One of the most important concepts to any cellular telephone system is that of "multiple access", meaning that multiple,
simultaneous users can be supported. In other words, a large number of users share a common pool of radio channels and
any user can gain access to any channel (each user is not always assigned to the same channel). A channel can be thought
of as merely a portion of the limited radio resource which is temporary allocated for a specific purpose, such as
someone's phone call. A multiple access method is a definition of how the radio spectrum is divided into channels and
how channels are allocated to the many users of the system.
Section 1 · Module 1 · Page 31
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 31
1.3 Mobile Phone Systems Access Methods
1.3.5 Analogue Cellular Mobile Systems
Analogue transmission of speechOne TCH/ChannelOnly FDMA (Frequency Division Multiple Access)Different Systems
AMPS (Countries: USA)TACS (UK, I, A, E, ...)NMT (SF, S, DK, N, ...)...
NMT: Nordic Mobile Telephone System. Allianz von Nordischen Systembetreibern.
AMPS: Advanced Mobile Phone System
TACS: Total Access Communications System
UK United Kingdom
I Italy
A Austria
E Spain
SF Finnland
S Schweden
DK Denmark
N Norwegen
Section 1 · Module 1 · Page 32
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 32
1.3 Mobile Phone Systems Access Methods
1.3.6 AMPS (Advanced Mobile Phone System)
Analogue cellular mobile telephone systemPredominant cellular system operating in the USOriginal system: 666 channels (624 voice and 42 control channels)EAMPS - Extended AMPS Current system: 832 channels (790 voice, 42 control); has replaced AMPS as the US standard NAMPS - Narrowband AMPS New system that has three times more voice channels than EAMPS with no loss of signal quality Backward compatible: if the infrastructure is designed properly, older phones work on the newer systems
Section 1 · Module 1 · Page 33
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 33
1.3 Mobile Phone Systems Access Methods
1.3.7 AMPS - Technical objectives
Technology FDMARF frequency band 825 - 890 MHzChannel Spacing 30 kHzCarriers 666 (832)Timeslots 1Mobile Power 0.6 - 4 WTransmission Voice, (data)HO possibleRoaming possible
Section 1 · Module 1 · Page 34
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 34
1.3 Mobile Phone Systems Access Methods
1.3.8 AMPS Frequency Range
991 1023 1 666 667 799
Extended AMPS
AMPSUplink
Channel number
Frequency of Channel(MHz)
824.040 825.030 844.980
845.010
845.010
Duplex distance45 MHz
Downlink
Channel number
Frequency of Channel(MHz)
991 1023 1 666 667 799
Extended AMPS
AMPS
869.040 870.030 889.980 893.980
890.010
Section 1 · Module 1 · Page 35
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 35
1.3 Mobile Phone Systems Access Methods
1.3.9 TACS Total Access Communications System
Analogue cellular mobile telephone systemThe UK TACS system was based on the US AMPS system TACS - Original UK system that has either 600 or 1000 channels (558 or958 voice channels, 42 control channels)RF frequency band: 890 - 960Uplink: 890-915 Downlink: 935-960Channel spacing: 25 KHz
Section 1 · Module 1 · Page 36
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 36
1.3 Mobile Phone Systems Access Methods
1.3.10 TACS - Technical objectives
Technology FDMARF frequency band 890 - 960 MHzChannel Spacing 25 kHzCarriers 1000Timeslots 1Mobile Power 0.6 - 10 WTransmission Voice , (data)HO possibleRoaming possible
Tacs disturb GSM because the same frequency- range!
Section 1 · Module 1 · Page 37
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 37
1.3 Mobile Phone Systems Access Methods
1.3.11 Different TACS-Systems
ETACS - Extended TACS Current UK system that has 1320 channels (1278 voice, 42 control)and has replaced TACS as the UK standard
ITACS and IETACS - International (E)TACS Minor variation of TACS to allow operation outside of the UK by allowing flexibility in assigning the control channels
JTACS - Japanese TACS A version of TACS designed for operation in Japan
NTACS - Narrowband TACS New system that has three times as many voice channels as ETACS with no loss of signal quality
Section 1 · Module 1 · Page 38
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 38
1.3 Mobile Phone Systems Access Methods
1.3.12 TACS (Total Access Communications System)
1329 2047 0 23 44 323
344
600
100011
890.0125(935.0125
)
905(950
)
915(960
)
1st Assignment in the UK (600 channels)
Organisation B
Organisation A
Original concept (1000 channels)
890935
889.9875(934.9875
)
889.9625(934.9625
)
872.0125(917.0125
)
872917
Frequency of channel
[Mhz]
Number of Channel
E-TACS - 1320 Channels
Borders of channels
[Mhz]
Mobile Station TX
(Base Station TX)
Section 1 · Module 1 · Page 39
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 39
1.3 Mobile Phone Systems Access Methods
1.3.13 Why digital mobile communication ?
Easy adaptation to digital networks
Digital signaling serves for flexible adaptation to operational needs
Possibility to realize a wide spectrum of non-voice services
Digital transmission allows for high cellular implementation flexibility
Digital signal processing gain results in high interference immunity
Privacy of radio transmission ensured by digital voice coding and encryption
Cost and performance trends of modern microelectronics arein favour of a digital solution
Section 1 · Module 1 · Page 40
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 40
1.3 Mobile Phone Systems Access Methods
1.3.14 GSM - Technical objectives
Technology TDMA/FDMARF frequency band 890 - 960 MHzChannel Spacing 200 kHzCarriers 124Timeslots 8Mobile Power (average/max) 2 W/ 8 WBTS Power class 10 ... 40 WMS sensitivity - 102 dBmBTS sensitivity - 104 dBmTransmission Voice, dataHO possibleRoaming possible
Section 1 · Module 1 · Page 41
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 41
1.3 Mobile Phone Systems Access Methods
1.3.15 DECT (Digital European Cordless Telephone)
European Standard for Cordless CommunicationUsing TDMA-SystemTraditional Applications
Domestic use ("Cordless telephone")Cordless office applications
Combination possible withISDNGSM
High flexibility for different applications
Section 1 · Module 1 · Page 42
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 42
1.3 Mobile Phone Systems Access Methods
1.3.16 DECT - Technical objectives
Technology TDMA/FDMARF frequency band 1880 - 1900 MHzChannel Spacing 1.728 MHzCarriers 10Timeslots 12 (duplex)Mobile Power (average/max) 10 mW/250 mWBTS Power class 250 mWMS sensitivity -83 dBmBTS sensitivity -83 dBmTransmission Voice, dataHO possible
Frequency Range with 10 carriers, 1728 KHz channel spacing
10 carrier 24 timeslots
120 Duplex channels
cell radius 200-300 meter
no Equalizer
HO und Macro Diversity Optional
Section 1 · Module 1 · Page 43
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 43
1.3 Mobile Phone Systems Access Methods
1.3.17 CDMA - Technical objectives
Spread spectrum technology(Code Division Multiple Access)Several users occupy continuously one CDMA channel(bandwidth: 1.25 MHz) The CDMA channel can be re-used in every cellEach user is addressed by
A specific code andSelected by correlation processing
Orthogonal codes provides optimumisolation between users
Section 1 · Module 1 · Page 44
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
Vocoder:
8Kbps oder 13 Kbps.
Multiple Forms of diversity:
Frequency diversity (Spektrum 1.25 MHz)
Spatial diversity (2 different receiving Antennas)
Path diversity (Usage of Multi-path propagation)
Time diversity (Interleaving, error correction codes….)
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 44
1.3 Mobile Phone Systems Access Methods
1.3.18 CDMA - Special Features
Vocoder allows variable data ratesSoft handoverOpen and closed loop power controlMultiple forms of diversityData, fax and short message services possible
Section 1 · Module 1 · Page 45
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 45
1.3 Mobile Phone Systems Access Methods
1.3.19 CDMA - Technical objectives
Technology CDMARF frequency band 869-894 / 824-849
or 1900 MHzChannel Spacing 1250 kHzChannels per 1250 kHz 64Mobile Power (average/max) 1-6.3 W / 6.3 WTransmission Voice, dataHO ("Soft handoff") possibleRoaming possible
Section 1 · Module 1 · Page 46
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 46
1.3 Mobile Phone Systems Access Methods
1.3.20 TETRA - Features
Standard for a frequency efficient european digital trunked radio communication system (defined in 1990)Possibility of connections with simultaneous transmission of voice and dataEncryption at two levels:
Basic level which uses the air interface encryptionEnd-to-end encryption (specifically intended for public safety users)
Open channel operation"Direct Mode" possible
Communication between two MS without connecting via a BTSMS can be used as a repeater
Section 1 · Module 1 · Page 47
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 47
1.3 Mobile Phone Systems Access Methods
1.3.21 TETRA - Typical Users
Public safety
Police (State, Custom, Military, Traffic)
Fire brigades
Ambulance service
...
Railway, transport and distribution companies
For use in:
Police, ambulance and fire ServicesSecurity ServicesMilitaryTransport ServicesClosed User Groups (CUGs)Factory site services
Section 1 · Module 1 · Page 48
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 48
1.3 Mobile Phone Systems Access Methods
1.3.22 TETRA - Technical objectives
Technology TDMA/FDMARF frequency band 380 - 400 MHzChannel Spacing 25 or 12.5 KHzCarriers not yet specifiedTimeslots 4Mobile Power (3 Classes) 1, 3, 10 WBTS Power class 0.6 - 25 WMS sensitivity -103 dBmBTS sensitivity -106 dBmTransmission Voice, data, images,
short messageHO possibleRoaming possible
Section 1 · Module 1 · Page 49
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 49
1.3 Mobile Phone Systems Access Methods
1.3.23 Universal Mobile Telecommunication System
Third generation mobile communication system
Combining existing mobile services (GSM, CDMA etc.) and fixed telecommunications services
More capacity and bandwidth
More services (Speech, Video, Audio, Multimedia etc.)
Worldwide roaming
"High" subscriber capacity
http://www.vtt.fi/
Section 1 · Module 1 · Page 50
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 50
1 Intruduction
1.4 RNP Process Overview
Section 1 · Module 1 · Page 51
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 51
1.4 RNP Process Overview
1.4.1 Definition of RN Requirements
The Request for Quotation (RfQ) from the customer prescribes the requirements mainlyCoverage
Definition of coverage probabilityPercentage of measurements above level threshold
Definition of covered areaTraffic
Definition of Erlang per square kilometerDefinition of number of TRX in a cellMixture of circuit switched and packed switched traffic
QoSCall success rateRxQual, voice quality, throughput rates, ping time
Section 1 · Module 1 · Page 52
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 52
1.4 RNP Process Overview
1.4.2 Preliminary Network Design
The preliminary design lays the foundation to create the Bill of Quantity (BoQ)
List of needed network elements Geo data procurement
Digital Elevation Model DEM/Topographic mapClutter map
Definition of standard equipment configurations dependent on
clutter typetraffic density
Coverage PlotsExpected receiving level
Definition of roll out phasesAreas to be coveredNumber of sites to be installedDate, when the roll out takes place.
Network architecture designPlanning of BSC and MSC locations and their links
Frequency spectrum from license conditions
Section 1 · Module 1 · Page 53
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 53
1.4 RNP Process Overview
1.4.3 Project Setup and Management
This phase includes all tasks to be performed before the on site part of the RNP process takes place.This ramp up phase includes:
Geo data procurement if requiredSetting up ‘general rules’ of the projectDefine and agree on reporting scheme to be used
Coordination of information exchange between the different teams which are involved in the project
Each department/team has to prepare its part of the projectDefinition of required manpower and budgetSelection of project database (MatrixX)
Section 1 · Module 1 · Page 54
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 54
1.4 RNP Process Overview
1.4.4 Initial Radio Network Design
Area surveysAs well check of correctness of geo data
Frequency spectrum partitioning designRNP tool calibration
For the different morpho classes:Performing of drive measurementsCalibration of correction factor and standard deviation by comparison of measurements to predicted received power values of the tool
Definition of search areas (SAM – Search Area Map)A team searches for site locations in the defined areasThe search team should be able to speak the national language
Selection of number of sectors/TRX per site together with project management and customerGet ‘real’ design acceptance from customer based on coverage prediction and predefined design level thresholds
Section 1 · Module 1 · Page 55
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 55
1.4 RNP Process Overview
1.4.5 Site Acquisition Procedure
Delivery of site candidatesSeveral site candidates shall be the result out of the site location search
Find alternative sitesIf no site candidate or no satisfactory candidate can be found in the search areaDefinition of new SAM (Search Area Map)Possibly adaptation of radio network design
Check and correct SAR (Site Acquisition Report)
Location informationLand usageObject (roof top, pylon, grassland) informationSite plan
Site candidate acceptance and ranking
If the reported site is accepted as candidate, then it is ranked according to its quality in terms of
Radio transmissionHigh visibility on covered areaNo obstacles in the near field of the
antennasNo interference from other
systems/antennasInstallation costs
Installation possibilitiesPower supplyWind and heat
Maintenance costsAccessibilityRental rates for objectDurability of object
Section 1 · Module 1 · Page 56
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 56
1.4 RNP Process Overview
1.4.6 Technical Site Survey
Agree on an equipment installation solution satisfying the needs of
RNE Radio Network EngineerTransmission plannerSite engineerSite owner
The Technical Site Survey Report (TSSR) defines
Antenna type, position, bearing/orientation and tiltMast/pole or wall mounting position of antennasEMC rules are taken into account
Radio network engineer and transmission planner check electro magnetic compatibility (EMC) with other installed devices
BTS/Node B locationPower and feeder cable mountTransmission equipment installationFinal Line Of Site (LOS) confirmation for microwave link planning
E.g. red balloon of around half a meter diameter marks target location
If the site is not acceptable or the owner disagrees with all suggested solutions
The site will be rejectedSite acquisition team has to organize a new date with the next site from the ranking list
Section 1 · Module 1 · Page 57
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 57
1.4 RNP Process Overview
1.4.7 Basic Parameter Definition
After installation of equipment the basic parameter settings are used for
CommissioningFunctional test of BTS and VSWR check
Call testsRNEs define cell design dataOperations field service generates the
basic software using the cell design CAE data
Cell design CAE data to be defined for all cells are for example:
CI/LAC/BSICFrequenciesNeighborhood/cell handover relationshipTransmit powerCell type (macro, micro, umbrella, …)
Section 1 · Module 1 · Page 58
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 58
1.4 RNP Process Overview
1.4.8 Cell Design CAE Data Exchange over COF
A9156 RNO
OMC 1
COF
ACIE
ACIE
POLOBSS Software offline production
3rd Party RNP or Database
A9155 V6
RNP
A9155PRC Generator
Module
ConversionOMC 2
ACIE = PRC file
ACIE ASCII Configuration Import Export PRC Provisioning Radio Configuration
SC Supervised Configuration
COF CMA Offsite
CMA Customer Management Application
CAE Customer Application Engineering
Section 1 · Module 1 · Page 59
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 59
1.4 RNP Process Overview
1.4.9 Turn On Cycle
The network is launched step by step during the TOCA single step takes typically two or three weeks
Not to mix up with rollout phases, which take months or even yearsFor each step the RNE has to define ‘TOC Parameter’
Cells to go on airDetermination of frequency planCell design CAE parameter
Each step is finished with the ‘Turn On Cycle Activation’Upload PRC/ACIE files into OMC-RUnlock sites
Section 1 · Module 1 · Page 60
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 60
1.4 RNP Process Overview
1.4.10 Site Verification and Drive Test
RNE performs drive measurement to compare the real coverage withthe predicted coverage of the cells.If coverage holes or areas of high interference are detected
Adjust the antenna tilt and orientationVerification of cell design CAE dataTo fulfill heavy acceptance test requirements, it is absolutely essential to perform such a drive measurement.Basic site and area optimization reduces the probability to haveunforeseen mysterious network behavior afterwards.
Section 1 · Module 1 · Page 61
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 61
1.4 RNP Process Overview
1.4.11 HW / SW Problem Detection
Problems can be detected due to drive tests or equipment monitoringDefective equipment
will trigger replacement by operation field serviceSoftware bugsIncorrect parameter settings
are corrected by using the OMC or in the next TOCFaulty antenna installation
Wrong coverage footprints of the site will trigger antenna re-alignments
If the problem is seriousLock BTSDetailed error detectionGet rid of the faultEventually adjusting antenna tilt and orientation
Section 1 · Module 1 · Page 62
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 62
1.4 RNP Process Overview
1.4.12 Basic Network Optimization
Network wide drive measurementsIt is highly recommended to perform network wide drive tests before doing the commercial opening of the networkKey performance indicators (KPI) are determinedThe results out of the drive tests are used for basic optimization of the network
Basic optimizationAll optimization tasks are still site relatedAlignment of antenna systemAdding new sites in case of too large coverage holesParameter optimization
No traffic yet -> not all parameters can be optimized
Basic optimization during commercial serviceIf only a small number of new sites are going on air the basic optimization will be included in the site verification procedure
Section 1 · Module 1 · Page 63
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 63
1.4 RNP Process Overview
1.4.13 Network Acceptance
Acceptance drive testCalculation of KPI according to acceptance requirements in contractPresentation of KPI to the customerComparison of key performance indicators with the acceptance targets in the contractThe customer accepts
the whole networkonly parts of it step by step
Now the network is ready for commercial launch
Section 1 · Module 1 · Page 64
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 64
1.4 RNP Process Overview
1.4.14 Further Optimization
Network is in commercial operationNetwork optimization can be performedSignificant traffic allows to use OMC based statistics by using A9156 RNO and A9185 NPAEnd of optimization depends on contract and mutual agreement between Alcatel and customer
Usually, Alcatel is only involved during the first optimization activities directly after opening the network commercially
Section 1 · Module 1 · Page 65
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 65
2 Coverage Planning
Section 1 · Module 1 · Page 66
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 66
2 Coverage Planning
2.1 Geo databases
Section 1 · Module 1 · Page 67
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 67
2.1 Geo databases
2.1.1 Geographical data needed for Radio Network Planning ?
Propagation models dependon geographical data
Geographical information for site acquisitionLatitude (East/West) / Longitude (North/South) Rectangular coordinates(e.g. UTM coordinates)
Section 1 · Module 1 · Page 68
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 68
2.1 Geo databases
2.1.2 Maps are flat
Longitude
Latitude
x, y
Problem: Earth is 3D, the maps are 2D
Section 1 · Module 1 · Page 69
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 69
2.1 Geo databases
2.1.3 Mapping the earth
The Earth is a very complex shapeTo map the geography of the earth, a reference model (-> Geodetic Datum) is neededThe model needs to be simple so that it is easy to useIt needs to include a Coordinate system which allows the positions of objects to be uniquely identifiedIt needs to be readily associated with the physical world so that its use is intuitive
Section 1 · Module 1 · Page 70
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 70
2.1 Geo databases
2.1.4 Map Projection
Geodetic Datume.g. WGS84, ED50
Ellipsoide.g. WGS84,
International 1924
GeocoordinateSystem
e.g. UTM
Map Projectione.g. Transverse Mercator (UTM),
Lambert Conformal Conic
Section 1 · Module 1 · Page 71
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 71
2.1 Geo databases
2.1.5 Geodetic Ellipsoid
Definition: A mathematical surface (an ellipse rotated around the earth's polar axis) which provides a convenient model of the size and shape of the earth. The ellipsoid is chosen to best meet the needs of a particular map datum system design.
Reference ellipsoids are usually defined by semi-major (equatorial radius) and flattening (the relationship between equatorial and polar radii).
Section 1 · Module 1 · Page 72
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 72
2.1 Geo databases
2.1.6 Global & Regional Ellipsoids
Global ellipsoidse.g. WGS84, GRS80
Center of ellipsoid is“Center of gravity”
Worldwide consistence ofall maps around the world
Regional ellipsoidse.g. Bessel, Clarke, Hayford, Krassovsky
Best fitting ellipsoid for a part of the world(“local optimized”)
Less local deviation
Section 1 · Module 1 · Page 73
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 73
2.1 Geo databases
2.1.7 Geodetic Datum
A Geodetic Datum is a Reference System which includes:
A local or global EllipsoidOne “Fixpoint”
Attention: Referencing geodetic coordinates to the wrong map datum can result in positionerrors ofhundreds of meters
Info:In most cases the shift, rotation and scale factor of a Map Datum is relative to the “satellite map datum” WGS84.
Section 1 · Module 1 · Page 74
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 74
2.1 Geo databases
2.1.8 Different Map Projection’s
Cylindricale.g. UTM, Gauss-Krueger
Conicale.g.Lambert Conformal Conic
Planar/Azimuthal
Info: In 90% of the cases we will have a cylindrical projection in 10% of the cases a conical projection
Section 1 · Module 1 · Page 75
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 75
2.1 Geo databases
2.1.9 Geo-Coordinate System
To simplify the use of maps aCartesian Coordinates is used To avoid negative values a
False Easting value and aFalse Northing valueis added
Also a scaling factor is used to minimize the “projection error”over the whole area
X = EastingY = Northing
Section 1 · Module 1 · Page 76
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 76
2.1 Geo databases
2.1.10 WGS 84 (World Geodetic System 1984)
Most needed Geodetic Datumin the world today (“Satellite Datum”)It is the reference frame usedby the U.S. Department of Defenseis defined by the National Imageryand Mapping Agency (NIMA)The Global Positioning System (GPS)system is based on the World GeodeticSystem 1984 (WGS-84).Optimal adaption to the surface of the earth
Section 1 · Module 1 · Page 77
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 77
2.1 Geo databases
2.1.11 Transverse Mercator Projection
Projection cylinder is rotated 90 degrees from the polar axis (“transverse”)Geometric basisfor the UTMand theGauss-KruegerMap ProjectionConformalMap projection
Section 1 · Module 1 · Page 78
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 78
2.1 Geo databases
2.1.12 Transverse Mercator Projection (e.g. UTM )
Middle-Meridian
Section 1 · Module 1 · Page 79
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 79
2.1 Geo databases
2.1.13 Universal Transverse Mercator System
60 zones, each 6o (60 · 6o = 360o )±3o around each center meridianBeginning at 180o longitude(measured eastward fromGreenwich)
Zone number = (center meridian + 183o ) / 6o
Section 1 · Module 1 · Page 80
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 80
2.1 Geo databases
2.1.14 UTM - Definitions
False Easting: 500 000 m(Middle-meridian x = 500 000 m)
False Northing:Northern Hemisphere: 0 m Southern Hemisphere: 10 000 000 m
Scaling Factor: 0,9996(used to minimize the“projection error” over the whole area)
Section 1 · Module 1 · Page 81
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 81
2.1 Geo databases
2.1.15 UTM Zones (e.g. Europe)
UTM-Zones
9° 15° 21° 27° 33° 39°3°-3°-6° Middle-Meridian
Section 1 · Module 1 · Page 82
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 82
UTM-System
False origin on the central meridian of the zone has an easting of 500,000 meters.
All eastings have a positive values for the zone
Eastings range from 100,000 to 900,000 meters
The 6 Degree zone ranges from 166,667 to 833,333 m, leaving about a 0.5° overlap at each end of the zone(valid only at the equator)
This allows for overlaps and matching between zones
2.1 Geo databases
2.1.16 UTM-System
Section 1 · Module 1 · Page 83
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 83
2.1 Geo databases
2.1.17 UTM Zone Numbers
Section 1 · Module 1 · Page 84
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 84
UTM-Zone: 32
Middle meridian: 9o
(9o = 500 000 m“False Easting”)
2.1 Geo databases
2.1.18 UTM-System: Example "Stuttgart"
Transformation: latitude / longitude → UTM system
North 48o 45' 13.5''
East 9o 11' 7.5''
y = 5 400 099 m
x = 513 629 m
Section 1 · Module 1 · Page 85
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 85
2.1 Geo databases
2.1.19 Lambert Conformal Conic Projection
Maps an ellipsoid onto a cone whose central axis coincides with the polar axis
Cone touches the ellipsoid=> One standard parallel (1SP)(e.g. NTF-System in France)
Cutting edges of cone and ellipsoid=> Two standard parallels (2SP)(e.g. Lambert-Projection in Austria)
Section 1 · Module 1 · Page 86
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 86
2.1 Geo databases
2.1.20 Geospatial data for Network Planning
DEM (Digital Elevation Model)/ TopographyMorphostructure / Land usage / ClutterSatellite Photos /Orthoimages Scanned MapsBackground data(streets, borders,coastlines, etc. )
BuildingsTraffic data
Section 1 · Module 1 · Page 87
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 87
2.1 Geo databases
2.1.21Creation of geospatial databases
Satellite imagery Digitizing maps Aerial photography
Geospatial data
Section 1 · Module 1 · Page 88
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 88
2.1 Geo databases
2.1.22 Parameters of a Map
Coordinate systemMap Projection(incl. Geodetic Datum)Location of the map (Area …)Scale:
macrocell planning1:50000 - 1:100000microcell planning1:500 -1:5000
ThematicSourceDate of Production
Section 1 · Module 1 · Page 89
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 89
Raster dataDEM /TopographyMorphostructure /Land usage / ClutterTraffic density
Vector dataBackground data(streets, borders, coastlines, etc. )Buildings
2.1 Geo databases
2.1.23 Raster- and Vectordata
x
y
(x1,y1)
(xn,yn)
Section 1 · Module 1 · Page 90
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 90
2.1 Geo databases
2.1.24 Rasterdata / Grid data
Pixel-oriented dataStored as row and column Each Pixel stored in one or two byteEach Pixel contents information(e.g. morphoclass,colour of a scanned map, elevation of a DEM)
Section 1 · Module 1 · Page 91
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 91
2.1 Geo databases
2.1.25 Vectordata
Vector mainly used are: airport, coastline, highway, main roads, secondary roads, railway, rivers/lakesEach vector contents
Info about kind of vector(e.g. street, coastline)A series of several pointsEach point has a corresponded x / y -value(e.g. in UTM System or as Long/Lat)Info about Map projection and used Geodetic Datum
(x1,y1)
(xn,yn)
Section 1 · Module 1 · Page 92
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 92
2.1 Geo databases
2.1.26 Digital Elevation Model (DEM)
Raster dataset that showsterrain features such as hillsand valleysEach element (or pixel) inthe DEM image represents the terrain elevation at that locationResolution in most cases: 20 m for urban areas50-100 m for other areasDEM are typically generatedfrom topographic maps,stereo satellite images,or stereo aerial photographs
Section 1 · Module 1 · Page 93
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 93
2.1 Geo databases
2.1.27 Morphostructure / Land usage / Clutter (1)
Land usage classificationaccording to the impact on wave propagationIn most cases:7...14 morpho classesResolution in most cases:20 m for cities50…100m other areasfor radio networkplanning
The clutter files describe the land cover (dense urban, buildings, residential, forest, open, villages....). Ground is
represented by a grid map where each bin is characterised by a code corresponding to a main type of cover (a clutter
class). The clutter maps are 8 bits/pixel (256 classes)-raster maps, they show an image with a colour assigned to each
clutter class (by default, grey shading).
Clutter file provides clutter code per bin. Bin size is defined by pixel size (P stated in metre). Pixel size must be the same
in both directions. Abscissa and ordinate axes are respectively oriented in right and down directions. First point given in
the file corresponds to the upper-left corner of the image. This point refers to the northwest point geo-referenced by A9155
Section 1 · Module 1 · Page 94
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 94
2.1 Geo databases
2.1.28 Morphostructure (2)
Besides the topo database the basic input for radio network planningEach propagation area has different obstacles like buildings, forest etc.Obstacles which have similar effects on propagation conditions are classified in morphoclassesEach morphoclass has a corresponding value for the correction gainThe resolution of the morphodatabases should be adaptedto the propagation modelMorpho correction factor for predictions:
0 dB (”skyscapers") … 30 dB (”water")
Morphodatabases (Landuse/Clutter) are a special kind of geodatabases. The morphodatabase is beside the topodatabase the basic input for radio network planning. Each morphoclass has a corresponding value of propagation loss. Together with a topographical database it is possible to predict the radio wave propagation.
Each propagation area has different obstacles like buildings, forest etc. Those obstacles, which have similar effects on propagation conditions are classified in morphoclasses.
This resolution of the morphodatabases should be adapted to the empirical propagation model for macrocellular radio network planning and the necessary planning resolution. In most cases the resolution of the rasterdatabases for morphostructure is around 50 ...100 m. With those values an optimum between calculation time and the necessary resolution of the prediction is reached in most radio network planning projects.
For microcellular radio network planning a buildingdatabase is needed with a higher resolution.
Each morphoclass is corresponding with a morpho-correction factor. The propagation loss is between 30 dB ("skyscrapers") ... and around 0 dB ("open area") The morphocorrection factors are achieved by calibration measurements
Section 1 · Module 1 · Page 95
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 95
2.1 Geo databases
2.1.29 Morphoclasses
Code Morpho-
structure Description
0 not classified e.g. edge of a database
1 skyscrapers / buildings
very high buildings ( >40m), very high density of buildings, no vegetation on ground level e.g. cities like NewYork, Tokio etc.
2 dense urban 4 or more storeys, areas within urban perimeters, inner city, very little vegetation, high density of buildings, most buildings are standing close together, small pedestrian zones and streets incl.
3 medium urban / mean
urban
3 or 4 storeys, areas within urban perimeters, most buildings are standing close together, less vegetation, middle density of buildings, small pedestrian zones and streets included
4 lower urban / suburban
2 or 3 storeys, middle density of buildings, some vegetation, terraced houses with gardens
5 residential 1-2 storeys, low density of buildings with gardens e.g. farmhouses, detached houses
6 industrial zone / industrial
factory, warehouse, garage, shipyards
Section 1 · Module 1 · Page 96
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 96
2.1 Geo databases
2.1.30 Morphoclasses (2)
Code Morpho-
structure Description
7 forest all kinds of forest, parks, with high tree density
8 agriculture / rural
high vegetation, plants: 1... 3 m, high density of plants, e.g. crop fields, fruit plantation
9 low tree density / parks
low vegetation, low height of plants, low density of plants, some kinds of parks, botanical garden
10 water sea, rivers, all kind of fresh- and saltwater
11 open area no buildings, no vegetation e.g. desert, beach, part of an airport, big streets etc. huge parking areas, large
12 (optional)
defined by networkplanner if necessary
13 (optional)
defined by networkplanner if necessary
Section 1 · Module 1 · Page 97
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 97
2.1 Geo databases
2.1.31Background data (streets, borders etc.)
All kinds of information data like streets, borders, coastlines etc.Necessary for orientationin plots of calculation resultsThe background data arenot needed for the calculationof the fieldstrength, power etc.
These data represent either polygons (regions...), or lines (roads, coastlines...) or points (towns...).
Section 1 · Module 1 · Page 98
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 98
2.1 Geo databases
2.1.32 Orthophoto
Georeferenced Satellite ImageResolution: most 10 or 20 mSatellite: e.g. SPOT, Landsat
These geographic data regroup the road maps and the satellite images ; they are only used for display and provide information about the geographic environment. A9155 supports scanned image files with TIFF (1, 4, 8, 24-bits/pixel), BIL (1, 4, 8, 24-bits/pixel), PlaNET© (1, 4, 8, 24-bits/pixel), BMP (1-24-bits/pixel) andErdas Imagine (1, 4, 8, 24-bits/pixel) formats.
Section 1 · Module 1 · Page 99
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 99
2.1 Geo databases
2.1.33 Scanned Maps
Mainly used asbackground dataNot used for calculationbut for localisationHas to be geocodedto put it into a GIS (Geographic Information System) e.g. a Radio Network Planning Tool
Section 1 · Module 1 · Page 100
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 100
2.1 Geo databases
2.1.34 Buildings
VectordataOutlines of
single buildingsbuilding blocks
Building heightsMaterial code
not: roof shape
Section 1 · Module 1 · Page 101
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 101
2.1 Geo databases
2.1.35 Buildings (2)
Microcell radio network planningis mainly used in urban environmentThe prediction of mircowavepropagation is calculated witha ray-tracing/launching modelA lot of calculationsteps are neededOptimum building databaserequired (data reduction) tominimize the pre-calculation time
Section 1 · Module 1 · Page 102
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 102
2.1 Geo databases
2.1.36 Traffic density
Advantageous in theinterference calculation,thus for frequencyassignment andin the calculationof average figures innetwork analysisRaster database of traffic densityvalues (in Erlangs) of thewhole planning areaResolution: 20...100 m
Section 1 · Module 1 · Page 103
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 103
2.1 Geo databases
2.1.37 Converting one single point (1a)
Example “Stuttgart” (Example 1)Long/Lat (WGS84) => UTM (WGS84)
Input:Longitude: 9 deg 11 min 7.5 secLatitude: 48 deg 45 min 13.5 secDatum “WGE: World Geodetic System 1984”; Projection: “Geodetic”
Exercise: Convert following example with the program “Geotrans”:
Output: Easting: 513629 mNorthing: 5400099 mDatum “WGE: World Geodetic System 1984”Projection: “Universersal Transverse Mercator (UTM)”Zone: 32 ; Hemisphere: N (North)
Preset of thisvalues necessary
Values, which willcalculated by program
Section 1 · Module 1 · Page 104
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 104
2.1 Geo databases
2.1.38 Converting one single point (1b)
GEOTRANS(Geographic Translator)is an application program which allows you to convert geographic coordinates easily among a wide variety of coordinate systems, map projections, and datums.
Example “Stuttgart” (Example 1)Long/Lat (WGS84) => UTM (WGS84)
Source: http://164.214.2.59/GandG/geotrans/
Section 1 · Module 1 · Page 105
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 105
2.1 Geo databases
2.1.39 Converting one single point (2a)
Input:Longitude: 9 deg 11 min 7.5 secLatitude: 48 deg 45 min 13.5 secDatum “WGE: World Geodetic System 1984”; Projection: “Geodetic”
Exercise: Convert following example with the program “Geotrans”:
Output: Easting: 513549 mNorthing: 5403685 mDatum “EUR-A: EUROPEAN 1950, Western Europe”Projection: “Universersal Transverse Mercator (UTM)”Zone: 32 ; Hemisphere: N (North)
Example “Stuttgart” (Example 2)Long/Lat (WGS84) => UTM (ED50) (ED50 = EUR-A = European Datum 1950)
Preset of thisvalues necessary
Values, which willcalculated by program
Section 1 · Module 1 · Page 106
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 106
2.1 Geo databases
2.1.40 Converting one single point (2b)
Example “Stuttgart” (Example 2)Long/Lat (WGS84) => UTM (ED50)(ED50 = EUR-A = European Datum 1950)
Attention: For flat coordinates (e.g. UTM) as well as for geographic coordinates (Long/Lat) a reference called “Geodetic Datum” is necessary.
Diff. X (Ex.2 - Ex.1): 69 mDiff. Y (Ex.2 - Ex.1): 200 mDifference because of different Geodetic Datums
Section 1 · Module 1 · Page 107
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 107
2.1 Geo databases
2.1.41 Converting a list of points (3a)
Example “Stuttgart” (Example 3 )Long/Lat (WGS84) => UTM (WGS84)
Input:text-file with the values (list) of the longitudeand latitude of different points(How to create the inputfile see on page 3c)
Output:Datum: “WGE: World Geodetic System 1984”Projection: “Universal Transverse Mercator (UTM)”Zone: 32
Preset of thisvalues necessary
Section 1 · Module 1 · Page 108
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 108
2.1 Geo databases
2.1.42 Converting a list of points (3b)
Example “Stuttgart” (Example 3 )Long/Lat (WGS84)
=> UTM (WGS84)
Section 1 · Module 1 · Page 109
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 109
2.1 Geo databases
2.1.43 Converting a list of points (3c)
Example “Stuttgart” (Example 3)Long/Lat (WGS84)=> UTM (WGS84)
Latitude Longitude UTM-ZoneHemisphere
Easting (x)Northing (y)
Optional: different error-infos,depending on the input-datadefault: “Unk”=“unknown”
Geotrans V2.2.3 Geotrans V2.2.3
deg min sec deg min sec
Section 1 · Module 1 · Page 110
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 110
2.1 Geo databases
2.1.44 Provider for Geospatial data
Geodatasupplier InternetBKS www.bks.co.ukComputaMaps www.computamaps.comGeoimage www.geoimage.frInfoterra www.infoterra-global.comIstar www.istar.frRMSI www.rmsi.com
Section 1 · Module 1 · Page 111
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 111
2.1 Geo databases
2.1.45 Links for more detailed infos
Maps Projection Overviewhttp://www.colorado.edu/geography/gcraft/notes/mapproj/mapproj.htmlhttp://www.ecu.edu/geog/http://www.wikipedia.org/wiki/Map_projection
Coordinate Transformation (online)http://jeeep.com/details/coord/http://www.cellspark.com/UTM.html
Map Collectionhttp://www.lib.utexas.edu/maps/index.html
Finding out Latitude/Longitude of cities etc. http://www.maporama.com
Section 1 · Module 1 · Page 112
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 112
2 Coverage Planning
2.2 Antennas and Cables
Section 1 · Module 1 · Page 113
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 113
2.2 Antennas and Cables
2.2.1.1 The Antenna System
AntennasPower dividerCables (jumper)Feeder cablesConnectorsClampsLightning protectionWall glandsPlanning
Rxdiv
Tx
Rx
Feedercable
Earthingkit
Wallgland
Jumper cables
Feederinstallationclamps
Plugs7/16“
Sockets7/16“
Mountingclamp
Grounding
Lightningrod Antennas
Earthing kit
Jumpercable Jumper
cable
Mechanicalantennasupportstructure
Section 1 · Module 1 · Page 114
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 114
2.2 Antennas and Cables
2.2.1.2 Antenna Theory
50Ω is the impedance of the cable377Ω is the impedance of the airAntennas adapt the different impedancesThey convert guided waves, into free-space waves (Hertzian waves) and/or vice versa
Z =377ΩZ =50Ω
It happens that the coulomb field and the induction field fall off much more rapidly than the radiation field with increasing distance from the antenna. At distances greater than a few wavelengths from the antenna, in what is called the antenna's far field, the electric field is essentially pure radiation. Closer to the antenna, we have the near field, which is a mixture of the radiation, induction and coulomb fields.
The coulomb field at an instant in time around a half-wave resonant dipole A half-cycle later, the polarity, and all the arrows, will be reversed. The spacing between the field lines indicates field strength.
Section 1 · Module 1 · Page 115
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 115
2.2 Antennas and Cables
2.2.1.3 Antenna Data
The antenna parameters which are of interest for the radio network engineering are the following:Antenna directivity, efficiency, gainPolarization, near field and far field
Specification due to certain wave polarization (linear/elliptic, cross-polarization)Half power beam width (HPBW)
Related to polarization of electrical fieldVertical and Horizontal HPBW
Antenna pattern, side lobes, null directionsYields the spatial radiation characteristics of the antenna
Front-to-back ratioImportant for interference considerations
Voltage standing wave ratio (VSWR)Bandwidth
In electrodynamics, polarization (also spelled polarisation) is the property of electromagnetic waves, such as light, that describes the direction of their transverse electric field. More generally, the polarization of a transverse wave describes the direction of oscillation in the plane perpendicular to the direction of travel. Longitudinal waves such as sound waves do not exhibit polarization, because for these waves the direction of oscillation is along the direction of travel.
Linear Circular Elliptical
Section 1 · Module 1 · Page 116
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 116
2.2 Antennas and Cables
2.2.1.4 Antenna Pattern and HPBW
0 dB
-3 dB
-10 dB
0 dB
-3 dB
-10 dB
verticalhorizontal
sidelobe
null direction
main beam
HPB
W
The antenna radiation pattern also named antenna diagram, describes the relative strength of the radiated field in various directions from the antenna, at a constant distance. The radiation pattern is a reception pattern as well, since it also describes the receiving properties of the antenna. The radiation pattern is three-dimensional, but usually as shown in Figure 4, the measured radiation patterns are a two dimensional slice of the three-dimensional pattern, in the horizontal or vertical planes.
This pattern depends on the antenna geometry and the current distribution in its elements. It is possible to compose, with a certain degree of freedom, arbitrary antenna diagrams by arranging antenna elements, e.g. dipoles, in groups, e.g. in a grid arrangement.
As shown in Figure, each antenna pattern consists of a couple of beams or lobes. One distinguishes the main beam, pointing in the direction where the maximum power is radiated, and the side lobes, which are local maxima in the antenna diagram. The side lobes must sometimes be treated with special care, as they could radiate too much power towards unplanned directions of the cell. This may lead to unexpected interference with other cells! The antenna has directions where it isn't nearly radiating. These directions are called null directions. They may cause coverage problems.
Based on the radiation pattern, the radio mobiles antennas are categorized in the following types:
Omni-directional antennas that provides a 360 degree horizontal radiation pattern. Omni antennas are typically used when continuous coverage around the site is needed and the offered traffic is low. Directional antennas that provide a stronger radiation pattern in a specific direction by focusing the radiation energy. For instance the radiation pattern shown in Figure, belongs to a directive antenna.
The sector or panel antennas are directional antennas and they are built based on the array antennas principle. Array antennas consist of a number of dipole antennas arranged in a geometrical manner to create a directional receiving or transmission pattern.
The panel antennas are used on sectorized sites in order to focus the coverage on special area of interest.
Section 1 · Module 1 · Page 117
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 117
2.2 Antennas and Cables
2.2.1.5 EIRP
Pt = 45 dBm
Gain = 11dBi
Isotropic radiated Power Pt
Effective isotropicradiated power:EIRP = Pt+Gain
= 56 dBm
V1
V2 = V1
radiatedpower
Known the antenna gain and the power fed into antenna, an important link budget parameter, the Effective Isotropic Radiated (EIRP) can be calculated. The EIRP represents the total power radiated by the antenna
Effective Isotropic Radiated Power
EIRP: Effective Isotropic Radiated Power (in main beam direction) in [dBm];
Pin: power fed into the antenna, [dBm];
G: antenna gain, [dBi];
GPEIRP in +=
Section 1 · Module 1 · Page 118
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 118
For the link between base station and mobile station, mostly linear antennas are used:
Monopole antennasMS antennas, car roof antennas
Dipole antennasUsed for array antennas at base stations for increasing the directivity of RX and TX antennas
2.2 Antennas and Cables
2.2.1.6 Linear Antennas
Section 1 · Module 1 · Page 119
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 119
2.2 Antennas and Cables
2.2.1.7 Monopole Antenna Pattern
Influence of antenna length on the antenna pattern
Section 1 · Module 1 · Page 120
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 120
2.2 Antennas and Cables
2.2.1.8 Panel Antenna with Dipole Array
Many dipoles are arranged in a grid layoutNearly arbitrary antenna patterns may be designed
Feeding of the dipoles with weighted and phase-shifted signalsCoupling of all dipole elements
Section 1 · Module 1 · Page 121
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 121
2.2 Antennas and Cables
2.2.1.9 Dipole Arrangement
Dipole arrangement
Typical flat panel antenna
Dipole element
Weightedandphaseshiftedsignals
Section 1 · Module 1 · Page 122
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 122
2.2 Antennas and Cables
2.2.1.10 Omni Antenna
Antenna with vertical HPBW for omni sitesLarge area coverage
AdvantagesContinuous coverage around the siteSimple antenna mountingIdeal for homogeneous terrain
DrawbacksNo mechanical tilt possibleClearance of antenna required
Section 1 · Module 1 · Page 123
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 123
2 Coverage Planning
2.2.2 Antenna Parameters
Section 1 · Module 1 · Page 124
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 124
2.2.2 Antennas Parameters
2.2.2.1 X 65° T6 900MHz 2.5m
Rural road coverage with mechanical uptiltAntenna
RFS Panel Dual Polarized Antenna 872-960 MHzAPX906516-T6 Series
Electrical specificationGain in dBi: 17.1Polarization: +/-45°HBW: 65°VBW: 6.5°Electrical downtilt: 6°
Mechanical specificationDimensions HxWxD in mm: 2475 x 306 x 120Weight in kg: 16.6
Horizontal Pattern
Section 1 · Module 1 · Page 125
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 125
2.2.2 Antennas Parameters
2.2.2.2 X 65° T6 900MHz 1.9m
Dense urban areaAntenna
RFS Panel Dual Polarized Antenna 872-960 MHzAPX906515-T6 Series
Electrical specificationGain in dBi: 16.5Polarization: +/-45°HBW: 65°VBW: 9°Electrical downtilt: 6°
Mechanical specificationDimensions HxWxD in mm: 1890 x 306 x 120Weight in kg: 16.6
Vertical Pattern
Section 1 · Module 1 · Page 126
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 126
2.2.2 Antennas Parameters
2.2.2.3 X 90° T2 900MHz 2.5m
Rural area with mechanical uptiltAntenna
RFS Panel Dual Polarized Antenna 872-960 MHzAPX909014-T6 Series
Electrical specificationGain in dBi: 15.9Polarization: +/-45°HPBW: 90°VBW: 7°Electrical downtilt: 6°
Mechanical specificationDimensions HxWxD in mm: 2475 x 306 x 120Weight in kg: 15.5
Vertical Pattern
Section 1 · Module 1 · Page 127
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 127
2.2.2 Antennas Parameters
2.2.2.4 V 65° T0 900MHz 2.0m
HighwayAntenna
RFS CELLite® Panel Vertical Polarized Antenna 872-960 MHzAP906516-T0 Series
Electrical specificationGain in dBi: 17.5Polarization: VerticalHBW: 65°VBW: 8.5°Electrical downtilt: 0°
Mechanical specificationDimensions HxWxD in mm: 1977 x 265 x 130Weight in kg: 10.9
Vertical Pattern
Section 1 · Module 1 · Page 128
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 128
2.2.2 Antennas Parameters
2.2.2.5 V 90° T0 900MHz 2.0m
Rural AreaAntenna
RFS CELLite® Panel Vertical Polarized Antenna 872-960 MHzAP909014-T0 Series
Electrical specificationGain in dBi: 16.0Polarization: VerticalHBW: 65°VBW: 8.5°Electrical downtilt: 0°
Mechanical specificationDimensions HxWxD in mm: 1977 x 265 x 130Weight in kg: 9.5
Vertical Pattern
Section 1 · Module 1 · Page 129
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 129
2.2.2 Antennas Parameters
2.2.2.4 X 65° T6 1800MHz 1.3m
Dense urban areaAntenna
RFS Panel Dual Polarized Antenna 1710-1880 MHzAPX186515-T6 Series
Electrical specificationGain in dBi: 17.5Polarization: +/-45°HBW: 65°VBW: 7°Electrical downtilt: 6°
Mechanical specificationDimensions HxWxD in mm: 1310 x 198 x 50Weight in kg: 5.6
Vertical Pattern
Section 1 · Module 1 · Page 130
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 130
2.2.2 Antennas Parameters
2.2.2.5 X 65° T2 1800MHz 1.3m
Dense urban areaAntenna
RFS Panel Dual Polarized Antenna 1710-1880 MHzAPX186515-T2 Series
Electrical specificationGain in dBi: 17.5Polarization: +/-45°HBW: 65°VBW: 7°Electrical downtilt: 2°
Mechanical specificationDimensions HxWxD in mm: 1310 x 198 x 50Weight in kg: 5.6
Vertical Pattern
Section 1 · Module 1 · Page 131
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 131
2.2.2 Antennas Parameters
2.2.2.6 X 65° T2 1800MHz 1.9m
HighwayAntenna
RFS Panel Dual Polarized Antenna 1710-1880 MHzAPX186516-T2 Series
Electrical specificationGain in dBi: 18.3Polarization: +/-45°HBW: 65°VBW: 4.5°Electrical downtilt: 2°
Mechanical specificationDimensions HxWxD in mm: 1855 x 198 x 50Weight in kg: 8.6
Vertical Pattern
Section 1 · Module 1 · Page 132
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 132
2.2.2 Antennas Parameters
2.2.2.7 V 65° T2 1800MHz 1.3m
HighwayAntenna
RFS CELLite® Panel Vertical Polarized Antenna 1710-1880 MHzAP186516-T2 Series
Electrical specificationGain in dBi: 17.0Polarization: VerticalHBW: 65°VBW: 7.5°Electrical downtilt: 2°
Mechanical specificationDimensions HxWxD in mm: 1310 x 198 x 50Weight in kg: 4.7
Horizontal Pattern
Section 1 · Module 1 · Page 133
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 133
2.2.2 Antennas Parameters
2.2.2.8 V 90° T2 1800MHz 1.9m
HighwayAntenna
RFS CELLite® Panel Vertical Polarized Antenna 1710-1880 MHzAP189016-T2 Series
Electrical specificationGain in dBi: 17.0Polarization: VerticalHBW: 90°VBW: 5.5°Electrical downtilt: 2°
Mechanical specificationDimensions HxWxD in mm: 1855 x 198 x 50Weight in kg: 6.0
Vertical Pattern
Section 1 · Module 1 · Page 134
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 134
2 Coverage Planning
2.2.3 Cable Parameters
Section 1 · Module 1 · Page 135
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 135
2.2.3 Cable Parameters
2.2.3.1 7/8" CELLFLEX® Low-Loss Coaxial Cable
Feeder Cable7/8" CELLFLEX® Low-Loss Foam-Dielectric Coaxial CableLCF78-50J StandardLCF78-50JFN Flame Retardant
Installation temperature >-25°C
Electrical specification 900MHzAttenuation: 3.87dB/100mAverage power in kW: 2.45
Electrical specification 1800MHzAttenuation: 5.73dB/100mAverage power in kW: 1.79
Mechanical specificationCable weight kg\m: 0.53Minimum bending radius
Single bend in mm: 120Repeated bends in mm: 250
Bending moment in Nm: 13.0Recommended clamp spacing: 0.8m
Section 1 · Module 1 · Page 136
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 136
2.2.3 Cable Parameters
2.2.3.2 1-1/4" CELLFLEX® Coaxial Cable
Feeder Cable1-1/4" CELLFLEX® Low-Loss Foam-Dielectric Coaxial CableLCF114-50J StandardLCF114-50JFN Flame Retardant
Installation temperature >-25°C
Electrical specification 900MHzAttenuation: 3.06dB/100mAverage power in kW: 3.56
Electrical specification 1800MHzAttenuation: 4.61dB/100mAverage power in kW: 2.36
Mechanical specificationCable weight kg\m: 0.86Minimum bending radius
Single bend in mm: 200Repeated bends in mm: 380
Bending moment in Nm: 38.0Recommended clamp spacing: 1.0m
Section 1 · Module 1 · Page 137
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 137
2.2.3 Cable Parameters
2.2.3.3 1-5/8" CELLFLEX® Coaxial Cable
Feeder Cable1-5/8" CELLFLEX® Low-Loss Foam-Dielectric Coaxial CableLCF158-50J StandardLCF158-50JFN Flame Retardant
Installation temperature >-25°C
Electrical specification 900MHzAttenuation: 2.34dB/100mAverage power in kW: 4.97
Electrical specification 1800MHzAttenuation: 3.57dB/100mAverage power in kW: 3.26
Mechanical specificationCable weight kg\m: 1.26Minimum bending radius
Single bend in mm: 200Repeated bends in mm: 508
Bending moment in Nm: 46.0Recommended clamp spacing: 1.2m
Section 1 · Module 1 · Page 138
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 138
2.2.3 Cable Parameters
2.2.3.4 1/2" CELLFLEX® Jumper Cable
CELLFLEX® LCF12-50J JumpersFeeder Cable
LCF12-50J CELLFLEX® Low-Loss Foam-Dielectric Coaxial Cable
Connectors7/16” DIN male/femaleN male/femaleRight angle
Molded version available in 1m, 2m, 3m
Mechanical specificationMinimum bending radius
Repeated bends in mm: 125
Electrical specification 900MHzAttenuation: 0.068db/mTotal losses with connectors are 0.108dB, 0.176dB and 0.244dB
Electrical specification 1800MHzAttenuation: 0.099dB/mTotal losses with connectors are 0.139dB, 0.238dB and 0.337dB
Section 1 · Module 1 · Page 139
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 139
2 Coverage Planning
2.3 Radio Propagation
Section 1 · Module 1 · Page 140
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 140
2.3 Radio Propagation
2.3.1 Propagation effects
Free space lossFresnel ellipsoidReflection, Refraction, Scattering
in the atmosphereat a boundary to another material
Diffractionat small obstaclesover round earth
AttenuationRain attenuationGas absorption
Fading
Section 1 · Module 1 · Page 141
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 141
ϕ
P0
Δh
2.3.1 Propagation effects
2.3.1.1 Reflection
Pr = Rh/v ⋅ P0
Rh/v = f(ϕ, ε, σ, Δh)horizontal reflection factorvertical reflection factorangle of incidencepermittivityconductivitysurface roughness
Rh
Rv
ϕεσΔh
Pr
Section 1 · Module 1 · Page 142
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 142
2.3.1 Propagation effects
2.3.1.2 Refraction
k = 4/3
k = 1 k = 2/3
k =
true earth
Ray paths with different k over true
∞
Considered via an effective earth radius factor k
Radio path plotted as a straight line by changing the earth's radius
k = 4/3k = 1
k = 2/3
k =
radio path
∞
earth
Section 1 · Module 1 · Page 143
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 143
2.3.1 Propagation effects
2.3.1.3 Diffraction
Occurs at objects which sizes are in the order of the wavelength λRadio waves are ‘bent’ or ‘curved’ around objects
Bending angle increases if object thickness is smaller compared to λInfluence of the object causes an attenuation: diffraction loss
diffracted radio shadow
zone obstacle
radio
Section 1 · Module 1 · Page 144
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 144
2.3.1 Propagation effects
2.3.1.4 Fading
Caused by delay spread of original signalMulti path propagationTime-dependent variations in heterogeneity of environmentMovement of receiver
Short-term fading, fast fadingThis fading is characterised by phase summation and cancellation of signal components, which travel on multiple paths. The variation is in the order of the considered wavelength. Their statistical behaviour is described by the Rayleigh distribution (for non-LOS signals) and the Rice distribution (for LOS signals), respectively.In GSM, it is already considered by the sensitivity values, which take the error correction capability into account.
Section 1 · Module 1 · Page 145
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 145
2.3.1 Propagation effects
2.3.1.5 Fading types
Mid-term fading, lognormal fadingMid-term field strength variations caused by objects in the size of 10...100m (cars, trees, buildings). These variations are lognormal distributed.
Long-term fading, slow fadingLong-term variations caused by large objects like large buildings, forests, hills, earth curvature (> 100m). Like the mid-term field strength variations, these variations are lognormal distributed.
Section 1 · Module 1 · Page 146
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 146
2.3.1 Propagation effects
2.3.1.6 Signal Variation due to Fading
-70
-60
-50
-40
-30
-20
-10
0
0.1
2.8
5.4
8.0
10.6
13.2
15.9
18.5
21.1
23.7
26.3
29.0
31.6
34.2
36.8
39.4
42.1
44.7
47.3
49.9
Distance [m]
Rec
eive
d Po
wer
[dB
m]
Lognormal fadingRaleygh fading
Fading hole
Raylaight/Rician Fading: Fast Fading. Rayleight : Statistical behaviour of Fast Fading signals for NON LOS-Signals.
Lognormal Fading
Section 1 · Module 1 · Page 147
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 147
2.3.1 Propagation effects
2.3.1.7 Lognormal Fading
Lognormal fading (typical 20 dB loss by entering a village)
Fading hole Lognormal fading (entering a tunnel)
Section 1 · Module 1 · Page 148
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 148
2 Coverage Planning
2.4 Path Loss Prediction
Section 1 · Module 1 · Page 149
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 149
2.4 Path Loss Prediction
2.4.1 Free Space Loss
The simplest form of wave propagation is the free-space propagationThe according path loss can be calculated with the following formulaPath Loss in Free Space Propagation
L free space lossd distance between transmitter and receiver antennaf operating frequency
L dkm
fMHzfreespace = + ⋅ + ⋅324 20 20. log log
Section 1 · Module 1 · Page 150
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 150
2.4 Path Loss Prediction
2.4.2 Fresnel Ellipsoid
The free space loss formula can only be applied if the direct line-of-sight (LOS) between transmitter and receiver is not obstructedThis is the case, if a specific region around the LOS is cleared from any obstaclesThe region is called Fresnel ellipsoid
Transmitter
Receiver
LOS
Section 1 · Module 1 · Page 151
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 151
2.4 Path Loss Prediction
2.4.3 Fresnel Ellipsoid
21
21
ddddr+
⋅⋅=
λThe Fresnel ellipsoid is the set of all
points around the LOS where the total length of the connecting lines to the transmitter and the receiver is longer than the LOS length by exactly half a wavelengthIt can be shown that this region is
carrying the main power flow from transmitter to receiver
Transmitter Receiver
LOS
LOS + λ/2
Fresnel zone
Section 1 · Module 1 · Page 152
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 152
2.4 Path Loss Prediction
2.4.4 Knife Edge Diffraction
1st Fresnel zone
r
BTS
MS
d1 d2
h0
line of sight
path of diffracted wave
d1 d2
h0
replaced obstacle (knife edge)
h0 = height of obstacle over line of sight
d1, d2 = distance of obstacle from BTS and MS
Knife edge diffraction
In case of an obstruction of the LOS path, the free-space formula with an additional correction term can be used if the obstacle is small compared to the distance from transmitter to receiver. Based on the assumption that this obstacle can be replaced by an ideal conducting half-plane which extends to infinity in the direction perpendicular to the propagation path and which is of infinitesimal thickness („knife-edge“), this situation refers to a field theory problem which can be solved in a deterministic way.
In the case that this knife-edge obstacle type enters the Fresnel region, diffraction occurs (similar to the diffraction known from optics) and introduces some additional diffraction loss compared to the free-space propagation.
The diffraction loss can be described by
with h0 the height of the obstacle above the LOS. v is a parameter which represents the number of „cleared“Fresnel ellipsoids. The function F(v) is shown in . One can see that the diffraction loss is 6dB if the obstacle is just touching the LOS.
λ2where)(
21
210
0 ⋅⋅+
⋅−=−==ddddh
rhvvFLdiff
Section 1 · Module 1 · Page 153
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 153
2.4 Path Loss Prediction
2.4.5 Knife Edge Diffraction Function
Knife-edge diffraction function
-5
0
5
10
15
20
25
30
35
-9 -8 -7 -6 -5 -4 -3 -2 -1 0 1 2 3
Clearance of Fresnel ellipsoid (v)
F(v)
[dB
]
Additional diffraction loss F(v)v: clearance parameter, v=-h0/rNote: h0 = 0 ⇒ v =0 ⇒ L = 6 dB
V=0:1=0
The function F(v) is shown on the top . One can see that the diffraction loss is 6dB if the obstacle is just touching the LOS. For v>1, some oscillation is noted, which appears due to the fact that the obstacle moves over several Fresnel regions where the phase of the transmitted signal is alternating between +180° and -180° phase shift.
In reality, the conductivity of the obstacle´s material is not ideal, and the oscillations appears „smoothed“ to an average value.
h0
r
d1 d2
LOS
h0
LOS
Section 1 · Module 1 · Page 154
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 154
2.4 Path Loss Prediction
2.4.6 "Final Solution" for Wave Propagation Calculations?
Exact field solution requires too much computer resources!Too much details required for inputExact calculation too time-consumingField strength prediction rather than calculation
Requirements for field strength prediction modelsReasonable amount of input dataFast (it is very important to see the impact of changes in the network layout immediately)Accurate (results influence the hardware cost directly)Tradeoff required (accurate results within a suitable time)Parameter tuning according to real measurements should be possible
Section 1 · Module 1 · Page 155
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 155
2.4 Path Loss Prediction
2.4.7 CCIR Recommendation
The CCIR Recommendations provide various propagation curves
Based on Okumura (1968)Example (CCIR Report 567-3):
Median field strength in urban areaFrequency = 900 MHzhMS = 1.5 mDashed line: free space
How to use this experience in field strength prediction models?
Model which fits the curves in certain ranges → Hata's model
was modified later by the European Cooperation in Science and Technology (COST): COST 231 Hata/Okumura
Section 1 · Module 1 · Page 156
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 156
2.4 Path Loss Prediction
2.4.8 Mobile Radio Propagation
Free-space propagation (Fresnel zone not obstructed) → L ~ d2
Fresnel zone heavily obstructed near the mobile station → L ~ d3.7
d
Section 1 · Module 1 · Page 157
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 157
2.4 Path Loss Prediction
2.4.9 Terrain Modeling
TopographyEffective antenna heightKnife edge diffraction
single obstaclesmultiple obstacles
Surface shape/Morpho-structureCorrection factors for Hata-Okumura formula
Section 1 · Module 1 · Page 158
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 158
2.4 Path Loss Prediction
2.4.10 Effect of Morphostructure on Propagation Loss
Open area Open areaUrban area
Distance
Fiel
dstr
engt
h
urban area
open area
Section 1 · Module 1 · Page 159
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 159
Path loss (Lu) is calculated (in dB) as follows:
Lu= A1 + A2 log(f) + A3 log(hBTS) + (B1 + B2log(hBTS)) log d
The parameters A1, A2, A3, B1 and B2 can be user-defined. Default values are proposed in the table below:
2.4 Path Loss Prediction
2.4.11 Okumura-Hata for GSM 900
-6.55-6.55B2
44.9044.90B1
-13.82-13.82A3
33.9026.16A2
46.3069.55A1
Cost-HataF>1500 MHz
Okumura-Hataf< 1500 MHz
Parameters
Hata formula empirically describes the path loss as a function of frequency, receiver-transmitter distance and antenna heights for an urban environment. This formula is valid for flat, urban environments and 1.5 metre mobile antenna height.
Section 1 · Module 1 · Page 160
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 160
2.4 Path Loss Prediction
2.4.12 CORRECTIONS TO THE HATA FORMULA
As described above, the Hata formula is valid for urban environment and a receiver antenna height of 1.5m. For other environments and mobile antenna heights, corrective formulas must be applied.
Lmodel1=Lu-a(hMS) for large city and urban environments
Lmodel1=Lu-a(hMS) -2log² (f/28) -5.4 for suburban area
Lmodel1=Lu -a(hMS) - 4.78log² (f)+ 18.33 log(f) – 40.94 for rural area
a(hMS) is a correction factor to take into account a receiver antenna height different from 1.5m.
3.2log² (11.75hMS) – 4.97Large city
(1.1log(f) – 0.7)hMS – (1.56log(f) -0.8)Rural/Small city
A(hMS)Environments
Note: When receiver antenna height equals 1.5m, a(hMS) is close to 0 dB regardless of frequency.
Section 1 · Module 1 · Page 161
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 161
2.4 Path Loss Prediction
2.4.13 Hata-Okumura for GSM 900
Formula valid for frequency range: 150…1000 MHz
Lmorpho [dB] Morpho/surface shape-Correction factor 0 dB: ‘Skyscrapers’->27 dB: ‘open area’
f [MHz] Frequency (150 - 1000 MHz)hBTS [m] Height of BTS (30 - 200 m)hMS [m] Height of Mobile (1 - 10m)d [km] Distance between BTS and MS (1 - 20 km)
Power law exponent shown colored
LossHata = 69.55 + 26.16 log (f) - 13.82 log (hBTS)- a(hMS) +(44.9 - 6.55 log (hBTS)) log (d) - Lmorpho
a (hMS) = (1.1 log (f) - 0.7) hMS - (1.56 log (f) - 0.8)
2.4 Path Loss Prediction 2.4 Path Loss Prediction
Section 1 · Module 1 · Page 162
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 162
2.4 Path Loss Prediction
2.4.14 COST 231 Hata-Okumura GSM 1800
Formula is valid for frequency range: 1500...2000 MHzHata’s model is extended for GSM 1800
Modification of original formula to the new frequency rangeFor cells with small ranges the COST 231 Walfish-Ikegami model is more
precisely
LossHata = 46.3 + 33.9 log (f) - 13.82 log (hBTS) - a(hMS) +(44.9 - 6.55 log (hBTS)) log (d) - Lmorpho
a (hMS) = (1.1 log (f) - 0.7) hMS - (1.56 log (f) -0.8)
Section 1 · Module 1 · Page 163
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 163
With:K1: constant offset (dB).K2: multiplying factor for log(d).d: distance between the receiver and the transmitter (m).K3: multiplying factor for log(HTxeff).HTxeff: effective height of the transmitter antenna (m). K4: multiplying factor for diffraction calculation. K4 has to be a positive number.Diffraction loss: loss due to diffraction over an obstructed path (dB).K5: multiplying factor for log(HTxeff)log(d).K6: multiplying factor for .: effective mobile antenna height (m).Kclutter: multiplying factor for f(clutter).f(clutter): average of weighted losses due to clutter.
( ) ( ) ( ) ( ) ( ) ( )clutterfKHKHdKlossnDiffractioKHKdKKL clutterRxeffTxeffTxeffel ++×+×+++= 654321mod loglog loglog
2.4.15 Alcatel Propagation Model (Standard Propagation Model)
Section 1 · Module 1 · Page 164
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 164
2.4 Path Loss Prediction
2.4.16 Alcatel Propagation Model
Using of effective antenna height in the Hata-Okumura formula:
ΤhRx eff = f(α, d, hBTS, hMS)
Section 1 · Module 1 · Page 165
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 165
2.4 Path Loss Prediction
2.4.17 Exercise ‘Path Loss’
ScenarioHeight BTS = 40mHeight MS = 1.5mD (BTS to MS) = 2000m
1. Calculate free space loss for A.) f=900MHzB.) f=1800MHz
2. Calculate the path loss for f = 900MHzA.) Morpho class ‘skyscraper’B.) Morpho class ‘open area’
3. Calculate the path loss for f = 1800MHzA.) Morpho class ‘skyscraper’B.) Morpho class ‘open area’
Morpho correction factors:
-Skyscraper: 0dB;
-Open area: 27dB
1. Calculate free space loss for
A.) f=900MHz: 97.6dB
B.) f=1800MHz: 103.6dB
2. Calculate the path loss for f = 900MHz
A.) Morpho class ‘skyscraper’: 135dB
B.) Morpho class ‘open area’: 108dB
3. Calculate the path loss for f = 1800MHz
A.) Morpho class ‘skyscraper’: 144.8dB
B.) Morpho class ‘open area’: 117.8dB
Section 1 · Module 1 · Page 166
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 166
2 Coverage Planning
2.5 Link Budget Calculation
Section 1 · Module 1 · Page 167
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 167
2.5 Link Budget Calculation
2.5.1 Maximum Propagation Loss (Downlink)
Feeder Cable LossLcable = 3 dB
BTS Antenna GainGantBS = 16.5 dBi
Effective Isotropic Radiated PowerEIRPBTS = 59.5 dBm
MS Antenna GainGantMS = 2 dBi
Internal LossesLint = 2 dB
ALCATEL EvoliumTM
Propagation LossLprop
Minimum Received PowerPRX,min,MS = -102 dBm
Maximum allowed downlink propagation loss: LMAPL = EIRPBTS - PRX,min,MS = 161.5 dB
MS RXSensitivity-102 dBm
Output Power at antenna connector 46.0 dBm
Exercice:Calculate the MAPL for this Example:
MAPL=
Add. Losses:
Anx = 1.8 dBAnc = 5.1 dBANy = 3.5 dB
----------Give the result for different using :1. With Combiner2. Without combiner
Pathloss without ANy = 153.6 dB
Section 1 · Module 1 · Page 168
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 168
Max. allowed uplink propagation loss: Lprop,max = EIRPMS - PRX,min,BTS = 157.5 dBWith antenna diversity gain of 3dB: Lprop,max,AD = EIRPMS - PRX,min,BTS + GAD = 160.5 dBWith TMA compensating cable loss: Lprop,max,AD,TMA = EIRPMS - PRX,min,BTS + GAD + GTMA = 163.5 dB
2.5 Link Budget Calculation
2.5.2 Maximum Propagation Loss (Uplink)
Feeder Cable LossLcable = 3 dB
BTS Antenna GainGantBS = 16.5 dBi
Minimum Received PowerPRX,min,BTS = -124.5 dBm
MS Antenna GainGantMS = 2 dBi
Internal LossesLint = 2 dB
ALCATEL EvoliumTM
Propagation LossLprop
EIRPMS = 33 dBm
MS TX Power33 dBm
Receiving sensitivity at ant. conn. -111 dBm
AD = Antenna Diversity ~3dB Gain
TMA = Tower Mounted Amplifier ~3-4 dB Gain
Exercice:Calculate the MAPL for these Examples:
MAPL(AD)=
MAPL(AD+TMA) =
Section 1 · Module 1 · Page 169
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 169
2.5 Link Budget Calculation
2.5.3 GSM900/1800 Link Budget
MAPLDL = EIRPDL - PISO_DL - MMAPLUL = EIRPUL - PISO_UL – MMaximum Allowable Path Loss
M = LSFM + LIF + LBODY + LPENM = LSFM + LIF + LBODY + LPENTotal Margins
LPENLPENPenetration Margin (indoor/in-car)
LBODYLBODYBody Loss
LIFLIFInterference Margin
LSFMLSFMSlow Fading Margin
Margins
EIRPDL = PTX_BTS - LEXT - LFEEDER - LJC - LTMA + GANT - LSLANTEIRPUL = PTX_MSEIRP
LSLANTSlant Polarization Loss
GANTAntenna Gain
LTMATMA Insertion Loss
LJCJumpers and Connectors Losses
LFEEDERFeeder Loss
LEXTExternal Device Losses
PTX_BTSPTX_MSTX Output Power
TX Parameters
PISO_DL = PRX_MSPISO_UL = PRX_BTS - GAD + LEXT + LFEEDER+LJC - GTMA- GANTIsotropic Power
GANTAntenna Gain
GTMATMA Contribution
LJCJumpers and Connectors Losses
LFEEDERFeeder Loss
LEXTExternal Device Losses
GADAntenna Diversity Gain
PRX_MSPRX_BTSRX Sensitivity
RX Parameters
DownlinkUplink
The GSM link budget components are described as follows:
UL/DL: measured in dBm, represent the BTS and the MS output power.
UL/DL: measured in dBm, express the BTS and MS receiver sensitivity.
DL only: the BTS antenna gain, measured in dBi. The MS antenna gain is normally assumed to be 0dBi.
UL only: the gain measured in dB that is caused by the diversity reception of the radio signal in uplink. Information concerning the antenna diversity gain
used for link budget calculation is given in;
UL only: the Tower Mounted Amplifier’s contribution in UL. It is expressed in dB.
DL only: the loss caused in DL path due to internal TMA filters and duplexers. It is a TMA catalog parameter and it is expressed in dB.
UL/DL: the loss due to the usage of external components such external diplexers, splitters, etc. It is measured in dB, and can be deduced from
respective data sheets.
UL/DL: the loss due to feeder cable, measured in dB.
UL/DL: the loss due to the usage of jumpers and connectors, measured in dB.
TX Output Power
RX Sensitivity
Antenna Gain
Antenna Diversity Gain
TMA Contribution
TMA Insertion Loss
External Device Loss
Feeder Loss
Jumper and Connector Loss
See also next page
Section 1 · Module 1 · Page 170
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 170
DL only: the polarization mismatch loss and represents a signal loss due todifferent polarization at the transmitting and receiving end, e.g. the usageof BTS cross polarized antenna at ± 45°. It is not applicable for MS.
As a rule of thumb, 0 dB is considered for slant polarization loss in case ofcross-polar antenna usage within the urban and sub-urban areas.Contrary, 1.5 to 3 dB is recommended in case of rural and open areas.For deeper aspects please.
UL/DL: the Effective Isotropic Radiated Power, measured in dBm.
UL/DL: the minimum power, measured in dB, required to maintain acertain level of service, at the receiver antenna. The calculation methodinside the link budget is described in page 169
UL/DL: Maximum allowable path loss. The weaker value is consideredwithin the network design process. Explanation on computation is shown inpage 169
UL/DL: called also log-normal margin, measured in dB, added to the pathloss calculation in order to increase the coverage probability at the cellborder to a certain value.
UL/DL: a margin measured in dB, added to the link budget in order tocompensate the signal degradation due to interference. A value of 3 dB istypical considered. More information on interference margin can be foundin GSM rec. 03.30.
UL/DL: a margin measured in dB, included to reflect the loss especiallyexperienced if handheld mobiles are used. It is occurring due to partialfield absorption in the human body. Typical values are 3 dB and 4 dB.Further details are specified in GSM rec. 03.30.
UL/DL: the penetration margin is measured in dB and is given on theservice class basis. Consequently, the penetration margin can be an in-caror an indoor margin:
► In-car margin measured in dB, added due to MS usage in a car.Typically a loss of 6 to 8 dB is assumed.
► Indoor margin measured in dB, added due to MS usage in indoorenvironment at ground floor level. Usually, indoor is referred to thefirst wall and no statement is given for deep indoor coverage. Itsrange varies from 10 to 18 dB.
► Deep indoor margin measured in dB, included due to MS usagedeep inside the buildings. Its range varies from 13 to 28 dB.
Slant Polarization Loss
EIRP
Isotropic Power
MAPL
Slow Fading Margin
Interference Margin
Body Loss Margin
Penetration Margin
Section 1 · Module 1 · Page 171
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 171
2.5 Link Budget Calculation
2.5.3 GSM900/1800 Link Budget
dB133,0dB133,0Max. Pathloss
dBm-87,0dBm-104,0Isotr. Rec. Power:
dB0,0Antenna Pre-Ampl.
dB0,0dB0,0Degradation (no FH)
90,9%
dB8,0dB8,0Lognormal Margin 50%→
dB3,0dB3,0Interferer Margin
dB3,0Diversity Gain
dBi2,0dBi11,0Antenna Gain
dB2,0dB3,0Cables, Connectors Loss
dB4,0Body/Indoor Loss
dBm-102,0dBm-104,0Rec. Sensitivity
DownlinkUplinkRX
dBm46,0dBm29,0EIRP
dBi11,0dBi2,0Antenna Gain
dB4,0Body/Indoor Loss
dB3,0dB2,0Cable,Connectors Loss
dBm38,0dBm33,0Output Power
dB3,0dB0,0Comb+Filter Loss, Tol.
dBm41,0dBm33,0Internal Power
DownlinkUplinkTXBS to MSMS to BS
GSM900 Link Budget(Example)
Section 1 · Module 1 · Page 172
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 172
2.5 Link Budget Calculation
2.5.4 GSM1800 Link Budget
TX Uplink DownlinkInternal Power 33 dBm 45.4 dBmComb+Filter Loss - 0 dBm - 5.3 dBmOutput Power 33 dBm 40.1 dBmCable+Conn Loss - 2 dB - 3 dBmBody/Indoor Loss - 4 dBAntenna Gain + 2 dBi + 11 dBiEIRP 29.0 dBm 48.1 dBm
RX Uplink DownlinkRec. Sensitivity - 109 dBm - 102 dBmBody/Indoor Loss + 4 dBCables, Con. Loss + 3 dB + 2 dBAntenna Gain - 11 dBi - 2 dBiDiversity Gain - 3 dBiInterferer Margin + 3 dB + 3 dBLognormal Margin + 8 dB + 8 dB
Isotr. Rec. Power - 109 dB - 87 dBmMax. Pathloss 138 dB 135.1 dB
Section 1 · Module 1 · Page 173
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 173
2.5 Link Budget Calculation
2.5.5 Additional Losses Overview
Loss type Reason Value
Indoor loss Electrical properties of wall material 20dB (3...30dB)
Incar loss Brass influencing radio waves 7dB (4...10dB)
Body loss Absorption of radio waves by thehuman body
3dB (0...8dB)
Interferer margin Both signal-to-noise ratio and C/I low 3 dB
Lognormal margin Receiving the minimum field strengthwith a higher probability
According toprobability
Section 1 · Module 1 · Page 174
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 174
2 Coverage Planning
2.6 Coverage Probability
Section 1 · Module 1 · Page 175
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 175
2.6 Coverage Probability
2.6.1 Indoor propagation aspects
Penetration Loss
Multiple Refraction
Multiple Reflection
Exact modeling of indoor environmentnot possiblePractical solution:empirical model!
Section 1 · Module 1 · Page 176
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 176
2.6 Coverage Probability
2.6.2 Indoor propagation: empirical model
d
Additional Loss in [dB] relative to loss at vertical incidence
Power relative to power at d=0
ϕ
d
0
5
10
15
20
25
30
35
0 6 12 18 24 30 36 42 48 54 60 66 72 78 84 90
Angle of incidence in degree
Ad
dit
ion
al
att
en
ua
tion
in
dB
Section 1 · Module 1 · Page 177
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 177
2.6 Coverage Probability
2.6.3 Indoor Penetration
Incident wave
Incident wave
Lindoor = 3 ... 15 dB
Lindoor = 13 ... 25 dBLindoor = ∞ dB (deep basement)
Lindoor = 17 ... 28 dB
-2.7 dB / floor(1st ... 10th floor)
-0.3 dB / floor(11th ... 100th floor)
Lindoor = 7 ... 18 dB(ground floor)
Depending on environmentLine-of-sight to antenna?Interior unknown
general assumptions
Section 1 · Module 1 · Page 178
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 178
2.6 Coverage Probability
2.6.4 Body Loss (1)
Measured attenuation versus
time for a test person walking
around in ananechoic chamber
Section 1 · Module 1 · Page 179
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 179
2.6 Coverage Probability
2.6.5 Body Loss (2)
Head modeled as sphere
Calculation model
Near field of MS antenna•without head•with head
Section 1 · Module 1 · Page 180
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 180
2.6 Coverage Probability
2.6.6 Body Loss (3)
Indirect measured field strength penetrated into the
head (horizontal cut)
Test equipment for indirectfield strength measurements
Section 1 · Module 1 · Page 181
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 181
2.6 Coverage Probability
2.6.7 Interference Margin
In GSM, the defined minimum carrier-to-interferer ration (C/I) threshold of 9 dB is only valid if the received server signal is not too weak.In the case that e.g. the defined system threshold for the BTS of -111dBm is approached, a higher value of C/I is required in order to maintain the speech quality.According to GSM, this is done by taking into account a correction of 3 dB.
Section 1 · Module 1 · Page 182
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 182
2.6 Coverage Probability
2.6.8 Degradation (no FH)
GSM uses a frame correction system, which works with checksum coding and convolutional codes.Under defined conditions, this frame correction works successfully and copes even with fast fading types as Rayleigh or Rician fading.For lower mobile speed or stationary use, the fading has a bigger influence on the bit error rate and hence the speech quality is reduced.In such a case, a degradation margin must be applied. The margindepends on the mobile speed and the usage of slow frequency hopping, which can improve the situation for slow mobiles again.
Section 1 · Module 1 · Page 183
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 183
2.6 Coverage Probability
2.6.9 Diversity Gain
This designates the optional usage of a second receiver antenna.The second antenna is placed in a way, which provides some decorrelation of the received signals.In a suitable combiner, the signals are processed in order to achieve a sum signal with a smaller fading variation range.Depending on the receiver type, the signal correlation, and the antenna orientation, a diversity gain from 2…6 dB is possible.
Section 1 · Module 1 · Page 184
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 184
2.6 Coverage Probability
2.6.10 Lognormal margin
Lognormal margin is also called fading marginDue to fading effects, the minimum isotropic power is only received with a certain probability
Signal statistics, lognormal distribution with median power value Fmed and standard deviation σ(sigma)
Without any margin, the probability is 50%, which is not a sufficient value in order to provide a good call success rate.A typical design goal should be a coverage probability of 90...95%. The following normalised table can be applied to find fading margins for different values of σ. The fading margin is calculated by multiplying the value of k (in the table) with the standard deviation: Lognormal/Fading Margin = kσ.
k -∞ -0.5 0 1 1.3 1.65 2 2.33 +∞
Coverage Probability
0% 30% 50% 84% 90% 95% 97.7%
99% 100%
k -∞ -0.5 0 1 1.3 1.65 2 2.33 +∞
Coverage Probability
0% 30% 50% 84% 90% 95% 97.7%
99% 100%
kk -∞-∞ -0.5-0.5 00 11 1.31.3 1.651.65 22 2.332.33 +∞+∞
Coverage Probability Coverage
Probability 0%0% 30%30% 50%50% 84%84% 90%90% 95%95% 97.7
%97.7%
99%99% 100%
100%
Section 1 · Module 1 · Page 185
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 185
2.6 Coverage Probability
2.6.11 Consideration of Signal Statistics (1)
100 m
100
m
BS
x
Field strength at location xlognormally distributedarround Fmedian
Section 1 · Module 1 · Page 186
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 186
2.6 Coverage Probability
2.6.12 Consideration of Signal Statistics (2)
0
0,05
0,1
0,15
0,2
0,25
0,3
received signal level F [dBm]
Local coverage probability: Pcov = P [ F > Fthreshold ]
σ
FmedianFthreshold
Area representing thecoverage probability
probability density function (pdf)
Folie large Scale (slow) Fading:The lognormal distribution, described by a mean fieldstrength Fmed and a standard deviation s, is shown in the
diagram. A coverage probability Pcov can be calculated, which defines the chance that a certain fieldstrength threshold Fthr is reached or exceeded by the calculated (or predicted) mean fieldstrength level Fmed.
The variation of the probability in dependence on Fmed is shown in the diagram. The required difference between Fmed and Fthr in order to achieve a required probability is called the fading margin.
Without any margin, the probability is 50% (Fmedian), which is not a sufficient value in order to provide a good call success rate. A typical design goal should be a coverage probability of 90...95%. This can be reached by applying a factor s (Fthreshold). (Additional System margin). -> Next Chapter
Section 1 · Module 1 · Page 187
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 187
2 Coverage Planning
2.7 Cell Range Calculation
Section 1 · Module 1 · Page 188
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 188
For what Radius R is the average coverage probability in the cell area 95% ?
2.7 Cell Range Calculation
2.7.1 Calculation of Coverage Radius R
r = distance between BTS and MS Frec = received powerσ = Standard deviation
F rec, thr
F rec
Frec,med (r)
0 r
σ
R
R
<Pcov(R)> = = 0.95∫20
π
πR²
Pcov (r) dr !
Frec,med (r) = EIRP - LossHata (r)
Loss Hata = f(hBS, hMS, f, r) + Kmor
Pcov(r)= P(Frec (r) > Frec,thr)
R = f (hBS, hMS, f, Kmor, EIRP, Frec,thr)
Section 1 · Module 1 · Page 189
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 189
2.7 Cell Range Calculation
2.7.2 Coverage Probability
0
0,5
0,951
Pcov (r)
R r
Pcov = P ( Frec > Frec, thr )
Section 1 · Module 1 · Page 190
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 190
2.7 Cell Range Calculation
2.7.3 Coverage Ranges and Hata Correction Factors
Area Coverage Probability
70%
75%
80%
85%
90%
95%
100%
0,0 1,5 3,0 4,5 6,0 7,5 9,0 10,5
d [km]
P cov
155
150
145
140
135
130
125
120
115
110
ReferencePathloss [dB]
Calculation conditions:
Correction = 3; Sigma = 7hBS = 30 m; hMS = 1.7m; f = 900 Mhz
Clutter type Cor [dB] σ [dB]
Skyscrapers 0 6Dense urban 2 6Medium urban 4 7Lower urban 6 7Residential 8 6Industrial zone 10 10Forest 8 8Agricultural 20 6Low tree density 15 8Water 27 5Open area 27 6
The lognormal distribution, described by a mean fieldstrength Fmed and a standard deviation s, is shown in in the left diagram. A coverage probability Pcov can be calculated, which defines the chance that a certain fieldstrength threshold Fthr is reached or exceeded by the calculated (or predicted) mean fieldstrength level Fmed. This probability is represented by the area enclosed by the graph of the probability density function and the vertical line at F=Fthr in the left diagram. The variation of the probability in dependence on Fmed is shown in the right diagram. The required difference between Fmed and Fthr in order to achieve a required probability is called the fading margin.
Without any margin, the probability is 50%, which is not a sufficient value in order to provide a good call success rate. A typical design goal should be a coverage probability of 90...95%. The following normalized table can be applied to find fading margins for different values of s. The fading margin is calculated by multiplying the value of k (in the table) with the standard deviation (Fading Margin = k s).
k -∞ -0.5 0 1 1.3 1.65 2 2.33 +∞Coverage
Probability 0% 30% 50% 84% 90% 95% 97.7% 99% 100%
Section 1 · Module 1 · Page 191
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 191
2.7 Cell Range Calculation
2.7.4 Conventional BTS Configuration
ALCATEL EvoliumTM
TX → 45.4 dBmRX → -109dBm
TX
TX a
nd
RX
1 BTSOmnidirectional antenna for both TX and RXCoverage Range R0
Coverage Area A0
R0
A0
Section 1 · Module 1 · Page 192
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 192
2.7 Cell Range Calculation
2.7.5 Coverage Improvement by Antenna Diversity
ALCATEL EvoliumTM
TX → 45.4 dBmRX → -109dBm
TX RX
DIV
RX a
nd T
X
1 BTSOmnidirectional antennas
one for both RX and TX one for RXDIV
Antenna diversity gain (2...6 dB)Example: 3 dB
Coverage rangeRDiv = 1.23 · R0
Coverage areaADiv = 1.5 · A0
R0RDiv
A0
ADiv
Section 1 · Module 1 · Page 193
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 193
2.7 Cell Range Calculation
2.7.6 Radiation Patterns and Range
3 antennas at sector site,Gain: 18 dBi, HPBW: 65°
Resulting antenna footprint ("cloverleaf")compared to an 11 dBi omni antenna
omni
sector
Section 1 · Module 1 · Page 194
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 194
2.7 Cell Range Calculation
2.7.7 Improvement by Antenna Diversity and Sectorization
TX
RX
DIV
3 BTSDirectional antennas (18 dBi)Antenna diversity (3 dB)Max. coverage rangeRsec,div = 1.95 · R0
Coverage areaAsec,div = 3 · A0
ALCATEL EvoliumTM
ALCATEL EvoliumTM
ALCATEL EvoliumTM
R0
Rsec,div
Asec,div
Section 1 · Module 1 · Page 195
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 195
2.7 Cell Range Calculation
2.7.8 Improvement by Antenna Preamplifier
TX
RX
DIV
3 BTSDirectional antennas (18 dBi)Antenna diversity (3 dB)Antenna preamplifier (3dB)Max. coverage rangeRsec,div,pre = 2.22 · R0
Coverage areaAsec,div,pre = 3.9 · A0
General:Asec = g · A0
g: Area gain factorR0
Rsec,div,pre
Asec,div,pre
ALCATEL EvoliumTM
ALCATEL EvoliumTM
ALCATEL EvoliumTM
Section 1 · Module 1 · Page 196
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 196
2 Coverage Planning
2.8 Antenna Engineering
Section 1 · Module 1 · Page 197
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 197
2.8 Antenna Engineering
2.8.1 Omni Antennas
ApplicationLarge area coverageUmbrella cell for micro cell layer
AdvantagesContinuous coverage around the siteSimple antenna mountingIdeal for homogeneous terrain
DrawbacksNo mechanical tilt possibleClearance of antenna requiredDensification of network difficult
Section 1 · Module 1 · Page 198
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 198
2.8 Antenna Engineering
2.8.2 Sector Antenna
Antenna with horizontal HPBW of e.g. 90° or 65°Advantages
Coverage can be focussed on special areasLow coverage of areas of no interest (e.g. forest)Allows high traffic loadAdditional mechanical downtilt possibleWall mounting possible
DrawbacksMore frequencies needed per site compared to omni sitesMore hardware neededLower coverage area per sector
Section 1 · Module 1 · Page 199
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 199
2.8 Antenna Engineering
2.8.3 Typical Applications
Wide horizontal beam width (e.g. 90°)For areas with few reflecting and scattering objects (rural area)Area coverage for 3-sector sitesSufficient cell overlap to allow successful handovers
Small horizontal beam width (e.g. 65°)For areas with high scattering (city areas)Coverage between sectors by scattering and by adjacent sites (mostly site densification in urban areas)
Section 1 · Module 1 · Page 200
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 200
2.8 Antenna Engineering
2.8.4 Antenna Tilt
Downtilting of the Antenna main beam related to the horizontal lineGoals:
Reduction of overshootRemoval of insular coverageLowering the interferenceCoverage improvement of the near area (indoor coverage)Adjustment of cell borders (handover zones)
Mechanical / Electrical or Combined downtilt
Section 1 · Module 1 · Page 201
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 201
2.8 Antenna Engineering
2.8.5 Mechanical Downtilt
AdvantagesLater adjustment of vertical tilt possibleAntenna diagram is not changed, i.e. nulls and side lobes remain in their position relative to the main beamCost effective (single antenna type may be used)Fast adjustments possible
DrawbacksSide lobes are less tiltedAccurate adjustment is difficultProblems for sites with difficult access
Section 1 · Module 1 · Page 202
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 202
2.8 Antenna Engineering
2.8.6 Electrical Downtilt
AdvantagesSame tilt for bothmain and side lobes
Antenna mounting is more simple → no adjustment errors
DrawbacksIntroduction of additional antenna types necessaryNew antenna installation at the site if downtilting is introducedLong antenna optimization phaseAdjustment of electrical tilt mostly not possible
τ = 0
τ = t
τ = 2 t
τ = 3 t
τ = delay time
downtilt angle
Section 1 · Module 1 · Page 203
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 203
2.8 Antenna Engineering
2.8.7 Combined Downtilt
Combination of both mechanical and electrical downtiltHigh electrical downtilt: Distinct range reduction in sidelobe direction (interference reduction)Less mechanical uptilt in main beam direction
Choose sector antennas with high electrical downtilt (6°...8°) and apply mechanical uptilt installation for optimum coverage range in main beam direction
Section 1 · Module 1 · Page 204
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 204
2.8 Antenna Engineering
2.8.8 Assessment of Required Tilts
Required tilt is estimated using Geometrical Optics
Consideration ofVertical HPBW of the antennaAntenna height above groundHeight difference antenna/location to be coveredMorpho-structure in the vicinity of the antennaTopography between transmitter and receiver location
Tilt must be applied for both TX and RX antennas!
Section 1 · Module 1 · Page 205
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 205
2.8 Antenna Engineering
2.8.9 Inter Site Distance in Urban Area
Using sectorized sites with antennas of 65° horizontal half power beam width
The sidelobe is approximately reduced by 10dB.This is a reduction of cell range to 50%.
The inter site distance calculation factor depends on
Type of antennaType of morpho class
Multi path propagationScatteringSigma (fading variations)
X XA B
0.5* R2R2
Section 1 · Module 1 · Page 206
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 206
2.8 Antenna Engineering
2.8.10 Downtilt in Urban Area
Cell range R2
Main beam
0.5* R2
Side l
obe
Tilt 2 Tilt 2Site A Site B
Inter Site Distance A-B = 1.5* R2
Section 1 · Module 1 · Page 207
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 207
2.8 Antenna Engineering
2.8.11 Downtilt in Urban Area
The upper limit of the vertical half power beam widthis directed towards the ground at maximum cell range
Upper –3dB point of the vertical antenna patternTo be used in areas with
Multi path propagation conditionGood scattering of the beam
AimReduction of interference
OptimizationCoverage Optimization in isolated cases using less downtiltInterference Reduction in isolated cases using more downtilt
Section 1 · Module 1 · Page 208
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 208
2.8 Antenna Engineering
2.8.12 Downtilt in Suburban and Rural Area
Downtilt planning forSuburbanRuralHighway Coverage
The main beam is directed towards the ground at maximum cell range
Main beamMain beam
Cell range R1 Cell range R1
Tilt 1 Tilt 1
Inter Site Distance C-D = 2* R1
Site C Site D
Section 1 · Module 1 · Page 209
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 209
2.8 Antenna Engineering
2.8.13 Antenna configurations
Application of DuplexerConsists of a TX/RX Filter and a combinerone antenna can be saved
Tower Mounted Amplifier (TMA)Increase Uplink SensitivityTMA needs to have TX bypass => in case of duplexer usage
DiversitySpace diversityPolarization diversity
Rx/Tx
RxTx
DuplexFilter
To BTS
Section 1 · Module 1 · Page 210
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 210
2.8 Antenna Engineering
2.8.14 Antenna Configurations for Omni and Sector Sites
Antenna Configurations for Omni and Sector Sites
RxRxdiv
TxRx
Tx
Rxdiv
Bracons
Sectorantenna
Pole
SectorAntenna
Pole
Tower mounting for omni antennas Tower mounting for directional antennas
Pole mounting for roof-top mounting
Pole mounting for wallor parapet mounting
Section 1 · Module 1 · Page 211
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 211
2.8 Antenna Engineering
2.8.15 Three Sector Antenna Configuration with AD
Section 1 · Module 1 · Page 212
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 212
2.8 Antenna Engineering
2.8.16 Antenna Engineering Rules
Distortion of antenna pattern: No obstacles withinAntenna near field rangeHPBW Rule plus security margin of 20°First fresnel ellipsoid range (additional losses!)
TX-RX Decoupling to avoid blocking and intermodulationRequired minimum separation of TX - RX antennas dependent on antenna configuration (e.g. duplexer or not)
Diversity gainRequired antenna separation for space diversity
Section 1 · Module 1 · Page 213
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 213
2.8 Antenna Engineering
2.8.17 Distortion of antenna pattern
Antenna Near Field Range: Rmin = 2D²/λD = Aperture of antenna (e.g. 3m) => Rmin = 60 / 120m for GSM / DCS
HPBW Rule with securtiy margin of 20° and tilt α
Roof Top = Obstacle
ϕϕ = HPBW/2 + 20° + α
D
H
D[m] 1 5 10H[m] 0.5 2.5 5
HPBW = 8°, α = 2°
Section 1 · Module 1 · Page 214
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 214
2.8 Antenna Engineering
2.8.18 Tx-Rx Decoupling (1)
TX
RX
fuse
fint
f[MHz]
P [dBm]
fuse fint
-101
-13
n*200kHz
Pout
Pin
ReceiverCharacteristic
Pblock
P1dB
Out of Band Blocking Requirement (GSM Rec. 11.21)GSM 900 = +8 dBmGSM 1800 = 0 dBm
Required Decoupling (n = number of transmitters)
TX-TX = 20 dBTX-RX GSM = 30 + 10 log (n) dBTX-RX DCS = 40 + 10 log (n) dB
Section 1 · Module 1 · Page 215
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 215
2.8 Antenna Engineering
2.8.19 TX-RX Decoupling (2)
Horizontal separation (Approximation)
IH=22+20log(d
H/λ)-(G
T+G
R) [dB]
dH
Isolation for Horizontal Separation - omni 11dBi
15
20
25
30
35
40
45
1,7 2,7 3,7 4,7 5,7 6,7 7,7 8,7 9,7 10,4
10,8
11,2
11,6 12 12
,412
,813
,213
,6 14 14,4
14,8
15,2
Separation [m]
Isol
atio
n [d
B]
GSM1800
GSM900
Section 1 · Module 1 · Page 216
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 216
2.8 Antenna Engineering
2.8.20 TX-RX Decoupling (3)
Vertical separation (Approximation)
IV=28+40log(d
V/λ) [dB]
dv
dm
Mast
Isolation for Vertical Separation
0
10
20
30
40
50
60
70
0,2 0,3 0,4 0,5 0,6 0,7 0,8 0,9 1
Separation [m]
Isol
atio
n [d
B]
GSM1800
GSM900
Section 1 · Module 1 · Page 217
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 217
Required separation for max. diversity gain = F(λ)
2.8 Antenna Engineering
2.8.21 Space Diversity
dH
RXA RXB
dV
RXA
RXB
For a sufficient low correlation coefficient ρ < 0.7:
dH = 20λ => GSM 900: 6m / GSM1800: 3m
dV = 15λ => GSM 900: 4.5m / GSM1800: 2.25m
Section 1 · Module 1 · Page 218
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 218
2.8 Antenna Engineering
2.8.22 Power Divider
Power dividers connect severalantennas to one feeder cable
For combination of individualantenna patterns for a requested configuration
Quasi-omni configurationBidirectional configuration(road coverage)
4-to-1 Power splitter(6 dB loss)
To BTS: Receiver input
To BTS: Duplexer output(TX plus RX diversity)
Quasi-OmniConfiguration
Section 1 · Module 1 · Page 219
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 219
Power dividerAlso called "power splitter" or "junction box"Passive device (works in both (transmit and receive) direction)
3 dB
Pin
Pin
2Pin
2
Pin
3
4.5 dB
Pin
Pin
3Pin
3
6 dB
Pin
Pin
4Pin
4Pin
4Pin
4
2.8 Antenna Engineering
2.8.23 Power Divider
Section 1 · Module 1 · Page 220
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 220
2.8 Antenna Engineering
2.8.24 Panel Configurations (1)
Radial Arrangement
of 6 Panel Antennas with horizontal beamwidth = 105 °gain = 16.5 dBi, mast radius = 0.425 m, mounting radius = 0.575 m
Section 1 · Module 1 · Page 221
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 221
2.8 Antenna Engineering
2.8.25 Panel Configurations (2)
Example 2: Quasi Omni Arrangement
of 3 antennas with horizontal beamwidth = 105 °, gain =13.5 dBi,mounting radius = 4 m
Section 1 · Module 1 · Page 222
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 222
2.8 Antenna Engineering
2.8.26 Panel Configurations (3)
Example 3: Skrew Arrangement
of 4 Panel Antennas with horizontal beamwidth = 65 °,gain = 12.5 dBi, mast radius = 1 m,mounting radius = 1.615 m
Section 1 · Module 1 · Page 223
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 223
2.8 Antenna Engineering 2.8.27 Feeders
Technical summary
Inner conductor: Copper wire
Dielectric: Low density foam PE
Outer conductor: Corrugated copper tube
Jacket: Polyethylene (PE)black
Inner conductor Outer conductor
Dielectric Jacket
Section 1 · Module 1 · Page 224
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 224
2.8 Antenna Engineering
2.8.28 Feeder Installation Set and Connectors
1 Cable Clamps2 Antenna Cable3 Double Bearing4 Counterpart5 Anchor tape
7/16 Connector:Coaxial ConnectorRobustGood RF-Performance
Section 1 · Module 1 · Page 225
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 225
Type Minimum bending radius Jacket(outer diameter)
Weight (m) Recommendedclamp spacing
Single bending Repeated bending
LCF 1/2’’ 70 mm 210 mm 16 mm 0.35 kg 0.6 m
LCF 7/8’’ 120 mm 360 mm 28 mm 0.62 kg 0.8 m
LCF 1 5/8’’ 300 mm 900 mm 49.7 mm 1.5 kg 1.2 m
These values are based on feeder types with an impedance of 50 ohms
GSM 900 GSM 1800 GSM 1900
Type Attenuation /100 m [dB]
Recommendedmax length [m]
Attenuation /100 m [dB]
Recommendedmax length [m]
Attenuation /100 m [dB]
Recommendedmax length [m]
LCF 1/2“ 6.6 45 10.3 30 10.6 28LCF 7/8“ 4.0 75 6.0 50 6.3 47LCF 1_5/8“ 2.6 115 4.0 75 4.2 71
2.8 Antenna Engineering
2.8.29 Feeder Parameters
Section 1 · Module 1 · Page 226
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 226
2.8 Antenna Engineering
2.8.30 Feeder attenuation (1)
Main contribution is given by feeder lossFeeder Cable 4dB/100m => length 50m Loss =2.0dBJumper Cable 0.066dB/1m => 5m Loss =0.33dBInsertion Loss of connector and power splitter < 0.1dBTotal Loss 2.0dB+2x0.33dB+5x0.1dB+0.1dB =3.26dB
Cable type is trade off betweenHandling flexibilityCost Attenuation
Section 1 · Module 1 · Page 227
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 227
2.8 Antenna Engineering 2.8.31 Radiating Cables
Provide coverage in Tunnels, buildings, along side tracks or lines
Principle: Radiate a weak but constant electromagnetic wave
Suitable for coverage over longer distances (Repeater)
Fieldstrength distribution more constant as with antennas
F
FThr
Repeater
F
FThr
Terminat-ing Load
Section 1 · Module 1 · Page 228
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 228
Components are shown with black lines
BTS
Tx
Rx
Radiating cable Termination load
Earthing kitMounting clips with 50 mm wall standoff
N-connections
Jumper cabel
1-leg radiating cable system
2.8 Antenna Engineering
2.8.32 Components of a radiating cable system
Section 1 · Module 1 · Page 229
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 229
-40
-50
-60
-70
-80
-90
-100
-110
[dBm]
Cable attenuationbetween the antennas
Radiating cable field strength
Antenna field strength
Distance
2.8.33 Comparison of field strength: Radiating cable and standard antenna
Section 1 · Module 1 · Page 230
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 230
Example of a radiating cable in a tunnel
2.8 Antenna Engineering
2.8.34 Example of a radiating cable in a tunnel
Section 1 · Module 1 · Page 231
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 231
2.8 Antenna Engineering
2.8.35 Microwave antennas, feeders and accessories
Microwave point to point systems use highly directional antennasGain
with G = gain over isotropic, in dBiA = area of antenna aperturee = antenna efficiency
Used antenna typesparabolic antennahigh performance antennahorn lens antennahorn antenna
G A e= 10 4
2lg π
λ
Section 1 · Module 1 · Page 232
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
Parabolic dish, illuminated by a feed horn at its focus.
Available in a wide variety of sizes [1’ (0.3 m), 2’ (0.6 m), 4’ (1.2 m), 6’ (1.8 m), 8’ (2.4 m), 10’ (3.0 m) and sometimes up to 16’ (4.8 m) in most frequency bands.
Sizes over 4’ are seldom used due to the installation restrictions on private buildings
Mostly with single plane polarised feed, which can be either vertical (V) or horizontal (H)
Dual polarized feeds (DP), with separate V and H connections possible
DP`s usually have lower gain than single polarized antennas
Front-to-back ratios of about 45 dB are not high enough to use these antennas back-to-back on the same frequency (interference calculations)
Antenna patterns are absolutely necessary for interference calculations
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 232
2.8 Antenna Engineering
2.8.36 Parabolic antenna
Parabolic dish, illuminated by a feed horn at its focusAvailable sizes: 1’ (0.3 m) up to 16’(4.8 m)Sizes over 4’ seldom used due to installation restrictions Single plane polarized feed vertical (V) or horizontal (H)Also: dual polarized feeder (DP), with separate V and H connections (lower gain)Front-to-back ratios of 45 dB not high enough for back-to-back configuration on the same frequencyAntenna patterns are absolutely necessary for interference calculations
Section 1 · Module 1 · Page 233
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
Similar to the common parabolic antenna, except for an attached cylindrical shield
Improvement of the front-to-back ratio, and wide angle radiation discrimination
Available in the same sizes as parabolic ones, either single or double polarised
Substantially bigger, heavier, and more expensive than the ordinary parabolics
Allow back-to-back transmision at the same frequency in both directions (refer to interferencecalculation)
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 233
2.8 Antenna Engineering
2.8.37 High performance antenna
Similar to common parabolic antenna, except for attached cylindrical shieldImprovement of front-to-back ratio and wide angle radiation discriminationAvailable in same sizes as parabolic, single or dual polarizedSubstantially bigger, heavier, and more expensive than parabolic antennasAllow back-to-back transmission at the same frequency in both directions (refer to interference calculation)
Section 1 · Module 1 · Page 234
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
Horn lens antenna
Only available for very high frequencies (above 25 Ghz)
Replacement for small parabolic antennas (1’)
Electrical data nearly the same, but easier to install due to their size and weight
Horn reflector antennaConsists of a very large parabola, mounted at such an angle that the energy from the feed horn is
reflected at right angle (90°)
Gain in the region of a 10’ parabolic antenna (60 dBi), but it has much higher front-to-back ratios ( 70 dB or more)
Very big, heavy and requires a complex installation procedure
Only used on high capacity microwave backbones (example: MSC-MSC interconnections).
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 234
2.8 Antenna Engineering
2.8.38 Horn antennas
Horn lens antennaFor very high frequencies > 25 GHzReplacement for small parabolic antennas (1’) Same electrical data, but easier to install due to size and weightHorn reflector antennaLarge parabola, energy from the feed horn is reflected at right angle (90°)Gain like 10’ parabolic antenna (60 dBi), but higher front-to-back ratios > 70 dB
Big and heavy, requires a complex installation procedureOnly used on high capacity microwave backbones (e.g. MSC-MSC interconnections)
Section 1 · Module 1 · Page 235
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 235
2.8 Antenna Engineering
2.8.39 Specific Microwave Antenna Parameters (1)
Cross polarization discrimination (XPD)highest level of cross polarisation radiation relative to the main beam; should be > 30 dB for parabolic antennas
Inter-port isolationisolation between the two ports of dual polarised antennas; typical value: better than 35 dB
Return loss (VSWR)Quality value for the adaption of antenna impedance to the impedance of the connection cableReturn loss is the ratio of the reflected power to the power fed at the antenna input (typical> 20 dB)
Section 1 · Module 1 · Page 236
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 236
Radiation pattern envelope (RPE)Tolerance specification for antenna pattern (specification of antenna pattern itself not suitable due to manufacturing problems)Usually available from manufacturer in vertical and horizontal polarisation (worst values of several measurements)
Weight
Wind load
2.8 Antenna Engineering
2.8.40 Specific Microwave Antenna Parameters (2)
Section 1 · Module 1 · Page 237
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 237
2.8 Antenna Engineering
2.8.41 Data sheet 15 GHz
Parabolic antenna 15 GHz High performance antenna 15 GHz
Bandwidth (GHz) 14.4 - 15.35 14.4 - 15.35 14.4 - 15.35 Model number PA 2 - 144 PA 4 - 144 PA 6 - 144 Nominal diameter (m) 0.6 1.2 1.8
(ft) 2 4 6
Half-power beamwidth (deg) 2.3 1.2 0.8 Gain low band (dBi) 36.2 42.3 45.8 Gain mid band (dBi) 36.5 42.5 46.0 Gain high band (dBi) 36.7 42.8 46.3 Front-to-back ratio (dB) 42 48 52 Cross polar discrimination (dB) 28 30 30 Return loss (dB) 26 26 28
Weight (kg) 19 43 73 Windload Elevation adjustment (deg) +/- 5 +/- 5 +/- 5
Bandwidth (GHz) 14.4 - 15.35 14.4 - 15.35 14.4 - 15.35Model number DA 2 - 144 DA 4 - 144 DA 6 - 144Nominal diameter (m) 0.6 1.2 1.8
(ft) 2 4 6
Half-power beamwidth (deg) 2.3 1.2 0.8Gain low band (dBi) 36.2 42.3 45.8Gain mid band (dBi) 36.5 42.5 46.0Gain high band (dBi) 36.7 42.8 46.3Front-to-back ratio (dB) 65 68 68Cross polar discrimination (dB) 28 30 30Return loss (dB) 26 26 26
Weight (kg) 28 55 130WindloadElevation adjustment (deg) +/- 12 +/- 12 +/- 12
Section 1 · Module 1 · Page 238
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 238
2.8 Antenna Engineering
2.8.42 Radiation pattern envelope
Section 1 · Module 1 · Page 239
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
Depending on the frequency coaxial cables and waveguides are used for the transmission of RF energy between radio systems and antennas. The most important characteristic of feeders is their loss, but also
their impedance (return loss).
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 239
2.8 Antenna Engineering
2.8.43 Feeders (1)
Coaxial cables or waveguides (according to frequency)Most important characteristic: loss and return lossCoaxial cables
Used between 10 MHz and 3 GHz Dielectric material: foam or airParameters of common coaxial cables:
type dielectric diameter(mm)
loss(dB/100m)
powerrating (kW)
bendingradius (mm)
LCF 1/2’ CU2Y foam 16.0 10,9 / 2 GHz 0.47 20013.8 / 3 GHz
LCF 7/8’ CU2Y foam 28.0 6.5 / 2 GHz 0.95 3608.5 / 3 GHz
LCF 1 5/8’ CU2Y foam 49.7 4.4 / 2 GHz 1.7 3805.6 / 3 GHz
Section 1 · Module 1 · Page 240
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 240
2.8 Antenna Engineering
2.8.44 Feeders (2)
WaveguidesUsed for frequency bands above 2.5 GHzThree basic types available: circular, elliptical and rectangular
Rigid circular waveguideVery low lossSupports two orthogonal polarisationsCapable to carry more than one frequency bandUsually, short components of this type are usedDisadvantages: cost, handling and moding problems
Section 1 · Module 1 · Page 241
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 241
2.8 Antenna Engineering
2.8.45 Feeders (3)
Elliptical semiflexible waveguidesAcceptable loss, good VSWR performanceLow cost and easy to installVarious types optimised for many frequency bands up to 23 GHzUsed for longer distances (easy and flexible installation)Can be installed as a "single run" (no intermediate flanges)
type loss /100 m FrequencyEW 34 2.0 4 GHzEW 52 4.0 6GHzEW 77 5.8 8GHzEW 90 10.0 11 GHzEW 220 28.0 23 GHz
Section 1 · Module 1 · Page 242
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 242
2.8 Antenna Engineering
2.8.46 Feeders (4)
Solid and flexible rectangular waveguidesSolid rectangular waveguides
Combination of low VSWR and low lossHigh cost and difficult to installUsed for realising couplers, combiners, filters
type loss /100 m FrequencyWR 229 2.8 4 GHzWR159 4.5 6GHzWR112 8.5 8GHzWR 90 11.7 11 GHzWR 75 15.0 13 GHz
Section 1 · Module 1 · Page 243
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 243
2.8 Antenna Engineering
2.8.47 Feeders (5)
Flexible rectangular waveguidesWorse VSWR and losses than for solid waveguidesOften used in short lengths (<1 m), where position between connection points depends on actual installation placeCommon applications: connection of microwave system to antenna (close together on rooftops or towers) for frequencies >13 Ghz
type loss / m FrequencyPDR140 0.5 15GHzPDR180 1 18 GHzPDR220 2 23 GHz
Section 1 · Module 1 · Page 244
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 244
2.8 Antenna Engineering
2.8.48 Antenna feeder systems (1)
Direct radiating systemMost commonly used for frequencies up to 13 GhzDepending on accepted feeder loss/length, higher frequencies may be possibleExcessive attenuation and costs in long runs of wave guideOccurence of echo distortion due to mismatch in long runs of waveguide possible
Section 1 · Module 1 · Page 245
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 245
2.8 Antenna Engineering
2.8.49 Antenna feeder systems (2)
Periscope antenna systemUsed for
considerable antenna heightswaveguide installation problems
Negligible wave guide cost and easy installationSystem gain is a function of antenna and reflector size, distance and frequencyUsed above 4 GHz , because reflector size is prohibitive for lower frequencies
Section 1 · Module 1 · Page 246
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 246
2.8 Antenna Engineering
2.8.50 Antenna feeder systems (3)
Combined antenna with transceiverAntenna and transceiver are combined as a single unit to cut out wave guide loss (higher frequencies)Units are mounted on top of a mast and connected to multiplex equipment via cable
Section 1 · Module 1 · Page 247
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 247
2 Coverage Planning
2.9 Alcatel BSS
Section 1 · Module 1 · Page 248
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 248
2.9 Alcatel BSS
2.9.1 Architecture of BTS - Evolium Evolution A9100
3 levels
Antenna coupling level
TRX level
BCF level Station unit module
Abis interface
Abbreviations BCF Base station Control Function TRX Transceiver
Antenna network stage ANC
Air interface
Combiner stage (ANY) Combiner stage (ANY)
TRX TRX TRX TRX TRX TRX TRX TRX TRX TRX TRX TRX TRX TRX TRX TRX TRX TRX TRX TRX TRX TRX TRX TRX
Antenna network stage ANC or ANB (note)
Note 1 : ANB module is limited to 2 TRX in No TX Div mode and to 1 TRX in TX Div mode.
Antenna coupling levelThe general functions performed at this level are:- Duplexing transmit and receive paths onto common antennas;- Feeding the received signals from the antenna to the receiver front end, where the signals are amplified and distributed to the different receivers (Low Noise Amplifier (LNA) and power splitter functions);- Providing filtering for the transmit and the receive paths;- Combining, if necessary, output signals of different transmitters and connecting them to the antenna(s);- Supervising antennas VSWR (Voltage Standing Wave Ratio).-Powering and supervising TMA through the feeder.
The Antenna Network Combiner (ANC) module- one duplexer allowing a single antenna to be used for the transmission and reception of both downlink and uplink channels- hence minimizing the number of antenna - a frequency selective VSWR meter to monitor antenna feeder and antenna- one LNA amplifying the receive RF signal, and giving good VSWR values, noise compression and good reliability- two splitter levels distributing the received signal to four separate outputs so that each output receives the signal from its dedicated antenna and from the second one (diversity)- one Wide Band Combiner (WBC), concentrating two transmitter outputs into one, only for configurations with more than two TRX- insertion of 12V DC current in the feeder in order to provide power to TMAs when TMAs are used; there is thus no need for separate Power Distribution Unit (PDU) nor Bias-Tee (Feeder Lightning protections, that come with the ANC in case of outdoor BTSs, are themselves of a new type, compatible with this DC power feeding) (This function is only available with the new Evolution version of this module; it can be disabled, even if TMAs are used, in case those TMAs have their own PDUs).
Section 1 · Module 1 · Page 249
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 249
2.9 Alcatel BSS
2.9.2 EVOLIUMTM A9100 Base Station (1)
The Antenna network Combiner (ANc)- no-combining mode
Antenna ATXA - RXA -RXdivB
SplitterWBC
TRX 1 TX RXn RXd
TRX 2TXRXnRXd
Splitter
Splitter
LNA
Duplexer
FilterFilter
Splitter Splitter WBC
Antenna BTXB- RXB -RXdivA
Duplexer
FilterFilter
Splitter
LNA
By-pass functionBy-pass function
No-combining mode & No TX Div mode
The No-combining mode for configuration up to 2 TRX if TX Diversity is not used, or up to one TRX if TX Diversity is used (two TRX ports must then be connected to the two Antenna Connector ports
of a same Twin TRX module); in these cases, the Wide Band Combiner is not needed, and therefore bypassed
Section 1 · Module 1 · Page 250
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 250
2.9 Alcatel BSS
2.9.3 EVOLIUMTM A9100 Base Station (2)
The Antenna network Combiner (ANc)- Combining mode & No TX Div mode
Antenna A TXA - RXA - RXdivB
Splitter WBC
TRX 1 TX RXn RXd
TRX 4TXRXnRXd
Splitter
Splitter
LNA
Duplexer Filter Filter
Splitter Splitter WBC
Antenna BTXB- RXB - RXdivA
Duplexer
FilterFilter
Splitter
LNA
TRX 2TX RXn RXd
TRX 3TXRXnRXd
The Combining mode for configuration from 3 up to 4 TRX if TX Diversity is not used, or up to 2 TRX if TX Diversity is used (two TRX ports must then be connected to the two Antenna Connector ports
of a same Twin TRX module); in these cases, the Wide Band combiner is not bypassed, as shown in the figure
Section 1 · Module 1 · Page 251
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 251
2.9 Alcatel BSS
2.9.4 EVOLIUMTM A9100 Base Station (3)
ANy: Twin Wide Band Combiner Stage
Splitter SplitterWBC SplitterSplitter WBC
TXA RXA RXAdiv
TX RX RXdiv
TRX 1
TX RX RXdiv
TRX 2
Rxdiv RX TX
TRX 4
Rxdiv RX TX
TRX 3
RXBdiv RXB TXB
The Twin Wide Band Combiner stage (ANY) combines up to four transmitters into two outputs, and distributes the two received signals up to four receivers. This module includes twice the same structure, each structure containing:
●one wide band combiner (WBC), concentrating two transmitter outputs into one ● two splitters, each one distributing the received signal to two separate outputs
providing diversity and non-diversity path
Section 1 · Module 1 · Page 252
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 252
2.9 Alcatel BSS
2.9.5 EVOLIUMTM BTS Features
Standard Features according to GSMDR (Dual Rate), EFR (Enhanced Full Rate coder), AMR (Adaptive Multi Rate) requires that the BSS software release and the other network elements also support these codecsHW supports GSM 850, E-GSM, GSM 900, GSM 1800 and GSM 1900 bandsMulti Band Capabilities (supporting of 850/1800 TRX, 850/1900TRX, and, 900 /1800 can be located in the same cabinet)All known A5 algorithms to be supported; HW provisions done
Standard Features due to new Architecture and new SW ReleasesSUS (Station Unit Sharing)Only one central control unit (SUM) for all BTS per cabinetMultiband BTS (GSM 900/1800) in one cabinetStatic (Release 4) and statistical (Release 6) submultiplexing on Abis
Better use of Abis-interface capacity: More BTS/TRX to be supported in a multidrop loopIntroduction of GPRS and HSCSD without HW changesEDGE compatible TRX
● The BTS range supports A5/1 and A5/2 ciphering algorithms;
● A5/0 = ‘no ciphering’ is always supported.
● The TRX are hardware ready for A5/3.
Section 1 · Module 1 · Page 253
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 253
2.9 Alcatel BSS
2.9.6 EVOLIUMTM BTS Features [cont.]
Features specific to Radio PerformanceTX Output Power (at TRX output)
RX Sensitivity: -111 dBm certified(GSM|ETSI| request: -104 dBm)
Synthesized Frequency Hopping as general solutionStandard RF hopping modePseudo baseband RF hopping mode
Antenna Diversity in generalTwo or four antennas (RX) per sectorTX Diversity feature is possible with Twin TRX module in coverage mode only.
Duplexer (TX and RX on one antenna) as general solutionMultiband capabilities
Thanks to the high flexibility of the EVOLIUM™ A9100 Base Station, GSM 850 and GSM 1800 TRXs or GSM 850 and GSM 1900 TRXs or GSM 900 and GSM 1800 TRXs or GSM 900 and GSM 1900 TRXs can be located in the same cabinet with a single Station Unit Module (SUM).
25 W = 44.0 dBm45 W = 46.5 dBmGSM 1900
30 W = 44.8 dBm60 W = 47.8 dBmGSM 1800 HP
30 W = 44.8 dBm35 W = 45.4 dBmGSM 1800 MP (*)
30 W = 44.8 dBm60 W = 47.8 dBmGSM 900 HP
30 W = 44.8 dBm45 W = 46.5 dBmGSM 900 MP (*)
15 W = 41.8 dBm45 W = 46.5 dBmGSM 850
TX output power, 8-PSK (EDGE)TX output power, GMSKFrequency band
(*) Note that for the Twin TRX, the TX output powers above are in capacity mode, i.e. each of the functional TRX achieves these output powers. In coverage mode, i.e. with Tx Diversity, a significant extra gain has to be considered (see "TX Diversity" chapter) thanks to on-air combining and diversity.
● The diagram below shows that 4RX Diversity requires two Antenna Network modules per sector, thereby needing either 4 vertical-polarized or 2 cross-polarized antennas.
Antenna NetworkAntenna Network
TX1 RX1
TX2RX3
RX20
RX4
TW IN
TRX
Figure : Twin TRX module in TX Div & 4 RX div
Section 1 · Module 1 · Page 254
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 254
2.9 Alcatel BSS
2.9.6 EVOLIUMTM BTS Features [cont.]
Capacity Mode Principle1 TWIN module = 2 functional TRX1 Housing = 2 functional TRX = 16 radio timeslotsSame Radio Performances as EDGE + TRX Medium Power
Reduced Power Consumption
Tx : GSM 900 : 45 W GMSK / 30 W 8PSKGSM 1800 : 35 W GMSK / 30 W 8PSK
Rx : Sensitivity < -114 dBm(-114 to -117 dBm with 2 Rx diversity – environment dependent)
Tx : GSM 900 : 45 W GMSK / 30 W 8PSKGSM 1800 : 35 W GMSK / 30 W 8PSK
Rx : Sensitivity < -114 dBm(-114 to -117 dBm with 2 Rx diversity – environment dependent)
Saving per TRX (vs. TRX EDGE+):- 17 % in GSM 900- 35 % in GSM 1800
Saving per TRX (vs. TRX EDGE+):- 17 % in GSM 900- 35 % in GSM 1800
2 TRXs can belongto different sectors
TRX1
TRX2
TRX
TRX
TRX
Section 1 · Module 1 · Page 255
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 255
Rx : Equ. sensitivity = -117.4 to - 121 dBm (*) (4RX div)(*) environment dependent)
Rx : Equ. sensitivity = -117.4 to - 121 dBm (*) (4RX div)(*) environment dependent)
Coverage Mode Principle
1 TWIN module = 1 functional TRX = 8 radio TS2 RX & 4 RX diversity possibleTX diversity used ( very high coverage)Gain in sites (less sites needed)This mode is also called TX div modeUp to 12 TRX in MBI5/MBO2 cabinets
Tx : GSM 900 : 113 to 175 W (*) GMSKGSM 1800 : 88 to 136 W (*) GMSK
Tx : GSM 900 : 113 to 175 W (*) GMSKGSM 1800 : 88 to 136 W (*) GMSK
Higher Output Power
Higher Sensitivity
2.9 Alcatel BSS
2.9.6 EVOLIUMTM BTS Features [cont.]
Section 1 · Module 1 · Page 256
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 256
2.9 Alcatel BSS
2.9.6 EVOLIUMTM BTS Features [cont.]
2 RX DiversityThe TRX module supports enhanced diversity combining in all frequency bands, which is based on several algorithms:A beam-forming algorithm to improve the received signal by steering a beam in the direction of the mobile. This is one way of doing smart antennas,An algorithm to reduce interference: this mitigates the influence of interferers by steering a null beam in the direction of the main interferer (the phase difference between the two antennas for the strongest interfering signal is estimated and then this interfering signal is strongly attenuated by summing the signals with an inversed phase).
-114.5dBm3.5 dBRural (RA100)
-116dBm5 dBSub Urban (TU50)
-117dBm6 dBDense Urban (TU3)
Equivalent RX sensitivity (without TMA)Total 2RX diversity gain
EnvironmentUser
strong interferer
Section 1 · Module 1 · Page 257
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 257
2.9 Alcatel BSS
2.9.6 EVOLIUMTM BTS Features [cont.]
4 RX Diversity4 RX diversity is supported by the Twin TRX module in coverage mode only. It uses exactly the same algorithms as for 2Rx diversity, i.e. beam-forming techniques are implemented. The table below provides the typical gains achieved thanks to 4RX enhanced Diversity and the equivalent Rx sensitivity that can be considered for link budget calculations.
4 RX diversity also provides significant benefits for GPRS/EDGE since it allows achieving higher throughputs for given radio conditions.
-117.4dBm6.4 dBRural (RA100)
-119.6dBm8.6 dBSub Urban (TU50)
-121dBm10 dBDense Urban (TU3)
Equivalent RX sensitivity (without TMA)Total 4RX diversity gain
Environment
Section 1 · Module 1 · Page 258
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 258
2.9 Alcatel BSS
2.9.7 Generic Configurations for A9100 G4/5 BTS
The configurations for indoor (MBI) and outdoor (MBO) cabinet are presented in the next slideslarger configurations with more than one cabinet can be derived from the tablesconfigurations are valid for EDGE capable TRX (Evolution step 2)availability of multiband configurations other than GSM 900 / GSM 1800 must be checked with product management (authorization required)Notation:
BBU - Battery Backup UnitBATS - Small Battery BackupLBBU - Large Battery Backup Unit
TWIN
TRX
TWIN
TRX
ANY
TWIN
TRX
TWIN
TRX
ANY
TWIN
TRX
TWIN
TRX
ANY
TWIN
TRX
TWIN
TRX
ANY
ANC
TWIN
TRX
TWIN
TRX
ANY
ANC
TWIN
TRX
TWIN
TRX
ANY
ANC
SUM
Mounting Frame for 19" equipment (3U) A//DC conversion
Ava
ilabl
e sp
ace
for e
ither
: • M
ount
ing
Fram
e
for 1
9" e
quip
men
t (6U
) • B
atte
ry
Ava
ilabl
e sp
ace
for e
ither
: • M
ount
ing
Fram
e
for 1
9" e
quip
men
t (6U
) • B
atte
ry
Stand
TWIN
TRX
TWIN
TRX
TWIN
TRX
TWIN
TRX
TWIN
TRX
TWIN
TRX
TWIN
TRX
TWIN
TRX
ANC
TWIN
TRX
TWIN
TRX
ANY
ANY
ANC
TWIN
TRX
TWIN
TRX
ANY
ANY
ANC
ANY
ANY
SUM
Indoor MBI5 3x8
Outdoor MBO2 3x8
Section 1 · Module 1 · Page 259
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 259
2.9 Alcatel BSS
2.9.8 Non multi-band configurations
900/1800 (2)2222213Low loss TX div & 4 RX div
900/1800 (2)22222222212Low loss TX div & 4 RX div
900/1800 (2)2222222222211Low loss TX div & 4 RX div
900/1800 (2)221222222113Standard TX div & 2 RX div
900/1800 (2)4211444422212Standard TX div & 2 RX div
900/1800 (2)4422444444411Standard TX div & 2 RX div
900/1800 (2)8866433Low-loss no TX div
900/1800 (2)126121010864332Low-loss no TX div
900/1800 (2)161264161616161210831Low-loss no TX div
900/1800 (2)* No BU5** MBO1 Evo. only
62**64442214Standard(3) no TX div
900/1800 (2)* No BU58421*864442213Standard(3) no TX div
900/1800 (2)8632888864412Standard(3) no TX div
900/1800 (2)8864888888811Standard(3) no TX div
Other BU5BU90other BU5
DCACDCACACACDCACAC
bandsMBO2Evolution
MBO1Evolut
ion
CBOMBI5 (Note 4)MBI3per sect.
FrequencyNotesMax TRX per sectorMin TRXSectors
Note 1: "AC other" is referring to the Indoor AC configurations without integrated battery, i.e. either with no battery, or with batteries in an external cabinet.Note 2: Frequency bands: new modules are available initially in GSM 900 and GSM 1800 frequency band; they will be available in a second step in GSM 850 and GSM 1900, on
market request.Note 3: As described in chapter "Standard configurations" above, "Standard" is referring to configurations with 1 Antenna Network per sector, and are thus limited to 8 TRXs per
sector. Configurations with more than 8 TRXs per sector need two Antenna Networks per sector; such configurations are called "Low-loss" and described in a separate section of the table.
Note 4: With MBI5, more than 18 TRX per cabinet is only possible with DC cabinets (and using TWIN modules) and more precisely with functional variant 3BK 25965 ABxx of these cabinets, that has become since end 2006 the standard delivery; MBI5 with functional variant 3BK 25965 AAxx, are limited to 18 TRX (using TWIN modules); functional variant of a cabinet can be checked either on site (on printed Barcode label, or available through Line Maintenance Terminal), or from the OMC-R where it is part of the Remote Inventory data.
Section 1 · Module 1 · Page 260
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 260
2.9 Alcatel BSS
2.9.9 Multi-band configurations
900/1800 (2)4/44/42/22/22/21/13Standard no TX div
900/1800 (2)6/62/26/64/44/44/41/12Standard no TX div
900/1800 (2)12/126/64/22/212/128/88/88/86/62/22/21/11Standard no TX div
Other BU5BU90other
BU5
DCACDCACACACDCACAC
bandsMBO2Evolution
MBO1EvolutionCBOMBI5 (Note 4)MBI3
per sect.band1/band2
(3)
FrequencyNotesMax TRX per sector (band 1/ band 2)Min TRXSectors
Note 1: "AC other" is referring to the Indoor AC configurations without integrated battery, i.e. either with no battery, or with batteries in an external cabinet.Note 2: Frequency bands: new modules are available initially in GSM 900 and GSM 1800 frequency band; they will be available in a second step in GSM 850 and
GSM 1900, on market request.Note 3: Count of sectors is made with hypothese of multiband cell, i.e. that each sector contains one cell in band1 and one cell in band2, these two cells being paired
as a single "multiband cell", counted as one sector.In multiband "without multiband cell", a same configurations would be counted as having twice the number of sectors.The table above thus describes at the same time- possible configurations for multiband "with multiband cell"- those configurations for multiband "without multiband cell" that have the same number of sectors in each band
Note 4: With MBI5, more than 18 TRX per cabinet is only possible with DC cabinets (and using Twin TRX modules) and more precisely with functional variant 3BK 25965 ABxx of these cabinets, that has become since end 2006 the standard delivery; MBI5 with functional variant 3BK 25965 AAxx, are limited to 18 TRX (using Twin TRX modules); functional variant of a cabinet can be checked either on site (on printed Barcode label, or available through Line Maintenance Terminal), or from the OMC-R where it is part of the Remote Inventory data.
Section 1 · Module 1 · Page 261
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 261
2.9 Alcatel BSS
2.9.10 Extended cell configurations
900MBI3; MBO1 Evolution4411
900MBI5; MBO2 evolution8811
OuterInnerOuterInner
Frequency band
Type of cabinetof TRXMax. numberof TRXMin. Number
Extended Cell configurations
Section 1 · Module 1 · Page 262
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 262
2.9 Alcatel BSS
2.9.11 Standard configurations
1 up to2TRX/ sector
No-combining ANC or ANB
Antenna Antenna
TRX 1 TRX 2
3 up to 4TRX/ sector
Antenna Antenna
TRX 1 TRX 4
Combining ANC
5 up to 6TRX/ sector 5 up to 8RX/sector
TRX 1TRX 2
Combining ANC
Antenna Antenna
TRX 3 TRX 6
Combiner (ANY)
TRX 1 TRX 4
Combining ANC
Antenna Antenna
TRX 5 TRX 8
Combiner (ANY) Combiner (ANY)
The interface with the antenna system is through one single Antenna network combining (ANC) module in each sector (and then through 2 feeders and two antennas or one dual-polarized antenna).
Standard configurations with Twin TRX in No TX Div
The number of sectors and TRXs depends on the cabinet type, with a maximum of 6 sectors and 24 TRXs in a Indoor MBI5 ("AB" functional variant) or an Outdoor MBO2 evolution cabinet.
Section 1 · Module 1 · Page 263
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 263
2.9 Alcatel BSS
2.9.12 TRX Types
44,830W45,435W1800TGT18
44,830W46,545W900TGT09
44,830W46,860WHP1800TADHE
44,025W47,760WHP1800TADH
47,760WHP1800TRDH
40,025W46,545WMP1900TRAP
44,830W45,435WMP1800TRADE
40,812W45,435WMP1800TRAD
41,830W47,860WHP900TAGHE
44,025W47,760WHP900TAGH
44,830W46,545WMP900TRAGE
41,815W46,545WMP900TRAG
41,815W46,545WMP850TRAL
dBmWdBmW
8PSKGMSKPOWERBANDNAME
Example of TRE boards with their frequency band and power characteristics
GMSK – Gaussian Minimum Shift Keying
8PSK – 8 phase shift keying
TGT – Twin GSM Tranceiver
Different Transceivers are used depending on the band : 900, 1800, 1900 (in America) and 850MHz (this new band has been introduced in the Release 1999 of the 3GPP Standard).
The list above is not exhaustive.
A new Tx Rx hardware module gives the possibility to have per Hardware module transmission receiption function. In this case the module is called Twin TRX
For example
In the MBI5 rack, the number of hardware module is 12 maximum, but if all are Twin TRX the maximum number of Transmitter functions will be 24. (TRE G5)
The new Twin TRX (TGT) gives also the possibility to provide TX diversity
Section 1 · Module 1 · Page 264
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 264
2.9 Alcatel BSS
2.9.12 TRX Types
The losses between TRE connector and the Antenna connector
Configuration Transmission loss (dB)
1 ANC without bridges 1.8
1 ANC 5.1
1 ANC + 1 ANY 8.6
1 ANX 1.8
1 ANX / 1 ANY 5.3
1 ANX + 2 ANY 8.8
delta ANY 3.5
Module Transmission loss (dB)
ANC 4.4
ANC no bridge 1
ANX 1
ANY 3.3
Radio cables
TRE-AN
AN-AN
AN-Antenna
0.3
0.2
0.5
Losses due to the Antenna Network (AN)
Section 1 · Module 1 · Page 265
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 265
2.9 Alcatel BSS
2.9.13 BTS Output Power
What is monitored during validation is the BTS output power at antenna connectorThe individual losses for duplexer, combiner and internal cabling are not systematically measuredfor detailed info consult the BTS product description
Section 1 · Module 1 · Page 266
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 266
2.9 Alcatel BSS
2.9.14 Feature Power Balancing
From G4 (now G5) BTS it is allowed to use TRXs of different power within the same sector, or to use of different combining path for TRX belonging to the same sector. Reason: the G4 BTS is able to detect unbalanced losses/powers within a sector and automatically compensate it for GMSK modulation.Consequence: All TRX connected to one ANc are automatically adjusted to the GMSK output power of the weakest TRX (required for BCCH recovery)
Section 1 · Module 1 · Page 267
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 267
2.9 Alcatel BSS
2.9.15 Cell Split Feature
PrincipleCell Split allows to provide one logical cell with one common BCCH over several BTS cabinets. The cabinets must be synchronized
BenefitsSame number of TRX in fewer racksNo need to touch/modify the configuration of existing BTS (cabling)Take full benefit of 24 TRX per cabinet
Drawback: more complex antenna systemApplications
Multi-band cells Configuration extension of sites by adding TRX Large configurations
Condition: BTS must be synchronized
Configuration built with several cabinets and the “cell split over two BTSs” featureIt is possible to optimize the number of cabinets needed for a site configuration (indoor or outdoor, single
band or multi-band) built with more than one cabinet, thanks to a feature called “cell split over two BTSs”.
In that case, the TRXs of one sector can be split over two A9100 BTS cabinets. Various configurations are possible, the only constraint being that following conditions are fulfilled:
Maximal number of TRX per cell is 16.
Maximal number of cabinets between which a given cell is shared is 2.
Cabinets between which a cell is shared are clock synchronised in a master / slave configuration
Note : when used in mono band configurations, cell split feature may allow to reduce the number of cabinets with regards to the solution with one cabinet per sector; but at the expense of a more complex antenna system (two ANC, hence 4 feeders per sector instead of 2 feeders, as for "low-loss" configurations); this has to be considered before selecting such a solution.
Section 1 · Module 1 · Page 268
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 268
2.9 Alcatel BSS
2.9.19 Cell Split Example: High Power Configuration
Cabinet1 (Standard 8,8,8TRX)
Cabinet2 (Standard 8,8,8TRX)
Sector3: 1x16 TRX Sector2: 1x16 TRX Sector1: 1x16 TRX
TRX 1 TRX 4
ANC
TRX 5 TRX 8
ANY ANY
TRX 1 TRX 4
ANC
TRX 5 TRX 8
ANY ANY
TRX 1 TRX 4
ANC
TRX 5 TRX 8
ANY ANY
TRX 1 TRX 4
ANC
TRX 5 TRX 8
ANY ANY
TRX 1 TRX 4
ANC
TRX 5 TRX 8
ANY ANY
TRX 1 TRX 4
ANC
TRX 5 TRX 8
ANY ANY
The following figure gives an example of standard multi-band with multi-band cell 3x8/3x8 in 2 MBI5 cabinets :
For a MBI5, in a 3 sector configuration, max. 3 HP TRX /sector are allowed (thermal reasons).
The only way´to have 3x6 in MBI5 is with the cell split feature.
Section 1 · Module 1 · Page 269
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 269
2.9 Alcatel BSS
2.9.22 Indoor BTS Rack Layout
IND mini: 4carrier, 1 Duplexer (Anx), 1 Combiner (Any), SUM (CPU, Link to BSC)
IND Medi: 12carrier, 3 Duplexer (Anx), 3 Combiner (Any), SUM (CPU, Link to BSC)
Section 1 · Module 1 · Page 270
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 270
2.9 Alcatel BSS
2.9.23 Outdoor MBO1 Evolution and MBO2 Evolution cabinets
Mounting Frame for 19" equipment (3U) A//DC conversion
Ava
ilabl
e sp
ace
for e
ither
: • M
ount
ing
Fram
e
for 1
9" e
quip
men
t (6U
) • B
atte
ry
Avai
labl
e sp
ace
for e
ither
: • M
ount
ing
Fram
e
for 1
9" e
quip
men
t (6U
) • B
atte
ry
Radio subrack
Radio subrack
Radio subrack
Radio subrack
Radio subrack
Radio subrack
156 cm94 cmWidth
161 cm161 cmHeight with plinth
146 cm146 cmHeight without plintht
80 cm80 cmDepth (roof level)
74 cm74 cmDepth (floor level)
MBO2Evolution
MBO1Evolution
External Dimensions
The Multi-standard Outdoor BaseStation cabinets MBO1 Evolution and MBO2 Evolution offer operators important flexibility with:
An easy extension on-site from the Outdoor MBO1 Evolution BTS (up to 12 TRXs capacity) to the Outdoor MBO2 Evolution BTS (up to 24 TRXs capacity)
Section 1 · Module 1 · Page 271
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
13
14
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 271
2.9 Alcatel BSS
2.9.24 Micro BTS types
M5M EVOLIUM A9110 Micro-BTS (M5M)
Introduced in Q3 2003
up to 12 TRX-es
site configurations can mix older A910 with newer A9110-E
support for GPRS and EDGE (release dependent)
Section 1 · Module 1 · Page 272
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 272
2.9 Alcatel BSS
2.9.25 Technical Data
A910(2 TRX)
A9110(2 TRX)
Frequency band GSM 850, E-GSM,GSM900, GSM 1800, GSM
1900
GSM 850, E-GSM,GSM900, GSM 1800, GSM
1900Tx output power(at antenna connector)
Up to 4.5 W 7 W
Rx sensitivity -107 dBm -110 dBm
Radio FH Yes yes
Temperature range (max.) 55 °C 55 °C
Max. power consumption 130 W 145 W
Size (volume) 54 litres 54 litres
Weight 39.6 kg (incl. connectionbox)
32.5
Section 1 · Module 1 · Page 273
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 273
2.9 Alcatel BSS
2.9.26 BSC capacities in terms of boards
Three BSC capacities are defined depending on the number of TRXs
200 TRX 400 TRX 600 TRX
BSC Capacity
ATCA shelf
CCP
Spare CCP
TPGSM
OMCP
SSW
LIU shelf
MUX
LIU
1 2 3
1
1
2
2
2
1
2
8 16
Equipment
The quantity of TPGSM, OMCP, SSW and MUX boards have to be considered as 1 activ + 1 stand-by for redundancy function in the shelf.
LIU Line Interface Unit – 16x 2Mbit/Board
Section 1 · Module 1 · Page 274
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 274
2.9 Alcatel BSS
2.9.27 Capacity and dimensioning for E1 links
The BSC Evolution is able to process up to 2600 erlangs
200 TRX 400 TRX 600 TRX
BSC Capacity
Max number of BTS
Max number of cells
Total number of E1
Number of Abis
Number of Atermux CS
Number of Erlangs
Traffic Ater PS (Mb/s) Max
255
Equipment
Number of Atermux PS
264
224
176
30
18
2600
36
255
264
128
96
20
12
1800
24
150
200
112
96
10
6
900
12
Section 1 · Module 1 · Page 275
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 275
2.9 Alcatel BSS
2.9.28 Abis and atermux allocation on LIU boards
Abis and atermux allocation on LIU boards versus BSC capacity
200 TRXLIU 1 LIU 2 LIU 3 LIU 4 LIU 5 LIU 6 LIU 7 LIU 8 LIU 9 LIU 10 LIU 11 LIU 12 LIU 13 LIU 14 LIU 15 LIU 16
1 1 17 33 49 65 81 97 113 129 145 161 41 31 21 2 12 2 18 34 50 66 82 98 114 130 145 162 42 32 22 4 33 3 19 35 51 67 83 99 115 131 147 163 43 33 23 6 54 4 20 36 52 68 84 100 116 132 148 164 44 34 24 8 75 5 21 37 53 69 85 101 117 133 149 165 45 35 25 10 96 6 22 38 54 70 86 102 118 134 150 166 46 36 26 12 117 7 23 39 55 71 87 103 119 135 151 167 47 37 27 14 138 8 24 40 56 72 88 104 120 136 152 168 48 38 28 16 159 9 25 41 57 73 89 105 121 137 153 169 x 39 29 18 17
10 10 26 42 58 74 90 106 122 138 154 170 x 40 30 20 1911 11 27 43 59 75 91 107 123 139 155 171 x 24 18 12 1112 12 28 44 60 76 92 108 124 140 156 172 x 23 17 10 913 13 29 45 61 77 93 109 125 141 157 173 28 22 16 8 714 14 30 46 62 78 94 110 126 142 158 174 27 21 15 6 515 15 31 47 63 79 95 111 127 143 159 175 26 20 14 4 316 16 32 48 64 80 96 112 128 144 160 176 25 19 13 2 1
Abis ports (max 176)Atermux CS (max 48)Ater mux PS (max 28)
200 TRX400 TRX 400 TRX
600 TRX 600 TRX
200
400
400
200
Abis ports Ater Ports
One ater LIU boardfor 200 TRX
Maximum flexibilityon abis LIU board
LIU boards are fitted in the LIU shelf depending on the BSC configuration (Capacity + connectivity), but
only 2 HW configurations for the LIU shelf are considered: one with 8 LIU boards, one with 16 LIU boards,
Assignment to each LIU boards either to Abis or Ater,
On the Ater LIU, 10 TP are “generic” (can be assigned either to PS, full CS or a mixed of the 2), and the 6 others are dedicated to PS.
In case of 200 TRX configuration, Alcatel decided to split the traffic up to 2 LIU boards (even if one LIU board should be efficient) in order to not impact all the traffic in case of one LIU board failure.
The maximum of available LIU boards are used for Abis, to offer maximum flexibility to the clients.
The port numbered 9, 10, 11 and 12 on the LIU 12 are not used.
Section 1 · Module 1 · Page 276
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 276
2 Coverage Planning
2.10 Coveradge Improvement
Section 1 · Module 1 · Page 277
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 277
2.10 Coveradge Improvement
2.10.1 Antenna Diversity
Section 1 · Module 1 · Page 278
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 278
2.10.1 Antenna Diversity
2.10.1.1 Diversity
PurposeImprovement in fading probability statistics
leads to a better total signal level or better total S/N ratio
PrincipleCombining signals with same information from different signal branches
Demandscorrelation between different signal branches should be low
Combining methodsSelection DiversityMaximum Ratio CombiningEqual Gain Combining
PurposeThe purpose of using diversity is to reduce short-term fading effects, such that an acceptable level of
performance (receiver sensitivity) can be achieved, without having to increase the transmitted power or the bandwidth.
PrincipleThe principle relies on the combination of two or more signals, containing the same information, which are at
least partially de-correlated. If two signals of the same level are completely de-correlated, the probability that both signals experience the same depth of fade is very low. Therefore the signal reliability is increased.
Section 1 · Module 1 · Page 279
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 279
Time [sec]
Field
stre
ng
th[d
Bm
]
0.1 0.2 0.3 0.4
-80
-90
-100
Antenna 1 Antenna 2
2.10.1 Antenna Diversity
2.10.1.2 Selection Diversity (1)
Principleselection of the highest basebandsignal-to-noise ratio (S/N) or of the strongest signal (S+N)
Correlation of signal levelsa lower correlation between signal levels of different branches improves the total signal levelCorrelation of signal levels should
be low
The algorithm for the selective diversity combining technique is based on the principle of selecting the best signal among all of the signals received from different branches, at the receiving end.
Section 1 · Module 1 · Page 280
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 280
Time [sec]
Field
stre
ng
th[d
Bm
]
0.1 0.2 0.3 0.4
-80
-90
-100
Antenna 1
Antenna 2
2.10.1 Antenna Diversity
2.10.1.3 Selection Diversity (2)
Difference in signal levela high difference in signal levels of two branches doesn’t improve the total signal levelDifference in signal levels should
be low
Section 1 · Module 1 · Page 281
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 281
2.10.1 Antenna Diversity
2.10.1.4 Selection Diversity (3)
Theoretical diversity gain10dB for two-branch diversity at the 99% reliability level16dB for four branches at the 99% reliability levelThe theoretical diversity gain
doesn’t improve linear with the number of branches
Section 1 · Module 1 · Page 282
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
In comparison with MRC, in this technique the branch weights are all set to unity but the signal from each branch are co-phased to provide equal gain combining diversity.
The possibility of producing an acceptable signal from a number of unacceptable inputs is still retained, and performance is only marginally inferior to maximal ratio combining an superior to selection diversity.
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 282
2.10.1 Antenna Diversity
2.10.1.5 Equal Gain Combining (1)
Principlecophase signal branchessum up signalsCoherent addition of signals and
incoherent addition of noisesTheoretical diversity gain
11dB for two-branch diversity at the 99% reliability level
Section 1 · Module 1 · Page 283
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 283
2.10.1 Antenna Diversity
2.10.1.6 Equal Gain Combining (2)
Difference in signal levelAssuming equal noise in the branches, the higher the difference in signal levels is, the higher is the loss of S/N ratio of the better signal branch after summationDifference in signal levels should
be low
Correlation of signal levelsa lower correlation between signal levels of different branches improves the total S/N ratioCorrelation of signal levels should
be low
Section 1 · Module 1 · Page 284
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 284
2.10.1 Antenna Diversity
2.10.1.7 Maximum Ratio Combining (1)
Principleweight signals proportionally to their S/N ratioscophase signal branchessum up the weighted signalsCoherent addition of signals and
incoherent addition of noisesImproved S/N
In this method the signals from all the branches are weighted according to their individual S/N and then summed. Here the individual signals must be co-phased before being summed ( unlike selection diversity ) which generally requires an individual receiver and phasing circuit for each antenna .
Maximal ratio combining produces an output SNR equal to the sum of the individual SNRs. Thus, it has the advantage of producing an output with an acceptable SNR even when none of the individual signals are themselves acceptable.
This technique gives the best statistical reduction of fading of any known diversity combiner. Modern DSPs and digital receivers are now making this optimal form of diversity practical.
Section 1 · Module 1 · Page 285
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 285
Correlation of signal levelsa lower correlation between signal levels of different branches improves the total S/N ratioCorrelation of signal levels should
be low
2.10.1 Antenna Diversity
2.10.1.8 Maximum Ratio Combining (2)
Difference in signal levelAssuming equal noise in the branches, the higher the difference in signal levels is, the higher is the loss of S/N ratio of the better signal branch after summationcomparing to equal ratio combining, this combining reduces influence of worse signal branchesDifference in signal levels should be
low
Section 1 · Module 1 · Page 286
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 286
2.10.1 Antenna Diversity
2.10.1.9 Comparison of combining methods
Improvement of average SNR from a diversity combiner compared to one branch
(a) Maximum Ratio Combining(b) Equal Gain Combining(c) Selection DiversityThe maximum ratio combining,
which is used in the ALCATEL BTS, gives the best statistical reduction of any known linear diversity combiner.
Section 1 · Module 1 · Page 287
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 287
2.10.1 Antenna Diversity
2.10.1.10 Enhanced Diversity Combining (1)
Principle: 2 algorithms
Beam forming algorithm (available also for MRC)Interference reduction algorithm (new)
best efficiency when the useful signal and the interfering signals come from different directions.
Requirements to benefit from this feature:Hardware: G4 (onwards) TRE (Edge capable TRX) installed in EvoliumEvolution BTS step1 resp. step 2 (internal name: G3 resp. G4)Software release: from B6.2 onwardsFor a maximum gain: antenna engineering rules respected
Correct antenna choice for the considered environmentCorrect antenna spacings and orientations (in case of space diversity)
The TRX module supports enhanced diversity combining in all frequency bands, which is based on several algorithms:
● A beam-forming algorithm to improve the received signal by steering a beam in the direction of the mobile. This is one way of doing smart antennas,
● An algorithm to reduce interference: this mitigates the influence of interferers by steering a null beam in the direction of the main interferer (the phase difference between the two antennas for the strongest interfering signal is estimated and then this interfering signal is strongly attenuated by summing the signals with an inversed phase).
Maximum efficiency of enhanced diversity combining is achieved when the useful/desired signal and the interfering signals emanate from different directions. In interference-limited environments, beam-forming algorithms will provide a much greater diversity gain compared to traditional maximum ratio combining.
● The above mentioned algorithms are working together in a way to combat spatial interferer signals while keeping optimal sensitivity perfomance for undisturbed but week reception.
Section 1 · Module 1 · Page 288
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 288
2.10.1 Antenna Diversity
2.10.1.11 Enhanced Diversity Combining (2)
-114.5dBm3.5 dBRural (RA100)
-116dBm5 dBSub Urban (TU50)
-117dBm6 dBDense Urban (TU3)
Equivalent RX sensitivity (without TMA)Total 2RX diversity gain
Environment
Diversity gain coming from the fact that the signals received on both antennas are de-correlated (this requires using Xpol antennas or largely spaced antennas)
Array-Gain or Beamforming gain : coming from the fact, that co-phased signals are added (stronger combined signal power) for this direction
Null Steering / Interference Reduction (with a spatial interferer) coming from a algorithm which reduces the interference (the figures below assume a standard interference margin is considered for the link budget)
Section 1 · Module 1 · Page 289
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 289
2.10.1 Antenna Diversity
2.10.1.12 Tx Diversity
GSM900: 50.5dBm (113W)GSM1800: 49.4dBm (88W)
4 dBRural (RA100)
GSM900: 51.1dBm (129W)GSM1800: 50dBm (100W)
4.6 dBSub Urban (TU50)
GSM900: 52.4dBm (175W)GSM1800: 51.3dBm (136W)
5.9 dBDense Urban (TU3)
Equivalent TX output power (GMSK)Total TX diversity gain
Environment
Basic Idea:Transmit twice the same signal from two antennasNo combining losses (on air combining)
3dB gain
Possible Issue:Coherence between signal can lead to destructive effectsThis effect depends on the environment
a short delay is introduced between two antennas (2 symbols)
BTS MS
0011000101001
0011000101001
short delay
TX Diversity works with all types of Mobile stations since it is fully transparent to the receiver; this feature takes advantage of the MS equalizer which can already handle multiple paths with different times of
arrival.
Consequently, the equivalent TX output power is very high, up to 6dB above the nominal TX output power, which improves the coverage and reduces the number of sites needed to cover a given area, provided the link budget remains balanced or downlink-limited
The table provides the typical gains achieved thanks to TX Diversity and the equivalent TX output power that can be considered for link budget calculations. Note that such gains are environment-dependent
since they are highly related to the level of de-correlation between paths.
In 8-PSK, the TX diversity gain is highly dependent on the coding scheme, the environment and the level of Carrier to Interference+Noise Ratio. No significant gains are expected.
Section 1 · Module 1 · Page 290
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 290
2.10.1 Antenna Diversity
2.10.1.12 Tx Diversity
Diversity Gain:On top of the output power increaseTxDiv artificially increases the number of multi-pathsThe higher the de-correlation between paths, the higher the gainOther features: a) high power TRX or b) Transmit Coherent Combining do not benefit from this effect
First channel
Second channel
Time
Attenuation
Fading hole
Example:2 paths (blue and red)They show independent amplitude (fast) fadingProbability to fall in a hole is reducedFading holes of a channel are often compensated by the other channel
Additional gain
Section 1 · Module 1 · Page 291
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 291
2.10.1 Antenna Diversity
2.10.1.12 Tx Diversity
Delay Trade-Off
Higher delay between antennas impliesLess destructive effect, more de-correlated paths and so higher diversity gain: Higher GainsHigher channel delay spread: More Self-interference
Alcatel found the optimal trade-off • For all environments• Based on extensive simulations and lab measurements
0011000101001
0011000101001
short delay
Section 1 · Module 1 · Page 292
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 292
2.10.1 Antenna Diversity
2.10.1.12 Tx Diversity
Summary of the Transmit Diversity effects3dB increase of the signal strengthAdditional up to 2.9dB diversity gain for un-correlated fast fading:
Diversity gains are maximum in dense urban because there are a lot of scatterersDiversity gains are reduced in rural because we have Line of Sight propagation
Self-interference due to the artificial increase of the delay spread
Environment Fading Profile
Power increase
Diversity gain
Total TxDivgain
Dense Urban TU3 3dB 2.9dB 5.9dB
Sub-Urban TU50 3dB 1.6dB 4.6dB
Rural RA100 3dB 1dB 4dB
Section 1 · Module 1 · Page 293
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 293
2.10.1 Antenna Diversity
2.10.1.12 Diversity systems in Mobile Radio Networks
Two diversity systems are used in Mobile Radio Networks :Space DiversitySpace Diversity
horizontalvertical
PolarizationPolarization DiversityDiversity
dH
RXA RXB
+45° -45°
RXA RXB
dH
TXA TXB
+45° -45°
TXA TXB
TXA
TXB
dv
Section 1 · Module 1 · Page 294
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 294
2.10.1 Antenna Diversity
2.10.1.13 Space Diversity Systems
Diversity gain depends on spatial separation of antennas
dH
RXA RXB
dV
RXA
RXB
Horizontal separation(e.g. Roof Top)
Vertical separation(e.g. Mast)
For Optimum Diversity GaindH = 20λ dV =
15λGSM900 = 6m GSM900 = 4.5mGSM1800 = 3m GSM1800 = 2.25m
Section 1 · Module 1 · Page 295
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 295
The larger the separation the higher the diversity gainPrefer horizontal separation (more effective)The higher the antenna the higher the requiredseparation, rule: d > h/10
Highest diversity gain from the "broadside”Select orientation of diversity setup according to orientation of cell
/ traffic
h
d
Optimum diversity Gain
2.10.1 Antenna Diversity
2.10.1.14 Space Diversity - General Rules
Section 1 · Module 1 · Page 296
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 296
2.10.1 Antenna Diversity
2.10.1.15 Achievable Diversity Gain
Depends on fading conditionsVaries in between 2.5 - 6dBHigher diversity gain in areas with multipath propagation (urban and suburban areas)
General rule: consider diversity gain with 3dB in the link budget
Section 1 · Module 1 · Page 297
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 297
Horizontal / vertical polarization:Hor/Ver Antenna
Polarization of +/- 45°:cross polarized antennaor Slant antenna
Big Advantage: Only one panel antenna is required to profit from diversity gain using this configuration
V H +45° -45°
RXA RXB RXA RXB
2.10.1 Antenna Diversity
2.10.1.16 Polarization Diversity
Diversity gain in using orthogonal orientated antennas
Section 1 · Module 1 · Page 298
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 298
DiversityGain
multipath-propagation
reflection,diffraction
reception with
reception with
a hor / verpolarisedantenna
a X-polarisedantenna
EV
EH
EX2
EX1
G = f( ρ,Δ )
Time [sec]
Ex1 or Ev
Ex2 or Eh
2.10.1 Antenna Diversity
2.10.1.17 Principle of Polarization Diversity
ρ correlation coeficient (0.7)
Δ difference in signal level
---> diversity gain with dual polarized antennas depends on :
ρ, Δ and the orientation of the sending and receiving antenna
To achieve low correlation and low differences in signal level, reflection and diffraction under multipath condition is necessary. ---->
In rural areas neglectible diversity gain can be expected from polarization diversity.
Section 1 · Module 1 · Page 299
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 299
2.10.1 Antenna Diversity
2.10.1.18 Air Combining
Featuresonly one TX per antennacombining signals "on air" and not in a combiner3dB combiner loss can be saved to increase coverage
Can be realized with two vertical polarized antennasone cross polarized panel antenna
TX1 TX2
TX1 TX2
The idea of air combining is to combine transmitted signals in the air and not with an internal combiner, in order to save combining losses. Thus the maximum achievable coverage range will be increased.
Air combining can be realized with• two sector or omni antennas• one cross polar antenna transmitting different carriers on +/-45°.
Section 1 · Module 1 · Page 300
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 300
2.10.1 Antenna Diversity
2.10.1.19 Air Combining with Polarization Diversity
One antenna systemcross polarized antennas recommended for urban/suburban area (less space req.)
No Air combiningBandfilter if De-coupling too low
Air combiningRecommended forEvolium BTS
V H
DUPL BF
TX RXA RXB
DUPL
TX1 RX1 TX2 RX2RX2D RX1D
DUPL
or
1 TRX 2 TRX
Section 1 · Module 1 · Page 301
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 301
2.10.1 Antenna Diversity
2.10.1.20 Air Combining with Space Diversity
Two antenna systemVertical or horizontal spacing (recommended for rural area)
RXA RXB TX
or or
RXARXB
TX
Section 1 · Module 1 · Page 302
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 302
2.10.1 Antenna Diversity
2.10.1.21 Decoupling of Signal Branches
One antenna system: TX / RX decoupling cannot be achieved by spatial separationDecoupling between both polarization branches needs to be sufficiently high to avoid
blocking problemsintermodulation problems
Required decoupling valuesG2 BTS: 30 dBEvolium A9100 BTS: 25dB (Integrated duplexer Anx)
Section 1 · Module 1 · Page 303
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 303
2.10.1 Antenna Diversity
2.10.1.22 Cross Polarized or Hor/Ver Antenna? (1)
Receiving Applicationsame diversity gain for cross polarized and hor/ver antennasin urban and suburban area polarization diversity gainpolarization diversity gain equal to space space diversity gaindiversity gain (2.5 - 6dB)negligible polarization diversity gain polarization diversity gain in rural areas (not recommended)accordingly consider polarization diversity gainpolarization diversity gain with 3dB in the link budget
Section 1 · Module 1 · Page 304
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 304
2.10.1 Antenna Diversity
2.10.1.23 Cross Polarized or Hor/Ver Antenna? (2)
Transmission Application: Air combining
3dB loss when transmitting horizontal/vertical polarized (use of combiner)1-2dB losses when transmitting at 45°(optimum antenna is straighten vertically)Air combining only recommended with cross polarized antenna
3dB2dB
Section 1 · Module 1 · Page 305
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 305
2.10.1 Antenna Diversity
2.10.1.24 Conclusion on Antenna Diversity
Rural Areasinstallation space not limitedapply Space Diversity (higher gain)
Urban and Suburban Areaapply space or polarization diversityuse cross polarized antennas for air combining
Diversity Gainconsider diversity gain in link budget with 3dB
Section 1 · Module 1 · Page 306
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 306
2.10. Coveradge Improvement
2.10.2 Repeater Systems
Section 1 · Module 1 · Page 307
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 307
2.10.2 Repeater Systems
2.10.2.1 Repeater Application
BTS (donor cell)repeater
original service areaarea covered by repeater
Section 1 · Module 1 · Page 308
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 308
2.10.2 Repeater Systems
2.10.2.2 Repeater Block Diagram
Required Isolation > 70…90 dB
A repeater is a bi-directional amplifier. It receives the downlink signal from the BTS, amplifies it and transmits the signal to the mobile. In the uplink direction, the signal of the mobile is received, amplified and transmitted to the BTS.
Section 1 · Module 1 · Page 309
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 309
2.10.2 Repeater Systems
2.10.2.3 Repeater Applications (2)
Coverage Improvement of Cells (‘Cell Enhancer’)removal of coverage holes caused by
topography (hills, ravines, ...)man made obstacles
Provision of tunnel coveragestreet, railway tunnelsunderground stations
Provision of indoor coverage at places of low additional traffic
Section 1 · Module 1 · Page 310
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 310
2.10.2 Repeater Systems
2.10.2.4 Repeater Types
Channel selective repeatershigh selectivity of certain channelshigh traffic areas, small cell sizes
Band selective repeatersadjustment to operator’s frequency bandno (accidental) usage by competitors
Broad band repeaterslow cost solution for low traffic areas (rural environment)medium to high repeater gain
Personal repeaterslow gainbroad bandindoor coverage improvement for certain rooms
Section 1 · Module 1 · Page 311
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 311
Antennato donor cell
Repeater
Radiatingcable
Tunnel
2.10.2 Repeater Systems
2.10.2.5 Repeater for Tunnel Coverage
Choice of repeater type due totunnel dimensionswall materials
feeding bydirectional antennasleaky feeder cables
long tunnelschains of several repeatersfiber optic backbone for repeater feeding
Section 1 · Module 1 · Page 312
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 312
Personal repeater
Antennatodonor cell
Fiber opticdistribution
Remoteunits
Master unit
Radiatingcable
2.10.2 Repeater Systems
2.10.2.4 Repeater for Indoor coverage
For smaller buildingsCompensation for wall losses, window losses (heat insulated windows)Low cost personal repeaters installed in certain rooms
For larger buildings (shopping malls, convention centers, sport centers)
multispot transmission usingco-axial distribution networkfiber-optic distribution network
Section 1 · Module 1 · Page 313
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 313
2.10.2 Repeater Systems
2.10.2.5 Planning Aspects
Repeater does not provide additional traffic capacityrisk of blocking if additional coverage area catches more traffic
possible carrier upgrading requiredRepeater causes additional signal delay
delay: 4..8μs ⌫ max. cell range of 35 km reduced by 1 to 2kmspecial care needed for total delay of repeater chain!delayed signal and original signal could cause outage in urban environment if total delay exceeds 16 ... 22μs
Section 1 · Module 1 · Page 314
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 314
2.10.2 Repeater Systems
2.10.2.6 Repeater Gain Limitation (1)
Intermodulation products should be lowwhen amplifier reaches saturation point, intermodulation products go up
Signal to noise ratio should be highwhen amplifier reaches saturation point, signal to noise ratio is getting worse
Antenna isolation between transmission and receiving antenna should be high
if signal feedback from transmission antenna to receiving antenna is too high, amplifier goes into saturation
Section 1 · Module 1 · Page 315
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 315
2.10.2 Repeater Systems
2.10.2.7 Repeater Gain Limitation (2)
Pin Poutgain78 dB
isolation90 dB
Pback =Pin - 12 dB
Repeater gain limited by antenna isolation:
GRepeater < IDonor, Repeater - M M (Margin) ~ 12 dB
Measure isolation after installation
inMAmplifierGI argδ+=
Section 1 · Module 1 · Page 316
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 316
2.10.2 Repeater Systems
2.10.2.8 Intermodulation Products
A Non-linear systemproduces higher-order intermodulation products as soon as output power reaches the saturation point
Parameter1 dB compression point3rd order intercept point (ICP3)Intermodulation reduction (IMR)Amplifier back-off
GSM900/GSM1800 requirementsIM products ≤ -36 dBm or IM distance > 70 dBc whichever is higher
Each amplifier has a limited linear operation range.
In the linear range the input power is amplified by the amplification factor v. But this is only valid until a certain maximum input power. As soon as you feed the amplifier with too high input power the input signal will less and less amplified. The point were the degradation from the specified amplification is 1dB is called the one dB compression point.
Lower amplification is one effect when you operate an amplifier in the non linear region, another effect which can cause even worse problems is the intermodulation. Especially the 3rd order intermodulationproduct (2f1+-f2) is very significant. The amplifier produces interfering signals based on available frequencies (f1 and f2).
dbc = is the power of one signal referenced to a carrier signal
Section 1 · Module 1 · Page 317
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 317
Uplink Loss = Downlink Loss ⇒ Uplink Gain = Downlink Gain!
2.10.2 Repeater Systems
2.10.2.9 Repeater Link Budget
Different gains may be needed in Up- and Downlink if the sensitivity of the repeater is worse than the sensitivity of the BTS
!
Downlink Path Unit ValueReceived power at repeater dBm -65Link antenna gain dBi +19Cable loss dB -2Repeater input power dBm -48Repeater gain dB +78Repeater output power dBm 30Cable loss dB -2Repeater antenna gain dBi +18EIRP dBm 46
Section 1 · Module 1 · Page 318
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 318
2.10.2 Repeater Systems
2.10.2.10 High Power TRXs
High Power TRXs: solution for coverage improvementHP must be used together with TMA: due to unbalanced Link BudgetA9100 BTS supports
High Power TRXMedium Power TRX type is chosen by:
environment conditions required data throughput (GPRS/EDGE)
TX power of EVOLIUM™ Evolution step 2 TRX :Frequency band TX output power, GMSK TX output power, 8-PSK (EDGE)GSM 900 HP 60 W = 47.8 dBm 25 W = 44.0 dBmGSM 1800 HP 60 W = 47.8 dBm 25 W = 44.0 dBm
Section 1 · Module 1 · Page 319
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 319
2.10.2 Repeater Systems
2.10.2.13 3x6 TRXs High Power Configuration
Configuration made with EVOLIUM™ A9100 Base StationObs:
All TRX are HPThe configuration is using cell split feature
Cabinet1(High power 3x3TRX)
Sector3: 1x6 TRXSector2: 1x6 TRXSector1: 1x6 TRX
Cabinet2(High power 3x3TRX)
No-com-bining
ANc
HPTRX1 HPTRX 2
Combi-ning
MPTRX 3
No-com-bining
ANc
HPTRX1 HPTRX 2
Combi-ning
MPTRX 3
No-com-bining
ANc
HPTRX1 HPTRX 2
Combi-ning
MPTRX 3
No-com-bining
ANc
HPTRX1 HPTRX 2
Combi-ning
MPTRX 3
No-com-bining
ANc
HPTRX1 HPTRX 2
Combi-ning
MPTRX 3
No-com-bining
ANc
HPTRX1 HPTRX 2
Combi-ning
MPTRX 3
Section 1 · Module 1 · Page 320
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 320
2.10.2 Repeater Systems
2.10.2.14 Mixed TRX Configuration
BTS EVOLIUM™ supports a mix of:EVOLIUM™ TRX (TRE) - supports GSM/GPRS and EDGEEVOLIUM™ Evolution step 2 TRX (TRA) with Medium PowerEVOLIUM™ Evolution step 2 TRX (TRA) with High Power
TRE
TRE
TRA
MP
TRA
HP
Hardware configuration
Logical cell
TRX1 (BCCH)
TRX2 (1 SDCCH)
TRX3
TRX4
Packet VoiceAllocation
Section 1 · Module 1 · Page 321
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 321
3 Traffic & Frequency Planning
Section 1 · Module 1 · Page 322
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 322
3 Fraffic & Frequency Planning
3.1 Traffic Caspacity
Section 1 · Module 1 · Page 323
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 323
3.1 Traffic Capacity
3.1.1 Telephone System
subscriber
1
2
3
4
line to PSTN
sub 1
sub 2
sub 3
sub 4
timeobservation period, e.g.main busy hour (MBH)
blocked callattempts
Parameters:
λ: arrival rate [1/h]μ: release rate [1/h]1/μ: mean holding time [sec]
"offered" traffic = # of calls arriving in MBH × mean holding time ρ = λ × 1/μ [Erlang]
automaticswitch
Section 1 · Module 1 · Page 324
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 324
3.1 Traffic Capacity
3.1.2 Offered Traffic and Traffic Capacity
Handled Traffic, Traffic Capacity: TBlocking Probability, Grade of Service (GoS): pblock = R / ρSystem load: τ = T / n, i.e. T < n
Loss System(n slots)
HandledTraffic (T)
OfferedTraffic (ρ)
Rejected Traffic (R)
T = ρ - R
Section 1 · Module 1 · Page 325
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 325
3.1 Traffic Capacity
3.1.3 Definition of Erlang
ERLANG : Unit used to quantify traffic
T = (resource usage duration)/(total observation duration) [ERLANG]
Section 1 · Module 1 · Page 326
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 326
3.1 Traffic Capacity
3.1.4 Call Mix and Erlang Calculation
CALL MIX EXAMPLE350 call/hour3 LU/callTCH duration : 85 secSDCCH duration : 4,5 sec
ERLANG COMPUTATIONTCH = (350 * 85)/3600 = 8,26 ERLANGSDCCH = [ (350 + 350*3) * 4,5 ] / 3600 = 1.75 ERLANG
Section 1 · Module 1 · Page 327
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 327
3.1 Traffic Capacity
3.1.5 ERLANG B LAW
ERLANG B LAW
Relationship between
Offered trafficNumber of resourcesBlocking rate
Section 1 · Module 1 · Page 328
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 328
3.1 Traffic Capacity
3.1.5 ERLANG B LAW (2)
call request arrival rate (and leaving) is not stablenumber of resources = average number of requests mean duration is sometime not sufficent => probability of blocking
=> Erlang B law Pblock : blocking probabilityN : number of resourcesE : offered traffic [Erlang]
Calculated with Excel - Makro or Table
Section 1 · Module 1 · Page 329
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 329
3.1 Traffic Capacity
3.1.6 Erlang´s Formula
How to calculate the traffic capacity T?Basics: Markov Chain (queue statistics)
Calculation of the blocking probability using Erlang´s formula (Erlang B statistics):
Varation of ρ until pblock reached: ρ → Tp
n iblock
n i
i
n= ∑
=
ρ ρ! !0
p0 p1
2μμ
λ
pi
λ
pnnμ
p2
3μ
no callestablishe
d
i channels occupied
all channels occupied
Section 1 · Module 1 · Page 330
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 330
3.1 Traffic Capacity
3.1.7 Blocking Probability (Erlang B)
Nr. of Blocking Probability Erlang Bchannels 0.1% 0.2% 0.5% 1% 2% 3% 4% 5% 10% 15% 20% 50%
1 0.001 0.002 0.005 0.010 0.020 0.031 0.042 0.053 0.111 0.176 0.250 1.0002 0.046 0.065 0.105 0.153 0.223 0.282 0.333 0.381 0.595 0.796 1.000 2.7323 0.194 0.249 0.349 0.455 0.602 0.715 0.812 0.899 1.271 1.602 1.930 4.5914 0.439 0.535 0.701 0.869 1.092 1.259 1.399 1.525 2.045 2.501 2.945 6.5015 0.762 0.900 1.132 1.361 1.657 1.875 2.057 2.218 2.881 3.454 4.010 8.4376 1.146 1.325 1.622 1.909 2.276 2.543 2.765 2.960 3.758 4.445 5.109 10.3897 1.579 1.798 2.157 2.501 2.935 3.250 3.509 3.738 4.666 5.461 6.230 12.3518 2.051 2.311 2.730 3.128 3.627 3.987 4.283 4.543 5.597 6.498 7.369 14.3209 2.557 2.855 3.333 3.783 4.345 4.748 5.080 5.370 6.546 7.551 8.522 16.294
10 3.092 3.427 3.961 4.461 5.084 5.529 5.895 6.216 7.511 8.616 9.685 18.27311 3.651 4.022 4.610 5.160 5.842 6.328 6.727 7.076 8.487 9.691 10.857 20.25412 4.231 4.637 5.279 5.876 6.615 7.141 7.573 7.950 9.474 10.776 12.036 22.23813 4.831 5.270 5.964 6.607 7.402 7.967 8.430 8.835 10.470 11.867 13.222 24.22414 5.446 5.919 6.663 7.352 8.200 8.803 9.298 9.730 11.473 12.965 14.413 26.21215 6.077 6.582 7.376 8.108 9.010 9.650 10.174 10.633 12.484 14.068 15.608 28.20116 6.721 7.258 8.099 8.875 9.828 10.505 11.059 11.544 13.500 15.176 16.807 30.19117 7.378 7.946 8.834 9.652 10.656 11.368 11.952 12.461 14.522 16.289 18.010 32.18218 8.046 8.644 9.578 10.437 11.491 12.238 12.850 13.385 15.548 17.405 19.216 34.17319 8.724 9.351 10.331 11.230 12.333 13.115 13.755 14.315 16.579 18.525 20.424 36.16620 9.411 10.068 11.092 12.031 13.182 13.997 14.665 15.249 17.613 19.647 21.635 38.15921 10.108 10.793 11.860 12.838 14.036 14.885 15.581 16.189 18.651 20.773 22.848 40.15322 10.812 11.525 12.635 13.651 14.896 15.778 16.500 17.132 19.692 21.901 24.064 42.14723 11.524 12.265 13.416 14.470 15.761 16.675 17.425 18.080 20.737 23.031 25.281 44.14224 12.243 13.011 14.204 15.295 16.631 17.577 18.353 19.031 21.784 24.164 26.499 46.13725 12.969 13.763 14.997 16.125 17.505 18.483 19.284 19.985 22.833 25.298 27.720 48.13230 16.684 17.606 19.034 20.337 21.932 23.062 23.990 24.802 28.113 30.995 33.840 58.11335 20.517 21.559 23.169 24.638 26.435 27.711 28.758 29.677 33.434 36.723 39.985 68.09940 24.444 25.599 27.382 29.007 30.997 32.412 33.575 34.596 38.787 42.475 46.147 78.08845 28.447 29.708 31.656 33.432 35.607 37.155 38.430 39.550 44.165 48.245 52.322 88.07950 32.512 33.876 35.982 37.901 40.255 41.933 43.316 44.533 49.562 54.029 58.508 98.072
Section 1 · Module 1 · Page 331
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 331
3.1 Traffic Capacity
3.1.8 BTS Traffic Capacity (Full Rate)
Number of Speech Traffic (Erlang B) Signalling Traffic (Erlang B)TRX SDCCH TCH 1% 2% 5% 0.1% 0.2% 0.5%1 4 7 2.501 2.935 3.738 0.439 0.535 0.7012 8 14 7.352 8.2 9.73 2.051 2.311 2.733 8 22 13.651 14.896 17.132 2.051 2.311 2.734 16 29 19.487 21.039 23.833 6.721 7.258 8.0995 16 37 26.379 28.254 31.64 6.721 7.258 8.0996 24 44 32.543 34.682 38.557 12.243 13.011 14.2047 24 52 39.7 42.124 46.533 12.243 13.011 14.2048 32 59 46.039 48.7 53.559 18.205 19.176 20.678
Section 1 · Module 1 · Page 332
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 332
3 Fraffic & Frequency Planning
3.2 Network Evolution
Section 1 · Module 1 · Page 333
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 333
3.2 Network Evolution
3.2.1 Network Evolution - Capacity Approach (1)
The roll out of a network is dedicated to provide coverage
Network design changes rapidly
Planning method must be flexible and fast (group method)
Manual frequency planning possible
Section 1 · Module 1 · Page 334
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 334
3.2 Network Evolution
3.2.2 Network Evolution - Capacity Approach (2)
With the growing amount of subscribers, the need for more installed capacity is rising
Possible Solutions:
Installing more TRXs on the existing BTS
Implementing additional sites
Discussion!
Also new services like GPRS are demanding more capacity
Section 1 · Module 1 · Page 335
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 335
3.2 Network Evolution
3.2.3 Network Evolution - Capacity Approach (3)
Installing more TRXs - AdvantagesNo site search/acquisition processNo additional sites to rent (saves cost)Trunking efficiency Higher capacity per cell
Installing more TRXs - DisadvantagesMore antennas on roof top (Air combining)Additional losses if WBC has to be used
Less (indoor) coverageMore frequencies per site neededTighter reuse necessary decreasing quality
Trunking efficiency
1TRX 2.7 Erl. +2.7 Erl
2TRX 8.2 Erl +5.3 Erl (+1 Signalling TS)
3TRX 14.9 Erl +6.7 Erl
4TRX 21.0 Erl +6.1 Erl (+1 Signalling TS)
5TRX 28.3 Erl +7.3 Erl
6TRX 34.7 Erl +6.4 Erl (+1 Signalling TS)
7TRX 42.1 Erl +7.4 Erl
….
Section 1 · Module 1 · Page 336
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 336
3.2 Network Evolution
3.2.4 Network Evolution - Capacity Approach (4)
Implementing additional sites - AdvantagesReuse can remain the same (smaller cell sizes)Needs less frequency spectrum
higher spectrum efficiency
Implementing additional sites - DisadvantagesAdditional site cost (rent)Re-design of old cells necessary (often not done)
Section 1 · Module 1 · Page 337
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 337
3 Fraffic & Frequency Planning
3.3 Cell Structures
Section 1 · Module 1 · Page 338
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 338
3.3 Cell Structures
3.3.1 Cell Structures and Quality
Frequency re-use in cellular radio networksallow efficient usage of the frequency spectrumbut causes interference
Interdependence ofCell sizeCluster sizeRe-use distanceInterference levelNetwork Quality
interfererregion
Section 1 · Module 1 · Page 339
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 339
3.3 Cell Structures
3.3.2 Cell Re-use Cluster (Omni Sites) (1)
1
2 3
47
6 5 1
2 3
47
6 5RD
Section 1 · Module 1 · Page 340
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 340
3.3 Cell Structures
3.3.2 Cell Re-use Cluster (Omni Sites)(2)
5 64
1 2 3
7 8 9
10 11 12
D
Section 1 · Module 1 · Page 341
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 341
3.3 Cell Structures
3.3.4 Cell Re-use Cluster (Sector Site) (1)
Section 1 · Module 1 · Page 342
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 342
3.3 Cell Structures
3.3.5 4x3 Cell Re-use Cluster (Sector Site) (2)
Section 1 · Module 1 · Page 343
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 343
3.3 Cell Structures
3.3.6 Irregular (Real) Cell Shapes
12 3
4
56
5
7Network Border
CoverageHole Island
Section 1 · Module 1 · Page 344
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 344
3 Fraffic & Frequency Planning
3.4 Frequency Reuse
Section 1 · Module 1 · Page 345
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 345
3.4 Frequency Reuse
3.4.1 GSM Frequency Spectrum
GSM 900DL: 935-960 MHz UL: 890-915 MHz200 kHz channel spacing 124 channelsARFCN 1 - 124
E-GSMDL: 925-935 MHz UL: 880-890 MHz200 kHz channel spacing Additional 50 channelsARFCN 0, 975 - 1023200 kHz channel spacing 124 channels
GSM 850DL: 869-894 MHz UL: 824-849 MHzARFCN: 128 - 251
GSM 1800DL: 1805-1880 MHz UL: 1710-1785 MHz200 kHz channel spacing 374 channelsARFCN 512 - 885
Section 1 · Module 1 · Page 346
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 346
3.4 Frequency Reuse
3.4.2 Impact of limited Frequency Spectrum
Bandwidth is an expensive resource
Best usage necessary
Efficient planning necessary to contain good QoS when the traffic in
the network is increasingsmaller reuse Multiple reuse pattern (MRP) usageimplementation of concentric cells / microcells/dual bandimplementation of Frequency Hopping
BasebandSynthezised
Section 1 · Module 1 · Page 347
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 347
3.4 Frequency Reuse
3.4.3 What is frequency reuse?
As the GSM spectrum is limited, frequencies have to be reused toprovide enough capacity
The more often a frequency is reused within a certain amount of cells, the smaller the frequency reuse
Aim:Minimizing the frequency reuse for providing more capacity
REUSE CLUSTER:Area including cells which do not reuse the same frequency (or frequency group)
Section 1 · Module 1 · Page 348
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 348
3.4 Frequency Reuse
3.4.4 RCS and ARCS (1)
Reuse Cluster Size - RCSIf all cells within the reuse cluster have the same amount of TRXs, the reuse per TRX layer can be calculated:
cellTRXBRCS
/#=
cellTRXBARCS
/#=
Average Reuse Cluster Size - ARCSIf the cells are different equiped, the average number of TRXs has to be used for calculating the average reuse cluster size:
Section 1 · Module 1 · Page 349
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 349
3.4 Frequency Reuse
3.4.5 RCS and ARCS (2)
The ARCS is giving the average reuse of the network when using the whole bandwidth and all TRXs per cellE.g: if we want to have the reuse of all non hopping TCH TRXs, we have to use the dedicated bandwidth and the average number of non hopping TCH TRXs per cell to get the ARCS of this layer type.Each cell has only one BCCH. Therefore the BCCH reuse is an RCS and not an ARCS!
Section 1 · Module 1 · Page 350
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 350
3.4 Frequency Reuse
3.4.6 Reuse Cluster Size (1)
Sectorized sites4 sites per reuse cluster3 cells per site
REUSE Cluster Size:4X3 =12
1 2
3
4 5
6
7 8
9
10 11
12
1 2
3
4 5
6
7 8
9
10 11
12
Section 1 · Module 1 · Page 351
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 351
3.4 Frequency Reuse
3.4.7 Reuse Cluster Size (2)
Sectorized sites3 sites per reuse cluster3 cells per site
REUSE Cluster Size3X3 = 9
1 2
3
4 5
6
7 8
9
1 2
3
4 5
6
7 8
9
Section 1 · Module 1 · Page 352
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 352
3.4 Frequency Reuse
3.4.8 Reuse Distance
RCSRfD ⋅⋅⋅= 3
⎪⎩
⎪⎨⎧
= cells sectorized-three32
cells ionalomnidirect1f
re-use distancecell A
cell B
interfererregion
In theory reuse distance and reuse shouldn’t be dependent.
In reality, when the cells are not well designed: bigger cell overlapp =>higher frequency reuse, smaller reuse distance
Section 1 · Module 1 · Page 353
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 353
3.4 Frequency Reuse
3.4.9 Frequency Reuse Distance
site A site B
distance DR
D = distance between cell sites with the same frequenciesR = service radius of a cellB = number of frequencies in total bandwidthRCS = reuse cluster size, i.e. one cell uses B/RCS frequencies
In hexagonal cell geometry: D/R = f · 3 RCS
omni cells: f=1; sector cells: f=2/3
Examples (omni):RCS = 7: D/R = 4.6RCS = 9: D/R = 5.2RCS =12: D/R = 6.0
Received Power
Frec
σC/I
Frec, A Frec, B
0
Section 1 · Module 1 · Page 354
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 354
3.4 Frequency Reuse
3.4.10 Frequency Reuse: Example
No sectorization7 cells per cluster
BCCH RCS = 7TCH Reuse: Depending on BW and Number of installed TRXs per cellExample:
B= 264TRXs per cell
interfererregion
63
1726=
−−=
GuardBCCHRCSTCH
RCSTCH
RCSBCCH
BCCH reuse is always RCS, because we don’t need to use an average (always one BCCH per cell).
Omni cells
To calculate the TCH reuse in the example, the BCCH RCS is subtracted from the bandwidth B and the average number of TCH TRX per cell is4 minus 1 BCCH = 3
Section 1 · Module 1 · Page 355
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 355
3 Fraffic & Frequency Planning
3.5 Cell Planning
Section 1 · Module 1 · Page 356
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 356
3.5 Cell Planning
3.5.1 Cell Planning - Frequency Planning (1)
Can frequency planning be seen independently from cell planning?
Discussion
Section 1 · Module 1 · Page 357
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 357
3.5 Cell Planning
3.5.2 Cell Planning - Frequency Planning (2)
Bad cell planningIsland coverage disturbing the reuse patternBig overlap areas bigger reuse necessary
Good cell planningSharp cell borders good containment of frequencySmall overlap areas tighter reuse possible
Section 1 · Module 1 · Page 358
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 358
3.5 Cell Planning
3.5.3 Influencing Factors on Frequency Reuse Distance
Topography
Hilly terrain Usage of natural obstacles to define sharp cell borders tighter frequency reuse possible
Flat terrain Achieveable reuse much more dependent on the accurate cell design
Morphology
Water low attenuation high reuse distance
City high attenuation low reuse distance
Section 1 · Module 1 · Page 359
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 359
3.5 Cell Planning
3.5.4 Conclusion
In cellular mobile networks, the frequency reuse pattern has a direct influence on the interference and hence the network qualityRegular hexagonal patterns allow the deduction of engineering formulasIn real networks, cell sizes and shapes are irregular due to
Variation in traffic densityTopographyLand usage
Engineering formulas allow the assessment of the network quality and worst-case considerations, but the real situation must be proved!
Section 1 · Module 1 · Page 360
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 360
3.5 Cell Planning
3.5.5 Examples for different frequency reuses
Big city in the south of Africa:BCCH reuse 26
Irregular cell designMixed morphologyLots of waterFlat terrain plus some high sites
Big city in eastern EuropeBCCH reuse 12
Regular cell designFlat areaOnly urban environment
Section 1 · Module 1 · Page 361
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 361
3 Fraffic & Frequency Planning
3.6 Interference Probability
Section 1 · Module 1 · Page 362
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 362
3.6 Interference Probability
3.6.1 Interference Theory (1)
C/I restrictions9dB for co-channel interference-9 dB for adjacent channel interference
distance DR
Received PowerP rec
σC/ I
Prec, A Prec, B
0
C/I is the difference between the two received power lines
when shifting the two transmitters towards each other, the area where the C/I is > 9dB shrinks
At a certain distance of the two transmitters, the C/I can never fulfil the GSM criteria -> minimum site distance.
It has to be kept in mind, that of course other cells will be inbetween two cells transmitting at the same frequency!
Section 1 · Module 1 · Page 363
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 363
3.6 Interference Probability
3.6.2 Interference Theory (2)
Probability density function [%]
0,0%
1,0%
2,0%
3,0%
4,0%
5,0%
C/I [dB] →C/ImedC/Ithr
Margin
Interferer probability [%]
0%
20%
40%
60%
80%
100%
-20 -15 -10 -5 0 5 10 15 20
C/I - C/Ithr[dB]
Interference probabilityC/Imed is the calculated carrier tointerference ratio at a certain location (pixel)
ARCS Pint[%]6.5..9.0 107.0..9.5 7.58.5..11.0 5.012.0..16.0 2.5
3.6 Interference Probability
The marked area left of C/Ithr is the area of interference. Although the received level is above the threshold, there is a certain probability to get interference because of the standard deviation of the received signal.
Section 1 · Module 1 · Page 364
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 364
3.6 Interference Probability
3.6.3 CPDF - Cumulative Probability Density Function
Pint = P ( C/I < C/I thr)
00,10,20,30,40,50,60,70,80,91
P int
Distance from serving cellDR
CPDF - Cumulative Probability Density Function
Section 1 · Module 1 · Page 365
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 365
3.6 Interference Probability
3.6.4 Interference Probability dependent on Average Reuse
ARCS =# of frequencies in used bandwidth
average # of carriers per cellPint [%]
ARCS0
3
6
9
12
5 10 15 20 25
Examples:Pint[%] ARCS10 6.5...97.5 7...9.55 8.5...112.5
12...16
Section 1 · Module 1 · Page 366
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 366
3 Fraffic & Frequency Planning
3.7 Carrier Types
Section 1 · Module 1 · Page 367
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 367
3.7 Carrier Types
3.7.1 Carrier Types - BCCH carrier
BCCH frequency is on air all the time
If there is no traffic/signaling on TS 1 to 7dummy bursts are transmitted
PC (Power Control) and DTX (Discontinuous Transmission) are not allowed
Important for measurements of the mobile
The BCCH frequency must be transmitted with full power all the time!
Otherwise the measurements of the neighborcell levels would be useless.
Section 1 · Module 1 · Page 368
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 368
3.7 Carrier Types
3.7.2 Carrier Types - TCH carrier
PC allowed and recommended for UL and DLReduction of transmit power according to the actual path lossCareful parameter tuning for DL necessary
DTX allowed and recommended for UL and DLDiscontinuous TransmissionIf there is no speech, nothing is transmittedGeneration of comfort noise at receiving mobile
TCH not in use no signal is transmitted
Special case: Concentric cellsDifferent re-uses for inner and outer zone are possible
PC and DTX are reducing the overall interference in the network.
As a TCH is not transmitting anything when not in use, the interference level is strongly related to the traffic on the interfereing cells.
Section 1 · Module 1 · Page 369
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 369
3 Fraffic & Frequency Planning
3.8 Multiple Reuse Pattern MRP
Section 1 · Module 1 · Page 370
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 370
3.8 Multiple reuse pattern
3.8.1 Meaning of multiple reuse pattern (1)
For different types of carriers, different interference potential is expected
As the BCCH carrier has the highest interferer potential because of being on air all the time and the BCCH channel itself is accepting only low interference, the REUSE on the BCCH layer is higher then on other layers
TCH layers can be planned with a smaller REUSE
Inner zones of concentric cells are able to deal with the smallest reuse in non hopping networks
Section 1 · Module 1 · Page 371
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 371
3.8 Multiple reuse pattern
3.8.2 Meaning of multiple reuse pattern (2)
REUSE clusters forINNER ZONE layer
TCH layer
BCCH layer
When applying different reuses in the different cell layers, of course separated bands are necessary!
Section 1 · Module 1 · Page 372
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 372
3.8 Multiple reuse pattern
3.8.3 GSM restrictions
Intra site minimum channel spacing 2Intra cell minimum channel spacing 2 (ETSI recommends 3, but with Alcatel EVOLIUM capabilities this value can be set to 2)
constrains:Uplink power control enabledIntra cell interference handover enabled
f A1,
f A2,
f A3,
...
fB1 ,fB2 ,fB3 ,...f C1
,f C2,f C3
,...
Frequencies fAx,fBx,fCx,… must have at least 2 channels spacing
Frequencies fx1,fx2,fx3,… must have at least 3 channels spacing
The Intra cell minimum channel spacing of 3 is given by the combiner in the BTS, to avaoid IM problems
Important remark: the whole training is compliant to the co-cell constraint of 3 channels ; this is more restrictive than the BTS capability of filtering the channels on frequency n*200 kHz
Acc to A.Krause: for Evolium BTS standard equipped with WBC the co-cell constraint can be only 2 channels.
(A channel spacing of 2 was tested @Vodacom in 1999 but the result was not better than with channel spacingof 3.)
Section 1 · Module 1 · Page 373
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 373
3 Fraffic & Frequency Planning
3.9 Intermodulation
Section 1 · Module 1 · Page 374
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 374
3.9 Intermodulation
3.9.1 Intermodulation problems (1)
IM Products GSM900In a GSM 900 system intermodulation products of 3rd and 5th order can cause interference
2 * f1,t – f2,t = f2,r / 2 * f2,t – f1,t = f1,r
3 * f1,t – 2 * f2,t = f2,r / 3 * f2,t – 2 * f1,t = f1,r
Frequency planning must avoid fulfilling these equations
Both frequencies must be on the same duplexer
To avoid intra band IM inside GSM900 the following frequency separations shall be avoided:
75/112/113 channels
IM5 IM3
Info from techn. dept: If a WBC has to be used because of the number of TRXs, the output power is not high enough to cause problems. -> No intermodulation problems .
Section 1 · Module 1 · Page 375
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 375
3.9 Intermodulation
3.9.2 Intermodulation problems (2)
IM Products GSM1800In a GSM 1800 system, only intermodulation products of 3rd order can cause measurable interference2 * f1,t – f2,t = f2,r / 2 * f2,t – f1,t = f1,r
Frequency separations to be avoided
237/238 channels
IM Products Dual Band (GSM900/GSM1800)
f1800,t – f900,t = f900,r
Decoupling between the GSM 1800 TX path and the GSM 900 RX path is less than 30 dB (e.g. same antenna used!)
Section 1 · Module 1 · Page 376
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 376
3.9 Intermodulation
3.9.3 Intermodulation problems (3) - Summary
carrier/antenna restrictionG3 900 1 noG3 900 2 ore more 112/113 (IM3) and 75 (IM5)G3 1800 1 noG3 1800 2 or more 237/238 (IM3) no IM5 quality degradation measurable
carrier/antennaG2 900 w/o dupl 1 no
2 or more noG2 900 with dupl 1 no
2 or more 112/113 (IM3) and 75 (IM5)G2 1800 w/o dupl 1 no
2 or more noG2 1800 with dupl 1 no
22
G3 900 G2/G3 1800 f(1800,t) - f(900,t) = f(900,r)
G2 900 w/o dupl G2/G3 1800 no
G2 900 with dupl G2/G3 1800 f(1800,t) - f(900,t) = f(900,r)
Colocated BTSs
dud2(high Power) -> nodupd -> 237/238
OUTSIDE Problem: Dual Band
INSIDE Problem: IM3 / IM5
Problem only for non hopping and BCCH carriers
Problem can be solved by hopping over more than 10 frequencies
Caution: SFH doesn’t bring additional benefits when hopping over more than 4 frequencies
Section 1 · Module 1 · Page 377
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 377
3.9 Intermodulation
3.9.4 Treating “neighbor” cells
Cells, which are not declared as neighbor cells but are located in the neighborhood may use adjacent frequencies if it is not avoidable, but no co channel frequencies
Cells which are declared as neighbors, thus have HO relationships, must not use co or adjacent frequencies
If an adjacent frequency is used, the HO will be risky and at least audible by the user
Section 1 · Module 1 · Page 378
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 378
3.9 Intermodulation
3.9.5 Where can I find neighbor cells?
At the OMC-R for each cell a list of neighbor cells is defined
Maximum number of neighbors: 32
The list of neighbors and their frequencies is transmitted to the mobile to be able to perform measurements on these frequencies
In case of a HO cause, the HO will be performed towards the bestneighbor
Section 1 · Module 1 · Page 379
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 379
3 Fraffic & Frequency Planning
3.10 Manual frequency planning
Section 1 · Module 1 · Page 380
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 380
3.10 Manual Frequency Planning
3.10.1 Frequency planning (1)
No fixed method
Free frequency assignment possible, but very time consuming for larger networks
For easy and fast frequency planning: use group assignment
Example:18 channels, 2TRX per cell ARCS 9
Section 1 · Module 1 · Page 381
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 381
3.10 Manual Frequency Planning
3.10.2 Frequency planning (2)
GSM restrictions are automatically fulfilled, if on one site only groups A* or only B* are used
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
A1B1A2B2A3B3A4B4A5
Section 1 · Module 1 · Page 382
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 382
3.10 Manual Frequency Planning
3.10.3 Exercise: Manual frequency planning (1)
A1
A2 A3
A2
A4 A5
B4
B1
B2 B3
B1
B2
A1
A2 A3A2A4
A5
B4
B1B2
A1
A2 A3
Section 1 · Module 1 · Page 383
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 383
3.10 Manual Frequency Planning
3.10.4 Exercise: Manual frequency planning (2)
A1
A2A3
A2
A4 A5
B4
B1
B2 B3
B1
B2
A1
A2A3A2A4
A5
B2
B4B1
A3
A2A1
Section 1 · Module 1 · Page 384
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 384
3.10 Manual Frequency Planning
3.10.5 Discussion: Subdivide frequency band?
Any subdivision of the frequency band is reducing the spectrum efficiency!
Separations should be avoided if possible!
As the BCCH has to be very clean, it is nevertheless recommended to use a separated band and select a bigger reuse
The focus in the discussion is not the fx band splitting by fx management authorities.
Section 1 · Module 1 · Page 385
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 385
3.10 Manual Frequency Planning
3.10.6 Hint for creating a future proofed frequency plan
If a frequency plan is implemented, using all available frequencies in the most efficient way, it is very difficult to implement new sites in the future!
New sites would make a complete re-planning of the surrounding area or the whole frequency plan necessary
To avoid replanning every time when introducing new sites, it is recommended to keep some Joker frequencies free
These Joker frequencies can be used for new sites (especially BCCH TRXs) unless it is impossible to implement new sites without changing a big part of the frequency plan
New frequency plan necessary!
Section 1 · Module 1 · Page 386
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 386
3.10 Manual Frequency Planning
3.10.7 Implementing a frequency plan
If only a few frequencies have to be changed, the changes can bedone at the OMC-R
Disadvantage: Every cell has to be modified separatelyDowntime of the cell approx. 5 minutes
If lots of changes have to be done, it is of advantage to use external tools
Since B6.2 the complete frequency plan can be uploaded from the OMCthe uploaded file can be modified by the tool (A9155 PRC Generator)the the new plan is downloaded into the network and activated at once
Section 1 · Module 1 · Page 387
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 387
3 Fraffic & Frequency Planning
3.11 BSCI planning
Section 1 · Module 1 · Page 388
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 388
3.11 BSIC Planning
3.11.1 BSCI allocation
Together with the frequencies the Base Transceiver Station Identity Code (BSIC) has to be planned
The BSIC is to distinguish between cells using the same BCCH frequency
BSIC = NCC (3bits) + BCC (3bits)NCC Network (PLMN) Colour Code BCC - Base Transceiver Station (BTS) Colour Code
BSIC planning is supported by the A9155 (Alcatel Radio Network Planning Tool)
Section 1 · Module 1 · Page 389
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 389
3.11 BSIC Planning
3.11.2 BSIC planning rules
The same combination BCCH/BSIC must not be used on cell influencing on each other (having a mutual interference <>0)BSIC allocation rules:
Avoid using same BCCH/BSIC combination of:neighbor cellssecond order neighbor cells (the neighbors of neighbor cell (OMC limitation))
neighbor Cell
BCCH:24
BSIC:36
neighbor Cell
BCCH:24
BSIC: must NOT be 36
Serving Cell
BCCH:10
BSIC: any
A
B C
Section 1 · Module 1 · Page 390
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 390
3.11 BSIC Planning
3.11.3 Spurious RACH
Bad BSIC planning can cause SDCCH congestion cause by the spurious RACH problem, also known as “Ghost RACH”
This problem occurs, when a mobile sends an HO access burst to aTRX of cell A using the same frequency as a nearby cell B uses on the BCCH
Both cells using the same BSIC and Training Sequence Code TSQC, the HO access burst is understood by the cell B as a RACH for call setup
Therefore on cell B SDCCHs are allocated everytime a HO access burst is sent from the mobile to the cell A
If in cell B the BCCH and TRX 2 exchange their frequencies (BCCH gets the fx of TRX2 and TRX2 gets the fx of BCCH): no problem with spurious RACH
Cell BF1 F2
BSIC=1
Cell AF5F1
BSIC=1
Cell C
Section 1 · Module 1 · Page 391
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 391
3.11 BSIC Planning
3.11.4 Summary
For optimal usage of your frequency spectrum a good cell design is essentialUse larger reuse for BCCH frequenciesUse spectrum splitting only when necessary
Section 1 · Module 1 · Page 392
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 392
3 Fraffic & Frequency Planning
3.12 Capacity Enhancement Techniques
Section 1 · Module 1 · Page 393
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 393
3.12 Capacity Enhancement Techniques
3.12.1 Capacity enhancement by planning
Interference reduction of cellsCheck of antenna type, direction and down tilt
This is a check of cell size, border and orientationCheck of proper cabling
Is TX and RX path on the same sector antenna?Check of the frequency plan
Introduction of a better frequency plan
Section 1 · Module 1 · Page 394
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 394
3.12 Capacity Enhancement Techniques
3.12.2 Capacity enhancement by adding feature
Frequency hoppingBase band hoppingSynthesized frequency hopping
Concentric cellsHalf rate
Section 1 · Module 1 · Page 395
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 395
3.12 Capacity Enhancement Techniques
3.12.3 Capacity enhancement by adding TRX
Adding TRX to existing cellsMulti band cellsConcentric cells
Section 1 · Module 1 · Page 396
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 396
3.12 Capacity Enhancement Techniques
3.12.4 Capacity enhancement by adding cells
Adding of cells at existing site locationsAdding new cell = adding new BCCHDual band
Adding cells using another frequency bandCell splitting
Reduction of cell sizeChange of one omni cell into several cells/sector cells
Section 1 · Module 1 · Page 397
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 397
3.12 Capacity Enhancement Techniques
3.12.5 Capacity enhancement by adding sites
Dual band/multi band networkAdding of new sites in new frequency band
Multi layer networkAdding of new sites in another layer
E.g. adding micro cells for outdoor coverage
Indoor coverageAdding micro cells indoor coverageAdding macro cells indoor coverage
Section 1 · Module 1 · Page 398
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 398
Blank Page
This page is left blank intentionally
Section 1 · Module 1 · Page 399
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 399
4.1 GSM Air Interface
4 Radio Interface
Section 1 · Module 1 · Page 400
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 400
4.1 GSM Air Interface
4.1.1 Radio Resources
Radio Spectrum Allocation
Frequency(FDMA)
Time(TDMA)
Timeslot0<TN<7
TDMA Frames0<FN<FN_MAX
Carrier Frequencies (ARFCN)
Cell Allocation(CA)
Mobile Allocation(MA)
FDMA Frequency division multiple accessTDMA Time division multiple accessARFCN Absolute radio frequency channel numberTN Timeslot numberFN Frame number
Section 1 · Module 1 · Page 401
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 401
FDMA and TDMA with 8 time slots per carrierRF frequency band
(E)GSM: (880) 890 ... 915 MHz Uplink (MS → BS)(925) 935 ... 960 MHz Downlink (BS → MS)
GSM1800: 1710 ... 1785 MHz Uplink1805 ... 1880 MHz Downlink
200 kHz bandwidthNumber of carriers: 124 (GSM); 374 (DCS); 49 (E-GSM)
4.1 GSM Air Interface
4.1.2 GSM Transmission Principles (1)
GSM: Flower (n) = 890 + 0.2 · n MHz with 1 ≤ n ≤ 124E-GSM: Flower (n) = 890 + 0.2 · n MHz with 0 ≤ n ≤ 124
Flower (n) = 890 + 0.2 · (n -1024) MHz with 975 ≤ n ≤ 1023DCS : Flower (n) = 1710.2 + 0.2 · (n - 512) MHz with 512 ≤ n ≤ 885
(E)GSM: Fupper (n) = Flower (n) + 45 MHzDCS: Fupper (n) = Flower (n) + 95 MHz
Section 1 · Module 1 · Page 402
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 402
4.1 GSM Air Interface
4.1.3 GSM Transmission Principles (2)
Channel typesTraffic Channels (TCH)
Full rateHalf rate
Control Channels (CCH)Broadcast Control Channel (BCCH)Common Control Channel (CCCH)Dedicated Control Channel (DCCH)
TDMA frame cycles26 cycle for traffic channels51 cycle for control channels
Section 1 · Module 1 · Page 403
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 403
4.1 GSM Air Interface
4.1.4 Advantages of Signal Processing
Spectrum limitationsBad propagation
conditions
P
t
Good spectrum efficiency Good transmission quality
Operator
Section 1 · Module 1 · Page 404
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 404
4.1 GSM Air Interface
4.1.5 Signal Processing Chain
stealing bit and FACCH
speechcoding
errorprotection
interleaving encryption modulation
radiochannel
stealing bit and FACCH
speechinput
speechdecoding
errorcorrection
de-interleaving decryption demodulation
speechoutput
LossNoise
InterferenceFading
Section 1 · Module 1 · Page 405
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 405
4 Radio Interface
4.2 Channel Coding
Section 1 · Module 1 · Page 406
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 406
4.2 Channel Coding
4.2.1 Speech Coding
260 bits speech block
182 class 1 bits
20 ms of coded speech
78 class 2 bits
sensitive to bit errorsmust be protected
robust to bit errors
Coding algorithm: RPE-LTPPre-computationRPE = Regular Pulse Excitation
Model of human voice generationLTP = Long Term Prediction
Reduction of bit rate
Bit rate: 13 kBit/s
Coding at fixed network: PCM A-lawBit rate: 64 kBit/s
Section 1 · Module 1 · Page 407
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 407
4.2 Channel Coding
4.2.2 Error Protection
Messages (signalling data)
Fire Code
184 bits
184 40
4
Convolutional Coder = 1/2, K = 5
456 = 24 x 19
456 bits in 20 ms = 22.6kbit/s
Convolutional Coder = 1/2, K = 5
Tail bits
Parity check
Cycliccode
Speech (full rate)
Tail bits
Class 1a50 bits
Class 1b132 bits
Class 278 bits
= 456= 8 x 5737
878
50
3 132 4
260 bits
Section 1 · Module 1 · Page 408
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 408
4.2 Channel Coding
4.2.3 Interleaving and TDMA Frame Mapping
1 2 3 4 5 6 70 1 2 3 4 5 6 70
Mappingonto bursts
....
.
....
.
Addition of stealing flags
....
.
Interleaving
....
.
....
.
....
.
2 x 57 bits
Block n-1 (456 bits)
57 bits Block n (456 bits) Block n+1 (456 bits)
1 2 3 4 5 6 70
1 time slot
114 bits 114 bits 114 bits 114 bits 114 bits 114 bits 114 bits 114 bits
116 bits 116 bits 116 bits 116 bits 116 bits 116 bits 116 bits 116 bits
burst n-3 burst n-2 burst n-1 burst n burst n+1 burst n+2 burst n+3 burst n+4
Section 1 · Module 1 · Page 409
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 409
4.2 Channel Coding
4.2.4 Encryption
AlgorithmA3
Randomnumber
generator
AlgorithmA8
IMSIKi
Ki RAND (128 bit)
+
Authentication
yes/noAlgorithm
A3
AlgorithmA8
RAND
SRES (32 bit)
SIMCard
Ki
AlgorithmA5
AlgorithmA5
+
Kc (64 bit)
+
RAND
Kc
originaldata
originaldata
encrypted
data
encrypted
data
Network Mobile station
AuC
Section 1 · Module 1 · Page 410
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 410
4.2 Channel Coding
4.2.5 Burst Structure
0 1 2 3 4 5 6 7
TDMA frame = 4.615 ms
Data TrainingSequence Data
57 bits3 26 bits1 31 57 bits
tail bits tail bitsstealing flags
156.25 bit periods = 0.577 ms
GP GP
A burst contains one data "portion" of one timeslotTDMA frame: time between two bursts with same timeslot numberThe burst also consists of:
Guard period (GP): allows for transition and settling timesTail bits: allow for small shifts in time delay (synchronisation)Stealing flags: to indicate FACCH (control channel) dataTraining sequence: for equalization purposes
Normal Burst
0
Section 1 · Module 1 · Page 411
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 411
4.2 Channel Coding
4.2.4 Synchronisation
received at MS(downlink)
transmitted from MS(uplink)
transmitted from BTS(downlink)
received at BTS(uplink)
Transmitted bursts need a travelling time (TT) to the receiverFor network access, the MS sends a (non-synchronized) shortened RACH burstThe BSS measures the TT and generates a timing advance value TA which is transmitted to the MS
0 1 2 3
1 2
0 1 2
1 2
TT TT
non-synchronized
3 TSdelay
0 1 2 3 4 5 6 7 0 1
0 1 2 3 4 5 6 7 0 1
0 1 2 3 4 5 6 7 0 1
0 1 2 3 4 5 6 7 0 1
TT
TT
synchronized
RACH
MS delay line setting
1
4
2
3
Section 1 · Module 1 · Page 412
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 412
4.2 Channel Coding
4.2.5 Modulation
Gaussian minimum shift keyingBased on phase shift keyingReduction of required bandwidth
Maximum phase change during one bit durationBaseband filtering to achieve continuous phase changes
∫
cos
sin
+
x
x
≈90°
to RF modulatorDataϕ
Section 1 · Module 1 · Page 413
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 413
4.2 Channel Coding
4.2.6 Propagation Environment
Radio propagation is characterised by dispersive multi-path caused by reflection and scattering
Moving MS causes Doppler spectrum→ Definition of propagation models in the time
domain to allow channel simulationsTUxx (Typical Urban)RAxx (Rural Area)HTxx (Hilly Terrain)xx = speed in km/h
see also GSM 05.05, 11.20, 11.21
Section 1 · Module 1 · Page 414
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 414
4.2 Channel Coding
4.2.7 Equalizing
Purpose: equalize distortions in transmission spectrumAdaptive filtering required
Filter parameters determined out of the training sequenceFilter parameters change from burst to burst
Equalizer takes advantage from multipath propagation (path diversity)
0.001
0.01
0.1
0 1 2 3 4 5 6 7 8
Delay of second path [chips]B
ER
noneAlcatelMLSE
Equalizer
Section 1 · Module 1 · Page 415
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 415
4.2 Channel Coding
4.2.8 Definition of Bit Error Rates
FER = Frame Erasure RateRatio of corrupted frames, indicated by a wrong CRC (cyclic redundancy checksum) and BFI (bad frame indicator)
RBER = Residual Bit Error Rateconsidering corrupted frames not recognized as bad frames
BER = total bit error rateConsideration of class 1 or 2 bits → e.g. RBER1b, RBER2
see also GSM 05.05, 11.20, 11.21
Section 1 · Module 1 · Page 416
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 416
BER Quality
>0.01 no communication<0.005 “bad”<0.0025 “marginal”<0.0003 “good”<0.0001 “excellent”
Thresholds:
C/I: 9 dBEc/No: 8 dBBTS (GSM900): -104 dBmHH (GSM900): -102 dBmBTS (GSM1800): -104 dBmHH (GSM1800): -100 dBm
4.2 Channel Coding
4.2.9 Speech Quality
HH - handheld
RXQUAL_0 BER <0,2%
RXQUAL_1 0,2%<BER<0,4%
RXQUAL_2 0,4%<BER<0,8%
RXQUAL_3 0,8%<BER<1,6%
RXQUAL_4 1,6%<BER<3,2%
RXQUAL_5 3,2%<BER<6,4%
RXQUAL_6 6,4%<BER<12,8%
RXQUAL_7 12,8%<BER
Section 1 · Module 1 · Page 417
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 417
4.2 Channel Coding
4.2.10 Dependence of BER on Noise and Interference
Variation of BER1 over C/IParameter: Ec/N0
How to find a quality figure?BER1 for marginal speech quality: 0.25%required C/I ≈ 9 dB for TU50 environmentbut: signal must not be close to noise floor!
C/I [dB] →
TU50BER1
→
Section 1 · Module 1 · Page 418
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 418
4.2 Channel Coding
4.2.13 Frequency Hopping (1)
-70
-60
-50
-40
-30
-20
-10
0
0.1
2.8
5.4
8.0
10.6
13.2
15.9
18.5
21.1
23.7
26.3
29.0
31.6
34.2
36.8
39.4
42.1
44.7
47.3
49.9
Distance [m]
Rec
eive
d Po
wer
[dB
m]
Lognormal fadingRaleygh fading
Problem: specific fading pattern for each used frequencyFast MS cope with the situation (due to signal processing)Slow MS suffer from fading holesSolution: change the fading pattern by frequency hopping
Fading holes
Section 1 · Module 1 · Page 419
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 419
4.2 Channel Coding
4.2.14 Frequency Hopping (2)
Variation of BER1 over Ec/N0TU environment, flat fading, v = 0 km/h (worst case)Parameter: number of hopping frequencies
Compensation with 4 hopping frequencies possible
Ec/N0 [dB] →
BER
→
Section 1 · Module 1 · Page 420
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 420
4.2 Channel Coding
4.2.15 The OSI Reference Model
Definition in GSM recommendations: layers 1 to 3Notion of "Physical" channels and "Logical" channels
7
6
5
4
3
2
1
Application layer
Presentation layer
Session layer
Transport layer
Network layer
Data link layer
Physical layer
End system End systemTransportation system
04.0408.54
04.05/0608.56
04.07/0808.58/4.0
8
Section 1 · Module 1 · Page 421
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 421
4.2 Channel Coding
4.2.16 GSM Burst Types (1)
Normal BurstFor regular transmission
Frequency Correction BurstContains 142 zeros (0) → pure sine waveAllows synchronisation of the mobile's local oscillator
Synchronisation BurstConsists of an enlarged unique training sequence code (TSC)Contains the actual FN → time synchronisation
Access BurstShortened burst (unique TSC and enlarged guard period)Timeslot overlapping avoided at BTS when MS accesses network
Dummy Burst"Filler" for unused BCCH timeslots → BCCH permanently on airSimilar to normal burst (defined mixed bits for data, no stealing flag)
Section 1 · Module 1 · Page 422
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 422
4.2 Channel Coding
4.2.17 GSM Burst Types (2)
TB3
57 data bits 126 bit training
sequence1 57 data bits
TB3
Normal burstGP
8.25
TB3
142 fixed bits (pure sine wave) TB3
Frequency correction burstGP
8.25
TB3
39 data bits 64 bit trainingsequence
39 data bits TB3
Synchronisation burstGP
8.25
TB8
36 data bits41 bit synchronisationsequence
Access burstenlarged GP
68.25 bitTB3
Section 1 · Module 1 · Page 423
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 423
4.2 Channel Coding
4.2.18 Logical Channels
Trafficchannel
Controlchannel
Speech Data
TCH/FS
TCH/HS
TCH/F9.6
TCH/F4.8
TCH/F2.4
TCH/H4.8
TCH/H2.4
CCCHBroadcastchannel
Associatedchannel
Dedicatedchannel
FCCH
SCH
BCCH
RACH
PCH
AGCH
FACCH
SACCH
SDCCH
CBCH
Section 1 · Module 1 · Page 424
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 424
4.2 Channel Coding
4.2.19 Possible Channel Combinations
1
2
3
4
5
6
7
TCH/F+FACCH/F+SACCH/TF
TCH/H(0.1)+FACCH/H(0.1)+SACCH/TH(0.1)
TCH/H(0.0)+FACCH/H(0.1)+SACCH/TH(0.1)+TCH/H(1.1)
FCCH+SCH+BCCH+CCCH
FCCH+SCH+BCCH+CCCH+SDCCH/4(0..3)+SACCH/C4(0..3)
BCCH+CCCH
SDCCH/8(0..7)+SACCH/C8(0..7)
CCCH = PCH+RACH+AGCHCombination 4 and 5 is only possible on TS0 of the first (BCCH) carrierCombination 6 is possible on TS2, TS4, or TS6 of the BCCH carrier
Section 1 · Module 1 · Page 425
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 425
4.2 Channel Coding
4.2.20 Channel Mapping (1)
time
..............
.......
0 0 0 01 1 112 2 223 3 334 4 445 556 6 67 7 7
one TDMA frame = 4.616 ms
Information packages are always related to the same timeslot number!Bursts are transmitted and received every TDMA frame duration (4.616 ms)Presentation of consecutive
TDMA frames on the vertical axis
Section 1 · Module 1 · Page 426
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 426
4.2 Channel Coding
4.2.21 Channel Mapping (2)
SCH
FCCH RACH
SCH
FCCH
SCH
FCCH
SCH
FCCH
SCH
FCCH
RACH
RACH
RACH
RACH
RACH
RACH
RACH
RACH
RACH
RACH
RACH
RACH
RACH
RACH
RACH
RACH
RACH
RACH
RACH
RACH
RACH
RACH
RACH
RACH
RACH
RACH
RACH
RACH
RACH
RACH
RACH
RACH
RACH
RACH
RACH
RACH
RACH
RACH
RACH
RACH
RACH
RACH
RACH
RACH
RACH
RACH
RACH
RACH
RACH
RACH
SCH
FCCH
SCH
FCCH
SCH
FCCH
SCH
FCCH
SCH
FCCH
SCH
FCCH
SCH
FCCH
SCH
FCCH
SCH
FCCH
SCH
FCCH
RACH
RACH
RACH
RACH
RACH
RACH
RACH
RACH
RACH
RACH
RACH
RACH
RACH
RACH
RACH
RACH
RACH
RACH
RACH
RACH
RACH
RACH
RACH
RACH
RACH
RACH
RACH
RACH
RACH
RACH
RACH
RACH
RACH
RACH
RACH
RACH
RACH
RACH
RACH
RACH
RACH
RACH
RACH
RACH
RACH
RACH
RACH
RACH
RACH
RACH
RACH
RACH
RACH
RACH
BCCH
CCCH
CCCH
CCCH
CCCH
CCCH
CCCH
CCCH
CCCH
CCCH
BCCH BCCH
CCCH
CCCH
CCCH
CCCH
CCCH
CCCH
SDCCH0
SDCCH1
SDCCH2
SDCCH3
SDCCH0
SDCCH1
SDCCH2
SDCCH3
SDCCH0
SDCCH1
SDCCH0
SDCCH1
SDCCH2
SDCCH3
SDCCH2
SDCCH3
SACCH0
SACCH1
SACCH2
SACCH3
TCH
TCH
TCH
TCH
TCH
TCH
TCH
TCH
TCH
TCH
TCH
TCH
SACCH
TCH
TCH
TCH
TCH
TCH
TCH
TCH
TCH
TCH
TCH
TCH
TCH
TCH
TCH
TCH
TCH
TCH
TCH
TCH
TCH
TCH
TCH
TCH
TCH
SACCH
TCH
TCH
TCH
TCH
TCH
TCH
TCH
TCH
TCH
TCH
TCH
TCH
SDCCH0
SDCCH1
SDCCH2
SDCCH3
SDCCH4
SDCCH5
SDCCH6
SDCCH7
SACCH0
SACCH1
SACCH2
SACCH3
SACCH0
SACCH1
SACCH2
SACCH3
SDCCH0
SDCCH1
SDCCH2
SDCCH3
SDCCH4
SDCCH5
SDCCH6
SDCCH7
SACCH4
SACCH5
SACCH6
SACCH7
SDCCH0
SDCCH1
SDCCH2
SDCCH3
SDCCH4
SDCCH5
SDCCH6
SDCCH7
SACCH0
SDCCH0
SDCCH1
SDCCH2
SDCCH3
SDCCH4
SDCCH5
SDCCH6
SDCCH7
SACCH1
SACCH2
SACCH3
SACCH4
SACCH5
SACCH6
SACCH7
0
10
20
30
40
50
0
10
20
30
40
50
0
12
25
0
12
25
not combined BCCHdownlink uplink downlink uplink downlink uplink
combined BCCH TCH SDCCHup/downlink
Control channelsFollows a 51-cycleDuration: 235.4 msecConsists mostly of four consecutive blocksSynchronisation with FCCH and SCH
Traffic channelsFollows a 26-cycleDuration: 120 msec
Section 1 · Module 1 · Page 427
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 427
4.2 Channel Coding
4.2.22 TDMA Frame Structure for TCHs
TB3
57 data bits 126 bit trainingsequence
1 57 data bits TB3
GP8.25
0 1 2 3 4 5 6 7
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25
Time slot
Frame
Multiframe
Superframe
Hyperframe
51 multiframes of 120 ms duration
2048 superframes of 6.12 s duration
0.577 ms
4.615 ms
120 ms
6.12 s
3 h 28 m 53 s
Section 1 · Module 1 · Page 428
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 428
Abbreviations and Acronyms
AMR Advanced Multi Rate (TC)AMSS Aeronautical Mobile Satellite ServicesAN Antenna Network (BTS)ARCS Average Reuse Cluster SizeARFCN Absolute Radio Frequency ChannelAS Access Switch (BSC)AS Alarm Surveillance (O&M)ASMA A-ter Submultiplexer AASMB A-ter Submultiplexer BAuC Authentication CenterBC BroadcastBCU Broadcast UnitBCLA BSC Clock ABCR Broadcast RegisterBCU Broadcast UnitBCCH Broadcast Common Control Channel
(GSM TS)BCF Base station Control Function (BTS)BG Border Gate (GPRS)
BIE Base Station Interface EquipmentBIEC Base Station Interface Equipment (BSC)BIUA Base Station Interface Unit ABPA Back Panel AssemblyBSC Base Station ControllerBSIC Base Transceiver Station Identity CodeBSS Base Station (sub)SystemBSSGP Base Station System GPRS Protocol
(GPRS)BTS Base Transceiver StationCAE Customer Application EngineeringCAL Current Alarm List (O&M)CBC Cell Broadcast CenterCBCH Cell Broadcast Channel (GSM TS)CBE Cell Broadcast EntityCCCH Common Control Channel (GSM TS)CCU Channel Coding Unit
Section 1 · Module 1 · Page 429
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 429
Abbreviations and Acronyms [cont.]
CDMA Code Division Multiple AccessCE Control Element (BSC)CEK Control Element KernelC/I Carrier to Interferer ratioCLK ClockCLSI Custom Large Scale Integrated circuitCMA Configuration Management Application (O&M)CMDA Common Memory Disk ACMFA Common Memory Flash ACPR Common Processor (Type: CPRA, CPRC)CRC Cyclic Redundancy CheckCS Circuit Switching (Telecom)CS Coding Scheme (GPRS):
CS-1, CS-2, CS-3, CS-4CU Carrier Unit (BTS)DCE Data Circuit Terminating EquipmentDCN Data Communication NetworkDL DownLink
DLS Data Load SegmentDMA Direct Memory AccessDRFU Dual Rate Frame UnitDRX Discontinuous Reception (GSM TS)DSE Digital Switching ElementDSN Digital Switching NetworkDTX Discontinuous Transmission (GSM TS)DTC Digital Trunk Controller
(Type: DTCA, DTCC)DTE Data Terminal EquipmentEDGE Enhanced Data rates for GSM EvolutionEDA Extended Dynamic AllocationEI Extension interfaceEML Element Management LevelEPROM Erasable Programmable Read Only
MemoryETSI European Telecom Standard InstituteFPE Functional and Protective EarthFR Full Rate (GSM TS)
Section 1 · Module 1 · Page 430
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 430
Abbreviations and Acronyms [cont.]
FR Frame Relay (Telecom)FRDN Frame Relay Data Network (Telecom)FU Frame Unit (BTS)FW FirmwareGCR Group Call RegisterGGSN Gateway GPRS Support Node (GPRS)GMLC Gateway Mobile Location CenterGMM GPRS Mobility Management (GPRS)GMSC Gateway Mobile Switching CenterGPRS General Packet Radio ServiceGPU GPRS Packet UnitGS-1 Group Switch of stage 1 (BSC)GS-2 Group Switch of stage 2 (BSC)GSL GPRS Signalling LinkGSM Global System for Mobile CommunicationsGSM TS GSM Technical SpecificationHAL Historical Alarm List (O&M)HDSL High rate Digital Subscriber LineHDLC High Level Datalink Control
HLR Home Location RegisterHMI Human Machine InterfaceHO HandOverHR Half RateHW HardwareIDR Internal Directed RetryILCS ISDN Link ControllerIMT Installation and Maintenance Terminal
(MFS)IND Indoor (BTS)IP Internet ProtocolISDN Integrated Services Data NetworkIT Intelligent TerminalLA Location Area (GSM TS)LAC Location Area Code (GSM TS)LAN Local Area NetworkLED Light Emitting DiodeLEO Low Earth Orbit (Satellite)LCS Location Services
Section 1 · Module 1 · Page 431
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 431
Abbreviations and Acronyms [cont.]
PCH Paging CHannel (GSM TS)PCM Pulse Coded ModulationPCU Packet Control Unit (GPRS)PDCH Packet Data CHannelPDN Packet Data Network (Telecom)PDU Protocol Data Unit (generic terminology)PLL Phase Locked LoopPLMN Public Land Mobile NetworkPMA Prompt Maintenance Alarm (O&M)PMC Permanent Measurement Campaign
(O&M)PPCH Packet Paging CHannel (GPRS)PRACH Packet Random Access CHannel (GPRS)Prec Received PowerPRC Provisioning Radio Configuration (O&M)PSDN Packet Switching Data Network
(Telecom)
PSTN Public Switching Telephone Network(Telecom)
PTP-CNLS Point To Point CoNnectionLeSs datatransfer (GPRS)
QoS Quality of ServiceRA Radio AccessRACH Random Access CHannel (GSM TS)RAM Random Access MemoryRCP Radio Control PointRLC Radio Link Control (GPRS)RLP Radio Link Protocol (GSM TS)RML Radio Management LevelRNO Radio Network OptimisationRNP Radio Network PlanningRSL Radio Signalling Link
Section 1 · Module 1 · Page 432
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 432
Abbreviations and Acronyms [cont.]
RTS Radio Time SlotRxLev Received LevelRxQual Received QualitySACCH Slow Associated Control Channel
(GSM TS)SAU Subrack assembly unit (BSC)SC Supervised Configuration (O&M)SCC Serial Communication ControllerSCP Service Control PointSCCP Signalling Connection Control PartSCSI Small Computer Systems InterfaceSDCCH Standalone Dedicated Control Channel
(GSM TS)SDU Service Data Unit (generic terminology)SGSN Serving GPRS Support Node (GPRS)SIEA SCSI Interface Extension A
SM SubmultiplexerSMLC Serving Mobile Location CenterSMP Service Management PointSMS Short Message ServiceSMS-CB Short Message Service - Cell BroadcastSM-GMSC Short Message Gateway Mobile Switching
CenterSRAM Static RAMSRS SubRate SwitchSS7 Signalling System ITU-T N°7 (ex CCITT)SSD Solid State DiskSSP Service Switching PointSW SoftwareSWEL Switch ElementTBF Temporary Block Flow (GPRS)TAF Terminal Adaptor Function
Section 1 · Module 1 · Page 433
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 433
Abbreviations and Acronyms [cont.]
TC TranscoderTC Terminating CallTCC Trunk Controller ChipTCH Traffic CHannel (GSM TS)TCIL TransCoder Internal LinkTCSM TransCoder / SubMultiplexer equipmentTCU TRX Control Unit (Type: TCUA, TCUC)TDMA Time Division Multiple AccessTFO Tandem Free Operation (TC)TFTS Terrestrial Flight Telecom SystemsTLD Top Level DesignTMN Telecommunication Management
NetworkTRAC Trunk Access CircuitTRAU Transcoder and Rate Adapter UnitTRCU Transcoder UnitTRE Transceiver EquipmentTRS Technical Requirement SpecificationTRU Top Rack Unit
TRX TransceiverTS Time SlotTS Technical Specification (GSM TS)TSS Time Space Switch TSCA Transmission Sub-System Controller A
(BSC) TSU Terminal Sub Unit (BSC)TU Terminal Unit (BSC)UL UpLinkUMTS Universal Mobile Transmission SystemUSSD Unstructured Supplementary Services DataVBS Voice Broadcast ServiceVGCS Voice Group Code ServiceVLR Visitor Location RegisterVPLMN Visited PLMNVSWR Voltage Standing Wave Ratio (BTS)WAN Wide Area NetworkWAP Wireless Application ProtocolWBC Wide Band Combiner
Section 1 · Module 1 · Page 434
All Rights Reserved © Alcatel-Lucent 2010TMO54014 Issue 01
All Rights Reserved © Alcatel-Lucent 2010
RNE · RNE (Radio Network Engineering) B11 FundamentalsBasics · Basics1 · 1 · 434
End of ModuleBasics