rf12 programming guide - sparkfun electronics · pdf filerf12b programming guide . 1 ... rf12b...

RF12B Program V1.1

RF12B programming guide

1． Brief description

RF12B is a low cost FSK transceiver IC witch integrated all RF functions in a

single chip. It only need a MCU, a crystal, a decouple capacitor and antenna to

build a hi reliable FSK transceiver system. The operation frequency can cover 400

to 1000MHz.

RF12B supports a command interface to setup frequency, deviation, output power

and also data rate. No need any hardware adjustment when using in frequency-hopping

applications

RF12B can be used in applications such as remote control toys, wireless alarm,

wireless sensor, wireless keyboard/mouse, home-automation and wireless data

collection.

2． Commands 1． Timing diagram

2． Configuration Setting Command

bit 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 POR 1 0 0 0 0 0 0 0 el ef b1 b0 x3 x2 x1 x0 8008h

e l: Enable TX register

e f: Enable RX FIFO buffer

Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: [email protected] http://www.hoperf.com

RF12B Program V1.1

b1..b0: select band

B1 b0 band[MHz]

0 0 Reserved

0 1 433

1 0 868

1 1 915

x3..x0: select crystal load capacitor

X3 x2 x1 x0 load capacitor [pF]

0 0 0 0 8.5

0 0 0 1 9.0

0 0 1 0 9.5

0 0 1 1 10.0

…… ……

1 1 1 0 15.5

1 1 1 1 16.0

3． Power Management Command bit 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 POR 1 0 0 0 0 0 1 0 er ebb et es ex eb ew dc 8208h

er： Enable receiver ebb：Enable base band block et： Enable transmitter es： Enable synthesizer ex： Enable crystal oscillator eb： Enable low battery detector ew： Enable wake-up timer

dc： Disable clock output of CLK pin

4． Frequency Setting Command bit 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 POR 1 0 1 0 f11 f10 f9 f8 f7 f6 f5 f4 f3 f2 f1 f0 A680h

f11..f0: Set operation frequency: 433band: Fc=430+F*0.0025 MHz 868band: Fc=860+F*0.0050 MHz 915band: Fc=900+F*0.0075 MHz

Fc is carrier frequency and F is the frequency parameter. 36≤F≤3903


RF12B Program V1.1

5． Data Rate Command

bit 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 POR 1 1 0 0 0 1 1 0 cs r6 r5 r4 r3 r2 r1 r0 C623h

r6..r0: Set data rate:

BR=10000000/29/（R+1）/（1+cs*7）

6． Receiver Control Command bit 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 POR

1 0 0 1 0 P16 d1 d0 i2 i1 i0 g1 g0 r2 r1 r0 9080h

P16: select function of pin16

P16 0 Interrupt input 1 VDI output

i2..i0:select baseband bandwidth


i2 i1 i0 Baseband Bandwidth [kHz]

0 0 0 reserved

0 0 1 400

0 1 0 340

0 1 1 270

1 0 0 200

1 0 1 134

1 1 0 67

1 1 1 reserved

d1..d0: select VDI response time

d1 d0 Response

0 0 Fast

0 1 Medium

1 0 Slow

1 1 Always on

g1..g0: select LNA gain

g1 g0 LNA gain (dBm)

0 0 0

0 1 -6

1 0 -14

1 1 -20

RF12B Program V1.1


r2..r0: select DRSSI threshold

r2 r1 r0 RSSIsetth [dBm]

0 0 0 -103

0 0 1 -97

0 1 0 -91

0 1 1 -85

1 0 0 -79

1 0 1 -73

1 1 0 Reserved

1 0 1 Reserved

The actual DRSSI threshold is related to LNA setup:

RSSIth = RSSIsetth + GLNA.

7． Data Filter Command

bit 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 POR

1 1 0 0 0 0 1 0 al ml 1 s 1 f2 f1 f0 C22Ch

al: Enable clock recovery auto-lock ml: Enable clock recovery fast mode s: select data filter type

s Filter type 0 Digital filter

1 Analog RC filter

f1..f0: Set DQD threshold 8． FIFO and Reset Mode Command

bit 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 POR 1 1 0 0 1 0 1 0 f3 f2 f1 f0 sp al ff dr CA80h

f3..f0: Set FIFO interrupt level sp: Select the length of the synchron pattern:

sp Byte1 Byte0 (POR) Synchron Pattern (Byte1+Byte0) 0 2Dh D4h 2DD4h1 Not used D4h D4h

al: select FIFO fill start condition

al condition 0 Sync-word 1 Always

ff: Enable FIFO fill dr： Disable hi sensitivity reset mode

RF12B Program V1.1


9． Synchron pattern Command

bit 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 POR

1 1 0 0 1 1 1 0 b7 b6 b5 b4 b3 b2 b1 b0 CED4h

This command is used to reprogram the synchronic pattern; 10． Receiver FIFO Read Command

bit 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 POR 1 0 1 1 0 0 0 0 0 0 0 0 0 0 0 0 B000h

This command is used to read FIFO data when FFIT interrupt generated. FIFO data output starts at 8th SCK period. 11． AFC Command

bit 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 POR

1 1 0 0 0 1 0 0 a1 a0 rl1 rl0 st fi oe en C4F7h

a1..a0: select AFC auto-mode：

a1 a0

0 0 Controlled by MCU

0 1 Run once at power on

1 0 Keep offset when VDI hi

1 1 Keeps independently from VDI

rl1..rl0: select range limit

r1 r0 range（fres）

0 0 No restriction

0 1 +15/-16

1 0 +7/-8

1 1 +3-4

fres

315，433band: 2.5kHz 868band: 5kHz 915band: 7.5kHz

st: st goes hi will store offset into output register fi: Enable AFC hi accuracy mode oe: Enable AFC output register en: Enable AFC funcition

RF12B Program V1.1

12． TX Configuration Control Command

bit 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 POR

1 0 0 1 1 0 0 mp m3 m2 m1 m0 0 p2 p1 p0 9800h

m: select modulation polarity m2..m0: select frequency deviation:

m3 m2 m1 m0 frequency deviation [kHz]

0 0 0 0 15

0 0 0 1 30

0 0 1 0 45

0 0 1 1 60

0 1 0 0 75

0 1 0 1 90

0 1 1 0 105

0 1 1 1 120

1 0 0 0 135

1 0 0 1 150

1 0 1 0 165

1 0 1 1 180

1 1 0 0 195

1 1 0 1 210

1 1 1 0 225

1 1 1 1 240

p2..p0: select output power

p2 p1 p0 Output power[dBm]

0 0 0 0

0 0 1 -3

0 1 0 -6

0 1 1 -9

1 0 0 -12

1 0 1 -15

1 1 0 -18

1 0 1 -21


RF12B Program V1.1


13． PLL Setting Command

bit 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 POR

1 1 0 0 1 1 0 0 0 ob1 ob0 1 ddy ddit 1 bw0 CC77h

Note1： For A0 version, the default value is CC67, it is necessary to use CC77 instead of CC67 in the

application program.,

NOTE2: For A1 version, you can use the default value CC77.

ob1-ob0: Microcontroller output clock buffer rise and fall time control.

ob1 ob0 Selected uC CLK frequency

0 0 5 or 10 MHz (recommended)

0 1 3.3 MHz

1 X 2.5 MHz or less

ddy: phase detector delay enable.

ddi: disables the dithering in the PLL loop.

bw1-bw0: select PLL bandwidth bw0 Max bit rate [kbps] Phase noise at 1MHz offset [dBc/Hz]

0 86.2 -107

1 256 -102

14． Transmitter Register Write Command

bit 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 POR 1 0 1 1 1 0 0 0 t7 t6 t5 t4 t3 t2 t1 t0 B8AAh

This command is use to write a data byte to RF12 and then RF12 transmit it

15． Wake-Up Timer Command bit 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 POR 1 1 1 r4 r3 r2 r1 r0 m7 m6 m5 m4 m3 m2 m1 m0 E196h

The wake-up period is determined by:

Twake-up = M * 2R [ms]

16． Low Duty-Cycle Command

bit 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 POR

1 1 0 0 1 0 0 0 d6 d5 d4 d3 d2 d1 d0 en C8OEh

d6..d0: Set duty cycle D.C.= (D * 2 +1) / M *100%

en：Enable low duty cycle mode

RF12B Program V1.1


17． Low Battery Detector and Microcontroller Clock Divider Command

bit 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 POR

1 1 0 0 0 0 0 0 d2 d1 d0 0 v3 v2 v1 v0 C000h

d2..d0: select frequency of CLK pin

d2 d1 d0 Clock frequency[MHz]

0 0 0 1

0 0 1 1.25

0 1 0 1.66

0 1 1 2

1 0 0 2.5

1 0 1 3.33

1 1 0 5

1 1 1 10

CLK signal is derive form crystal oscillator and it can be applied to MCU clock in to save a second crystal. If not used, please set bit “dc” to disable CLK output To integrate the load capacitor internal can not only save cost, but also adjust reference frequency by software

v3..v0: Set threshold voltage of Low battery detector： Vlb=2.2+V*0.1 [V]

18． Status Read Command

bit 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 POR 0 x x x x x x x x x x x x x x x -

This command starts with a 0 and be used to read internal status register

RF12B Program V1.1

3． Demo flow diagram Transmitter:

Note: Initialize RF12B and open transmitter, RF12B will transmit a byte and pull nIRQ low when transmit over, then MCU can write next byte to transmit

Init RF12B

DEMO

Open TX

Send data

Close TX

Send data

Wait nIRQ low

Write a byte

Package send over?

return

N

Y


RF12B Program V1.1

Receiver:

Init RF12B

DEMO

Receive data

Indicate receive

Open RX

Check N

pass?

Y

Wait nIRQ low

Read FIFO data

Data recive over?

Y

N

return

Receive data

Note: After RF12B initialization, Open FIFO receive mode and wait nIRQ low, only then MCU can read received and stored in FIFO data. For next package receive, please reset FIFO.


RF12B Program V1.1

4． Example 1（for AVR microcontroller）

RF12 transmitter demo:

/*

; copyright (c) 2006

;Title RF12 TX simple example based on AVR C

;Company: Hope microelectronic Co.,Ltd.

;Author: Tank

;Current version: v1.0

;Date: 2006-11-13

;processor ATMEGA48

;Clock: 10MHz Crystal

;Contact: +86-0755-86106557

;E-MAIL: [email protected]

Connections

ATMEGA48 SIDE RF12 SIDE

SCK--------------->SCK

MISO--------------->SDO

MOSI--------------->SDI

SS--------------->nSEL

INT0<---------------nIRQ

PD6: LED GREEN

PD7: LED RED

*/


RF12B Program V1.1


#include <mega48.h>

#define DDR_IN 0

#define DDR_OUT 1

#define PORT_SEL PORTB

#define PIN_SEL PINB

#define DDR_SEL DDRB

#define PORT_SDI PORTB

#define PIN_SDI PINB

#define DDR_SDI DDRB

#define PORT_SCK PORTB

#define PIN_SCK PINB

#define DDR_SCK DDRB

#define PORT_SDO PORTB

#define PIN_SDO PINB

#define DDR_SDO DDRB

#define PORT_DATA PORTD

#define PIN_DATA PIND

#define DDR_DATA DDRD

#define PB7 7//--\

#define PB6 6// |

#define RFXX_SCK 5// |

#define RFXX_SDO 4// |RF_PORT

#define RFXX_SDI 3// |

#define RFXX_SEL 2// |

#define NC 1// |

#define PB0 0//--/

#define SEL_OUTPUT() DDR_SEL |= (1<<RFXX_SEL)

#define HI_SEL() PORT_SEL|= (1<<RFXX_SEL)

#define LOW_SEL() PORT_SEL&=~(1<<RFXX_SEL)

#define SDI_OUTPUT() DDR_SDI |= (1<<RFXX_SDI)

#define HI_SDI() PORT_SDI|= (1<<RFXX_SDI)

#define LOW_SDI() PORT_SDI&=~(1<<RFXX_SDI)

#define SDO_INPUT() DDR_SDO&= ~(1<<RFXX_SDO)

RF12B Program V1.1


#define SDO_HI() PIN_SDO&(1<<RFXX_SDO)

#define SCK_OUTPUT() DDR_SCK |= (1<<RFXX_SCK)

#define HI_SCK() PORT_SCK|= (1<<RFXX_SCK)

#define LOW_SCK() PORT_SCK&=~(1<<RFXX_SCK)

#define RF12_DATA 4//PD4

#define DATA_OUT DDR_DATA|=1<<RF12_DATA

#define HI_DATA PORT_DATA|=1<<RF12_DATA

#define LEDG_OUTPUT() DDRD|=~(1<<6)

#define LEDR_OUTPUT() DDRD|=~(1<<7)

#define LEDG_ON() PORTD&=~(1<<6)

#define LEDG_OFF() PORTD|=~(1<<6)

#define LEDR_ON() PORTD&=~(1<<7)

#define LEDR_OFF() PORTD|=~(1<<7)

void RFXX_PORT_INIT(void){

HI_SEL();

HI_SDI();

LOW_SCK();

SEL_OUTPUT();

SDI_OUTPUT();

SDO_INPUT();

SCK_OUTPUT();

}

unsigned int RFXX_WRT_CMD(unsigned int aCmd){

unsigned char i;

unsigned int temp;

LOW_SCK();

LOW_SEL();

for(i=0;i<16;i++){

temp<<=1;

if(SDO_HI()){

temp|=0x0001;

}

LOW_SCK();

if(aCmd&0x8000){

HI_SDI();

}else{

LOW_SDI();

}

RF12B Program V1.1


HI_SCK();

aCmd<<=1;

};

LOW_SCK();

HI_SEL();

return(temp);

}

void RF12_INIT(void){

RFXX_WRT_CMD(0x80D8);//EL,EF,433band,12.5pF

RFXX_WRT_CMD(0x8239);//!er,!ebb,ET,ES,EX,!eb,!ew,DC

RFXX_WRT_CMD(0xA640);//A140=430.8MHz

RFXX_WRT_CMD(0xC647);//4.8kbps

RFXX_WRT_CMD(0x94A0);//VDI,FAST,134kHz,0dBm,-103dBm

RFXX_WRT_CMD(0xC2AC);//AL,!ml,DIG,DQD4

RFXX_WRT_CMD(0xCA81);//FIFO8,SYNC,!ff,DR

RFXX_WRT_CMD(0xCED4);//SYNC=2DD4；

RFXX_WRT_CMD(0xC483);//@PWR,NO RSTRIC,!st,!fi,OE,EN

RFXX_WRT_CMD(0x9850);//!mp,9810=30kHz,MAX OUT

RFXX_WRT_CMD(0xCC77);//OB1，OB0,！lpx,！ddy，DDIT，BW0

RFXX_WRT_CMD(0xE000);//NOT USE

RFXX_WRT_CMD(0xC800);//NOT USE

RFXX_WRT_CMD(0xC040);//1.66MHz,2.2V

}

void RF12_SEND(unsigned char aByte){

while(PIND&(1<<2));//wait for previously TX over

RFXX_WRT_CMD(0xB800+aByte);

}

void Delay_ms(unsigned char amS){

unsigned char i;

unsigned int j;

for(i=0;i<amS;i++)for(j=0;j<914;j++);

}

void main(void)

{

unsigned int i,j;

unsigned char ChkSum;

#asm("cli");

DDRB=0x00;//PB INPUT;

DDRD=0x00;//PD INPUT;

//POWER ON indication: both LEDR and LEDG blink 3 times

LEDG_OFF();

RF12B Program V1.1


LEDR_OFF();

LEDG_OUTPUT();

LEDR_OUTPUT();

for(i=0;i<3;i++){

Delay_ms(200);

LEDG_ON();

LEDR_ON();

Delay_ms(200);

LEDG_OFF();

LEDR_OFF();

}

LEDG_OFF();

LEDR_OFF();

RFXX_PORT_INIT();

RF12_INIT();

DDRD|=(1<<RF12_DATA);

PORTD|=(1<<RF12_DATA);// SET nFFS pin HI when using TX register

DDRD&=~(1<<2); //PD2(INT0)

while(1){

LEDR_ON();

RFXX_WRT_CMD(0x0000);//read status register

RFXX_WRT_CMD(0x8239);//!er,!ebb,ET,ES,EX,!eb,!ew,DC

ChkSum=0;

RF12_SEND(0xAA);//PREAMBLE



RF12_SEND(0x2D);//SYNC HI BYTE

RF12_SEND(0xD4);//SYNC LOW BYTE

RF12_SEND(0x30);//DATA BYTE 0

ChkSum+=0x30;

RF12_SEND(0x31);//DATA BYTE 1

ChkSum+=0x31;

RF12_SEND(0x32);

ChkSum+=0x32;

RF12_SEND(0x33);

ChkSum+=0x33;

RF12_SEND(0x34);

RF12B Program V1.1


ChkSum+=0x34;

RF12_SEND(0x35);

ChkSum+=0x35;

RF12_SEND(0x36);

ChkSum+=0x36;

RF12_SEND(0x37);

ChkSum+=0x37;

RF12_SEND(0x38);

ChkSum+=0x38;

RF12_SEND(0x39);

ChkSum+=0x39;

RF12_SEND(0x3A);

ChkSum+=0x3A;

RF12_SEND(0x3B);

ChkSum+=0x3B;

RF12_SEND(0x3C);

ChkSum+=0x3C;

RF12_SEND(0x3D);

ChkSum+=0x3D;

RF12_SEND(0x3E);

ChkSum+=0x3E;

RF12_SEND(0x3F); //DATA BYTE 15

ChkSum+=0x3F;

RF12_SEND(ChkSum); //send chek sum

RF12_SEND(0xAA);//DUMMY BYTE



RFXX_WRT_CMD(0x8201);

LEDR_OFF();

LEDG_OFF();

for(i=0;i<10000;i++)for(j=0;j<123;j++);//sleep 1 second appr.

};

}

RF12 receiver demo

/*

; copyright (c) 2006

;Title RF12 RX simple example based on AVR C

;Company: Hope microelectronic Co.,Ltd.

;Author: Tank

RF12B Program V1.1


;Current version: v1.0

;Date: 2006-11-17

;processor ATMEGA48

;Clock: 10MHz Crystal

;Contact: +86-0755-86106557

;E-MAIL: [email protected]

Connections

ATMEGA48 SIDE RF12 SIDE

SCK--------------->SCK

MISO<---------------SDO

MOSI--------------->SDI

SS--------------->nSEL

PD4--------------->FSK/DATA

INT0<---------------nIRQ

PD6: LED GREEN

PD7: LED RED

*/

#include <mega48.h>

#define DDR_IN 0

#define DDR_OUT 1

#define PORT_SEL PORTB

#define PIN_SEL PINB

#define DDR_SEL DDRB

#define PORT_SDI PORTB

#define PIN_SDI PINB

#define DDR_SDI DDRB

#define PORT_SCK PORTB

#define PIN_SCK PINB

#define DDR_SCK DDRB

#define PORT_SDO PORTB

#define PIN_SDO PINB

#define DDR_SDO DDRB

RF12B Program V1.1


#define PORT_IRQ PORTD

#define PIN_IRQ PIND

#define DDR_IRQ DDRD

#define PORT_DATA PORTD

#define PIN_DATA PIND

#define DDR_DATA DDRD

#define PB7 7//--\

#define PB6 6// |

#define RFXX_SCK 5// |

#define RFXX_SDO 4// |RF_PORT

#define RFXX_SDI 3// |

#define RFXX_SEL 2// |

#define NC 1// |

#define PB0 0//--/

#define SEL_OUTPUT() DDR_SEL |= (1<<RFXX_SEL)

#define HI_SEL() PORT_SEL|= (1<<RFXX_SEL)

#define LOW_SEL() PORT_SEL&=~(1<<RFXX_SEL)

#define SDI_OUTPUT() DDR_SDI |= (1<<RFXX_SDI)

#define HI_SDI() PORT_SDI|= (1<<RFXX_SDI)

#define LOW_SDI() PORT_SDI&=~(1<<RFXX_SDI)

#define SDO_INPUT() DDR_SDO&= ~(1<<RFXX_SDO)

#define LOW_SDO() PORT_SDO&= (1<<RFXX_SDO)

#define SDO_HI() PIN_SDO&(1<<RFXX_SDO)

#define SCK_OUTPUT() DDR_SCK |= (1<<RFXX_SCK)

#define HI_SCK() PORT_SCK|= (1<<RFXX_SCK)

#define LOW_SCK() PORT_SCK&=~(1<<RFXX_SCK)

#define RF12_IRQ 2

#define IRQ_IN() DDR_IRQ &=~(1<<RF12_IRQ)

#define WAIT_IRQ_LOW() while(PIND&(1<<RF12_IRQ))

#define RF12_DATA 4//PD4

#define DATA_OUT() DDR_DATA|=1<<RF12_DATA

#define HI_DATA() PORT_DATA|=1<<RF12_DATA

#define LEDG_OUTPUT() DDRD|=~(1<<6)

#define LEDR_OUTPUT() DDRD|=~(1<<7)

RF12B Program V1.1


#define LEDG_ON() PORTD&=~(1<<6)

#define LEDG_OFF() PORTD|= (1<<6)

#define LEDR_ON() PORTD&=~(1<<7)

#define LEDR_OFF() PORTD|= (1<<7)

void RFXX_PORT_INIT(void){

HI_SEL();

HI_SDI();

LOW_SCK();

//SET nFFS pin HI when using FIFO

HI_DATA();

SEL_OUTPUT();

SDI_OUTPUT();

SDO_INPUT();

SCK_OUTPUT();

IRQ_IN();

DATA_OUT();

}

unsigned int RFXX_WRT_CMD(unsigned int aCmd){

unsigned char i;

unsigned int temp;

temp=0;

LOW_SCK();

LOW_SEL();

for(i=0;i<16;i++){

if(aCmd&0x8000){

HI_SDI();

}else{

LOW_SDI();

}

HI_SCK();

temp<<=1;

if(SDO_HI()){

temp|=0x0001;

}

LOW_SCK();

aCmd<<=1;

};

HI_SEL();

return(temp);

}

RF12B Program V1.1


void RF12_INIT(void){

RFXX_WRT_CMD(0x80D8);//EL,EF,433band,12.5pF

RFXX_WRT_CMD(0x82D9);//!er,!ebb,ET,ES,EX,!eb,!ew,DC

RFXX_WRT_CMD(0xA640);//A140=430.8MHz

RFXX_WRT_CMD(0xC647);//4.8kbps

RFXX_WRT_CMD(0x94A0);//VDI,FAST,134kHz,0dBm,-103dBm

RFXX_WRT_CMD(0xC2AC);//AL,!ml,DIG,DQD4

RFXX_WRT_CMD(0xCA81);//FIFO8,SYNC,!ff,DR

RFXX_WRT_CMD(0xCED4);//SYNC=2DD4；

RFXX_WRT_CMD(0xC483);//@PWR,NO RSTRIC,!st,!fi,OE,EN

RFXX_WRT_CMD(0x9850);//!mp,9810=30kHz,MAX OUT

RFXX_WRT_CMD(0xCC77);//OB1，OB0,！lpx,！ddy，DDIT，BW0

RFXX_WRT_CMD(0xE000);//NOT USE

RFXX_WRT_CMD(0xC800);//NOT USE

RFXX_WRT_CMD(0xC040);//1.66MHz,2.2V

}

unsigned char RF12_RECV(void){

unsigned int FIFO_data;

WAIT_IRQ_LOW();

RFXX_WRT_CMD(0x0000);

FIFO_data=RFXX_WRT_CMD(0xB000);

return(FIFO_data&0x00FF);

}

void Delay_ms(unsigned char amS){

unsigned char i;

unsigned int j;

for(i=0;i<amS;i++)for(j=0;j<914;j++);

}

void main(void)

{

unsigned char i;

unsigned char ChkSum;

//POWER ON indication: both LEDR and LEDG blink 3 times

LEDG_OFF();

LEDR_OFF();

LEDG_OUTPUT();

LEDR_OUTPUT();

for(i=0;i<3;i++){

Delay_ms(200);

LEDG_ON();

LEDR_ON();

RF12B Program V1.1


Delay_ms(200);

LEDG_OFF();

LEDR_OFF();

}

LEDG_OFF();

LEDR_OFF();

//Initialize command port

RFXX_PORT_INIT();

//Initialize RF12 chip

RF12_INIT();

//Init FIFO

RFXX_WRT_CMD(0xCA81);

while(1){

//Enable FIFO


ChkSum=0;

//Receive payload data

for(i=0;i<16;i++){

ChkSum+=RF12_RECV();

}

//Receive Check sum

i=RF12_RECV();

//Disable FIFO


//Package chkeck

if(ChkSum==i){

LEDG_ON();

Delay_ms(200);

LEDG_OFF();

}

}

}

RF12B Program V1.1

5． Example 2（for PIC microcontroller）

RF12 transmitter demo:

/**********************************************************

copyright (c) 2006

Title: RFM12B transmitter simple example based on PIC C

Current version: v1.0

Function: Package send Demo

Processor PIC16F73 DIP-28

Clock: 10MHz Crystal

Operate frequency: 434MHz

Data rate: 4.8kbps

Package size: 23byte

Author: Robben

Company: Hope microelectronic Co.,Ltd.

Contact: +86-0755-86106557

E-MAIL: [email protected]

Date: 2006-11-21

********************************************************/

#include "pic.h"

typedef unsigned char uchar;

typedef unsigned int uint;

#define SDI RB7

#define SDO RB6

#define SCK RB5


RF12B Program V1.1


#define nSEL RB4

#define SDI_OUT() TRISB7=0

#define SDO_IN() TRISB6=1

#define SCK_OUT() TRISB5=0

#define nSEL_OUT() TRISB4=0

void Init_RF12(void);

void Write0( void );


void WriteCMD( uint CMD );

void DelayUs( uint us );

void DelayMs(uint ms);

void WriteFSKbyte( uchar DATA );

__CONFIG(0x3FF2);

void Init_RF12(void)

{

nSEL_OUT();

SDI_OUT();

SDO_IN();

SCK_OUT();

nSEL=1;

SDI=1;

SCK=0;

WriteCMD(0x80D8);//enable register,433MHz,12.5pF

WriteCMD(0x8208);//Turn on crystal,!PA

WriteCMD(0xA640);//

WriteCMD(0xC647);//

WriteCMD(0XCC77);//

WriteCMD(0x94A0);//VDI,FAST,134kHz,0dBm,-103dBm

WriteCMD(0xC2AC);

WriteCMD(0xCA80);

WriteCMD(0xCA83);//FIFO8,SYNC,

WriteCMD(0xC49B);

WriteCMD(0x9850);//!mp,9810=30kHz,MAX OUT

WriteCMD(0xE000);//NOT USE

WriteCMD(0xC80E);//NOT USE

WriteCMD(0xC000);//1.0MHz,2.2V

}

void main()

{

RF12B Program V1.1


uint ChkSum=0;

Init_RF12();

while(1)

{

WriteCMD(0x8228); //OPEN PA

DelayUs( 4 );

WriteCMD(0x8238);

NOP();

NOP();

WriteFSKbyte( 0xAA );



WriteFSKbyte( 0x2D );

WriteFSKbyte( 0xD4 );

WriteFSKbyte( 0x30 );//DATA0

ChkSum+=0x30;

WriteFSKbyte( 0x31 );//DATA1

ChkSum+=0x31;

WriteFSKbyte( 0x32 );

ChkSum+=0x32;


ChkSum+=0x33;


ChkSum+=0x34;


ChkSum+=0x35;


ChkSum+=0x36;


ChkSum+=0x37;


ChkSum+=0x38;


ChkSum+=0x39;

WriteFSKbyte( 0x3A );

ChkSum+=0x3A;

WriteFSKbyte( 0x3B );

ChkSum+=0x3B;

WriteFSKbyte( 0x3C );

ChkSum+=0x3C;

WriteFSKbyte(0x3D);

ChkSum+=0x3D;

WriteFSKbyte( 0x3E );

RF12B Program V1.1


ChkSum+=0x3E;

WriteFSKbyte( 0x3F );//DATA15

ChkSum+=0x3F;

ChkSum&=0x0FF;

WriteFSKbyte( ChkSum );


WriteCMD( 0x8208 ); //CLOSE PA

DelayMs(1000);

}

}

void Write0( void )

{

SCK=0;

NOP();

SDI=0;

NOP();

NOP();

NOP();

NOP();

NOP();

NOP();

NOP();

NOP();

NOP();

NOP();

NOP();

NOP();

NOP();

NOP();

NOP();

SCK=1;

NOP();

}

void Write1( void )

{

SCK=0;

NOP();

SDI=1;

NOP();

NOP();

NOP();

RF12B Program V1.1


NOP();

NOP();

NOP();

NOP();

NOP();

NOP();

NOP();

NOP();

NOP();

NOP();

NOP();

NOP();

SCK=1;

NOP();

}

void WriteCMD( uint CMD )

{

uchar n=16;

SCK=0;

nSEL=0;

while(n--)

{

if(CMD&0x8000)

Write1();

else

Write0();

CMD=CMD<<1;

}

SCK=0;

nSEL=1;

}

void WriteFSKbyte( uchar DATA )

{

uchar RGIT=0;

uint temp=0xB800;

temp|=DATA;

Loop: SCK=0;

nSEL=0;

SDI=0;

SCK=1;

if(SDO) //Polling SDO

RF12B Program V1.1


{

RGIT=1;

}

else

{

RGIT=0;

}

SCK=0;

SDI=1;

nSEL=1;

if(RGIT==0)

{

goto Loop;

}

else

{

RGIT=0;

WriteCMD(temp);

}

}

void DelayUs( uint us )

{

uint i;

while( us-- )

{

i=2;

while( i-- )

{

NOP();

}

}

}

void DelayMs(uint ms)

{

uchar i;

while(ms--)

{

i=35;

while(i--)

{

DelayUs(1);

RF12B Program V1.1


}

}

}

RF12 receiver demo:

/**********************************************************

copyright (c) 2006

Title: RFM12B transmitter simple example based on PIC C

Current version: v1.0

Function: Package send Demo

Processor PIC16F73 DIP-28

Clock: 10MHz Crystal

Operate frequency: 434MHz

Data rate: 4.8kbps

Package size: 23byte

Author: Robben

Company: Hope microelectronic Co.,Ltd.

Contact: +86-0755-86106557

E-MAIL: [email protected]

Date: 2006-11-17

********************************************************/

#include "pic.h"

typedef unsigned char uchar;

typedef unsigned int uint;

#define SDI RB7

#define SDO RB6

#define SCK RB5

#define nSEL RB4

#define nIRQ RB3

#define LED RA0

#define LED_OUT() TRISA0=0

#define nIRQ_IN() TRISB3=1

#define SDI_OUT() TRISB7=0

#define SDO_IN() TRISB6=1

#define SCK_OUT() TRISB5=0

#define nSEL_OUT() TRISB4=0

void Init_RF12(void);



RF12B Program V1.1


void WriteCMD( uint CMD );

uchar RF12_RDFIFO(void);

void Delayus( uint us );

__CONFIG(0x3FF2);

bank1 uchar RF_RXBUF[19];

void Init_RF12(void)

{

LED_OUT();

nSEL_OUT();

SDI_OUT();

SDO_IN();

SCK_OUT();

nIRQ_IN();

nSEL=1;

SDI=1;

SCK=0;

SDO=0;

LED=0;

WriteCMD(0x80D8);//enable register,433MHz,12.5pF

WriteCMD(0x82D8);//enable receive,!PA

WriteCMD(0xA640);//

WriteCMD(0xC647);//

WriteCMD(0x94A0);//VDI,FAST,134kHz,0dBm,-103dBm

WriteCMD(0xC2AC);

WriteCMD(0XCC77);//

WriteCMD(0xCA80);

WriteCMD(0xCA83);//FIFO8,SYNC,

WriteCMD(0xC49B);

WriteCMD(0x9850);//!mp,9810=30kHz,MAX OUT

WriteCMD(0xE000);//NOT USE

WriteCMD(0xC800);//NOT USE

WriteCMD(0xC000);//1.0MHz,2.2V

}

void main()

{

uchar i=0,j=0;

uint CheckSum;

Init_RF12();

while(1)

RF12B Program V1.1


{

while(!nIRQ)

{

RF_RXBUF[i++]=RF12_RDFIFO();

if(i==17)

{

i=0;

WriteCMD(0xCA80);

WriteCMD(0xCA83); //reset FIFO and read to receive next Byte

CheckSum=0;

for(j=0;j<16;j++)

CheckSum+=RF_RXBUF[j]; //add 0x30-----0x3F

CheckSum&=0x0FF;

if(CheckSum==RF_RXBUF[16])

{

LED=1;

}

Delayus(1);

LED=0;

}

}

}

}

void Write0( void )

{

SCK=0;

NOP();

SDI=0;

NOP();

NOP();

NOP();

NOP();

NOP();

NOP();

NOP();

NOP();

NOP();

NOP();

NOP();

NOP();

NOP();

NOP();

NOP();

RF12B Program V1.1


SCK=1;

NOP();

}

void Write1( void )

{

SCK=0;

NOP();

SDI=1;

NOP();

NOP();

NOP();

NOP();

NOP();

NOP();

NOP();

NOP();

NOP();

NOP();

NOP();

NOP();

NOP();

NOP();

NOP();

SCK=1;

NOP();

}

void WriteCMD( uint CMD )

{

uchar n=16;

SCK=0;

nSEL=0;

while(n--)

{

if(CMD&0x8000)

Write1();

else

Write0();

CMD=CMD<<1;

}

SCK=0;

nSEL=1;

}

RF12B Program V1.1


uchar RF12_RDFIFO(void)

{

uchar i,Result;

SCK=0;

SDI=0;

nSEL=0;

for(i=0;i<16;i++)

{ //skip status bits

SCK=1;

NOP();

NOP();

SCK=0;

NOP();

NOP();

}

Result=0;

for(i=0;i<8;i++)

{ //read fifo data byte

Result=Result<<1;

if(SDO)

{

Result|=1;

}

SCK=1;

NOP();

NOP();

SCK=0;

NOP();

NOP();

}

nSEL=1;

return(Result);

}

void Delayus( uint us )

{

uint i;

while( us-- )

{

i=1000;

while( i-- )

{

RF12B Program V1.1


NOP();

}

}

}

HOPE MICROELECTRONICS CO.,LTD Add:4/F, Block B3, East Industrial Area, Huaqiaocheng, Shenzhen, Guangdong, China Tel: 86-755-86096602 Fax: 86-755-86096587 Email: [email protected] Website: http://www.hoperf.com http://www.hoperf.cn http://hoperf.en.alibaba.com

This document may contain preliminary information and is subject to change by Hope Microelectronics without notice. Hope Microelectronics assumes no responsibility or liability for any use of the information contained herein. Nothing in this document shall operate as an express or implied license or indemnity under the intellectual property rights of Hope Microelectronics or third parties. The products described in this document are not intended for use in implantation or other direct life support applications where malfunction may result in the direct physical harm or injury to persons. NO WARRANTIES OF ANY KIND, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MECHANTABILITY OR FITNESS FOR A ARTICULAR PURPOSE, ARE OFFERED IN THIS DOCUMENT. ©2006, HOPE MICROELECTRONICS CO.,LTD. All rights reserved.

mailto:[email protected]

http://www.hoperf.com/

rf12 programming guide - sparkfun electronics · pdf filerf12b programming guide . 1 ... rf12b...

Documents