products. construction equipment - toolsrenewed.comtoolsrenewed.com/new tools/cp/co-2011...

Construction EquipmentHigh-performance products. Designed for you!

Introduction

The Chicago Pneumatic Brand offers a complete line of Construction Equipment designed to efficiently handle a broad range of applications.

Each Chicago Pneumatic (CP) tool is easy to use, comfortable to hold, and operates at top performance over an unusually long life. CP Compressors are reliable and easy to maintain. The range features proven designs with powerful engines from well known manufacturers.

Chicago Pneumatic Construction Equipment distributors are tool and compressor experts who can precisely match the performance characteristics of CP tools to your specific job requirements.

For tools, parts and accessory information, and for service, contact a CP Construction Equipment distributor nearest you. Find them listed on the web at www.cp.com, or by calling a customer service representative toll-free at 800-760-4049.

Limited Warranty

Products of the Chicago Pneumatic Brand (CP) are warranted to be free from defects in material and workmanship for one year from the date of purchase.

This warranty applies only to products purchased new from CP or its authorized dealers. Of course, this warranty does not apply to products which have been abused, misused, modified or repaired by someone other than CP or its Authorized Service Representatives.

If a CP product proves defective in material or workmanship within one year after purchase, return it to any Chicago Pneumatic Authorized Service Center for CP tools, transportation prepaid, enclosing your name and address, adequate proof of date of purchase and a short description of the defect. CP will, at its discretion, repair or replace defective products free of charge. Repairs or replacements are warranted as described above for the remainder of the original warranty period. CP’s sole liability and your exclusive remedy under this warranty is limited to repair or replacement of the defective product. There are not other warranties expressed or implied and CP shall not be liable for incidental, consequential or special damages, or any other damages, costs, or expenses excepting only the cost or expense of repair or replacement as described above.

A History of Unequaled Quality

In 2009, Chicago Pneumatic Tool Company (CP) celebrated 108 years as a pioneer and market leader in the pneumatic tool industry. When the company incorporated more than a century ago, pneumatic tools were a revolutionary new technology. J.W. Duntley, an ambitious foreman in a Milwaukee foundry, recognized the potential in these tools and set out to pursue his American dream.

With keen intellect and little money, he partnered with young steel tycoon Charles Schwab to manufacture and market air tools under the Chicago Pneumatic name. At

that time, most manufacturers specialized in creating only one type of tool. Duntley realized that if Chicago Pneumatic could manufacture and sell a complete line of pneumatic tools, it could provide superior service. In a sense, he had the vision for one-stop shopping for the pneumatic tool industry long before it became the norm.

He did not, however, realize his company would have such an impact on the world. As the industry’s most experienced manufacturer, Chicago Pneumatic has developed tools that were used to build and main-tain some of the world’s most recognizable landmarks. CP impact wrenches and rivet busters were used to construct iconic and engineering marvels such as the Empire State Building and the Golden Gate Bridge. The company’s concrete vibrators were partially responsible for the construction of the Hoover Dam, one of America’s “seven modern civil engineering wonders”.

When the United States found itself embroiled in World War II, CP produced the tools necessary to fabricate, assemble and maintain the nation’s military equipment. And in addition to helping the nation’s defense, one Chicago Pneumatic tool became part of an icon that symbolizes American character and courage. In the painting “Rosie the Riveter”, by legendary illustrator Norman Rockwell, the well-recognized factory worker eats her lunch with a CP riveting hammer lying on her lap.

Chicago Pneumatic continued to expand its global business as the century progressed, and even began making its mark on space travel. During the late 1960s and early 70s, in the Apollo program, the United States sent men into space and explored the moon. What is arguably the most technologically advanced organization in the world depended on Chicago Pneumatic tools for the safety of the astronauts. NASA used Chicago Pneumatic’s air motors in the Apollo space capsules, employing them to rotate the capsules upon their return to Earth, ensuring that the exit hatches faced up and out of the sea, making exit safe for the astronauts.

J.W. Duntley signed the incorporation papers for Chicago Pneumatic Tool Company in New Jersey in December of 1901. More than one hundred years ago, he could not have known that the tools his company crafted would help to build at least four of the “Top Ten Construction Achievements” of the 20th century. Nevertheless, perhaps he did realize, all those years ago, that the brand he built and the commitment to quality he instilled would make CP tools the first choice of generations of people around the world.

Table of Contents

Percussion Tool Safety 4

Breakers—4-Bolt 6

Rivet Busters 9

Spike Drivers 12

Clay Diggers & Picks 12

Scabblers 13

Combi Drills / Hammers 14

Sinker Drills 15

Chipping Hammers 16

Tampers 21

Pumps 22

Vibrators 24

Cut-off Saw 24

Core Drill 25

Air Line Accessories 26

Compressors 27

RCP Compressors 32

Aftermarket 33

Gas Powered Breakers 34

Chisels 36

Hydraulic Tools 37

RX Hydraulic Breakers 44

Generators 50

Percussion Tool Safety

Riveting and chipping hammers, demolition tools, rock drills, tampers and rammers

The goal of Chicago Pneumatic is to produce tools that help you work safely and efficiently. The most important safety device for this or any tool is the operator. Care and good judgment are the best protection against injury.

All possible hazards cannot be covered here, but we have tried to highlight some of the most important ones.

Before operating any Chicago Pneumatic tool, always read the safety instructions that accompany each tool. All Chicago Pneumatic tools supplied with retainers and guards should have these parts properly secured in place during operation.

For Additional Safety Information Consult:

• Other documents and information packed with the tool• Your employer, union and/or trade association• U.S. Department of Labor (OSHA); Council of the European Communities and/or local codes.• “Safety Code for Portable Air Tools” (ANSI B186.1) is available from: American National Standards Institute, Inc., 11 W. 42nd Street, New York, NY 10036• “Safety Requirement for hand-held non-electric power tools” is available from: European Committee for Standardization, Rue de Stassart 36, 1050 Brussels, Belgium.

Air Supply and Connection Hazards

• Air under pressure can cause severe injury.• Always shut off air supply, drain hose of air pressure and disconnect tool from air supply when not in use, before changing accessories or when making repairs.• Never direct air at yourself or anyone else.• Whipping hoses can cause serious injury. Always check for damaged or loose hoses and fittings.• Do not use quick disconnect couplings at tool. See instructions for correct setup.• Whenever universal twist couplings are used, lock pins must be installed.• Do not exceed maximum air pressure of 90 psi or as stated on tool nameplate.

Projectile Hazards

• Always wear impact-resistant eye and face protection when involved with or near the operation, repair or maintenance of the tool or when changing accessories on the tool.• Be sure all others in the area are wearing impact-resistant eye and face protection.• Never operate a tool unless the accessory is retained in the tool with a proper retainer. Please refer to the appropriate parts list.• To avoid injury, retainer parts must be replaced when they become worn, cracked or distorted.• Wear a safety helmet.

4

Operating Hazards

• To prevent damage to both tool and accessory, accessory must be held firmly against the work surface before tool is throttled.• Always shut off the air supply, relieve hose of air pressure and disconnect tool from air supply when changing accessories.• Avoid direct contact with accessory and work surface during and after work as they become heated and sharp.• Wear gloves to protect hands.• Operators and maintenance personnel must be physically able to handle the bulk, weight and power of the tool.• Holding the accessory with the free hand can be a source of vibration exposure or injury.• To avoid injury from entanglement, do not wear loose clothing when using a rock drill.• Wear safety shoes, especially when collaring steels or tamping.• Only use the machine for the jobs for which it is intended.

Accessory Hazards

• Never use any chisel as a hand struck tool. They are specifically designed and heat-treated to be used only in air hammers.• Select the correct shank and retainer for the tool being used.• Never use dull accessories, as they require excessive work pressure and can break from fatigue.• Never cool a hot accessory in water. Brittleness and early failure can result.• Chicago Pneumatic tools and accessories must not be modified in any way.• Chicago Pneumatic percussion tools are not intended for use with any accessories that are not listed in the catalog.• Accessory breakage or tool damage may result from prying. Take smaller bites to avoid getting struck.

Workplace Hazards

• Slipping, tripping and falling are major causes of serious injury or death. Be aware of excess hose left on the walking or work surface.• High sound levels can cause permanent hearing loss. Use hearing protection as recommended by your employer or OSHA regulation (see 29 CFR part 1910).• Maintain a balanced body position and secure footing.• Repetitive work motions, awkward positions and exposure to vibration can be harmful to hands and arms. If numbness, tingling, pain or whitening of skin occurs, stop using the tool and consult a physician.• Avoid inhaling dust or handling debris from the work process that can be harmful to your health.• Proceed with care in unfamiliar surroundings. Hidden hazards may exist, such as electric or other utility lines.• Chicago Pneumatic tools are not intended for use in explosive atmospheres and are not insulated for contact with electric power sources.• A used machine shall be treated and disposed of in such a way that the greatest possible part of the material can be recycled and the influence on the environment is kept as low as possible.

5

Breakers — 4-Bolt High Performance Models

Model Part number Standard hex chuck size

(in)

Retainertype

Length

(in)

Weight

(lb)

Shipping weight

(lb)

CP 0112—30-pound class—air consumption at 90 psi: 45 cfm

CP 0112 8900 0030 23 1 x 41/4 Latch 20 30 36

CP 0112 EX 8900 0030 24 1 x 41/4 Latch 303/8 33 39

CP 0112 S 8900 0030 25


CP 1210 8900 0030 01 1 x 41/4 Latch 211/8 44 47

CP 1210S 8900 0030 03 1 x 41/4 Latch 211/8 48 49

CP 1210S 8900 0030 09 11/4 x 6 Latch 23 49

CP 1210S 8900 0030 07 11/8 x 6 Latch 23 49

CP 1210 SVR 8900 0030 05 1 x 41/4 Latch 231/2 51 57

CP 1210 SVR 8900 0030 08 11/8 x 6 Latch 251/2 55

CP 1210 SVR 8900 0030 10 11/4 x 6 Latch 251/2 55


CP 1230 T022073 11/8 x 6 Latch 261/2 65 66

CP 1230 S T022158 11/8 x 6 Latch 261/2 68 68

CP 1230 SVR T024227 11/8 x 6 Latch 271/2 76 81

CP 1230 T022074 11/4 x 6 Latch 261/2 65 66

CP 1230 S T022159 11/4 x 6 Latch 261/2 68 68

CP 1230 SVR T024239 11/4 x 6 Latch 271/2 76 81


CP 1240 T022075 11/8 x 6 Latch 283/4 83 89

CP 1240 S T022221 11/8 x 6 Latch 283/4 86 92

CP 1240 SVR T024536 11/8 x 6 Latch 30 95 98

CP 1240 T022076 11/4 x 6 Latch 283/4 83 89

CP 1240 S T022222 11/4 x 6 Latch 283/4 86 92

CP 1240 SVR T024535 11/4 x 6 Latch 30 95 98

EX = Extended handle for trench work; S = Silenced models; SVR = Silenced Vibration + reduced models

66

CP Four-bolt breakers require minimal servicing to maintain peak operating efficiency over extended periods of rugged use.

Oversized springs, side bolts and anvil minimize repairs.

CP Breakers can be ordered with mufflers, or mufflers can be purchased separately.

Breakers

7

Breakers — 4-Bolt High Performance Models

CP 1230 and CP 1240

The CP 1230 (60-pound class) and CP 1240 (90-pound class) demolition tools are engi-neered to deliver the power and durability necessary for a variety of construction and plant maintenance applications such as breaking heavy and reinforced concrete, frozen ground, asphalt, boulders and pavement.

Features• Alloy steel forgings provide excellent durability• Four-bolt backhead design withstands rugged use• Integral oiler provides continuous lubrication• Heavy-duty front headsprings reduce reaction back to operator• Reversible piston reduces maintenance cost• Air inlet swivel for easy maneuverability• CP 1230S and CP 1240S are equipped with silencers• Vibration reduced handle (SVR) available on the CP 1230 SVR and CP 1240 SVR

Vibration reduced models (VRS)are also silenced.

1210 SVR 1230 SVR 1240 SVR

Breakers can be ordered with mufflers or mufflers can be

purchased separately.

CP1210S

Standard model CP 1210, 1230 and 1240

CP 0112 and CP 1210

The CP 0112 (30-pound class) and CP 1210 (35-pound class) demolition tools are light-weight yet rugged. They’re designed for light to medium construction and plant maintenance work such as demolition of floors, pavement, bridge maintenance, asphalt, frozen ground and masonry walls. They’re very popular for bridge deck jobs. CP 0112 EX has an extend-ed handle for trench work.

Features• Alloy steel forgings provide excellent durability• Four-bolt backhead design withstands rugged use• Integral oiler provides continuous lubrication• Heavy-duty front headsprings on CP 1210 reduce reaction back to operator• CP 1210S is equipped with a silencer to reduce sound level• Vibration reduced handle (SVR) is available on the CP 1210 SVR

Replacement Parts

8

Contents of Side Bolt Kits

ModelCP 1210

(Steel spring) 1”

CP1210 (PU spring)

1-1/8” and 1-1/4”CP 1230 CP 1240

Kit article no. 3303 0050 44 3303 0050 45 3303 0050 56 3303 0050 57

Contents

2 x side bolt R 110217 R 110217 R 047970 F 037790

2 x nut - side bolt R 110218 R 110217 R 047970 F 037789

2 x lock washer - nut R 041073 R 041073 R 090584 R 096059

2 x front head spring R 093698 3303 0050 33 R 047971 R 092915

Product CP 1210 CP 1230 CP 1240

Contents

Contents of Latch Kits

Retainer latch kits include: latch, latch bushing, bolt or pin, and other parts needed to safely and easily replace worn or broken latches

Side bolt kits include: two each of side rod bolts, nuts, springs and lock washers

Breakers

Pound for pound, there is no hammer with more hitting power than a rivet buster. Even a paving breaker would need to be at least twice as heavy to deliver an equivalent blow. This super-power can still be controlled thanks to low blow frequency and teasing throttle. That’s why the rivet buster is one of the favor ite tools of demolition contractors in the US. Users have discovered many new applications for rivet busters for working in both concrete and steel. No longer is the bus-ter used exclusively by iron workers for form-ing and cutting rivets, but it has now found its way into the hands of operators who need the most powerful tool for the job.

Concrete applications

• Bridge deck work, where weight of breakers is restricted

• De-capping foundation pillars, where concrete is very hard

• Medium to heavy concrete demolition • As an alternative to paving breakers where high

hitting power is required but applied in a restrained space or working horizontally

Metal applications

• Cutting and removing large rivets and bolts with narrow chisels and backout punch, or other spe-cial steel and accessories

• Cutting metal tanks or plates (3/16” thick, 5 mm) with ripper chisel

• Industrial applications such as foundries or the petrochemical industry with beryllium chisels

9

Special Jumbo Shank steel accessories for rivet busters

Rivet Busters for both metal and concrete applications

River Busters

“D” handle

Open grip handle

Rubber bumper3303 0051 03

Part no. Model Weight (lb)

Blows per minute

(bpm)

Cylinder stroke

(in)

Length (in)

Air consumption

(cfm)

Air inlet (in)

Chuck size (Jumbo Shank)

Handle Cylinder

8900 0001 49 4608 P 30 1080 8 23 45 1/2 .890” x 1.125” Taper Open grip-Outside trigger Short cylinder

8900 0001 50 4611 P 33 720 11 26 45 1/2 .890” x 1.125” Taper Open grip-Outside trigger Long cylinder

8900 0001 51 4608 D 31 1080 8 23 45 1/2 .890” x 1.125” Taper “D” handle-Inside trigger Short cylinder

8900 0001 52 4611 D 34 720 11 26 45 1/2 .890” x 1.125” Taper “D” handle-Inside trigger Long cylinder

10

Originally designed for cutting and forming metal rivets, the CP buster is now used for concrete demolition and has become one of the stars of the CP range. It has a low frequency blow with hitting power equivalent to a paving breaker twice its weight. The new CPS includes a stepped piston and step cylinder to prevent accidental ejection of the piston.

• Teasing throttle for progressive hitting frequency gives better control of such a powerful machine

• Special Boyer valve makes the cylinder stroke effectively longer for more hitting power

• Boyer valve’s high quality design makes the blow more consistent

• Forged steel handle for long life in rugged condi-tions

• Stepped piston of hardened steel

• New buffer ring is now 90 durometer rubber for extra life

• Stepped piston to prevent accidental ejection of the piston

• Choice of cylinders: 11” cylinder (720 bpm) 8” cylinder (1080 bpm)

• Choice of handle: Open grip with outside trigger “D” handle with inside trigger

• 1/2 ” inlet bushing

With each buster, it is recommended that you also purchase these additional consumable items: a rubber bumper (3303 0051 03), lower sleeve (P072333), upper sleeve (P156988), retainer spring (P073942) and whip hose (9246 0203 64).

4608 P - 8” OPEN HANDLE 4608 D - 8” D-HANDLE

CPS Control Power System The wear indicating groove (l) on the lower sleeve indicates that the bumper is completely worn out and needs to be replaced.

When the bumper is 75% worn out, the bleeding ports (J) are opened due to the outward movement of the upper and lower sleeves, causing the piston to stop in its lower position and the air to the exhaust above retainer.

Continuing to use the buster when the auto-matic stop function has triggered may cause damage to the sleeves and possibly the cylinder.

A. Lower sleeve B. Bumper C. Upper sleeve

Rivet Busters with CPS

Rivet Busters with CPS

4611 P - 11” OPEN HANDLE 4611 D - 11” D-HANDLE

Key features

Description Type of Part Number Tip width/ Length Weight body Bladesize overall (in) (in) (lbs.)

Moil 3083 4140 00 10 2point 3083 4140 10 12 2 1/2

3083 4140 20 18 4

Narrow 3083 4141 00 1 10 2Chisel 3083 4141 10 1 12 2 1/2

3083 4141 20 1 18 4

Loose 3083 4142 00 1 1/8 10 2Rivet 3083 4142 10 1 1/8 12 2 1/2

Buster 3083 4146 20 1 1/8 18 4

Tight 3083 4145 00 1 1/8 10 2Rivet 3083 4145 10 1 1/8 12 2 1/2

Buster 3083 4145 20 1 1/8 18 4

Drift 3083 4143 00 7/8 dia. 7 1/2 1 1/2

PinDriver

Ripper 3083 4144 00 9 1 3/4

Backout 3083 4148 10 5/8 10 1 3/4

Punch 3083 4148 20 5/8 12 1 3/4

3083 4148 40 3/4 10 2 3083 4148 50 3/4 12 2 3/4 3083 4148 70 7/8 10 2 3/4

3083 4148 80 7/8 12 3

Line oilers

Water separator

HEAVY DUTY RIVET BUSTER STEEL

Consumables and accessories Consumables and accessories for rivet busters using jumbo steels

Blade width Length o/a Weight Price

inches inches lbs. $

3083 4140 00 10 2 28.05

3083 4140 10 12 2.1/2 33.65

3083 4140 20 18 4 46.00

3083 4141 00 1 10 2 28.05

3083 4141 10 1 12 2.1/2 33.65

3083 4141 20 1 18 4 46.00

3083 4142 00 1.1/8 10 2 31.40

3083 4142 10 1.1/8 12 2.1/2 37.00

3083 4146 20 1.1/8 18 4 57.20

3083 4145 00 1.1/8 10 2 44.90

3083 4145 10 1.1/8 12 2.1/2 53.85

3083 4145 20 1.1/8 18 4 67.30

3083 4143 00 7/8 dia. 7.1/2 1.1/2 53.85

3083 4144 00 9 1.3/4 50.50

3083 4147 00 1/2 9.3/4 1.1/2 35.90

3083 4147 10 5/8 9.3/4 1.3/4 38.15

3083 4147 20 3/4 9.1/2 1.3/4 38.15

3083 4147 30 3/4 12 2.1/2 35.90

3083 4147 40 7/8 9.1/2 2 38.15

3083 4147 50 7/8 12 2.3/4 37.00

3083 4147 60 1 9.1/2 2.1/2 40.40

3083 4147 70 1 12 2.3/4 47.10

Loose

Rivet

Buster


Moil

Point

Narrow

Chisel

Type of Working EndType of

bodyPart Number

Jumbo 11X

Tight

Rivet

Buster

Drift Pin

Driver

Backout

Punch

Ripper

3/4

7/81.1/8

2.3/8

1.3/4

- 7 -



3083 4140 00 10 2 28.05

3083 4140 10 12 2.1/2 33.65

3083 4140 20 18 4 46.00

3083 4141 00 1 10 2 28.05

3083 4141 10 1 12 2.1/2 33.65

3083 4141 20 1 18 4 46.00

3083 4142 00 1.1/8 10 2 31.40

3083 4142 10 1.1/8 12 2.1/2 37.00

3083 4146 20 1.1/8 18 4 57.20

3083 4145 00 1.1/8 10 2 44.90

3083 4145 10 1.1/8 12 2.1/2 53.85

3083 4145 20 1.1/8 18 4 67.30

3083 4143 00 7/8 dia. 7.1/2 1.1/2 53.85

3083 4144 00 9 1.3/4 50.50

3083 4147 00 1/2 9.3/4 1.1/2 35.90

3083 4147 10 5/8 9.3/4 1.3/4 38.15

3083 4147 20 3/4 9.1/2 1.3/4 38.15

3083 4147 30 3/4 12 2.1/2 35.90

3083 4147 40 7/8 9.1/2 2 38.15

3083 4147 50 7/8 12 2.3/4 37.00

3083 4147 60 1 9.1/2 2.1/2 40.40

3083 4147 70 1 12 2.3/4 47.10

Loose

Rivet

Buster


Moil

Point

Narrow

Chisel


bodyPart Number

Jumbo 11X

Tight

Rivet

Buster

Drift Pin

Driver

Backout

Punch

Ripper

3/4

7/81.1/8

2.3/8

1.3/4

- 7 -



3083 4140 00 10 2 28.05

3083 4140 10 12 2.1/2 33.65

3083 4140 20 18 4 46.00

3083 4141 00 1 10 2 28.05

3083 4141 10 1 12 2.1/2 33.65

3083 4141 20 1 18 4 46.00

3083 4142 00 1.1/8 10 2 31.40

3083 4142 10 1.1/8 12 2.1/2 37.00

3083 4146 20 1.1/8 18 4 57.20

3083 4145 00 1.1/8 10 2 44.90

3083 4145 10 1.1/8 12 2.1/2 53.85

3083 4145 20 1.1/8 18 4 67.30

3083 4143 00 7/8 dia. 7.1/2 1.1/2 53.85

3083 4144 00 9 1.3/4 50.50

3083 4147 00 1/2 9.3/4 1.1/2 35.90

3083 4147 10 5/8 9.3/4 1.3/4 38.15

3083 4147 20 3/4 9.1/2 1.3/4 38.15

3083 4147 30 3/4 12 2.1/2 35.90

3083 4147 40 7/8 9.1/2 2 38.15

3083 4147 50 7/8 12 2.3/4 37.00

3083 4147 60 1 9.1/2 2.1/2 40.40

3083 4147 70 1 12 2.3/4 47.10

Loose

Rivet

Buster


Moil

Point

Narrow

Chisel


bodyPart Number

Jumbo 11X

Tight

Rivet

Buster

Drift Pin

Driver

Backout

Punch

Ripper

3/4

7/81.1/8

2.3/8

1.3/4

- 7 -



3083 4140 00 10 2 28.05

3083 4140 10 12 2.1/2 33.65

3083 4140 20 18 4 46.00

3083 4141 00 1 10 2 28.05

3083 4141 10 1 12 2.1/2 33.65

3083 4141 20 1 18 4 46.00

3083 4142 00 1.1/8 10 2 31.40

3083 4142 10 1.1/8 12 2.1/2 37.00

3083 4146 20 1.1/8 18 4 57.20

3083 4145 00 1.1/8 10 2 44.90

3083 4145 10 1.1/8 12 2.1/2 53.85

3083 4145 20 1.1/8 18 4 67.30

3083 4143 00 7/8 dia. 7.1/2 1.1/2 53.85

3083 4144 00 9 1.3/4 50.50

3083 4147 00 1/2 9.3/4 1.1/2 35.90

3083 4147 10 5/8 9.3/4 1.3/4 38.15

3083 4147 20 3/4 9.1/2 1.3/4 38.15

3083 4147 30 3/4 12 2.1/2 35.90

3083 4147 40 7/8 9.1/2 2 38.15

3083 4147 50 7/8 12 2.3/4 37.00

3083 4147 60 1 9.1/2 2.1/2 40.40

3083 4147 70 1 12 2.3/4 47.10

Loose

Rivet

Buster


Moil

Point

Narrow

Chisel


bodyPart Number

Jumbo 11X

Tight

Rivet

Buster

Drift Pin

Driver

Backout

Punch

Ripper

3/4

7/81.1/8

2.3/8

1.3/4

- 7 -

11

RedX Hose 8900 0050 08

Part no. Description

P 072 333 Lower sleeve

P 156 988 Upper sleeve

3303 0051 03 Rubber bumper

P 073 942 Retainer Spring (standard

9246 0203 72 Air swivel 1/2” NPT

9246 0203 69 Lubricator comp 3/4” NPT - 5oz



8900 0050 01 Water separator 3/4” NPT thread

8099 0202 43 Airoline oil 1L

9246 0203 64 Whip hose with swivel 1/2” NPT

9246 0203 61 Whip hose w/5 oz oiler and swivel

9246 0203 91 Whip hose w/11 oz oiler and swivel

Spike Drivers

Chicago Pneumatic spike drivers are rugged, powerful tools which can be used for driving spikes in railroad, construction and plant maintenance applications.

Model Part number Length

(in)

Max head diameter

(in)

Weight

(lb)

Shippingweight

(lb)

CP 1230—Air consumption at 90 psi: 63 cfm

CP 1230 SPDR T021612 241/2 17/8 60 65

CP 1230 S SPDR T021613 241/2 17/8 60 65


CP 1240 SPDR T021042 241/2 17/8 81 86

CP 1240 S SPDR T021041 241/2 17/8 81 86

Clay Diggers and Picks

Clay diggers and picks are well suited for trenching and tunneling. Their light weight makes them ideal for overhead work and light demolition.

Model Part number

Standardhex chuck

(in)

Bore andstroke

(in)

Throttletype

Length

(in)

Weight

(lb)

CP 0111 —Air consumption at 90 psi: 45 cfm, 3/8” (NPT) air inlet thread

CP 0111 CHIT 8900 0001 41 7/8 x 31/4 1.63 x 3.5 inside trigger 221/2 29

CP 0111 CHLA 8900 0001 20 1 x 41/4 1.63 x 3.5 outside trigger 221/2 29

CP 0222—Air consumption at 90 psi: 44 cfm, 1/2” (NPT) air inlet thread

CP 0222 CHIT 8900 0001 21 7/8 x 31/4 1.6 x 3.38 inside trigger 191/2 22

CP 0222

CP 1230 SPDR

• Heat-treated alloy steel components for excellent durability• Spike driver front hood • Built in lubricator

CP 1240 SPDR

• Lightweight and compact for easy handling• High power-to-weight ratio• Spike driver front hood • Built in lubricator

CP 0111

• Heat-treated alloy steel components for excellent durability• Latch retainer• High power-to-weight ratio

CP 0222

• Lightweight and compact for easy handling• High power-to-weight ratio• Latch retainer

CP 1240 S SPDR

CP 1230 S SPDR

12

Spike Drivers, Clay Diggers and Picks

CP 0111

Scabblers

Scabblers are ideal for cleaning and roughing concrete and construction joints. They can also be used to produce ornamental or contrasting finishes on building structures.

Model Part number bpmper piston

Bore

(in)

Stroke

(in)

Weight Length Height (pistonsextended)

(in)

Width

(in)

Number/typeof pistons

All models—Air consumption at 90 psi: 29 cfm, 1/2” (NPT) air inlet thread

CP 0006* T022137 3000 1 1 10 16 7 4 Three 4-point carbide tipped

CP 0066* T024412 3000 0 1 10 11 5 2 3

*Use whip hoses on page 11 for Rivet Busters

Replacement pistons Model Part number

CP 0006 F064604

CP 0066 R145921

Piston caps(order one for each replacement piston) Model Part number

CP 0006 F826706

CP 0066 R147614

Replacement parts

13

Scabblers

CP 0006

• Lightweight, compact tool with contoured grip handle reduces operator fatigue and increases output• Tungsten carbide-tipped pistons last longer and are easily replaced• Back head grip gives in-line thrust• Chamfered cylinder block increases visibility of the work piece permitting close operation in tight corners

CP 0066

• Lightweight, compact tool with contoured grip handle reduces operator fatigue and increases output• Tungsten carbide-tipped pistons last longer and are easily replaced• Chamfered cylinder block increases visibility of the work piece permitting close operation in tight corners

CP 0006

CP 0009

CP 0014

Combi Drills / Hammers

All Models

• Excellent power-to-weight ratio helps drill holes faster and easier than comparable electric rotary hammers• Built-in oiler provides continuous lubrication• Teasing throttle for precise control• Rotation release button converts tool to a hammer (except on CP 0009AC)• Cushioned piston for smooth operation and long tool life• Muffler available to reduce noise

CP 0009

• Right hand rotation• With an adaptor, can be used with electric hammer drill bits• Spline version available• Adapter (R137586) round to SDS

CP 0014

• Superior drilling rates• Greater drilling capacity compared to plug hole drills• Designed for production drilling of small holes

Model Partnumber

Netweight

(lb)

Overalllength

(in)

Typeof chuck

(in)

Chuck size(in)

CP 0009—Air consumption at 90 psi: 20 cfm, 3/8” (NPT) air inlet thread

CP 0009 A T022083 8 143/4 round shank 3/4 x 33/4

CP 0009 AC* Z0027413 8 143/4 round shank 3/4 x 33/4

CP 0009 F T022511 8 143/4 spline drive

CP 0014 RR—Air consumption at 90 psi: 32 cfm, 3/8” (NPT) air inlet thread

CP 0014 RR T022173 15 181/2 spring hex shank 7/8 x 31/4

* without stop rotation, round shank steels, eliminate rotation.

Drilling rates in hard rock and concrete(use as guide only)

Model Drill rate(in/min)

Hole diameter(in)

CP 0009 12 11/4

CP 0014 RR 18 13/4

Mufflers Model Part no.

CP 0009 A F815350

CP 0009 AC F826972

CP 0009 F F815350

CP 0014 RR F827044

These versatile tools are both a drill and a chipping hammer. A push of the rotation release button easily and quickly converts the tool to a hammer.

The CP 0009 and CP 0014RR rotary hammers are designed for a wide variety of construction and maintenance applications such as driving or setting masonry anchors and drilling holes in concrete, bricks or rock. As a hammer, these tools can be used for chipping, scarifying, scaling and cleaning welds.

14

Rock Drills

CP 0032A

Sinker Drills

All Models

• Forged steel housings withstand rugged use• Cushioned piston reduces shock• Multiposition throttle for easy starting of holes• Blower lever for deep hole cleaning on CP 0032 and CP 0069• Integral oiler provides continuous lubrication• 3/4” (NPT) air inlet swivel improves maneuverability• Double-grip handles • Left hand rotation

CP 0022

30-pound classThe CP 0022 provides drilling capability for holes up to 13/4” diameter, 8 feet deep. This is the ideal choice where a lightweight and powerful tool is needed in public works, utilities and drilling from scaffolding. Also the correct choice where air supply is limited. CP 0022 can also be equipped with 3/4” x 41/4” bushing and spring

CP 0032A

45-50-pound classChoose the CP 0032A for holes up to 2” diameter and 10 feet deep. A top performer in its class, the CP 0032A is highly effective in general excavation work, quarry drilling, bench mining and other jobs requiring a sinker drill in the 45-pound class. The tool’s durable “beavertail” retainer helps it deliver increased contact and reduces collar wear.

Use with part number R147457 - Water Kit for use with flushing water

CP 0069

60-pound classThe CP 0069 is suited for drilling 21/2” diameter holes 20 feet deep. The heavy-duty CP 0069 sinker is a hard-hitting tool that combines high drilling speed with excellent hole cleaning ability. Its trouble-free “beavertail” retainer provides greater front-end durability and increased collar contact to reduce wear.

Model Part number

Netweight

(lb)

Overall lengthwith retainer

(in)

Standard hex. chuck size

(in)

CP 0022—30-pound class—Air consumption at 90 psi: 56 cfm

CP 0022 8900 0020 01 28 197/8 7/8 x 31/4

CP 0022 8900 0020 02 28 197/8 7/8 x 41/4

CP 0032—45- to 50-pound class—Air consumption at 90 psi: 103 cfm

CP 0032A .87 T022318 54 22 7/8 x 31/4

CP 0032A .87 A T022117 54 23 7/8 x 41/4

CP 0032A-1 T022319 54 23 1 x 41/4

CP 0069—60-pound class—Air consumption at 90 psi: 130 cfm

CP 0069 T006661 64 241/4 7/8 x 41/4

CP 0069 T022259 64 241/4 1 x 41/4

CP 0069 - wet T025423 64 241/4 7/8 x 41/4

Comfort handle options

CP 0022, CP 0032A, and CP 0069 can also be equipped with a comfort handle (order kit: R154915).

Model Drill rate(in/min)

Hole diameter (in)

CP 0022 6.0 15/8

CP 0032 9.0 13/4

CP 0069 10.2 13/4

Drilling rates in hard rock(use as guide only)

Chicago Pneumatic sinker drills are ideal for a range of drilling applications. Their streamlined design incorporates smooth contours, a side exhaust and a “flat back” that makes them easy to handle in quarry, mine, drilling and doweling work. The design also provides a main valve and cylinder-porting concept that helps maintain constant drilling speed throughout a long service life. Working parts are continually protected with an effective lubrication system. Standard and silenced versions are available in a range of weights and sizes to fit any requirement.

15

CP 0022

Model Part number

CP 0032A R125569

CP 0069 R278142

Mufflers

CP 0012 handle based on the well known CP 0009 design

CP 4123 with simplate valve

CP 4125 now has a unique ring valve design as standard

CP 4125 special heat treated cylinders with chrome plated bores

for extra durability

CP 4130 four bolt flange for in-creased durability, strength and ease

of service

0012, a new 12 lb. hammer for light chipping, and additional features on the classics – CP 4123 and CP 4125 hammers – for extra toughness and reliability.

Chipping Hammers

With 2”, 3” and 4” cylinder options, Chicago Pneumatic offers a very complete range of chipping hammers for all types of con struction and industrial applications. Introducing CP

CP 0012

CP 4123

CP 4130

• Locking mechanism with four high strength ½” bolts• ”D” handle with outside trigger and extra safety mechanism• Muffler assembly as standard• Simplate valve for smooth operation• Strong and reliable• Available in 3” or 4” cylinder stroke versions• Choice of bushing: .680” Round chisel rotates freely .580” Hex prevents chisel rotation

• Powerful, yet compact and lightweight• Rugged construction, hardened steel cylinder and handle• Teasing throttle for precise control• Open grip handle with self closing outside trigger

• Available in 2”, 3” or 4” cylinder stroke versions• Choice of bushing: .680” Round chisel rotates freely .580” Hex prevents chisel rotation

• Classic simplate valve• Heat treated cylinder• Now with spline lock instead of clip locking mechanism

• Unique ring valve as standard for harder blow in tough applications or dirty environments• Chrome plated cylinder for extra durability• Spline locking to prevent loosening of handle or cylinder

CP 4125

CP 4123 and CP 4125

Chipping Hammers

CP 4132

Chipping hammers for construction and industrial applications

Part no. Model Old model name Weight

(lb)

Cylinder stroke

Length

(in)

Blows per minute (bpm)

Air consumption

(cfm)

Muffler included as standard

Chuck size

(in)

8900 0001 02 CP 0012 2ßR – 12 2 16 2600 20 yes .680” Rnd

8900 0001 03 CP 0012 2H – 12 2 16 2600 20 yes .580” Hex

8900 0001 04 CP 4123 2R CP 4123 PYRA 13 2 127/8 2400 25 – .680” Rnd

8900 0001 05 CP 4123 2H CP 4123 PYRE 13 2 127/8 2400 25 – .580” Hex

8900 0001 06 CP 4123 3R CP 4123 PYSA 141/4 3 147/8 1920 26 – .680” Rnd

8900 0001 07 CP 4123 3H CP 4123 PYSE 141/4 3 147/8 1920 26 – .580” Hex

8900 0001 08 CP 4123 4R CP 4123 PYTA 151/2 4 151/2 1500 27 – .680” Rnd

8900 0001 09 CP 4123 4H CP 4123 PYTE 151/2 4 151/2 1500 27 – .580” Hex

8900 0001 10 CP 4125 2R CP 4125 PALA 13 2 131/4 2400 26 – .680” Rnd

8900 0001 11 CP 4125 2H CP 4125 PALE 13 2 131/4 2400 26 – .580” Hex

8900 0001 12 CP 4125 3R CP 4125 PAMA 141/4 3 141/4 1920 27 – .680” Rnd

8900 0001 13 CP 4125 3H CP 4125 PAME 141/4 3 141/4 1920 27 – .580” Hex

8900 0001 14 CP 4125 4R CP 4125 PANA 151/2 4 151/4 1500 28 – .680” Rnd

8900 0001 15 CP 4125 4H CP 4125 PANE 151/2 4 151/4 1500 28 – .580” Hex

8900 0001 16 CP 4130 3R CP 4130 3RO 181/2 3 161/2 1920 26 yes .680” Rnd

8900 0001 17 CP 4130 3H CP 4130 3HO 181/2 3 161/2 1920 26 yes .580” Hex

8900 0001 18 CP 4130 4R CP 4130 4RO 191/2 4 173/4 1500 27 yes .680” Rnd

8900 0001 19 CP 4130 4H CP 4130 4HO 191/2 4 173/4 1500 27 yes .580” Hex

9245 9998 00 CP 4132 3R 15 3 17 1800 33.23 .680” Rnd

9245 9997 99 CP 4132 3H 15 3 17 1800 33.23 .580” Hex

9245 9998 98 CP 4132 4R 15 4 17 1800 33.23 .680” Rnd

9245 9998 80 CP 4132 4H 15 4 17 1800 33.23 .580” Hex

3/8” air inlet. All CP hammers are supplied with oval collar retainer as standard. More retainer options are available on page 20.

CP 0012

The CP 0012 is the new addition to the CP range of pneumatic hammers for light chipping and scaling duties. Since the CP 0012 is light and has medium hitting power, it is very easy to handle and control for more precisejobs. Typical applications include alteration work, hole making and trimming.

CP 4123

The most popular CP chipping hammer of all times, the CP 4123 is used for a wide variety of construction and industrial applications, from light to medium chipping to heavy cutting. Choose the cylinder size that best suits your particular application.

CP 4125

The extra features of the CP 4125 make it more suitable for tough constructionand industrial applications, including foundries, shipyards, refineries, or fabrication shops. Even in hot, dirty working conditions, the reliable CP 4125 will consistently hit hard and last longer than conventional hammers.

CP 4130

The CP 4130 hammer is designed to tackle punishing jobs with the hard hitting power that you expect from CP. It is used for medium-duty to heavy-dutychipping, cutting and trimming operations. The four bolt handle provides higher air flow and durability.

CP 4132

A durable 4-bolt chipping hammer with inside trigger and standard retainer.Available in two cylinder sizes to suite your particular application.

17

18

Chipping Hammers

Model Part Number Air consumption

(CFM)

Blowsper minute

Chuck size

(in)

Length

(in)

Net weight

(lb)

CP 0017 8900 0001 36 32 2200 .680 round 151/4 19

CP 0017 8900 0001 37 32 2200 .580 hex 151/4 19

Model Part Number Bore and Stroke(in)

Blows per minute Bushing size(in)

Overall length*(in)

Net weight(lb)

CP 4131 3R 8900 0001 33 3 1900 .680 round 17 1/2 19

CP 4131 3H 8900 0001 34 3 1900 .580 hex 17 1/2 19

Chipping Hammers New Models

Z8389857 Ball type retainer safely secures accessories

CP 4131 features a thread on ball type retainer as standard

NEW! CP 4131

• Lightweight • Easy to use and maintain• Choice of bushing: .680” Round chisel rotates freely .580” Hex prevents chisel rotation• Ball type retainer• D handle with outside trigger

NEW! CP 0017

• Designed for years of trouble-free service • Closed aluminum handle with inside trigger for

maximum effectiveness and operator comfort• Oil-resistant neoprene exhaust deflectors• Available with choice of .580 or .680 round

bushings

Moil point

Wide chisel

Wide chisel

Bushing tool

Steel for chipping hammers and clay diggers

Chipping hammer steel (CP 0012, CP 4123, CP 4125, CP 4130, CP 4131, CP 4132)Hex .580” shank Round .680” shank

Description Tip width/ blade size

Length overall

OVAL collarPart no.

ROUND collarPart no.

OVAL collarPart no.

ROUND collarPart no.

Clay digger steel (CP 0111 and CP 0222)CP 0111—Hex 1” x 41/4” shank CP 0222—Hex 7/8” x 31/4” shank – CP 0222

Description Tip width/ blade size

(in)

Length overall

(in)

Flat to flat

Part no.

Tip width blade size

(in)

Length overall

(in)

Flat to flat

Part no.

Moil point 15 3083 4030 00 14 3083 4050 00

18 3083 4030 10 18 3083 4050 10

24 3083 4030 20 24 3083 4050 20

Narrow chisel 17/8 15 3083 3309 00 1 14 3083 3303 00

11/8 18 3083 4031 10 1 18 3083 4051 10

11/8 24 3083 4031 20 1 24 3083 3304 00

Wide chisel 3 x 2 15 3083 3310 00 3 x 11/4 14 3083 3305 00

3 x 2 18 3083 4032 10 3 x 11/4 18 3083 4052 10

3 x 2 24 3083 4032 20 3 x 11/4 24 3083 4052 20

Bushing tool 2 sq 9 3083 4036 00 2 sq 9 3083 4056 00

Use the most effective steel for your application. Shown below are a selection of the most common types of steel used for the hammers presented in this brochure. For the complete assortment of air line accessories, see pages 20 and 26.

Other lengths of steel accessories are available upon request. See CP Accessories Price List for ordering numbers.

Other lengths of steel accessories are available upon request. See catalog 9800 0362 93 for ordering numbers.

19

Accessories

Line oilersEconomy-type retainer

Water separatorQuick change retainer

Muffler AT Lug-type retainer

Ball-type retainer

Model Part no. Description

Chipping hammer accessories(CP 0012, CP 4123, CP 4125, CP 4130, CP 4131, CP 4132)

Retainers 9245 9970 02 Economy-type retainer, oval collar

9246 00205 01 Ecomomy-type retainer, round collar

P114062 Quick change retainer, oval collar

P092869 AT Lug-type retainer, oval collar

9245 9983 14 Ball-type retainer, round collar

Retainer springs P135246 Polyurethane

P070994 Wire

P139189 Heavy duty wire

Mufflers P125052 CP 4123/CP 4125 muffler assembly

Hose swivels 9246 0203 70 CP 4123/CP 4125/CP 4132 7/8”-24 inlet thread

9246 0203 71 CP 4130/CP 4131 7/8”-24 inlet thread with 3/8” male pipe thread

9246 0203 72 CP Busters, Tampers, Saw 1/2” NPT air inlet thread

Clay digger accessories (CP 0111 and CP 0222)

Mufflers F814133 CP 0111 muffler assembly

R141765 CP 0222 muffler assembly

Air line accessories

In-line oilers 9246 0203 69 Lubricator 5 oz, w/Universal Couplings

Lubricator 8 oz, w/Universal Couplings

9246 0203 68 Lubricator 11 oz, w/Universal Couplings

Water separator 8900 0050 01 3/4” NPT thread

Air-oil 5 litre

For chipping hammers, clay diggers and air line

LubricatorCP’s Lubricator 43 uses the ejector principle to create controlled lubrication. Pick-up assures oil supply regardless of the lubricator’s position.

Model Part No. Max. working pressure

(psi)

Oil tank volume(pints)

Dosage—free air(lb/feet3)

Weight- empty

(lb)

Air flow range: up to 300 cfm; Pressure drop at 90 psi at max flow: 4 psi

Lubricator 43 8900 0050 07 232 2.75 .6 x 105 - 15 x 105 6.6

20

Accessories

NEW! Lubricator 43

• Accepts mineral or synthetic oil• Fitted with US universal claw couplings• 1” inner hose diameter

Backfill Tampers

AccessoriesBackfill tamper butts

Diameter(in)

Material CP 0003 CP 0004RV

21/2 Aluminum - P138879

5 Aluminum P089008 -

61/4 Aluminum - P089050

6 Iron 3303 0050 82

61/4 Iron 3303 0050 81

Pole Butt Iron 3303 0050 84 3303 0050 83

MufflersDescription Part no.

CP 0003 P126126

CP 0004RV P125807

Tamper butts for CP 0003 and CP 0004

Chicago Pneumatic backfill tampers quickly and effectively compact soil around foundations and other structures and are indispensable for compacting backfill in trenches.

The CP 0003 is well equipped to handle light to medium applicationswhile the CP 0004RV is ideal for heavier jobs.

Model Partnumber

Valvetype

Boreand stroke

(in)

Blows perminute

Net weight

(lb)

Overalllength

(in)

Piston rod

Body dia.(in)

Butt size(in)


CP 0003 T019307 Simplate 117/16 x 6 800 30 52 7/8 5


CP 0004 T022292 Ring 21/4 x 6 780 42 50 1 61/4

21

Tampers

CP 0003 CP 0004

CP 0003 and CP 0004

• Maximum power—slow, powerful blows efficiently and quickly compact all types of backfill, including clay and soils containing high percentages of finely crushed or powdered material• Heat-treated cylinder and chrome plated piston significantly extend tool life• Adjustable packing maintains a positive air seal• Aluminum butt held with clamp screw for quick, easy replacement• Exhaust deflector directs air, moisture and oil away from operator• Integral oiler continuously lubricates tool during operation • Well-balanced, smooth-operating tool is easily guided by one person• 1/2” (NPT) air inlet thread• For quieter operation, optional mufflers are available


CP 0010

Chicago Pneumatic’s CP 0010 and CP 0020 sump pumps are designed for high performance and durability which makes them ideal for removing water from trenches, ditches, manholes, industrial sumps and excavations. Both models will pump down to within only 7/8” from base.

CP 0010 has exhaust pipe 1” NPT x 16” long (S038723).

CP 0020 has exhaust pipe 11/4” NPT x 18” long (C086080).

Caution! CP 0010 and CP 0020 pumps are not intended for pumping flammable fluids and must not be used for doing so.

CP 0010 Performance—Air consumption at 90 psi: 100 cfmTotalHead

(ft)

Discharge rate

40 psi(gal/min)

60 psi(gal/min)

80 psi(gal/min)

90 psi(gal/min)

100 psi(gal/min)

10 160 220 240 245 255

20 140 205 230 240 250

30 120 185 215 230 245

40 90 160 200 215 230

50 60 135 175 195 210

60 10 105 155 175 195

70 - 80 130 150 170

24.3 - 60 95 125 155

90 - - 75 105 125

100 - - 55 75 95

Model Partnumber

Min. water depth

(in)

Overallheight

(in)

Heightw/o valve

(in)

Waterdischarge(NPT-in)

Netweight

(lb)

Min. openingpump will enter

(in)

Air inletthread size

(NPT-in)

Recommended hose size

(in)

Motor

(hp)

CP 0010 T022224 7/8 17 1/2 13 3/4 2 33 8 1/4 x 9 3/4 3/4 3

CP 0020 T022185 7/8 16 11 3/4 2 1/2 58 9 x 11 3/4 1 1 4

CP 0020

CP 0020 Performance—Air consumption at 90 psi: 110 cfmTotal Head

(ft)

Discharge rate

40 psi(gal/min)

60 psi(gal/min)

80 psi(gal/min)

100 psi(gal/min)

10 230 285 325 340

20 195 265 315 330

30 150 245 300 320

40 130 220 280 305

50 100 190 260 280

60 65 165 230 260

70 - 125 200 225

80 - 80 160 190

90 - - - 155

22

Pumps

All Models

• Single-stage centrifugal units driven by powerful vane motors

• Double seals protect bearings and motor from water and mud

• Integral oiler provides continuous lubrication• Integral strainer, air inlet valve• Bronze impeller• Cast-iron housing• Air inlet valve

Sump pumps

Sludge pump

Accessories for CP 0077Part number Description

Inlet Hose Nipple F027762 3” unthreaded x 21/2” BSP

Outlet Nipples R146385 21/2” NPT (both ends)

R146383 21/2” NPT street elbow

Model Part number Maximum suction lift (ft at 90 psi)

Maximumhead(ft)

Dischargeoutlet(NPT)

Air Inletthread size

(NPT)

Recommendedhose size

(in)

Netweight

(lb)


CP 0077 T024005 20** 175** 21/2 3/4 1 152

CP 0077 Performance at 90 psi, zero suction head

Total head(ft)

Discharge rate(gal/min)

25 90

50 78

75 68

100 60

150 48

175 36

CP 0077

• Has no motor or diaphragm to wear out because it operates on venturi/ejector principle • Exhaust muffler reduces sound level

Caution! CP 0077 pumps are not intended for pumping flammable fluids.

** Includes friction head from hose.

23

CP 0077

CP 0077 sludge pumps easily handle water containing 15% solids and particles up to 1” in size. They are suitable for pumping sea water and certain corrosive chemicals.

Concrete Vibrators

Chicago Pneumatic’s CP 2190 heavy duty concrete vibrator is designed for removing air pockets from pourings of low slump concrete in columns, footings, slabs and walls. It has a greater radius of influence which translates to a greater amount of work accomplished in a shorter period of time. And, unlike electric concrete vibrators, there is no chance of shock or need for extension cords.

Model Partnumber

Air consumption

(CFM)

Radius ofinfluence

(in)

Capacity(cu. yds/hr)

Vibrationper

minute

Head dimensions Net weight

(lb)

Length w/o aux. hose

(in)

Averagecfm

Diameter(in)

Length(in)

CP 2190 T019308 65 15 - 16 40 12,000 21/2 133/4 27 118 65

Cut-off Saw

Avoid the daily maintenance associated with gas-powered saws.

The CP 0044 is an extremely durable and powerful air tool driven by a direct drive, 4 hp motor. It is designed to cut a variety of surfaces including concrete, asphalt and stone.

The CP 0044 is engineered for precise balance so less effort is needed to get the job done. A built-in oiler provides continuous lubrication so more time is spent on the job and less time on servicing. Also designed with safety in mind, the CP 0044 features a standard lock-off trigger to help prevent accidental starting. Plus, the blade guard can be operated with one hand.

CP 0044

• Chicago Pneumatic 4 hp motor• One-hand operation blade guard• Integral oiler• Lock-off trigger• Direct drive operation• Two position handle• Well balanced and extremely durable• 1” diameter arbor accepts

industry standard blades

CP 2190

• Variable speed throttle• In-line lubricator• Auxiliary air hose• Locked motor end plates• 1/2” NPT air connection

Model Partnumber

Air consumption

(CFM)

Blade arbordiameter

(in)

No load

(rpm)

Weightwith blade

(lb)

Overall length

(in)

Max. cuttingdepth

(in)

Blade cap (in)

CP 0044 T024421 85 1 4800 28 261/2 4 14

24

Vibrators, Pneumatic Saw


Chicago Pneumatic’s CP 0315 Core Drill is a powerful, hand-held rotary drill with a threaded output shaft onto which a water swivel and core bit can be fitted. It was originally designed for hand cutting holes in reinforced concrete junc-tion boxes for fiber optic cables. It is now being used in many other sectors of the construction industry for cutting holes in concrete, brickwork and stone and where access or position restricts the use of rig-mounted units. It is also ideal for use in hazardous environments where use of electrical tools is forbidden.

Heavy Duty Core Drill

Model Part No. Free speed(rpm)

Outputshaft

Air inletsize(in)

Length

(in)

Weight

(lb)


CP 0315 T024733 750 45/64” - 16 tpi 1/2 bsp 13 14

Core Drill AccessoriesDescription Part no.

Water swivel—45/64” input box thread, 1/2” BSP output pin thread 8900 0050 04

Adapter—convert from 1/2” BSP output pin thread to 11/4” UNC output pin thread 8900 0050 05

25

Core Drill

CP 0315

• Core diameter range: 21/2” to 6”• Powerful 1.2 hp air motor• Self-closing twist throttle operation with one-hand control• Governor controlled motor holds speed at heavy loads while increasing power• Integral oil reservoir ensures correct oiling during use• External grease fitting for easy lubrication• Breast-plate for operator comfort during horizontal drilling• Light weight promotes stable operation• Optional adapter (C013048) is available for standard drilling operation

Air line

Description Part no.

CP oiler & separator kit 9245 0204 13

CP water separator 8900 0050 01

lubricator 43 1” NPT 8900 0050 07

CP Red-X hose set US 3/4 ” x 50’ 8900 0050 08

whip hose - 10FT 7/8” - 24 swivel (TEX 317 - 419) 9246 0203 62

whip hose - 10FT 3/8” NPT swivel (All CP chip hammers) 9246 0203 63

whip hose - 10FT - 3/8” NPT swivel & 5oz oiler (all CP chip hammers) 9246 0203 65

whip hose - 10FT - 7/8” - 24 swivel & 5oz oiler (TEX 317-419) 9246 0203 66

lubricator comp 3/4” NPT - 5oz 9246 0203 69



CP Airolene Plus tool oil .5L 8099 0202 41

CP Airolene Plus tool oil 1L 8099 0202 43

CP Airolene Plus tool oil 5L 8099 0202 49

CP Airolene Plus rockdrill oil 1L 8099 0201 02

CP Airolene Plus rockdrill oil 4L 8099 0201 03

inlet swivel 7/8” X 24 (CP 4123/CP 4125/CP 4132) 9246 0203 70

inlet swivel 3/8” NPT (CP 4130/CP 4131) 9246 0203 71

inlet swivel - 1/2” pipe - rivet busters 9246 0203 72

coupling - 1/2” universal hose end 9246 0204 35

coupling - 3/4” universal hose end 9246 0204 36

coupling - 1” universal hose end 9246 0204 37

coupling - 1/2” universal female 9246 0204 38

coupling - 3/4” universal female 9246 0204 39

coupling - 1” universal female 9246 0204 40

coupling - 1/2” universal male 9246 0204 41

coupling - 3/4” universal male 9246 0204 42

coupling - 1” universal male 9246 0204 43

hose clamp-1/2” 2-bolts 9246 0204 44

hose clamp-3/4” 2-bolts 9246 0204 45

hose clamp-1” 2-bolts 9246 0204 46

universal coupling gasket - 50/bag 9246 0204 82

safety clip 9246 0204 83

spring guard for 1/2” whip hose 9246 0204 84

whip check - hose-to-hose safety cable 9246 0204 85

whip check - hose-to-tool safety cable 9246 0204 86

26

Accessories

27

Portable Compressors

Chicago Pneumatic Portable Compressors

CPS 90

Free air delivery 88 cfm

Working pressure 100 psi

Max unloading pressure 125 psi

Discharge valves (2) x 3/4”

Fuel tank capacity 8.5 gallons

Engine Kubota (Tier 3)

Horsepower 24.4

Number of cylinders 3

Cooling system Water

Overall: Length 116 in

Height 47 in

Width 51.5 in

Weight 1,225 lbs

CPS 90

• Extremely reliable Kubota engine• Fully galvanized canopy• Recessed single point lifting eye• Torsion bar suspension• Heavy duty tires• Folding drawbar• Two 3/4” discharge valves• Removable side panels• 70 dB(a) @ 23 feet• Curbside fuel filling• Filter maintenance indicator

Reliability, easy maintenance and flexibility are the main characteristics of CP Portable Compressors. The range features proven designs with powerful engines from well-known, well-respected brands. With sound attenuated canopies and straightforward control panels, CP Portable Compressors are quiet and easy to use.

Danger: Compressed air should never be supplied as breathing air unless air is properly purified for breathing. Chicago Pneumatic assumes no responsibility or liability related to the purchaser’s/user’s breathing system.The information contained herein is general in nature and is not intended for specific construction, installation or application purposes.

CPS 90 PORTABLE COMPRESSORS

28


CPS 185 DD PORTABLE COMPRESSOR

CPS 185 DD





Fuel tank capacity 21 gallons

Engine Deutz (Interim Tier 4)

Horsepower 48


Cooling system Oil


Height 53 in

Width 55.5 in

Weight 1,980 lbs


The CPS 185 DD portable air compressor features a proven design with serviceability in mind. The wide opening one piece canopy opens fully for excellent service access. An efficient 48 hp Deutz engine is directly coupled to the compressor airend eliminating the need for high speed gears required by most competitors. A simple design and 500 hour maintenance interval provide for many years of reliable service.

Centralized Controls Curbside control panel with protective shutdown for high engine temperature, low oil pressure and high compressor temperature.

CPS 185 DD

• 500 hour service interval• Single point lifting eye• Torsion bar suspension• Heavy duty tires• Folding drawbar• Removable side panels• Fully galvanized enclosure• 48 HP Deutz engine• Curbside fuel filling• Highly efficient direct drive airend

The new CPS 185 PD portable air compressor from Chicago Pneumatic offers many features asked for by the rental industry. The corrosion resistant galvanneal steel canopy will ensure many years of service. A compact, lightweight design with recessed towing lights and a rear bumper provide greater maneuverability and added safety while towing. The CPS 185 PD features a highly efficient, direct-drive airend that provides 185 cfm of compressed air while using only a 49HP engine. The control panel and discharge valves are conveniently located at the rear of the compressor.

CPS 185 PD






Engine Perkins (Interim Tier 4)

Horsepower 49




Height 57 in

Width 60 in

Weight 2,375 lbs

29

CPS 185 PD PORTABLE COMPRESSOR

CPS 185 PD

• Toolbox• Recessed towing lights• Rear bumper• Electric fuel gauge• Low fuel shutdown• Direct drive airend• 49 HP Perkins engine• Galvanneal steel canopy• Torsion bar suspension• Single point lifting eye• Glow plug engine preheat• Wide opening one piece canopy• Protective shutdown system for

high compressor temperature, high engine temperature, low oil pressure, low fuel level

• Folding drawbar with adjustable jackstand and safety chains

Centralized Controls Control panel and discharge valves are conveniently located on the rear of the compressor. The CPS 185 PD control panel includes an hourmeter, discharge pressure gauge, electric fuel gauge, engine preheat actuator and rotary start switch. The control system also provides protective shutdowns for high engine temperature, low oil pressure, high compressor temperature and low fuel level.

CPS 375

• 500 hour service interval• Large tool storage box• Unloaded starting• Torsion bar suspension• Glow plug engine preheat• Recessed towing lights• Dual stage water separator• Fuel level gauge and hour meter• Low fuel shutdown• Single point lifting eye• Galvanneal sheet metal enclosure w/powder coat paint• Full length lockable doors• A-frame drawbar with adjustable pintle eye,

retractable swivel wheel and safety chains

CPS 375 PORTABLE COMPRESSOR

CPS 375





(1) x 11/2”


Engine Perkins (Tier 3)

Horsepower 111




Height 71 in

Width 72 in

Weight 3,860 lbs

The Chicago Pneumatic CPS 375 portable air compressor provides the strength and flexibility required for today’s demanding applications. The sturdy A-frame drawbar, mechanically controlled Perkins engine and 500 hour maintenance intervals assure many years of dependable service. Standard features include road lights, electric fuel gauge, low fuel shutdown and full length lockable doors. A built-in aftercooler, water separator, primary and secondary filter package is available as an option for applications where clean, dry compressed air is critical.

30



CPS 750





(1) x 11/2”


Engine Caterpillar (Tier-3)

Horsepower 200




Height 78 in

Width 78 in

Weight 6,450 lbs

CPS 750 PORTABLE COMPRESSORS

The Chicago Pneumatic CPS 750 portable air compressor features an extremely compact, lightweight, single-axle design. The smaller size 750 cfm compressor with mechanical surge brakes and road lights allows for easier towing and greater maneuverability. This compressor also features centralized fluid drains for ease of maintenance; compressor oil, engine oil and engine coolant all drain to a common point on the rear of the compressor. The CPS 750 uses a highly efficient airend design that only requires a 200 hp Caterpillar engine to produce 750 cfm of air. A built-in aftercooler, water separator, primary and secondary filter package is available as an option for applications where clean, dry compressed air is critical.

CPS 750

• 500 hour service interval• Single axle design• Mechanical surge brakes• Recessed towing lights• Built in thermostatic bypass valve• Low fuel shutdown• Single point lifting eye• Large tool storage box• Rear bumper• Torsion bar suspension• Three stage fuel filters w/ water separator• Automatic engine preheat• Galvanneal sheet metal enclosure

w/ powder coat paint• A-frame drawbar with adjustable pintle eye,

retractable swivel wheel and safety chains• Triple aluminum radiators designed for optimum

compressor efficiency• Centralized fluid drain point for compressor oil,

engine oil and coolant• Protective shutdowns for engine and compressor

31

32

1.5-13HP

Reciprocating Air Compressors

RCP-908H

RCP-2030

RCP-1330G

Features

• Start-Stop Pressure Switch Control • Fully Enclosed Belt Guard • Tank Drains and Discharge Valve

Features

• Engine Slowdown (Pilot Valve) • Engine Oil Protection• Fully Enclosed Belt Guard Tank Drains and Discharge Valve • ASME Tank and Safety Valve

Single Stage Electric Contractor SeriesPart Number HP Model Amps Electrics

V / Ph.cfm

100 psiTank gal.

L x W x Hinches

8090250831 1.5 RCP-1530 14 115 / 1 5.4 2 x 4 46 x 23 x 26

8090250849 2 RCP-2030 19 / 9.5 115 / 230 / 1 6.5 2 x 4 46 x 23 x 26

Two Stage Gasoline Drive

Part Number HP Model Engine cfm100 psi

Tank gal.

L x W x Hinches

8090250631 9 RCP-930G Robin 16.0 30H 45 x 19 x 38

8090250606 10 RCP-1030G Intek 16.0 30H 45 x 19 x 38

8090250607 11 RCP-1130G Honda 18.5 30H 45 x 19 x 45

8090250823 12.75 RCP-1230GK Kohler 18.5 30H 45 x 19 x 45

8090250608 12.75 RCP-1230G Kohler 25.3 30H 45 x 19 x 45

8090250609 13 RCP-1330G Honda 25.3 30H 45 x 19 x 45

Features

• 12 Volt Electric Start and Recoil Start• Start Key / Panel • Oil Monitor • Engine Slowdown (Pilot Valve)• Fully Enclosed Belt Guard • EZ Pull Tank Drain • ASME Tank and Safety Valves • 3/4” Tank Discharge Valve

Two Stage Gasoline Drive Contractor SeriesPart Number HP Model Engine Starter cfm

100 psiTank gal.

L x W x Hinches

8090250872 9 RCP-908R Robin Recoil 18.6 2 x 5 50 x 29 x 37

8090250880 9 RCP-908H Honda Recoil 18.6 2 x 5 50 x 29 x 37

8090250898 12.75 RCP-128-I Kohler Elec & Recoil 25.3 2 x 5 50 x 29 x 37

Single Stage Gasoline Drive Contractor SeriesPart Number HP Model Engine Starter cfm

100 psiTank gal.

L x W x Hinches

8090250856 5.5 RCP-5530 Honda Recoil 12.4 2 x 4 46 x 23 x 26

8090250864 6 RCP-6030 Robin Recoil 12.4 2 x 4 46 x 23 x 26

Aftermarket

CP engine oilsTo maintain the quality of your compressor, use the engine oil that is designed specifically for your compressor engine - GenOil. This genuine oil is a combination of supreme quality oil blended with special additives. The benefits of using GenOil are better corrosion protection and higher oxidation stability which results in longer oil service intervals and optimal engine performance.

CP coolantGenCool is a superior, high-quality coolant based on a new range of organic coolants. It reduces the operating temperature of the engine and has anti-freeze protection up to -40°C. The long-term corrosion protection allows for extended service intervals. GenCool will provide your engine with year-round protection.

CP compressor oilsGenOil is the only approved and tested oil that meets the quality specifications for your compressor. Our compressor oil has been thoroughly tested to give the optimum level of protection, lengthening the components’ life time and keeping your cost of ownership to an absolute minimum. GenOil keeps the heart of your machine operating at peak performance.

Service KitsThere is no better way to protect your investment than to use genuine parts. CP service packs include all required parts for scheduled maintenance, saving you time and money. With the convenient use of our service kits you will extend the life of your compressor, lower your maintenance costs and increase your profitability.

Genuine Parts

Filters

Air Filters

Lubricants

Coolants

ORIGINAL PART

Original Parts fit the best. Only they will guarantee the original performance of your machine.To ensure maximum working efficiency and a long lifetime every part must conform to specific technical standards. With the use of Original Parts you are certain about the quality, lifetime, utilized material and the impact on other components. All these aspects are important to make the right choice for spare parts. Therefore your best choice is an Original Part. Built to perform and designed to protect.

33

Single Stage Electric Contractor SeriesPart Number HP Model Amps Electrics

V / Ph.cfm

100 psiTank gal.

L x W x Hinches

8090250831 1.5 RCP-1530 14 115 / 1 5.4 2 x 4 46 x 23 x 26

8090250849 2 RCP-2030 19 / 9.5 115 / 230 / 1 6.5 2 x 4 46 x 23 x 26

Two Stage Gasoline Drive

Part Number HP Model Engine cfm100 psi

Tank gal.

L x W x Hinches

8090250631 9 RCP-930G Robin 16.0 30H 45 x 19 x 38

8090250606 10 RCP-1030G Intek 16.0 30H 45 x 19 x 38

8090250607 11 RCP-1130G Honda 18.5 30H 45 x 19 x 45

8090250823 12.75 RCP-1230GK Kohler 18.5 30H 45 x 19 x 45

8090250608 12.75 RCP-1230G Kohler 25.3 30H 45 x 19 x 45

8090250609 13 RCP-1330G Honda 25.3 30H 45 x 19 x 45

Red Hawk

Freedom of movement, zero set-up timeFrom the leading supplier of demolition tools comes the Red Hawk gas-powered breaker. Tough and well designed, the Red Hawk is ideal for small jobs or for working in remote locations.

With no compressors, hoses or cables to set up, gas-powered breakers are ideal for smaller jobs. An impressive range of tools make the Red Hawk extremely flexible and the 7/8” and 4 1/4” steels make for rapid penetration of concrete.

A multi-purpose tool With a wide range of tools, you can use the Red Hawk for everything from cut-ting and breaking to driving and compacting. Whether you need to just break a small patch of concrete, or drive a tent stake, you can get the job finished with a gasoline-powered machine in the same amount of time it takes to set up a compressor and hoses.

Use the rugged andversatile Red Hawk to:

• break concrete • cut asphalt • dig• drive posts and fences• drive rods and spikes• tamp and compact soil• tamp ballast/ties

Breaking concrete

Cutting asphalt

Tamping

Digging

34

Gas-Powered Breaker

Low emissions, vibrations and noise level Red Hawk is a modern tool that meets evolving regulations. Equipped with a catalytic converter and newly designed carburetor, the machine meets tough US EPA 1 emission regulations. In addition, a muffler has reduced the noise level from 114 dB to 107 dB, thereby fulfilling the European Noise Emission Directive.

Easy to start With a choke control, carburetor and user-friendly instructions, the Red Hawk is easy to start.

An optional guide roller makes it easier to pull downwards to start the machine when it is placed higher up. Order part number 9234 0009 38.

Easy to transport The Red Hawk weighs in at about

50 pounds. Each comes with its own carrying case which fits easily into

the trunk of your car.

Vibration-dampening handles

35

Engine

Type Power Cooling system Starter system Recommended fuel Oil type Oil mix Fuel capacity Fuel consumption Impact rate185 cc 1-cylinder, 2-stroke

1kW Forced air Recoilstarter

Unleaded Synthetic two-stroke oil

2% 1:50 0.31 US Gal

0.36 US Gal/hr 2600 BPM

Technical dataModel Part Number Weight

(lb)Length

(in)D

(in)Width over handles

(in)Tool shank (in)

Sound level (Acc. to ISO 3744)

Vibration level (Acc. to ISO 8662)

Red Hawk 8318 0900 00 50.5 27.3 11.0 23.0 7/8" - 4 1/4" 107 dB 4.7 m/s2

At Chicago Pneumatic, we maintain a comprehensive range of chisels so that you can select the right tool for the job. Chicago

Pneumatic chisels are among the hardest wearing on the market. A controlled heat treatment process imparts both strength and high wear resistance to deep surface layers while maintain-ing a tough shock resistant central core to resist breakage.The striking face is end-milled. This results in better contact between the piston and the tool, improved transfer of energy, as well as less vibration and wear on both hammer and chisel.

ToolsTool type Working length Tip width Weight Part number

Shank H 22x108 mm (H 7/8 x 4 1/4 in) mm (in.) mm (in.) kg (lb)

1 Tie tamper 390 (15 1/2) 90 (3 1/2) 3.0 (6.5) 3083 3237 00

Tie tamper 460 (18) 90 (3 1/2) 3.2 (7.0) 9245 2823 30

Tie tamper 550 (22) 90 (3 1/2) 3.9 (8.5) 9245 2822 40

2 Moil point 350 (14) 1.4 (3.1) 3083 3228 00

Moil point 480 (19) 2.0 (4.5) 3083 3229 00

3 Wide chisel 240 (9 1/2) 45 (1 3/4) 1.2 (2.7) 3083 3231 00

Wide chisel 340 (13 1/2) 45 (1 3/4) 1.4 (3.1) 3083 3230 00

Wide chisel 380 (15) 75 (3) 2.6 (5.7) 3083 3232 00

Wide chisel 450 (18) 45 (1 3/4) 2.0 (4.5) 3083 4071 00

4 Asphalt cutter 350 (14) 125 (5) 3.0 (6.5) 9245 2812 90

5 Digging chisel 280 (11) 75 (3) 2.7 (6.0) 3083 3233 00

6 Digging spade 330 (13) 120 (4 3/4) 3.6 (8.0) 3083 3234 00

7 Wedge set 29 mm 1.5 (3.3) 9245 2813 81

Wedge set 34 mm 2.1 (4.6) 9245 2813 51

8 Ground rod driver 195 (7 3/4) 42 (1 11/16) 1.2 (2.6) 3083 3241 00

9 Clay spade 350 (14) 125 (5) 3.4 (7.5) 3083 3235 00

10 Wedge chisel 380 (15) 35 (1 3/8) 2.8 (6.2) 3083 3236 00

11 Driver blank 195 (7 3/4) 55 (2 1/8) 2.5 (5.5) 9245 2822 80

12 Shank for pad 185 (7 1/4) 1.3 (2.9) 3083 3238 00

13 Tamping pad, round 175 (7) 7.5 (16.5) 3083 3252 10

14 Tamping pad, square 175 (7) 5.7 (12.5) 3083 3239 00

15 Tamper sq., compl. 190 (7 1/2) 175 (7) 7.0 (15.5) 3083 3240 00

16 Driver pad, round 100 (4) 2.5 (5.5) 9245 2817 90

17 Post hole driver 460 (18) Ø 40 Ø 1 1/2 4.2 (9.2) 9245 2822 31

18 Stake driver (2.5") 64 2 1/2 ID 5.0 11.0 9245 9800 50

19 Shank for 2.5" stake driver 228 9 2.1 4.6 9245 9912 41

2 Moil point

4 Asphalt cutter

1 Tie tamper

3 Wide chisel

6 Digging spade 7 Wedge set

8 Ground rod driver 9 Clay spade

10 Wedge chisel 11 Driver blank

12 Shank for pad 13 Tamping pad, round

14 Tamping pad, square 15 Tamper sq., compl.

17 Post hole driver

19 Shank for stake driver

16 Driver pad, round

18 Stake driver (2.5")Use only authorized parts. Any damage or malfunction caused by the use of unauthorized parts is not covered by Warranty or Product Liability.

AccessoriesDescription Part Number

20 Guide roller 9234 0009 38

21 Carrying harness 9238 2814 10

21 Carrying harness20 Guide roller

36

Redhawk Tools

37

Hand Held Hydraulic Tools

Absolutely. Chicago Pneumatic (CP) supplies a complete line-up – and you won’t believe how convenient, portable and versatile they are, particularly if you travel to a new site every day, do the job in hours and then move on. Take the power source, for instance. Instead of towing a heavy compressor, you have a compact, portable hydraulic power pack.

OK, but do these tools have the power I need? You will be pleasantly surprised. With hydraulic tools you get raw power from the power pack directly into the tool. They not only feel more powerful but they actually outperform other, comparable tools. Take our 16-inch saw. At full throttle, you have all the power of an 18 HP engine in your hand in a tool weighing only 23 pounds.

For building renovation, highway maintenance, utilities and all situations where portability and flexibility can save time and effort, hydraulic tools are the solution. Use them anywhere, independent of electric or pneumatic supply, in all weather conditions.

Bet they cost an arm and a leg!No. In fact, for smaller construction and rental companies, there are major cost advantages. For instance, for the price of one compressor/breaker combination, you can purchase two complete hydraulic power pack/breaker packages.

Hand Held Hydraulic Tools

Are you saying that hydraulic tools can make my job easier?

38

This power pack sure looks portable!

Power packs PAC P9 PAC P13 PAC P18 PAC D10Engine 9 HP, Honda gasoline 13 HP, Honda gasoline 18 HP, B&S Vanguard gasoline 10 HP, Lombardini dieselWeight (incl oil) lb 130 192 243 256Dimensions (LxWxH) in 23.0x20.7x26.8 27.7x23.6x29.3 28.3x27.6x29.3 27.7x23.6x29.3Oil flow gpm 5 5-8 5-10 5Maximum pressure psi 2200 2200 2200 2000Fuel capacity US gal 1.5 1.8 1.9 1HTMA Type I I / II I / II / RR IHose included NO NO NO NOPower on Demand (POD) YES YES NO NOOil control: engine oil YES YES NO NOElectric start NO NO YES YESPart number 1) 1807 0080 26 1807 0110 25 1807 0160 34 1807 0110 27

Exactly. Why tow a large compressor to the site if you don’t need to? The CP hydraulic power pack couldn’t be more convenient. For site-to-site transportation, two people can lift it into a truck. On-site, the CP power pack can easily be wheeled around by one person.

CP hydraulic power packs are available in gasoline, diesel or electrically driven versions, and provide portable power for a long list of applications in the 5-10 gpm/2000-2500 psi range.

How are they to operate?Couldn’t be simpler. The thermostatically controlled oil cooler gives fast warm-up and helps prevent the hydraulic oil from overheating. Correct working temperature is achieved within minutes – even during the winter. The variable flow on/off valve allows for simple tool changes and slow start up. A gauge shows when it’s time to change the filter.

What about fuel consumption?Many of the power packs are equipped with Power On Demand. This system automatically idles the engine when the tool is not being used and speeds it up when the tool is activated. It saves fuel and keeps noise to a minimum.

Power Pack

39

CP hydraulic breakers – a team of real hard-hitters

Pick hammer BRK 25 DShank size Hex in 7/8 x 3 1/4Weight lbs 28Length in 24Oil flow gpm 5Working pressure psi 1000-1300Return line pressure max psi 150Vibration level (ISO 8662-5) m/s2 10.1Impact rate (5 gpm) blows/min 2400HTMA class IPart number 1801 1746 12

Looking for flexibility – or just raw power?Either way, you’ve found it. CP hydraulic breakers range from flexible, lightweight models up to super heavy duty models hitting at 103 foot pounds and delivering an average of 1,276 blows per minute. Whatever the job, large or small, light or heavy, CP has the right tool in its breaker line-up.

Get more done!The slim design of CP hydraulic breakers gives a good line of sight to the working tool point which boosts your produc-tivity. The tools are well balanced, with no external side bolts and protruding machine parts that can come into contact with the operator’s body.

Quick couplings Hoses are fitted with flat face HTMA quick release couplings for fast and easy connections in all work situations. The couplings are designed to help keep hydraulic systems clean on work sites where there are large amounts of dust and dirt.

BRK 25 D A powerful horizontal pick hammerGet a grip on horizontal tasks! With an impact energy of 18 foot pounds at 2,400 blows/min., the BRK 25 D D-handle hammer is the powerful choice for horizontal work in renovation, demolition and structural alteration. The detachable front handle, available as an optional extra, pivots 360° for optimal positioning.

Hammers, Breakers

40

Breakers BRK 40 BRK 40 VR BRK 55 BRK 55 VR BRK 70 BRK 70 VR BRK 95 BRK 95 VR

Weight lbs 41 42 46 47 56 57 71 73

Length in 25 25 27 27 30 30 30 30

Oil flow gpm 5 5 8 1) 8 1) 8 1) 8 1) 8 2) 8 2)

Working pressure psi 1300-1600 1300-1600 1500-1800 1500-1800 1500-1800 1500-1800 1500-1800 1500-1800

Return line pressure max psi 150 150 215 215 215 215 215 215

Vibration level (ISO 8662-5) 3) m/s2 8.3 3.5 11.4 3.3 11.4 3.4 14.2 6.0

Impact rate (5 gpm) blows/min 1600 1600 1450 1450 1270 1270 - -

Impact rate (8 gpm) blows/min - - 2160 2160 1860 1860 1150 1150

Impact rate (10 gpm) blows/min - - - - - - 1500 1500

HTMA class I I II (I) 1) II (I) 1) II (I) 1) II (I) 1) II (RR) 2) II (RR) 2)

Part number 25x108 (1 x 4¼) 1801 3446 11 1801 3446 10 1801 3546 05 1801 3546 04 - - - -

Part number 28x152 (1¼ x 6) - - 1801 3546 83 - 1801 3646 84 1801 3746 75

Part number 28x160 (1⅛ x 6¼) 1801 3446 58 - 1801 3546 63 - 1801 3646 70 1801 3646 69 - -

Part number 32x152 (1¼ x 6) 1801 3446 60 1801 3446 59 1801 3546 65 1801 3546 64 1801 3646 73 1801 3646 72 1801 3746 85 1801 3746 74

Part number 32x160 (1¼ x 6¼) 1801 3446 62 1801 3446 61 1801 3546 68 1801 3546 67 1801 3646 07 1801 3646 06 1801 3746 09 1801 3746 08

1) Can be adjusted to 5 gpm 2) Can be adjusted to 10.5 gpm 3) BRK 40, BRK 55 and BRK 70 measured at 5 gpm/min, BRK 95 measured at 8 gpm/min

BRK 40 Lightweight , multi-purpose breakers The perfect choice for indoor and outdoor renovation and demo lition jobs, BRK 40 breakers have an impact energy of 48 foot pounds at 1,600 blows/min. Brickwork, frozen soil, asphalt, and concrete are no match for these tough, lightweight breakers. Frequently chosen by contractors and rentals, BRK 40 breakers are also effective for tamping and compaction and are used by railroad companies for tie tamping applications.

BRK 55Medium weight, multi-purpose breakers A favorite with rental companies, BRK 55 breakers are the ideal choice for road building and maintenance applications. Whether it’s asphalt, brickwork, frozen soil, or concrete, the BRK 55 gives you reliable performance. Can be used with both 8 gpm and 5 gpm power packs.

BRK 70Heavy-duty, multi-purpose breakers Get the job done, fast! BRK 70 breakers are idealfor heavier jobs in tough materials such as aphalt,frozen soil, and reinforced concrete. They work at a standard flow rate of 8 gpm and at 5 gpm with a simple adjustment.

BRK 95Super heavy-duty breakers Handheld breakers don’t get much more powerful than this. With an impact energy of 103 foot pounds and an impact rate of 1,275 blows/min., in some situations, the BRK 95 can even replace small excavators with breaker attachments. Ideal for breaking heavy asphalt, reinforced concrete and foundations, these powerful machines are the rugged choice for utility construction, street maintenance, repair of water and gas lines and general construction jobs.

Hammers, Breakers

41

CP hydraulic saws and drills – perfect working partners

Cut-off saws SAW 14 SAW 16Weight lb 21.6 23.4Oil flow gpm 5-8 5-10Max oil pressure psi 2500 2500Revolutions rpm 2500-4000 2000-4000Circumferential speed ft/s 151-246 138-279Blade size in 14 16Arbor hole diameter in 1 1Cutting depth when used handheld in 5.2 6.3Cutting depth when mounted in cart in 3.9 4.9HTMA Type I / II I / II / RRPart number 1809 0140 03 1809 0166 13

Core drills COR 5 COR 15Weight lb 18 18Oil flow gpm 5 - 8 5 - 8Length without drill in 16 16Working pressure psi 1160 - 2500 1160 - 2500Revolutions rpm 600 - 900 1500 - 2250Drill diameter in 2 - 8 0.5 - 3Thread female (drive) 1) ½" BSP ½" BSPHTMA Type I / II I / IIPart number 1806 1014 54 1806 1014 55

1) 1/2” BSP male x 1 1⁄4 UNC male drive adaptor included for use of larger diameter core bits.

CP cut-off sawsYou name it, CP cut-off saws will cut itThey may be light and compact, but don’t be fooled. A CP hydraulic cut-off saw with the right blade will cut through concrete, asphalt and steel. With our 16-inch saw at full throttle, you have the raw power of a gasoline powered engine in your hand.

The open cutting face makes the CP cut-off saw easy to use, even under the most demanding conditions. The simple, direct drive configuration reduces maintenance, especially in comparison with belt-driven saws.

A water kit is available to provide a supply of cooling water where needed.

CP core drillsIdeal for working in confined areas Take a CP hydraulic core drill with you when installing drainage, sewer and water pipes, or cable and ventilation ducts where large, deep holes are needed. CP core drills are well suited for drilling concrete, masonry and asphalt materials. They can be operated freehand or mounted in a drill stand.

Hydraulic control of the drill torque helps to reduce kickback when drill bits jam. So you’re in control, even when drilling holes of 8 inches in diameter and above. Due to the compact design of the CP core drill, you can easily drill holes of up to 8 inches freehand.

Water KitDiamond blades and core bits need a constant supply of water to cool, flush away slurry and suppress dust. On re-mote sites where there is no water supply, we recommend the CP water kit, a small pressurized water container.Item number 3371 8090 02.

Cut off saws, core drills

42

It takes more than stones and debris to stop a CP submersible pump!

Water pumps WAP 2 WAP 3Weight lb 22.6 28Dimensions HxW in 10.5x8.5 14.2x11.8Oil flow gpm 4-6 7-10Working pressure psi 1400 2000Max working pressure psi 2300 2500Pump head max ft 82 105Pump flow max gal/min 222 507Discharge in 2" BSP 3" BSPSolid handling up to in 3/8" 2½"HTMA Type I IIPart number 1806 1014 41 1806 1014 42

CP submersible pumpsThese tools are really toughCP hydraulic submersibles are a range of rugged pumps for continuous pumping of water on building sites, in flooded excavations and cellars, and similar situations. Performance is impressive in relation to size and weight. The 2 inch pump handles dirty water containing small stones and debris up to 3/8 inch. The 3 inch CP submersible trash pump can handle rocks of up to 2 1/2 inches in diameter!

Cooled and lubricated by the hydraulic oil, they can be left to run dry without damage.

Hoses ft 23 39Flat face quick couplings dimension ½" ½"HTMA class I / II / RR I / II / RRPart number 3371 8010 87 3371 8010 89

Water pumps, OFD and hoses

Oil flow divider OFD 5 OFD 8Max oil flow rate gpm 15.8 31.0Regulated oil flow rate gpm 5.3 - 6.6 6.6 - 8HTMA Type I IIPart number 1801 1633 19 1801 1643 18

Accessories – for your hydraulic toolsOil flow divider Reduces flow and pressure, allowing you to run tools from hydraulic-powered carriers. Use an extension hose to connect the oil flow divider to the tool.

Extension hoses Add one or two 23 ft. extension hoses and you can use up to 69 ft. of hose without significant drop in pressure. The hoses are fitted with flat-face, quick release couplings.

43

Classification of toolsFlow 5 gpm 8 gpm 10 gpm

HTMA I II RR

EHTMA C D E

Working tools

Working Tools

Chicago Pneumatic Construction Equipment offers a full range of working tools for its hand held equipment.

Flat to flat (North America) Point to Flat (North America)

7/8 x 3 1/4 in 1 x 4 1/4 in 1 1/8 x 6 in 1 1/4 x 6 in

W (in) L (in) Part no. W (in) L (in) Part no. W (in) L (in) Part no. W (in) L (in) Part no.

Moil point 14 3083 4050 00 15 3083 4030 00 14 3083 3267 00 14 3083 3285 00

18 3083 4050 10 18 3083 4030 10 18 3083 4015 10 18 3083 4000 10

24 3083 4050 20 24 3083 4030 20 24 3083 4015 20 24 3083 4000 20

36 3083 4050 30 36 3083 4030 30 36 3083 4015 30 36 3083 4000 30

Narrow chisel 1 14 3083 3303 00 1 1/8 15 3083 3309 00 1 1/4 14 3083 3268 00 1 3/8 14 3083 3286 00

1 18 3083 4051 10 1 1/8 18 3083 4031 10 1 1/4 18 3083 4016 10 1 3/8 18 3083 4001 10

1 24 3083 3304 00 1 1/8 24 3083 4031 20 1 1/4 24 3083 4016 20 1 3/8 24 3083 4001 20

1 36 3083 4051 30 1 1/8 36 3083 4031 30 1 1/4 36 3083 4016 30 1 3/8 36 3083 4001 30

Wide chisel 3 14 3083 3305 00 3 15 3083 3310 00 3 15 3083 3289 00 3 15 3083 3295 00

3 18 3083 4052 10 3 18 3083 4032 00 3 18 3083 4017 00 3 18 3083 4002 00

3 24 3083 4052 20 3 24 3083 4032 10 3 24 3083 4017 10 3 24 3073 4002 10

Wedge chisel 1 3/8 15 3083 4057 00 2 15 3083 3313 00 2 16 3083 3294 00 2 16 3083 3300 00

Digging chisel 3 14 3083 3306 00 3 15 3083 3311 00 3 15 3083 3291 00 3 15 3083 3297 00

Digging spade 4 3/4 13 3083 3307 00 4 3/4 13 3083 3312 00 5 13 3083 3292 00 5 13 3083 3298 00

Asphalt cutter 5 12 3083 4053 00 5 13 3083 4033 00 5 13 3083 3290 00 5 13 3083 3296 00

Clay spade 5 17 3083 3308 00 5 16 3083 4035 00 5 1/2 15 3083 3293 00 5 1/2 15 3083 3299 00

Shaft for pad 8 3083 4058 00 11 3083 4037 00 9 3083 3269 00 9 3083 3287 00

Tamping pad, round 7 3083 3252 10 7 3083 3252 10 7 3083 3301 00 7 3083 3301 00

Tamping pad, square 7 3083 3239 00 7 3083 3239 00 6 3083 3302 00 6 3083 3302 00

Tamping pad, square 8 3083 3197 00 8 3083 3197 00

Driver pad, round 4 9245 2817 90 4 9245 2817 90

44

RX Hydraulic Breakers

Traditional breaker with 4 side bolts and nutsThe decades old traditional hydraulic breaker technology is complex with many parts.

RX hydraulic breakers (RX2 – RX22)With the exception of the RX11, these RX breakers have fewer components. Only two moving parts and no high pressure accumulator mean less chance of failure. No side bolts make them easier to service, maintain and repair since a multi torque wrench isn’t needed.

RX hydraulic breakers (RX25 – RX53)The RX25-RX53 models feature a cutting-edge side bolt system that uses head bolts and insert threads to distribute the thread strain equally.

RX Hydraulic Breakers – RX means R-eliable to the X-treme

Rugged and hard-hittingDon’t be fooled by their attractive, streamlined designed. RX hydraulic breakers are rugged, reliable and built to last. They have all the power you need to get the job done…and more. Attach the matching RX breaker to the carrier of your choice and you can power your way through a job in no time.

Decrease downtime, increase productivityThe innovative design of the RX line of breakers helps decrease downtime and increase productivity. The small-to-medium sized RX models have fewer components. Only two moving parts and no side bolts make them easier to service, maintain and repair. The larger models feature a power control valve to increase productivity. You can set the breaker characteristics according to the application for higher productivity. The larger models also feature a cutting-edge side bolt system that uses head bolts and insert threads to distribute the thread strain equally.

Less noise means less trouble with the neighborhood on the job siteThanks to the RX recoil absorbing concept and the polyurethane insulated breaker box system, RX breakers are among the quietest you can buy and in line with outdoor equipment directive 2000/14/EU.

45

Value-for-money features

Power booster – for maximum performanceThe power booster feature on RX breakers enables you to get higher breaking performance without increasing the hydraulic input in tougher breaking applications. While the impact energy remains constant, the breaker increases the blow frequency, which results in increased percussive performance.

Power Stop function – to protect your investmentThe power stop function reduces blank firing. That protects the breaker and carrier and increases the working life of the components.

Power control valve – to increase productivityRX breakers (from RX25 upwards) are equipped with a power control valve. This feature enables the operator to set the breaker characteristics according to the application – for higher productivity.

High impact, low noiseRX breakers comply with current and future regulations stipulated in the Noise Emission of Outdoor Equipment Directive 2000/14/EC.

No side bolts (RX2 – RX22)The lack of side bolts on the RX2 – RX22, excluding the RX11, makes these breakers more reliable and easier to service and maintain. Opening a breaker for resealing can be done with ordinary hand tools.

Cutting edge side bolts system (RX25 – RX53)The innovative side bolt system uses head bolts and insert threads to distribute the thread strain equally.

Dust wiperThe optional dust wiper, available on the RX14 upwards, helps increase the lifetime of components that can wear. Simple and reliable -- it keeps abrasive dust out and grease in.

CP-Lube – automatic lubricationBreaker models from the RX14 upwards can be equipped with optional automatic lubrication. CP-Lube ensures optimal lubrication of the wear bushings and the working tool and thus avoids unnecessary downtime.

Ventilation port

Highly efficient internal control valve

Double tool retainer bars(RX14 – RX53)

Dust wiper

CP-Lube for optimum lubrication

Hybrid technology (gas/oil)

High performance-to-weight ratio

Smart design with few components

Effective noise and vibration damping

Power booster

Power stop function

Power control valve

4646

Innovative technology; reliable service and support

A respected name for more than 100 yearsSince 1901 the Chicago Pneumatic name has represented high-performance tools and equipment designed for an extensive range of applications. Today, Chicago Pneumatic has a global reach, with local customer centers around the world.

Extensive investments in R&DThe innovative technology, unique design and value-for-money features of the RX hydraulic breaker line are the direct result of our extensive investments in R&D.

Worldwide customer supportBuying an RX breaker is just the beginning. Chicago Pneumatic distributors offer reliable service and support. Genuine spare parts for your RX breaker are available worldwide, with short delivery times.


4747

Thirteen breakers at your service

Model Service weight Carrier weight class Operating pressure Oil flow rate Blow frequency

Working tool diameter

Sound power level

Part no.

kg lb 1) t lb 2) bar PSI l/min gpm bpm mm in dB(A)

RX2 117 258 1,3-3,0 2,900-6,600 110-130 1,600-1,890 15-35 4-9 560-1700 42 1.65 109 4)/81 5) 8460 0500 38

RX3 166 366 2,1-4,5 4,600-9,900 110-140 1,600-2,030 30-50 8-13 670-1450 52 2.04 111 4)/83 5) 8460 0500 39

RX4 233 514 2,9-6,0 6,400-13,200 110-140 1,600-2,030 35-60 9-16 520-1150 62 2.44 113 4)/85 5) 8460 0500 40

RX6 284 626 4,2-9,0 9,300-19,800 110-140 1,600-2,030 45-75 12-20 530-1150 70 2.75 114 4)/86 5) 8460 0500 41

RX8 380 838 5,2-12,0 11,500-26,500 120-150 1,740-2,180 60-90 16-24 530-1050 80 3.14 115 4)/87 5) 8460 0500 42

RX11 550 1,210 9-15 19,800-33,100 120-150 1,740-2,180 70-100 18-26 590-1100 80 3.14 116 4) 3363 1095 21

RX14 800 1,760 10-17 22,000-37,500 150-170 2,180-2,470 100-120 26-32 650-850 100 3.93 3363 1049 61

RX18 1200 2,650 15-24 33,100-52,900 150-170 2,180-2,470 120-140 32-37 550-720 120 4.72 3363 1052 39

RX22 1500 3,310 17-28 37,500-61,700 150-170 2,180-2,470 140-160 37-42 520-680 135 5.31 3363 1051 01

RX25 1800 3,970 20-33 44,100-72,800 150-170 2,180-2,470 130-180 34-48 400-680 (460-800) 3)

140 5.51 3363 1056 01

RX29 2200 4,850 25-40 55,100-88,200 150-170 2,180-2,470 150-200 40-53 375-600 (400-800) 3)

150 5.90 3363 1058 93

RX45 3000 6,610 29-46 63,900-101,400 160-180 2,320-2,610 210-260 55-69 380-580(400-800)3)

165 6.49 121 4)/91 5) 3363 1053 59

RX53 4200 9,260 40-70 88,200-154,300 160-180 2,320-2,610 250-320 66-85 350-560(400-800)3)

180 7.08 3363 1097 39

RX hydraulic breakers – features at a glance• Hybrid technology (gas/oil)• Innovative design with less components• Effective noise and vibration damping • Highly efficient internal control valve• Power booster• Power stop function• Power control valve (RX 25-53)• Ventilation port*• Dual retainer bars*

Optional extras • CP-lube for optimum grease distribution*• Dust wiper*

* From RX14 upwards

1) Breaker and breaker box with standard adapter plus working tool.2) Weights apply to standard carriers only. Any variances must be approved by Chicago Pneumatic and/or the carrier manufacturer prior to attachment.3) Power Control: The blow frequency and impact energy can be adjusted to better meet the application requirements.4) Sound power level guaranteed.5) Sound pressure level (r=10m). Important: EN ISO 3744 in accordance with directive 2000/14/EC. Full details of measurement are available in the Safety and Operating Instruction of the product.

48

Original parts make your breaker even more effective


Model Tool type Working length Total length Part no.

RX2

Moil point (conical) 265 mm 10,43 in 425 mm 16,73 in 4211 1050 01

Chisel (cross) 265 mm 10,43 in 425 mm 16,73 in 4211 1050 02

Blunt tool 265 mm 10,43 in 425 mm 16,73 in 4211 1050 03

RX3




RX4




RX6




RX8




RX11




RX14




RX18




RX22




RX25




RX29




RX45




RX53




Working toolsPoor quality tools can prove to be expensive. Pieces of low grade metal can shear off, enter the hydraulic system and cause serious damage to the breaker and carrier.

Chicago Pneumatic tools are manufactured to the highest quality standards in a fully controlled process. All tools are made from a nickel-chrome alloy that has been optimized for breaking applications. Each tool is precision formed and temper hardened for greater wear resistance.

Description Size Part no.

Chisel paste cartridge (for CP-Lube) 30 x 500 g 3363 0949 10

Chisel paste

Moil point

Chisel

Blunt tool

Asphalt cutter

Wide chisel

49

Carrier classes

ton

(lb)

1 4 7 10 13 16 19 22 25 28 31 34 37 40 43 46 49 52 55 58 61 64 67 70

(2,2

00)

(8,8

00)

(15,

400)

(22,

000)

(28,

600)

(35,

300)

(41,

900)

(48,

500)

(55,

100)

(61,

700)

(68,

300)

(75,

000)

(81,

500)

(88,

200)

(94,

300)

(101

,400

)(1

08,0

00)

(114

,600

)(1

21,2

00)

(127

,800

)(1

34,5

00)

(141

,000

)(1

47,7

00)

(154

,300

)

200

400

550

750

1,000

1,200

2,000

2,500

3,500

4,500

5,000

7,500

10,000

RX2200

ft/lb class

RX3400

ft/lb class

RX4550

ft/lb class

RX6750

ft/lb class

RX81,000

ft/lb class

RX111,200

ft/lb class-

RX142,000

ft/lb class

RX182,500

ft/lb class-

RX223,500

ft/lb class

RX254,500

ft/lb class

RX295,000

ft/lb class

RX457,500

ft/lb class

RX5310,000

ft/lb class

Generators

50

CPG 25- CPG 120

Model CPG 25 CPG 45 CPG 70 CPG 90 CPG 120

Rated Standby Power 22kW/28kVA 39 kW / 50 kVA 67 kW / 84 kVA 80 kW / 100 kVA 106 kW / 133 kVA

Rated Prime Power 20 kW / 25 kVA 35 kW / 45 kVA 56 kW / 70 kVA 72 kW / 90 kVA 95 kW / 120 kVA

Voltage Selections - 3Ø 208 / 240 / 480 208 / 240 / 480 208 / 240 / 480 208 / 240 / 480 208 / 240 / 480

Voltage Selections - 1Ø 120 / 240 120 / 240 120 / 240 120 / 240 120 / 240

Amperage Capacity @ 120 volts 1Ø 2 x 72 amps 2 x 116 amps TBD 2 x 250 amps 2 x 333 amps

Amperage Capacity @ 240 volts 1Ø 72 amps 116 amps TBD 250 amps 333 amps




Sound Pressure Level @ 23 feet @ 75% load 65 dB(A) 68 dB(A) 67 dB(A) 67 dB(A) 67 dB(A)

Fuel Tank Capacity 30 gal. 70 gal. 160 gal. 160 gal. 160 gal.

Fuel Consumption At 75% Load 1.04 gl/hr 1.9 gl/hr TBD 4.9 gl/hr 5.9 gl/hr

Fuel Autonomy At 75% Load 29 hr 36 hr TBD 32.6 hr 27.1 hr

Engine Kubota Kubota John Deere John Deere John Deere

Model Kubota2403 V3600T 4045HF285 4045HF285 4045HF285

Rated Speed 1800 rpm 1800 rpm 1800 rpm 1800 rpm 1800 rpm

Emission Compliance EPA Interim Tier 4 EPA Interim Tier 4 EPA Tier III EPA Tier III EPA Tier III

Rated Output 29.6 HP @ 1800 rpm 49 HP @ 1800 rpm 99 HP @ 1800 rpm 126 HP @ 1800 rpm 158 HP @ 1800 rpm

Coolant Water / Glycol Water / Glycol Water / Glycol Water / Glycol Water / Glycol

Cylinders 4 4 4 4 4

Displacement 2.4 L 3.6 L 4.5 L 4.5 L 4.5 L

Engine Control Electronic Mechanical Electronic Electronic Electronic

Alternator Leroy Somer Stamford Stamford Stamford Stamford

Model LSA40M5 BCI184-H TBD UCI 224 G1 UCI 274 C1

Degree of Protection / Insulation Class IP23 / H IP23 / H IP23 / H IP23 / H IP23 / H

Dimensions Skid (L x W x H) 70 x 33.5 x 46.4 in 82.7 x 37.5 x 53 in 112 x 44 x 67 in 112 x 44 x 67 in 112 x 44 x 67 in

Weight - Skid Wet 1,868 lbs 2,410 lbs 5,310 lbs 5,310 lbs 5,360 lbs

Dimensions w/Trailer (L x W x H) 110 x 59 x 57 in 136.2 x 62.6 x 80.1 in 176 x 78 x 80 in 176 x 78 x 80 in 176 x 78 x 80 in

Weight - w/Trailer Wet 2,121 lbs 3,162 lbs 6,560 lbs 6,560 lbs 6,610 lbs

Convenience Receptacles

20 amp - 125 volt GFCI duplex 2 2 2 2 2

50 amp - 125 / 250 volt twist lock 2 2 2 2 2

Reliability, versatility and rugged design are the main characteristics of CPG Generators. The range features proven designs with powerful engines from well-known, well-respected brands. With Zincor steel coated canopies and 500 hour service intervals. Chicago Pneumatic generators can power a wide variety of critical applications even in the most demanding weather conditions.

Generators

51

Standard Features

• Multi-Voltage Selector Switch • Remote Start / Stop • Digital Control System • 110% Fluid Containment • Electronic Governor

Optional Features

• Skid-Mount• Battery Charger• Ball Coupling• Spare Tire• Tool Box• External Fuel Connections• Coolant Heater

Health, Safety and Environment

Chicago Pneumatic’s stringent manufacturing standards follow ISO 9001 quality assurance regulations. All components are produced and tested to exacting standards for optimum performance in the most demanding conditions.

CPG 45The CPG 45 portable generator from Chicago Pneumatic provides quieter operation, reduced emissions, and loweracquisition and operating costs. Applying insights gained from industrial customers, rental companies, public utilities, and otherend users, Chicago Pnuematic engineers designed the CPG 45 with the most desirable features and capabilities: Standard Features

• Multi-Voltage Selector Switch • Remote Start / Stop • Digital Control System • 110% Fluid Containment

Optional Features

• Skid-Mount• Battery Charger• Electronic Governor • Coolant Heater • Ball Coupling• Spare Tire• Rear Stabilizer Jacks• Tool Box• External Fuel Connections

• Diesel power from the reliable Kubota engine• Electrical power from Stamford BCI series alternator• Selectable 3-phase and 1-phase voltages• 24 hour run-time fuel capacity inside the base frame• 14 gauge galvanneal steel canopy for high durability• Spillage free frame for environmental protection• 120V single phase on the duplex in any voltage condition

CPG 120 (60 Hz)

Model CPG 25 CPG 45 CPG 70 CPG 90 CPG 120

Rated Standby Power 22kW/28kVA 39 kW / 50 kVA 67 kW / 84 kVA 80 kW / 100 kVA 106 kW / 133 kVA

Rated Prime Power 20 kW / 25 kVA 35 kW / 45 kVA 56 kW / 70 kVA 72 kW / 90 kVA 95 kW / 120 kVA

Voltage Selections - 3Ø 208 / 240 / 480 208 / 240 / 480 208 / 240 / 480 208 / 240 / 480 208 / 240 / 480

Voltage Selections - 1Ø 120 / 240 120 / 240 120 / 240 120 / 240 120 / 240

Amperage Capacity @ 120 volts 1Ø 2 x 72 amps 2 x 116 amps TBD 2 x 250 amps 2 x 333 amps





Sound Pressure Level @ 23 feet @ 75% load 65 dB(A) 68 dB(A) 67 dB(A) 67 dB(A) 67 dB(A)

Fuel Tank Capacity 30 gal. 70 gal. 160 gal. 160 gal. 160 gal.

Fuel Consumption At 75% Load 1.04 gl/hr 1.9 gl/hr TBD 4.9 gl/hr 5.9 gl/hr

Fuel Autonomy At 75% Load 29 hr 36 hr TBD 32.6 hr 27.1 hr

Engine Kubota Kubota John Deere John Deere John Deere

Model Kubota2403 V3600T 4045HF285 4045HF285 4045HF285

Rated Speed 1800 rpm 1800 rpm 1800 rpm 1800 rpm 1800 rpm

Emission Compliance EPA Interim Tier 4 EPA Interim Tier 4 EPA Tier III EPA Tier III EPA Tier III

Rated Output 29.6 HP @ 1800 rpm 49 HP @ 1800 rpm 99 HP @ 1800 rpm 126 HP @ 1800 rpm 158 HP @ 1800 rpm

Coolant Water / Glycol Water / Glycol Water / Glycol Water / Glycol Water / Glycol

Cylinders 4 4 4 4 4

Displacement 2.4 L 3.6 L 4.5 L 4.5 L 4.5 L

Engine Control Electronic Mechanical Electronic Electronic Electronic

Alternator Leroy Somer Stamford Stamford Stamford Stamford

Model LSA40M5 BCI184-H TBD UCI 224 G1 UCI 274 C1

Degree of Protection / Insulation Class IP23 / H IP23 / H IP23 / H IP23 / H IP23 / H

Dimensions Skid (L x W x H) 70 x 33.5 x 46.4 in 82.7 x 37.5 x 53 in 112 x 44 x 67 in 112 x 44 x 67 in 112 x 44 x 67 in

Weight - Skid Wet 1,868 lbs 2,410 lbs 5,310 lbs 5,310 lbs 5,360 lbs

Dimensions w/Trailer (L x W x H) 110 x 59 x 57 in 136.2 x 62.6 x 80.1 in 176 x 78 x 80 in 176 x 78 x 80 in 176 x 78 x 80 in

Weight - w/Trailer Wet 2,121 lbs 3,162 lbs 6,560 lbs 6,560 lbs 6,610 lbs

Convenience Receptacles

20 amp - 125 volt GFCI duplex 2 2 2 2 2

50 amp - 125 / 250 volt twist lock 2 2 2 2 2

More than 100 years of experienceChicago Pneumatic Tool Company has been designing, manufacturing and selling pneumatic tools since 1901. Today we offer a wide range of products including pneumatic and hydraulic breakers, clay diggers, picks and busters, scabblers, rock drills, rotary and chipping hammers, sump and sludge pumps, and a whole lot more. Having started up in the city that shares our name, today Chicago Pneumatic is a global company, with sales organizations around the world.

www.cp.com

Chicago Pneumatic Construction Equipment 3700 East 68th Avenue Commerce City, CO 80022 USA Tel: (800) 760-4049 Fax: (303) 288-8828

© 2

011

Atla

s Cop

co C

onst

ruct

ion

Min

ing

Tech

niqu

e U

SA L

LC.

9245

999

8 12

c

2/11

5,

000

www.cp.com

Over 100 years of experienceSince 1901 the name Chicago Pneumatic has stood for innovative, high-performance power tools. Today a wide range of pneumatic and hydraulic construction tools, including breakers, clay diggers, picks and busters, scabblers, rock drills, rotary and chipping hammers, sump and sludge pumps, and a whole lot more, are available through a worldwide sales organization.

For more detailed information, please contact:

3392

519

5 93

C

opyr

ight

200

8, C

hica

go P

neum

atic

Con

stru

ctio

n To

ols

Sub

ject

to te

chni

cal m

odifi

catio

ns.

2500

12/

08

a

Flat to flat (North America) Point to Flat (North America)7/8 x 3 1/4 in 1 x 4 1/4 in 1 1/8 x 6 in 1 1/4 x 6 in

W (in) L (in) Part no. W (in) L (in) Part no. W (in) L (in) Part no. W (in) L (in) Part no.Moil point 14 3083 4050 00 15 3083 4030 00 14 3083 3267 00 14 3083 3285 00

18 3083 4050 10 18 3083 4030 10 18 3083 4015 10 18 3083 4000 1024 3083 4050 20 24 3083 4030 20 24 3083 4015 20 24 3083 4000 2036 3083 4050 30 36 3083 4030 30 36 3083 4015 30 36 3083 4000 30

Narrow chisel 1 14 3083 3303 00 1 1/8 15 3083 3309 00 1 1/4 14 3083 3268 00 1 3/8 14 3083 3286 001 18 3083 4051 10 1 1/8 18 3083 4031 10 1 1/4 18 3083 4016 10 1 3/8 18 3083 4001 101 24 3083 3304 00 1 1/8 24 3083 4031 20 1 1/4 24 3083 4016 20 1 3/8 24 3083 4001 201 36 3083 4051 30 1 1/8 36 3083 4031 30 1 1/4 36 3083 4016 30 1 3/8 36 3083 4001 30

Wide chisel 3 14 3083 3305 00 3 15 3083 3310 00 3 15 3083 3289 00 3 15 3083 3295 003 18 3083 4052 10 3 18 3083 4032 00 3 18 3083 4017 00 3 18 3083 4002 003 24 3083 4052 20 3 24 3083 4032 10 3 24 3083 4017 10 3 24 3073 4002 10

Wedge chisel 1 3/8 15 3083 4057 00 2 15 3083 3313 00 2 16 3083 3294 00 2 16 3083 3300 00Digging chisel 3 14 3083 3306 00 3 15 3083 3311 00 3 15 3083 3291 00 3 15 3083 3297 00Digging spade 4 3/4 13 3083 3307 00 4 3/4 13 3083 3312 00 5 13 3083 3292 00 5 13 3083 3298 00Asphalt cutter 5 12 3083 4053 00 5 13 3083 4033 00 5 13 3083 3290 00 5 13 3083 3296 00Clay spade 5 17 3083 3308 00 5 16 3083 4035 00 5 1/2 15 3083 3293 00 5 1/2 15 3083 3299 00Shaft for pad 8 3083 4058 00 11 3083 4037 00 9 3083 3269 00 9 3083 3287 00Tamping pad, round 7 3083 3252 10 7 3083 3252 10 7 3083 3301 00 7 3083 3301 00Tamping pad, square 7 3083 3239 00 7 3083 3239 00 6 3083 3302 00 6 3083 3302 00Tamping pad, square 8 3083 3197 00 8 3083 3197 00Driver pad, round 4 9245 2817 90 4 9245 2817 90

Working tools

Classification of toolsFlow 5 gpm 8 gpm 10 gpmHTMA I II RREHTMA C D E

products. construction equipment - toolsrenewed.comtoolsrenewed.com/new tools/cp/co-2011...

Documents