Introduction
The Chicago Pneumatic Brand offers a complete line of Construction Equipment designed to efficiently handle a broad range of applications.
Each Chicago Pneumatic (CP) tool is easy to use, comfortable to hold, and operates at top performance over an unusually long life. CP Compressors are reliable and easy to maintain. The range features proven designs with powerful engines from well known manufacturers.
Chicago Pneumatic Construction Equipment distributors are tool and compressor experts who can precisely match the performance characteristics of CP tools to your specific job requirements.
For tools, parts and accessory information, and for service, contact a CP Construction Equipment distributor nearest you. Find them listed on the web at www.cp.com, or by calling a customer service representative toll-free at 800-760-4049.
Limited Warranty
Products of the Chicago Pneumatic Brand (CP) are warranted to be free from defects in material and workmanship for one year from the date of purchase.
This warranty applies only to products purchased new from CP or its authorized dealers. Of course, this warranty does not apply to products which have been abused, misused, modified or repaired by someone other than CP or its Authorized Service Representatives.
If a CP product proves defective in material or workmanship within one year after purchase, return it to any Chicago Pneumatic Authorized Service Center for CP tools, transportation prepaid, enclosing your name and address, adequate proof of date of purchase and a short description of the defect. CP will, at its discretion, repair or replace defective products free of charge. Repairs or replacements are warranted as described above for the remainder of the original warranty period. CP’s sole liability and your exclusive remedy under this warranty is limited to repair or replacement of the defective product. There are not other warranties expressed or implied and CP shall not be liable for incidental, consequential or special damages, or any other damages, costs, or expenses excepting only the cost or expense of repair or replacement as described above.
A History of Unequaled Quality
In 2009, Chicago Pneumatic Tool Company (CP) celebrated 108 years as a pioneer and market leader in the pneumatic tool industry. When the company incorporated more than a century ago, pneumatic tools were a revolutionary new technology. J.W. Duntley, an ambitious foreman in a Milwaukee foundry, recognized the potential in these tools and set out to pursue his American dream.
With keen intellect and little money, he partnered with young steel tycoon Charles Schwab to manufacture and market air tools under the Chicago Pneumatic name. At
that time, most manufacturers specialized in creating only one type of tool. Duntley realized that if Chicago Pneumatic could manufacture and sell a complete line of pneumatic tools, it could provide superior service. In a sense, he had the vision for one-stop shopping for the pneumatic tool industry long before it became the norm.
He did not, however, realize his company would have such an impact on the world. As the industry’s most experienced manufacturer, Chicago Pneumatic has developed tools that were used to build and main-tain some of the world’s most recognizable landmarks. CP impact wrenches and rivet busters were used to construct iconic and engineering marvels such as the Empire State Building and the Golden Gate Bridge. The company’s concrete vibrators were partially responsible for the construction of the Hoover Dam, one of America’s “seven modern civil engineering wonders”.
When the United States found itself embroiled in World War II, CP produced the tools necessary to fabricate, assemble and maintain the nation’s military equipment. And in addition to helping the nation’s defense, one Chicago Pneumatic tool became part of an icon that symbolizes American character and courage. In the painting “Rosie the Riveter”, by legendary illustrator Norman Rockwell, the well-recognized factory worker eats her lunch with a CP riveting hammer lying on her lap.
Chicago Pneumatic continued to expand its global business as the century progressed, and even began making its mark on space travel. During the late 1960s and early 70s, in the Apollo program, the United States sent men into space and explored the moon. What is arguably the most technologically advanced organization in the world depended on Chicago Pneumatic tools for the safety of the astronauts. NASA used Chicago Pneumatic’s air motors in the Apollo space capsules, employing them to rotate the capsules upon their return to Earth, ensuring that the exit hatches faced up and out of the sea, making exit safe for the astronauts.
J.W. Duntley signed the incorporation papers for Chicago Pneumatic Tool Company in New Jersey in December of 1901. More than one hundred years ago, he could not have known that the tools his company crafted would help to build at least four of the “Top Ten Construction Achievements” of the 20th century. Nevertheless, perhaps he did realize, all those years ago, that the brand he built and the commitment to quality he instilled would make CP tools the first choice of generations of people around the world.
Table of Contents
Percussion Tool Safety 4
Breakers—4-Bolt 6
Rivet Busters 9
Spike Drivers 12
Clay Diggers & Picks 12
Scabblers 13
Combi Drills / Hammers 14
Sinker Drills 15
Chipping Hammers 16
Tampers 21
Pumps 22
Vibrators 24
Cut-off Saw 24
Core Drill 25
Air Line Accessories 26
Compressors 27
RCP Compressors 32
Aftermarket 33
Gas Powered Breakers 34
Chisels 36
Hydraulic Tools 37
RX Hydraulic Breakers 44
Generators 50
Percussion Tool Safety
Riveting and chipping hammers, demolition tools, rock drills, tampers and rammers
The goal of Chicago Pneumatic is to produce tools that help you work safely and efficiently. The most important safety device for this or any tool is the operator. Care and good judgment are the best protection against injury.
All possible hazards cannot be covered here, but we have tried to highlight some of the most important ones.
Before operating any Chicago Pneumatic tool, always read the safety instructions that accompany each tool. All Chicago Pneumatic tools supplied with retainers and guards should have these parts properly secured in place during operation.
For Additional Safety Information Consult:
• Other documents and information packed with the tool• Your employer, union and/or trade association• U.S. Department of Labor (OSHA); Council of the European Communities and/or local codes.• “Safety Code for Portable Air Tools” (ANSI B186.1) is available from: American National Standards Institute, Inc., 11 W. 42nd Street, New York, NY 10036• “Safety Requirement for hand-held non-electric power tools” is available from: European Committee for Standardization, Rue de Stassart 36, 1050 Brussels, Belgium.
Air Supply and Connection Hazards
• Air under pressure can cause severe injury.• Always shut off air supply, drain hose of air pressure and disconnect tool from air supply when not in use, before changing accessories or when making repairs.• Never direct air at yourself or anyone else.• Whipping hoses can cause serious injury. Always check for damaged or loose hoses and fittings.• Do not use quick disconnect couplings at tool. See instructions for correct setup.• Whenever universal twist couplings are used, lock pins must be installed.• Do not exceed maximum air pressure of 90 psi or as stated on tool nameplate.
Projectile Hazards
• Always wear impact-resistant eye and face protection when involved with or near the operation, repair or maintenance of the tool or when changing accessories on the tool.• Be sure all others in the area are wearing impact-resistant eye and face protection.• Never operate a tool unless the accessory is retained in the tool with a proper retainer. Please refer to the appropriate parts list.• To avoid injury, retainer parts must be replaced when they become worn, cracked or distorted.• Wear a safety helmet.
4
Operating Hazards
• To prevent damage to both tool and accessory, accessory must be held firmly against the work surface before tool is throttled.• Always shut off the air supply, relieve hose of air pressure and disconnect tool from air supply when changing accessories.• Avoid direct contact with accessory and work surface during and after work as they become heated and sharp.• Wear gloves to protect hands.• Operators and maintenance personnel must be physically able to handle the bulk, weight and power of the tool.• Holding the accessory with the free hand can be a source of vibration exposure or injury.• To avoid injury from entanglement, do not wear loose clothing when using a rock drill.• Wear safety shoes, especially when collaring steels or tamping.• Only use the machine for the jobs for which it is intended.
Accessory Hazards
• Never use any chisel as a hand struck tool. They are specifically designed and heat-treated to be used only in air hammers.• Select the correct shank and retainer for the tool being used.• Never use dull accessories, as they require excessive work pressure and can break from fatigue.• Never cool a hot accessory in water. Brittleness and early failure can result.• Chicago Pneumatic tools and accessories must not be modified in any way.• Chicago Pneumatic percussion tools are not intended for use with any accessories that are not listed in the catalog.• Accessory breakage or tool damage may result from prying. Take smaller bites to avoid getting struck.
Workplace Hazards
• Slipping, tripping and falling are major causes of serious injury or death. Be aware of excess hose left on the walking or work surface.• High sound levels can cause permanent hearing loss. Use hearing protection as recommended by your employer or OSHA regulation (see 29 CFR part 1910).• Maintain a balanced body position and secure footing.• Repetitive work motions, awkward positions and exposure to vibration can be harmful to hands and arms. If numbness, tingling, pain or whitening of skin occurs, stop using the tool and consult a physician.• Avoid inhaling dust or handling debris from the work process that can be harmful to your health.• Proceed with care in unfamiliar surroundings. Hidden hazards may exist, such as electric or other utility lines.• Chicago Pneumatic tools are not intended for use in explosive atmospheres and are not insulated for contact with electric power sources.• A used machine shall be treated and disposed of in such a way that the greatest possible part of the material can be recycled and the influence on the environment is kept as low as possible.
5
Breakers — 4-Bolt High Performance Models
Model Part number Standard hex chuck size
(in)
Retainertype
Length
(in)
Weight
(lb)
Shipping weight
(lb)
CP 0112—30-pound class—air consumption at 90 psi: 45 cfm
CP 0112 8900 0030 23 1 x 41/4 Latch 20 30 36
CP 0112 EX 8900 0030 24 1 x 41/4 Latch 303/8 33 39
CP 0112 S 8900 0030 25
CP 1210—35-pound class—air consumption at 90 psi: 48 cfm
CP 1210 8900 0030 01 1 x 41/4 Latch 211/8 44 47
CP 1210S 8900 0030 03 1 x 41/4 Latch 211/8 48 49
CP 1210S 8900 0030 09 11/4 x 6 Latch 23 49
CP 1210S 8900 0030 07 11/8 x 6 Latch 23 49
CP 1210 SVR 8900 0030 05 1 x 41/4 Latch 231/2 51 57
CP 1210 SVR 8900 0030 08 11/8 x 6 Latch 251/2 55
CP 1210 SVR 8900 0030 10 11/4 x 6 Latch 251/2 55
CP 1230—60-pound class—air consumption at 90 psi: 63 cfm
CP 1230 T022073 11/8 x 6 Latch 261/2 65 66
CP 1230 S T022158 11/8 x 6 Latch 261/2 68 68
CP 1230 SVR T024227 11/8 x 6 Latch 271/2 76 81
CP 1230 T022074 11/4 x 6 Latch 261/2 65 66
CP 1230 S T022159 11/4 x 6 Latch 261/2 68 68
CP 1230 SVR T024239 11/4 x 6 Latch 271/2 76 81
CP 1240—90-pound class—air consumption at 90 psi: 81 cfm
CP 1240 T022075 11/8 x 6 Latch 283/4 83 89
CP 1240 S T022221 11/8 x 6 Latch 283/4 86 92
CP 1240 SVR T024536 11/8 x 6 Latch 30 95 98
CP 1240 T022076 11/4 x 6 Latch 283/4 83 89
CP 1240 S T022222 11/4 x 6 Latch 283/4 86 92
CP 1240 SVR T024535 11/4 x 6 Latch 30 95 98
EX = Extended handle for trench work; S = Silenced models; SVR = Silenced Vibration + reduced models
66
CP Four-bolt breakers require minimal servicing to maintain peak operating efficiency over extended periods of rugged use.
Oversized springs, side bolts and anvil minimize repairs.
CP Breakers can be ordered with mufflers, or mufflers can be purchased separately.
Breakers
7
Breakers — 4-Bolt High Performance Models
CP 1230 and CP 1240
The CP 1230 (60-pound class) and CP 1240 (90-pound class) demolition tools are engi-neered to deliver the power and durability necessary for a variety of construction and plant maintenance applications such as breaking heavy and reinforced concrete, frozen ground, asphalt, boulders and pavement.
Features• Alloy steel forgings provide excellent durability• Four-bolt backhead design withstands rugged use• Integral oiler provides continuous lubrication• Heavy-duty front headsprings reduce reaction back to operator• Reversible piston reduces maintenance cost• Air inlet swivel for easy maneuverability• CP 1230S and CP 1240S are equipped with silencers• Vibration reduced handle (SVR) available on the CP 1230 SVR and CP 1240 SVR
Vibration reduced models (VRS)are also silenced.
1210 SVR 1230 SVR 1240 SVR
Breakers can be ordered with mufflers or mufflers can be
purchased separately.
CP1210S
Standard model CP 1210, 1230 and 1240
CP 0112 and CP 1210
The CP 0112 (30-pound class) and CP 1210 (35-pound class) demolition tools are light-weight yet rugged. They’re designed for light to medium construction and plant maintenance work such as demolition of floors, pavement, bridge maintenance, asphalt, frozen ground and masonry walls. They’re very popular for bridge deck jobs. CP 0112 EX has an extend-ed handle for trench work.
Features• Alloy steel forgings provide excellent durability• Four-bolt backhead design withstands rugged use• Integral oiler provides continuous lubrication• Heavy-duty front headsprings on CP 1210 reduce reaction back to operator• CP 1210S is equipped with a silencer to reduce sound level• Vibration reduced handle (SVR) is available on the CP 1210 SVR
Replacement Parts
8
Contents of Side Bolt Kits
ModelCP 1210
(Steel spring) 1”
CP1210 (PU spring)
1-1/8” and 1-1/4”CP 1230 CP 1240
Kit article no. 3303 0050 44 3303 0050 45 3303 0050 56 3303 0050 57
Contents
2 x side bolt R 110217 R 110217 R 047970 F 037790
2 x nut - side bolt R 110218 R 110217 R 047970 F 037789
2 x lock washer - nut R 041073 R 041073 R 090584 R 096059
2 x front head spring R 093698 3303 0050 33 R 047971 R 092915
Product CP 1210 CP 1230 CP 1240
Contents
Contents of Latch Kits
Retainer latch kits include: latch, latch bushing, bolt or pin, and other parts needed to safely and easily replace worn or broken latches
Side bolt kits include: two each of side rod bolts, nuts, springs and lock washers
Breakers
Pound for pound, there is no hammer with more hitting power than a rivet buster. Even a paving breaker would need to be at least twice as heavy to deliver an equivalent blow. This super-power can still be controlled thanks to low blow frequency and teasing throttle. That’s why the rivet buster is one of the favor ite tools of demolition contractors in the US. Users have discovered many new applications for rivet busters for working in both concrete and steel. No longer is the bus-ter used exclusively by iron workers for form-ing and cutting rivets, but it has now found its way into the hands of operators who need the most powerful tool for the job.
Concrete applications
• Bridge deck work, where weight of breakers is restricted
• De-capping foundation pillars, where concrete is very hard
• Medium to heavy concrete demolition • As an alternative to paving breakers where high
hitting power is required but applied in a restrained space or working horizontally
Metal applications
• Cutting and removing large rivets and bolts with narrow chisels and backout punch, or other spe-cial steel and accessories
• Cutting metal tanks or plates (3/16” thick, 5 mm) with ripper chisel
• Industrial applications such as foundries or the petrochemical industry with beryllium chisels
9
Special Jumbo Shank steel accessories for rivet busters
Rivet Busters for both metal and concrete applications
River Busters
“D” handle
Open grip handle
Rubber bumper3303 0051 03
Part no. Model Weight (lb)
Blows per minute
(bpm)
Cylinder stroke
(in)
Length (in)
Air consumption
(cfm)
Air inlet (in)
Chuck size (Jumbo Shank)
Handle Cylinder
8900 0001 49 4608 P 30 1080 8 23 45 1/2 .890” x 1.125” Taper Open grip-Outside trigger Short cylinder
8900 0001 50 4611 P 33 720 11 26 45 1/2 .890” x 1.125” Taper Open grip-Outside trigger Long cylinder
8900 0001 51 4608 D 31 1080 8 23 45 1/2 .890” x 1.125” Taper “D” handle-Inside trigger Short cylinder
8900 0001 52 4611 D 34 720 11 26 45 1/2 .890” x 1.125” Taper “D” handle-Inside trigger Long cylinder
10
Originally designed for cutting and forming metal rivets, the CP buster is now used for concrete demolition and has become one of the stars of the CP range. It has a low frequency blow with hitting power equivalent to a paving breaker twice its weight. The new CPS includes a stepped piston and step cylinder to prevent accidental ejection of the piston.
• Teasing throttle for progressive hitting frequency gives better control of such a powerful machine
• Special Boyer valve makes the cylinder stroke effectively longer for more hitting power
• Boyer valve’s high quality design makes the blow more consistent
• Forged steel handle for long life in rugged condi-tions
• Stepped piston of hardened steel
• New buffer ring is now 90 durometer rubber for extra life
• Stepped piston to prevent accidental ejection of the piston
• Choice of cylinders: 11” cylinder (720 bpm) 8” cylinder (1080 bpm)
• Choice of handle: Open grip with outside trigger “D” handle with inside trigger
• 1/2 ” inlet bushing
With each buster, it is recommended that you also purchase these additional consumable items: a rubber bumper (3303 0051 03), lower sleeve (P072333), upper sleeve (P156988), retainer spring (P073942) and whip hose (9246 0203 64).
4608 P - 8” OPEN HANDLE 4608 D - 8” D-HANDLE
CPS Control Power System The wear indicating groove (l) on the lower sleeve indicates that the bumper is completely worn out and needs to be replaced.
When the bumper is 75% worn out, the bleeding ports (J) are opened due to the outward movement of the upper and lower sleeves, causing the piston to stop in its lower position and the air to the exhaust above retainer.
Continuing to use the buster when the auto-matic stop function has triggered may cause damage to the sleeves and possibly the cylinder.
A. Lower sleeve B. Bumper C. Upper sleeve
Rivet Busters with CPS
Rivet Busters with CPS
4611 P - 11” OPEN HANDLE 4611 D - 11” D-HANDLE
Key features
Description Type of Part Number Tip width/ Length Weight body Bladesize overall (in) (in) (lbs.)
Moil 3083 4140 00 10 2point 3083 4140 10 12 2 1/2
3083 4140 20 18 4
Narrow 3083 4141 00 1 10 2Chisel 3083 4141 10 1 12 2 1/2
3083 4141 20 1 18 4
Loose 3083 4142 00 1 1/8 10 2Rivet 3083 4142 10 1 1/8 12 2 1/2
Buster 3083 4146 20 1 1/8 18 4
Tight 3083 4145 00 1 1/8 10 2Rivet 3083 4145 10 1 1/8 12 2 1/2
Buster 3083 4145 20 1 1/8 18 4
Drift 3083 4143 00 7/8 dia. 7 1/2 1 1/2
PinDriver
Ripper 3083 4144 00 9 1 3/4
Backout 3083 4148 10 5/8 10 1 3/4
Punch 3083 4148 20 5/8 12 1 3/4
3083 4148 40 3/4 10 2 3083 4148 50 3/4 12 2 3/4 3083 4148 70 7/8 10 2 3/4
3083 4148 80 7/8 12 3
Line oilers
Water separator
HEAVY DUTY RIVET BUSTER STEEL
Consumables and accessories Consumables and accessories for rivet busters using jumbo steels
Blade width Length o/a Weight Price
inches inches lbs. $
3083 4140 00 10 2 28.05
3083 4140 10 12 2.1/2 33.65
3083 4140 20 18 4 46.00
3083 4141 00 1 10 2 28.05
3083 4141 10 1 12 2.1/2 33.65
3083 4141 20 1 18 4 46.00
3083 4142 00 1.1/8 10 2 31.40
3083 4142 10 1.1/8 12 2.1/2 37.00
3083 4146 20 1.1/8 18 4 57.20
3083 4145 00 1.1/8 10 2 44.90
3083 4145 10 1.1/8 12 2.1/2 53.85
3083 4145 20 1.1/8 18 4 67.30
3083 4143 00 7/8 dia. 7.1/2 1.1/2 53.85
3083 4144 00 9 1.3/4 50.50
3083 4147 00 1/2 9.3/4 1.1/2 35.90
3083 4147 10 5/8 9.3/4 1.3/4 38.15
3083 4147 20 3/4 9.1/2 1.3/4 38.15
3083 4147 30 3/4 12 2.1/2 35.90
3083 4147 40 7/8 9.1/2 2 38.15
3083 4147 50 7/8 12 2.3/4 37.00
3083 4147 60 1 9.1/2 2.1/2 40.40
3083 4147 70 1 12 2.3/4 47.10
Loose
Rivet
Buster
HEAVY DUTY RIVET BUSTER STEEL
Moil
Point
Narrow
Chisel
Type of Working EndType of
bodyPart Number
Jumbo 11X
Tight
Rivet
Buster
Drift Pin
Driver
Backout
Punch
Ripper
3/4
7/81.1/8
2.3/8
1.3/4
- 7 -
Blade width Length o/a Weight Price
inches inches lbs. $
3083 4140 00 10 2 28.05
3083 4140 10 12 2.1/2 33.65
3083 4140 20 18 4 46.00
3083 4141 00 1 10 2 28.05
3083 4141 10 1 12 2.1/2 33.65
3083 4141 20 1 18 4 46.00
3083 4142 00 1.1/8 10 2 31.40
3083 4142 10 1.1/8 12 2.1/2 37.00
3083 4146 20 1.1/8 18 4 57.20
3083 4145 00 1.1/8 10 2 44.90
3083 4145 10 1.1/8 12 2.1/2 53.85
3083 4145 20 1.1/8 18 4 67.30
3083 4143 00 7/8 dia. 7.1/2 1.1/2 53.85
3083 4144 00 9 1.3/4 50.50
3083 4147 00 1/2 9.3/4 1.1/2 35.90
3083 4147 10 5/8 9.3/4 1.3/4 38.15
3083 4147 20 3/4 9.1/2 1.3/4 38.15
3083 4147 30 3/4 12 2.1/2 35.90
3083 4147 40 7/8 9.1/2 2 38.15
3083 4147 50 7/8 12 2.3/4 37.00
3083 4147 60 1 9.1/2 2.1/2 40.40
3083 4147 70 1 12 2.3/4 47.10
Loose
Rivet
Buster
HEAVY DUTY RIVET BUSTER STEEL
Moil
Point
Narrow
Chisel
Type of Working EndType of
bodyPart Number
Jumbo 11X
Tight
Rivet
Buster
Drift Pin
Driver
Backout
Punch
Ripper
3/4
7/81.1/8
2.3/8
1.3/4
- 7 -
Blade width Length o/a Weight Price
inches inches lbs. $
3083 4140 00 10 2 28.05
3083 4140 10 12 2.1/2 33.65
3083 4140 20 18 4 46.00
3083 4141 00 1 10 2 28.05
3083 4141 10 1 12 2.1/2 33.65
3083 4141 20 1 18 4 46.00
3083 4142 00 1.1/8 10 2 31.40
3083 4142 10 1.1/8 12 2.1/2 37.00
3083 4146 20 1.1/8 18 4 57.20
3083 4145 00 1.1/8 10 2 44.90
3083 4145 10 1.1/8 12 2.1/2 53.85
3083 4145 20 1.1/8 18 4 67.30
3083 4143 00 7/8 dia. 7.1/2 1.1/2 53.85
3083 4144 00 9 1.3/4 50.50
3083 4147 00 1/2 9.3/4 1.1/2 35.90
3083 4147 10 5/8 9.3/4 1.3/4 38.15
3083 4147 20 3/4 9.1/2 1.3/4 38.15
3083 4147 30 3/4 12 2.1/2 35.90
3083 4147 40 7/8 9.1/2 2 38.15
3083 4147 50 7/8 12 2.3/4 37.00
3083 4147 60 1 9.1/2 2.1/2 40.40
3083 4147 70 1 12 2.3/4 47.10
Loose
Rivet
Buster
HEAVY DUTY RIVET BUSTER STEEL
Moil
Point
Narrow
Chisel
Type of Working EndType of
bodyPart Number
Jumbo 11X
Tight
Rivet
Buster
Drift Pin
Driver
Backout
Punch
Ripper
3/4
7/81.1/8
2.3/8
1.3/4
- 7 -
Blade width Length o/a Weight Price
inches inches lbs. $
3083 4140 00 10 2 28.05
3083 4140 10 12 2.1/2 33.65
3083 4140 20 18 4 46.00
3083 4141 00 1 10 2 28.05
3083 4141 10 1 12 2.1/2 33.65
3083 4141 20 1 18 4 46.00
3083 4142 00 1.1/8 10 2 31.40
3083 4142 10 1.1/8 12 2.1/2 37.00
3083 4146 20 1.1/8 18 4 57.20
3083 4145 00 1.1/8 10 2 44.90
3083 4145 10 1.1/8 12 2.1/2 53.85
3083 4145 20 1.1/8 18 4 67.30
3083 4143 00 7/8 dia. 7.1/2 1.1/2 53.85
3083 4144 00 9 1.3/4 50.50
3083 4147 00 1/2 9.3/4 1.1/2 35.90
3083 4147 10 5/8 9.3/4 1.3/4 38.15
3083 4147 20 3/4 9.1/2 1.3/4 38.15
3083 4147 30 3/4 12 2.1/2 35.90
3083 4147 40 7/8 9.1/2 2 38.15
3083 4147 50 7/8 12 2.3/4 37.00
3083 4147 60 1 9.1/2 2.1/2 40.40
3083 4147 70 1 12 2.3/4 47.10
Loose
Rivet
Buster
HEAVY DUTY RIVET BUSTER STEEL
Moil
Point
Narrow
Chisel
Type of Working EndType of
bodyPart Number
Jumbo 11X
Tight
Rivet
Buster
Drift Pin
Driver
Backout
Punch
Ripper
3/4
7/81.1/8
2.3/8
1.3/4
- 7 -
11
RedX Hose 8900 0050 08
Part no. Description
P 072 333 Lower sleeve
P 156 988 Upper sleeve
3303 0051 03 Rubber bumper
P 073 942 Retainer Spring (standard
9246 0203 72 Air swivel 1/2” NPT
9246 0203 69 Lubricator comp 3/4” NPT - 5oz
9246 0206 64 Lubricator comp 3/4” NPT - 8oz
9246 0203 68 Lubricator comp 3/4” NPT - 11oz
8900 0050 01 Water separator 3/4” NPT thread
8099 0202 43 Airoline oil 1L
9246 0203 64 Whip hose with swivel 1/2” NPT
9246 0203 61 Whip hose w/5 oz oiler and swivel
9246 0203 91 Whip hose w/11 oz oiler and swivel
Spike Drivers
Chicago Pneumatic spike drivers are rugged, powerful tools which can be used for driving spikes in railroad, construction and plant maintenance applications.
Model Part number Length
(in)
Max head diameter
(in)
Weight
(lb)
Shippingweight
(lb)
CP 1230—Air consumption at 90 psi: 63 cfm
CP 1230 SPDR T021612 241/2 17/8 60 65
CP 1230 S SPDR T021613 241/2 17/8 60 65
CP 1240—Air consumption at 90 psi: 81 cfm
CP 1240 SPDR T021042 241/2 17/8 81 86
CP 1240 S SPDR T021041 241/2 17/8 81 86
Clay Diggers and Picks
Clay diggers and picks are well suited for trenching and tunneling. Their light weight makes them ideal for overhead work and light demolition.
Model Part number
Standardhex chuck
(in)
Bore andstroke
(in)
Throttletype
Length
(in)
Weight
(lb)
CP 0111 —Air consumption at 90 psi: 45 cfm, 3/8” (NPT) air inlet thread
CP 0111 CHIT 8900 0001 41 7/8 x 31/4 1.63 x 3.5 inside trigger 221/2 29
CP 0111 CHLA 8900 0001 20 1 x 41/4 1.63 x 3.5 outside trigger 221/2 29
CP 0222—Air consumption at 90 psi: 44 cfm, 1/2” (NPT) air inlet thread
CP 0222 CHIT 8900 0001 21 7/8 x 31/4 1.6 x 3.38 inside trigger 191/2 22
CP 0222
CP 1230 SPDR
• Heat-treated alloy steel components for excellent durability• Spike driver front hood • Built in lubricator
CP 1240 SPDR
• Lightweight and compact for easy handling• High power-to-weight ratio• Spike driver front hood • Built in lubricator
CP 0111
• Heat-treated alloy steel components for excellent durability• Latch retainer• High power-to-weight ratio
CP 0222
• Lightweight and compact for easy handling• High power-to-weight ratio• Latch retainer
CP 1240 S SPDR
CP 1230 S SPDR
12
Spike Drivers, Clay Diggers and Picks
CP 0111
Scabblers
Scabblers are ideal for cleaning and roughing concrete and construction joints. They can also be used to produce ornamental or contrasting finishes on building structures.
Model Part number bpmper piston
Bore
(in)
Stroke
(in)
Weight Length Height (pistonsextended)
(in)
Width
(in)
Number/typeof pistons
All models—Air consumption at 90 psi: 29 cfm, 1/2” (NPT) air inlet thread
CP 0006* T022137 3000 1 1 10 16 7 4 Three 4-point carbide tipped
CP 0066* T024412 3000 0 1 10 11 5 2 3
*Use whip hoses on page 11 for Rivet Busters
Replacement pistons Model Part number
CP 0006 F064604
CP 0066 R145921
Piston caps(order one for each replacement piston) Model Part number
CP 0006 F826706
CP 0066 R147614
Replacement parts
13
Scabblers
CP 0006
• Lightweight, compact tool with contoured grip handle reduces operator fatigue and increases output• Tungsten carbide-tipped pistons last longer and are easily replaced• Back head grip gives in-line thrust• Chamfered cylinder block increases visibility of the work piece permitting close operation in tight corners
CP 0066
• Lightweight, compact tool with contoured grip handle reduces operator fatigue and increases output• Tungsten carbide-tipped pistons last longer and are easily replaced• Chamfered cylinder block increases visibility of the work piece permitting close operation in tight corners
CP 0006
CP 0009
CP 0014
Combi Drills / Hammers
All Models
• Excellent power-to-weight ratio helps drill holes faster and easier than comparable electric rotary hammers• Built-in oiler provides continuous lubrication• Teasing throttle for precise control• Rotation release button converts tool to a hammer (except on CP 0009AC)• Cushioned piston for smooth operation and long tool life• Muffler available to reduce noise
CP 0009
• Right hand rotation• With an adaptor, can be used with electric hammer drill bits• Spline version available• Adapter (R137586) round to SDS
CP 0014
• Superior drilling rates• Greater drilling capacity compared to plug hole drills• Designed for production drilling of small holes
Model Partnumber
Netweight
(lb)
Overalllength
(in)
Typeof chuck
(in)
Chuck size(in)
CP 0009—Air consumption at 90 psi: 20 cfm, 3/8” (NPT) air inlet thread
CP 0009 A T022083 8 143/4 round shank 3/4 x 33/4
CP 0009 AC* Z0027413 8 143/4 round shank 3/4 x 33/4
CP 0009 F T022511 8 143/4 spline drive
CP 0014 RR—Air consumption at 90 psi: 32 cfm, 3/8” (NPT) air inlet thread
CP 0014 RR T022173 15 181/2 spring hex shank 7/8 x 31/4
* without stop rotation, round shank steels, eliminate rotation.
Drilling rates in hard rock and concrete(use as guide only)
Model Drill rate(in/min)
Hole diameter(in)
CP 0009 12 11/4
CP 0014 RR 18 13/4
Mufflers Model Part no.
CP 0009 A F815350
CP 0009 AC F826972
CP 0009 F F815350
CP 0014 RR F827044
These versatile tools are both a drill and a chipping hammer. A push of the rotation release button easily and quickly converts the tool to a hammer.
The CP 0009 and CP 0014RR rotary hammers are designed for a wide variety of construction and maintenance applications such as driving or setting masonry anchors and drilling holes in concrete, bricks or rock. As a hammer, these tools can be used for chipping, scarifying, scaling and cleaning welds.
14
Rock Drills
CP 0032A
Sinker Drills
All Models
• Forged steel housings withstand rugged use• Cushioned piston reduces shock• Multiposition throttle for easy starting of holes• Blower lever for deep hole cleaning on CP 0032 and CP 0069• Integral oiler provides continuous lubrication• 3/4” (NPT) air inlet swivel improves maneuverability• Double-grip handles • Left hand rotation
CP 0022
30-pound classThe CP 0022 provides drilling capability for holes up to 13/4” diameter, 8 feet deep. This is the ideal choice where a lightweight and powerful tool is needed in public works, utilities and drilling from scaffolding. Also the correct choice where air supply is limited. CP 0022 can also be equipped with 3/4” x 41/4” bushing and spring
CP 0032A
45-50-pound classChoose the CP 0032A for holes up to 2” diameter and 10 feet deep. A top performer in its class, the CP 0032A is highly effective in general excavation work, quarry drilling, bench mining and other jobs requiring a sinker drill in the 45-pound class. The tool’s durable “beavertail” retainer helps it deliver increased contact and reduces collar wear.
Use with part number R147457 - Water Kit for use with flushing water
CP 0069
60-pound classThe CP 0069 is suited for drilling 21/2” diameter holes 20 feet deep. The heavy-duty CP 0069 sinker is a hard-hitting tool that combines high drilling speed with excellent hole cleaning ability. Its trouble-free “beavertail” retainer provides greater front-end durability and increased collar contact to reduce wear.
Model Part number
Netweight
(lb)
Overall lengthwith retainer
(in)
Standard hex. chuck size
(in)
CP 0022—30-pound class—Air consumption at 90 psi: 56 cfm
CP 0022 8900 0020 01 28 197/8 7/8 x 31/4
CP 0022 8900 0020 02 28 197/8 7/8 x 41/4
CP 0032—45- to 50-pound class—Air consumption at 90 psi: 103 cfm
CP 0032A .87 T022318 54 22 7/8 x 31/4
CP 0032A .87 A T022117 54 23 7/8 x 41/4
CP 0032A-1 T022319 54 23 1 x 41/4
CP 0069—60-pound class—Air consumption at 90 psi: 130 cfm
CP 0069 T006661 64 241/4 7/8 x 41/4
CP 0069 T022259 64 241/4 1 x 41/4
CP 0069 - wet T025423 64 241/4 7/8 x 41/4
Comfort handle options
CP 0022, CP 0032A, and CP 0069 can also be equipped with a comfort handle (order kit: R154915).
Model Drill rate(in/min)
Hole diameter (in)
CP 0022 6.0 15/8
CP 0032 9.0 13/4
CP 0069 10.2 13/4
Drilling rates in hard rock(use as guide only)
Chicago Pneumatic sinker drills are ideal for a range of drilling applications. Their streamlined design incorporates smooth contours, a side exhaust and a “flat back” that makes them easy to handle in quarry, mine, drilling and doweling work. The design also provides a main valve and cylinder-porting concept that helps maintain constant drilling speed throughout a long service life. Working parts are continually protected with an effective lubrication system. Standard and silenced versions are available in a range of weights and sizes to fit any requirement.
15
CP 0022
Model Part number
CP 0032A R125569
CP 0069 R278142
Mufflers
CP 0012 handle based on the well known CP 0009 design
CP 4123 with simplate valve
CP 4125 now has a unique ring valve design as standard
CP 4125 special heat treated cylinders with chrome plated bores
for extra durability
CP 4130 four bolt flange for in-creased durability, strength and ease
of service
0012, a new 12 lb. hammer for light chipping, and additional features on the classics – CP 4123 and CP 4125 hammers – for extra toughness and reliability.
Chipping Hammers
With 2”, 3” and 4” cylinder options, Chicago Pneumatic offers a very complete range of chipping hammers for all types of con struction and industrial applications. Introducing CP
CP 0012
CP 4123
CP 4130
• Locking mechanism with four high strength ½” bolts• ”D” handle with outside trigger and extra safety mechanism• Muffler assembly as standard• Simplate valve for smooth operation• Strong and reliable• Available in 3” or 4” cylinder stroke versions• Choice of bushing: .680” Round chisel rotates freely .580” Hex prevents chisel rotation
• Powerful, yet compact and lightweight• Rugged construction, hardened steel cylinder and handle• Teasing throttle for precise control• Open grip handle with self closing outside trigger
• Available in 2”, 3” or 4” cylinder stroke versions• Choice of bushing: .680” Round chisel rotates freely .580” Hex prevents chisel rotation
• Classic simplate valve• Heat treated cylinder• Now with spline lock instead of clip locking mechanism
• Unique ring valve as standard for harder blow in tough applications or dirty environments• Chrome plated cylinder for extra durability• Spline locking to prevent loosening of handle or cylinder
CP 4125
CP 4123 and CP 4125
Chipping Hammers
CP 4132
Chipping hammers for construction and industrial applications
Part no. Model Old model name Weight
(lb)
Cylinder stroke
Length
(in)
Blows per minute (bpm)
Air consumption
(cfm)
Muffler included as standard
Chuck size
(in)
8900 0001 02 CP 0012 2ßR – 12 2 16 2600 20 yes .680” Rnd
8900 0001 03 CP 0012 2H – 12 2 16 2600 20 yes .580” Hex
8900 0001 04 CP 4123 2R CP 4123 PYRA 13 2 127/8 2400 25 – .680” Rnd
8900 0001 05 CP 4123 2H CP 4123 PYRE 13 2 127/8 2400 25 – .580” Hex
8900 0001 06 CP 4123 3R CP 4123 PYSA 141/4 3 147/8 1920 26 – .680” Rnd
8900 0001 07 CP 4123 3H CP 4123 PYSE 141/4 3 147/8 1920 26 – .580” Hex
8900 0001 08 CP 4123 4R CP 4123 PYTA 151/2 4 151/2 1500 27 – .680” Rnd
8900 0001 09 CP 4123 4H CP 4123 PYTE 151/2 4 151/2 1500 27 – .580” Hex
8900 0001 10 CP 4125 2R CP 4125 PALA 13 2 131/4 2400 26 – .680” Rnd
8900 0001 11 CP 4125 2H CP 4125 PALE 13 2 131/4 2400 26 – .580” Hex
8900 0001 12 CP 4125 3R CP 4125 PAMA 141/4 3 141/4 1920 27 – .680” Rnd
8900 0001 13 CP 4125 3H CP 4125 PAME 141/4 3 141/4 1920 27 – .580” Hex
8900 0001 14 CP 4125 4R CP 4125 PANA 151/2 4 151/4 1500 28 – .680” Rnd
8900 0001 15 CP 4125 4H CP 4125 PANE 151/2 4 151/4 1500 28 – .580” Hex
8900 0001 16 CP 4130 3R CP 4130 3RO 181/2 3 161/2 1920 26 yes .680” Rnd
8900 0001 17 CP 4130 3H CP 4130 3HO 181/2 3 161/2 1920 26 yes .580” Hex
8900 0001 18 CP 4130 4R CP 4130 4RO 191/2 4 173/4 1500 27 yes .680” Rnd
8900 0001 19 CP 4130 4H CP 4130 4HO 191/2 4 173/4 1500 27 yes .580” Hex
9245 9998 00 CP 4132 3R 15 3 17 1800 33.23 .680” Rnd
9245 9997 99 CP 4132 3H 15 3 17 1800 33.23 .580” Hex
9245 9998 98 CP 4132 4R 15 4 17 1800 33.23 .680” Rnd
9245 9998 80 CP 4132 4H 15 4 17 1800 33.23 .580” Hex
3/8” air inlet. All CP hammers are supplied with oval collar retainer as standard. More retainer options are available on page 20.
CP 0012
The CP 0012 is the new addition to the CP range of pneumatic hammers for light chipping and scaling duties. Since the CP 0012 is light and has medium hitting power, it is very easy to handle and control for more precisejobs. Typical applications include alteration work, hole making and trimming.
CP 4123
The most popular CP chipping hammer of all times, the CP 4123 is used for a wide variety of construction and industrial applications, from light to medium chipping to heavy cutting. Choose the cylinder size that best suits your particular application.
CP 4125
The extra features of the CP 4125 make it more suitable for tough constructionand industrial applications, including foundries, shipyards, refineries, or fabrication shops. Even in hot, dirty working conditions, the reliable CP 4125 will consistently hit hard and last longer than conventional hammers.
CP 4130
The CP 4130 hammer is designed to tackle punishing jobs with the hard hitting power that you expect from CP. It is used for medium-duty to heavy-dutychipping, cutting and trimming operations. The four bolt handle provides higher air flow and durability.
CP 4132
A durable 4-bolt chipping hammer with inside trigger and standard retainer.Available in two cylinder sizes to suite your particular application.
17
18
Chipping Hammers
Model Part Number Air consumption
(CFM)
Blowsper minute
Chuck size
(in)
Length
(in)
Net weight
(lb)
CP 0017 8900 0001 36 32 2200 .680 round 151/4 19
CP 0017 8900 0001 37 32 2200 .580 hex 151/4 19
Model Part Number Bore and Stroke(in)
Blows per minute Bushing size(in)
Overall length*(in)
Net weight(lb)
CP 4131 3R 8900 0001 33 3 1900 .680 round 17 1/2 19
CP 4131 3H 8900 0001 34 3 1900 .580 hex 17 1/2 19
Chipping Hammers New Models
Z8389857 Ball type retainer safely secures accessories
CP 4131 features a thread on ball type retainer as standard
NEW! CP 4131
• Lightweight • Easy to use and maintain• Choice of bushing: .680” Round chisel rotates freely .580” Hex prevents chisel rotation• Ball type retainer• D handle with outside trigger
NEW! CP 0017
• Designed for years of trouble-free service • Closed aluminum handle with inside trigger for
maximum effectiveness and operator comfort• Oil-resistant neoprene exhaust deflectors• Available with choice of .580 or .680 round
bushings
Moil point
Wide chisel
Wide chisel
Bushing tool
Steel for chipping hammers and clay diggers
Chipping hammer steel (CP 0012, CP 4123, CP 4125, CP 4130, CP 4131, CP 4132)Hex .580” shank Round .680” shank
Description Tip width/ blade size
Length overall
OVAL collarPart no.
ROUND collarPart no.
OVAL collarPart no.
ROUND collarPart no.
Clay digger steel (CP 0111 and CP 0222)CP 0111—Hex 1” x 41/4” shank CP 0222—Hex 7/8” x 31/4” shank – CP 0222
Description Tip width/ blade size
(in)
Length overall
(in)
Flat to flat
Part no.
Tip width blade size
(in)
Length overall
(in)
Flat to flat
Part no.
Moil point 15 3083 4030 00 14 3083 4050 00
18 3083 4030 10 18 3083 4050 10
24 3083 4030 20 24 3083 4050 20
Narrow chisel 17/8 15 3083 3309 00 1 14 3083 3303 00
11/8 18 3083 4031 10 1 18 3083 4051 10
11/8 24 3083 4031 20 1 24 3083 3304 00
Wide chisel 3 x 2 15 3083 3310 00 3 x 11/4 14 3083 3305 00
3 x 2 18 3083 4032 10 3 x 11/4 18 3083 4052 10
3 x 2 24 3083 4032 20 3 x 11/4 24 3083 4052 20
Bushing tool 2 sq 9 3083 4036 00 2 sq 9 3083 4056 00
Use the most effective steel for your application. Shown below are a selection of the most common types of steel used for the hammers presented in this brochure. For the complete assortment of air line accessories, see pages 20 and 26.
Other lengths of steel accessories are available upon request. See CP Accessories Price List for ordering numbers.
Other lengths of steel accessories are available upon request. See catalog 9800 0362 93 for ordering numbers.
19
Accessories
Line oilersEconomy-type retainer
Water separatorQuick change retainer
Muffler AT Lug-type retainer
Ball-type retainer
Model Part no. Description
Chipping hammer accessories(CP 0012, CP 4123, CP 4125, CP 4130, CP 4131, CP 4132)
Retainers 9245 9970 02 Economy-type retainer, oval collar
9246 00205 01 Ecomomy-type retainer, round collar
P114062 Quick change retainer, oval collar
P092869 AT Lug-type retainer, oval collar
9245 9983 14 Ball-type retainer, round collar
Retainer springs P135246 Polyurethane
P070994 Wire
P139189 Heavy duty wire
Mufflers P125052 CP 4123/CP 4125 muffler assembly
Hose swivels 9246 0203 70 CP 4123/CP 4125/CP 4132 7/8”-24 inlet thread
9246 0203 71 CP 4130/CP 4131 7/8”-24 inlet thread with 3/8” male pipe thread
9246 0203 72 CP Busters, Tampers, Saw 1/2” NPT air inlet thread
Clay digger accessories (CP 0111 and CP 0222)
Mufflers F814133 CP 0111 muffler assembly
R141765 CP 0222 muffler assembly
Air line accessories
In-line oilers 9246 0203 69 Lubricator 5 oz, w/Universal Couplings
Lubricator 8 oz, w/Universal Couplings
9246 0203 68 Lubricator 11 oz, w/Universal Couplings
Water separator 8900 0050 01 3/4” NPT thread
Air-oil 5 litre
For chipping hammers, clay diggers and air line
LubricatorCP’s Lubricator 43 uses the ejector principle to create controlled lubrication. Pick-up assures oil supply regardless of the lubricator’s position.
Model Part No. Max. working pressure
(psi)
Oil tank volume(pints)
Dosage—free air(lb/feet3)
Weight- empty
(lb)
Air flow range: up to 300 cfm; Pressure drop at 90 psi at max flow: 4 psi
Lubricator 43 8900 0050 07 232 2.75 .6 x 105 - 15 x 105 6.6
20
Accessories
NEW! Lubricator 43
• Accepts mineral or synthetic oil• Fitted with US universal claw couplings• 1” inner hose diameter
Backfill Tampers
AccessoriesBackfill tamper butts
Diameter(in)
Material CP 0003 CP 0004RV
21/2 Aluminum - P138879
5 Aluminum P089008 -
61/4 Aluminum - P089050
6 Iron 3303 0050 82
61/4 Iron 3303 0050 81
Pole Butt Iron 3303 0050 84 3303 0050 83
MufflersDescription Part no.
CP 0003 P126126
CP 0004RV P125807
Tamper butts for CP 0003 and CP 0004
Chicago Pneumatic backfill tampers quickly and effectively compact soil around foundations and other structures and are indispensable for compacting backfill in trenches.
The CP 0003 is well equipped to handle light to medium applicationswhile the CP 0004RV is ideal for heavier jobs.
Model Partnumber
Valvetype
Boreand stroke
(in)
Blows perminute
Net weight
(lb)
Overalllength
(in)
Piston rod
Body dia.(in)
Butt size(in)
CP 0003—Air consumption at 90 psi: 18 cfm
CP 0003 T019307 Simplate 117/16 x 6 800 30 52 7/8 5
CP 0004—Air consumption at 90 psi: 28 cfm
CP 0004 T022292 Ring 21/4 x 6 780 42 50 1 61/4
21
Tampers
CP 0003 CP 0004
CP 0003 and CP 0004
• Maximum power—slow, powerful blows efficiently and quickly compact all types of backfill, including clay and soils containing high percentages of finely crushed or powdered material• Heat-treated cylinder and chrome plated piston significantly extend tool life• Adjustable packing maintains a positive air seal• Aluminum butt held with clamp screw for quick, easy replacement• Exhaust deflector directs air, moisture and oil away from operator• Integral oiler continuously lubricates tool during operation • Well-balanced, smooth-operating tool is easily guided by one person• 1/2” (NPT) air inlet thread• For quieter operation, optional mufflers are available
*Use whip hoses on page 11 for Rivet Busters
CP 0010
Chicago Pneumatic’s CP 0010 and CP 0020 sump pumps are designed for high performance and durability which makes them ideal for removing water from trenches, ditches, manholes, industrial sumps and excavations. Both models will pump down to within only 7/8” from base.
CP 0010 has exhaust pipe 1” NPT x 16” long (S038723).
CP 0020 has exhaust pipe 11/4” NPT x 18” long (C086080).
Caution! CP 0010 and CP 0020 pumps are not intended for pumping flammable fluids and must not be used for doing so.
CP 0010 Performance—Air consumption at 90 psi: 100 cfmTotalHead
(ft)
Discharge rate
40 psi(gal/min)
60 psi(gal/min)
80 psi(gal/min)
90 psi(gal/min)
100 psi(gal/min)
10 160 220 240 245 255
20 140 205 230 240 250
30 120 185 215 230 245
40 90 160 200 215 230
50 60 135 175 195 210
60 10 105 155 175 195
70 - 80 130 150 170
24.3 - 60 95 125 155
90 - - 75 105 125
100 - - 55 75 95
Model Partnumber
Min. water depth
(in)
Overallheight
(in)
Heightw/o valve
(in)
Waterdischarge(NPT-in)
Netweight
(lb)
Min. openingpump will enter
(in)
Air inletthread size
(NPT-in)
Recommended hose size
(in)
Motor
(hp)
CP 0010 T022224 7/8 17 1/2 13 3/4 2 33 8 1/4 x 9 3/4 3/4 3
CP 0020 T022185 7/8 16 11 3/4 2 1/2 58 9 x 11 3/4 1 1 4
CP 0020
CP 0020 Performance—Air consumption at 90 psi: 110 cfmTotal Head
(ft)
Discharge rate
40 psi(gal/min)
60 psi(gal/min)
80 psi(gal/min)
100 psi(gal/min)
10 230 285 325 340
20 195 265 315 330
30 150 245 300 320
40 130 220 280 305
50 100 190 260 280
60 65 165 230 260
70 - 125 200 225
80 - 80 160 190
90 - - - 155
22
Pumps
All Models
• Single-stage centrifugal units driven by powerful vane motors
• Double seals protect bearings and motor from water and mud
• Integral oiler provides continuous lubrication• Integral strainer, air inlet valve• Bronze impeller• Cast-iron housing• Air inlet valve
Sump pumps
Sludge pump
Accessories for CP 0077Part number Description
Inlet Hose Nipple F027762 3” unthreaded x 21/2” BSP
Outlet Nipples R146385 21/2” NPT (both ends)
R146383 21/2” NPT street elbow
Model Part number Maximum suction lift (ft at 90 psi)
Maximumhead(ft)
Dischargeoutlet(NPT)
Air Inletthread size
(NPT)
Recommendedhose size
(in)
Netweight
(lb)
CP 0077—Air consumption at 90 psi: 85 cfm
CP 0077 T024005 20** 175** 21/2 3/4 1 152
CP 0077 Performance at 90 psi, zero suction head
Total head(ft)
Discharge rate(gal/min)
25 90
50 78
75 68
100 60
150 48
175 36
CP 0077
• Has no motor or diaphragm to wear out because it operates on venturi/ejector principle • Exhaust muffler reduces sound level
Caution! CP 0077 pumps are not intended for pumping flammable fluids.
** Includes friction head from hose.
23
CP 0077
CP 0077 sludge pumps easily handle water containing 15% solids and particles up to 1” in size. They are suitable for pumping sea water and certain corrosive chemicals.
Concrete Vibrators
Chicago Pneumatic’s CP 2190 heavy duty concrete vibrator is designed for removing air pockets from pourings of low slump concrete in columns, footings, slabs and walls. It has a greater radius of influence which translates to a greater amount of work accomplished in a shorter period of time. And, unlike electric concrete vibrators, there is no chance of shock or need for extension cords.
Model Partnumber
Air consumption
(CFM)
Radius ofinfluence
(in)
Capacity(cu. yds/hr)
Vibrationper
minute
Head dimensions Net weight
(lb)
Length w/o aux. hose
(in)
Averagecfm
Diameter(in)
Length(in)
CP 2190 T019308 65 15 - 16 40 12,000 21/2 133/4 27 118 65
Cut-off Saw
Avoid the daily maintenance associated with gas-powered saws.
The CP 0044 is an extremely durable and powerful air tool driven by a direct drive, 4 hp motor. It is designed to cut a variety of surfaces including concrete, asphalt and stone.
The CP 0044 is engineered for precise balance so less effort is needed to get the job done. A built-in oiler provides continuous lubrication so more time is spent on the job and less time on servicing. Also designed with safety in mind, the CP 0044 features a standard lock-off trigger to help prevent accidental starting. Plus, the blade guard can be operated with one hand.
CP 0044
• Chicago Pneumatic 4 hp motor• One-hand operation blade guard• Integral oiler• Lock-off trigger• Direct drive operation• Two position handle• Well balanced and extremely durable• 1” diameter arbor accepts
industry standard blades
CP 2190
• Variable speed throttle• In-line lubricator• Auxiliary air hose• Locked motor end plates• 1/2” NPT air connection
Model Partnumber
Air consumption
(CFM)
Blade arbordiameter
(in)
No load
(rpm)
Weightwith blade
(lb)
Overall length
(in)
Max. cuttingdepth
(in)
Blade cap (in)
CP 0044 T024421 85 1 4800 28 261/2 4 14
24
Vibrators, Pneumatic Saw
*Use whip hoses on page 11 for Rivet Busters
Chicago Pneumatic’s CP 0315 Core Drill is a powerful, hand-held rotary drill with a threaded output shaft onto which a water swivel and core bit can be fitted. It was originally designed for hand cutting holes in reinforced concrete junc-tion boxes for fiber optic cables. It is now being used in many other sectors of the construction industry for cutting holes in concrete, brickwork and stone and where access or position restricts the use of rig-mounted units. It is also ideal for use in hazardous environments where use of electrical tools is forbidden.
Heavy Duty Core Drill
Model Part No. Free speed(rpm)
Outputshaft
Air inletsize(in)
Length
(in)
Weight
(lb)
CP 0315—Air consumption at 90 psi: 44 cfm
CP 0315 T024733 750 45/64” - 16 tpi 1/2 bsp 13 14
Core Drill AccessoriesDescription Part no.
Water swivel—45/64” input box thread, 1/2” BSP output pin thread 8900 0050 04
Adapter—convert from 1/2” BSP output pin thread to 11/4” UNC output pin thread 8900 0050 05
25
Core Drill
CP 0315
• Core diameter range: 21/2” to 6”• Powerful 1.2 hp air motor• Self-closing twist throttle operation with one-hand control• Governor controlled motor holds speed at heavy loads while increasing power• Integral oil reservoir ensures correct oiling during use• External grease fitting for easy lubrication• Breast-plate for operator comfort during horizontal drilling• Light weight promotes stable operation• Optional adapter (C013048) is available for standard drilling operation
Air line
Description Part no.
CP oiler & separator kit 9245 0204 13
CP water separator 8900 0050 01
lubricator 43 1” NPT 8900 0050 07
CP Red-X hose set US 3/4 ” x 50’ 8900 0050 08
whip hose - 10FT 7/8” - 24 swivel (TEX 317 - 419) 9246 0203 62
whip hose - 10FT 3/8” NPT swivel (All CP chip hammers) 9246 0203 63
whip hose - 10FT - 3/8” NPT swivel & 5oz oiler (all CP chip hammers) 9246 0203 65
whip hose - 10FT - 7/8” - 24 swivel & 5oz oiler (TEX 317-419) 9246 0203 66
lubricator comp 3/4” NPT - 5oz 9246 0203 69
lubricator comp 3/4” NPT - 8oz 9246 0203 64
lubricator comp 3/4” NPT - 11oz 9246 0203 68
CP Airolene Plus tool oil .5L 8099 0202 41
CP Airolene Plus tool oil 1L 8099 0202 43
CP Airolene Plus tool oil 5L 8099 0202 49
CP Airolene Plus rockdrill oil 1L 8099 0201 02
CP Airolene Plus rockdrill oil 4L 8099 0201 03
inlet swivel 7/8” X 24 (CP 4123/CP 4125/CP 4132) 9246 0203 70
inlet swivel 3/8” NPT (CP 4130/CP 4131) 9246 0203 71
inlet swivel - 1/2” pipe - rivet busters 9246 0203 72
coupling - 1/2” universal hose end 9246 0204 35
coupling - 3/4” universal hose end 9246 0204 36
coupling - 1” universal hose end 9246 0204 37
coupling - 1/2” universal female 9246 0204 38
coupling - 3/4” universal female 9246 0204 39
coupling - 1” universal female 9246 0204 40
coupling - 1/2” universal male 9246 0204 41
coupling - 3/4” universal male 9246 0204 42
coupling - 1” universal male 9246 0204 43
hose clamp-1/2” 2-bolts 9246 0204 44
hose clamp-3/4” 2-bolts 9246 0204 45
hose clamp-1” 2-bolts 9246 0204 46
universal coupling gasket - 50/bag 9246 0204 82
safety clip 9246 0204 83
spring guard for 1/2” whip hose 9246 0204 84
whip check - hose-to-hose safety cable 9246 0204 85
whip check - hose-to-tool safety cable 9246 0204 86
26
Accessories
27
Portable Compressors
Chicago Pneumatic Portable Compressors
CPS 90
Free air delivery 88 cfm
Working pressure 100 psi
Max unloading pressure 125 psi
Discharge valves (2) x 3/4”
Fuel tank capacity 8.5 gallons
Engine Kubota (Tier 3)
Horsepower 24.4
Number of cylinders 3
Cooling system Water
Overall: Length 116 in
Height 47 in
Width 51.5 in
Weight 1,225 lbs
CPS 90
• Extremely reliable Kubota engine• Fully galvanized canopy• Recessed single point lifting eye• Torsion bar suspension• Heavy duty tires• Folding drawbar• Two 3/4” discharge valves• Removable side panels• 70 dB(a) @ 23 feet• Curbside fuel filling• Filter maintenance indicator
Reliability, easy maintenance and flexibility are the main characteristics of CP Portable Compressors. The range features proven designs with powerful engines from well-known, well-respected brands. With sound attenuated canopies and straightforward control panels, CP Portable Compressors are quiet and easy to use.
Danger: Compressed air should never be supplied as breathing air unless air is properly purified for breathing. Chicago Pneumatic assumes no responsibility or liability related to the purchaser’s/user’s breathing system.The information contained herein is general in nature and is not intended for specific construction, installation or application purposes.
CPS 90 PORTABLE COMPRESSORS
28
Portable Compressors
CPS 185 DD PORTABLE COMPRESSOR
CPS 185 DD
Free air delivery 185 cfm
Working pressure 100 psi
Max unloading pressure 125 psi
Discharge valves (2) x 3/4”
Fuel tank capacity 21 gallons
Engine Deutz (Interim Tier 4)
Horsepower 48
Number of cylinders 3
Cooling system Oil
Overall: Length 125 in
Height 53 in
Width 55.5 in
Weight 1,980 lbs
Danger: Compressed air should never be supplied as breathing air unless air is properly purified for breathing. Chicago Pneumatic assumes no responsibility or liability related to the purchaser’s/user’s breathing system.The information contained herein is general in nature and is not intended for specific construction, installation or application purposes.
The CPS 185 DD portable air compressor features a proven design with serviceability in mind. The wide opening one piece canopy opens fully for excellent service access. An efficient 48 hp Deutz engine is directly coupled to the compressor airend eliminating the need for high speed gears required by most competitors. A simple design and 500 hour maintenance interval provide for many years of reliable service.
Centralized Controls Curbside control panel with protective shutdown for high engine temperature, low oil pressure and high compressor temperature.
CPS 185 DD
• 500 hour service interval• Single point lifting eye• Torsion bar suspension• Heavy duty tires• Folding drawbar• Removable side panels• Fully galvanized enclosure• 48 HP Deutz engine• Curbside fuel filling• Highly efficient direct drive airend
The new CPS 185 PD portable air compressor from Chicago Pneumatic offers many features asked for by the rental industry. The corrosion resistant galvanneal steel canopy will ensure many years of service. A compact, lightweight design with recessed towing lights and a rear bumper provide greater maneuverability and added safety while towing. The CPS 185 PD features a highly efficient, direct-drive airend that provides 185 cfm of compressed air while using only a 49HP engine. The control panel and discharge valves are conveniently located at the rear of the compressor.
CPS 185 PD
Free air delivery 185 cfm
Working pressure 100 psi
Max unloading pressure 125 psi
Discharge valves (2) x 3/4”
Fuel tank capacity 25 gallons
Engine Perkins (Interim Tier 4)
Horsepower 49
Number of cylinders 4
Cooling system Water
Overall: Length 125 in
Height 57 in
Width 60 in
Weight 2,375 lbs
29
CPS 185 PD PORTABLE COMPRESSOR
CPS 185 PD
• Toolbox• Recessed towing lights• Rear bumper• Electric fuel gauge• Low fuel shutdown• Direct drive airend• 49 HP Perkins engine• Galvanneal steel canopy• Torsion bar suspension• Single point lifting eye• Glow plug engine preheat• Wide opening one piece canopy• Protective shutdown system for
high compressor temperature, high engine temperature, low oil pressure, low fuel level
• Folding drawbar with adjustable jackstand and safety chains
Centralized Controls Control panel and discharge valves are conveniently located on the rear of the compressor. The CPS 185 PD control panel includes an hourmeter, discharge pressure gauge, electric fuel gauge, engine preheat actuator and rotary start switch. The control system also provides protective shutdowns for high engine temperature, low oil pressure, high compressor temperature and low fuel level.
CPS 375
• 500 hour service interval• Large tool storage box• Unloaded starting• Torsion bar suspension• Glow plug engine preheat• Recessed towing lights• Dual stage water separator• Fuel level gauge and hour meter• Low fuel shutdown• Single point lifting eye• Galvanneal sheet metal enclosure w/powder coat paint• Full length lockable doors• A-frame drawbar with adjustable pintle eye,
retractable swivel wheel and safety chains
CPS 375 PORTABLE COMPRESSOR
CPS 375
Free air delivery 375 cfm
Working pressure 100 psi
Max unloading pressure 125 psi
Discharge valves (2) x 3/4”
(1) x 11/2”
Fuel tank capacity 38 gallons
Engine Perkins (Tier 3)
Horsepower 111
Number of cylinders 4
Cooling system Water
Overall: Length 145 in
Height 71 in
Width 72 in
Weight 3,860 lbs
The Chicago Pneumatic CPS 375 portable air compressor provides the strength and flexibility required for today’s demanding applications. The sturdy A-frame drawbar, mechanically controlled Perkins engine and 500 hour maintenance intervals assure many years of dependable service. Standard features include road lights, electric fuel gauge, low fuel shutdown and full length lockable doors. A built-in aftercooler, water separator, primary and secondary filter package is available as an option for applications where clean, dry compressed air is critical.
30
Danger: Compressed air should never be supplied as breathing air unless air is properly purified for breathing. Chicago Pneumatic assumes no responsibility or liability related to the purchaser’s/user’s breathing system.The information contained herein is general in nature and is not intended for specific construction, installation or application purposes.
Portable Compressors
CPS 750
Free air delivery 750 cfm
Working pressure 100 psi
Max unloading pressure 125 psi
Discharge valves (2) x 3/4”
(1) x 11/2”
Fuel tank capacity 76 gallons
Engine Caterpillar (Tier-3)
Horsepower 200
Number of cylinders 6
Cooling system Water
Overall: Length 203 in
Height 78 in
Width 78 in
Weight 6,450 lbs
CPS 750 PORTABLE COMPRESSORS
The Chicago Pneumatic CPS 750 portable air compressor features an extremely compact, lightweight, single-axle design. The smaller size 750 cfm compressor with mechanical surge brakes and road lights allows for easier towing and greater maneuverability. This compressor also features centralized fluid drains for ease of maintenance; compressor oil, engine oil and engine coolant all drain to a common point on the rear of the compressor. The CPS 750 uses a highly efficient airend design that only requires a 200 hp Caterpillar engine to produce 750 cfm of air. A built-in aftercooler, water separator, primary and secondary filter package is available as an option for applications where clean, dry compressed air is critical.
CPS 750
• 500 hour service interval• Single axle design• Mechanical surge brakes• Recessed towing lights• Built in thermostatic bypass valve• Low fuel shutdown• Single point lifting eye• Large tool storage box• Rear bumper• Torsion bar suspension• Three stage fuel filters w/ water separator• Automatic engine preheat• Galvanneal sheet metal enclosure
w/ powder coat paint• A-frame drawbar with adjustable pintle eye,
retractable swivel wheel and safety chains• Triple aluminum radiators designed for optimum
compressor efficiency• Centralized fluid drain point for compressor oil,
engine oil and coolant• Protective shutdowns for engine and compressor
31
32
1.5-13HP
Reciprocating Air Compressors
RCP-908H
RCP-2030
RCP-1330G
Features
• Start-Stop Pressure Switch Control • Fully Enclosed Belt Guard • Tank Drains and Discharge Valve
Features
• Engine Slowdown (Pilot Valve) • Engine Oil Protection• Fully Enclosed Belt Guard Tank Drains and Discharge Valve • ASME Tank and Safety Valve
Single Stage Electric Contractor SeriesPart Number HP Model Amps Electrics
V / Ph.cfm
100 psiTank gal.
L x W x Hinches
8090250831 1.5 RCP-1530 14 115 / 1 5.4 2 x 4 46 x 23 x 26
8090250849 2 RCP-2030 19 / 9.5 115 / 230 / 1 6.5 2 x 4 46 x 23 x 26
Two Stage Gasoline Drive
Part Number HP Model Engine cfm100 psi
Tank gal.
L x W x Hinches
8090250631 9 RCP-930G Robin 16.0 30H 45 x 19 x 38
8090250606 10 RCP-1030G Intek 16.0 30H 45 x 19 x 38
8090250607 11 RCP-1130G Honda 18.5 30H 45 x 19 x 45
8090250823 12.75 RCP-1230GK Kohler 18.5 30H 45 x 19 x 45
8090250608 12.75 RCP-1230G Kohler 25.3 30H 45 x 19 x 45
8090250609 13 RCP-1330G Honda 25.3 30H 45 x 19 x 45
Features
• 12 Volt Electric Start and Recoil Start• Start Key / Panel • Oil Monitor • Engine Slowdown (Pilot Valve)• Fully Enclosed Belt Guard • EZ Pull Tank Drain • ASME Tank and Safety Valves • 3/4” Tank Discharge Valve
Two Stage Gasoline Drive Contractor SeriesPart Number HP Model Engine Starter cfm
100 psiTank gal.
L x W x Hinches
8090250872 9 RCP-908R Robin Recoil 18.6 2 x 5 50 x 29 x 37
8090250880 9 RCP-908H Honda Recoil 18.6 2 x 5 50 x 29 x 37
8090250898 12.75 RCP-128-I Kohler Elec & Recoil 25.3 2 x 5 50 x 29 x 37
Single Stage Gasoline Drive Contractor SeriesPart Number HP Model Engine Starter cfm
100 psiTank gal.
L x W x Hinches
8090250856 5.5 RCP-5530 Honda Recoil 12.4 2 x 4 46 x 23 x 26
8090250864 6 RCP-6030 Robin Recoil 12.4 2 x 4 46 x 23 x 26
Aftermarket
CP engine oilsTo maintain the quality of your compressor, use the engine oil that is designed specifically for your compressor engine - GenOil. This genuine oil is a combination of supreme quality oil blended with special additives. The benefits of using GenOil are better corrosion protection and higher oxidation stability which results in longer oil service intervals and optimal engine performance.
CP coolantGenCool is a superior, high-quality coolant based on a new range of organic coolants. It reduces the operating temperature of the engine and has anti-freeze protection up to -40°C. The long-term corrosion protection allows for extended service intervals. GenCool will provide your engine with year-round protection.
CP compressor oilsGenOil is the only approved and tested oil that meets the quality specifications for your compressor. Our compressor oil has been thoroughly tested to give the optimum level of protection, lengthening the components’ life time and keeping your cost of ownership to an absolute minimum. GenOil keeps the heart of your machine operating at peak performance.
Service KitsThere is no better way to protect your investment than to use genuine parts. CP service packs include all required parts for scheduled maintenance, saving you time and money. With the convenient use of our service kits you will extend the life of your compressor, lower your maintenance costs and increase your profitability.
Genuine Parts
Filters
Air Filters
Lubricants
Coolants
ORIGINAL PART
Original Parts fit the best. Only they will guarantee the original performance of your machine.To ensure maximum working efficiency and a long lifetime every part must conform to specific technical standards. With the use of Original Parts you are certain about the quality, lifetime, utilized material and the impact on other components. All these aspects are important to make the right choice for spare parts. Therefore your best choice is an Original Part. Built to perform and designed to protect.
33
Single Stage Electric Contractor SeriesPart Number HP Model Amps Electrics
V / Ph.cfm
100 psiTank gal.
L x W x Hinches
8090250831 1.5 RCP-1530 14 115 / 1 5.4 2 x 4 46 x 23 x 26
8090250849 2 RCP-2030 19 / 9.5 115 / 230 / 1 6.5 2 x 4 46 x 23 x 26
Two Stage Gasoline Drive
Part Number HP Model Engine cfm100 psi
Tank gal.
L x W x Hinches
8090250631 9 RCP-930G Robin 16.0 30H 45 x 19 x 38
8090250606 10 RCP-1030G Intek 16.0 30H 45 x 19 x 38
8090250607 11 RCP-1130G Honda 18.5 30H 45 x 19 x 45
8090250823 12.75 RCP-1230GK Kohler 18.5 30H 45 x 19 x 45
8090250608 12.75 RCP-1230G Kohler 25.3 30H 45 x 19 x 45
8090250609 13 RCP-1330G Honda 25.3 30H 45 x 19 x 45
Red Hawk
Freedom of movement, zero set-up timeFrom the leading supplier of demolition tools comes the Red Hawk gas-powered breaker. Tough and well designed, the Red Hawk is ideal for small jobs or for working in remote locations.
With no compressors, hoses or cables to set up, gas-powered breakers are ideal for smaller jobs. An impressive range of tools make the Red Hawk extremely flexible and the 7/8” and 4 1/4” steels make for rapid penetration of concrete.
A multi-purpose tool With a wide range of tools, you can use the Red Hawk for everything from cut-ting and breaking to driving and compacting. Whether you need to just break a small patch of concrete, or drive a tent stake, you can get the job finished with a gasoline-powered machine in the same amount of time it takes to set up a compressor and hoses.
Use the rugged andversatile Red Hawk to:
• break concrete • cut asphalt • dig• drive posts and fences• drive rods and spikes• tamp and compact soil• tamp ballast/ties
Breaking concrete
Cutting asphalt
Tamping
Digging
34
Gas-Powered Breaker
Low emissions, vibrations and noise level Red Hawk is a modern tool that meets evolving regulations. Equipped with a catalytic converter and newly designed carburetor, the machine meets tough US EPA 1 emission regulations. In addition, a muffler has reduced the noise level from 114 dB to 107 dB, thereby fulfilling the European Noise Emission Directive.
Easy to start With a choke control, carburetor and user-friendly instructions, the Red Hawk is easy to start.
An optional guide roller makes it easier to pull downwards to start the machine when it is placed higher up. Order part number 9234 0009 38.
Easy to transport The Red Hawk weighs in at about
50 pounds. Each comes with its own carrying case which fits easily into
the trunk of your car.
Vibration-dampening handles
35
Engine
Type Power Cooling system Starter system Recommended fuel Oil type Oil mix Fuel capacity Fuel consumption Impact rate185 cc 1-cylinder, 2-stroke
1kW Forced air Recoilstarter
Unleaded Synthetic two-stroke oil
2% 1:50 0.31 US Gal
0.36 US Gal/hr 2600 BPM
Technical dataModel Part Number Weight
(lb)Length
(in)D
(in)Width over handles
(in)Tool shank (in)
Sound level (Acc. to ISO 3744)
Vibration level (Acc. to ISO 8662)
Red Hawk 8318 0900 00 50.5 27.3 11.0 23.0 7/8" - 4 1/4" 107 dB 4.7 m/s2
At Chicago Pneumatic, we maintain a comprehensive range of chisels so that you can select the right tool for the job. Chicago
Pneumatic chisels are among the hardest wearing on the market. A controlled heat treatment process imparts both strength and high wear resistance to deep surface layers while maintain-ing a tough shock resistant central core to resist breakage.The striking face is end-milled. This results in better contact between the piston and the tool, improved transfer of energy, as well as less vibration and wear on both hammer and chisel.
ToolsTool type Working length Tip width Weight Part number
Shank H 22x108 mm (H 7/8 x 4 1/4 in) mm (in.) mm (in.) kg (lb)
1 Tie tamper 390 (15 1/2) 90 (3 1/2) 3.0 (6.5) 3083 3237 00
Tie tamper 460 (18) 90 (3 1/2) 3.2 (7.0) 9245 2823 30
Tie tamper 550 (22) 90 (3 1/2) 3.9 (8.5) 9245 2822 40
2 Moil point 350 (14) 1.4 (3.1) 3083 3228 00
Moil point 480 (19) 2.0 (4.5) 3083 3229 00
3 Wide chisel 240 (9 1/2) 45 (1 3/4) 1.2 (2.7) 3083 3231 00
Wide chisel 340 (13 1/2) 45 (1 3/4) 1.4 (3.1) 3083 3230 00
Wide chisel 380 (15) 75 (3) 2.6 (5.7) 3083 3232 00
Wide chisel 450 (18) 45 (1 3/4) 2.0 (4.5) 3083 4071 00
4 Asphalt cutter 350 (14) 125 (5) 3.0 (6.5) 9245 2812 90
5 Digging chisel 280 (11) 75 (3) 2.7 (6.0) 3083 3233 00
6 Digging spade 330 (13) 120 (4 3/4) 3.6 (8.0) 3083 3234 00
7 Wedge set 29 mm 1.5 (3.3) 9245 2813 81
Wedge set 34 mm 2.1 (4.6) 9245 2813 51
8 Ground rod driver 195 (7 3/4) 42 (1 11/16) 1.2 (2.6) 3083 3241 00
9 Clay spade 350 (14) 125 (5) 3.4 (7.5) 3083 3235 00
10 Wedge chisel 380 (15) 35 (1 3/8) 2.8 (6.2) 3083 3236 00
11 Driver blank 195 (7 3/4) 55 (2 1/8) 2.5 (5.5) 9245 2822 80
12 Shank for pad 185 (7 1/4) 1.3 (2.9) 3083 3238 00
13 Tamping pad, round 175 (7) 7.5 (16.5) 3083 3252 10
14 Tamping pad, square 175 (7) 5.7 (12.5) 3083 3239 00
15 Tamper sq., compl. 190 (7 1/2) 175 (7) 7.0 (15.5) 3083 3240 00
16 Driver pad, round 100 (4) 2.5 (5.5) 9245 2817 90
17 Post hole driver 460 (18) Ø 40 Ø 1 1/2 4.2 (9.2) 9245 2822 31
18 Stake driver (2.5") 64 2 1/2 ID 5.0 11.0 9245 9800 50
19 Shank for 2.5" stake driver 228 9 2.1 4.6 9245 9912 41
2 Moil point
4 Asphalt cutter
1 Tie tamper
3 Wide chisel
6 Digging spade 7 Wedge set
8 Ground rod driver 9 Clay spade
10 Wedge chisel 11 Driver blank
12 Shank for pad 13 Tamping pad, round
14 Tamping pad, square 15 Tamper sq., compl.
17 Post hole driver
19 Shank for stake driver
16 Driver pad, round
18 Stake driver (2.5")Use only authorized parts. Any damage or malfunction caused by the use of unauthorized parts is not covered by Warranty or Product Liability.
AccessoriesDescription Part Number
20 Guide roller 9234 0009 38
21 Carrying harness 9238 2814 10
21 Carrying harness20 Guide roller
36
Redhawk Tools
37
Hand Held Hydraulic Tools
Absolutely. Chicago Pneumatic (CP) supplies a complete line-up – and you won’t believe how convenient, portable and versatile they are, particularly if you travel to a new site every day, do the job in hours and then move on. Take the power source, for instance. Instead of towing a heavy compressor, you have a compact, portable hydraulic power pack.
OK, but do these tools have the power I need? You will be pleasantly surprised. With hydraulic tools you get raw power from the power pack directly into the tool. They not only feel more powerful but they actually outperform other, comparable tools. Take our 16-inch saw. At full throttle, you have all the power of an 18 HP engine in your hand in a tool weighing only 23 pounds.
For building renovation, highway maintenance, utilities and all situations where portability and flexibility can save time and effort, hydraulic tools are the solution. Use them anywhere, independent of electric or pneumatic supply, in all weather conditions.
Bet they cost an arm and a leg!No. In fact, for smaller construction and rental companies, there are major cost advantages. For instance, for the price of one compressor/breaker combination, you can purchase two complete hydraulic power pack/breaker packages.
Hand Held Hydraulic Tools
Are you saying that hydraulic tools can make my job easier?
38
This power pack sure looks portable!
Power packs PAC P9 PAC P13 PAC P18 PAC D10Engine 9 HP, Honda gasoline 13 HP, Honda gasoline 18 HP, B&S Vanguard gasoline 10 HP, Lombardini dieselWeight (incl oil) lb 130 192 243 256Dimensions (LxWxH) in 23.0x20.7x26.8 27.7x23.6x29.3 28.3x27.6x29.3 27.7x23.6x29.3Oil flow gpm 5 5-8 5-10 5Maximum pressure psi 2200 2200 2200 2000Fuel capacity US gal 1.5 1.8 1.9 1HTMA Type I I / II I / II / RR IHose included NO NO NO NOPower on Demand (POD) YES YES NO NOOil control: engine oil YES YES NO NOElectric start NO NO YES YESPart number 1) 1807 0080 26 1807 0110 25 1807 0160 34 1807 0110 27
Exactly. Why tow a large compressor to the site if you don’t need to? The CP hydraulic power pack couldn’t be more convenient. For site-to-site transportation, two people can lift it into a truck. On-site, the CP power pack can easily be wheeled around by one person.
CP hydraulic power packs are available in gasoline, diesel or electrically driven versions, and provide portable power for a long list of applications in the 5-10 gpm/2000-2500 psi range.
How are they to operate?Couldn’t be simpler. The thermostatically controlled oil cooler gives fast warm-up and helps prevent the hydraulic oil from overheating. Correct working temperature is achieved within minutes – even during the winter. The variable flow on/off valve allows for simple tool changes and slow start up. A gauge shows when it’s time to change the filter.
What about fuel consumption?Many of the power packs are equipped with Power On Demand. This system automatically idles the engine when the tool is not being used and speeds it up when the tool is activated. It saves fuel and keeps noise to a minimum.
Power Pack
39
CP hydraulic breakers – a team of real hard-hitters
Pick hammer BRK 25 DShank size Hex in 7/8 x 3 1/4Weight lbs 28Length in 24Oil flow gpm 5Working pressure psi 1000-1300Return line pressure max psi 150Vibration level (ISO 8662-5) m/s2 10.1Impact rate (5 gpm) blows/min 2400HTMA class IPart number 1801 1746 12
Looking for flexibility – or just raw power?Either way, you’ve found it. CP hydraulic breakers range from flexible, lightweight models up to super heavy duty models hitting at 103 foot pounds and delivering an average of 1,276 blows per minute. Whatever the job, large or small, light or heavy, CP has the right tool in its breaker line-up.
Get more done!The slim design of CP hydraulic breakers gives a good line of sight to the working tool point which boosts your produc-tivity. The tools are well balanced, with no external side bolts and protruding machine parts that can come into contact with the operator’s body.
Quick couplings Hoses are fitted with flat face HTMA quick release couplings for fast and easy connections in all work situations. The couplings are designed to help keep hydraulic systems clean on work sites where there are large amounts of dust and dirt.
BRK 25 D A powerful horizontal pick hammerGet a grip on horizontal tasks! With an impact energy of 18 foot pounds at 2,400 blows/min., the BRK 25 D D-handle hammer is the powerful choice for horizontal work in renovation, demolition and structural alteration. The detachable front handle, available as an optional extra, pivots 360° for optimal positioning.
Hammers, Breakers
40
Breakers BRK 40 BRK 40 VR BRK 55 BRK 55 VR BRK 70 BRK 70 VR BRK 95 BRK 95 VR
Weight lbs 41 42 46 47 56 57 71 73
Length in 25 25 27 27 30 30 30 30
Oil flow gpm 5 5 8 1) 8 1) 8 1) 8 1) 8 2) 8 2)
Working pressure psi 1300-1600 1300-1600 1500-1800 1500-1800 1500-1800 1500-1800 1500-1800 1500-1800
Return line pressure max psi 150 150 215 215 215 215 215 215
Vibration level (ISO 8662-5) 3) m/s2 8.3 3.5 11.4 3.3 11.4 3.4 14.2 6.0
Impact rate (5 gpm) blows/min 1600 1600 1450 1450 1270 1270 - -
Impact rate (8 gpm) blows/min - - 2160 2160 1860 1860 1150 1150
Impact rate (10 gpm) blows/min - - - - - - 1500 1500
HTMA class I I II (I) 1) II (I) 1) II (I) 1) II (I) 1) II (RR) 2) II (RR) 2)
Part number 25x108 (1 x 4¼) 1801 3446 11 1801 3446 10 1801 3546 05 1801 3546 04 - - - -
Part number 28x152 (1¼ x 6) - - 1801 3546 83 - 1801 3646 84 1801 3746 75
Part number 28x160 (1⅛ x 6¼) 1801 3446 58 - 1801 3546 63 - 1801 3646 70 1801 3646 69 - -
Part number 32x152 (1¼ x 6) 1801 3446 60 1801 3446 59 1801 3546 65 1801 3546 64 1801 3646 73 1801 3646 72 1801 3746 85 1801 3746 74
Part number 32x160 (1¼ x 6¼) 1801 3446 62 1801 3446 61 1801 3546 68 1801 3546 67 1801 3646 07 1801 3646 06 1801 3746 09 1801 3746 08
1) Can be adjusted to 5 gpm 2) Can be adjusted to 10.5 gpm 3) BRK 40, BRK 55 and BRK 70 measured at 5 gpm/min, BRK 95 measured at 8 gpm/min
BRK 40 Lightweight , multi-purpose breakers The perfect choice for indoor and outdoor renovation and demo lition jobs, BRK 40 breakers have an impact energy of 48 foot pounds at 1,600 blows/min. Brickwork, frozen soil, asphalt, and concrete are no match for these tough, lightweight breakers. Frequently chosen by contractors and rentals, BRK 40 breakers are also effective for tamping and compaction and are used by railroad companies for tie tamping applications.
BRK 55Medium weight, multi-purpose breakers A favorite with rental companies, BRK 55 breakers are the ideal choice for road building and maintenance applications. Whether it’s asphalt, brickwork, frozen soil, or concrete, the BRK 55 gives you reliable performance. Can be used with both 8 gpm and 5 gpm power packs.
BRK 70Heavy-duty, multi-purpose breakers Get the job done, fast! BRK 70 breakers are idealfor heavier jobs in tough materials such as aphalt,frozen soil, and reinforced concrete. They work at a standard flow rate of 8 gpm and at 5 gpm with a simple adjustment.
BRK 95Super heavy-duty breakers Handheld breakers don’t get much more powerful than this. With an impact energy of 103 foot pounds and an impact rate of 1,275 blows/min., in some situations, the BRK 95 can even replace small excavators with breaker attachments. Ideal for breaking heavy asphalt, reinforced concrete and foundations, these powerful machines are the rugged choice for utility construction, street maintenance, repair of water and gas lines and general construction jobs.
Hammers, Breakers
41
CP hydraulic saws and drills – perfect working partners
Cut-off saws SAW 14 SAW 16Weight lb 21.6 23.4Oil flow gpm 5-8 5-10Max oil pressure psi 2500 2500Revolutions rpm 2500-4000 2000-4000Circumferential speed ft/s 151-246 138-279Blade size in 14 16Arbor hole diameter in 1 1Cutting depth when used handheld in 5.2 6.3Cutting depth when mounted in cart in 3.9 4.9HTMA Type I / II I / II / RRPart number 1809 0140 03 1809 0166 13
Core drills COR 5 COR 15Weight lb 18 18Oil flow gpm 5 - 8 5 - 8Length without drill in 16 16Working pressure psi 1160 - 2500 1160 - 2500Revolutions rpm 600 - 900 1500 - 2250Drill diameter in 2 - 8 0.5 - 3Thread female (drive) 1) ½" BSP ½" BSPHTMA Type I / II I / IIPart number 1806 1014 54 1806 1014 55
1) 1/2” BSP male x 1 1⁄4 UNC male drive adaptor included for use of larger diameter core bits.
CP cut-off sawsYou name it, CP cut-off saws will cut itThey may be light and compact, but don’t be fooled. A CP hydraulic cut-off saw with the right blade will cut through concrete, asphalt and steel. With our 16-inch saw at full throttle, you have the raw power of a gasoline powered engine in your hand.
The open cutting face makes the CP cut-off saw easy to use, even under the most demanding conditions. The simple, direct drive configuration reduces maintenance, especially in comparison with belt-driven saws.
A water kit is available to provide a supply of cooling water where needed.
CP core drillsIdeal for working in confined areas Take a CP hydraulic core drill with you when installing drainage, sewer and water pipes, or cable and ventilation ducts where large, deep holes are needed. CP core drills are well suited for drilling concrete, masonry and asphalt materials. They can be operated freehand or mounted in a drill stand.
Hydraulic control of the drill torque helps to reduce kickback when drill bits jam. So you’re in control, even when drilling holes of 8 inches in diameter and above. Due to the compact design of the CP core drill, you can easily drill holes of up to 8 inches freehand.
Water KitDiamond blades and core bits need a constant supply of water to cool, flush away slurry and suppress dust. On re-mote sites where there is no water supply, we recommend the CP water kit, a small pressurized water container.Item number 3371 8090 02.
Cut off saws, core drills
42
It takes more than stones and debris to stop a CP submersible pump!
Water pumps WAP 2 WAP 3Weight lb 22.6 28Dimensions HxW in 10.5x8.5 14.2x11.8Oil flow gpm 4-6 7-10Working pressure psi 1400 2000Max working pressure psi 2300 2500Pump head max ft 82 105Pump flow max gal/min 222 507Discharge in 2" BSP 3" BSPSolid handling up to in 3/8" 2½"HTMA Type I IIPart number 1806 1014 41 1806 1014 42
CP submersible pumpsThese tools are really toughCP hydraulic submersibles are a range of rugged pumps for continuous pumping of water on building sites, in flooded excavations and cellars, and similar situations. Performance is impressive in relation to size and weight. The 2 inch pump handles dirty water containing small stones and debris up to 3/8 inch. The 3 inch CP submersible trash pump can handle rocks of up to 2 1/2 inches in diameter!
Cooled and lubricated by the hydraulic oil, they can be left to run dry without damage.
Hoses ft 23 39Flat face quick couplings dimension ½" ½"HTMA class I / II / RR I / II / RRPart number 3371 8010 87 3371 8010 89
Water pumps, OFD and hoses
Oil flow divider OFD 5 OFD 8Max oil flow rate gpm 15.8 31.0Regulated oil flow rate gpm 5.3 - 6.6 6.6 - 8HTMA Type I IIPart number 1801 1633 19 1801 1643 18
Accessories – for your hydraulic toolsOil flow divider Reduces flow and pressure, allowing you to run tools from hydraulic-powered carriers. Use an extension hose to connect the oil flow divider to the tool.
Extension hoses Add one or two 23 ft. extension hoses and you can use up to 69 ft. of hose without significant drop in pressure. The hoses are fitted with flat-face, quick release couplings.
43
Classification of toolsFlow 5 gpm 8 gpm 10 gpm
HTMA I II RR
EHTMA C D E
Working tools
Working Tools
Chicago Pneumatic Construction Equipment offers a full range of working tools for its hand held equipment.
Flat to flat (North America) Point to Flat (North America)
7/8 x 3 1/4 in 1 x 4 1/4 in 1 1/8 x 6 in 1 1/4 x 6 in
W (in) L (in) Part no. W (in) L (in) Part no. W (in) L (in) Part no. W (in) L (in) Part no.
Moil point 14 3083 4050 00 15 3083 4030 00 14 3083 3267 00 14 3083 3285 00
18 3083 4050 10 18 3083 4030 10 18 3083 4015 10 18 3083 4000 10
24 3083 4050 20 24 3083 4030 20 24 3083 4015 20 24 3083 4000 20
36 3083 4050 30 36 3083 4030 30 36 3083 4015 30 36 3083 4000 30
Narrow chisel 1 14 3083 3303 00 1 1/8 15 3083 3309 00 1 1/4 14 3083 3268 00 1 3/8 14 3083 3286 00
1 18 3083 4051 10 1 1/8 18 3083 4031 10 1 1/4 18 3083 4016 10 1 3/8 18 3083 4001 10
1 24 3083 3304 00 1 1/8 24 3083 4031 20 1 1/4 24 3083 4016 20 1 3/8 24 3083 4001 20
1 36 3083 4051 30 1 1/8 36 3083 4031 30 1 1/4 36 3083 4016 30 1 3/8 36 3083 4001 30
Wide chisel 3 14 3083 3305 00 3 15 3083 3310 00 3 15 3083 3289 00 3 15 3083 3295 00
3 18 3083 4052 10 3 18 3083 4032 00 3 18 3083 4017 00 3 18 3083 4002 00
3 24 3083 4052 20 3 24 3083 4032 10 3 24 3083 4017 10 3 24 3073 4002 10
Wedge chisel 1 3/8 15 3083 4057 00 2 15 3083 3313 00 2 16 3083 3294 00 2 16 3083 3300 00
Digging chisel 3 14 3083 3306 00 3 15 3083 3311 00 3 15 3083 3291 00 3 15 3083 3297 00
Digging spade 4 3/4 13 3083 3307 00 4 3/4 13 3083 3312 00 5 13 3083 3292 00 5 13 3083 3298 00
Asphalt cutter 5 12 3083 4053 00 5 13 3083 4033 00 5 13 3083 3290 00 5 13 3083 3296 00
Clay spade 5 17 3083 3308 00 5 16 3083 4035 00 5 1/2 15 3083 3293 00 5 1/2 15 3083 3299 00
Shaft for pad 8 3083 4058 00 11 3083 4037 00 9 3083 3269 00 9 3083 3287 00
Tamping pad, round 7 3083 3252 10 7 3083 3252 10 7 3083 3301 00 7 3083 3301 00
Tamping pad, square 7 3083 3239 00 7 3083 3239 00 6 3083 3302 00 6 3083 3302 00
Tamping pad, square 8 3083 3197 00 8 3083 3197 00
Driver pad, round 4 9245 2817 90 4 9245 2817 90
44
RX Hydraulic Breakers
Traditional breaker with 4 side bolts and nutsThe decades old traditional hydraulic breaker technology is complex with many parts.
RX hydraulic breakers (RX2 – RX22)With the exception of the RX11, these RX breakers have fewer components. Only two moving parts and no high pressure accumulator mean less chance of failure. No side bolts make them easier to service, maintain and repair since a multi torque wrench isn’t needed.
RX hydraulic breakers (RX25 – RX53)The RX25-RX53 models feature a cutting-edge side bolt system that uses head bolts and insert threads to distribute the thread strain equally.
RX Hydraulic Breakers – RX means R-eliable to the X-treme
Rugged and hard-hittingDon’t be fooled by their attractive, streamlined designed. RX hydraulic breakers are rugged, reliable and built to last. They have all the power you need to get the job done…and more. Attach the matching RX breaker to the carrier of your choice and you can power your way through a job in no time.
Decrease downtime, increase productivityThe innovative design of the RX line of breakers helps decrease downtime and increase productivity. The small-to-medium sized RX models have fewer components. Only two moving parts and no side bolts make them easier to service, maintain and repair. The larger models feature a power control valve to increase productivity. You can set the breaker characteristics according to the application for higher productivity. The larger models also feature a cutting-edge side bolt system that uses head bolts and insert threads to distribute the thread strain equally.
Less noise means less trouble with the neighborhood on the job siteThanks to the RX recoil absorbing concept and the polyurethane insulated breaker box system, RX breakers are among the quietest you can buy and in line with outdoor equipment directive 2000/14/EU.
45
Value-for-money features
Power booster – for maximum performanceThe power booster feature on RX breakers enables you to get higher breaking performance without increasing the hydraulic input in tougher breaking applications. While the impact energy remains constant, the breaker increases the blow frequency, which results in increased percussive performance.
Power Stop function – to protect your investmentThe power stop function reduces blank firing. That protects the breaker and carrier and increases the working life of the components.
Power control valve – to increase productivityRX breakers (from RX25 upwards) are equipped with a power control valve. This feature enables the operator to set the breaker characteristics according to the application – for higher productivity.
High impact, low noiseRX breakers comply with current and future regulations stipulated in the Noise Emission of Outdoor Equipment Directive 2000/14/EC.
No side bolts (RX2 – RX22)The lack of side bolts on the RX2 – RX22, excluding the RX11, makes these breakers more reliable and easier to service and maintain. Opening a breaker for resealing can be done with ordinary hand tools.
Cutting edge side bolts system (RX25 – RX53)The innovative side bolt system uses head bolts and insert threads to distribute the thread strain equally.
Dust wiperThe optional dust wiper, available on the RX14 upwards, helps increase the lifetime of components that can wear. Simple and reliable -- it keeps abrasive dust out and grease in.
CP-Lube – automatic lubricationBreaker models from the RX14 upwards can be equipped with optional automatic lubrication. CP-Lube ensures optimal lubrication of the wear bushings and the working tool and thus avoids unnecessary downtime.
Ventilation port
Highly efficient internal control valve
Double tool retainer bars(RX14 – RX53)
Dust wiper
CP-Lube for optimum lubrication
Hybrid technology (gas/oil)
High performance-to-weight ratio
Smart design with few components
Effective noise and vibration damping
Power booster
Power stop function
Power control valve
4646
Innovative technology; reliable service and support
A respected name for more than 100 yearsSince 1901 the Chicago Pneumatic name has represented high-performance tools and equipment designed for an extensive range of applications. Today, Chicago Pneumatic has a global reach, with local customer centers around the world.
Extensive investments in R&DThe innovative technology, unique design and value-for-money features of the RX hydraulic breaker line are the direct result of our extensive investments in R&D.
Worldwide customer supportBuying an RX breaker is just the beginning. Chicago Pneumatic distributors offer reliable service and support. Genuine spare parts for your RX breaker are available worldwide, with short delivery times.
RX Hydraulic Breakers
4747
Thirteen breakers at your service
Model Service weight Carrier weight class Operating pressure Oil flow rate Blow frequency
Working tool diameter
Sound power level
Part no.
kg lb 1) t lb 2) bar PSI l/min gpm bpm mm in dB(A)
RX2 117 258 1,3-3,0 2,900-6,600 110-130 1,600-1,890 15-35 4-9 560-1700 42 1.65 109 4)/81 5) 8460 0500 38
RX3 166 366 2,1-4,5 4,600-9,900 110-140 1,600-2,030 30-50 8-13 670-1450 52 2.04 111 4)/83 5) 8460 0500 39
RX4 233 514 2,9-6,0 6,400-13,200 110-140 1,600-2,030 35-60 9-16 520-1150 62 2.44 113 4)/85 5) 8460 0500 40
RX6 284 626 4,2-9,0 9,300-19,800 110-140 1,600-2,030 45-75 12-20 530-1150 70 2.75 114 4)/86 5) 8460 0500 41
RX8 380 838 5,2-12,0 11,500-26,500 120-150 1,740-2,180 60-90 16-24 530-1050 80 3.14 115 4)/87 5) 8460 0500 42
RX11 550 1,210 9-15 19,800-33,100 120-150 1,740-2,180 70-100 18-26 590-1100 80 3.14 116 4) 3363 1095 21
RX14 800 1,760 10-17 22,000-37,500 150-170 2,180-2,470 100-120 26-32 650-850 100 3.93 3363 1049 61
RX18 1200 2,650 15-24 33,100-52,900 150-170 2,180-2,470 120-140 32-37 550-720 120 4.72 3363 1052 39
RX22 1500 3,310 17-28 37,500-61,700 150-170 2,180-2,470 140-160 37-42 520-680 135 5.31 3363 1051 01
RX25 1800 3,970 20-33 44,100-72,800 150-170 2,180-2,470 130-180 34-48 400-680 (460-800) 3)
140 5.51 3363 1056 01
RX29 2200 4,850 25-40 55,100-88,200 150-170 2,180-2,470 150-200 40-53 375-600 (400-800) 3)
150 5.90 3363 1058 93
RX45 3000 6,610 29-46 63,900-101,400 160-180 2,320-2,610 210-260 55-69 380-580(400-800)3)
165 6.49 121 4)/91 5) 3363 1053 59
RX53 4200 9,260 40-70 88,200-154,300 160-180 2,320-2,610 250-320 66-85 350-560(400-800)3)
180 7.08 3363 1097 39
RX hydraulic breakers – features at a glance• Hybrid technology (gas/oil)• Innovative design with less components• Effective noise and vibration damping • Highly efficient internal control valve• Power booster• Power stop function• Power control valve (RX 25-53)• Ventilation port*• Dual retainer bars*
Optional extras • CP-lube for optimum grease distribution*• Dust wiper*
* From RX14 upwards
1) Breaker and breaker box with standard adapter plus working tool.2) Weights apply to standard carriers only. Any variances must be approved by Chicago Pneumatic and/or the carrier manufacturer prior to attachment.3) Power Control: The blow frequency and impact energy can be adjusted to better meet the application requirements.4) Sound power level guaranteed.5) Sound pressure level (r=10m). Important: EN ISO 3744 in accordance with directive 2000/14/EC. Full details of measurement are available in the Safety and Operating Instruction of the product.
48
Original parts make your breaker even more effective
RX Hydraulic Breakers
Model Tool type Working length Total length Part no.
RX2
Moil point (conical) 265 mm 10,43 in 425 mm 16,73 in 4211 1050 01
Chisel (cross) 265 mm 10,43 in 425 mm 16,73 in 4211 1050 02
Blunt tool 265 mm 10,43 in 425 mm 16,73 in 4211 1050 03
RX3
Moil point (conical) 320 mm 12,60 in 530 mm 20,87 in 4211 1051 01
Chisel (cross) 320 mm 12,60 in 530 mm 20,87 in 4211 1051 02
Blunt tool 320 mm 12,60 in 530 mm 20,87 in 4211 1051 03
RX4
Moil point (conical) 350 mm 13,78 in 590 mm 23,23 in 4211 1052 01
Chisel (cross) 350 mm 13,78 in 590 mm 23,23 in 4211 1052 02
Blunt tool 350 mm 13,78 in 590 mm 23,23 in 4211 1052 03
RX6
Moil point (conical) 380 mm 14,96 in 665 mm 26,18 in 4211 1053 01
Chisel (cross) 380 mm 14,96 in 665 mm 26,18 in 4211 1053 02
Blunt tool 380 mm 14,96 in 665 mm 26,18 in 4211 1053 03
RX8
Moil point (conical) 415 mm 16,34 in 745 mm 29,33 in 4211 1054 01
Chisel (cross) 415 mm 16,34 in 745 mm 29,33 in 4211 1054 02
Blunt tool 415 mm 16,34 in 745 mm 29,33 in 4211 1054 03
RX11
Moil point (conical) 390 mm 15,35 in 745 mm 29,33 in 4211 1054 01
Chisel (cross) 390 mm 15,35 in 745 mm 29,33 in 4211 1054 02
Blunt tool 390 mm 15,35 in 745 mm 29,33 in 4211 1054 03
RX14
Moil point (conical) 495 mm 19,49 in 895 mm 35,24 in 4211 1055 38
Chisel (cross) 495 mm 19,49 in 895 mm 35,24 in 4211 1055 39
Blunt tool 495 mm 19,49 in 895 mm 35,24 in 4211 1055 36
RX18
Moil point (conical) 540 mm 21,26 in 995 mm 39,17 in 4211 1055 33
Chisel (cross) 540 mm 21,26 in 995 mm 39,17 in 4211 1055 34
Blunt tool 540 mm 21,26 in 995 mm 39,17 in 4211 1055 31
RX22
Moil point (conical) 565 mm 22,24 in 1050 mm 41,34 in 4211 1055 27
Chisel (cross) 565 mm 22,24 in 1050 mm 41,34 in 4211 1055 28
Blunt tool 565 mm 22,24 in 1050 mm 41,34 in 4211 1055 25
RX25
Moil point (conical) 585 mm 23,03 in 1115 mm 43,90 in 4211 1055 03
Chisel (cross) 585 mm 23,03 in 1115 mm 43,90 in 4211 1055 04
Blunt tool 585 mm 23,03 in 1115 mm 43,90 in 4211 1055 01
RX29
Moil point (conical) 590 mm 23,23 in 1225 mm 48,23 in 4211 1055 09
Chisel (cross) 590 mm 23,23 in 1225 mm 48,23 in 4211 1055 10
Blunt tool 590 mm 23,23 in 1225 mm 48,23 in 4211 1055 07
RX45
Moil point (conical) 670 mm 26,38 in 1365 mm 53,74 in 4211 1055 15
Chisel (cross) 670 mm 26,38 in 1365 mm 53,74 in 4211 1055 16
Blunt tool 670 mm 26,38 in 1365 mm 53,74 in 4211 1055 13
RX53
Moil point (conical) 735 mm 28,94 in 1500 mm 59,06 in 4211 1055 21
Chisel (cross) 735 mm 28,94 in 1500 mm 59,06 in 4211 1055 22
Blunt tool 735 mm 28,94 in 1500 mm 59,06 in 4211 1055 19
Working toolsPoor quality tools can prove to be expensive. Pieces of low grade metal can shear off, enter the hydraulic system and cause serious damage to the breaker and carrier.
Chicago Pneumatic tools are manufactured to the highest quality standards in a fully controlled process. All tools are made from a nickel-chrome alloy that has been optimized for breaking applications. Each tool is precision formed and temper hardened for greater wear resistance.
Description Size Part no.
Chisel paste cartridge (for CP-Lube) 30 x 500 g 3363 0949 10
Chisel paste
Moil point
Chisel
Blunt tool
Asphalt cutter
Wide chisel
49
Carrier classes
ton
(lb)
1 4 7 10 13 16 19 22 25 28 31 34 37 40 43 46 49 52 55 58 61 64 67 70
(2,2
00)
(8,8
00)
(15,
400)
(22,
000)
(28,
600)
(35,
300)
(41,
900)
(48,
500)
(55,
100)
(61,
700)
(68,
300)
(75,
000)
(81,
500)
(88,
200)
(94,
300)
(101
,400
)(1
08,0
00)
(114
,600
)(1
21,2
00)
(127
,800
)(1
34,5
00)
(141
,000
)(1
47,7
00)
(154
,300
)
200
400
550
750
1,000
1,200
2,000
2,500
3,500
4,500
5,000
7,500
10,000
RX2200
ft/lb class
RX3400
ft/lb class
RX4550
ft/lb class
RX6750
ft/lb class
RX81,000
ft/lb class
RX111,200
ft/lb class-
RX142,000
ft/lb class
RX182,500
ft/lb class-
RX223,500
ft/lb class
RX254,500
ft/lb class
RX295,000
ft/lb class
RX457,500
ft/lb class
RX5310,000
ft/lb class
Generators
50
CPG 25- CPG 120
Model CPG 25 CPG 45 CPG 70 CPG 90 CPG 120
Rated Standby Power 22kW/28kVA 39 kW / 50 kVA 67 kW / 84 kVA 80 kW / 100 kVA 106 kW / 133 kVA
Rated Prime Power 20 kW / 25 kVA 35 kW / 45 kVA 56 kW / 70 kVA 72 kW / 90 kVA 95 kW / 120 kVA
Voltage Selections - 3Ø 208 / 240 / 480 208 / 240 / 480 208 / 240 / 480 208 / 240 / 480 208 / 240 / 480
Voltage Selections - 1Ø 120 / 240 120 / 240 120 / 240 120 / 240 120 / 240
Amperage Capacity @ 120 volts 1Ø 2 x 72 amps 2 x 116 amps TBD 2 x 250 amps 2 x 333 amps
Amperage Capacity @ 240 volts 1Ø 72 amps 116 amps TBD 250 amps 333 amps
Amperage Capacity @ 208 volts 3Ø 69 amps 116 amps TBD 250 amps 330 amps
Amperage Capacity @ 240 volts 3Ø 60 amps 100 amps TBD 216 amps 288 amps
Amperage Capacity @ 480 volts 3Ø 30 amps 50 amps TBD 108 amps 144 amps
Sound Pressure Level @ 23 feet @ 75% load 65 dB(A) 68 dB(A) 67 dB(A) 67 dB(A) 67 dB(A)
Fuel Tank Capacity 30 gal. 70 gal. 160 gal. 160 gal. 160 gal.
Fuel Consumption At 75% Load 1.04 gl/hr 1.9 gl/hr TBD 4.9 gl/hr 5.9 gl/hr
Fuel Autonomy At 75% Load 29 hr 36 hr TBD 32.6 hr 27.1 hr
Engine Kubota Kubota John Deere John Deere John Deere
Model Kubota2403 V3600T 4045HF285 4045HF285 4045HF285
Rated Speed 1800 rpm 1800 rpm 1800 rpm 1800 rpm 1800 rpm
Emission Compliance EPA Interim Tier 4 EPA Interim Tier 4 EPA Tier III EPA Tier III EPA Tier III
Rated Output 29.6 HP @ 1800 rpm 49 HP @ 1800 rpm 99 HP @ 1800 rpm 126 HP @ 1800 rpm 158 HP @ 1800 rpm
Coolant Water / Glycol Water / Glycol Water / Glycol Water / Glycol Water / Glycol
Cylinders 4 4 4 4 4
Displacement 2.4 L 3.6 L 4.5 L 4.5 L 4.5 L
Engine Control Electronic Mechanical Electronic Electronic Electronic
Alternator Leroy Somer Stamford Stamford Stamford Stamford
Model LSA40M5 BCI184-H TBD UCI 224 G1 UCI 274 C1
Degree of Protection / Insulation Class IP23 / H IP23 / H IP23 / H IP23 / H IP23 / H
Dimensions Skid (L x W x H) 70 x 33.5 x 46.4 in 82.7 x 37.5 x 53 in 112 x 44 x 67 in 112 x 44 x 67 in 112 x 44 x 67 in
Weight - Skid Wet 1,868 lbs 2,410 lbs 5,310 lbs 5,310 lbs 5,360 lbs
Dimensions w/Trailer (L x W x H) 110 x 59 x 57 in 136.2 x 62.6 x 80.1 in 176 x 78 x 80 in 176 x 78 x 80 in 176 x 78 x 80 in
Weight - w/Trailer Wet 2,121 lbs 3,162 lbs 6,560 lbs 6,560 lbs 6,610 lbs
Convenience Receptacles
20 amp - 125 volt GFCI duplex 2 2 2 2 2
50 amp - 125 / 250 volt twist lock 2 2 2 2 2
Reliability, versatility and rugged design are the main characteristics of CPG Generators. The range features proven designs with powerful engines from well-known, well-respected brands. With Zincor steel coated canopies and 500 hour service intervals. Chicago Pneumatic generators can power a wide variety of critical applications even in the most demanding weather conditions.
Generators
51
Standard Features
• Multi-Voltage Selector Switch • Remote Start / Stop • Digital Control System • 110% Fluid Containment • Electronic Governor
Optional Features
• Skid-Mount• Battery Charger• Ball Coupling• Spare Tire• Tool Box• External Fuel Connections• Coolant Heater
Health, Safety and Environment
Chicago Pneumatic’s stringent manufacturing standards follow ISO 9001 quality assurance regulations. All components are produced and tested to exacting standards for optimum performance in the most demanding conditions.
CPG 45The CPG 45 portable generator from Chicago Pneumatic provides quieter operation, reduced emissions, and loweracquisition and operating costs. Applying insights gained from industrial customers, rental companies, public utilities, and otherend users, Chicago Pnuematic engineers designed the CPG 45 with the most desirable features and capabilities: Standard Features
• Multi-Voltage Selector Switch • Remote Start / Stop • Digital Control System • 110% Fluid Containment
Optional Features
• Skid-Mount• Battery Charger• Electronic Governor • Coolant Heater • Ball Coupling• Spare Tire• Rear Stabilizer Jacks• Tool Box• External Fuel Connections
• Diesel power from the reliable Kubota engine• Electrical power from Stamford BCI series alternator• Selectable 3-phase and 1-phase voltages• 24 hour run-time fuel capacity inside the base frame• 14 gauge galvanneal steel canopy for high durability• Spillage free frame for environmental protection• 120V single phase on the duplex in any voltage condition
CPG 120 (60 Hz)
Model CPG 25 CPG 45 CPG 70 CPG 90 CPG 120
Rated Standby Power 22kW/28kVA 39 kW / 50 kVA 67 kW / 84 kVA 80 kW / 100 kVA 106 kW / 133 kVA
Rated Prime Power 20 kW / 25 kVA 35 kW / 45 kVA 56 kW / 70 kVA 72 kW / 90 kVA 95 kW / 120 kVA
Voltage Selections - 3Ø 208 / 240 / 480 208 / 240 / 480 208 / 240 / 480 208 / 240 / 480 208 / 240 / 480
Voltage Selections - 1Ø 120 / 240 120 / 240 120 / 240 120 / 240 120 / 240
Amperage Capacity @ 120 volts 1Ø 2 x 72 amps 2 x 116 amps TBD 2 x 250 amps 2 x 333 amps
Amperage Capacity @ 240 volts 1Ø 72 amps 116 amps TBD 250 amps 333 amps
Amperage Capacity @ 208 volts 3Ø 69 amps 116 amps TBD 250 amps 330 amps
Amperage Capacity @ 240 volts 3Ø 60 amps 100 amps TBD 216 amps 288 amps
Amperage Capacity @ 480 volts 3Ø 30 amps 50 amps TBD 108 amps 144 amps
Sound Pressure Level @ 23 feet @ 75% load 65 dB(A) 68 dB(A) 67 dB(A) 67 dB(A) 67 dB(A)
Fuel Tank Capacity 30 gal. 70 gal. 160 gal. 160 gal. 160 gal.
Fuel Consumption At 75% Load 1.04 gl/hr 1.9 gl/hr TBD 4.9 gl/hr 5.9 gl/hr
Fuel Autonomy At 75% Load 29 hr 36 hr TBD 32.6 hr 27.1 hr
Engine Kubota Kubota John Deere John Deere John Deere
Model Kubota2403 V3600T 4045HF285 4045HF285 4045HF285
Rated Speed 1800 rpm 1800 rpm 1800 rpm 1800 rpm 1800 rpm
Emission Compliance EPA Interim Tier 4 EPA Interim Tier 4 EPA Tier III EPA Tier III EPA Tier III
Rated Output 29.6 HP @ 1800 rpm 49 HP @ 1800 rpm 99 HP @ 1800 rpm 126 HP @ 1800 rpm 158 HP @ 1800 rpm
Coolant Water / Glycol Water / Glycol Water / Glycol Water / Glycol Water / Glycol
Cylinders 4 4 4 4 4
Displacement 2.4 L 3.6 L 4.5 L 4.5 L 4.5 L
Engine Control Electronic Mechanical Electronic Electronic Electronic
Alternator Leroy Somer Stamford Stamford Stamford Stamford
Model LSA40M5 BCI184-H TBD UCI 224 G1 UCI 274 C1
Degree of Protection / Insulation Class IP23 / H IP23 / H IP23 / H IP23 / H IP23 / H
Dimensions Skid (L x W x H) 70 x 33.5 x 46.4 in 82.7 x 37.5 x 53 in 112 x 44 x 67 in 112 x 44 x 67 in 112 x 44 x 67 in
Weight - Skid Wet 1,868 lbs 2,410 lbs 5,310 lbs 5,310 lbs 5,360 lbs
Dimensions w/Trailer (L x W x H) 110 x 59 x 57 in 136.2 x 62.6 x 80.1 in 176 x 78 x 80 in 176 x 78 x 80 in 176 x 78 x 80 in
Weight - w/Trailer Wet 2,121 lbs 3,162 lbs 6,560 lbs 6,560 lbs 6,610 lbs
Convenience Receptacles
20 amp - 125 volt GFCI duplex 2 2 2 2 2
50 amp - 125 / 250 volt twist lock 2 2 2 2 2
More than 100 years of experienceChicago Pneumatic Tool Company has been designing, manufacturing and selling pneumatic tools since 1901. Today we offer a wide range of products including pneumatic and hydraulic breakers, clay diggers, picks and busters, scabblers, rock drills, rotary and chipping hammers, sump and sludge pumps, and a whole lot more. Having started up in the city that shares our name, today Chicago Pneumatic is a global company, with sales organizations around the world.
www.cp.com
Chicago Pneumatic Construction Equipment 3700 East 68th Avenue Commerce City, CO 80022 USA Tel: (800) 760-4049 Fax: (303) 288-8828
© 2
011
Atla
s Cop
co C
onst
ruct
ion
Min
ing
Tech
niqu
e U
SA L
LC.
9245
999
8 12
c
2/11
5,
000
www.cp.com
Over 100 years of experienceSince 1901 the name Chicago Pneumatic has stood for innovative, high-performance power tools. Today a wide range of pneumatic and hydraulic construction tools, including breakers, clay diggers, picks and busters, scabblers, rock drills, rotary and chipping hammers, sump and sludge pumps, and a whole lot more, are available through a worldwide sales organization.
For more detailed information, please contact:
3392
519
5 93
C
opyr
ight
200
8, C
hica
go P
neum
atic
Con
stru
ctio
n To
ols
Sub
ject
to te
chni
cal m
odifi
catio
ns.
2500
12/
08
a
Flat to flat (North America) Point to Flat (North America)7/8 x 3 1/4 in 1 x 4 1/4 in 1 1/8 x 6 in 1 1/4 x 6 in
W (in) L (in) Part no. W (in) L (in) Part no. W (in) L (in) Part no. W (in) L (in) Part no.Moil point 14 3083 4050 00 15 3083 4030 00 14 3083 3267 00 14 3083 3285 00
18 3083 4050 10 18 3083 4030 10 18 3083 4015 10 18 3083 4000 1024 3083 4050 20 24 3083 4030 20 24 3083 4015 20 24 3083 4000 2036 3083 4050 30 36 3083 4030 30 36 3083 4015 30 36 3083 4000 30
Narrow chisel 1 14 3083 3303 00 1 1/8 15 3083 3309 00 1 1/4 14 3083 3268 00 1 3/8 14 3083 3286 001 18 3083 4051 10 1 1/8 18 3083 4031 10 1 1/4 18 3083 4016 10 1 3/8 18 3083 4001 101 24 3083 3304 00 1 1/8 24 3083 4031 20 1 1/4 24 3083 4016 20 1 3/8 24 3083 4001 201 36 3083 4051 30 1 1/8 36 3083 4031 30 1 1/4 36 3083 4016 30 1 3/8 36 3083 4001 30
Wide chisel 3 14 3083 3305 00 3 15 3083 3310 00 3 15 3083 3289 00 3 15 3083 3295 003 18 3083 4052 10 3 18 3083 4032 00 3 18 3083 4017 00 3 18 3083 4002 003 24 3083 4052 20 3 24 3083 4032 10 3 24 3083 4017 10 3 24 3073 4002 10
Wedge chisel 1 3/8 15 3083 4057 00 2 15 3083 3313 00 2 16 3083 3294 00 2 16 3083 3300 00Digging chisel 3 14 3083 3306 00 3 15 3083 3311 00 3 15 3083 3291 00 3 15 3083 3297 00Digging spade 4 3/4 13 3083 3307 00 4 3/4 13 3083 3312 00 5 13 3083 3292 00 5 13 3083 3298 00Asphalt cutter 5 12 3083 4053 00 5 13 3083 4033 00 5 13 3083 3290 00 5 13 3083 3296 00Clay spade 5 17 3083 3308 00 5 16 3083 4035 00 5 1/2 15 3083 3293 00 5 1/2 15 3083 3299 00Shaft for pad 8 3083 4058 00 11 3083 4037 00 9 3083 3269 00 9 3083 3287 00Tamping pad, round 7 3083 3252 10 7 3083 3252 10 7 3083 3301 00 7 3083 3301 00Tamping pad, square 7 3083 3239 00 7 3083 3239 00 6 3083 3302 00 6 3083 3302 00Tamping pad, square 8 3083 3197 00 8 3083 3197 00Driver pad, round 4 9245 2817 90 4 9245 2817 90
Working tools
Classification of toolsFlow 5 gpm 8 gpm 10 gpmHTMA I II RREHTMA C D E