power of wind
Post on 12-Sep-2014
830 views
DESCRIPTION
Wind turbine design is the process to extract energy from the wind.m.m.palitha mahinda munasinghe,Sri LankaTRANSCRIPT
2
• Harness and plentiful energy source
• It is green, renewable energy and doesn't release any harmful pollutants• It is free, wind farms need no fuel
• The land beneath can usually still be used for farming
• A good method of supplying energy to remote areas
The Benefits Of Wind Power Energy
4/06/2011 mmpmm
3
• The wind is not always some days have no wind
• Suitable areas for wind farms are near the cost, where land is expensive
• Can kill migrating birds flocks tend to like strong winds
• Can affect television & Radio transmission signals
• Can be noisy day and night
Difficulties' of Generate Wind Power Energy
4/06/2011 mmpmm
4
Wind Tower Components
4/06/2011 mmpmm
5
Energy Transfers
Wind turbines convert the kinetic energy from the wind into mechanical energy
which is then used to drive a generator that converts this energy in to electricity
4/06/2011 mmpmm
64/06/2011 mmpmm
Generated power is transferred through conductive wires directly to a home, grid connection system for wider spread use or a battery storage system
Battery banks store the power for later usage and employ a regulator to avoid overcharging incidents
74/06/2011 mmpmm
Horizontal-axis wind turbines (HAWT)
• The main rotor shaft and electrical generator at the top of a tower• Must be pointed into the wind• Small turbines are pointed by a simple wind vane• Large turbines generally use a wind sensor coupled with a servo motor• Most have a gearbox( which turns the slow rotation of the blades into a quicker rotation that is more suitable to drive an electrical generator)
Vertical-axis wind turbines (or VAWTs)
• The main rotor shaft arranged vertically• Turbine does not need to be pointed into the wind • On sites where the wind direction is highly variable is most suitable• The generator and gearbox can be placed near the ground• It could direct drive from the rotor assembly to the ground-based gearbox (hence improving accessibility for maintenance)
Type of wind Turbines
84/06/2011 mmpmm
The rotor component
Includes the blades for converting wind energy to low speed rotational energy. Which is approximately 20% of the wind turbine cost
The generator component
Includes the electrical generator, the control electronics, and most likely a gearbox (e.g. planetary gearbox, adjustable-speed drive or continuously variable transmission) component for converting the low speed incoming rotation to high speed rotation suitable for generating electricity. Which is approximately 34% of the wind turbine cost
The structural support component
Includes the tower and rotor yaw mechanism. Which is approximately 15% of the wind turbine cost
Turbine Design
94/06/2011 mmpmm
Vertical axis wind turbine designs could immediately convert wind into a rotation
This means that they are actually turning more consistently than most of the horizontal axis designs and provide a more consistent output of power
Horizontal-axis wind turbinesVS
Vertical-axis wind turbines
104/06/2011 mmpmm
Turbine Design
Designed and validated should be according to IEC 61400 standards Typical operating temperature range is -20 to 40 °C Designed for a maximum wind speed The survival speed of wind turbines is in the range of 40 m/s to 72 m/s
Horizontal axis wind turbines
114/06/2011 mmpmm
Blades Designs
• The ratio between the speed of the blade tips and the speed of the wind is called tip speed ratio
• High efficiency 3-blade-turbines have tip speed/wind speed ratios of 6 to 7.
• Modern wind turbines are designed to spin at varying speeds
• Use of aluminum and composite materials in their blades has contributed to low rotational inertia
• Newer wind turbines can accelerate quickly if the winds pick up
• It keeping the tip speed ratio more nearly constant
12
Aluminum and composite materials to build blades has contributed to low rotational inertia
Fiberglass-reinforced epoxy material
Most horizontal wind turbines settled on a 3-blade design, which gives the best balance of stability and rotor speed
Blades Designs
4/06/2011 mmpmm
134/06/2011 mmpmm
Blades Designs
144/06/2011 mmpmm
• In simple designs the blades are directly bolted to the hub• More sophisticated designs, they are bolted to the pitch mechanism • Which adjusts their angle of attack according to the wind speed to control their rotational speed• The pitch mechanism is itself bolted to the hub• The hub is fixed to the rotor shaft which drives the generator through a gearbox
The hubPitch mechanism drive turbine
154/06/2011 mmpmm
1. Control panel2. Nacelle3. Generator stator4. Generator rotor5. Blade root6. Pitch drive7. Nose cone8. Main hub9. Tower10. Yaw drive
Direct drive turbine The hub
• Direct drive wind turbines are constructed without a gearbox• Its’ rotor shaft is attached directly to the generator (which spins at the same speed as the blades)
164/06/2011 mmpmm
Tower DesignLattice Tower
It is often called a self-supporting tower. Lattice towers are generally made out of steel and offer the most stability of the tower types. A lattice tower can be found in either a square or a triangular shape. The lattice towers offer the most flexibility of all of the tower types.
Monopole Tower
A monopole tower features a single tubular mast. Because of their instability, a monopole typically does not exceed 200 feet high. However, these towers require the least amount of space on the ground.
Guyed Tower
Guyed towers are similar to a monopole tower in that they consist of a single tubular mast. However, a guyed tower utilizes guy wires to help with stability. These guy wires require a larger piece of land for the tower to rest on. This type of tower is often the cheapest to build, especially at heights over 300 feet.
174/06/2011 mmpmm
Inside assemble
184/06/2011 mmpmm
Inside assemble
19
The speed of wind blowing in your locality should be at least 3-5m/s
Wind turbine should be installed in such a place which is away from obstacles
The survival speed of commercial wind turbines is in the range of 40 m/s (144 km/h) to 72 m/s (259 km/h)
The most common survival speed is 60 m/s (216 km/h)
When It Produce Electricity
4/06/2011 mmpmm
204/06/2011 mmpmm
Permanent magnet DC motor
Motor Design
214/06/2011 mmpmm
224/06/2011 mmpmm
Modes of Operation
Below rated wind speed operation
Around rated wind speed operation
Above rated wind speed operation