pipes and fittings › files › content › downloads › ... · pipes and fittings general...

PIPES AND FITTINGSGeneral catalogue with gross prices valid in Europe, excluding Switzerland (excluding VAT)

Engineering support and customised products available on request – vonroll-hydro.world/support

VISION BECOMESREALITYValued customers and business partners

We recognisediscrimination-free access to clean water as a universal human right.

We are committed tonot using more water than can sustainably flow back – Supplying our customers with high-quality water – Feeding used water back into circulation once purified.

We favourrecycled and recyclable materials (ideally with no degradation), which are manufac-tured and transported with as little CO2 and exhaust gas pollution as possible.

We respectthe intergenerational contract by using high-quality and long-lasting products and services, and paying the right price for them.

Water is the foundation of life – this goes without saying. Despite this (or even because of this), we are not prepared to pay the right price for good, clean and safe water, or make investments to allow water to be safely transported using sustainable infrastructure, to retain its quality and to prevent theft and waste.

After decades of engagement with the issue of water, VONROLL HYDRO has developed the ZEROWATERLOSS mission statement. In doing so, we have seen how ZEROWATERLOSS has become a global challenge. Summer 2003 was the first time that even countries in Europe with plenty of water were shown how vulnerable the foundation of our life and our quality of life is. 2018 refreshed the (gladly suppressed) memory. In many places, sinking groundwater levels have been registered for years, and a significant portion of worldwide migration movements could be attributed to the increasing lack of water or conflicts connected to the control of water reserves. In addition to climate change, the key causes of water shortages are population growth, demands on the standard of living, overexploitation and ignorance. Where the Aral Sea still stood until recently, there are now dry boatyards in the desert. In many countries, over 50 % of the water generated in an energy-intensive manner in desalination plants gets lost on the way to the consumer.

The ZEROWATERLOSS mission statement (www.zerowaterloss.world) presents the counter-thesis: Water is a key part of the intergenerational contract. We must build infrastructure today with first-class, long-lasting components. Water quality and water use must be monitored and safeguarded with innovative products and services (HYDROPORT and INFRAPORT as the

foundations of smart cities and smart villages). The components required here for our infrastructure should ideally be manufactu-red regionally. This allows our values, which are reflected, for instance, in labour and environmental protection laws, to feed into our infrastructure. Thanks to short transport distances, CO2 and exhaust gas pollution are minimised at the same time.

Together with you, our customers and business partners, we want to see ZEROWATERLOSS become a reality, with integrated and coordinated products and services worldwide. The new VONROLL HYDRO 2020 full catalogue forms a solid foundation for joint commitment. Our engineering teams are glad to have the chance to support you in planning and implementing large and small infrastructure projects ([email protected] and all your local VONROLL HYDRO consultants).

ZEROWATERLOSS – so that water also remains a safe founda-tion of life for our descendants.

On behalf of the companies of the VONROLL HYDRO Group

Jürg Brand Marta Lozano

President of the Manager Board of Directors ZEROWATERLOSS

1 2 3 4

Further products or services available on request.

TABLE OF CONTENTS

004 Drinking water pipes positive locking

025 Fittings positive locking

108 Fittings Screw socket

011 Drinking water pipes non-positive locking

044 Fittings non-positive locking

134 Fittings transition pieces

019 Wastewater pipes positive locking

063 Fittings flanged

138 Fittings Wastewater

021 Wastewater pipes non-positive locking

084 Fittings Hydrotight

151 Seals

44Subject to change | VONROLL HYDRO's General T&C and General T&C of Sale and Delivery shall apply | vonroll-hydro.world

Further products or services available on request

PIPES

DUKTUS CMC BLS – Drinking water

Version: Positive locking BLS-joint | TYTON seal | 6 m installation lengthStandards: EN 545 | EN 15 542 | Company standardMaterial: Ductile cast iron | Zinc outside coating (200 g/m²) with a finishing layer (cement mortar) | Blast furnace cement lining | EPDM seal

DN Pressure levelbar

Wall-thickness class

Weight / mkg

Part no. Price / m€

80 100 K10 21.2 0106024893 53.50

100 75 K10 25.4 0106024917 53.50

125 63 K10 32.4 0106025085 77.00

150 63 K10 38.5 0106024916 82.60

200 42 K9 50.3 0106024806 98.80

250 40 K9 66.0 0106024811 123.20

300 40 K9 83.5 0106024915 170.10

400 30 K9 120.3 0106025030 243.10

500 30 K9 158.5 0106025210 340.20

600 32 K9 206.0 0106011145 445.60

700 25 K9 261.2 0106017509 657.70

800 16 K9 322.8 0106019059 761.30

900 16 K9 386.0 0106028123 907.10

1000 10 K9 451.7 0106027345 1,082.00

Pressure pipes for higher pressure levels and other customer-specific versions available on request. Distributed in Switzerland and the Principality of Liechtenstein by our sales partner TMH Hagenbucher AG, Friesstrasse

19, 8050 Zurich, Switzerland, Tel. +41 (0) 44 306 4748, [email protected].


Cutting disc for CMC, cutting depth of approx. 3.5 mm 0700903472 268.00



PIPES

DUKTUS ZIPOX+ BLS – Drinking water

Version: Positive locking BLS-joint | TYTON seal | 6 m installation lengthStandards: EN 545 | Company standardMaterial: Ductile cast iron | Zinc-aluminium outside coating (400 g/m²) with a finishing layer (Epoxy resin) | Blast furnace cement lining | EPDM seal

DN Pressure level bar

Wall-thick-ness class

Weight / mkg


80 100 K10 16.1 0106027446 47.20

100 75 K10 20.1 0106027449 47.80

125 63 K10 26.1 0106027451 72.30

150 63 K10 32.0 0106027455 77.90

200 42 K9 41.4 0106027462 91.10

250 40 K9 55.0 0106027474 116.40

300 40 K9 70.8 0106027478 151.90

400 30 K9 104.2 0106027484 218.80

500 30 K9 140.0 0106030342 306.90

600 32 K9 186.4 0106030343 416.50

700 25 K9 235.0 0106030344 577.90

800 16 K9 294.7 0106030345 725.60

900 16 K9 355.2 0106030346 826.50

1000 10 K9 420.7 0106030347 1,004.30

Pressure pipes for higher pressure levels and other customer-specific versions available on request. Distributed in Switzerland and the Principality of Liechtenstein by our sales partner TMH Hagenbucher AG, Fries-

strasse 19, 8050 Zurich, Switzerland Tel. +41 (0) 4430 64748, [email protected].



PIPES

DUKTUS ZIPOX BLS – Drinking water

Version: Positive locking BLS-joint | TYTON seal | 6 m installation lengthStandards: EN 545 | Company standardMaterial: Ductile cast iron | Zinc outside coating (200 g/m²) with a finishing layer (epoxy resin) | Blast furnace cement lining | EPDM seal



Weight / mkg


80 100 K10 16.1 0106026022 47.20

100 75 K10 20.1 0106026023 48.10

125 63 K10 26.1 0106026024 70.00

150 63 K10 32.0 0106026025 76.60

200 42 K9 41.4 0106026026 90.40

250 40 K9 55.0 0106026033 115.60

300 40 K9 70.8 0106026035 151.90

400 30 K9 104.2 0106026341 218.70

500 30 K9 140.0 0106021982 305.80

600 32 K9 186.4 0106026343 406.90

700 25 K9 235.0 0106026344 558.80

800 16 K9 294.7 0106026346 666.40

900 16 K9 355.2 0106028268 792.90

1000 10 K9 420.7 0106028254 947.70

Pressure pipes for higher pressure levels available on request. Distributed in Switzerland and the Principality of Liechtenstein by our sales partner TMH Hagenbucher AG, Fries-




PIPES

VONROLL CEMPUR BLS – Drinking water

Version: Positive locking BLS-joint | TYTON seal | 6 m installation lengthStandards: EN 545 | EN 15 542 | EN 15 655 | Company standardMaterial: Ductile cast iron | Zinc outside coating (200 g/m²) with a finishing layer (cement mortar) | Polyurethane (PUR) lining | EPDM seal



Weight / mkg


80 100 K10 17.5 280972 84.60

100 75 K10 21.3 280973 84.60

125 63 K10 26.7 280974 102.60

150 63 K9 32.6 280975 119.70

200 42 K9 42.5 280976 161.50

250 40 K9 55.9 280977 240.40

300 40 K9 70.7 280978 295.50

400 30 K9 101.9 280988 567.20

500 30 K9 136.9 280989 665.00

600 32 K9 178.0 280990 830.30

700 25 K9 225.1 280991 1,118.20

Pressure pipes for higher pressure levels available on request.

Fig. 2818





Fig. 2818

PIPES

VONROLL ECOPUR BLS – Drinking water

Version: Positive locking BLS-joint | TYTON seal | 6 m installation lengthStandards: EN 545 | EN 15 655 | EN 15 189 | Company standardMaterial: Ductile cast iron | Polyurethane (PUR) outside coating | Polyurethane (PUR) lining | EPDM seal



Weight / mkg


80 100 K10 14.9 280016 77.90

100 75 K10 18.0 280017 77.90

125 63 K10 23.0 280018 96.90

150 63 K9 28.2 280019 118.80

200 42 K9 36.7 280020 165.30

250 40 K9 48.9 280021 231.80

300 40 K9 62.2 280022 291.70

400 30 K9 90.9 280032 468.40

500 30 K9 123.4 280033 548.20

600 32 K9 161.7 280034 686.90

700 25 K9 206.2 280035 923.40

Pressure levels available on request.



PIPES

VONROLL DUCPUR BLS – Drinking water

Version: Positive locking BLS-joint | TYTON seal | 6 m installation lengthStandards: EN 545 | Company standard | EN 15 655Material: Ductile cast iron | Zinc-aluminium outside coating (400 g/m²) with a finishing layer (bitumen) | Polyurethane

(PUR) lining | EPDM seal



Weight / mkg


80 100 K10 14.4 280416 67.50

100 75 K10 17.4 280417 67.50

125 63 K10 22.2 280418 83.60

150 63 K9 27.3 280419 102.60

200 42 K9 35.5 280420 140.60

250 40 K9 47.5 280421 196.70

300 40 K9 60.5 280422 248.90

400 30 K9 88.7 280432 321.10

500 30 K9 120.7 280433 478.80

600 32 K9 158.6 280434 606.10

700 25 K9 202.8 280435 825.60

Pressure pipes for higher pressure levels available on request

Fig. 2818



PIPES

VONROLL ECOCEM BLS – Drinking water

Version: Positive locking BLS-joint | TYTON seal | 6 m installation lengthStandards: EN 545 | Company standard | EN 15 189Material: Ductile cast iron | Polyurethane (PUR) outside coating | Blast furnace cement lining | EPDM seal



Weight / mkg


80 100 K10 16.8 280916 76.00

100 75 K10 20.8 280917 76.00

125 63 K10 27.0 280918 95.00

150 63 K9 33.1 280919 116.90

200 42 K9 42.8 280920 163.40

250 40 K9 56.8 280921 229.90

300 40 K9 72.9 280922 289.80

400 30 K9 107.0 280932 466.50

500 30 K9 143.3 280933 546.30

600 32 K9 190.4 280934 685.00

700 25 K9 239.7 280935 921.50


Fig. 2818



PIPES

DUKTUS CMC TYTON – Drinking water

Version: TYTON socket joint | TYTON seal | 6 m installation lengthStandards: EN 545 | EN 15 542 | Company standardMaterial: Ductile cast iron | Zinc outside coating (200 g/m²) with a finishing layer (cement mortar) | Blast furnace cement lining | EPDM seal

DN Pressure class≙ PFA bar

Weight / mkg


80 C100 20.5 0107818000* 48.40

100 C100 24.9 0107819000* 49.70

125 C64 31.4 0107820000* 62.90

150 C64 35.8 0106025024* 63.90

200 C64 49.8 0107811000* 84.40

250 C50 63.7 0107812000* 111.40

300 C50 81.0 0107813000* 145.80

350 C40 97.7 0107814000* 193.30

400 C40 116.4 0107815000* 196.50

500 C40 158.1 0107816000* 335.90

600 C30 183.3 0101072875 380.10

600 C40 213.8 0101072997* 417.70

700 C30 253.6 0107773000 589.70

800 C30 313.0 0107774000 671.70

900 C30 371.5 0107775000 794.40

1000 C30 432.6 0107776000 950.10

Pressure pipes for higher pressure levels available on request. Distributed in Switzerland and the Principality of Liechtenstein by our sales partner TMH Hagenbucher AG, Friesstrasse

19, 8050 Zurich, Switzerland Tel. +41 (0) 44 306 4748, [email protected].

* Also available as a BRS system (with a frictional locking TYTON-SIT-PLUS seal), see page 155.





PIPES

DUKTUS ZIPOX+ TYTON – Drinking water

Version: TYTON socket joint | TYTON seal | 6 m installation lengthStandards: EN 545 | Company standardMaterial: Ductile cast iron | Zinc-aluminium outside coating (400 g/m²) with a finishing layer (Epoxy resin) | Blast furnace cement lining | EPDM seal


Weight / mkg


80 C50 13.2 0101072685* 32.80

80 C100 15.5 0101072606* 38.50

100 C50 16.4 0101072686* 32.80

100 C100 19.5 0101072620* 39.40

125 C50 20.9 0101072687* 45.90

125 C64 25.1 0101072605* 52.50

150 C50 25.7 0101072591* 47.60

150 C64 29.2 0101072617* 54.80

200 C50 34.8 0101072592* 67.20

200 C64 40.9 0101072604* 75.30

250 C40 45.5 0101072578* 85.20

250 C50 52.7 0101072602* 101.60

300 C40 58.6 0101072579* 108.10

300 C50 68.3 0101072603* 121.30

350 C30 69.4 0106030433 162.20

350 C40 82.7 0101072594* 178.60






PIPES

DUKTUS ZIPOX+ TYTON – Drinking water

Version: TYTON socket joint | TYTON seal | 6 m installation lengthStandards: EN 545 | Company standardMaterial: Ductile cast iron | Zinc-aluminium outside coating (400 g/m²) with a finishing layer (Epoxy resin) | Blast furnace cement lining | EPDM seal


Weight / mkg


400 C30 65.7 0106030435 177.00

400 C40 100.2 0101072595* 185.10

500 C30 117.9 0106030437 262.10

500 C40 139.6 0101072600* 294.90

600 C30 163.7 0106030439 340.70

600 C40 193.7 0101072654* 368.60

700 C25 195.5 0106030441 455.40

700 C30 211.5 0101072588 494.70

800 C25 246.5 0106030443 540.60

800 C30 272.0 0101072589 589.70

900 C25 299.7 0106030445 658.60

900 C30 332.4 0101072590 697.90

1000 C25 358.6 0106030447 810.90

1000 C30 399.3 0101072593 853.40






PIPES

DUKTUS ZIPOX TYTON – Drinking water

Version: TYTON socket joint | TYTON seal | 6 m installation lengthStandards: EN 545 | Company standardMaterial: Ductile cast iron | Zinc outside coating (200 g/m²) with a finishing layer (epoxy resin) | Blast furnace cement lining | EPDM seal


Weight / mkg


80 C100 15.5 0101072641* 37.60

100 C100 19.5 0101072640* 37.60

125 C64 25.1 0101072639* 49.90

150 C64 29.2 0101072638* 52.50

200 C64 40.9 0101072637* 73.80

250 C50 52.7 0101072635* 99.00

300 C50 68.3 0101072636* 118.00

350 C40 82.7 0101072633* 172.00

400 C40 100.2 0101072631* 177.00

500 C40 139.6 0101072629* 281.80

600 C30 163.7 0101072627 337.50

600 C40 193.7 0101072671* 357.00

700 C30 211.5 0101072625 484.90

800 C30 272.0 0101072623 570.00

900 C30 332.4 0101072621 674.90

1000 C30 399.3 0101072615 828.80






PIPES

VONROLL ECOPUR HYDROTIGHT – Drinking water

Version: HYDROTIGHT socket joint | TYTON seal | 6 m installation lengthStandards: EN 545 | EN 15 655 | EN 15 189 | Company standardMaterial: Ductile cast iron | Polyurethane (PUR) outside coating | Polyurethane (PUR) lining | EPDM seal

Fig. 2817 DN Pressure class≙ PFA bar

Weight / mkg


80 C100 14.3 280024 70.80

100 C100 17.3 280025 70.80

125 C64 21.9 280026 89.30

150 C64 27.1 280027 108.30

200 C64 35.3 280028 151.10

250 C50 46.8 280029 212.80

300 C50 60.1 280030 267.00

350 C40 72.9 280031 340.10

400 C40 90.9 280023 425.60

Please discuss the pressure levels with our Technical Support team.




PIPES

VONROLL DUCPUR HYDROTIGHT – Drinking water

Version: HYDROTIGHT socket joint | TYTON seal | 6 m installation lengthStandards: EN 545 | EN 15 655 | Company standardMaterial: Ductile cast iron | Zinc-aluminium outside coating (400 g/m²) with a finishing layer (bitumen) | Polyurethane

(PUR) lining | EPDM seal


Weight / mkg


80 C100 13.7 280424 65.10

100 C100 16.6 280425 65.10

125 C64 21.1 280426 75.10

150 C64 26.2 280427 86.50

200 C64 34.1 280428 121.60

250 C50 45.3 280429 172.90

300 C50 58.4 280430 214.70

350 C40 71.0 280431 277.40

400 C40 88.7 280423 342.00





PIPES

VONROLL ECOCEM HYDROTIGHT – Drinking water

Version: HYDROTIGHT socket joint | TYTON seal | 6 m installation lengthStandards: EN 545 | Company standard | EN 15 189Material: Ductile cast iron | Polyurethane (PUR) outside coating | Blast furnace cement lining | EPDM seal


Weight / mkg


80 C100 16.1 280924 68.90

100 C100 20.0 280925 68.90

125 C64 26.0 280926 87.40

150 C64 32.0 280927 106.40

200 C64 41.3 280928 149.20

250 C50 54.6 280929 210.90

300 C50 70.7 280930 265.10

350 C40 85.5 280931 338.20

400 C40 107.0 280923 423.70

Please discuss the pressure levels with our Technical Support team.




PIPES

VONROLL DUCPUR SCREW SOCKET – Drinking water

Version: Screw-gland socket joint | 6 m installation length | Standard version with electrical bridgingStandards: EN 545 | Company standard | EN 15 655Material: Ductile cast iron | Zinc outside coating (200 g/m²) with a finishing layer (bitumen) | Polyurethane (PUR) lining | EPDM seal



Weight / mkg


80 40 K10 12.9 201493 79.30

100 40 K10 16.2 201497 89.30

125 40 K10 20.3 201501 110.20

150 40 K10 25.5 201504 133.00

200 40 K10 36.3 201507 181.50

250 25 K10 48.5 201510 231.80

300 25 K10 61.5 201513 296.40

VONROLL DUCPUR SCREW SOCKET – Drinking water

Version: Screw-gland socket joint | Short tube | Standard version with electrical bridgingStandards: EN 545 | Company standard | EN 15 655Material: Ductile cast iron | Zinc outside coating (200 g/m²) with a finishing layer (bitumen) | Polyurethane (PUR) lining | DN 40 to DN 65 epoxy resin coating in accordance with EN 14 901 | EPDM seal

Figure 2318 DN Lmm

PFAbar

Weight / mkg

Part no. Price / unit.€

40 525 40 6.8 202391 154.90

50 520 40 8.1 202392 162.50

65 515 40 11.0 202393 190.00

80 1000 40 21.2 205353 272.70

100 1000 40 25.0 205354 275.50

125 1000 40 31.9 205355 319.20

150 1000 40 40.4 205356 359.10

200 1000 40 52.0 205357 559.60

250 1000 25 78.5 205358 731.50

300 1000 25 88.0 205359 1,201.80

Figure 2317

All prices include a set of screws and a seal. Version not electrically bridged on request.Discontinued, only available while stocks last.

All prices include a set of screws and a seal. Version not electrically bridged on request.



PIPES

DUKTUS CMC BLS – Wastewater

Version: Positive locking BLS-joint | TYTON seal | 6 m installation lengthStandards: EN 598 | EN 15 542 | Company standardMaterial: Ductile cast iron | Zinc outside coating (200 g/m²) with a finishing layer (cement mortar) | Aluminous cement lining | NBR seal



Weight / mkg


80 100 K10 21.2 0106025033 53.50

100 75 K10 25.4 0106026359 53.50

125 63 K10 32.4 0106029789 77.00

150 63 K10 38.5 0106022058 82.60

200 42 K9 50.3 0106025842 98.80

250 40 K9 66.0 0106025665 123.20

300 40 K9 83.5 0106025295 170.10

400 30 K9 120.3 0106025165 243.10

500 30 K9 158.5 0106026890 340.20

600 32 K9 206.0 0106013648 445.60

700 25 K9 261.2 0106021780 657.70

800 16 K9 322.8 0106018104 761.30

900 16 K9 386.0 0106028409 907.10

1000 10 K9 451.7 0106030379 1,082.00







PIPES

DUKTUS ZIPOX BLS – Wastewater

Version: Positive locking BLS-joint | TYTON seal | 6 m installation lengthStandards: EN 598 | Company standardMaterial: Ductile cast iron | Zinc outside coating (200 g/m²) with a finishing layer (epoxy resin) | Aluminous cement lining | NBR seal



Weight / mkg


80 100 K10 16.1 0106026172 47.20

100 75 K10 20.1 0106022054 48.10

125 63 K10 26.1 0106025162 70.00

150 63 K10 32.0 0106025163 72.30

200 42 K9 41.4 0106025100 90.40

250 40 K9 55.0 0106025101 115.60

300 40 K9 70.8 0106025164 151.90

400 30 K9 104.2 0106025144 218.70

500 30 K9 140.0 0106025160 305.80

600 32 K9 186.4 0106010915 406.90

700 25 K9 235.0 0106013910 558.80

800 16 K9 294.7 0106014123 666.40

900 16 K9 355.2 0106028125 792.90

1000 10 K9 420.7 0106027370 947.70



VONROLL DUCPUR BLS – Wastewater

Version: Positive locking BLS socket joint | TYTON seal | 6 m installation lengthStandards: EN 598 | Company standard | EN 15 655Material: Ductile cast iron | Zinc-aluminium outside coating (400 g/m²) with a finishing layer (bitumen) | Polyurethane

(PUR) lining | NBR seal

Figure 1818 DN Pressure level bar


Weight / mkg


500 C30 K9 120.7 280808 391.40

600 C32 K9 158.6 280809 490.20

700 C25 K9 202.8 280810 696.40




PIPES

DUKTUS CMC TYTON – Wastewater

Version: TYTON socket joint | TYTON seal | 6 m installation lengthStandards: EN 598 | EN 15 542 | Company standardMaterial: Ductile cast iron | Zinc outside coating (200 g/m²) with a finishing layer (cement mortar) | Aluminous cement lining | NBR seal


Weight / mkg


80 C100 20.5 0106014054* 48.40

100 C100 24.9 0106161031* 49.70

125 C64 31.4 0106013346* 62.90

150 C64 35.8 0106029684* 63.90

200 C64 49.8 0106010579* 84.40

250 C50 63.7 0106004948* 111.40

300 C50 81.0 0106021543* 145.80

350 C40 97.7 0106160756* 193.30

400 C40 116.4 0106011295* 196.50

500 C40 158.1 0106009785* 335.80

600 C30 183.3 0106026889 380.10

600 C40 213.3 0106160099* 417.70

700 C30 253.6 0106159851 589.70

800 C30 313.0 0106013862 671.70

900 C30 371.5 0106014484 794.40

1000 C30 432.6 0106013474 950.10



* Also available with a frictional locking TYTON-SIT-PLUS seal (see page 155).





PIPES

DUKTUS ZIPOX+ TYTON – Wastewater

Version: TYTON socket joint | TYTON seal | 6 m installation lengthStandards: EN 598 | Company standardMaterial: Ductile cast iron | Zinc-aluminium outside coating (400 g/m²) with a finishing layer (Epoxy resin) | Aluminous cement lining | NBR seal


Weight / mkg


80 C50 13.2 0101072755* 32.80

100 C50 16.4 0101072756* 32.80

125 C50 20.9 0101072757* 45.90

150 C50 25.7 0106026596* 47.60

200 C50 34.8 0101072724* 67.20

250 C40 45.5 0101072736* 85.20

300 C40 58.6 0101072737* 108.10

350 C30 69.4 0101072758 162.20

400 C30 65.7 0101072759 177.00

500 C30 117.9 0101072760 262.10

500 C40 139.6 0101072791* 294.90

600 C30 163.7 0101072761 340.70

700 C30 211.5 0101072779 494.70

800 C30 272.0 0101072780 589.70

900 C30 332.4 0101072781 697.90

1000 C30 399.3 0101072782 853.40

Pressure pipes for other pressure levels available on request. Distributed in Switzerland and the Principality of Liechtenstein by our sales partner TMH Hagenbucher AG, Fries-





PIPES

DUKTUS ZIPOX TYTON – Wastewater

Version: TYTON socket joint | TYTON seal | 6 m installation lengthStandards: EN 598 | Company standardMaterial: Ductile cast iron | Zinc outside coating (200 g/m²) with a finishing layer (epoxy resin) | Aluminous cement lining | NBR seal


Weight / mkg


80 C100 15.5 0106010173* 37.60

100 C100 19.5 0106004290* 37.60

125 C64 25.1 0106013209* 49.90

150 C64 29.2 0106015691* 52.50

200 C64 40.9 0106003988* 73.80

250 C50 52.7 0106005052* 99.00

300 C50 68.3 0106012559* 118.00

350 C40 82.7 0106160274* 172.00

400 C40 100.2 0106012567* 177.00

500 C40 139.6 0106012575* 281.80

600 C30 163.7 0106014200 337.50

600 C40 193.7 0106012583* 357.00

700 C30 211.5 0106160290 484.90

800 C30 272.0 0106160764 570.00

900 C30 332.4 0106159738 674.90

1000 C30 399.3 0106013228 828.80







Weight / mkg


100 100 16.6 280800 77.00

125 64 21.1 280801 93.10

150 64 26.2 280802 103.60

200 64 34.1 280803 122.60

250 50 45.3 280804 151.10

300 50 58.4 280805 202.40

350 40 71.0 280806 231.80

400 40 88.7 280807 258.40


PIPES

VONROLL DUCPUR HYDROTIGHT – Wastewater

Version: HYDROTIGHT socket joint | TYTON seal | 6 m installation lengthStandards: EN 598 | Company standard | EN 15 655Material: Ductile cast iron | Zinc-aluminium outside coating (400 g/m²) with a finishing layer (bitumen) | Polyurethane

(PUR) lining | NBR seal

Figure 1817




FITTINGS

DUKTUS EN fitting BLS – Wastewater90° duckfoot bend

Version: Positive locking BLS-joint | Flange joint | TYTON sealStandards: EN 545 | GSK (Quality Assurance Association for Heavy-Duty Corrosion Protection) | Company standard | EN 14 901Material: Ductile cast iron | Epoxy resin coating

DN PNbar

Weight/unitkg

Part no. Price/unit€

80 100 16.0 0106080008 330.60100 100 21.7 0106080010 389.80

DUKTUS ENH fitting BLS90° hydrant duckfoot bend with an outlet

Version: Positive locking BLS-joint | TYTON sealStandards: EN 545 | GSK | Company standard | EN 14 901Material: Ductile cast iron | Epoxy resin coating

DN AG PFAbar

Weight/unitkg


80 1,5" 100 7.3 0106080014 330.6080 2,0" 100 7.3 0106080015 330.60

All prices include a TYTON sealing ring and thrust-resisting ring and exclude flange joint parts.



FITTINGS

DUKTUS flanged socket BLSFlange socket piece

Version: Positive locking BLS-joint | Flange jointStandards: EN 545 | GSK | Company standard | EN 14 901Material: Ductile cast iron | Epoxy resin coating

DN PNbar

Weight/unitkg


80 10/25/40 9.7 0106080020 225.2080 63 15.2 0106080021 360.4080 100 15.2 0106080022 426.00

100 10/16 12.0 0106080023 254.90100 25/40 12.7 0106080024 382.40100 63 16.2 0106080025 426.00100 100 20.0 0106080026 486.80125 10/16 15.6 0106089027 320.70125 25/40 18.2 0106089028 481.10125 63 23.4 0106089029 513.20125 100 26.4 0106080030 536.20150 10/16 20.9 0106089031 388.20150 25/40 22.1 0106089032 582.20150 63 33.0 0106089033 621.10150 100 32.5 0106089034 674.30200 10 28.0 0106089035 551.00200 16 30.6 0106089036 606.10200 25 29.0 0106089037 826.50200 40 33.5 0106080038 921.10200 63 28.0 0106089039 972.00200 100 56.6 0106089040 1,115.10250 10 39.8 0106089041 773.00250 16 45.0 0106089042 850.30250 25 47.0 0106089043 1,159.50250 40 50.0 0106089044 1,236.80250 63 66.2 0106089045 1,317.40250 100 95.0 0106080046 1,396.40300 10 49.5 0106080047 1,095.40300 16 50.0 0106080048 1,204.90300 25 54.0 0106080049 1,643.10300 40 72.3 0106080050 1,752.60300 63 94.0 0106080051 1,848.70




FITTINGS

DUKTUS flanged socket BLSFlange socket piece


DN PNbar

Weight/unitkg


400 10 90.0 0106029175 2.376.60400 16 89.0 0106025099 2.733.20400 25 95.0 0106025947 3.565.00500 10 127.0 0106025096 3.868.40500 16 150.0 0106025097 4.448.70500 25 165.0 0106029177 5.802.60600 10 140.0 0106026119 5.325.70600 16 158.0 0106025457 6.124.50600 25 170.0 0106028346 7.988.50700 10 205.0 0106026968 8.845.40700 16 215.0 0106028247 10,172.20700 25 225.0 0106028691 13,268.10800 10 238.0 0106026943 9,029.60800 16 260.0 0106028192 10,384.00800 25 280.0 0106028237 13,544.40900 10 345.0 0106027669 12,162.80900 16 368.0 0106028537 13,987.30900 25 425.0 0106029178 18,244.20

1000 10 428.0 0106026856 14,926.001000 16 462.0 0106028345 17,165.001000 25 515.0 0106028188 22,389.00




FITTINGS

DUKTUS F fitting BLSSingle-flange fitting with a weld bead


DN PFAbar

Weight/unitkg


80 10/16/25/40 8.7 0106080052 315.80100 10/16 9.8 0106080055 343.80100 25/40 10.9 0106080056 515.60100 63 15.5 0106080057 550.00100 100 17.9 0106080058 590.50125 10/16 14.6 0106080059 422.70150 10/16 19.6 0106080063 453.90150 25 22.2 0106080064 680.90150 40 23.1 0106080075 726.30150 63 32.5 0106080065 753.30150 100 36.0 0106080066 782.90200 10 24.6 0106089067 600.30200 16 29.4 0106089068 660.40200 25 24.5 0106089069 900.50200 40 29.3 0106089070 960.50200 63 51.5 0106089071 990.10200 100 57.5 0106089072 1,046.10250 10 43.5 0106080073 827.30250 16 43.0 0106080074 910.00250 25 48.0 0106070019 1,241.00300 10 46.5 0106080078 1,036.20300 16 46.5 0106080079 1,139.80300 25 62.0 0106080080 1,554.30400 10 74.5 0106070256 1,868.40400 16 79.5 0106070257 2,148.70400 25 84.0 0100020094 2,802.60500 10 92.5 0106070258 3,026.30500 16 108.0 0106028407 3,480.30600 10 190.0 0106026118 3,889.80600 16 220.0 0106028008 4,473.40600 25 230.0 0106028347 5,834.70700 10 251.0 0106027420 8,273.00700 16 275.0 0106028248 9,514.00800 10 305.0 0106024759 9,860.20800 16 335.0 0106027964 11,339.30900 10 279.0 0106028467 14,004.90900 16 280.0 0106031750 16,105.80

1000 10 441.0 0106027419 16,176.001000 16 470.0 0106027514 18,602.50

All prices exclude flange joint parts.



FITTINGS

DUKTUS GDR fitting BLSSmooth pipes with two weld beads

Version: Positive locking BLS-jointStandards: EN 545 | GSK | Company standard | EN 14 901Material: Ductile cast iron | Epoxy resin coating or outside epoxy resin coating and a blast furnace cement lining (DN 250 to DN 500)

DN PFAbar

Installation lengthmm

Weight/unitkg


80 100 400 8.5 0106089083 213.8080 100 800 14.8 0106089084 269.00

100 100 400 9.5 0106089085 263.20100 100 800 16.0 0106080086 296.10125 100 400 11.8 0106089088 320.70125 100 800 20.5 0106080087 338.80150 100 400 15.3 0106089090 386.50150 100 800 27.0 0106080089 457.20200 100 400 21.0 0106080092 523.00200 100 800 21.0 0106080091 444.10250 40 800 54.0 0106029875 891.40300 40 800 63.0 0106029876 1,120.10400 30 800 79.0 0106029877 1,492.10500 30 800 104.0 0106029878 1,897.40



FITTINGS

DUKTUS MMA fitting BLSDouble socket piece BLS with a flanged branch

Version: Positive locking BLS-joint | Branch flange jointStandards: EN 545 | GSK | Company standard | EN 14 901Material: Ductile cast iron | Epoxy resin coating

DN dn PNbar

Weight/unitkg


80 50 10/40 15.2 0106080126 412.8080 80 10/40 16.0 0106080127 412.80

100 50 10/40 24.0 0106080128 455.60100 80 10/40 20.0 0106080129 455.60100 100 10/40 22.3 0106080130 473.70125 80 10/40 25.8 0106080131 559.20125 100 10/40 27.5 0106080132 583.90150 80 10/40 30.6 0106089134 748.40150 100 10/16 33.0 0106089135 748.40150 150 10/16 39.6 0106089137 672.70150 150 40 42.9 0106032503 1,076.30200 80 10/40 45.4 0106089138 1,065.80200 100 10/16 46.8 0106089139 1,069.10200 150 10/16 51.6 0106089141 1,121.70200 200 10 57.4 0106070196 1,213.80200 200 16 57.0 0106089143 1,190.50200 200 40 66.0 0106032504 1,731.60250 80 10/40 62.0 0106089144 1,356.90250 100 10/16 57.5 0106089145 1,365.10250 150 10/16 70.0 0106089146 1,472.00250 200 16 76.0 0106089148 1,552.30300 80 10/40 76.6 0106089151 1,835.50300 100 10/16 81.2 0106089152 1,838.80300 150 10/16 80.0 0106089153 1,855.30300 300 16 111.8 0106089158 2,344.70400 150 10/16 144.0 0106025494 3,824.00400 150 25/40 152.0 0106025241 5,736.00

All prices include TYTON sealing rings and a thrust-resisting ring and exclude flange joint parts.



FITTINGS



DN dn PNbar

Weight/unitkg


400 200 10 169.0 0106028554 4,072.40400 200 16 169.0 0106089163 4,479.60400 200 25 171.0 0106089164 6,108.60400 300 10 170.0 0106028557 4,375.00400 300 16 170.0 0106089166 4,812.50400 400 10 198.0 0106021934 4,827.30400 400 16 203.0 0106026835 5,551.50400 400 25 203.0 0106026836 7,241.00500 200 10 229.0 0106028212 8,437.50500 200 16 229.0 0106089171 9,281.30500 200 25 230.0 0106026065 12,656.30500 300 10 229.0 0106028213 9,490.10500 300 16 229.0 0106089174 10,439.10500 300 25 252.0 0106031620 14,235.20500 400 10 310.0 0106028007 10,131.60500 400 16 315.0 106038087 10,131.60500 400 25 340.0 0106027937 15,197.40500 500 10 315.0 0106025495 10,172.70500 500 16 331.0 0106027032 11,698.70500 500 25 345.0 0106089180 15,259.00500 500 40 372.0 0106026421 16,276.30




FITTINGS



DN dn PNbar

Weight/unitkg


600 150 16 267.0 0106028214 10,189.10600 150 25 278.0 0106028519 15,283.70600 200 10 277.0 0106028215 10,254.90600 200 16 254.0 0106032520 10,245.90600 300 10 267.0 0106028216 11,332.20600 300 16 234.0 0106028713 12,465.50600 300 25 273.0 0106029964 16,998.40600 400 10 286.0 0106028217 12,602.00600 400 16 305.0 0106029728 14,492.30600 400 25 325.0 0106028274 18,903.00600 600 10 393.0 0106026145 13,453.90600 600 16 420.0 0106028131 15,472.00600 600 25 434.0 0106030637 20,180.90800 150 10/16 630.0 0106027429 20,065.80800 200 10 680.0 0106027423 20,065.80800 200 25 655.0 0106028476 30,098.70800 400 10 665.0 0106027424 21,184.20800 400 25 735.0 0106028477 31,776.30800 600 10 698.0 0106027425 21,888.20800 600 16 698.0 0106031860 25.171.40800 800 10 745.0 0106027418 25,328.90900 100 10 650.0 0106028297 24,095.40900 150 10 680.0 0106028301 24,218.80900 200 10 700.0 0106028303 24,506.60900 300 10 740.0 0106028309 25,041.10

1000 100 10 850.0 0106028312 25,978.601000 150 10 720.0 0106028316 26,093.801000 200 10 720.0 0106028318 26,291.101000 300 10 720.0 0106028324 26,521.401000 300 16 720.0 0106028325 29,173.501000 300 25 685.0 0106028326 39,782.10




FITTINGS

DUKTUS MMB fitting BLSDouble socket piece BLS with a 90° branched socket

Version: Positive locking BLS-joint Standards: EN 545 | GSK | Company standard | EN 14 901Material: Ductile cast iron | Epoxy resin coating

DN dn PFAbar

Weight/unitkg


80 80 100 16.9 0106080159 496.70100 80 100 20.2 0106080160 519.70100 100 100 23.2 0106080161 539.50125 80 100 14.1 0106080162 628.30125 100 100 27.2 0106080163 654.60125 125 100 31.3 0106080164 1,134.90150 80 100 32.7 0106080165 773.00150 100 10/100 36.3 0106080166 816.00150 125 10/100 41.0 0106080167 848.00150 150 100 39.8 0106089168 884.90200 80 100 47.6 0106089169 1,069.10200 100 100 46.3 0106089170 1,085.50200 125 10/100 58.0 0106080171 1,180.90200 150 100 54.2 0106089172 1,200.70200 200 100 63.4 0106089173 1,328.90250 80 100 72.0 0106080174250 100 100 62.4 0106089175 1,529.60250 125 100 78.0 0106080176250 150 100 75.0 0106089177 1,669.40250 200 100 77.0 0106089178 1,822.40250 250 100 89.0 0106089179 1,875.00300 80 85 93.0 0106080180300 100 85 82.0 0106089181 2,097.00300 150 85 87.2 0106089182 2,146.40300 200 85 95.8 0106089183 2,171.10300 250 85 109.0 0106089184 2,648.00300 300 85 140.0 0106089185 2,861.80400 400 30 236.0 0106025626 7,648.00500 500 30 415.0 0106026837 12,121.70

All prices include TYTON sealing rings and a thrust-resisting ring .



FITTINGS

DUKTUS MB fitting BLSSocket head end piece BLS with a 90° branched socket

Version: Positive locking BLS-joint Standards: EN 545 | GSK | Company standard | EN 14 901Material: Ductile cast iron | Epoxy resin coating

DN dn PFAbar

Weight/unitkg


400 80 63 179.5 0106080806 5,692.00400 300 63 211.5 0106032587 6,366.30




FITTINGS

DUKTUS HAS fitting BLSHouse connection piece with a 2" IT outlet

Version: Positive locking BLS-joint | Spigot end with a weld beadStandards: EN 545 | GSK | Company standard | EN 14 901Material: Ductile cast iron | Epoxy resin coating

DN PFAbar

Weight/unitkg


80 10/100 10.5 0106080001 372.70100 10/100 14.0 0106080002 372.70125 10/100 18.0 0106080003 464.80150 10/100 23.5 0106080004 605.80200 10/100 35.0 0106080005 874.30250 10/100 53.0 0106080006 966.30300 10 72.0 0106080007 1,495.40




FITTINGS

DUKTUS MK fitting BLSElbow socket BLS

Version: Positive locking BLS-joint | Elbow 11¼° or 22½° or 30° or 45°Standards: EN 545 | GSK | Company standard | EN 14 901Material: Ductile cast iron | Epoxy resin coating

DN Deflection[°]

PFAbar

Weight/unitkg


80 11 100 8.2 0106080098 284.5080 22 100 8.4 0106080099 291.1080 30 100 8.5 0106080100 284.5080 45 100 9.0 0106080101 365.10

100 11 100 11.8 0106080102 312.50100 22 100 12.1 0106080103 322.40100 30 100 12.4 0106080104 368.40100 45 100 12.6 0106080105 452.30125 11 100 15.1 0106080106 398.00125 22 100 15.5 0106080107 435.90125 30 100 15.8 0106080108 506.60125 45 100 16.2 0106080109 496.70150 11 100 21.0 0106089110 495.10150 22 100 21.5 0106089111 605.30150 30 100 22.0 0106089112 707.20150 45 100 25.0 0106089113 789.50200 11 100 32.5 0106089114 746.70200 22 100 35.0 0106089115 995.10200 30 100 36.0 0106089116 855.30200 45 100 39.0 0106089117 1,093.80250 11 100 51.0 0106080118 1,052.60250 22 100 55.0 0106080119 1,103.60250 30 100 55.8 0106080120 1,128.30250 45 100 64.0 0106080121 1,537.80300 11 100 73.0 0106080122 1,513.20300 22 100 80.0 0106080123 1,603.60300 30 100 84.0 0106080124 1,639.80300 45 100 86.0 0106080125 2,105.30400 11 63 129.0 0106080800 3,095.40400 22 63 141.0 0106080801 3,297.70400 30 63 153.0 0106080802 3,371.70500 11 50 207.5 0106080803 6,992.60500 22 50 234.0 0106080804 7,300.20500 30 50 238.0 0106080805 7,336.30




FITTINGS

DUKTUS MMK fitting BLSDouble socket elbow BLS


DN Deflection[°]

PFAbar

Weight/unitkg


80 11° 100 10.4 0106080186 287.8080 22° 100 11.0 0106080187 299.3080 30° 100 10.4 0106080188 312.5080 45° 100 11.4 0106080189 319.10

100 11° 100 14.3 0106080190 327.30100 22° 100 14.6 0106080191 342.10100 30° 100 14.8 0106080192 345.40100 45° 100 14.1 0106080193 358.60125 11° 100 20.2 0106080194 394.70125 22° 100 20.8 0106080195 407.90125 30° 100 21.0 0106080196 419.40125 45° 100 22.0 0106080197 435.90150 11° 100 22.5 0106089198 496.70150 22° 100 23.6 0106089199 523.00150 30° 100 24.3 0106089200 526.30150 45° 100 25.8 0106089201 542.80200 11° 100 36.8 0106089202 731.90200 22° 100 38.6 0106089203 764.80200 30° 100 41.3 0106089204 781.30200 45° 100 41.3 0106089205 809.20250 11° 100 53.0 0106089206 978.60250 22° 100 56.9 0106089207 1,028.00250 30° 100 59.3 0106089208 1,049.30250 45° 100 65.1 0106089209 1,159.50300 11° 100 69.4 0106080210 1,401.30300 22° 100 75.0 0106080211 1,483.60300 30° 100 77.8 0106080212 1,521.40300 45° 100 84.5 0106080213 1,603.60400 11° 30 116.0 0106029190 2,861.80400 22° 30 125.5 0106029191 3,042.80400 30° 30 137.0 0106029192 3,125.00400 45° 30 149.5 0106029193 3,281.30




FITTINGS

DUKTUS MMK fitting BLSDouble socket elbow BLS


DN Deflection[°]

PFAbar

Weight/unitkg


500 11° 30 170.0 0106025095 6,356.90500 22° 30 197.8 0106029152 6,636.50500 30° 30 205.0 0106025362 6,669.40500 45° 30 227.0 0106029150 6,907.90600 11° 32 184.0 0106026120 8,955.60600 22° 32 225.0 0106026121 9,542.80600 30° 32 225.0 0106026122 9,712.20600 45° 32 268.0 0106026141 10,156.30700 11° 25 277.0 0106026969 14,153.00700 22° 25 320.0 0106026970 15,105.30700 30° 25 335.0 0106026971 15,444.10700 45° 25 373.0 0106026972 17,171.10800 11° 25 411.0 0106026946 15,847.00800 22° 25 455.0 0106026947 16,250.00800 30° 25 485.0 0106026949 18,018.10800 45° 25 546.0 0106026950 17,680.90900 11° 25 529.0 0106028146 19,070.70900 22° 25 591.0 0106028147 21,422.70900 30° 25 632.0 0106028148 22,845.40900 45° 25 713.0 0106028149 26,200.70

1000 11° 25 651.0 0106026857 22,105.301000 22° 25 718.0 0106026858 24,942.401000 30° 25 795.0 0106026951 25,493.401000 45° 25 875.0 0106026859 30,567.40




FITTINGS

DUKTUS MMQ fitting BLSDouble socket elbow BLS 90°

Version: Positive locking BLS-joint | 90° elbowStandards: EN 545 | GSK | Company standard | EN 14 901Material: Ductile cast iron | Epoxy resin coating

DN PFAbar

Weight/unitkg


80 100 11.6 0106080214 332.20100 100 15.5 0106080215 394.70125 100 25.5 0106080216 501.60150 100 30.5 0106089217 608.60200 100 53.4 0106089218 937.50250 100 77.0 0106089219 1,324.00300 100 89.0 0106080220 2,047.70400 30 200.5 0106029194 5,238.50




FITTINGS

DUKTUS MMR fitting BLSBLS double socket reduction piece

Version: Positive locking BLS-jointStandards: EN 545 | GSK | Company standard | EN 14 901Material: Ductile cast iron | Epoxy resin coating

DN1 DN2 PFAbar

Weight/unitkg


100 80 100 11.9 0106080221 337.20125 80 100 16.0 0106080222 485.20125 100 100 17.2 0106080223 501.60150 80 100 19.0 0106080224 526.30150 100 100 21.0 0106080225 551.00150 125 100 20.8 0106080226 555.90200 100 100 29.6 0106080227 736.80200 150 100 30.0 0106080228 756.60250 150 100 44.2 0106080229 995.10250 200 100 45.8 0106080230 1,052.60300 150 100 53.0 0106080231 1,340.50300 200 100 59.0 0106080232 1,381.60300 250 100 62.8 0106080233 1,472.00400 300 30 111.8 0106029196 2,985.20500 400 30 160.0 0106080808 7,031.30




FITTINGS

DUKTUS P plug BLSSocket sealing plug BLS with 2" internal thread

Version: Positive locking BLS-joint | outlet with 2" internal threadStandards: EN 545 | GSK | Company standard | EN 14 901Material: Ductile cast iron | Epoxy resin coating

DN PFAbar

Weight/unitkg


80 100 3.6 0106080234 430.90100 100 4.6 0106080235 430.90125 100 6.7 0106080236 501.60150 100 9.0 0106080237 501.60200 100 14.3 0106080238 748.40250 100 27.5 0106080239 1,003.90300 100 49.5 0106080240 1,326.30



FITTINGS

DUKTUS U fitting BLSPush-on sockets

Version: Positive locking and frictional locking BLS-joint | Joint and repair pieceStandards: EN 545 | GSK | Company standard | EN 14 901Material: Ductile cast iron | Epoxy resin coating

DN PFAbar

Weight/unitkg


80 100 12.5 0106080650 475.00100 100 17.0 0106080651 575.70125 100 24.0 0106080652 724.70150 100 30.5 0106080653 830.60200 100 45.5 0106080654 1,184.20250 40 67.0 0106080655 1,641.40300 30 96.0 0106080656 2,228.60400 30 115.0 0100020855 3,856.90500 30 131.0 0100020857 8,297.70




FITTINGS

DUKTUS clamping ring BLS

Version: BLS-joint with a clamping ring (frictional locking), compatible with all BLS sockets DN 80 to DN 500Standards: Company standardMaterial: Ductile cast iron | Galvanised finishing layer

DN PFAbar

Weight/unitkg


80 45 0.9 0701400060 69.10100 45 1.0 0701400061 75.70125 45 1.4 0701400062 82.20150 45 1.7 0701400063 98.70200 45 2.2 0701400064 118.40250 45 2.7 0701400065 139.80300 30 3.6 0701400066 197.40400 30 6.0 0701400067 361.80500 30 7.2 0701400068 477.00



FITTINGS

VONROLL/DUKTUS EN fitting90° duckfoot bend

Version: TYTON socket joint | Flange jointStandards: EN 545 | DIN 28 650 | EN 1092-2 | Company standard | EN 14 901Material: Ductile cast iron | Epoxy resin coating or external bitumen and internal enamel

DN PNbar

Weight/unitkg



80 10/16 13.3 90402172 128.60 90402173 158.30100 10/16 18.5 90401997 140.60 90401998 178.40

EPOXY BITUMEN/ENAMEL

All prices include a TYTON sealing ring and exclude flange joint parts.



FITTINGS

VONROLL/DUKTUS flanged socketFlange socket piece

Version: TYTON socket joint | Flange jointStandards: EN 545 | EN 1092-2 | Company standard | EN 14 901Material: Ductile cast iron | Epoxy resin coating or external bitumen and internal enamel

DN PNbar

Weight/unitkg



80 10/16 7.3 90400879 54.20 90401188 66.80100 10/16 9.0 90402134 60.50 90401225 76.30125 10/16 11.5 90401228 79.40 90401431 100.90150 10/16 14.0 90401231 102.80 90401967 117.90200 10 21.0 90401237 121.10 90401244 162.70200 16 21.0 90403065 135.60 90404703 182.20250 10 29.0 90402242 187.30 90402386 235.80250 16 29.0 90401387 215.00 90411451 260.40300 10 37.0 90401243 250.90 90401274 324.70300 16 37.0 90404719 291.30 90408432 364.40350 10 45.0 90402387 452.10 90406280 564.30350 16 45.0 90408077 518.90 90415706 649.40400 10 56.0 90401248 493.00 90402795 665.20400 16 56.0 90406569 566.80 90402796 769.20500 10 89.0 90402797 1,063.60 90402807 1,614.00500 16 89.0 90406018 1,223.10 90415707 1,807.60600 10 140.0 90402799 1,645.60 90406837 2,127.20600 16 140.0 90405484 1,894.60 90415708 2,382.00700 10 167.0 90406839 2,053.50 90407063 2,532.00700 16 167.0 90409674 2,361.20 90415710 2,948.10800 10 260.0 90405769 2,933.60 90406840 3,852.20800 16 260.0 90408345 3,373.10 90415711 4,429.80

1000 10 355.0 90407851 4,230.50 90410825 5,126.801000 16 355.0 90407854 4,893.20 90415712 5,649.60


All prices include a TYTON sealing ring and exclude flange joint parts.



FITTINGS

VONROLL/DUKTUS F fittingSingle-flange fitting

Version: TYTON socket joint | Flange jointStandards: EN 545 | EN 1092-2 | Company standard | EN 14 901Material: Ductile cast iron | Epoxy resin coating or external bitumen and internal enamel

DN PNbar


Weight/unitkg



50 10/16 4.9 90414357 68.10 90414356 82.6080 10/16 350 8.7 90401257 60.50 90401258 75.00

100 10/16 360 10.5 90402132 75.70 90401261 91.40125 10/16 370 12.5 90402390 98.40 90402800 133.00150 10/16 380 17.0 90401266 103.40 90401267 134.90200 10 400 24.0 90401270 156.40 90401271 219.40200 16 400 24.0 90401375 171.50 90406903 241.50250 10 420 37.0 90402393 230.80 90402454 299.50250 16 420 37.0 90405141 254.10 90413218 336.00300 10 440 42.0 90401204 281.80 90402394 375.10300 16 440 42.0 90402461 331.00 90410325 428.10350 10 460 59.5 90404620 536.50 90406846 696.70350 16 460 59.5 90408607 616.60 90415713 872.00400 10 480 80.0 90401280 626.10 90402802 814.60400 16 480 80.0 90405895 720.00 90410877 924.90500 10 520 115.0 90402395 1,383.90 90404041 1,762.20500 16 520 115.0 90405784 1,592.60 90415714 2,124.10600 10 560 207.0 90402396 1,991.10 90405611 2,731.90600 16 560 207.0 90405485 2,508.10 90415718 3,134.10700 10 600 240.0 90405783 2,619.70 90406847 3,357.90700 16 600 240.0 90412824 2,936.80 90415719 4,016.20800 10 600 330.0 90405768 3,338.40 90406848 4,555.20800 16 600 330.0 90407494 3,839.00 90415720 5,323.20

1000 10 600 525.0 90406849 5,132.10 90406850 5,809.801000 16 600 525.0 90413051 6,069.00 90415721 6,940.60





FITTINGS

VONROLL/DUKTUS MK fittingElbow socket

Version: TYTON socket joint | 11¼° or 22½° elbowStandards: in accordance with company standard | EN 14 901Material: Ductile cast iron | Epoxy resin coating or external bitumen and internal enamel

DN Deflection[°]

PFAbar

Weight/unitkg



80 11 100 8.1 90406547 112.90 90406548 131.10100 11 100 8.2 90406394 91.40 90406404 104.00125 11 64 11.0 90406398 119.80 90406408 137.40150 11 64 14.0 90406527 140.00 90406528 160.80200 11 64 20.0 90406506 230.80 90406507 244.00


DN Deflection[°]

PFAbar

Weight/unitkg



80 22 100 8.1 90406551 112.90 90406552 131.10100 22 100 8.5 90406395 93.30 90406405 107.20125 22 64 12.0 90406399 125.50 90406409 144.40150 22 64 15.0 90406531 164.60 90406532 189.80200 22 64 27.0 90406510 281.20 90406511 322.80

All prices include a TYTON sealing ring.




BITUMEN/ENAMEL

FITTINGS

VONROLL/DUKTUS MK fittingElbow socket

Version: TYTON socket joint | 30° or 45° elbowStandards: in accordance with company standard | EN 14 901Material: Ductile cast iron | Epoxy resin coating or external bitumen and internal enamel

DN Deflection[°]

PFAbar

Weight/unitkg



80 30 100 8.2 90406555 121.10 90406556 140.00100 30 100 12.0 90406396 100.90 90406406 121.10125 30 64 12.5 90406400 143.10 90406410 182.20150 30 64 17.9 90406535 196.10 90406536 225.70200 30 64 29.0 90406514 248.40 90406515 286.20

EPOXY

DN Deflection[°]

PFAbar

Weight/unitkg



80 45 100 8.5 90406559 128.00 90406560 151.90100 45 100 9.0 90406397 122.90 90406407 141.90125 45 64 12.5 90406401 146.90 90406411 179.70150 45 64 18.0 90406539 190.40 90406540 218.80200 45 64 25.5 90406518 304.50 90406519 350.50





FITTINGS

VONROLL/DUKTUS MQ fitting90° elbow socket

Version: TYTON socket joint Standards: in accordance with company standard | EN 14 901Material: Ductile cast iron | Epoxy resin coating or external bitumen and internal enamel

DN PFAbar

Weight/unitkg



80 100 13.2 90406564 224.30 90406563 291.60100 100 13.3 90406402 181.60 90406412 225.70125 64 18.0 90406403 282.50 90406413 352.40150 64 22.4 90406543 322.20 90406544 386.50200 64 37.3 90406522 364.40 90406523 435.70





FITTINGS

VONROLL/DUKTUS MM fittingTYTON coupling

Version: TYTON socket joint Standards: EN 545 | DIN 28 603 | Company standard | EN 14 901Material: Ductile cast iron | Epoxy resin coating or external bitumen and internal enamel

DN Installation length mm

PFAbar

Weight/unitkg



200 170 64 30.0 90407074 248.90 90407081 311.00250 175 50 35.0 90407079 310.80 90407082 388.40300 180 50 45.0 90407080 426.20 90407083 532.80400 185 40 65.0 90407078 736.40 90407084 919.20500 215 40 103.7 90409792 1,421.70 90410826 1,762.20600 340 40 145.0 90410809 1,888.30 90410827 2,392.70


All prices include TYTON sealing rings.



FITTINGS

VONROLL/DUKTUS MMA fittingDouble socket piece with a flanged branch

Version: TYTON socket joint | Branch flange jointStandards: EN 545 | EN 1092-2 | Company standard | EN 14 901Material: Ductile cast iron | Epoxy resin coating or external bitumen and internal enamel

DN1 DN2 PNbar

Weight/unitkg



80 80 10/16 14.5 90400515 129.20 90400554 160.80100 40 10/16 14.5 90400256 116.60 90407085 140.60100 50 10/16 13.3 90400260 124.80 90400261 150.70100 80 10/16 17.0 90400264 112.90 90400263 160.80100 100 10/16 18.0 90400253 119.20 90400250 167.70125 40 10/16 18.3 90400282 193.60 90404990 240.80125 80 10/16 19.3 90400288 207.40 90400287 259.80125 100 10/16 20.4 90400269 207.40 90400270 259.80125 125 10/16 24.5 90400277 233.30 90400276 303.30150 40 10/16 20.5 90400315 204.90 90405585 276.80150 50 10/16 20.6 90400322 231.40 90400321 288.80150 80 10/16 25.5 90400328 184.10 90400329 230.80150 100 10/16 26.4 90400297 192.30 90400293 240.20150 150 10/16 30.9 90400309 206.80 90400308 260.40200 40 10/16 25.5 90400370 286.20 90407092 372.00200 50 10/16 25.5 90405017 286.20 90400372 372.00200 80 10/16 30.0 90400380 240.20 90400376 311.50200 100 10/16 32.5 90400338 254.70 90400337 331.00200 150 10/16 40.0 90400347 288.10 90400346 339.80200 200 10 46.0 90400356 337.30 90400357 438.80200 200 16 46.0 90400582 378.30 90400578 491.80


All prices include TYTON sealing rings and exclude flange joint parts.



FITTINGS



DN1 DN2 PNbar

Weight/unitkg



250 80 10/16 37.9 90400408 308.90 90400407 401.60250 100 10/16 39.7 90400386 343.00 90400385 446.40250 150 10/16 45.0 90400391 371.40 90400390 482.90250 200 10 52.5 90400394 419.90 90407100 546.00250 250 10 60.7 90400403 454.60 90400404 616.60250 200 16 52.5 90405366 477.30 90415818 604.00250 250 16 60.7 90406262 509.40 90415819 636.80300 80 10/16 48.5 90400444 411.10 90400443 552.90300 100 10/16 50.0 90400412 411.10 90400413 552.90300 150 10/16 57.0 90400415 469.70 90400416 609.70300 200 10 66.5 90400423 513.20 90400420 667.70300 250 10 75.5 90400429 617.90 90407101 802.60300 300 10 79.0 90400434 651.90 90400435 848.00300 200 16 66.5 90400424 590.80 90415820 738.30300 250 16 75.5 90406179 710.60 90415821 887.70300 300 16 79.0 90404720 923.70 90415822 1,154.40400 80 10/16 71.3 90400473 776.80 90400470 974.70400 100 10/16 74.6 90403580 785.00 90400447 1,020.80400 150 10/16 85.5 90400452 816.50 90400451 1,062.40400 300 10 114.0 90407198 1,373.80 90400460 1,856.80400 400 10 140.0 90400465 1,424.90 90400466 2,493.60400 300 16 120.0 90406726 1,574.90 90415823 2,134.80400 400 16 145.0 90409917 1,043.40 90415824 2,868.70





FITTINGS



DN1 DN2 PNbar

Weight/unitkg



500 80 10/16 109.0 90403841 1,781.10 90407103 2,224.30500 100 10/16 114.0 90405154 1,781.70 90407104 2,224.30500 150 10/16 129.0 90405153 1,883.30 90407105 2,354.90500 200 10 141.0 90405664 1,883.30 90407050 2,354.90500 250 10 159.0 90407106 2,228.10 90407051 2,585.60500 300 10 163.0 90407107 2,153.10 90407052 2,695.30500 400 10 180.0 90407108 2,337.80 90407053 3,042.10500 500 10 212.0 90407109 2,590.70 90407049 3,105.10500 200 16 141.0 90405152 2,228.10 90415825 2,708.60500 250 16 159.0 90415162 2,375.70 90415826 2,972.70500 300 16 173.0 90409751 2,479.70 90415827 3,100.70500 400 16 195.0 90407944 2,689.60 90415828 3,363.60500 500 16 225.0 90411237 3,662.50 90415829 3,662.50600 80 10/16 162.9 90407110 2,237.60 90407111 2,799.30600 100 10/16 163.6 90406232 2,639.80 90407112 3,431.70600 150 10/16 164.2 90407113 2,666.90 90407199 3,467.00600 200 10 167.1 90407115 2,332.20 90407116 3,023.20600 250 10 176.0 90407118 2,931.10 90407119 3,811.30600 300 10 230.0 90400514 3,062.90 90400553 3,811.30600 400 10 230.0 90407120 3,115.20 90407121 3,968.90600 500 10 342.0 90407122 3,666.30 90407123 4,766.40600 600 10 328.0 90407124 3,666.30 90407125 4,766.40600 200 16 167.1 90407940 2,727.50 90415830 3,407.80600 250 16 176.0 90415163 3,458.20 90415831 4,803.60600 300 16 241.0 90415164 3,457.60 90415832 4,323.20600 400 16 249.0 90410709 3,581.80 90415833 4,504.20600 500 16 342.0 90415165 4,216.70 90415834 5,625.20600 600 16 355.0 90410852 4,326.40 90400556 5,625.20





FITTINGS

VONROLL/DUKTUS MMB fittingDouble socket piece with a branched socket

Version: TYTON socket joint | Branched screw-gland socket joint or TYTON socket jointStandards: EN 545 | Company standard | EN 14 901Material: Ductile cast iron | Epoxy resin coating or external bitumen and internal enamel

DN1 DN2 Version PFAbar

Weight/unitkg



125 40 TYT/SMU 40 15.0 90400635 265.00 90407126 302.80125 80 TYT/TYT 64 16.8 90406234 219.40 90400642 274.30125 100 TYT/TYT 64 19.6 90400631 221.30 90400637 267.30125 125 TYT/TYT 64 20.9 90400633 228.90 90400640 276.20150 40 TYT/SMU 40 18.6 90400782 275.70 90400773 310.40150 80 TYT/TYT 62 19.8 90400783 228.20 90400774 278.70150 100 TYT/TYT 62 20.9 90400780 211.80 90400771 486.10150 150 TYT/TYT 62 25.2 90400781 240.20 90400772 298.20200 40 TYT/SMU 40 25.2 90407137 299.70 90407138 337.50200 80 TYT/TYT 50 28.0 90405003 257.20 90407145 309.60200 100 TYT/TYT 50 29.0 90404993 267.30 90400775 322.80200 125 TYT/TYT 33.0 90408501 297.60 90410413 357.50200 150 TYT/TYT 50 33.0 90400825 303.30 90400776 378.90200 200 TYT/TYT 50 39.5 90400785 310.80 90400806 388.40250 125 TYT/TYT 43 45.4 90408504 355.60 90410414 443.90300 125 TYT/TYT 56.0 90408507 551.70 90410415 689.70


All prices include TYTON sealing rings and, if required, a set of screws and a seal.



FITTINGS

VONROLL/DUKTUS MMK fittingDouble socket elbow

Version: TYTON socket joint | 11¼° or 22½° elbowStandards: EN 545 | Company standard | EN 14 901Material: Ductile cast iron | Epoxy resin coating or external bitumen and internal enamel

DN Deflection[°]

PFAbar

Weight/unitkg



80 11 100 8.3 90401001 68.70 90401002 76.30100 11 100 9.8 90400820 71.20 90400814 85.10125 11 64 12.0 90406599 85.10 90406600 107.80150 11 64 15.0 90400871 102.10 90400886 128.00200 11 64 21.5 90400875 141.20 90400890 184.70250 11 50 31.0 90400883 203.00 90400898 276.80300 11 50 40.5 90400902 274.90 90400909 360.00400 11 40 58.0 90400906 501.20 90400938 624.80500 11 40 90.0 90400956 1,194.80 90400957 1,439.40600 11 40 124.0 90400977 1,776.10 90407152 2,219.90700 11 30 260.0 90407866 2,766.60 90410429 3,174.50800 11 30 285.0 90407156 3,679.50 90407157 4,400.10

1000 11 30 499.0 90407200 5,735.50 90407164 7,488.20


DN Deflection[°]

PFAbar

Weight/unitkg



80 22 100 8.5 90401004 70.60 90401007 77.50100 22 100 10.0 90400821 74.40 90400815 89.50125 22 64 13.0 90406603 86.40 90406604 108.40150 22 64 16.0 90400872 103.40 90400887 134.90200 22 64 23.5 90400877 144.40 90400892 189.80250 22 50 33.0 90400884 210.00 90400899 286.20300 22 50 44.4 90400903 303.90 90400910 377.70400 22 40 66.5 90400939 532.80 90400940 694.80500 22 40 105.0 90400961 1,330.90 90400962 1,527.00600 22 40 147.0 90400981 1,928.60 90407153 2,380.10700 22 30 280.0 90407867 3,023.20 90410430 3,572.30800 22 30 308.0 90407159 4,118.30 90407160 4,924.70

1000 22 30 579.0 90407184 6,341.40 90407185 8,164.70





FITTINGS

VONROLL/DUKTUS MMK fittingDouble socket elbow

Version: TYTON socket joint | 30° or 45° elbowStandards: EN 545 | Company standard | EN 14 901Material: Ductile cast iron | Epoxy resin coating or external bitumen and internal enamel

DN Deflection[°]

PFAbar

Weight/unitkg



80 30 100 8.6 90401011 72.50 90401012 80.70100 30 100 10.5 90400822 75.00 90400816 90.80125 30 64 13.0 90406607 99.00 90406608 121.70150 30 64 16.5 90400873 104.70 90400888 104.70200 30 64 24.5 90402496 149.40 90400894 195.40250 30 50 34.0 90400900 216.90 90400907 295.10300 30 50 46.5 90400904 312.70 90400911 394.70400 30 40 69.2 90400946 592.00 90400947 754.70500 30 40 109.0 90400967 1,419.80 90400968 1,653.10600 30 40 155.0 90400982 1,960.20 90407154 2,450.10700 30 30 305.0 90407868 3,340.90 90410431 3,858.60800 30 30 360.0 90406914 4,245.70 90407161 5,138.40

1000 30 30 657.0 90407186 6,661.00 90407187 8,543.00



DN Deflection[°]

PFAbar

Weight/unitkg



80 45 100 8.8 90401013 75.00 90401017 82.60100 45 100 11.0 90400870 76.90 90400885 91.40125 45 64 14.0 90406611 100.20 90406612 124.80150 45 64 17.0 90400874 114.10 90400889 148.20200 45 64 27.0 90400881 166.40 90400896 218.10250 45 50 37.5 90400901 239.60 90400908 326.00300 45 50 52.5 90400905 343.00 90400912 455.80400 45 40 82.2 90400952 778.60 90400950 924.90500 45 40 135.0 90400973 1,503.70 90400969 1,825.90600 45 40 195.0 90400985 2,136.10 90407155 2,610.20700 45 30 340.0 90407869 3,691.50 90410432 4,422.80800 45 30 426.0 90400996 4,855.30 90407162 5,992.70

1000 45 30 740.0 90407188 7,362.10 90407189 9,832.40




DN PFAbar

Weight/unitkg



80 100 9.8 90400531 95.20 90400555 109.70100 100 12.0 90400516 99.60 90400538 119.20125 64 16.1 90406615 142.50 90406616 170.20150 64 21.0 90400519 161.40 90400542 192.30200 64 32.0 90400522 240.20 90400544 299.50250 50 46.0 90400626 689.70 90405376 864.40300 50 67.0 90400524 776.80 90407190 957.10400 40 127.0 90411397 1,633.60 90411612 2,123.50500 40 237.0 90400527 2,716.10 90407191 3,376.20600 40 368.0 90400529 3,320.10 90407192 3,972.00


VONROLL/DUKTUS MMQ fittingDouble socket elbow 90°

Version: TYTON socket joint | 90° elbowStandards: EN 545 | Company standard | EN 14 901Material: Ductile cast iron | Epoxy resin coating or external bitumen and internal enamel


FITTINGS



FITTINGS

VONROLL/DUKTUS MMR fittingDouble socket reduction piece

Version: TYTON socket jointStandards: EN 545 | Company standard | EN 14 901Material: Ductile cast iron | Epoxy resin coating or external bitumen and internal enamel

DN1 DN2 PFAbar

Weight/unitkg



125 80 64 9.1 90400649 114.10 90404402 148.20125 100 64 9.8 90400534 116.60 90400557 151.90200 100 64 18.6 90400651 179.70 90400692 233.90200 125 64 18.0 90404132 184.10 90400700 239.60200 150 64 18.5 90400653 186.60 90400695 242.70





FITTINGS

VONROLL MMA fittingDouble socket piece with a flanged branch

Version: Screw-gland socket joint | Branch flange jointStandards: EN 545 | EN 1092-2 | Company standard | EN 14 901Material: Ductile cast iron | Epoxy resin coating or external bitumen and internal enamel

DN1 DN2 PNbar

Weight/unitkg



125 40 10/16 18.3 90412590 367.60 90412591 426.20125 80 10/16 19.2 90400292 382.70 90400290 445.20125 100 10/16 19.6 90407086 382.70 90400272 445.20125 125 10/16 22.5 90407087 416.80 90407088 475.50150 40 10/16 20.2 90400318 432.50 90407089 496.80150 50 10/16 23.2 90407090 432.50 90400324 496.80150 80 10/16 23.8 90400333 432.50 90400331 496.80150 100 10/16 23.4 90400303 436.90 90400304 502.50150 150 10/16 27.4 90407091 474.10 90400312 549.10200 40 10/16 25.5 90407094 475.30 90407095 566.60200 50 10/16 25.6 90407097 475.30 90407098 566.60200 80 10/16 30.5 90400583 483.50 90403722 576.70200 100 10/16 31.5 90400341 483.50 90400339 576.70200 150 10/16 36.1 90407099 494.20 90400351 591.20200 200 10 44.0 90400365 521.30 90400366 626.50200 200 16 44.0 90413859 562.90 90410047 680.80


All prices include a set of screws and a seal and exclude flange joint parts.



FITTINGS

VONROLL U fittingPush-on sockets | PFA 16 bar

Version: Bolted-gland socket jointStandards: EN 545 | Company standard | EN 14 901Material: Ductile cast iron | Epoxy resin coating or external bitumen and internal enamel

DN Weight/unitkg



500 117.0 90404251 2,559.90 90403039 2,493.00600 142.0 90405377 2,978.80 90407067 3,075.10


All prices include a set of gland nuts and a seal.



FITTINGS


Version: Bolted-gland socket joint | Flange jointStandards: EN 545 | EN 1092-2 | Company standard | EN 14 901Material: Ductile cast iron | Epoxy resin coating or external bitumen and internal enamel

DN PNbar

Weight/unitkg



500 10 79.0 90406279 2,493.10 90407046 2,300.70500 16 79.0 90406927 2,674.00 90405508 2,581.20600 10 108.0 90406277 2,855.20 90406836 2,967.30600 16 108.0 90407435 3,084.10 90411474 3,261.10


All prices include a set of gland nuts and a seal and exclude flange joint parts.



VONROLL/DUKTUS MMK fittingDouble socket elbow | PFA 16 bar

Version: Bolted-gland socket joint | Elbow 11¼° or 22½° or 30° or 45°Standards: EN 545 | Company standardMaterial: Ductile cast iron | Epoxy resin coating in accordance with EN 14 901 and GSK RAL-GZ 662 or external bitu-

men and internal enamel

DN Deflection[°]

Weight/unitkg



500 11 154.0 90410417 3,851.60 90410416 4,141.70500 22 160.0 90410419 4,016.80 90410418 4,341.00600 11 174.0 90410421 4,410.60 90410420 4,749.70600 22 199.0 90410423 5,061.30 90410422 5,656.40600 30 199.0 90410425 5,135.10 90410424 5,745.30600 45 230.0 90407873 5,320.40 90410427 5,969.70


All prices include TYTON sealing rings, a set of gland nuts and a seal.

FITTINGS

VONROLL/DUKTUS hammer head boltsincluding nuts

Version: Gland nut socketStandards: DIN 28 602Material: Galvanised steel

DN Dimensions Quantity Part no. Price/unitSet €

500 M 20 x 100 16 700900976 82.30600 M 20 x 100 16 700900976 82.30



FITTINGS

VONROLL/DUKTUS N fitting90° double flange duckfoot bend

Version: Flange jointStandards: EN 545 | EN 1092-2 | Company standard | EN 14 901Material: Ductile cast iron | Epoxy resin coating or external bitumen and internal enamel

DN PNbar

Weight/unitkg



50 10/16 10.5 90411940 85.70 90411941 110.3080 10/16 14.0 90401954 81.30 90401955 108.40

100 10/16 21.0 90401956 98.40 90400706 136.80125 10/16 24.0 90411254 175.30 90411778 227.00150 10/16 32.5 90400737 176.90 90400745 239.00200 10 46.0 90400738 317.80 90400746 428.70200 16 46.0 90400739 389.60 90400747 505.60250 10 75.5 90404079 628.00 90403933 775.50250 16 75.5 90403785 726.30 90402280 979.80300 10 107.0 90400740 752.80 90400748 979.10300 16 107.0 90400741 889.60 90415835 1,112.20400 10 196.0 90400742 2,494.20 90405327 3,242.60400 16 196.0 90400743 2,962.60 90415836 3,679.50500 10 311.0 90400744 4,192.70 90407068 4,863.50500 16 311.0 90408124 4,414.60 90415837 5,518.60600 10 486.0 90406724 5,668.00 90407069 6,302.30600 16 486.0 90413795 5,789.70 90415838 7,237.30





FITTINGS

VONROLL/DUKTUS FF fittingFlanged pipes


DN PNbar


Weight/unitkg



50 10/16 100 5.5 90411897 69.40 90411898 90.8050 10/16 200 6.2 90411900 68.10 90411901 90.8050 10/16 300 7.1 90411903 68.10 90411904 90.8050 10/16 400 8.8 90411906 84.50 90411907 112.9050 10/16 500 9.9 90411909 84.50 90411910 112.9080 10/16 100 7.5 90402424 55.50 90401515 73.8080 10/16 150 8.4 90401158 57.10 90401196 73.8080 10/16 200 8.9 90402553 58.00 90401518 73.8080 10/16 250 10.0 90401160 71.90 90401891 87.6080 10/16 300 11.0 90403094 70.60 90401521 88.9080 10/16 400 12.5 90401526 81.00 90401527 109.1080 10/16 500 13.5 90401530 81.00 90401531 109.1080 10/16 600 16.0 90401533 148.80 90401534 198.0080 10/16 700 17.8 90402721 148.80 90405239 198.0080 10/16 800 18.5 90401809 160.80 90402882 209.3080 10/16 1000 22.0 90401813 169.00 90402144 225.70





FITTINGS



DN PNbar


Weight/unitkg



100 10/16 100 8.8 90401816 64.30 90402883 86.40100 10/16 150 9.9 90402433 64.30 90402788 86.40100 10/16 200 11.0 90401820 64.30 90401821 86.40100 10/16 250 11.5 90401390 76.90 90403047 100.90100 10/16 300 13.5 90402725 76.90 90401823 100.90100 10/16 400 15.0 90401827 97.40 90401828 131.10100 10/16 500 17.0 90401831 97.70 90401832 131.10100 10/16 600 19.5 90402425 167.70 90401834 218.80100 10/16 700 21.5 90402727 169.00 90402884 221.30100 10/16 800 24.0 90402459 170.20 90402887 230.10100 10/16 1000 27.5 90402731 179.70 90401844 241.50125 10/16 100 10.6 90402426 105.30 90401380 105.30125 10/16 150 10.0 90402451 108.40 90405392 140.60125 10/16 200 13.5 90402011 108.40 90404362 140.60125 10/16 250 14.6 90402244 111.00 90406854 149.40125 10/16 300 15.2 90402732 111.00 90402733 149.40125 10/16 400 17.6 90402427 151.90 90405623 196.70125 10/16 500 21.6 90402734 151.90 90404396 196.70125 10/16 600 23.3 90402428 242.70 90404345 316.50125 10/16 700 24.0 90401855 280.60 90406857 371.40125 10/16 800 29.0 90401164 280.60 90406862 371.40125 10/16 1000 32.0 90402429 261.70 90404245 336.70





FITTINGS



DN PNbar


Weight/unitkg



150 10/16 100 13.6 90402738 99.60 90401862 133.70150 10/16 150 15.0 90401209 99.60 90402789 133.70150 10/16 200 16.0 90401865 99.60 90401866 133.70150 10/16 250 18.2 90401914 119.80 90401902 160.80150 10/16 300 18.5 90401869 119.80 90401870 157.60150 10/16 400 21.5 90401873 139.00 90401874 194.80150 10/16 500 24.5 90402744 148.20 90401877 207.40150 10/16 600 29.6 90402431 220.00 90402961 283.70150 10/16 700 32.5 90401881 247.10 90402962 321.50150 10/16 800 36.0 90402188 247.10 90401883 321.50150 10/16 1000 42.5 90401190 274.30 90401886 368.80150 10/16 1100 45.7 90406873 1,005.60150 10/16 1200 48.7 90405963 1,047.20150 10/16 1300 51.9 90406872 1,108.40150 10/16 1400 61.6 90406871 1,148.10150 10/16 1500 61.6 90403757 1,182.80150 10/16 1600 64.6 90402547 1,224.40





FITTINGS



DN PNbar


Weight/unitkg



200 10 100 18.7 90402748 131.80 90414610 181.60200 10 150 21.5 90402227 131.80 90404398 166.40200 10 200 30.0 90402751 131.80 90402752 177.80200 10 250 26.5 90402229 164.60 90405897 221.90200 10 300 30.0 90402753 155.10 90403899 206.80200 10 400 34.0 90402755 190.40 90401382 257.90200 10 500 38.5 90401905 199.20 90401906 280.60200 10 600 41.5 90402756 297.00 90402757 385.90200 10 700 46.0 90402758 334.20 90406878 435.00200 10 800 50.5 90402759 344.90 90402969 448.90200 10 1000 60.5 90402762 355.00 90402997 471.00200 10 1100 64.3 90406953 1,266.00200 10 1200 68.0 90403859 1,293.80200 10 1300 73.5 90403755 1,317.10200 10 1400 83.2 90406885 1,363.70200 10 1500 83.2 90404815 1,441.30200 10 1600 93.0 90406884 1,465.20200 16 100 18.7 90406338 153.20 90404397 193.60200 16 150 21.5 90407812 146.30 90408509 188.50200 16 200 30.0 90405715 146.30 90415733 199.20200 16 250 26.5 90408346 182.20 90415734 247.10200 16 300 30.0 90402754 171.80 90414514 232.00200 16 400 34.0 90406378 211.80 90414531 288.10200 16 500 38.5 90405737 221.30 90403865 308.90200 16 600 41.5 90404814 341.10 90415735 426.80200 16 700 46.0 90406377 384.00 90415736 480.40200 16 800 50.5 90403946 397.80 90413826 517.00200 16 1000 60.5 90405447 399.10 90402262 518.90200 16 1100 64.3 90409641 1,394.00200 16 1200 68.0 90412744 1,422.40200 16 1300 73.5 90415722 1,448.20200 16 1400 83.2 90415723 1,499.90200 16 1500 83.2 90409489 1,585.70200 16 1600 93.0 90411326 1,613.40





FITTINGS



DN PNbar


Weight/unitkg



250 10 100 24,6 90411912 234,50 90411913 304,50250 10 200 33,0 90415152 225,10 90415154 293,80250 10 300 42,0 90411623 234,50 90411625 316,50250 10 400 43,0 90415156 324,70 90415158 422,40250 10 500 51,0 90411627 343,00 90411629 446,40250 10 800 62,5 90404333 580,70 90403991 725,70250 10 1000 71,0 90403671 515,10 90403948 670,20250 10 1200 98,8 90406956 1.524,50250 16 100 24,6 90413711 269,80 90413785 351,20250 16 200 33,0 90415153 259,10 90415155 337,30250 16 300 42,0 90412540 260,40 90412542 364,40250 16 400 43,0 90415157 373,20 90415159 484,80250 16 500 51,0 90412299 394,10 90413352 513,80250 16 800 62,5 90408046 667,10 90415737 834,80250 16 1000 71,0 90406668 592,70 90415738 742,70250 16 1200 98,8 90415724 1.708,00300 10 100 32,7 90411916 257,20 90411917 334,80300 10 200 39,4 90411920 247,80 90411921 333,50300 10 300 46,1 90411924 291,30 90411925 350,50300 10 400 52,8 90411928 394,10 90411929 510,70300 10 500 59,5 90401930 381,40 90403682 494,90300 10 1000 90,5 90402764 556,70 90404783 781,20300 16 100 32,7 90413790 296,30 90413786 385,20300 16 200 39,4 90413747 274,90 90413787 368,20300 16 300 46,1 90413625 324,10 90413788 401,00300 16 400 52,8 90413651 437,60 90413789 588,20300 16 500 59,5 90406180 423,70 90415739 568,70300 16 1000 90,5 90405969 747,10 90415740 935,00400 10 500 90,7 90401938 810,20 90406957 1.011,90400 10 1000 148,5 90402765 2.011,90 90406958 2.446,90400 10 2000 293,0 90407575 3.515,60400 16 500 90,7 90409219 931,20 90415741 1.163,90400 16 1000 148,5 90406243 2.313,90 90415742 2.815,10400 16 2000 293,0 90407576 4.148,60500 10 1000 258,0 90405192 2.576,20 90408730 3.293,00500 10 2000 524,0 90406960 4.618,30500 16 1000 258,0 90408042 2.962,60 90415743 3.787,30500 16 2000 524,0 90411390 5.314,30





FITTINGS



DN PNbar


Weight/unitkg



600 10 500 233.0 90406987 2,073.70 90406963 3,216.70600 10 600 309.0 90406989 2,666.90 90406964 3,653.60600 10 700 263.0 90406988 2,803.10 90406965 4,053.40600 10 800 261.0 90406984 2,988.50 90406966 4,182.00600 10 1000 291.0 90406302 2,743.20 90406967 4,275.30600 10 1100 310.0 90406977 3,468.96600 10 1200 330.0 90406990 4,043.65600 10 1300 350.0 90406983 4,173.91600 10 1400 370.0 90406982 4,304.16600 10 1500 397.0 90406981 4,448.63600 10 1600 422.0 90406980 4,828.44600 10 1700 448.0 90406978 4,933.03600 10 1800 465.0 90406979 6,485.86600 10 1900 475.0 90406991 6,613.63600 10 2000 500.0 90406637 5,390.60600 16 500 233.0 90410155 2,384.50 90415744 3,699.70600 16 600 309.0 90415141 3,067.30 90415745 4,202.20600 16 700 263.0 90415160 3,382.50 90415746 4,662.40600 16 800 261.0 90415166 3,437.40 90415747 4,808.70600 16 1000 291.0 90410154 3,212.90 90415748 4,916.50600 16 1100 310.0 90415725 5,347.45600 16 1200 330.0 90415726 6,030.99600 16 1300 350.0 90415727 6,242.79600 16 1400 370.0 90411559 4,924.93600 16 1500 397.0 90415728 6,685.15600 16 1600 422.0 90415729 7,186.94600 16 1700 448.0 90415730 9,028.29600 16 1800 465.0 90415731 9,262.70600 16 1900 475.0 90415732 9,450.96600 16 2000 500.0 90411325 6,200.80800 10 500 280.0 90411616 3,803.10 90411618 5,023.10800 10 1000 513.0 90404895 4,521.80 90406998 7,524.80800 10 2000 782.0 90407001 7,475.60800 16 500 280.0 90411562 4,362.90 90415749 5,326.10800 16 1000 513.0 90409834 5,489.00 90415750 7,964.50800 16 2000 782.0 90414650 8,595.40

1000 10 500 440.0 90407015 6,669.90 90407011 8,384.801000 10 600 540.0 90407012 7,746.10 90407010 9,880.901000 10 800 750.0 90407013 8,910.60 90407004 11,836.001000 10 1000 923.0 90407014 9,990.00 90407003 12,858.701000 10 2000 1,450.0 90411253 16,931.601000 16 500 440.0 90415167 7,671.10 90415751 9,083.451000 16 600 540.0 90415168 8,908.10 90415752 10,374.101000 16 800 750.0 90415169 10,248.50 90415753 12,189.201000 16 1000 923.0 90409806 11,488.70 90415754 13,892.30





FITTINGS

VONROLL/DUKTUS FFK fittingDouble flange elbow

Version: Flange joint | Elbow 11¼° or 22½° or 30° or 45°Standards: EN 545 | EN 1092-2 | Company standard | EN 14 901Material: Ductile cast iron | Epoxy resin coating or external bitumen and internal enamel

DN PNbar

Deflection[°]

Weight/unitkg



80 10/16 11 9.7 90402444 104.70 90402810 139.3080 10/16 22 10.7 90403853 104.70 90402806 139.3080 10/16 30 9.6 90402449 104.70 90402820 139.3080 10/16 45 9.8 90402410 78.20 90401355 100.20

100 10/16 11 12.0 90402397 117.60 90401300 154.50100 10/16 22 12.0 90402401 117.60 90401317 154.50100 10/16 30 12.0 90402406 117.90 90401342 154.50100 10/16 45 12.0 90401358 90.80 90401359 119.20125 10/16 11 16.0 90411256 186.00 90411602 232.60125 10/16 22 16.0 90411258 186.00 90411604 232.60125 10/16 30 15.0 90408223 186.00 90408228 232.60125 10/16 45 15.0 90408224 138.70 90408229 173.40150 10/16 11 19.5 90402446 194.80 90402811 252.20150 10/16 22 19.5 90402448 194.80 90401321 252.20150 10/16 30 20.0 90402407 194.80 90402821 252.20150 10/16 45 19.5 90402413 141.90 90401362 188.50200 10 11 26.0 90402442 321.50 90405163 417.40200 10 22 29.0 90402445 321.50 90405164 417.40200 10 30 28.5 90402408 321.50 90405165 417.40200 10 45 29.0 90401365 241.50 90401366 313.30200 16 11 26.0 90406028 366.90 90415755 458.40200 16 22 29.0 90407569 366.90 90415756 458.40200 16 30 28.5 90405894 366.90 90415757 458.40200 16 45 29.0 90405576 275.50 90406904 344.90





FITTINGS

VONROLL/DUKTUS FFK fittingDouble flange elbow

Version: Flange joint | Elbow 11¼° or 22½° or 30° or 45°Standards: EN 545 | EN 1092-2 | Company standard | EN 14 901Material: Ductile cast iron | Epoxy resin coating or external bitumen and internal enamel

DN PNbar

Deflection[°]

Weight/unitkg



250 10 11 44.3 90405582 466.60 90404452 629.20250 10 22 44.5 90403902 466.60 90404453 628.60250 10 30 42.5 90402772 466.60 90406313 628.60250 10 45 52.5 90402416 406.00 90404795 545.40250 16 11 44.3 90407570 542.20 90415758 678.40250 16 22 44.5 90406352 542.20 90415759 678.40250 16 30 44.6 90403013 542.20 90415760 678.40250 16 45 54.0 90407571 465.90 90415761 581.90300 10 11 60.0 90402443 665.20 90405657 861.90300 10 22 65.0 90402447 665.20 90405658 861.90300 10 30 68.0 90404464 665.20 90405661 861.90300 10 45 75.0 90402277 545.40 90401378 752.80300 16 11 63.5 90404866 793.80 90415762 993.00300 16 22 67.0 90404865 793.80 90415763 993.00300 16 30 69.0 90404864 793.80 90415764 993.00300 16 45 79.0 90407302 608.40 90415765 787.50400 10 11 58.0 90406013 851.20 90407005 1,064.30400 10 22 65.0 90402405 911.70 90406249 1,139.90400 10 30 72.0 90404981 974.10 90407006 1,217.50400 10 45 94.0 90404980 1,005.60 90407007 1,258.40400 16 11 67.0 90407574 979.80 90415766 1,224.40400 16 22 72.0 90407573 1,048.50 90415767 1,310.80400 16 30 81.0 90407572 1,121.60 90415768 1,402.80400 16 45 118.0 90407437 1,156.30 90415769 1,445.70500 10 11 103.0 90405884 1,352.40 90405449 1,757.80500 10 22 118.0 90407064 1,489.20 90405450 1,938.10500 10 30 128.0 90405882 1,701.00 90407008 2,211.10500 10 45 169.0 90403813 1,857.40 90407009 2,415.40500 16 11 112.0 90407438 1,622.90 90415770 2,028.30500 16 22 125.0 90407439 1,786.80 90415771 2,234.40500 16 30 138.0 90412086 2,041.50 90415772 2,552.20500 16 45 186.0 90406730 2,233.20 90415773 2,791.10600 10 11 160.0 90405426 3,155.60 90407024 4,101.90600 10 22 174.0 90407025 3,155.60 90407028 4,101.90600 10 30 213.0 90407029 3,155.60 90407030 4,101.90600 10 45 251.0 90406233 3,086.20 90407031 4,011.80600 16 11 170.0 90408497 3,787.30 90415804 4,734.30600 16 22 225.0 90410279 3,787.30 90415805 4,734.30600 16 30 225.0 90411324 3,787.30 90415806 4,734.30600 16 45 301.0 90409119 3,703.50 90415807 4,629.00800 10 11 366.0 90407033 4,022.50 90407040 5,740.50800 10 30 428.0 90405770 4,993.40 90407042 7,121.90800 10 45 428.0 90405832 5,236.20 90407043 7,437.20800 16 11 428.0 90415171 4,827.00 90415808 6,601.80800 16 30 430.0 90411504 5,992.10 90415809 8,190.60800 16 45 430.0 90411505 6,283.40 90415810 8,552.50





FITTINGS

VONROLL/DUKTUS Q fitting90° double flange elbow

Version: Flange jointStandards: EN 545 | EN 1092-2 | Company standardMaterial: Ductile cast iron | Epoxy resin coating in accordance with EN 14 901 and GSK RAL-GZ 662 or external bitu-


DN PNbar

Weight/unitkg



50 10/16 6.7 90411943 71.90 90411944 82.6080 10/16 9.9 90401396 81.30 90401397 97.70

100 10/16 12.5 90401070 90.20 90401078 111.00125 10/16 16.0 90408227 124.80 90408230 153.80150 10/16 21.0 90401071 146.30 90401079 174.60200 10 31.5 90401072 233.30 90401080 315.90200 16 32.0 90401073 279.90 90401081 356.90250 10 49.0 90401075 380.80 90401030 513.20250 16 52.0 90401074 425.30 90402465 531.50300 10 69.0 90401038 459.00 90401033 617.20300 16 72.0 90401040 529.60 90401035 706.80400 10 126.0 90401046 1,598.30 90401043 1,980.30400 16 137.0 90401048 1,974.00 90415840 2,467.70500 10 180.0 90401054 2,687.10 90401051 2,673.90500 16 204.0 90401056 3,085.00 90415841 3,085.00600 10 269.0 90402835 3,644.80 90407071 4,555.90600 16 322.0 90410316 4,373.70 90415842 5,467.50800 10 527.0 90405960 5,614.40 90407072 7,259.20800 16 547.0 90414585 6,455.50 90415843 8,393.60


Note that all prices exclude flange joint parts.



FITTINGS

VONROLL/DUKTUS FFR fittingDouble flange reduction piece


DN1 DN2 PNbar


Weight/unitkg



80 50 10/16 200 7.5 90400075 59.30 90400076 78.8080 65 10/16 200 8.8 90408233 81.30 90408234 91.40

100 50 10/16 200 8.5 90401403 59.30 90401404 78.20100 65 10/16 200 9.5 90411277 82.60 90411280 98.40100 80 10/16 200 9.6 90401407 70.60 90401408 88.30125 80 10/16 200 11.5 90408186 77.50 90408187 102.10125 100 10/16 200 12.5 90408190 79.40 90409191 103.40150 80 10/16 200 12.5 90401413 87.60 90401414 115.40150 100 10/16 200 14.0 90402483 88.90 90401417 122.90150 125 10/16 200 13.5 90402487 95.80 90401420 124.80200 80 10 300 17.5 90402440 129.90 90402837 174.60200 100 10 300 20.0 90402265 129.90 90401423 174.60200 125 10 300 21.0 90402441 162.00 90401170 203.60200 150 10 300 23.0 90402489 133.00 90401427 179.70200 80 16 300 17.5 90405717 150.10 90406331 194.20200 100 16 300 20.0 90405509 145.60 90406702 203.00200 125 16 300 21.0 90404557 185.40 90413983 240.80200 150 16 300 23.0 90405448 163.30 90404982 220.00250 80 10 300 27.0 90411430 218.10 90411606 274.90250 100 10 300 28.0 90411434 210.60 90411607 275.50250 150 10 300 28.0 90402839 210.60 90402494 275.50250 200 10 300 28.5 90401163 210.60 90402469 275.50250 80 16 300 27.0 90411431 263.50 90415811 331.00250 100 16 300 28.0 90411435 254.70 90413911 319.00250 150 16 300 28.0 90406662 254.70 90414436 319.00250 200 16 300 28.5 90405974 254.70 90410872 319.00300 100 10 300 36.0 90411631 251.60 90411633 338.60300 150 10 300 39.0 90410143 251.60 90410144 338.60300 200 10 300 39.0 90400045 251.60 90400046 338.60300 250 10 300 43.5 90400050 258.50 90400054 355.60300 100 16 300 36.0 90412311 308.60 90415813 401.00300 150 16 300 41.5 90410345 308.30 90410346 401.00300 200 16 300 44.0 90400047 302.60 90409129 401.00300 250 16 300 45.5 90404912 315.90 90406353 411.10





FITTINGS

VONROLL/DUKTUS FFR fittingDouble flange reduction piece


DN1 DN2 PNbar


Weight/unitkg



400 200 10 300 57.0 90413727 619.10 90413728 728.20400 250 10 300 52.0 90406012 619.10 90407044 728.20400 300 10 300 56.0 90400058 569.30 90400059 654.40400 200 16 300 60.0 90414355 660.70 90414354 858.70400 250 16 300 57.0 90405872 660.70 90415814 858.70400 300 16 300 67.0 90407359 717.50 90415815 849.30500 300 10 600 110.0 90411932 1,354.30 90411933 1,703.60500 400 10 600 128.5 90411936 1,434.30 90411937 2,468.30500 300 16 600 126.5 90413731 1,547.20 90413732 2,734.40500 400 16 600 145.0 90413723 1,650.00 90413724 2,838.40600 400 10 600 156.0 90400068 1,863.10 90400069 2,788.00600 400 16 600 170.0 90411323 2,142.40 90415816 3,206.00





FITTINGS

VONROLL/DUKTUS N fitting90° double flange duckfoot bend

Version: Flange jointStandards: EN 545 | EN 1092-2 | Company standardMaterial: Ductile cast iron | Epoxy resin coating in accordance with EN 14 901 and GSK RAL-GZ 662 or external bitumen and internal enamel

DN PNbar

Weight/unitkg



50 10/16 10.5 90411940 85.70 90411941 110.3080 10/16 14.0 90401954 81.30 90401955 108.40

100 10/16 21.0 90401956 98.40 90400706 136.80125 10/16 25.0 90411254 175.30 90411778 227.00150 10/16 32.5 90400737 176.90 90400745 239.00200 10 46.0 90400738 317.80 90400746 428.70200 16 46.0 90400739 389.60 90400747 505.60250 10 75.5 90404079 628.00 90403933 775.50250 16 75.5 90403785 726.30 90402280 979.80300 10 104.0 90400740 752.80 90400748 979.10300 16 107.0 90400741 889.60 90415835 1,112.20400 10 196.0 90400742 2,494.20 90405327 3,242.60400 16 198.0 90400743 2,943.70 90415836 3,679.50500 10 281.0 90400744 4,192.70 90407068 4,863.50500 16 311.0 90408124 4,414.60 90415837 5,518.60600 10 486.0 90406724 5,668.00 90407069 6,302.30600 16 502.0 90413795 5,789.70 90415838 7,237.30





FITTINGS

VONROLL/DUKTUS T fittingDouble flange piece with a flanged branch



DN1 DN2 PNbar

Weight/unitkg



50 50 10/16 10.5 90402423 85.10 90403015 110.3080 50 10/16 14.5 90401443 93.30 90401444 123.6080 65 10/16 16.0 90411696 117.30 90411698 159.5080 80 10/16 17.0 90401447 98.40 90401448 138.10

100 50 10/16 17.0 90404373 107.80 90404456 148.20100 65 10/16 19.0 90411700 121.70 90411702 158.30100 80 10/16 19.0 90401120 103.40 90401112 140.60100 100 10/16 20.0 90401119 105.30 90401111 143.80125 80 10/16 22.0 90401123 130.50 90401115 179.70125 100 10/16 23.5 90401121 140.00 90401113 186.00125 125 10/16 25.0 90401122 146.90 90401114 192.30150 50 10/16 30.0 90411687 177.20 90411689 230.80150 80 10/16 29.5 90401450 160.80 90401127 220.00150 100 10/16 30.0 90401124 163.30 90401116 225.70150 125 10/16 32.5 90402436 183.50 90401117 239.00150 150 10/16 34.0 90401125 168.30 90401126 245.30200 80 10 42.0 90401454 243.40 90401455 331.00200 100 10 42.5 90401459 245.90 90401128 320.90200 125 10 51.0 90411692 286.20 90411694 372.00200 150 10 46.5 90401462 250.30 90401131 339.80200 200 10 49.5 90401466 257.20 90401133 350.50200 80 16 42.5 90402507 268.00 90406332 348.70200 100 16 45.0 90404914 276.20 90401129 353.10200 125 16 51.0 90412977 317.80 90415845 412.30200 150 16 48.0 90404886 280.60 90401132 365.70200 200 16 51.0 90404199 288.80 90406328 375.80




FITTINGS



DN1 DN2 PNbar

Weight/unitkg



250 80 10 68.0 90401471 423.10 90403670 570.60250 100 10 67.0 90402437 423.10 90403816 570.60250 150 10 81.0 90401477 452.70 90402513 609.70250 200 10 76.5 90402221 481.10 90403703 625.40250 250 10 82.5 90401482 488.60 90403077 663.30250 80 16 72.0 90404910 491.10 90411230 638.70250 100 16 71.0 90404686 491.10 90411231 638.70250 150 16 82.0 90406181 477.90 90410128 621.70250 200 16 78.5 90406182 539.10 90415846 701.10250 250 16 84.5 90403786 546.00 90406333 709.90300 80 10 96.5 90401485 504.40 90402850 716.90300 100 10 94.4 90402294 513.80 90401488 727.60300 150 10 103.0 90402095 554.80 90402096 776.10300 200 10 107.0 90401491 554.80 90402852 776.10300 250 10 112.0 90404147 628.00 90404409 816.50300 300 10 117.0 90401493 597.10 90402856 879.50300 80 16 98.0 90405483 595.80 90403080 773.60300 100 16 98.0 90406183 599.60 90408938 771.70300 150 16 104.0 90405739 640.60 90402228 789.40300 200 16 107.0 90405446 640.60 90415848 789.40300 250 16 114.0 90406172 740.80 90405167 963.40300 300 16 119.0 90402857 725.10 90414632 942.60400 80 10 141.0 90402381 1,328.40 90406245 1,726.90400 100 10 143.5 90402526 1,328.40 90402859 1,726.90400 150 10 150.0 90401498 1,337.30 90406248 1,737.60400 200 10 155.0 90403916 1,337.30 90406247 1,737.60400 300 10 175.0 90403782 1,819.60 90403932 2,325.80400 400 10 180.0 90401503 1,925.50 90403937 2,617.80400 80 16 143.0 90406568 1,567.40 90406246 2,037.10400 100 16 146.0 90406752 1,567.40 90415849 2,037.10400 150 16 153.0 90406570 1,578.10 90408771 2,051.00400 200 16 160.0 90404546 1,578.10 90414819 2,051.00400 300 16 180.0 90406751 2,092.60 90415851 2,610.20400 400 16 195.0 90405910 2,214.90 90409069 3,012.40





FITTINGS




DN1 DN2 PNbar

Weight/unitkg



500 80 10 200.0 90406721 2,158.10 90407201 2,806.30500 100 10 210.0 90406622 2,173.90 90403614 2,773.50500 150 10 216.0 90402236 2,188.40 90406487 2,845.40500 200 10 224.0 90402528 2,188.40 90403882 2,845.40500 250 10 225.0 90407202 2,188.40 90407203 2,845.40500 300 10 231.0 90402531 2,367.50 90407204 3,076.80500 500 10 340.0 90402869 2,987.20 90402533 3,984.60500 80 16 203.0 90409000 2,590.00 90415852 3,237.50500 100 16 240.0 90406019 2,559.80 90414213 3,327.70500 150 16 245.0 90408043 2,626.00 90415847 3,282.90500 200 16 235.0 90406020 2,626.00 90415850 3,282.90500 250 16 240.0 90408698 2,626.00 90415853 3,282.90500 300 16 245.0 90408125 2,841.00 90415854 3,551.50500 500 16 350.0 90409769 3,429.80 90414214 4,520.60600 100 10 334.0 90405823 3,767.10 90407205 4,886.20600 150 10 320.0 90402456 3,603.20 90407206 4,886.20600 200 10 330.0 90404897 3,603.20 90407207 4,886.20600 250 10 335.0 90407208 3,789.20 90407209 4,927.20600 300 10 360.0 90402537 3,789.20 90407210 4,927.20600 400 10 370.0 90407211 3,789.20 90407212 4,927.20600 500 10 389.0 90402539 4,125.90 90407213 5,327.60600 600 10 439.0 90402540 4,438.60 90407214 5,729.80600 100 16 354.0 90406565 4,332.00 90415855 6,030.60600 150 16 356.0 90406566 4,323.80 90415856 6,030.60600 200 16 377.7 90407419 4,323.80 90415857 6,030.60600 250 16 402.0 90411352 4,546.40 90415858 6,159.20600 300 16 466.0 90410317 4,546.40 90415859 6,159.20600 400 16 407.0 90411812 4,546.40 90415860 6,159.20600 500 16 429.0 90412270 4,744.40 90415861 6,661.00600 600 16 530.0 90410126 5,103.80 90415862 7,162.30




FITTINGS



DN1 DN2 PNbar

Weight/unitkg



800 100 10 392.0 90406144 6,616.30 90407215 8,602.90800 150 10 389.0 90407216 6,616.30 90407217 8,602.90800 200 10 400.0 90405961 6,616.30 90407218 8,602.90800 250 10 410.0 90407244 6,898.10 90407246 8,967.40800 300 10 420.0 90407245 6,898.10 90407247 8,967.40800 400 10 461.0 90407219 6,898.10 90407223 8,967.40800 500 10 647.0 90407221 7,133.30 90407224 9,273.10800 600 10 730.0 90407222 7,133.30 90407225 9,273.10800 800 10 780.0 90404894 7,671.70 90407226 9,974.20800 100 16 420.0 90409955 7,939.00 90415863 7,321.90800 150 16 397.0 90411956 7,939.00 90415864 7,838.72800 200 16 400.0 90413172 7,939.00 90415865 7,556.55800 250 16 410.0 90415844 8,297.10 90415866 7,459.41800 300 16 420.0 90409956 8,297.10 90415867 6,943.13800 400 16 485.0 90415173 8,297.10 90415868 7,974.58800 500 16 699.0 90409835 8,559.40 90415869 10,886.86800 600 16 765.0 90407505 8,559.40 90415870 10,548.54800 800 16 800.0 90411955 9,207.60 90415871 12,811.75

1000 150 10 540.0 90413022 9,602.20 90415891 11,855.181000 200 10 545.0 90413028 9,791.40 90415893 11,709.431000 250 10 548.0 90413034 9,791.40 90415895 11,878.441000 300 10 556.0 90413040 10,724.50 90415897 12,510.481000 400 10 852.0 90407231 11,046.10 90407236 15,254.001000 500 10 930.0 90407232 11,225.70 90407237 15,451.611000 600 10 1100.0 90407233 11,224.50 90407238 15,132.411000 800 10 1147.0 90407234 11,433.80 90407239 14,043.721000 1000 10 1340.0 90407235 12,552.90 90407240 19,229.961000 150 16 615.0 90413023 11,523.30 90415892 10,424.481000 200 16 640.0 90413029 11,749.00 90415894 11,182.881000 250 16 635.0 90413035 11,749.00 90415896 10,810.521000 300 16 660.0 90413041 12,866.30 90415898 10,694.581000 400 16 852.0 90413046 12,871.30 90415872 12,472.501000 500 16 1395.0 90415174 13,476.60 90415873 16,124.791000 600 16 1175.0 90413048 13,475.30 90415874 17,675.531000 800 16 1147.0 90413049 13,856.70 90415875 15,558.851000 1000 16 1365.0 90413050 15,066.60 90415876 19,655.29





FITTINGS

VONROLL/DUKTUS TT fittingDouble flange piece with two flanged branches

Version: Flange jointStandards: Company standard | EN 1092-2 | Company standardMaterial: Ductile cast iron | Epoxy resin coating in accordance with EN 14 901 and GSK RAL-GZ 662 or external bitumen and internal enamel


DN1 DN2 PNbar

Weight/unitkg



80 80 10/16 20.5 90402439 211.80 90404222 263.50100 100 10/16 23.6 90404089 230.80 90402358 298.80125 125 10/16 35.0 90408235 368.80 90408237 461.50150 150 10/16 38.0 90402371 454.60 90402372 568.10200 200 10 58.0 90404908 621.00 90403992 807.00200 200 16 60.7 90405593 745.90 90415877 931.90300 300 10 167.0 90405705 1,935.60 90405968 2,421.10300 300 16 170.0 90408911 2,324.00 90415878 2,904.60400 400 10 239.0 90406665 2,504.30 90407066 3,256.40400 400 16 241.0 90406636 3,006.80 90415879 3,581.80




FITTINGS

VONROLL/DUKTUS X fittingBlanking flange


DN PNbar

Weight/unitkg



40 10/16 1.9 90402222 23.30 90410795 27.1050 10/16 2.5 90402747 26.50 90407662 30.3065 10/16 3.2 90402304 30.30 90407663 39.1080 10/16 4.0 90402258 26.50 90407791 34.00

100 10/16 4.4 90402255 29.60 90407665 39.10125 10/16 5.6 90403697 42.20 90410796 55.50150 10/16 7.3 90402308 58.60 90407666 74.40200 10 11.5 90402332 79.40 90407667 116.60200 16 12.0 90405494 85.10 90413810 119.20250 10 17.5 90402333 121.10 90408011 160.80250 16 17.5 90403787 139.30 90415616 181.60300 10 23.0 90402337 165.80 90407668 232.00300 16 23.0 90405740 198.00 90415617 257.20350 10 34.0 90414351 361.30 90414350 469.70350 16 34.0 90415120 415.50 90415161 539.70400 10 42.0 90402338 368.80 90407790 543.50400 16 42.0 90405851 433.80 90415618 625.40500 10 68.0 90405046 499.30 90408012 718.80500 16 68.0 90407829 599.60 90415619 826.60600 10 97.0 90405818 655.70 90408013 978.50600 16 97.0 90414553 787.50 90415620 1,293.10700 10 175.0 90406382 1,586.90 90410797 2,565.93800 10 227.0 90404896 2,008.70 90410798 3,267.18900 10 273.0 90406827 2,260.90 90410799 3,594.69

1000 10 453.0 90406824 3,125.30 90410800 5,374.62

EPOXY ENAMEL/ENAMEL

Note that all prices exclude flange joint parts. Surcharge for threaded holes



FITTINGS

VONROLL/DUKTUS XR fittingReducing flange

Version: Flange jointStandards: Company standard | EN 1092-2Material: Ductile cast iron | Epoxy resin coating in accordance with EN 14 901 and GSK RAL-GZ 662 | Galvanised or stainless steel bolts

GALVANISED BOLTS STAINLESS STEEL BOLTS

DN1 DN2 PNbar

Version Weight/unitkg



80 50 10/16 4/4 hole 6 .0 90407158 80 .70 90407248 91 .4080 50 10/16 8/4 hole 6 .8 90407166 90 .80 90407249 100 .9080 65 10/16 8/4 hole 6 .0 90407167 95 .20 90407250 108 .4080 80 10/16 4/8 hole 5 .8 90403904 95 .80 90407251 112 .90

100 50 10/16 8/4 hole 6 .5 90413791 100 .20 90413792 115 .40100 65 10/16 8/4 hole 7 .0 90407169 100 .20 90407253 115 .40100 80 10/16 4/8 hole 8 .0 90407170 100 .20 90407254 115 .40100 80 10/16 8/4 hole 8 .0 90407171 100 .20 90407255 115 .40100 80 10/16 8/8 hole 9 .8 90403844 124 .80 90407256 137 .40100 100 10/16 4/8 hole 8 .0 90407172 100 .20 90407257 115 .40125 100 10/16 8/4 hole 8 .0 90407174 119 .80 90407259 137 .40125 100 10/16 4/8 hole 8 .0 90407176 119 .80 90407261 137 .40125 100 10/16 8/8 hole 8 .0 90404798 133 .00 90407262 153 .20150 80 10/16 8/4 hole 11 .0 90407177 132 .40 90407263 154 .50150 80 10/16 8/8 hole 11 .0 90402544 152 .60 90407264 175 .90150 100 10/16 8/8 hole 13 .0 90403052 165 .80 90407265 191 .00150 125 10/16 8/8 hole 9 .6 90413793 237 .70 90413794 263 .50




FITTINGS

VONROLL/DUKTUS XR fittingReducing flange

Version: Flange jointStandards: Company standard | EN 1092-2Material: Ductile cast iron | Epoxy resin coating in accordance with EN 14 901 and GSK RAL-GZ 662 | Galvanised or stainless steel bolts

GALVANISED BOLTS STAINLESS STEEL BOLTS

DN1 DN2 PNbar




200 80 10 8/4 hole 17.0 90411969 170.20 90411970 196.10200 80 10 8/8 hole 17.0 90411945 258.50 90411946 224.50200 100 10 8/4 hole 15.0 90408292 225.10 90408293 259.10200 100 10 8/8 hole 15.0 90408094 195.40 90408294 224.50200 150 10 8/8 hole 18.0 90407324 235.80 90409362 254.70200 200 10 12/8 hole 11.2 90413798 90413796 388.40200 80 16 12/8 hole 17.0 90411971 224.50 90411972 258.50200 100 16 12/8 hole 15.0 90408095 224.50 90408295 258.50200 150 16 12/8 hole 18.0 90410441 251.60 90407325 295.10200 200 16 12/8 hole 11.2 90413798 90413796 388.40250 80 10 12/8 hole 20.0 90406818 368.80 90407266 424.90250 150 10 12/8 hole 20.5 90407182 420.50 90407267 483.60250 200 10 12/8 hole 31.4 90403095 454.60 90407268 500.60250 80 16 12/8 hole 23.0 90413799 367.60 90413800 424.90250 150 16 12/8 hole 19.0 90413801 477.90 90413802 503.10250 200 16 12/12 hole 31.4 90411947 500.60 90411948 641.80300 250 10 12/12 hole 64.0 90403834 586.30 90407269 674.00350 300 10 16/12 hole 33.0 90404226 621.70 90407270 715.60400 80 10 16/8 hole 48.0 90415138 1,134.20 90415136 1,251.50400 350 10 16/16 hole 85.0 90404580 1,377.60 90407271 1,690.30400 80 16 16/8 hole 56.0 90415139 1,290.60 90415137 1,449.50




FITTINGS

VONROLL MMK fittingDouble socket elbow

Version: ECOFIT | HYDROTIGHT socket joint | 5° or 11¼° elbowStandards: EN 545 | Company standardMaterial: Ductile cast iron | Epoxy resin coating in accordance with EN 14 901 and GSK RAL-GZ 662

Figure 2826a DN Deflection[°]

PFAbar

Weight/unitkg


100 5 100 7.8 325139 138.70125 5 64 10.6 325140 191.00150 5 64 13.4 325141 233.70200 5 64 24.9 325142 316.40250 5 50 34.2 325143 640.30300 5 50 43.0 325144 795.20400 5 40 70.0 325224 1,738.50

Note that all prices include TYTON sealing rings and exclude a thrust-resisting ring .

DN Deflection[°]

PFAbar

Weight/unitkg


80 11 100 6.5 325114 115.90100 11 100 7.8 325115 115.90125 11 64 10.6 325116 167.20150 11 64 13.4 325117 173.90200 11 64 24.9 325118 264.10250 11 50 34.2 325119 413.30300 11 50 43.0 325120 520.60350 11 50 44.9 325125 942.40400 11 40 72.0 325121 1,144.80500 11 40 96.0 325122 1,463.00600 11 40 134.0 325123 2,023.50700 11 30 200.0 325124 3,785.80

Figure 2825a




FITTINGS


Version: ECOFIT | HYDROTIGHT socket joint | 22½° or 30° elbowStandards: EN 545 | Company standardMaterial: Ductile cast iron | Epoxy resin coating in accordance with EN 14 901 and GSK RAL-GZ 662


PFAbar

Weight/unitkg


80 22 100 6.7 325088 115.90100 22 100 8.1 325089 118.80125 22 64 11.2 325090 169.10150 22 64 14.2 325091 188.10200 22 64 21.0 325092 272.70250 22 50 30.7 325093 461.70300 22 50 40.4 325094 570.00350 22 50 50.7 325099 1,206.50400 22 40 78.0 325095 1,244.50500 22 40 111.0 325096 2,175.50600 22 40 157.0 325097 2,327.50700 22 30 232.0 325098 3,985.30


DN Deflection[°]

PFAbar

Weight/unitkg


80 30 100 6.8 325062 113.10100 30 100 8.3 325063 119.70125 30 64 11.6 325064 172.90150 30 64 14.8 325065 191.00200 30 64 22.0 325066 288.80250 30 50 32.0 325067 455.10300 30 50 43.2 325068 584.30350 30 50 54.5 325073 1,277.80400 30 40 98.0 325069 1,320.50500 30 40 125.0 325070 1,843.00600 30 40 182.0 325071 2,631.50700 30 30 254.0 325072 4,427.00

Figure 2823a




VONROLL MMQ fittingDouble socket elbow

Version: ECOFIT | HYDROTIGHT socket joint | 90° elbowStandards: EN 545 | Company standardMaterial: Ductile cast iron | Epoxy resin coating in accordance with EN 14 901 and GSK RAL-GZ 662

Fig. 2820a

FITTINGS




PFAbar

Weight/unitkg


80 45 100 7.1 325036 122.60100 45 100 8.8 325037 121.60125 45 64 12.3 325038 178.60150 45 64 15.9 325039 191.00200 45 64 24.6 325040 288.80250 45 50 35.7 325041 439.90300 45 50 48.7 325042 602.30350 45 50 64.9 325047 1,144.80400 45 40 105.0 325043 1,311.00500 45 40 139.0 325044 2,579.30600 45 40 202.0 325045 2,883.30700 45 30 296.0 325046 4,374.80


DN PFAbar

Weight/unitkg


80 100 8.0 325011 136.80100 100 10.2 325012 140.60125 64 14.5 325013 205.20150 64 19.1 325014 235.60200 64 30.5 325015 386.70250 50 45.7 325016 672.60300 50 63.7 325017 894.00350 50 140.0 325022 1,942.80400 40 128.0 325018 1,947.50500 40 230.0 325019 4,721.50600 40 330.0 325020 5,225.00700 30 486.2 325021 5,543.30




FITTINGS

VONROLL MK fittingElbow socketVersion: ECOFIT | HYDROTIGHT socket joint | 11¼° or 22½° elbowStandards: EN 545 | Company standardMaterial: Ductile cast iron | Epoxy resin coating in accordance with EN 14 901 and GSK RAL-GZ 662

Figure 2825 DN Deflection[°]

PFAbar

Weight/unitkg


80 11 100 7.1 325103 106.40100 11 100 8.8 325104 121.60125 11 64 12.1 325105 158.70150 11 64 15.7 325106 197.60200 11 64 24.0 325107 309.70250 11 50 36.2 325801 586.20300 11 50 47.9 325807 763.80400 11 40 111.5 325813 1,472.50

DN Deflection[°]

PFAbar

Weight/unitkg


80 22 100 7.3 325077 110.20100 22 100 9.2 325078 123.50125 22 64 12.7 325079 183.40150 22 64 16.7 325080 200.50200 22 64 25.5 325081 337.30250 22 50 38.8 325802 617.50300 22 50 52.0 325808 780.00400 22 40 120.1 325814 1,524.80

Figure 2824

Note that all prices include a TYTON sealing ring and exclude a thrust-resisting ring .




FITTINGS

VONROLL MK fittingElbow socket

Version: ECOFIT | HYDROTIGHT socket joint | 30° or 45° elbowStandards: EN 545 | Company standardMaterial: Ductile cast iron | Epoxy resin coating in accordance with EN 14 901 and GSK RAL-GZ 662

Figure 2823 DN Deflection[°]

PFAbar

Weight/unitkg


80 30 100 7.4 325051 125.40100 30 100 9.4 325052 125.40125 30 64 13.1 325053 199.50150 30 64 17.2 325054 254.60200 30 64 26.5 325055 353.40250 30 50 40.9 325804 642.20300 30 50 54.9 325809 843.60400 30 40 124.9 325815 1,819.30

DN Deflection[°]

PFAbar

Weight/unitkg


80 45 100 7.7 325025 119.70100 45 100 9.8 325026 130.20125 45 64 13.8 325027 213.80150 45 64 18.3 325028 288.80200 45 64 28.5 325029 389.50250 45 50 44.3 325803 674.50300 45 50 60.5 325810 887.30400 45 40 136.1 325816 1,995.00

Figure 2822





FITTINGS

VONROLL MQ fittingElbow socket


Fig. 2820


DN PFAbar

Weight/unitkg


80 100 10.2 325000 135.90100 100 11.2 325001 154.90125 64 16.1 325002 257.50150 64 21.5 325003 325.90200 64 35.0 325004 457.90



FITTINGS


Version: ECOFIT | HYDROTIGHT socket joint | Branch flange jointStandards: EN 545 | EN 1092-2 | Company standardMaterial: Ductile cast iron | Epoxy resin coating in accordance with EN 14 901 and GSK RAL-GZ 662

Figure 2857 DN1 DN2 PNbar

Weight/unitkg


80 80 10/16/25/40 12.8 325177 206.20100 80 10/16/25/40 14.5 325178 217.60100 100 10/16 15.8 325174 228.00125 80 10/16/25/40 17.9 325290 267.00125 100 10/16 19.3 325175 267.00125 125 10/16 21.6 325176 271.70150 80 10/16/25/40 21.3 325179 308.80150 100 10/16 22.7 325,180 303.10150 125 10/16 30.0 325181 386.70150 150 10/16 27.4 325182 372.40200 80 10/16/25/40 28.6 325183 443.70200 100 10/16 30.4 325184 444.60200 125 10/16 32.0 325291 530.10200 150 10/16 36.1 325185 541.50200 200 16 41.7 325187 549.10250 100 10/16 39.7 325188 613.70250 150 10/16 46.3 325189 708.70250 200 16 42.9 325380 753.40250 250 16 60.5 325191 774.30300 100 10/16 50.0 325192 836.00300 150 10/16 57.0 325193 973.80300 200 16 65.0 325381 1,045.00300 250 16 74.5 325382 1,154.30300 300 16 83.1 325195 1,187.50350 100 10/16 59.3 325305 1,724.30350 200 16 77.0 325307 1,933.30350 300 16 110.0 325309 2,151.80400 100 10/16 72.0 325402 1,724.30400 150 10/16 81.4 325196 1,748.00400 200 16 90.6 325198 1,985.50400 250 16 130.0 325411 2,075.80400 300 16 113.5 325383 2,223.00400 400 16 140.6 325200 2,992.50500 100 10/16 116.0 325201 1,933.30500 150 10/16 141.0 325404 2,156.50500 200 16 141.0 325203 2,308.50500 300 16 182.0 325384 2,935.50500 400 16 205.0 325205 3,358.30500 500 16 247.0 325207 3,975.80

Note that all prices include TYTON sealing rings and exclude a thrust-resisting ring and flange joint parts. PN 10 also available from DN 200.



FITTINGS




Weight/unitkg


600 100 10/16 171.0 325208 3,059.00600 150 10/16 187.0 325405 3,097.00600 200 16 189.0 325210 3,106.50600 250 16 220.0 325412 4,108.80600 300 16 239.0 325413 4,260.80600 400 16 263.0 325212 4,270.30600 500 16 331.0 325414 6,046.80600 600 16 366.0 325214 6,046.80




FITTINGS

VONROLL MMB fittingDouble socket piece with a branched socket

Version: ECOFIT | HYDROTIGHT socket jointStandards: EN 545 | Company standardMaterial: Ductile cast iron | Epoxy resin coating in accordance with EN 14 901 and GSK RAL-GZ 662

Figure 2856


DN1 DN2 PFAbar

Weight/unitkg


80 80 100 11.4 325145 501.60100 80 100 13.1 325149 685.00100 100 100 14.1 325150 224.20125 80 64 16.5 325146 278.40125 100 64 17.8 325151 280.30125 125 64 19.9 325152 292.60150 80 64 19.9 325245 305.00150 100 64 20.9 325153 304.00150 125 64 29.0 325154 368.60150 150 64 25.2 325155 336.30200 80 64 27.2 325246 394.30200 100 64 28.6 325156 444.60200 125 64 31.4 325147 576.70200 150 64 33.4 325157 579.50200 200 64 38.2 325158 651.70250 100 50 37.9 325247 732.50250 125 50 39.9 325248 709.70250 150 50 43.6 325148 832.20250 200 50 49.3 325249 800.90250 250 50 56.0 325159 775.20300 100 50 47.7 325250 926.30300 125 50 48.7 325266 888.30300 150 50 54.3 325251 892.10300 200 50 61.0 325160 1,021.30300 250 50 80.0 325252 1,106.80300 300 50 75.0 325161 1,239.80400 150 40 100.0 325253 5,695.30400 200 40 110.0 325162 5,899.50400 300 40 130.0 325163 6,118.00400 400 40 160.0 325164 7,096.50500 100 40 108.4 325255 6,973.00500 150 40 151.0 325173 7,144.00500 200 40 166.0 325165 7,813.80500 300 40 201.0 325166 7,728.30500 400 40 199.2 325257 7,752.00500 500 40 244.0 325167 7,932.50600 200 40 201.0 325168 8,217.50600 400 40 250.4 325169 8,322.00



FITTINGS

VONROLL UA fitting (T universal sockets, double chamber) Double socket piece with a loose flanged branch



Weight/unitkg


100 50 10/16/25/40 20.0 261000 257.50100 100 10/16 23.0 261002 315.40125 50 10/16/25/40 24.0 261003 325.90125 100 10/16 25.0 261005 359.10150 50 10/16/25/40 27.0 261007 470.30150 100 10/16 28.0 261009 457.00200 50 10/16/25/40 38.0 261012 704.90200 100 10/16 38.0 261014 571.90

Note that all prices include a TYTON sealing ring and exclude a thrust-resisting ring and flange joint parts.

VONROLL UA fitting (T universal sockets, double chamber) Double socket piece with threaded connection pieces

Version: ECOFIT | HYDROTIGHT socket joint | Branch threaded connection piecesStandards: EN 545 | Company standardMaterial: Ductile cast iron | Epoxy resin coating in accordance with EN 14 901 and GSK RAL-GZ 662

Figure 2858 DN1 ET PFAbar

Weight/unitkg


100 2" 100 19.5 325370 462.70125 2" 64 23.5 325371 386.70150 2" 64 26.5 325372 505.40200 2" 64 37.5 325373 652.70




FITTINGS

VONROLL IT fitting Double spigot end piece with a branch spigot end

Version: ECOFIT spigot end joint | Branch spigot endStandards: EN 545 | Company standardMaterial: Ductile cast iron | Epoxy resin coating in accordance with EN 14 901 and GSK RAL-GZ 662

Figure 2859 DN1 DN2 PFAbar

Weight/unitkg


80 80 100 6.5 155324 332.50100 100 100 14.1 155325 403.80150 100 64 23.4 155326 455.10150 150 64 24.3 155327 671.70200 200 64 35.1 155323 812.30



VONROLL MMR fittingDouble socket reduction piece



Weight/unitkg


100 80 100 7.5 325267 134.00125 80 64 9.9 325268 170.10125 100 64 9.8 325269 175.80150 80 64 12.3 325270 260.30150 100 64 12.3 325271 246.10150 125 64 12.6 325272 254.60200 100 64 18.3 325273 279.30200 125 64 18.7 325274 284.10200 150 64 18.7 325275 286.90250 125 50 26.3 325360 523.50250 150 50 26.5 325276 525.40250 200 50 25.8 325277 527.30300 150 50 35.9 325278 530.10300 200 50 35.7 325279 532.00300 250 50 34.6 325280 640.30350 200 50 47.8 325361 2,156.50350 250 50 46.8 325362 2,175.50350 300 50 45.1 325281 2,707.50400 250 40 66.0 325363 1,524.80400 300 40 64.0 325364 1,814.50400 350 40 55.5 325366 2,128.00500 300 40 95.2 325365 3,035.30500 400 40 94.0 325282 3,059.00600 500 40 131.0 325284 3,500.80700 600 30 180.3 325285 4,949.50


FITTINGS



VONROLL U fittingPush-on socket

Version: ECOFIT | HYDROTIGHT socket joint Standards: EN 545 | Company standardMaterial: Ductile cast iron | Epoxy resin coating in accordance with EN 14 901 and GSK RAL-GZ 662

Figure 2870 DN PFAbar

Weight/unitkg


80 100 8.9 261050 202.40100 100 10.8 261051 222.30125 64 13.6 261052 249.90150 64 16.7 261053 325.90200 64 23.0 261054 431.30250 50 31.5 261055 551.00300 50 40.5 261056 707.80350 50 51.0 261057 1,239.80400 40 62.0 261058 2,755.00500 40 90.0 261059 2,831.00

Note that all prices include TYTON sealing rings and exclude a thrust-resisting ring . Internal thread outlet of up to 2" available on request.

FITTINGS



VONROLL flanged socketPush-on flange socket piece

Version: ECOFIT | HYDROTIGHT socket joint | Flange jointStandards: EN 545 | EN 1092-2 | Company standardMaterial: Ductile cast iron | Epoxy resin coating in accordance with EN 14 901 and GSK RAL-GZ 662

Figure 2877b DN PNbar

Weight/unitkg


80 10/16/25/40 9.9 325225 97.90100 10/16 9.1 325226 108.30100 25/40 10.7 325829 169.10125 10/16 12.4 325227 141.60125 25/40 13.2 325830 275.50150 10/16 15.2 325228 164.40150 25 15.9 325831 355.30150 40 18.1 325832 367.70200 16 21.8 325230 243.20200 25 23.0 325833 564.30200 40 26.5 325834 620.40250 16 29.8 325232 337.30250 25 33.7 325835 1,016.50250 40 40.7 325836 1,961.80300 16 36.2 325234 437.00350 16 48.5 325244 929.10400 16 59.0 325236 929.10500 16 89.8 325238 1,534.30600 16 145.0 325240 2,251.50700 16 167.0 325242 8,341.00


FITTINGS



VONROLL E fittingFlange socket piece


Figure 2888

FITTINGS

DN PNbar

Weight/unitkg


100 25/40 15.2 328600 1,320.50100 63 17.7 328601 1,952.30125 25 19.4 328602 1,885.80125 40 19.4 328603 2,094.80125 63 24.3 328604 2,726.50150 25 24.6 328605 2,137.50150 40 24.6 328606 2,365.50150 63 32.8 328607 3,078.00200 25 34.7 328608 2,351.30200 40 37.9 328609 2,598.30200 63 53.1 328610 3,382.00

Note that all prices include a TYTON sealing ring and exclude a thrust-resisting ring and flange joint parts.



FITTINGS

VONROLL F fittingSingle-flange fitting


Figure 2890

Note that all prices exclude flange joint parts. PN 10 also available from DN 200.

DN PNbar


Weight/unitkg


80 10/16/25/40 350 7.8 155340 111.20100 10/16 360 9.7 155341 118.80100 25/40 360 9.7 158611 1,363.30100 63 360 9.7 158613 1,534.30125 10/16 370 12.5 155342 153.00125 25 370 12.5 158614 1,429.80125 40 370 12.5 158615 1,491.50125 63 370 12.5 158616 1,600.80150 10/16 380 16.0 155343 171.00150 25 380 16.0 158617 1,477.30150 40 380 16.0 158618 1,562.80150 63 380 16.0 158619 1,681.50200 16 400 23.0 155345 285.00200 25 400 23.0 158620 1,657.80200 40 400 23.0 158621 1,738.50200 63 400 23.0 158622 1,862.00250 16 420 32.0 155347 390.50300 16 440 42.0 155349 492.10350 16 460 55.3 155339 959.50400 16 480 65.0 155351 1,197.00500 16 520 95.0 155353 1,866.80600 16 560 135.0 155355 3,006.80700 16 600 183.0 155357 4,460.30



VONROLL unions PE-100 S-5for use in water pipes | PFA 16 bar

Version: ECOFIT | HYDROTIGHT socket joint | Transition to a double chamber socket joint for plastic pipelinesStandards: Company standardMaterial: PE-100 S-5

Figure 5468 DN dRmm

dlmm

Lmm

L1mm

Weight/unitkg


80 90 73.6 286 ±3 170 1.5 180565 271.70100 110 90.0 310 ±3 194 2.2 180566 277.40100 125 102.2 330 ±3 214 2.6 180567 283.10125 140 114.6 330 ±3 214 3.8 180568 315.40125 160 130.8 330 ±3 210 4.3 180574 319.20150 160 130.8 354 ±5 234 4.8 180569 321.10150 180 147.2 380 ±5 260 5.1 180570 331.60200 200 163.6 395 ±5 270 8.0 180571 358.20200 225 184.0 413 ±5 288 8.9 180572 459.80200 250 204.6 395 ±5 270 8.6 180573 568.10

Used in connections between gate valves or pipeline components with push-in socket joints (double-chamber system) and plastic pipelines:The socket joint must be equipped with the thrust-resisting ring in Fig. 2807.

FITTINGS



VONROLL plugs for pressure testing



Lmm

Weight/unitkg

Part no. G 1"

Price/unit€

Part no. G 2"

Price/unit€

80 100 250 6.2 452029 424.70 454130 424.70100 100 250 6.4 452030 424.70 454131 424.70125 64 300 10.6 452031 434.20 454132 434.20150 64 300 16.2 452032 436.10 454133 436.10200 64 350 23.6 452033 531.10 454134 531.10250 50 350 38.7 452034 556.70 454135 556.70300 50 400 51.9 452035 572.90 452190 572.90400 40 405 85.4 452053 789.50 452191 789.50

Other DN on request

FITTINGS

VONROLL cap for pressure testing


Fig. 2895 DN PFAbar

Lmm

Weight/unitkg

Part no. G 1"

Price/unit€

Part no. G 2"

Price/unit€

80 100 144 6.0 202036 300.20 204110 300.20100 100 145 7.8 202037 304.00 204111 304.00125 64 153 10.5 202038 301.20 204112 301.20150 64 161 13.5 202039 325.90 204113 325.90200 64 166 20.0 202040 473.10 204114 473.10250 50 171 28.5 202041 485.50 204115 485.50300 50 170 42.5 202042 532.00 204116 532.00350 50 175 58.8 202058 580.50 204121 580.50400 40 190 75.4 202055 652.70 204117 652.70

Other DN on request



ACCESSORIES

VONROLL HYDROTIGHT thrust-resisting ring(external), for fittings


Figure 2805 DN Pipe class PFAbar

DFmm

QuantityBolts

Weight/unitkg


400 C40 25 595 16 47.1 201022 902.50500 K9 25 710 16 58.6 201023 1,192.30600 K9 25 833 20 92.3 262024 1,339.50700 K9 25 962 24 145.5 262025 1,448.80



ACCESSORIES

VONROLL HYDROTIGHT thrust-resisting ring(external, electrically non-conductive)


Figure 2806 DN Pipe class PFAbar

DFmm

QuantityBolts

Weight/unitkg


80 C100 40 235 3 4.7 262000 112.10100 C100 40 256 3 5.1 262001 83.60125 C64 40 287 3 5.7 262002 93.60150 C64 40 310 4 6.9 262003 113.10200 C64 16 325 3 8.9 262004 155.80200 C64 40 325 6 10.1 262008 169.10250 C50 16 421 4 13.9 262005 217.60250 C50 40 421 8 15.5 262009 230.90300 C50 16 479 5 19.6 262006 256.50300 C50 40 479 10 21.6 262010 275.50350 C40 16 534 5 25.5 262007 440.80350 C40 25 534 10 27.5 262011 453.20400 C40 16 595 14 39.1 262012 627.00500 K9 10 710 16 52.4 262013 964.30600 K9 10 826 24 61.0 262031 1,477.30

Higher pressures available on request. External thrust-resisting ring for push-in socket joint with an oblique suppor-ting collar. Epoxy-coated thrust-resisting ring



ACCESSORIES

VONROLL connection set for plastic pipes made of PE and PVC

Version: ECOFIT | HYDROTIGHT socket jointStandards: Company standardMaterial: Ductile cast iron | Epoxy resin coating in accordance with EN 14 901 and GSK RAL-GZ 662


dRmm

DFmm

Weight/unitkg


80 16 90 235 5.0 180584 348.70100 16 110 256 5.5 180585 372.40125 16 125 287 6.7 180586 479.80125 16 140 287 5.9 180587 375.30150 16 160 310 7.6 180588 478.80200 16 200 325 13.0 180589 800.90200 16 225 325 12.0 180590 682.10

External thrust-resisting ring for push-in socket joint with an oblique supporting collar



ACCESSORIES

VONROLL seal with a HYDROTIGHT thrust-resisting ringfor water (internal)

Version: ECOFIT | HYDROTIGHT socket jointStandards: EN 545 | Company standard | DIN 28 603Material: EPDM | Stainless steel toothed segments

Figure 2504-S DN Pipe class PFAbar

Weight/unitkg


80 C100 32 0.2 452149 58.40100 C100 32 0.2 452150 63.20125 C64 16 0.3 452151 69.40150 C64 16 0.3 452152 89.30200 C64 16 0.5 452153 118.80250 C50 16 0.7 452154 151.10300 C50 16 1.0 452155 211.90350 C40 16 1.3 452156 305.00400 C40 10 1.6 452157 329.70500 K9 10 2.4 452158 461.70600 K9 10 3.0 452160 596.60

PFA information only applies to DUCPUR and CEMPUR pipes.Reduced PFA for ECOPUR and ECOCEM pipes following consultation with our Technical Support team.Seal in accordance with DIN 28 603



ACCESSORIES

VONROLL HYDROTIGHT thrust-resisting ring(internal) for double chamber, standard, electrically non-conductive

Version: ECOFIT | HYDROTIGHT socket jointStandards: EN 545 | Company standardMaterial: EPDM | Stainless steel toothed segments

Figure 2807B

VONROLL HYDROTIGHT thrust-resisting ring(internal) for double chamber | for higher pressures (up to DN 300) and pipes with DN 350 to DN 400

Version: ECOFIT | HYDROTIGHT socket jointStandards: EN 545 | Company standardMaterial: EPDM | Stainless steel toothed segments

Fig. 2807A DN Pipe class PFAbar

Weight/unitkg


80 C100 40 0.20 465440 48.90100 C100 40 0.30 465441 52.70125 C64 40 0.30 465442 61.80150 C64 40 0.40 465443 78.40200 C64 40 0.60 465444 117.80250 C50 25 0.70 465445 138.70300 C50 25 0.80 465446 166.30350 C40 16 1.30 465435 325.90400 C40 16 1.40 465447 380.00

DN Pipe class PFAbar

Weight/unitkg


80 C100 25 0.15 465450 44.20100 C100 25 0.25 465451 47.50125 C64 25 0.25 465452 55.10150 C64 25 0.30 465453 70.30200 C64 25 0.40 465454 106.40250 C50 16 0.50 465455 124.50300 C50 16 0.60 465456 150.10



ACCESSORIES

VONROLL HYDROTIGHT sealFor water

Version: ECOFIT | HYDROTIGHT socket jointStandards: EN 681-1 | Company standard | DIN 28 603Material: EPDM

Figure 2810 DN Weight/unitkg


80 0.10 454976 7.00100 0.10 454963 8.40125 0.20 454964 9.80150 0.20 454965 11.10200 0.30 454966 16.50250 0.50 454967 21.90300 0.60 454968 28.70350 0.80 454969 34.20400 1.00 454970 41.00500 1.60 451014 114.00600 2.20 451015 150.10700 3.10 451017 170.10

VONROLL HYDROTIGHT sealFor gas

Version: ECOFIT | HYDROTIGHT socket jointStandards: EN 682 | Company standard | DIN 28 603Material: NBR

Fig. 2811 DN Weight/unitkg


80 0.10 454152 12.40100 0.10 454153 13.90125 0.20 454154 17.80150 0.20 454155 20.80200 0.30 454156 28.90250 0.50 454157 36.70300 0.60 454158 48.00350 0.80 454159 53.70400 1.00 454160 55.10500 1.60 454161 94.10600 2.20 454162 134.00700 3.10 454163 151.10



Figure 2326a

FITTINGS

VONROLL MMK fitting DUCPUR SCREW SOCKETDouble socket elbow screw sockets 5°

Version: Screw-gland socket joint | 5° elbow | Standard version with electrical bridgingStandards: EN 545 | Company standardMaterial: Ductile cast iron | Bitumen outside coating | Epoxy resin coating lining

DN PFAbar

Weight/unitkg


100 40 21.0 206018 219.50125 40 28.0 206019 278.40150 40 35.5 206020 354.40200 40 52.4 206021 531.10250 25 81.0 206022 978.50300 25 78.0 206023 1,320.50


Version: Screw-gland socket joint | 11¼° elbow | Standard version with electrical bridgingStandards: EN 545 | Company standardMaterial: Ductile cast iron | Bitumen outside coating | Epoxy resin coating lining

Figure 2325a DN PFAbar

Weight/unitkg


80 40 16.2 205993 191.90100 40 12.3 205994 209.00125 40 16.7 205995 267.00150 40 20.9 205996 354.40200 40 52.2 205997 531.10250 25 80.5 205998 843.30300 25 81.0 205999 1,064.00





FITTINGS


Version: Screw-gland socket joint | 22½° elbow | Standard version with electrical bridgingStandards: EN 545 | Company standardMaterial: Ductile cast iron | Bitumen outside coating | Epoxy resin coating lining


Weight/unitkg


80 40 16.9 205961 191.90100 40 12.7 205962 210.90125 40 17.4 205963 268.90150 40 22.1 205964 351.50200 40 57.0 205965 531.10250 25 81.4 205966 849.30300 25 114.8 205967 1,064.00




Weight/unitkg


80 40 17.4 205937 185.30100 40 23.7 205938 208.10125 40 30.9 205939 267.90150 40 40.0 205940 351.50200 40 59.7 205941 526.30250 25 86.5 205942 849.30300 25 72.6 205943 1,064.00





FITTINGS



DN PFAbar

Weight/unitkg


80 40 18.7 205913 185.30100 40 13.3 205914 215.70125 40 18.5 205915 270.80150 40 23.2 205916 349.60200 40 65.5 205917 518.70250 25 91.5 205918 838.90300 25 99.5 205919 1,054.50

Figure 2322a

VONROLL MMQ fitting DUCPUR SCREW SOCKETDouble socket elbow screw sockets 90°



Weight/unitkg


80 40 18.7 205888 206.20100 40 14.8 205890 238.50125 40 20.4 205891 316.40150 40 27.0 205892 404.70200 40 69.9 205893 654.60250 25 95.0 205894 1,030.80300 25 72.0 205895 1,334.80





FITTINGS

VONROLL MK fitting DUCPUR SCREW SOCKETElbow socket screw socket 5°



Weight/unitkg


80 40 11.5 206005 164.40100 40 14.8 206006 164.40125 40 20.6 206007 220.40150 40 26.1 206008 291.70200 40 41.0 206009 475.00250 25 58.2 206010 821.80300 25 61.9 206011 1,230.30


Version: Screw-gland socket joint | 11¼° elbow | Standard version with electrical bridgingStandards: EN 545 | Company standardMaterial: Ductile cast iron | Bitumen outside coating | Epoxy resin coating lining


Weight/unitkg


80 40 11.4 205973 144.40100 40 15.1 205974 164.40125 40 20.2 205975 221.40150 40 26.2 205976 299.30200 40 41.1 205977 475.00250 25 57.0 205978 821.80300 25 59.0 205979 1,230.30





FITTINGS


Version: Screw-gland socket joint | 22½° elbow | Standard version with electrical bridgingStandards: EN 545 | Company standardMaterial: Ductile cast iron | Bitumen outside coating | Epoxy resin coating lining

DN PFAbar

Weight/unitkg


80 40 12.2 205949 148.20100 40 16.4 205950 164.40125 40 22.2 205951 229.90150 40 28.9 205952 302.10200 40 44.5 205953 475.00250 25 67.5 205954 821.80300 25 94.5 205955 1,230.30

Figure 2324




Weight/unitkg


80 40 13.1 205925 153.00100 40 18.3 205926 164.40125 40 23.1 205927 230.90150 40 30.7 205928 304.00200 40 48.0 205929 475.00250 25 69.0 205930 863.60300 25 44.0 205931 1,230.30





FITTINGS




Weight/unitkg


80 40 9.7 205901 152.00100 40 20.3 205902 169.10125 40 25.4 205903 233.70150 40 34.0 205904 305.00200 40 55.0 205905 475.00250 25 78.5 205906 855.00300 25 116.5 205907 1,220.80

VONROLL MQ fitting DUCPUR SCREW SOCKETElbow socket screw socket 90°



Weight/unitkg


80 40 10.7 205876 171.00100 40 18.5 205877 190.00125 40 26.3 205878 280.30150 40 35.0 205879 359.10200 40 56.5 205880 578.60250 25 92.0 205881 1,358.50300 25 132.0 205882 2,118.50





FITTINGS

VONROLL MB fitting DUCPUR SCREW SOCKETSocket head end piece screw socket with a 90° branched socket

Version: Screw-gland socket joint | Branched screw-gland socket joint | Standard version with electrical bridgingStandards: EN 545 | Company standardMaterial: Ductile cast iron | Bitumen outside coating | Epoxy resin coating lining

DN1 DN2 PFAbar

Weight/unitkg


80 80 40 22.6 206029 305.00100 100 40 23.7 206033 301.20125 100 40 38.1 206037 358.20125 125 40 42.0 206038 386.70150 100 40 47.0 206042 443.70150 150 25 55.0 206043 486.40200 100 25 70.5 206044 1,144.80

Figure 2350


VONROLL MA fitting DUCPUR SCREW SOCKETSocket head end piece with a 90° flanged branch

Version: Screw-gland socket joint | Branch flange joint | Standard version with electrical bridgingStandards: EN 545 | Company standard | EN 1092-2Material: Ductile cast iron | Bitumen outside coating | Epoxy resin coating lining


Weight/unitkg


80 80 10/16/25/40 20.9 206062 268.90100 40 10/16/25/40 23.0 206063 275.50100 100 10/16 27.6 206064 305.00125 40 10/16/25/40 38.6 206065 362.90125 100 10/16 35.9 206066 387.60125 125 10/16 37.4 206067 402.80150 100 10/16 44.6 206069 427.50150 150 10/16 49.5 206070 476.00200 100 10/16 67.0 206071 738.20200 200 16 76.2 206085 908.20

All prices include a set of screws and a seal. Version not electrically bridged on request.Flanged branch DN 200 also available in PN 10.



FITTINGS

VONROLL T fitting universal (UA) DUCPUR SCREW SOCKETDouble socket piece with a loose flanged branch

Version: Screw-gland socket joint | Universal branch (UA) | Standard version with electrical bridgingStandards: EN 545 | Company standard | EN 1092-2Material: Ductile cast iron | Bitumen outside coating | Epoxy resin coating lining


Weight/unitkg


100 50 10/16/25/40 17.3 206094 369.60100 80 10/16/25/40 19.1 206095 388.60100 100 10/16 20.1 206097 381.00125 50 10/16/25/40 22.1 206098 444.60125 80 10/16/25/40 24.0 206099 462.70125 100 10/16 24.7 206100 474.10125 125 10/16 27.1 206101 511.10150 50 10/16/25/40 25.3 206102 452.20150 80 10/16/25/40 27.7 206103 559.60150 100 10/16 27.8 206104 512.10150 125 10/16 30.7 206105 650.80150 150 10/16 33.9 206106 672.60200 50 10/16/25/40 36.9 206107 637.50200 80 10/16/25/40 37.1 206108 695.40200 100 10/16 38.1 206109 643.20200 125 10/16 41.5 206110 793.30200 150 10/16 46.5 206111 876.90200 200 10 49.5 206112 938.60




FITTINGS

VONROLL MMB fitting DUCPUR SCREW SOCKETDouble socket piece screw socket with a 90° branched socket

Version: Screw-gland socket joint | Branched screw-gland socket joint | Standard version with electrical bridgingStandards: EN 545 | Company standardMaterial: Ductile cast iron | Bitumen outside coating | Epoxy resin coating lining

DN1 DN2 PFAbar

Weight/unitkg


80 80 40 25.4 206117 283.10100 100 40 34.1 206119 317.30125 100 40 41.7 206121 374.30125 125 40 46.0 206122 400.90150 100 40 52.0 206124 490.20150 150 40 60.0 206125 561.50200 100 40 70.0 206126 690.70200 200 40 91.1 206127 818.00250 100 25 107.0 206128 959.50250 250 25 133.1 206130 1,567.50

Figure 2356


VONROLL MMA fitting DUCPUR SCREW SOCKETDouble socket piece screw socket with a 90° flanged branch

Version: Screw-gland socket joint | Branch flange joint | Standard version with electrical bridgingStandards: EN 545 | Company standard | EN 1092-2Material: Ductile cast iron | Bitumen outside coating | Epoxy resin coating lining


Weight/unitkg


80 80 10/16/25/40 23.7 206143 278.40250 100 10/16 54.4 206147 921.50250 250 16 77.4 206160 1,154.30300 300 16 126.0 206162 1,444.00




FITTINGS

VONROLL T fitting installation, push-on DUCPUR SCREW SOCKETT fitting with a screw socket, flange and a 90° flanged branch

Version: Screw-gland socket joint | Flange joint | Standard version with electrical bridgingStandards: EN 545 | Company standard | EN 1092-2Material: Ductile cast iron | Bitumen outside coating | Epoxy resin coating lining

Figure 2377a DN1 DN2 PNbar

Weight/unitkg


80 80 10/16/25/40 22.7 206232 323.00100 100 10/16 20.1 206235 309.70125 100 10/16 25.2 206238 369.60125 125 10/16 27.0 206239 422.80150 100 10/16 29.3 206242 484.50150 150 10/16 32.7 206243 539.60200 100 10 61.6 206244 721.10200 100 16 61.6 207303 721.10200 150 10 61.7 206245 780.90200 150 16 61.7 207304 780.90250 100 10 79.7 206246 867.40250 100 16 79.7 207305 867.40250 150 10 85.7 206247 921.50250 150 16 85.7 207306 921.50




FITTINGS

VONROLL R fitting DUCPUR SCREW SOCKETScrew socket reduction piece at spigot end

Version: Screw-gland socket joint | Spigot end | Standard version with electrical bridgingStandards: EN 545 | Company standardMaterial: Ductile cast iron | Bitumen outside coating | Epoxy resin coating lining

DN1 DN2 PFAbar

Weight/unitkg


100 80 40 8.2 206292 181.50125 100 40 10.6 206297 250.80150 100 40 11.5 206300 257.50150 125 40 14.0 206301 277.40200 150 40 18.1 206304 425.60

Figure 2382

VONROLL MMR fitting DUCPUR SCREW SOCKETDouble socket reduction piece screw socket

Version: Screw-gland socket joint | Standard version with electrical bridgingStandards: EN 545 | Company standardMaterial: Ductile cast iron | Bitumen outside coating | Epoxy resin coating lining


Weight/unitkg


125 80 40 14.7 323274 278.40125 100 40 15.2 323275 293.60200 100 40 25.8 323279 422.80200 125 40 27.6 323280 443.70200 150 40 28.2 323281 446.50





FITTINGS

VONROLL/DUKTUS MMR fittingDouble socket reduction piece | PFA 16 bar

Version: Screw-gland socket jointStandards: EN 545 | Company standardMaterial: Ductile cast iron | Epoxy resin coating in accordance with EN 14 901 and GSK RAL-GZ 662 or external bitu-


DN1 DN2 Weight/unitkg



125 80 9.3 90407193 239.30 90407194 261.00125 100 10.0 90400648 249.10 90400691 274.70200 100 18.3 90400701 331.00 90400693 142.50200 125 18.7 90407195 344.20 90400694 395.60200 150 27.5 90400656 348.60 90400696 402.20

All prices include a set of screws and a seal.




FITTINGS

VONROLL U fitting DUCPUR SCREW SOCKETPush-on sockets



Weight/unitkg


40 40 6.5 201918 141.6050 40 7.2 206182 169.1065 40 9.7 206183 173.9080 40 11.2 206184 164.40

100 40 14.3 206185 191.90125 40 18.0 206187 230.90150 40 22.2 206188 272.70200 40 33.2 206189 400.90250 25 45.4 206190 660.30300 25 57.6 206191 805.60




Figure 8374DN

PNbar

Weight/unitkg

Part no. Price/unit€ Part no.

Price/unit€

80 10/16 8.2 90403940 109.10 90401372 109.50100 10/16 9.5 90402842 118.90 90401436 123.40125 10/16 12.5 90401173 147.20 90401174 157.10150 10/16 15.0 90401990 180.60 90401991 185.00200 10 21.5 90403074 226.60 90402089 241.10200 16 21.5 90404885 244.90 90414513 256.20250 10 29.0 90403035 327.10 90402224 288.70250 16 29.0 90409666 349.80 90415705 383.90300 10 36.0 90402366 424.20 90402001 462.00300 16 36.0 90405892 451.30 90403075 520.60400 10 57.1 90403704 778.20 90402984 841.20400 16 57.1 90406926 852.60 90409397 930.10


All prices include a set of screws and a seal and exclude flange joint parts.

FITTINGS

VONROLL flanged socket DUCPURPush-on flange socket piece

Version: Screw-gland socket joint | Flange joint | Standard version with electrical bridgingStandards: EN 545 | Company standard | EN 1092-2Material: Ductile cast iron | Bitumen outside coating | Epoxy resin coating lining

DN PFAbar

Weight/unitkg


80 10/16/25/40 10.5 206257 191.00100 10/16 14.4 206258 194.80125 10/16 19.5 206259 248.00150 10/16 23.9 206260 285.00200 16 29.2 206623 477.90250 16 37.5 206624 696.40300 16 47.6 206625 1,420.30

Figure 2377b

All prices include a set of screws and a seal but exclude flange joint parts. Version not electrically bridged on request. PN 10 also available from DN 200.


Version: Screw-gland socket joint | Flange jointStandards: EN 545 | EN 1092-2 | Company standard | EN 14 901Material: Ductile cast iron | Epoxy resin coating or external bitumen and internal enamel



FITTINGS

VONROLL/DUTKUS MMB fittingDouble socket piece with a branched socket | PFA 16 bar

Version: Screw-gland socket joint | Branched screw-gland socket jointStandards: EN 545 | Company standard | EN 14 901Material: Ductile cast iron | Epoxy resin coating or external bitumen and internal enamel




125 40 15.1 90407127 400.60 90407128 426.40125 80 17.0 90407129 408.60 90400777 446.40125 100 18.3 90407130 415.90 90400644 444.90125 125 19.9 90407132 432.30 90400646 461.60150 40 18.3 90407133 420.10 90407134 447.20150 80 19.9 90407136 426.20 90400779 464.00150 100 21.0 90410410 434.80 90410412 403.60150 150 25.0 90407135 463.10 90400778 500.90200 40 26.0 90407139 475.50 90407140 514.50200 80 28.0 90407146 486.60 90400807 535.10200 100 29.5 90407147 502.10 90407148 553.80200 150 33.5 90405825 551.30 90407149 624.30200 200 38.0 90407150 574.50 90407151 653.90


All prices include sets of screws and seals.



FITTINGS

VONROLL/DUKTUS U fittingPush-on sockets | PFA 16 bar

Version: Screw-gland socket jointStandards: EN 545 | Company standard | EN 14 901Material: Ductile cast iron | Epoxy resin coating or external bitumen and internal enamel

DN Weight/unitkg



80 9.0 90403917 193.90 90401927 195.40100 11.0 90404330 208.20 90402033 212.00125 13.5 90401994 256.70 90402363 274.90150 17.5 90403025 298.20 90401409 314.60200 24.0 90402137 359.90 90402075 414.70250 30.0 90402782 540.10 90402763 598.90300 40.5 90403037 625.10 90404221 709.60400 62.5 90405155 1,031.20 90404496 1,083.40


All prices include sets of screws and seals.



FITTINGS


Version: Screw-gland socket joint | 11¼° or 22½° elbowStandards: EN 545 | Company standard | EN 14 901Material: Ductile cast iron | Epoxy resin coating or external bitumen and internal enamel

DN Deflection[°]

Weight/unitkg



200 11 19.2 90400876 358.00 90400891 390.70


DN Deflection[°]

Weight/unitkg



200 22 21.9 90400878 362.40 90400893 408.40





DN Deflection[°]

Weight/unitkg



200 45 24.5 90400882 395.20 90400897 450.60


Version: Screw-gland socket joint | 30° or 45° elbowStandards: EN 545 | Company standard | EN 14 901Material: Ductile cast iron | Epoxy resin coating or external bitumen and internal enamel

DN Deflection[°]

Weight/unitkg



200 30 23.9 90400880 368.10 90400895 416.60




FITTINGS



FITTINGS

VONROLL mounting pipe DUCPUR screw socket


Figure 2389 DN Lmm

PFAbar

Weight/unitkg


100 300 40 11.0 206342 139.70125 300 40 14.6 206343 164.40150 300 40 18.5 206344 238.50200 350 40 30.0 206345 267.90




FITTINGS

VONROLL threaded connecting pieceto the screwed-socket joint

Version: Screw-gland socket joint | Standard version with electrical bridgingStandards: EN 545 | Company standardMaterial: Ductile cast iron | Bitumen outside coating | Bitumen lining

DN G Weight/unitkg


40 1 ¼” 0.9 452207 51.8050 1 ¼” 1.2 452208 70.3050 1 ½” 1.2 452209 70.3065 1 ½” 2.0 452210 110.2065 2” 2.0 452211 110.2080 1 ½” 2.4 452212 115.9080 2” 2.5 452213 115.90

100 2” 3.2 452215 124.50100 3” 3.3 452216 124.50125 2” 4.3 452217 134.00125 3” 4.3 452218 134.00

Figure 2392

VONROLL closing plugsfor the screwed-socket joint


Figure 2393 DN G Weight/unitkg


80 0½” 0.9 452222 64.10100 0½” 1.2 452223 66.00125 1” 1.2 452224 74.10150 1 ¼” 2.0 452225 83.10200 2” 2.0 452226 101.70





FITTINGS

VONROLL sealing capfor the screwed-socket joint


Figure 2395 DN G Weight/unitkg


40 1 ¼” 3.7 202231 67.9050 1 ¼” 4.3 202232 83.1065 1 ¼” 5.4 202233 97.9080 1 ¼” 6.0 202234 120.70

100 1 ¼” 8.2 202235 126.40125 1 ½” 11.0 202236 165.30150 1 ½” 14.5 202237 219.50200 2” 22.7 202238 322.10250 2” 38.5 202239 470.30300 2” 51.5 202240 611.80

VONROLL short thrust-resisting ringComplete grooved clamp

Version: Screw-gland socket jointStandards: Company standardMaterial: Ductile cast iron | Bolts, nuts, galvanised steel washers


Weight/unitkg


40 16 0.82 451169 42.3050 16 1.02 451170 49.90

65/70 16 1.42 451171 92.2080 16 1.52 451172 69.40

100 16 1.86 451173 74.10125 16 1.66 451174 97.90150 16 3.04 451175 134.90200 16 4.86 451176 215.70250 10 9.84 451177 362.00300 10 14.64 451178 496.90





FITTINGS

VONROLL threaded ringshort

Version: Screw-gland socket joint | Standard version with electrical bridgingStandards: Company standardMaterial: Ductile cast iron

DN Weight/unitkg


40 0.90 153000 18.1050 1.00 153001 18.1065 1.30 153002 24.9080 1.40 153003 29.70

100 1.80 153004 31.00125 2.40 153005 35.30150 3.10 153006 48.50200 4.70 153007 64.60250 7.20 153008 90.70300 9.60 153009 120.70

Figure 2310-1

VONROLL contact ringDia. profile

Version: Screw-gland socket jointStandards: Company standardMaterial: Chromated steel

Figure 2310-2 DN Weight/unitkg


40 0.04 452414 6.0050 0.05 452415 6.0065 0.09 452416 7.4080 0.12 452417 7.40

100 0.15 452418 8.40125 0.18 452419 8.40150 0.22 452420 10.50200 0.44 452421 12.30250 0.54 452422 14.10300 0.62 452423 15.60



FITTINGS

VONROLL threaded ringlong

Version: Screw-gland socket jointStandards: Company standardMaterial: Ductile cast iron



80 1.4 153016 37.30100 1.9 153017 39.30125 2.7 153018 43.70150 3.2 153019 59.90200 4.5 153020 77.40250 6.3 153021 105.50300 8.1 153022 136.80



FITTINGS

VONROLL back-up ring profile

Version: Screw-gland socket jointStandards: Company standardMaterial: Chromated steel



40 0.05 452426 6.3050 0.06 452427 6.3065 0.07 452428 8.4080 0.11 452429 8.40

100 0.13 452430 9.00125 0.18 452431 9.00150 0.19 452432 11.60200 0.44 452433 13.80250 0.70 452434 14.80300 0.80 452435 16.20

VONROLL EPDM seal

Version: Screw-gland socket jointStandards: Company standardMaterial: EPDM



40 0.10 452438 6.8050 0.10 452439 7.5065 0.10 452440 8.4080 0.10 452441 8.40

100 0.20 452442 9.70125 0.20 452443 12.00150 0.20 452444 14.30200 0.40 452445 19.80250 0.50 452446 26.70300 0.60 452447 32.70



FITTINGS

VONROLL NBR seal

Version: Screw-gland socket jointStandards: Company standardMaterial: NBR

DN Weight/unitkg


40 0.1 452367 7.4050 0.1 452368 8.4065 0.1 452369 9.2080 0.1 452450 9.20

100 0.2 452451 11.60125 0.2 452452 14.60150 0.2 452453 18.00200 0.4 452454 24.10250 0.5 452455 33.20300 0.6 452456 40.00

Figure 2310-G-4

VONROLL EPDM sealpressed out

Version: Screw-gland socket jointStandards: Company standardMaterial: EPDM

Figure 2310m4 DN Weight/unitkg


40 0.1 457285 72.2050 0.1 457286 72.2060 0.1 457287 72.2070 0.1 457288 72.2075 0.1 457289 72.2080 0.1 457290 72.20

100 0.2 457291 78.90125 0.2 457292 87.40150 0.2 457293 93.10200 0.4 457295 103.60250 0.5 457296 114.00300 0.6 457297 124.50



FITTINGS

VONROLL transition piece PE-100 S-5On vonRoll cast-iron screwed sockets | PN 16

Version: Screw-gland socket jointStandards: Company standardMaterial: PE-100 S-5

DN dRmm

Weight/unitkg


40 50 0.27 451591 157.7050 63 0.41 451592 117.80

65 (70) 75 0.71 451593 196.7080 90 1.00 451594 196.70

100 110 2.27 451595 206.20125 125 2.45 451596 328.70125 140 2.14 451597 259.40150 160 3.05 451598 375.30200 200 5.56 451599 487.40

Figure 2398

VONROLL transition piece PE-100 S-5On vonRoll cast-iron screwed sockets, including a pre-fitted threaded ring | PN 16

Version: Screw-gland socket jointStandards: Company standardMaterial: PE-100 S-5

Figure 2399 DN dRmm

Weight/unitkg


100 125 4.65 451600 259.40100 160 4.99 451601 380.00125 160 7.46 451602 384.80150 180 8.90 451603 466.50200 225 13.30 451604 631.80



FITTINGS

VONROLL/DUKTUS PE F fittingTransition flange on a polyethylene pipe

Version: Flange jointStandards: Company standard | EN 1092-2Material: Ductile cast iron | Epoxy resin coating in accordance with EN 14 901 and GSK RAL-GZ 662 or enamel

EPOXY ENAMEL

DN d PNbar




80 90 10/16 SDR 11 6.0 90408533 175.90 90410455 169.5280 90 10/16 SDR 17 6.0 90403355 175.90 90410459 169.45

100 110 10/16 SDR 11 7.7 90403357 197.30 90410463 196.38100 110 10/16 SDR 17 7.7 90403363 197.30 90410467 196.36100 125 10/16 SDR 11 7.7 90412268 213.70 90410789 224.34100 125 10/16 SDR 17 7.7 90412593 213.70 90412592 217.62150 160 10/16 SDR 11 12.9 90408534 278.00 90410473 295.23150 160 10/16 SDR 17 12.9 90403365 278.00 90410477 295.86150 180 10/16 SDR 11 14.0 90410481 295.10 90410489 309.72150 180 10/16 SDR 17 14.0 90410485 295.10 90410493 309.72200 225 10 SDR 11 24.3 90410497 435.70 90410501 437.44200 225 10 SDR 17 24.3 90403802 435.70 90410505 437.64




FITTINGS

VONROLL/DUKTUS E KS fittingFlange socket piece for PVC pressure pipes


EPOXY ENAMEL

DN d PNbar

Weight/unitkg



80 90 10/16 4.6 90404262 49.80 90410251 60.5010 110 10/16 5.7 90401960 56.10 90410252 69.40

125 140 10/16 7.4 90405413 65.60 90410253 82.60150 160 10/16 9.6 90401962 79.40 90410254 104.00200 225 10 15.5 90404506 129.20 90410255 187.90200 225 16 16.1 90402299 146.30 90410801 191.00250 280 10 24.5 90404710 207.40 90410256 261.70250 280 16 25.3 90407920 231.40 90410802 302.00300 315 10 31.5 90403602 249.00 90410257 343.60300 315 16 37.0 90408304 269.80 90410803 370.70




FITTINGS

VONROLL/DUKTUS F KS fittingFlange head end piece for PVC pressure pipes


EPOXY ENAMEL

DN d PNbar

Weight/unitkg



80 90 10/16 5.0 90404263 60.20 90410804 78.80100 110 10/16 6.6 90404265 69.70 90410805 90.80150 160 10/16 10.5 90404267 105.60 90410806 143.10200 225 10 26.5 90404268 187.90 90410807 257.90200 225 16 26.4 90405301 224.50 90415627 291.30300 315 10 31.0 90404711 299.50 90410808 389.60300 315 16 31.0 90405340 352.40 90415704 459.00




FITTINGS

VONROLL/DUKTUS MMA KS fittingDouble socket piece with a flanged branch for PVC pressure pipes

Version: Flange jointStandards: Company standard | EN 1092-2

DN1 DN2 PNbar

Weight/unitkg


80 80 10 9.1 90405248 111.0080 80 16 9.1 90410812 149.40

100 80 10 15.6 90404269 112.90100 80 10 15.6 90410810 173.40100 100 16 13.5 90405359 133.00100 100 16 13.5 90410811 179.70150 80 10 14.5 90404270 157.00150 80 10 14.5 90410813 203.60150 100 10 16.0 90404472 162.70150 100 16 16.0 90410814 209.30150 150 16 25.1 90404474 176.50150 150 16 25.1 90410815 263.50




FITTINGS

VONROLL/DUKTUS SI 45 tapping saddle 45° – Wastewater

Version: Smooth, ductile wastewater pipes which are suitable for the socket | incl. seal and boltsStandards: EN 598 | Company standard | EN 14 901Material: Ductile cast iron | Epoxy resin coating of at least 250 µm | NBR seal | Corrosion-resistant steel bolts



250-300 150 10.8 0106030026 316.90



FITTINGS

VONROLL/DUKTUS SM 45 tapping saddle 45° – Wastewater

Version: Push-in socket L spigots which are suitable for stoneware pipes | incl. pot seal and boltsStandards: EN 598 | Company standard | EN 14 901Material: Ductile cast iron | Epoxy resin coating of at least 250 µm | NBR seal | Corrosion-resistant steel bolts



250-300 150 10.3 0106030025 330.90350-400 150 9.3 0106030288 330.90



FITTINGS


Version: Smooth, ductile wastewater pipes which are suitable for the socket | incl. seal and boltsStandards: EN 598 | Company standard | EN 14 901Material: Ductile cast iron | Epoxy resin coating of at least 250 µm | NBR seal | Corrosion-resistant steel bolts



250-300 150 8.5 0106010472 181.70400-600 150 8.3 0106010480 237.70

700-1.200 150 7.6 0106010488 237.70300 200 12.9 0106011455 261.00350 200 12.5 0106018762 261.00400 200 12.0 0106011457 261.00

500-600 200 11.1 0106011458 261.00700-800 200 10.5 0106011460 261.00

900-1.200 200 10.0 0106011462 261.00



FITTINGS


Version: Smooth, stoneware pipes which are suitable for the socket | incl. seal and boltsStandards: EN 598 | Company standard | EN 14 901Material: Ductile cast iron | Epoxy resin coating of at least 250 µm | NBR seal | Corrosion-resistant steel bolts



250-300 150 8.5 016013513 181.70400-600 150 8.3 016013521 237.70

700-1.200 150 7.6 016013529 237.70300 200 12.9 016009782 261.00350 200 12.0 016026368 261.00400 200 12.0 016009960 261.00

500-600 200 12.1 016010485 261.00700-800 200 10.5 016009893 261.00

900-1.200 200 10.0 016009974 261.00



FITTINGS

VONROLL/DUKTUS SM 90 tapping saddle 90° – Wastewater

Version: Push-in socket L spigots which are suitable for stoneware pipes | incl. pot seal and boltsStandards: EN 598 | Company standard | EN 14 901Material: Ductile cast iron | Epoxy resin coating of at least 250 µm | NBR seal | Corrosion-resistant steel bolts



250-300 150 9.4 0106011465 230.70350 150 8.5 0106030024 230.70

400-600 150 8.5 0106011467 230.70700-1.200 150 8.6 0106011468 261.00



FITTINGS

VONROLL/DUKTUS for tapping saddles

Version: AccessoriesStandards: EN 598 | Company standard | EN 14 901Material: Ductile cast iron | Epoxy resin coating of at least 250 µm | NBR seal | Corrosion-resistant steel bolts

DN1 DN2 Description Weight/unitkg


350-1.200 150 Saddle seal for tapping saddle 0.1 0700900243 51.30250-300 150 Saddle seal for tapping saddle 0.1 0700900240 51.30300-350 200 Saddle seal for tapping saddle 0.1 0700900241 51.30

400-1.200 200 Saddle seal for tapping saddle 0.1 0700900241 51.30Bolt set (two units M10 x 55) 0.1 0700901000 74.60Bolt set (two units M10 x 70) 0.1 0700903109 79.20

Pot seal for stoneware 0.1 0700900199 62.4013 mm carbide drill 0.1 0700903471 143.50

VONROLL/DUKTUS for tapping saddlesFlexible stainless steel clamp GR 220

Version: AccessoriesStandards: EN 598 | Company standard | EN 14 901Material: Passivated stainless steel | Polyamide joint pieces | EPDM seal | NBR rubber insert Chromated nuts

DN Pipe dimensions (external diameter) mm Clamping range Weight/unit Part no. Price/unitCasting ac pipe Steel mm kg €

80 98 98-104 88.9 85-105 0.8 90403306 69.00100 118 118-130 114.3/108 105-130 0.8 90403307 70.10125 144 145-159 139.7/133 130-155 1.3 90403308 72.40150 170 172-182 168.3/159 155-185 1.3 90403309 73.60



FITTINGS

VONROLL/DUKTUS MMI 45 double socket branch 45° – Wastewater

Version: TYTON socket joint | Smooth, stoneware pipes which are suitable for the socketStandards: EN 598 | Company standard | EN 14 901Material: Ductile cast iron | Epoxy resin coating of at least 250 µm



200 150 34.5 0106023680 473.50



FITTINGS

VONROLL/DUKTUS MMM 45 double socket branch 45° – Wastewater

Version: TYTON socket joint | Push-in socket L spigots which are suitable for stoneware pipes | incl. pot seal and boltsStandards: EN 598 | Company standard | EN 14 901Material: Ductile cast iron | Epoxy resin coating of at least 250 µm



200 150 38.0 0106023900 546.20



FITTINGS

VONROLL/DUKTUS ICI 67 smooth end branch 67° – Wastewater

Version: Spigots suitable for ductile cast iron pipesStandards: EN 598 | Company standard | EN 14 901Material: Ductile cast iron | Epoxy resin coating of at least 250 µm



200 150 30.0 0106023524 398.70



FITTINGS

VONROLL/DUKTUS SCH shaft connection piece – Wastewater

Version: TYTON socket joint | Incl. sealing ringStandards: EN 598 | DIN 28 603 | Company standard | EN 14 901Material: Ductile cast iron | Epoxy resin coating of at least 250 µm | TYTON seal NBR

DN Weight/unitkg


150 7.1 0106003250 121.20200 8.0 0106012349 135.10250 10.0 0106012357 207.40300 12.5 0106012365 271.50350 15.0 0106010676 483.50400 16.5 0106012373 483.50500 22.0 0106012381 760.80600 26.5 0106012389 961.80700 43.0 0106012397 1,790.60800 49.0 0106012405 2,271.80900 61.0 0106012413 3,851.60

1.000 71.5 0106012421 4,834.80



FITTINGS

VONROLL/DUKTUS RRF tube cleaning piece – Wastewater

Version: Flange joint | PN 10Standards: EN 598 | EN 1092-2 | Company standard | EN 14 901Material: Ductile cast iron | Epoxy resin coating of at least 250 µm

DN Weight/unitkg


80 40.0 0106027955 2,607.30100 42.0 0106024067 2,866.00125 70.0 0106026163 3,588.30150 68.0 0106024068 3,786.30200 90.0 0106024069 4,691.00250 113.0 0106024070 5,995.20300 170.0 0106024071 7,071.70350 240.0 0106024073 8,603.70400 268.0 0106024074 11,468.50500 414.0 0106024076 13,557.40



FITTINGS

VONROLL/DUKTUS MM fitting – WastewaterTYTON coupling

Version: TYTON socket joint | incl. sealing ringStandards: EN 598 | Company standard | EN 14 901Material: Ductile cast iron | Epoxy resin coating of at least 250 µm | TYTON seal NBR

DN Weight/unitkg


150 8.0 0106159968 184.10200 11.5 0106012837 228.30250 14.5 0106012845 300.60300 20.0 0106012853 487.00350 26.0 0106018796 678.00400 32.0 0106012861 827.20500 45.0 0106012869 1,147.50600 56.0 0106012877 1,460.90700 97.0 0106012885 2,324.20800 128.0 0106012893 4,371.20



FITTINGS

VONROLL/DUKTUS tube sealing lid – Wastewaterwith a bleed valve

Version: Standards: Company standard | EN 14 901Material: Ductile cast iron | Epoxy resin coating of at least 250 µm

DN Weight/unitkg


150 1.0 0106025841 128.20



SEALS

VONROLL/DUKTUS TYTON sealing ring

Standards: EN 681-1 | DIN 28 603Material: EPDM/W270 for drinking water | NBR/perbunan for wastewater

EPDM / W270 NBR/perbunan

DN Part no. Price/unit€


80 113529 3.60 108058 6.60100 113530 3.80 110550 7.00125 113531 5.30 110559 9.30150 113532 5.70 100572 10.30200 113533 8.40 100671 16.70250 113534 10.30 100571 20.70300 113535 14.10 100485 24.10350 113536 20.70 112199 36.10400 113537 24.70 100591 40.80500 113538 36.80 110932 70.20600 113539 48.10 100672 110.30700 113540 90.20 110417 183.80800 113541 117.00 112090 253.30

1000 113560 297.40 112198 509.20



SEALS

VONROLL sealing ring and slide ringfor screwed socket fittings (union)

Standards: EN 681-1 | DIN 28 603Material: EPDM/W270 for drinking water | NBR/perbunan for wastewater

EPDM/W270 NBR/PERBUNAN




40 113542 3.30 111542 2.6080 113545 5.00 108041 8.40 100532 1.90

100 113546 6.00 100965 10.70 100502 2.60125 113547 7.40 108040 12.00 100533 3.30150 113548 8.70 110633 14.70 100534 3.60200 113549 11.30 108038 20.70 100535 4.70250 113550 16.00 108037 26.00 100537 6.00300 113551 22.10 108036 36.10 100538 9.30400 113553 31.40 110639 52.10 100540 15.40

SLIDE RING



SEALS

VONROLL threaded ringfor screwed socket fittings (union)

Standards: EN 545 | EN 598 | Company standardMaterial: GGG/epoxy resin or GGG/bitumen

CASTING/EPOXY CASTING/BITUMEN



40 90411296 44.10 90412834 27.7080 90403918 46.70 90403503 41.60

100 90403505 50.40 90403504 45.40125 90403931 57.10 90403543 51.10150 90403545 59.90 90403544 56.10200 90403547 71.90 90403546 72.50250 90403699 114.70 90401152 111.00300 90403754 131.10 90403548 129.20400 90403814 237.10 90403647 204.90



SEALS

VONROLL/DUKTUS sealing ring and gland nut ringfor fittings with a gland nut socket

Standards: EN 545 | EN 598 | Company standardMaterial: EPDM for drinking water | NBR for wastewater | Steel gland nut ring/epoxy resin or steel/bitumen

EPDM NBR



500 102683 161.10 110847 183.80600 102684 197.20 107846 243.90



500 90404252 400.40 90403576 289.40600 90410816 384.60 90410829 308.90

Sealing ring

Fig. 0000

STEEL/EPOXY STEEL/BITUMENGland nut ring

Fig. 0000



SEALS

VONROLL/DUKTUS TYTON-SIT-PLUS sealing ring drinking water (BRS)and identification ring

Standards: EN 681-1 | DIN 28 603Material: EPDM

DN Pressure class BRS ≙ PFA bar


80 32 113561 22.50100 32 113562 25.00125 25 113565 27.00150 25 113566 30.00200 25 113567 57.50250 25 113568 75.00300 25 113569 100.00350 25 113570 245.00400 16 113571 255.00500 16 113572 360.00600 10 113573 465.00


80 112429 1.70100 112430 2.20125 112431 3.60150 112432 3.80200 112433 4.00250 112434 4.20300 112435 4.50350 112436 4.80400 112437 5.00500 112438 5.20600 112439 7.50

Sealing ring

White NBR

Fig. 0000

Identification ring

Please note that the TYTON-SIT-PLUS seals can only be delivered in conjunction with the associated socket fittings.



SEALS

VONROLL/DUKTUS TYTON-SIT-PLUS sealing ring wastewater (BRS)and identification ring

Standards: EN 681-1 | DIN 28 603Material: NBR

DN Pressure class BRS ≙ PFA bar


80 32 112732 29.00100 32 112733 32.00125 25 112734 35.10150 25 112735 39.00200 25 112736 75.00250 25 112737 97.00300 25 112738 128.00350 25 112739 320.00400 16 112548 332.00500 16 112740 460.00600 10 112741 600.00

Sealing ring


80 112429 1.70100 112430 2.20125 112431 3.60150 112432 3.80200 112433 4.00250 112434 4.20300 112435 4.50350 112436 4.80400 112437 5.00500 112438 5.20600 112439 7.50

White NBR

Fig. 0000

Identification ring

Please note that the TYTON-SIT-PLUS seals can only be delivered in conjunction with the associated socket fittings.



SLEEVE PROTECTION

Combined protective sleeves for pipes with external CMC or PUR

Version: Combined protective sleeves for BLS/HYDROTIGHT/TYTON pipesMaterial: EPDM

DN Weight / mkg


80 0,2 700903025 9.80

100 0,2 700903026 10.00

125 0,3 700903027 10.70

150 0,3 700903028 11.90

200 0,4 700903029 14.20

250 0,5 700903030 18.00

300 0,7 700903031 20.00

400 0,8 700903032 35.70

500 0,9 700903033 51.50

600 1,9 700903034 53.50

700 2,5 700903322 115.00

Shrink-on collars (thermally) closed for pipes with external CMC/PUR

Version: Shrink-on collars for shrinking BLS/HYDROTIGHT/TYTON pipesMaterial: Polyethylene

DN Connection Weight / mkg


80 TYT/BLS 0.30 700900119 15.00

100 TYT/BLS 0.35 700900120 16.00

125 TYT 0.45 700900121 18.00

125 BLS 0.55 700900122 18.00

150 TYT/BLS 0.55 700900122 18.00

200 TYT/BLS 0.65 700900123 22.50

250 TYT/BLS 0.75 700900124 30.00

300 TYT/BLS 0.85 700900125 35.00

350 TYT 1.20 700900126 51.00

400 TYT/BLS 1.35 700900127 57.00

500 TYT/BLS 1.55 700900128 66.00

2004

/ X

XXXX

XX /

EN

/ Y

000

/ ga

l

pipes and fittings › files › content › downloads › ... · pipes and fittings general...

Documents