ELECTRICAL HAZARD!

TURN POWER OFF BEFORE WORK!

PF10222

Surface Mount Box

IMPORTANT: Please read carefully the followinginstructions before beginning.

FBS FLOOR BOX SYSTEMS

25060 Hancock Ave

STE 103-125

Murrieta, CA 92562

1-800-216-8307 - Instal lat ion Guide -

Remove the screws located on the front side of the box to separate the

base from the body . Keep the screws in a safe place for later use.

1

B: Feeding the box through a flush mounted outlet box

A: Feeding the box through a conduit

C: Feeding the box from a wood/raised floor opening

Attach a 1/2” or 3/4” conduit to

the KO bottom plate (Part #

FBS111) (Sold Separate).

NOTE: The FBS111 plate has

one concentric knockout for

1/2” and 3/4” conduits.

Align the base of the box with

the KO plate. Using the appro-

priate screws, mount and se-

cure them to the selected area

NOTE: The base and the KO

bottom plate (#FBS111) have

screw holes at all four corners.

Continue to step 3.

Attach the conduit to a single

gang outlet box. Install the SG

outlet box (not supplied) flush

with the floor.

For raised/wood floor applica-

tions, use an “Old Work” type

single gang outlet box

(not supplied) .

Align screw holes on the base

of the PF10222 with the screw

holes on the outlet box and se-

cure them w/ 6/32” screws (not

supplied)

NOTE: The base has screw

holes at the four corners and

two screw holes that match the

hole pattern of the outlet box.

Continue to step 3.

Drill a hole on the wood/raised

floor and pull the cables out

thru the opening

NOTE: Method recommended

for A/V, VGA connectors and

connectors larger than 3/4”.

Secure the base of the

PF10222 Surface Mounted

Floor Box to the floor.

The base has screw holes at all

four corners.

Continue to step 3.

Installation process varies depending on themethod selected to feed the box.

See the feeding options below (step 2, A, B, C)and select the appropriate method for yourapplication.

Questions? 1.800.216.8307 www.FloorBoxSystems.com

Warning:

To be installed and/or used in accor-

dance with appropriate electrical

codes and regulations.

Warning:

To avoid fire, electrical shock and/or

electrocution turn power OFF at the

circuit breaker before wiring.

Caution:

Wire devices in accordance with the

NEC. If you are not sure about exist-

ing conductor wires, color coding, po-

larity and circuit feed contact a

licensed electrician.

DISCLAIMER - (Worldwide)

FBS FLOOR BOX SYSTEMS MAKE

NO WARRANTIES OR REPRESENTA-

TIONS, WHATSOEVER, EXPRESS OR

IMPLIED, AS TO THE MER-

CHANTABILITY, FITNESS OR SUIT-

ABILITY OF THIS PRODUCT.

Installer/Buyer of this product must ver-

ify the suitability and approval of this

product for the specific use with the

local codes and/or authorities having ju-

risdiction in the area where the product

will be installed.

PF10222

Surface Mount Box

FBS FLOOR BOX SYSTEMS

25060 Hancock Ave

STE 103-125

Murrieta, CA 92562

1-800-216-8307 - Instal lat ion Guide -

Fasten the screws removed on the

step 1 to secure the body (box) to

the base.

3

Pull the cables at least 7” through

the box opening to facilitate the

wiring job.

4

Wire devices in accordance with the

NEC. Align the modules and push

them gently into the opening until

they snap in place.

5

Gently press the small screw caps

on one side and remove it. Remove

the screws to separate the

yoke/faceplates from the body.

1

Separate the yoke. Disconect wires

from the device.

2

Insert a flat head screwdriver (prefer-

ably 5 mm width) into the back side of

the yoke and turn slightly 10° to 30°

until module is released. If needed,

repeat on both ends of the module.

3

Module removal instructions

Device configuration may vary.

6

Questions? 1.800.216.8307 www.FloorBoxSystems.com

2 3/4” (70 mm)

1/4”

(12 mm)

5 1/2”

(140 mm)

2 7

/8”

(73

mm

)

2”

(50

mm

)

CAUTION: When printing copies of this template please be sure template is scaled correctly and is the correct size once it is

printed.

19/32”

(15mm)

PF10222

Surface Mount Box

FBS FLOOR BOX SYSTEMS

25060 Hancock Ave

STE 103-125

Murrieta, CA 92562

1-800-216-8307 -Template -

Questions? 1.800.216.8307 www.FloorBoxSystems.com

3 5/16” (83.33 mm )