pdh nms user manual
TRANSCRIPT
-
8/2/2019 PDH NMS User Manual
1/26
COMPACT PDH
NETWORK MANAGEMENT
User Manual
-
8/2/2019 PDH NMS User Manual
2/26
NMSUser Manual Page 2 of 26
1. Summary
NMS management system is used for managing PDH devices, it has network
management functions of enquiry alarm, performance and data configuration.
System request
Microsoft Windows TM NT/2000 series operating system
CPU of above Pentium TM II350
EMS memory of above 256MB
Display resolution of 1024768
Harddisk of above 10Gb spare capacity.
Software installation
NMS software installation is very simple, user only needs to find installation file
setup.exeand then install according to the clews.
2. Communication mode of network management
NMS network management system can manage multi units of PDH in multi-network.
2.1 Short-range management
PDH devices only offer one kind of network management port: serial port. If there is
only ETH in external environment, you can use virtual serial card. PDH can support 16
serial ports at most.
Serial Network Management method
-
8/2/2019 PDH NMS User Manual
3/26
NMSUser Manual Page 3 of 26
Serial virtual ETH Network Management method
2.2 Remote management
Remote management means that NMS and device is not at the same place. NMS
manages PDH device through ETHcommon telephone line or DDN, such as followed
pictures:
-
8/2/2019 PDH NMS User Manual
4/26
NMSUser Manual Page 4 of 26
Serial virtual ETH remote method
Serial remote method (centralized)
PDH (veneer) devices can use virtual serial card to extend serial port to device
through ETH
-
8/2/2019 PDH NMS User Manual
5/26
NMSUser Manual Page 5 of 26
3. Basic operation
3.1 Login in the system
In default mode:Username is nullPassword is null
3.1.1 Main interface
-
8/2/2019 PDH NMS User Manual
6/26
NMSUser Manual Page 6 of 26
3.1.2 Modify the Username
-
8/2/2019 PDH NMS User Manual
7/26
NMSUser Manual Page 7 of 26
Enter the old Username, old Password and New Username
When follow picture is show, the Username modified successful.
3.1.3 Change the Password
Enter old Password, new Password and confirm Password
When follow picture is show, the Password change successful.
Use the new Username and Password to login the system.
-
8/2/2019 PDH NMS User Manual
8/26
NMSUser Manual Page 8 of 26
3.2 Enter the main interface
3.3 Add subnet
When PDHis running for the first time, the navigating menu is blank. Click right key
of mouse, there will be pull-down menu of adding subnet, click Add Subnet, there will
be dialog box of adding subnet. If using keyboard, please press Add directly, there will
be followed dialog box. Note: you can add multi Subnet at the same time in NMS
-
8/2/2019 PDH NMS User Manual
9/26
NMSUser Manual Page 9 of 26
Input subnet name directly in the dialog box, after clicking Add Subnet or press
ENTER, subnet will be added, and there will be dialog box of successful operation.
Use the Add Descriptionto describe the Subnet
Enter the description
-
8/2/2019 PDH NMS User Manual
10/26
NMSUser Manual Page 10 of 26
Show the Network Property
-
8/2/2019 PDH NMS User Manual
11/26
NMSUser Manual Page 11 of 26
3.4 Add network element
Select subnet which has been added, click right key of mouse, there will be pull-
down menu, and click the left key Add ne, there will be the interface of adding network
element, can add multiNe in one Subnet, that is,in one Subnet can add multi unitsof devices.
Then choose the device type and set the Ne Name in this interface, in this interface
will introduce the each device. After click the Add, the device view in NMS will be show.
-
8/2/2019 PDH NMS User Manual
12/26
NMSUser Manual Page 12 of 26
3.5 Modify the Ne Name and Add Description
Modify the Ne name
Enter the new Ne Name
Then the Ne Name in NMS system will show
-
8/2/2019 PDH NMS User Manual
13/26
NMSUser Manual Page 13 of 26
Add the description of Ne
Enter the description in the follow interface
-
8/2/2019 PDH NMS User Manual
14/26
NMSUser Manual Page 14 of 26
Show the Ne Property
The view will show the information of Ne
-
8/2/2019 PDH NMS User Manual
15/26
NMSUser Manual Page 15 of 26
3.6 Set the Link property of network element
Select network element which has been added, click Connect button in the view. ,
there will be pull-down menu, and choose which serials port is available in PC which
connect to the PDH through the console cable.
Then the system will show
-
8/2/2019 PDH NMS User Manual
16/26
NMSUser Manual Page 16 of 26
When the PDH has connected the NMS system, the NMS system will show the state of
PDH.
The red LED in the panel means alarm.
The green LED in the panel means the state normal.
If there is any alarm in current PDH the Ne will show red
-
8/2/2019 PDH NMS User Manual
17/26
NMSUser Manual Page 17 of 26
3.7 Network element-management
3.7 .1 Button in the NMS system
Save: save current settings into system, can use for setting of other devices, but need
Download to device, then setting can become effective.
Default: resume the default value configured by interface, at this time data hasnt been
sent down to device, through clicking Apply button, the default data can be sent down to
device.
Download: after data of network manager interface is configured, the configuring data
can be sent down to device through clicking Download button. After the device receives
the newest configuring data, they are stored to FLASH memorizer, and the working
mode of device is changed according to the newest configuring data.
Upload: Upload the newest network manager data which is stored in FLASH memorizer,
and show them through network manager interface.
Exit: exit the network management system.
3.7.2 Alarm information in the NMS system
Click the Local Alarm button can check the local alarm.
-
8/2/2019 PDH NMS User Manual
18/26
NMSUser Manual Page 18 of 26
Click the Remote Alarm button can check the remote alarm.
3.7.3 Configure the device
Click the Config button, can configure the device, E1 and Ethernet port in the device.
In this interface, can set the Port Separation, Port-base VLAN, 802.1Q Tag VLAN,
Special Tagging.
-
8/2/2019 PDH NMS User Manual
19/26
NMSUser Manual Page 19 of 26
3.7.3 .1 Special Tagging
Special Tagging is a private protocol. It will add a Tagging on the ETH packet which hadset the 802.1Q VLAN Tag. It can use add the Tag ID in the network. It can separate the4ETH port in the PDH base on Tag, but never effect the VLAN ID in the switch which
connect to the ETH port of PDH.
Like follow:
In the Special Tagging mode, the LAN1, LAN2, LAN3, LAN4 cant communication eachother, the each LAN, can set VLAN ID of 1-4095.In the NMS system, each PDH can be set to be 4 special Tagging at most, each ETHport is set to be 1 special Tagging.
-
8/2/2019 PDH NMS User Manual
20/26
NMSUser Manual Page 20 of 26
3.7.3 .2 802.1Q tag VLAN
For example
As above picture,
User A1 only can communicate with User B1;
User A2 only can communicate with User B2;
User A3 only can communicate with User B3;
User A4 only can communicate with User B4;
Add 5 records in VLAN table,
Set LAN 1 and WAN to belong to VLAN 1;
Set LAN 2 and WAN to belong to VLAN 2;
Set LAN 3 and WAN to belong to VLAN3;
Set LAN 4 and WAN to belong to VLAN 4;
Set LAN 1LAN 2LAN 3LAN 4 and WAN to belong to VLAN 5;
-
8/2/2019 PDH NMS User Manual
21/26
NMSUser Manual Page 21 of 26
Set PVID of LAN 1 to be 1;
Set PVID of LAN 2 to be 2;
Set PVID of LAN 3 to be 3;
Set PVID of LAN 4 to be 4;Set PVID of WAN to be 5;
-
8/2/2019 PDH NMS User Manual
22/26
NMSUser Manual Page 22 of 26
Port Separate is set to be DisableVLAN Mode is set to be IEEE 802.1q Tag VLAN.
At the same time need to set 802.1q Tagof WAN port to be VLAN TagInsertion,
-
8/2/2019 PDH NMS User Manual
23/26
NMSUser Manual Page 23 of 26
Then click the Download
Click the OK, the configuration is downloaded to the device.
-
8/2/2019 PDH NMS User Manual
24/26
NMSUser Manual Page 24 of 26
3.7. 4 Set the ETH Port
This interface is used for configuring attribute of each ETH port, including LAN port 1,
2, 3, 4 and one WAN port. LAN port shows 4 ETH ports offered by device, WAN port is
inner port of device, which connects remote device through optical port. Attribute
configuration of each ETH port includes 802.1Q tag Insertion and Removal, 802.3 X
Pause Enable and Disable, Port Forwarding Enable and Disable, Broadcast Storm
Protection Enable and Disable, Port Rate Limitation based on 32kbps (speed range is
0~100M), Speed and Duplex configuration of each ETH port.
802.1q Tag: Insert shows to insert Tag, when the data packet which is output from this
port has been with Tag, dont make any changes; if without Tag, insert VLAN ID which is
default in input port in the data packet.
Remove shows to remove Tag, when the data packet which is output from this
port has been with Tag, remove this Tag; if without Tag, dont make any changes.
802.3X: Enable shows to enable PAUSE of ETH port, Disable shows to disable
PAUSE of ETH port.
Port ForwardingEnable shows to enable Port Forwarding of ETH port, Disable
shows to disable Port Forwarding of ETH port.
Broadcast Storm ProtectionEnable shows to enable restrain function of ETH
Broadcast Storm, this port only allows 1% of ETH Broadcast packet to pass. Disable
shows to disable restrain function of ETH Broadcast Storm, this port forwards all ETH
Broadcast packet.
Rate Limitation: take 32kbps as step-size to adjust port rate, value rang is 0~3200.
-
8/2/2019 PDH NMS User Manual
25/26
NMSUser Manual Page 25 of 26
Speed and Duplexcan be separately set to be AUTO, forced 100M full-duplex, forced
100M half-duplex, force 10M full-duplex, force 10M half-duplex.
3.7. 5 Set the E1 Channel
In E1 Channel view, can check the estate of each E1 of device, also can set loop estateof each E1 channel, can set each E1 channel as No Loop, Local Loop or RemoteLoop, which is easy to test and manage estate of each E1 channel.
-
8/2/2019 PDH NMS User Manual
26/26
NMSUser Manual Page 26 of 26
3.8 Status of the device
This view mainly shows the working estate of current device.
3.9 Disconnect the device.
Use of buttonDisconnectis to disconnect RS232 connection of NMS system and device.