1

SBI INFRA MANAGEMENT SOLUTIONS PVT. LTD.

(A Wholly Owned Subsidiary of SBI)

CIRCLE OFFICE

SBI Local Head Office, 4th Floor, III/1 Pandit Jawaharlal Nehru Marg, Bhubaneswar- 751001

Part – II

(Price Bid)

ELECTRICAL AND ALLIED WORK OF SBI DHENKANAL MAIN BRANCH

Tender reference No: SBIIMS/BHU/ELECT./2018-19/49

(Not to be filled by the Bidder, Rate to be quoted Online)

Note: Bank’s (SBI LHO, Bhubaneswar) Empanelled Electrical Contractor under LT category- A,

B C, & D are only eligible to participate in this tender. Vendor/Contractor should possess valid digital signature for this e-tender.

TENDE R SUBMITTED BY: NAME : ADDRES S : _________________________________ GSTIN NO : DATE :

A R C H I T E C T S :

M/s Techno Arch,

Bhubaneswar.

2

ELECTRICAL BOQ FOR STATE BANK OF INDIA, DHEKANAL MAIN BRANCH . SL.NO. DESCRIPTION OF ITEMS UNIT QUANTITY RATE

(Rs.) AMOUNT

(Rs.)

A ELECTRICAL WIRING WORK

1.0 Concealed / ressessed / surface light point / fan point / call bell point etc. wiring using 1100V FRLS grade 3R (P+N+E) x 1.5 Sq.mm FRLS multi stranded copper conductor PVC insulated wires (with proper R,Y,B color code) pulled through rigid FR/FRLS PVC conduits of 20mm Dia 1.5 mm thick laid concealed over false ceiling or in wall chases or on the ceiling in case of an open ceiling, with modular type switch plate, switches, GI concealed back box, etc. of legrand mylinc or equivalent make. S.I.T.C.( Supply Installation Testing And Commissioning) as directed by the Engineer-in-charge. (Each circuit shall not feed more than 8 points OR 800 watts as per following configuration.)

NOTE:- 1. Only FRLS wire shall be used; 2. The wires from ceiling junction to light points / light fixture shall be drawn in flexible PVC conduit with adptor & cover for junction box & crimp type lugs at both the ends alongwith necessary hardware & accessories, etc. as required; 4. Looping of Neutral / Earth wire between two seperate Primary / Full Points is strictly not allowed; 5. Looping of Neutral / Earth wire between two seperate circuits on similar or other phase is strictly not allowed; 6. Ferulling / numbering / taggning to wires with circuit number & db name for all lighting & raw / ups power shall be strictly followed at both DB & switch board / switch socket boards ends.

1.1 Primary light points including the cost of clip in type 6A Modular switch of legrand mylinc or equivalent make. S.I.T.C. as directed by the Engineer-in-charge.( 1 light/fan controlled by one switch)

Nos. 175.00

1.2 Subsequent point ( Looped From Primary) Nos 75.00

1.3 Independent point using one 6 Amp Modular Switch and one 6 Amp, 2/3 pin Modular scoket mounted on a sutable size Box including wiring using 1100V FRLS grade 3R (P+N+E) x 1.5 Sq.mm FRLS multi stranded copper conductor PVC insulated wires for wall fans.

Nos 58.00

3

1.4 6 Amp 2/3 pin Modular scoke with 6A Modular switch. ( on common switch Board.)

Nos. 10.00

1.5 Primary light points including the cost of clip in type 6A Modular switch of legrand mylinc or equivalent make & model as approved by project in charge. ( I light controlled by one switch UPS point )

Nos. 8.00

2.0 Concealed power point using 16 Amp 3 Pin plug socket with 16 Amp Modular switch of legrand mylinc or equivalent make mounted on separate board using suitable size galvanized iron junction & switch boxes & clip in type modular type switch plate,etc. Supply taken from R.D.B./ Nearest L.D.B. The point should not taken from any switch Board. S.I.T.C. as directed by the Engineer-in-charge.

Nos 12.00

3.0 Concealed raw power point using 2 nos of 6 Amp 2/3 Pin Modular plug socket with 16 Amp Modular switch of legrand mylinc or equivalent make on separate board using galvanized iron junction & switch boxes & clip in type modular type switch plate, GI/PVC concealed back box, etc. supply taken from R.D.B./ Nearest L.D.B.The point should not taken from any switch Board. S.I.T.C. as directed by the Engineer-in-charge

Nos 20.00

4.0 Concealed raw power point using 6 Amp, 2/3 Pin Modular plug socket with 6 Amp Modular switch of legrand mylinc or equivalent make on separate board using galvanized iron junction & switch boxes & clip in type modular type switch plate, switches, GI/PVC concealed back box, etc. Supply taken from Nearest L.D.B. Maximun 3 Points per Circuit for counter & Table

Nos 39.00

5.0 Supply,installation and testing of timer with contactor ( L&T / Legrand ) make controlling the glowsign board with all accessories complete enclosed in Powder coated metal box as required as per direction of Engineer in charge. The system will be apart of the panel board.

Nos. 2.00

6.0 Supply of all required materials and wiring to circuits/ submains with following number and sizes of PVC insulated 1100 volt grade multi standard FRLS copper wire run inside rigid FR/FRLS PVC conduits of 20mm Dia 1.5 mm thick of ISI mark as required and copper wire as earth continuity conductor and complete in all respect including making good to all damages caused and as per the direction of Consultant and Engineer-in-charge.

4

6.1 Concealed wiring with ( 2Rx2.5sqmm +1Rx1.5sqmm) copper wire ( LDB/RDB to Common Switch board and Raw Points for item no (A) 2.0,3.0,4.0)

Mts 545.00

6.2 Concealed wiring with ( 2Rx6.0 sqmm +1Rx4.0 sqmm copper wire ( PANEL to L.D.B./R.D.B.)

Mts 200.00

6.3 Concealed wiring with ( 4Rx10sqmm) + 2Rx6sqmm) copper wire ( PANEL to U.P.S. input )

Mts 10.00

7.0 S & I of 1100V grade Aluminium armoured cable having sector / circular shaped aluminium conductor PVC insulated cores, laid up, PVC tape wrapped inner sheathed, GI strip / wire armoured and overall extruded PVC sheathed confirming to IS: 1554, laid on wall or ceiling using GI clamps and spacers as per route shown at site and further as directed by Bank / Architect in the following sizes.

7.1 Surface/Concealed wiring with (95sq.mm)3 1/2 core armored almunium cable with 2 runs of 12 SWG GI bare wire ( Main Panel input from Meter Box)

Mts 30.00

7.2 Surface/Concealed wiring with (35sqmm)3 1/2 core armored almunium cable with 2 runs of 12 SWG GI bare wire (From main Panel to master AC Contoller/ master AC Contoller to Main Panel / Generator to Main panel )

Mts 60.00

7.3 Surface/Concealed wiring with (16 sqmm)3 1/2 core armored almunium cable with 2 runs of 12 SWG GI bare wire ( M.L.D.B input from main panel)

Mts 25.00

8.0 GLANDING & TERMINATION :- Supply & In-stallation of end termination of above mentioned cables including compressed type brass glands, crimping type copper lugs, insulation tape etc. as 'required complete with earthing of glands in fol-lowing sizes :-

8.1 (95sq.mm)3 1/2 core armored almunium cable Nos 2.00

8.2 (35sqmm)3 1/2 core armored almunium cable Nos 6.00

8.3 (16 sqmm)3 1/2 core armored almunium cable Nos 2.00

TOTAL FOR ELECTRICAL WIRING WORK Rs.

B COMPUTER WIRING WORK

5

1.0 Supplt and fixing of concealed UPS power points using 1 nos. of 16 Amp, 3 Pin Modular switches to be provided on table top + 4 nos. 6 Amp Modular socket below table top of legrand mylinc or equivalent make taken from Nearest C.D.B with sutable size galvanized iron/PVC junction & switch boxes & clip in type modular type switch plate, GI/PVC concealed back box, etc. Maximun 3 Points per Circuit for counter & Table. S.I.T.C. as directed by the Engineer-in-charge.

SET 45.00

2.0 Supplt and fixing of concealed UPS power points using clip in modular type 5 No. of 6/16 amp socket points controlled by 2 No of 16 amp modular switch with indicator of legrand mylinc or equivalent make taken from Nearest C.D.B with galvanized iron junction & switch boxes & clip in type modular type switch plate, switches, GI concealed black box, etc. . The point should not from any switch Board S.I.T.C. as directed by the Engineer-in-charge.

SET 2.00

3.0 Supply of all required materials and wiring to circuits/ submains with following number and sizes of PVC insulated1100V FRLS grade 3R (P+N+E) x folling size FRLS multi stranded copper conductor PVC insulated wires (with proper R,Y,B color code) pulled through rigid FR/FRLS PVC conduits of 20mm Dia 1.5 mm thick ISI mark laid concealed over false ceiling or in wall chases or on the ceiling in case of an open ceiling including of as required and multy stranded copper wire of folling size as earth continuity conductor and complete in all respect including making good to all damages caused and as per the direction of Consultant and Engineer-in-charge.

3.1 Concealed wiring with ( 2Rx2.5sqmm +1Rx1.5sqmm) copper wire ( C.D.B. to Computer Points )

Mts 750.00

3.2 Concealed wiring with ( 2Rx4.0 sqmm +1Rx2.5sqmm) copper wire ( U.P.S. OUTPUT to C.D.B. )

Mts 250.00

TOTAL FOR COMPUTER WIRING WORK Rs.

C A.C. WIRING WORK

6

1.0 Supply & Installation of all required materials and wiring to Split AC 16 Amp 3 Pin Modulat socket mouted on suitable size concealed GI Box near to the AC controlled by 25 Amp DP isolator Enclosed in Powder coated DP Encloser of Legrand Ekinox3 model or Equivalent make taken from Nearest A.C..D.B/ M.L.D.B. with galvanized iron junction & switch boxes & clip in type modular type switch plate, switches, GI concealed back box, etc. of legrand mylinc or equivalent make.The point should not taken from any switch Board S.I.T.C. as directed by the Engineer-in-charge.

Nos. 2.00

2.0 Supply of all required materials and wiring to 2 nos of Split AC in System Room with 2 nos 16 Amp Modualar socket of legrand mylinc or equivalent make mouted on suitable size GI concealed Box controlled by 25 Amp Digital timer operated Alternatevly supplied by a 25 Amp RCBO Sensityvity 30mA Enclosed in 6 way SPN DB of Legrand or Equivalent make taken from Nearest M.L.D.B. with galvanized iron junction & switch boxes & clip in type modular type switch plate, switches, GI concealed back box, etc. .The point should not taken from any switch Board. S.I.T.C. as directed by the Engineer-in-charge.

Nos. 1.00

3.0 Supply and installation of Concelaed 20A/25A, 230 V DP Isolator mounted in a prefabricated powder coated DP metal enclosure (legrand make Ekinox3 model or equivalent make ) concealed and complete to the satisfaction of Bank for 2 TR Cassatte AC.S.I.T.C. as directed by the Engineer-in-charge.

Nos. 5.00

4.0 Supply and installation of Concelaed 20A/25A, 415 V FP Isolator mounted in a prefabricated powder coated FP metal enclosure (legrand make Ekinox3 model or equivalent make ) concealed and complete to the satisfaction of Bank for 3 TR Cassatte AC.S.I.T.C. as directed by the Engineer-in-charge

Nos 8.00

7

5.0 Supply and Installation of all required materials and wiring to circuits/ submains with following number and sizes of PVC insulated 1100 volt grade standard FRLS copper wire run through rigid FR/FRLS PVC conduits of 20mm Dia 1.5 mm thick ISI mark as required and copper wire as earth continuity conductor and complete in all respect including making good to all damages caused and as per the direction of Consultant and Engineer-in-charge.

5.1 Concealed wiring with 2 X 4sq. mm + 1 X 2.5sqmm copper wire ( From ACDB/M.L.D.B. to 2.0 Ton Cassette /Split A.C. points through DP Isolator. )

Mts 160.00

5.2 Concealed/Surface wiring with 4 core 6 Sq. mm Copper Flexible FRLS wire with 2R X 2.5 copper FRLS wire. ( From ACDB to Cassette A.C through FP Isolator . )

Mts. 180.00

6.0 S & I of 1100V grade armoured cable having sector / circular shaped aluminium conductor PVC insulated cores, laid up, PVC tape wrapped inner sheathed, GI strip / wire armoured and overall extruded PVC sheathed confirming to IS: 1554, laid on wall or ceiling using GI clamps and spacers as per route shown at site and further as directed by Bank / Architect in the following sizes.

6.1 Concealed/Surface wiring with 4 core 16 sq. mm Al. cable with 2R X 12 SWG GI wire . ( From Main Panel to ACDB)

Mts 90.00

TOTAL FOR AC WIRING WORK Rs.

D PANEL BOARD & DISTRIBUTION BOARDS.

1.0 Main Panel Board Set 1.00

8

Supply, delivery, installation , testing , commissioning , of indoor wall mounted , type distribution boards made out of 2 mm thk. CR sheet metal painted with 2 coats of enamel paint compartment arrangement for each equipment & bus bar chamber on the top of the panel running horizontal through , vermin proof having provision cable by conduit entry , earthling stud as per specification mentioned below duly factory wired confirming to the relevant ISS & as per special condition of contract , making good the damages M.S. Cubical type Panel board should have hinged door at the front. The panel shall be provided with all accessories & following arrangements complete in all respect & direction of EIC (before fabrication of panel board drawing is to be approved by Engineer-in-charge). The Contractor should Submit The Testing Cartificate to the Client after Installation.

Incoming :-

1No 250A- 40KA - 4POLE -MCCB.

1 set of 300A TPN copper bus bar (25 X6 mm)

1No 160A- 25KA - 4POLE -MCCB.

1 set of 200A TPN copper bus bar(25 X4 mm)

160A, 4-POLE Change over

1 set of 200 A TPN copper bus bar(25 X4 mm)

Out going :-

1No 30KA - 63A TPN SPD

2No 63A- - 4POLE -10 kA - MCB.For A.C.DB

1No 63A- - DP -10 kA -MCB. For A.C.DB

2No 63A- - 4POLE -10 kA -MCB. Spare

1No 63A- - DP -10 kA -MCB. Spare

1 Nos 63A, 4P -10 kA -MCB, for U.P.S.

1 Nos 63A, 4P-10 kA - MCB, Spare

1 Nos 125 A 4POLE -18 kA - MCCB for M.L.D.B.

3 Nos 32 A DP-10 kA - MCB Spare

All MCB must be class C Type

1No. Digital Volt meter with Volt meter selector switch & Control fuse.

1No. Digital Ammeter with Ammeter selector switch & CT.

Cable tray.

9

Termination bar for each out put

6 Nos Phase indicator L.E.D. lamps

2.0 Supplying & Fixing 250 Amp, 415 V Wireable IC Cutout - 3nos in MS enclouser withj lock & key arrangements.

Set 1.00

3.0 Supply and installation of SPN, Double Door, Metal type, (hager IP43, legrand make Ekinox3 model or equivalent make as approved by SBIIMS), surface / flush mounted on wall, interconnected wiring complete with earthing lugs, including DB wiring, termination of circuits with ping type copper lugs, blank plates, etc. housing following switchgears :

3.1 L.D.B (Light Distribution Board) Set 4.00

12 way SPN DB

Incoming :- 1 No. 32A DP MCB

Outgoing :- 10 No. 6-10 A SP MCB

All MCB must be class C Type

3.2 R.D.B (Raw power Distribution Board) SET 1.00

12 way SPN DB

Incoming :- 1 No. 32A DP-10 kA - MCB

Outgoing :- 10 No. 6-10 A SP -10 kA -MCB

All MCB must be class C Type

3.3 C.D.B (Computer Distribution Board) SET 3.00

12 way SPN DB

Incoming :- 1 No. 32A DP-10 kA - MCB

Outgoing :- 10 No. 6-10 A SP-10 kA - MCB

All MCB must be class C Type

3.4 C.D.B (Computer Distribution Board) SET 4.00

8 way SPN DB

Incoming :- 1 No. 32A DP-10 kA - MCB

Out going :- 6 No. 6-10 A SP -10 kA -MCB

All MCB must be class C Type

3.5 U.P.S Incoming DB SET 1.00

8 way SPN DB

63 Amp 4P-10 kA - MCB – 2 nos (1main & 1 spare).

All MCB must be class C Type

3.6 U.P.S Outgoing DB SET 1.00

12 way SPN DB

Incoming :-1 No. 63A DP-10 kA - MCB

Out going :-4 No. 32 A SP-10 kA - MCB

6 No. 25 A SP-10 kA - MCB

10

All MCB must be class D Type

3.7 A.C.D.B. (AC Distribution Board) SET 1.00

12 way SPN DB

Incoming :-1 No. 63A DP-10 kA - MCB

Out going :-5 No. 5 A DP-10 kA - MCB

All MCB must be class C Type

3.8 M.A.C.D.B. (Main AC Distribution Board) SET 1.00

4 way SPN DB

1 No. 160A -415V-4P Isolator.

4.0 Supply and installation of VTPN, Double Door, Metal type (hager IP43, legrand make Ekinox3 model or equivalent make as approved by SBIIMS), surface / flush mounted on wall, interconnected wiring complete with earthing lugs, including DB wiring, termination of circuits with ping type copper lugs, blank plates, etc. housing following switchgears :

4.1 A.C.D.B. ( AC Distribution Board) Set 2.00

6 way VTPN DB

Incoming :- 1 No. 63A 4P MCB, 63A -415V-4P Isolator.

Out going :- 5 No. 20A TP -10 kA - MCB

3 No. 25A SP -10 kA - MCB

All MCB must be class C Type

4.2 M.L.D.B. (Main Light Distribution Board) Set 1.00

4 way VTPN DB

Incoming :-1 No. 125A -415V-4P Isolator.

Out going :- 12 No. 32A SP -10 kA - MCB

All MCB must be class C Type

TOTAL FOR PANEL BOARD & DISTRIBUTION BOARDS. Rs.

E FITTINGS OF FIXTURES

(NOTE : ANY OF FIXTURES AND FITINGS SHALL BE RE-CONFIRMED WITH THE ARCHITECTS / CONSULANTS BEFOTE ORDERING THEM.

11

Supply , Installation, testing and commissioning of lighting fixtures with lamps and LED driver as per the details below including necessary hardware such as clamps, nuts, bolts, nails, screws and suspension rods as required for fixing the fixtures in position as directed by architect / consultant / client including supply and fixing flexible wires from holder to fixtures hardwares etc. Note :- All Light Fixtures, Fans, Exhaust Fans & other fittings samples shall be approved by the Client / Architect / Consultant before placing order to the Light Fixture Vendor / Supplier makes are specified. Client / Architect / Consultant reserves right to approve / select final Light Fitxtures from any make as required.

1.0 Supply,installation and testing of recess LED lights fittings ( 31 - 34 W) of squre type ( 2'-0"x2'-0") with all accessories complete of Philips RC380B -LED36S-6500-G4-L60-W60 Equivalent Make as required as per direction of Engineer in charge.

Nos. 71.00

2.0 Supply,installation and testing of recess LED lights fittings ( 14-18W) of squre type with all accessories complete Crompton LSDN-18-CDL/TL/WW Equivalent Make as required as per direction of Engineer in charge.

Nos. 6.00

3.0 Supply,installation and testing of recess LED lights fittings ( 6W) of spot type all accessories complete of Philips DN191B LED6S-6500 PSU WH S11 or Equivalent Make as required as per direction of Engineer in charge.

Nos. 63.00

4.0 Supply,installation and testing of recess LED lights fittings (10W) of spot type with all accessories complete of Philips DN092B LED10S-6500 PSU WH Equivalent Make as required as per direction of Engineer in charge.

Nos. 6.00

5.0 Supply,installation and testing of surface mounted LED lights fittings (10W) of ( Round & Square Type ) with all accessories complete of Crompton LCDSPLN-R-12-CDL / LCDSPLN-S-12-CDL Equivalent Make as required as per direction of Engineer in charge.

Nos. 39.00

6.0 Providing and fitting of 450 mm sweep High Flo Wall fan of Orient/ Crompton Equivalent Make as required as per direction of Engineer in charge.

Nos. 54.00

12

7.0 Providing and fitting of 400 mm sweep cabin fan of Orient/ Crompton Equivalent Make as required as per direction of Engineer in charge.

Nos. 4.00

8.0 Providing and fitting of 12" sweep heavy duty Exhust fan of Orient/ Crompton Equivalent Make as required as per direction of Engineer in charge.

Nos. 2.00

9.0 Providing and fitting of 9" sweep heavy duty Exhust of Orient/ Crompton Equivalent Make as required as per direction of Engineer in charge.

Nos. 5.00

10.0 Providing and fitting of 1200 mm sweep celing fan of Orient/ Crompton High Speed Equivalent Make as required as per direction of Engineer in charge.

Nos. 10.00

11.0 Providing and fitting of modular fan step Type regulator of approved make .

Nos. 10.00

12.0 Supply & fixing of fan-hook,by cutting roof slab and welding 10 mm dia.Fan hook with main re-Inforcemerit of roof slab complete in all respect

Nos. 10.00

13.0 Refitting of 1200 mm sweep celing fan of as required as per direction of Engineer in charge. Complete the job in all respect i.e painting clening, removing the deamaged material out side the premises as per instruction, including all labour.

Nos. 7.00

14.0 Supplying , fixing of 1x 20W LED Batten lights fittings with aall accessories complete of Philips BN021C LED20S PSU CDL/NW GR Equivalent Make as required as per direction of Engineer in charge.

Nos. 39.00

15.0 Providing ,Installation and testing of twin Batten LED lights fittings (2x18W) of Philips MAS LEDtube 1200mm 18W865 T8 I Equivalent Make with all accessories ( incluiding Down rod & Mounting rail of Philips TMC 501 P 2xT-LED 22W P3242 Equivalent Make complete as required as per direction of Engineer in charge.

Nos. 6.00

16.0 Providing and fitting of call bell Remote Controlled with Battery of approved make .

Nos. 4.00

TOTAL FOR FITTINGS OF FIXTURES Rs.

F EARTHING

13

1.0 Providing and fixing Earthing with G.I. earth plate 600 mm X 600 mm X 6.36 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with alternative layer of 150mm thick charcoal/ coke and salt as required. For SPD/ Panel. All earth pits installation & testing shall be as per IS 3043 with latest amendments.

Nos. 3.00

2.0 Providing and fixing of Earthing with copper earth plate 600 mm X 600 mm X 3.18 mm thick including accessories, and providing masonry enclosurewith cover plate having locking arrangement and watering pipeof 2.7 metre long etc. with alternative layer of 150mm thick charcoal/ coke and salt as required. For UPS. All earth pits installation & testing shall be as per IS 3043 with latest amendments.

SET 1.00

3.0 Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm)

Mts 90.00

4.0 Providing and laying earth connection from earth electrode with 4.00 mm dia copper wire in 15 mm dia G.I. pipe from earth electrode including connection with copper thimble excavation and re-filling as required.

Mts. 5.00

5.0 Providing and fixing 4.00 mm dia copper wire on surface or in recess for loop earthing as required.

Mts. 25.00

TOTAL EARTHING Rs.

G DATA / TELEPHONE WAIRING

14

1.0 Supply of all required materials and laying of CAT-6 LAN wairing from server to Hub and Hub to computer I/O Points of approved brand ((D-Link/Digilink/Amps ) laid through rigid FR/FRLS PVC conduits of 20mm Dia 1.5 mm thick of ISI mark duly burried under floor with necessary chasing / breaking in floor and to be refinished with all necessary civil material etc. or to be cleated on wall / ceiling with saddles / spacer etc. necessary termination etc. completeas in all respect including making good to all damages caused and as per the direction of Consultant and Engineer-in-charge.

Mts 1,000.00

2.0 Supply of all required materials & laying 2 pairs 0.51 cross section telephone wires of ITI approved laid through rigid FR/FRLS PVC conduits of 20mm Dia 1.5 mm thick of ISI mark duly burried under floor with necessary chasing / breaking in floor and to be refinished with all necessary civil material etc. or to be cleated on wall / ceiling with saddles / spacer etc. necessary termination etc. completeas in all respect including making good to all damages caused and as per the direction of Consultant and Engineer-in-charge.

Mtrs.

200.00

3.0 Supply of all required materials & laying 10 pairs telephone copper cable laid through rigid FR/FRLS PVC conduits of 20mm Dia 1.5 mm thick of ISI mark duly burried under floor with necessary chasing / breaking in floor and to be refinished with all necessary civil material etc. or to be cleated on wall / ceiling with saddles / spacer etc. necessary termination etc. completeas in all respect including making good to all damages caused and as per the direction of Consultant and Engineer-in-charge.

Mtrs.

60.00

4.0 Providing and fixing 50 pair kron box duly enclosed in metal powder coated box with locking arrangement complete with necessary terminations.

No. 1.00

5.0 Supply , fixing of RJ 45 information outlet (I/O) with safey sutter of D-link make with front modular cover plate, flush box metallic or PVC for trucking system etc.

Nos. 58.00

6.0 Supply , fixing , testing of RJ11 Modular Telephone socket point with suitable GI boxes complete in all respect as per direction of EIC .

Nos. 19.00

15

7.0 Fitting Charges for Refitting of Exisiting Data Racks including temination and testing. The cost also includes all temporay connections if any required for both power and data supply during execution of the work for running of barnches.

L.S 1.00

8.0 Supply & fixing 1Mtr long E-CAT 6 PATCH Cord (Make D-LINK,AMPor Equivalent Make)

No. 58.00

9.0 Supply & fixing 2Mtr long E-CAT 6 PATCH Cord (Make D-LINK,AMP or Equivalent Make)

No. 58.00

TOTAL DATA / TELEPHONE WAIRING Rs.

H PUBLIC ADRESSING SYSTEM 1.0 Supply, installation and testing of the following

items with ncessary M.S. iron frame/enclosure as nessary as per specification including cutting necessary ceiling fixing all accessories, G.I boits, nuts, washers, etc painting, earthing complite as required with other details asper enclosed specification AHUJA Make.

1.1 75 Watt PA system with control desk Comprising 1 nos of Microphone With Press to talk switch and stand ( Ahuja Make PRO - 3200), selector switch, mixing Amplifier 75 Watt Ahuja Make DPA 770),Digital player, mp3 Player with USB Reader & Remote control cables with with sockets , interconnections, earthing Ciomplite as required

Nos 1.00

1.2 Supply, installation and testing of External speaker 8 watt unit ( AHUJA Make: CS 6081T) in finished enclosure suitable for wall/celling mountinting with external colour matching asper the final finish as required and having the following rating. Wiring from PA system Amplifier ( 4 points in One Circuit )Make Ahuja/ Boss ( Should be Ahuja Make : CS6081T or Equivalant Speaker )( 6" Dia Speaker)

Nos 12.00

1.3 Supply of all required materials and laying of speaker wire (2R X 1.0 Sqmm )FRLS multi stranded copper conductor PVC insulated wires (with proper R,Y,B color code) pulled through heavy gauge PVC conduits from spiker point to amplifiar including cost of all labour materials.

Mts 200.00

TOTAL PUBLIC ADRESSING SYSTEM Rs.

I BUYBACK OF OLD MATERIALS

16

Removal of exsiting wiring for lighting, fans, AC, Computers data cable, cable, Wires, DB, Panels, other accessories etc. and taking away the material as buy back (Excluding fans & cable to be used as required ) from the existing Premises.

L.S ( - )

TOTAL BUYBACK OF OLD MATERIALS Rs.

Electrical and Allied work Price Breakup

A ELECTRICAL WIRING WORK

B COMPUTER WIRING WORK

C A.C. WIRING WORK

D PANEL BOARD & DISTRIBUTION BOARDS.

E FITTINGS OF FIXTURES

F EARTHING

G DATA / TELEPHONE WAIRING

H PUBLIC ADRESSING SYSTEM

I TOTAL (in Rs.) Excluding GST

J BUYBACK OF OLD MATERIALS (-)

G.TOTAL (in Rs.) Excluding GST ( I – J)

Total Amount in Word…………………………………………………………………………………………………………………………………….. Note: - The quoted prices shall be firm and inclusive of all duties, transportation, handling, loading and unloading at site, road permit, etc and no extra will be permitted. GST will be paid extra as per actual.

SIGNATURE OF THE CONTRACTOR WITH SEAL