original instruments and implants of the association for the study...

Original Instruments and Implants of the Association for the Study of Internal Fixation —AO ASIF

Ratcheting Screwdriver Handle [311.023]For manual insertion of Synthes CMF screws

Features

• Cuts all 2.0 mm plates

• Bends 2.0 mm plates in-plane and out-of-plane

• “Duckbill” end permits out-of-planebending of all mandible plates and easily bends the last segment

• Simple, single-handed use for easy bending

• Etching on both sides of the instrument illustrates cutting and bending sequence

Featured Instruments

Features

• For use with 1.5 mm, 2.0 mm, 2.4 mm and 3.0 mm screws

• Ergonomic, one-piece design—no disassemblyrequired for cleaning

• Clearly marked forward and reverse ratchetpositions allow easy insertion and removal of screws

• Locked position allows use as a fixed handle

• Allows quick connection to all existing Synthes CMF hex coupling instruments

2.0 mm Mandible Locking Plate (MLP) Bender/Cutter [329.143]For bending and cutting 2.0 mm plates

1

Graphic Cases for Mandible Modular Fixation System

4 -High Case [690.621] (with two instrument levels)

• Holds 8 insert trays

– 4 in level 1

– 4 in level 2 OR


– 3 in level 1 (when a basic tray is used)

– 4 in level 2

• Module storage options in levels 3 and 4

– 4 small modules OR

– 2 large modules OR

– 1 large and 2 small modules (as configured at left)

• 690.621 comes with

– Graphic Case

– Case Lid (also sold separately)

– Two dividers (also sold separately)

– Two insert tray holders (also sold separately)

4 -High Case, long [690.660] (with two instrument levels)

• Holds up to 12 insert trays

• Module storage options in levels 3 and 4





– Graphic Case

– Case Lid


– Two insert tray holders

3-High Case [690.620] (with one instrument level)


– 4 in level 1 OR


– 3 in level 1 (when a basic tray is used)

• Module storage options in lower 2 levels





– Graphic Case

– Case Lid (also sold separately)


– One insert tray holder (also sold separately)

Note: The 3-High Case does not have a second instrument level.

4-High Case, long 690.660

4-High Case 690.621

3-High Case 690.620

2

Note: Unless otherwise noted, tray will hold one of each indicated item.

• Plate Holding Forceps with ball, for 2.4 mm plates[398.66] (holds 2)

• Bone Reduction Forceps (holds 2)– Large [398.985]– Small [398.986]– Small, Straight [398.987]

• Depth Gauge, for 2.0 mm/2.4 mm screws [319.007]or [319.53]

• Plate Holding Forceps [347.98]

• 2.0 mm/2.4 mm Universal Drill Guide [323.204]

Standard Insert Tray [690.645](Takes up the space of 4 inserts)

This tray is designed to hold:

• Combination Bending/Cutting Pliers [391.965]

• Combination Bending Pliers [347.964]

• Short-Cut Plate Cutter, for 2.4 mm plates [391.967](holds 2)

• 2.0 mm MLP Bender/Cutter [329.143]

• Combination Bending Pliers, for 2.0 mm/2.4 mm[329.142], or 2.7 mm/3.5 mm plates [329.15]

• Bending Irons (holds 2)– Universal Bending Iron [329.031]– Bending Iron, for 2.4 mm plates [397.371]

• Screwdriver Handles (holds 2)– Ratcheting Screwdriver Handle [311.023]– Large Screwdriver Handle with hex coupling

[311.007]

Instrument Insert TraysGraphic Cases for Mandible Modular Fixation System

4-High Case, long 690.660

4-High Case 690.621

3-High Case 690.620

Note: All items are sold separately.

3


Basic Mandible Insert Tray [690.624] (Takes up the space of 2 inserts)

This tray is designed to hold:

• Screwdriver Handles (holds any 2)– Ratcheting Screwdriver Handle [311.023]– Screwdriver Handle with hex coupling, large [311.007]

• Plate Holding Forceps with ball, for 2.4 mm plates [398.66] (holds 2)

• Bone Reduction Forceps (holds any 2)– Large [398.985]– Small [398.986]– Small, Straight [398.987]

• Depth Gauges

– For 2.0 mm and 2.4 mm screws [319.007]– For 2.0 mm, 2.4 mm and 3.0 mm screws [319.53]

• Plate Holding Forceps [347.98]

• 2.0 mm/2.4 mm Universal Drill Guide [323.204]

Craniofacial Insert Tray [690.626] This tray is designed to hold:

• Mesh Cutter [391.952]

• Plate Cutter [391.98]

• Screwdriver Handle with hex coupling, small [311.005]

• Screwdriver Blades with hex coupling (each slot holds 2)– 1.5 mm Blades– 2.0 mm Blades– 2.4 mm Blades

• Plate Holding Tools (holds 2)– Plate Holding Instrument, for 1.0 mm and 1.3 mm plates [347.986]– Plate Holding Instrument, for 1.5 mm and 2.0 mm plates [347.987]– Screw Holding Forceps, locking, for 1.0 mm and 1.3 mm screws [348.95]– Plate Holding Forceps, locking, for 1.0 mm and 1.3 mm plates [348.98]

4

Instrument Insert Trays (continued)


Universal Trocar Insert Tray [690.627]This tray is designed to hold:

• Universal Trocar Handle [397.211]

• Malleable C-Retractor [397.232]

• Cheek Retractor Blades (holds 2)– 2.0 mm [397.42]– 2.4 mm [397.22]

• Cheek Retractor Rings (holds 2)– 2.0 mm [397.43]– 2.4 mm [397.23]

• 2.4 mm Cannula and Obturator [397.212]

• 2.0 mm Cannula and Obturator [397.213]

• Drill Guides (holds 3)– 1.5 mm [397.216]– 1.8 mm DCU Compression [397.265]– 1.8 mm DCU Neutral [397.263]

• Drill Bits/Taps (each slot will hold 2)

Lag Screw Insert Tray [690.628] This tray is designed to hold:

• Countersinks with centering pins, for 2.4 mm screws [310.805]

• Drill Bits (each slot holds 2)

• 1.8 mm Insert Drill Guide [397.282]

• 2.4 mm Drill Guide [397.285]

• Lag Screw Cannula [397.225]

• Lag Screw Pointer [397.226]

• 2.4 mm Titanium Cortex Screws [401.520E–401.540E] (screw rack holds 20)

5


Ratcheting Screwdriver Insert Tray [690.629] This tray is designed to hold:

• Ratcheting Screwdriver Handles (holds 2)– Ratcheting Screwdriver Handle, one piece [311.023]– Screwdriver Body [311.014] with Small Handle [311.016]

or Large Handle [311.017]

• Holding Sleeve [313.97]

• Screwdriver Blades with hex coupling (2 slots—each slot will hold 2)– 1.5 mm blades– 2.0 mm blades– 2.4 mm blades

Basic Screwdriver Insert Tray [690.630] This tray is designed to hold:

• Screwdriver Handles (holds any 2)– Screwdriver Handle with hex coupling, small [311.005]– Screwdriver Handle with hex coupling, medium [311.006]

• Screwdrivers (fixed handle) (holds any 2)– Cruciform [313.96]– 1.5 mm/2.0 mm PlusDrive, self-retaining [313.251]– 2.4 mm cruciform, self-retaining [313.925]


Screw Caddy Insert Tray [690.632] This tray is designed to hold:

• 2.0 mm screws (holds 36)

• 2.4 mm/3.0 mm screws (holds 36)

Combination Bender/Cutters Insert Tray [690.634] This tray is designed to hold:

• 2.0 mm Mandible Locking Plate Bender/Cutter [329.143]

• Combination Bending Pliers, for 2.0 mm and 2.4 mm plates [329.142]

• Bending Pliers, for 2.7 mm and 3.5 mm plates [329.15.98]


IMF Screw Compact Insert Tray [690.631] This tray is designed to hold:

• Precut cerclage wire (holds 20)– 0.5 mm [291.230.98]– 0.6 mm [291.240.98]

• 1.5 mm Drill Bits, with 12 mm stop (holds 2)

• 2.4 mm/3.0 mm Cruciform ScrewdriverBlade, hex coupling [313.939]


• 2.0 mm IMF screws, self-drilling – 8 mm [201.928] (holds 15)– 12 mm [201.932] (holds 15)

6


Note: Recommend storing in top instrument level.

7

Shortcut Plate Cutters Insert Tray[690.635] This tray is designed to hold:

• Shortcut Plate Cutter for 2.4 mmplates [391.967] (holds 2)

Combination Bending Pliers Insert Tray [690.637] This tray is designed to hold:

• Combination Bending/CuttingPliers [391.965]

• Combination Bending Pliers[347.964]


Bending Irons Insert Tray[690.636] This tray is designed to hold:

• Bending Irons (holds 2)– Universal Bending Iron [329.031]– Bending Iron for 2.4 mm plates

[397.371]

8


Auxiliary Insert Tray [690.638] This tray is designed to function as an auxiliary bin. It is an empty tray with a mat.

Also Available

Lid, for quarter size insert trays [690.640]The lid allows individual insert traysto be stored separately outside ofthe set, while keeping the items in the tray securely covered. Thetranslucent lid allows contents ofthe tray to be seen.

9

Product Information

Mandible Modular Fixation System

CASE OPTIONS690.620 Graphic Case for Mandible Modular Fixation

System, 3-high690.621 Graphic Case for Mandible Modular Fixation

System, 4-high690.660 Graphic Case for Mandible Modular Fixation

System, 4-high, long

All three cases come with the required insert holder(s), moduledivider(s) and lids. Also available separately if needed:690.639 Insert Holder (for 690.620 and 690.621)690.642 Module Divider, for small module storage690.622 Lid, for Mandible Modular Fixation System

Graphic Cases (fits 690.620 and 690.621)

INSERT TRAY OPTIONS690.624 Basic Mandible Insert Tray 690.626 Craniofacial Insert Tray690.627 Universal Trocar Insert Tray690.628 Lag Screw Insert Tray690.629 Ratcheting Screwdriver Insert Tray 690.630 Basic Screwdriver Insert Tray 690.631 IMF Screw Compact Insert Tray 690.632 Screw Caddy Insert Tray690.634 Combination Bender/Cutters Insert Tray 690.635 Shortcut Plate Cutters Insert Tray690.636 Bending Irons Insert Tray 690.637 Combination Bending Pliers Insert Tray690.638 Auxiliary Insert Tray690.640 Lid, for quarter-size insert tray690.645 Standard Instrument Tray, full size

690.639 Insert Holder690.634 Combination Bender/Cutters Insert Tray690.626 Craniofacial Insert Tray690.624 Basic Mandible Insert Tray

690.639 Insert Holder690.635 Shortcut Plate Cutters Insert Tray690.627 Universal Trocar Insert Tray690.624 Basic Mandible Insert Tray

Sample configurations for insert holder with insert trays:

Sterilization Parameters for Cases [690.620, 690.621 and 690.660]These Synthes cases with all additionally available items, as marked in the case or modules, can be sterilized by the following parameters.For more information, please see graphic case package insert.

Method Cycle Temperature Exposure Time Dry Time

Steam Gravity 132°–135°C 22 Minutes 25 MinutesDisplacement (270°–275°F)

(Wrapped)

Steam Prevacuum 132°–135°C 8 Minutes 20 Minutes(Wrapped) (270°–275°F)

2.0 mm Titanium Mandible Locking Plate SetModule Case

304.744

10

MODULE OPTIONS304.744 Module Case, for 2.0 mm Titanium Mandible Locking

Plate Set (includes base, lid and standard plate insert tray)304.765 Insert Tray, for double angle plates (for 304.744)304.766 Insert Tray, for specialty plates (for 304.744)304.767 Insert Tray, for compression plates (for 304.744)

304.673 2.0 mm Mandible Locking Plate Module (Small)

Screw Part Number Inserts304.700T27 for 401.354–401.374304.700T35 for 401.386–401.398304.700T46 for 401.845–401.848306.791 for 401.291–401.299306.792 for 401.041–401.052306.793 for 401.955–401.957306.794 for 401.061–401.065306.795 for 401.791–401.799

Screw Length Markers304.105– for 5 mm–18 mm screws304.118304.105W– for 5 mm–8 mm self-drilling screws304.108W

INSTRUMENTS313.251 1.5 mm/2.0 mm PlusDrive Screwdriver, self-retaining

1.5 mm/2.0 mm PlusDrive Screwdriver Blades, self-retaining

313.252 96 mm, hex coupling313.253 72 mm, hex coupling313.254 52 mm, hex coupling

2.0 mm StarDrive Screwdriver Blades, self-retaining313.843 Long, mini quick coupling313.848 Long, hex coupling313.842 Short, mini quick coupling313.847 Short, hex coupling

312.155 1.5 mm Drill Guide, for 2.0 mm Mandible Locking Plates

312.154 1.5 mm Threaded Drill Guide, long, for 2.0 mm Mandible Locking Plates

397.440 1.5 mm Threaded Drill Guide, short,for 2.0 mm Mandible Locking Plates

2.0 mm Mandible Locking Plate Module

1.5 mm Drill Bits, Stryker J-latch317.435 60 mm stop, 85 mm317.835 110 mm317.836 125 mm

2.0 mm Cruciform Screwdriver Blades, with Spring Holding Sleeve

314.675 Short, hex coupling314.684 Long, hex coupling314.672 Short, mini quick coupling314.673 Long, mini quick coupling

311.204 Tap for 2.0 mm Mandible Locking Screws,100 mm

Note: Contents ordered separately unless otherwise noted.

2.0 mm Mandible Locking Plate Module (Small)304.673

11

Screws with PlusDrive recess401.291– 2.0 mm Titanium Locking Screws, self-tapping 401.299 5, 6–18 mm (5/pkg.) 401.041– 2.0 mm Titanium Cortex Screws, self-tapping 401.044 4, 5, 6, 8 mm (5/pkg.) 401.045– 2.0 mm Titanium Cortex Screws, coarse pitch401.052 self-tapping, 10–24 mm (5/pkg.) 401.061– 2.0 mm Titanium Cortex Screws, self-drilling 401.065 4, 5, 6, 7 and 8 mm (5/pkg.) 401.955– 2.0 mm Titanium Locking Screws, self-drilling 401.957 5, 6, 8 mm (5/pkg.) 401.791E– 2.4 mm Titanium Emergency Screws 401.799E 5, 6, 8–18 mm (1/pkg.)

Screws with StarDrive Recess401.245– 2.0 mm Titanium Locking Screws, self-tapping 401.258 5, 6–18 mm (5/pkg.)401.355– 2.0 mm Titanium Cortex Screws, self-tapping 401.368 5, 6–18 mm (5/pkg.) 401.854– 2.0 mm Titanium Cortex Screws, coarse pitch 401.874 self-tapping, 4, 5, 6, 7, 8 – 24 mm (5/pkg.) 401.845– 2.0 mm Titanium Locking Screws, self-drilling 401.848 5, 6, 8 mm (5/pkg.) 401.386E– 2.4 mm Titanium Emergency Screws 401.398E 6, 7, 8–18 mm (1/pkg.)

Note: Contents ordered separately unless otherwise noted.* Large Module only

MANDIBLE LOCKING PLATES (MLP)2.0 mm Titanium Mini Locking Plates

447.046 Narrow, 4 holes, malleable447.047 Narrow, 6 holes, malleable447.048 Narrow, 4 holes447.049 Narrow, 6 holes447.050 Adaption, 12 holes*447.051 Adaption, 20 holes447.053 Tension Band, 4 holes447.055 Broad, 4 holes447.057 Broad, curved, 4 holes447.304 Pre-bent Tension Band, 4 holes, right*447.305 Pre-bent Tension Band, 4 holes, left*447.308 Double Wide, 12 holes, malleable*447.309 Double Wide, 9 holes, malleable*447.310 Box, malleable*447.312 Strut, 8 holes, malleable*447.315 Curved Strut, 8 holes, malleable*447.317 Double Y-Plate, malleable*447.318 L-Plate, right, malleable*447.319 L-Plate, left, malleable*

PlusDrive recess StarDrive recess

2.0 mm Titanium Intermediate Locking Plates447.101 6 holes447.102 12 holes447.204 Compression, 4 holes*447.205 Compression, 5 holes*447.206 Compression, 6 holes*447.208 Compression, 8 holes*447.210 Angle Compression, 6 holes*447.212 Angle Compression, 8 holes*447.215 Crescent, 5 holes*447.217 Crescent, 7 holes*

Specialty Plates Insert Tray304.766*

Compression Plates Insert Tray304.767*

12

MANDIBLE LOCKING PLATES (MLP) (cont’d)

2.0 mm Titanium Large Locking Plates447.103 3 x 3 holes447.104 6 holes 447.105 12 holes447.106 20 holes447.108 6 x 21 holes, right447.109 6 x 21 holes, left447.117 Crescent, 3 x 3 holes447.118 Angled, 3 x 3 holes447.119 Angled, 4 x 4 holes447.404 Double Angle, 4 x 20 x 4 holes*447.405 Double Angle, 5 x 22 x 5 holes*447.406 Double Angle, 6 x 24 x 6 holes*

2.0 mm Titanium Extra Locking Plates447.412 12 holes*447.420 20 holes*447.422 6 x 21 holes, right*447.423 6 x 21 holes, left*447.424 Double Angle, 4 x 20 x 4 holes*447.425 Double Angle, 5 x 22 x 5 holes*447.426 Double Angle, 6 x 24 x 6 holes*

TEMPLATESFor 2.0 mm Titanium Mini Locking Plates

329.528 Adaption, 20 holes329.529 6 holes

For 2.0 mm Titanium Intermediate Locking Plates329.525 6 holes329.527 12 holes329.571 Crescent, 5 and 7 holes329.572 Angle Compression, 6 and 8 holes329.573 Compression, 4, 6 and 8 holes

For 2.0 mm Titanium Large and Extra Locking Plates329.521 6 x 21 holes, right329.522 Angled, 4 x 4 holes329.523 Crescent, 3 x 3 holes329.524 20 holes329.526 3 x 3 holes329.530 6 x 21 holes, left329.574 Double Angle, 4 x 20 x 4 holes329.575 Double Angle, 5 x 22 x 5 holes329.576 Double Angle, 6 x 24 x 6 holes

2.0 mm Mandible Locking Plate Module (continued)

Specialty Plates Insert Tray304.766*

Note: Contents ordered separately unless otherwise noted.* Large Module only

329.528

329.527

329.523

329.524

329.526

329.571

13

2.4 mm/3.0 mm Locking Reconstruction and Trauma Module

2.4 mm/3.0 mm Locking Reconstruction and Trauma Plate Module Case

304.745

MODULE OPTIONS304.745 Module Case for 2.4 mm/3.0 mm Locking Reconstruction

and Trauma plates (includes base, lid and standard LRP plate insert tray)

304.763 2.4 mm Mandible Trauma Plates Insert Tray (for 304.745)304.764 2.4 mm Microvascular Plates Insert Tray (for 304.745)

Screw Part Number Inserts (included with 304.745)306.796 for 401.508–401.518306.797 for 497.668–497.678306.798 for 497.690–497.695306.799 for 401.558–401.568

Screw Length Markers304.106– for 6 mm–18 mm screws304.118

INSTRUMENTS310.512 1.8 mm Drill Bit, Stryker J-latch, 100 mm310.522 1.8 mm Drill Bit, Stryker J-latch, 125 mm397.441 1.8 mm Threaded Drill Guide, short,

for Locking Reconstruction Plate 397.218 1.8 mm Threaded Drill Guide, for Locking

Reconstruction Plate

310.542 2.4 mm Drill Bit, Stryker J-latch, 125 mm397.442 2.4 mm Threaded Drill Guide, short,

for Locking Reconstruction Plate397.224 2.4 mm Threaded Drill Guide, for Locking

Reconstruction Plate

497.689 Titanium Bending Insert Screw, for Locking Reconstruction Plate

TEMPLATESFor Locking Reconstruction Plate

329.401 4 x 20 x 4 holes, double-angled329.402 5 x 22 x 5 holes, double-angled329.403 6 x 24 x 6 holes, double-angled329.769 6 x 23 holes, angled329.40.98 37 holes, straight

329.78 For Universal Fracture Plates (449.38, 449.40)

For Microvascular Plates 329.79 4 x 20 x 4 holes329.80 5 x 22 x 5 holes329.81 6 x 24 x 6 holes

SCREWS401.506– 2.4 mm Titanium Cortex Screws, 401.540 self-tapping, 6 mm–40 mm (5/pkg.)401.558– 2.7 mm Titanium Emergency Screws, 8–18 mm401.568 (5/pkg.)497.668– 2.4 mm Titanium Locking Screws, for Titanium 497.684 Locking Reconstruction Plate, 8 mm–24 mm (5/pkg.)497.690– 3.0 mm Titanium Locking Screws, for Titanium 497.698 Locking Reconstruction Plate, 8 mm–24 mm (5/pkg.)

PLATESTitanium Locking Reconstruction Plates

449.612 12 holes, straight449.621 20 holes, straight449.632 6 x 23 holes, left, angled449.633 6 x 23 holes, right, angled449.636 4 x 20 x 4 holes, double angled449.637 5 x 22 x 5 holes, double angled449.638 6 x 24 x 6 holes, double angled449.651 3 x 3 holes, crescent shape449.652 3 x 3 holes449.653 4 x 4 holes, angled449.654 5 x 8 holes, left angled449.655 5 x 8 holes, right angled

Titanium Locking Reconstruction Plates, with Condylar Head

449.644 3 x 16 holes, right449.645 3 x 16 holes, left449.646 4 x 18 holes, right449.647 4 x 18 holes, left449.648 5 x 20 holes, right449.649 5 x 20 holes, left


2.4 Microvascular Plates, optional insert tray for 304.745

304.764

14

2.4/3.0 mm Locking Reconstruction and Trauma Module (continued)

2.4 mm Mandible Trauma Plates, optional insert tray [304.763] accommodates:2.4 mm Titanium Compression Tension Band Plates

449.100 4 holes449.110 6 holes

2.4 mm Titanium LC-DCP Plates449.14 4 holes449.15 5 holes449.16 6 holes449.24 Crescent, 4 holes449.26 Crescent, 6 holes

2.4 mm Titanium Universal Fracture Plates449.38 Straight, 8 holes449.40 Straight, 10 holes449.82 with angle, 3 x 3 holes449.84 with angle, 4 x 4 holes

ALSO AVAILABLE2.4 mm Titanium Eccentric LC-DCP Plates

449.234 4 holes449.236 6 holes

2.4 mm Titanium Microvascular Plates, Insert Tray [304.764] accommodates:

449.412 Straight, 12 holes449.420 Straight, 20 holes449.446 with angle, 6 x 18 holes, right449.447 with angle, 6 x 18 holes, left449.450 with double angle, 4 x 20 x 4 holes449.451 with double angle, 5 x 22 x 5 holes449.452 with double angle, 6 x 24 x 6 holes

ALSO AVAILABLE2.4 mm Titanium Microvascular Plates, straight

449.414 14 holes449.416 16 holes449.418 18 holes449.422 22 holes449.424 24 holes

2.4 mm Titanium Microvascular Plates, with angle449.440 4 x 8 holes, right449.441 4 x 8 holes, left449.442 4 x 16 holes, right449.443 4 x 16 holes, left449.444 5 x 17 holes, right449.445 5 x 17 holes, left449.448 6 x 21 holes, right449.449 6 x 21 holes, left

2.4 Mandible Trauma Plates, optional insert tray for 304.745

304.763


15

Locking Reconstruction Plate Module (small)304.701

andScrew Length Marker Kit

306.660

2.4 mm Mandible Trauma Module (small) 304.654


306.658

2.4 mm Microvascular Module (small) 304.656


306.660

OTHER MODULE OPTIONS

16

IMF Screw Set [115.630]

Wire Twister398.906

Wire-Cutting Scissors, straight pointed

398.909

2.4 mm/3.0 mm Cruciform Screwdriver Blade,with hex coupling

313.939

(shown with Holding Sleeve 313.97)

2.4 mm Screwdriver with Holding Sleeve313.94

(consists of 313.96 and 313.97)

MODULE304.708 IMF Screw Module

IMPLANTS201.928 2.0 mm IMF Screw, self-drilling, 8 mm,

6 pkgs. of 5201.932 2.0 mm IMF Screw, self-drilling, 12 mm,

6 pkgs. of 5291.230.98 0.5 mm (24 gauge) Precut Cerclage Wire,

175 mm, 2 pkgs. of 10291.240.98 0.6 mm (22 gauge) Precut Cerclage Wire,

175 mm, 2 pkgs. of 10

INSTRUMENTS313.939 2.4 mm/3.0 mm Cruciform Screwdriver Blade

with hex coupling313.94 2.4 mm Screwdriver with Holding Sleeve317.72 1.5 mm Drill Bit, Stryker J-latch, with 12 mm

stop, 2 ea.398.906 Wire Twister398.909 Wire-Cutting Scissors

ALSO AVAILABLE1.5 mm Drill Bits, with 12 mm stop

317.82 Mini quick coupling316.652 Hex coupling

398.905 Auto Wire Twister398.907 Wire Cutting Scissors, universal398.908 Wire Manipulator

304.728 IMF Screw Compact Tray (accommodates up to 30 screws, 20 of one wire size, and two 1.5 mm Drill Bits with stop)

IMF Screws201.928 and 201.932

© SYNTHES CMF 2004 LC-DCP, PlusDrive, SYNTHES and ASIF are trademarks of SYNTHES (USA) and SYNTHES AG Chur. Printed in U.S.A. 8/05 J5483-B

SYNTHES CMF1302 Wrights Lane East West Chester, PA 19380Telephone: (610) 719-5000To order: (800) 523-0322Fax: (610) 251-9056

SYNTHES (CANADA) LTD.2566 Meadowpine BoulevardMississauga, Ontario L5N 6P9Telephone: (905) 567-0440To order: (800) 668-1119Fax: (905) 567-3185

original instruments and implants of the association for the study...

Documents